Search Documents

SYMPOSIUM ON THE RECOVERY OF PYRITE The proceedings of the Symposium on the Recovery of Pyrite, held in Johannesburg in June 1969, may be ordered from the Secretary, S.A.I.M.M., P.O. Box 61019, Marshalltown, Transvaal, at the reduced price of R5.00. Papers and addresses presented at the Symposium were: Opening Address by Mr J. K. E. Douglas (President). "The world sulphur position," by W. C. J. van Rensburg (Member). "The South African sulphur position," by D. L. Taylor (Member). "The recovery of pyrite at Government Gold Mining Areas Limited," by R. J. Westwood (Member), G. S. Stander (Affiliate) and H. P. Carlisle (Member). "Recovery of pyrite concentrates from colliery-waste discards-A preliminary assessment," by W. A. Gilbert (Visitor) and E. A. Nugent (Member). "The role of pyrite in upgrading the uranium content of Witwatersrand conglomerate ores by means of the heavy-medium separation process," by D. J. Tutt (Associate Member). "Pyrite recovery by jigs at Durban Roodepoort Deep Limited," by E. J. Dominy (Affiliate), F. Diamond (Affiliate) and A. D. Graham (Affiliate). "The storage of pyrite concentrates," by Joan C. Campkin (Visitor) and P. J. Lloyd (Member). "The flotation plants of the Anglo-Transvaal Group," by L. A. Bushell (Member). "Pyrite flotation with amines and cyanidation of the products," by E. H. D. Carman (Member). "Gold recovery by cyanidation from mill products obtained after pyrite flotation," by P. G. Mrkusic (Graduate), M. Sciarone (Visitor) and H. E. Simonsen (Visitor). "The influence of sulphydryl and cationic flotation reagents on cyanidation of native gold," by K. G. Ashurst (Visitor) and W. P. Finkelstein (Member). "Laboratory tests on the flotation of pyrite from Witwatersrand gold ores by cationic collector," by J. Levin (Member), and M. L. Veitch (Visitor). Closing Address, by Dr R. E. Robinson (Director, National Institute for Metallurgy). INCOME TAX: POST-GRADUATE STUDY COURSE CONCESSION As a result of representations made by the Associated Scientific and Technical Societies of S.A. and the Suid-Afrikaanse Akademie vir Wetenskap en Kuns, engineers and scientists will now be allowed to deduct expenses incurred on post-graduate study courses from their taxable income. The conditions of this concession are set out in section 16 of the Income Tax Act, 1969, which reads as follows: 16. (1) The following section is hereby substituted for section 16 of the principal Act: 16. "Notwithstanding the provisions of section 23(a) and (b), there shall be allowed to be deducted from the income of any person who is a dentist or medical practitioner or practises any profession referred to in paragraph (a), so much as the Secretary may allow of any expenditure incurred by such person in the circumstances contemplated in paragraph (c), if the Dental Association of South Africa in the case of a dentist, or the Medical Association of South Africa in the case of a medical practitioner, or the "Suid-Afrikaanse Akademie vir Wetenskap en Kuns" or the Associated Scientific and Technical Societies of South Africa in any other case, certifies in such form as the Secretary may prescribe that such person- (a) if he is not a dentist or medical practitioner, is the holder of a degree in engineering or allied technology or natural sciences awarded by a recognized university on completion of a prescribed minimum period of study of not less than four academic years or the equivalent thereof and enabling the holder thereof to practise the profession of an engineer or a profession for which advanced and specialised scientific knowledge is required which relates directly to- (i) the development or exploitation of natural resources; (ii) mining or prospecting for minerals; (iii) the production of pastoral, agricultural or forest produce ; (iv) the breeding or care of farm animals; (v) any industrial process; or (vi) the training of specialists in any branch of science or technology connected with any aforementioned profession; (b) has practised his profession for not less than three years; and (c) has incurred such expenditure during the year of assessment in respect of the attendance by him of any postgraduate study course approved by such body to improve his qualifications for carrying on his profession in the Republic". (2) The amendments effected by subsection (1) shall first take effect in respect of assessments for the year of assessment ending on the twenty-eighth day of February, 1970. From this section it is clear that the concession will only be granted if the application is accompanied by a certificate, which certificate must be either signed by the Chairman of Die Akademie or the President of the Associated Societies. In terms of the authority granted such certificates must certify that: (i) the taxpayer concerned has practised his profession for not less than three years; (ii) the expenditure was incurred by the taxpayer during the year of assessment indicated in the certificate; (iii) the expenditure was incurred by the taxpayer in respect of the attendance by him of a post-graduate study course approved by the Associated Scientific and Technical Societies of South Africa or Die Suid-Afrikaanse Akademie vir Wetenskap en Kuns, as the case may be, to improve his qualifications for carrying on his profession in South Africa; (iv) the taxpayer is the holder of a degree in engineering or allied technology or natural sciences, which degree was awarded by a recognized university,

By F. P. Agterberg, A. G. Fabbri

"A statistical analysis was done on the locations of 718 copper and 1 257 gold deposits in Abitibi. This area of about 20 000 square miles is one of the better-explored metal-producing areas of Canada.Patterns of clusters were studied by harmonic analysis. Several two-dimensional power spectra showed a number of distinct peaks. Sets of crest lines for patterns of interfering waves were constructed on the basis of these peaks. They pass through elongated clusters of deposits which are spaced more or less equally. For copper these periodic regularities in location may coincide with geological structures largely of Archean age (major fractures and sedimentary belts indicating synclinal structures). A directional relationship with swarms of diabase dykes of known ages and distinct attitudes indicates that the gold mineralization is, in part, younger than the copper mineralization."

Jan 1, 2014

By S. V. Lukichev, O. V. Nagovitsyn, V. V. Laptev

In this paper the authors describe the developed algorithms of short- and medium-term planning of underground mining operations. The algorithms were developed using the example of the flat-back cut-and-fill method, and provide multifactor accounting of mining conditions, technical and technological limitations: state and properties of the rock mass; the current mining situation; mining rules; availability of safety pillars; properties of the filling; additional characteristics of technological objects that complicate the driving of workings; sufficiency of human and technical resources; employee specialisation; existing machinery and equipment; opportunities and limitations of the transport scheme of the mine, and work schedule. The paper is presented by means of a dynamic model of mining development, which shows the sequence of mining operations in the mine workings. Besides animation, the tool provides an opportunity to form tabular and graphical reports.

Sep 1, 2021

By M. M. Bwalya, F. K. Mulenga

"SynopsisThe application of the attainable region (AR) technique to the analysis of ball milling is currently limited to batch data. This paper introduces the use of the technique to continuous milling.To this end, an industrial open milling circuit processing a platinum ore was surveyed. Samples were collected and later characterized by means of laboratory batch testing. On site, several milling parameters were varied systematically so as to collect data for modelling purposes. These paramters included ball filling, slurry concentration, and feed flow rate. After data analysis, a simulation model of the open milling circuit was developed under MODSIM®, a modular simulator for mineral processing operations. The mill was then simulated and the data generated was analysed within the AR framework.Initial findings reveal an opportunity to gain valuable insight by studying milling using the AR technique. From an exploratory perspective and inasmuch as this study is concerned, feed flow rate, ball size, and ball filling were identified as being pivotal for the optimization of open ballmilling circuits. Mill speed, on the other hand, had only a limited effect on the production of particles in the size range -75 +10 µm.IntroductionGlasser and Hildebrandt (1997) propounded the attainable region (AR) as a technique for the analysis of chemical engineering reactor systems. Results have since been produced and tested on both the laboratory and pilot scales. The method results in a graphical description of chemical reactions by considering the fundamental processes taking place in the system, rather than the equipment. From the plotted graphs, the process and the reactors can be synthesized optimally into a flow sheet.The use of the AR method still has a long way to go as far as mineral processing is concerned. For instance, several articles have reported the application of the AR technique to ball milling: Khumalo et al. (2006, 2007, 2008); Khumalo (2007); Metzger et al. (2009, 2012); Metzger (2011); Katubilwa et al. (2011); Hlabangana et al. (2012). Their main shortcoming has been the exclusive use of laboratory batch grinding data.To address this deficiency, Mulenga and Chimwani (2013) proposed a way by which the technique could be extended to continuous milling. In effect, the batch milling characteristics of a platinum-bearing ore (Chimwani et al., 2013) were used and scaled up to an open milling circuit. Then, with simplifying assumptions, an attempt was made to optimize the residence time of particles inside the mill. Later, Chimwani et al. (2014a) presented some optimization examples involving various milling parameters. The sequence of published articles then paved the way for the study of industrial milling systems with the AR methodology."

Jan 1, 2015

By M. A. El-Sayed

"Double oxide films (bifilms) are significant defects in light alloy castings that occur when, during melt handling, the oxidized surface of the melt is folded over onto itself and then entrained into the liquid metal, encapsulating a portion of the local atmosphere. These defects create crevices in the final castings and have been shown to decrease tensile and fatigue properties, and also to increase their scatter, making casting properties unreproducible and unreliable. This paper reports on two different experiments performed to study the behaviour of such defects in Al alloys. In the first experiment and as a proxy for a bifilm, air bubbles were held in an Al-5Mg alloy melt for varying periods of time before the melt was allowed to solidify. The composition of the gas content of the bubbles was subsequently analysed using mass spectrometry to ascertain how it changed with time. In the other experiment the influence of the age of bifilms on the mechanical properties of Al-5Mg castings was assessed by holding castings in the liquid state for different times before solidification, followed by mechanical property testing and SEM and EDX studies of the fracture surfaces of tensile test bars. This research could provide a better understanding of the behaviour of double oxide film defects, and may lead to the development of new techniques by which these defects could be eliminated, or at least deactivated, in light alloy castings. Introduction One of the major structural defects affecting the reproducibility of mechanical properties of aluminium castings is the double oxide film defect (El-Sayed and Essa, 2017; El-Sayed and Ghazy, 2017). This type of defect is usually created as a result of poor filling system design. Owing to the very high reactivity of liquid Al-Mg alloy with oxygen in the air, the surface of the liquid metal can be considered to be permanently coated with an oxide film (Weigel and Fromm, 1990). As a consequence of surface turbulence, the oxidized metal surface can become folded over onto itself, but not fused, and then submerged into the bulk liquid, with a portion of the mould atmosphere being entrapped within it (Campbell, 2003; Al- Sayed, 2016; El-Sayed, Hassanin, and Essa, 2016)."

Nov 1, 2018

By Karl-H. Daum

Over many decades, numerous feasibility studies have demonstrated, that the production of sulphuric acid remains the most viable option of sulphur recovery from smelter off gas and abatement of SO2 emissions to the atmosphere. This is particularly more pronounced as smaller but more concentrated off-gas flows are to be treated from smelters, and enhanced sulphuric acid processes be-come available. Off-gas handling systems represent a significant capital and operating cost burden to the metallurgical operation. Modern pyrometallurgical smelter processes for sulphide ores based on the use of oxygen-enriched air, produce relatively small off-gas flows with high SO2 concentrations in the smelter gas of 30?60 %-vol. of SO2. This is a prerequisite for substantial cost reductions in the smelter off-gas handling and treatment system. As an alternative to sulphuric acid production, numerous scrubbing concepts with alkali or dual-alkali combinations as well as organic absorbents have been proposed. Also the reduction of the SO2 to elemental sulphur has frequently been studied. Very few of those alternative processes have been built in industrial scale, but all were generally characterized by none sustainable operation due to cost reasons, problems with issues related to chemicals used and by-products or poor availability. Thus the traditional concept of converting the SO2 to sulphuric acid is most common, although regarded as un-economic, but is at least a proven, environmentally sustainable and reliable way of sulphur gas processing. With the high acid price levels these days, operating companies are even able to generate significant revenue with their otherwise ?fatal? acid.

Jan 1, 2009

By C. O. Aksoy, G. G. U. Aksoy, A. Fisne, I. Alagoz, E. Kaya

Coal produced in underground mines is transported to the surface by means of conveyor belts throughout long roadways. The combustion of belts puts a large number of employees at great risk. Underground collieries differ from other underground mines -due to the combustible nature of the product. The most prevalent cause of belt fires in underground coal mine is spontaneous combustion due to oxidation of the coal, which also enables the conveyor belt to burn over time. In 2014, a belt fire in an underground coal mine in Manisa-Soma, Turkey caused 301 fatalities. A study has been conducted on this accident for approximately 3 years, consisting of combustion tests in a purpose-built research gallery, comparison of the test results with mine records of the accident, and CFD modelling of the mine environment. The intensity of the fire was sufficient to redirect the air flow underground, causin large amounts of toxic gases to fill almost the entire mine in approximately 15 minutes. It is recommended that CFD analysis be used in planning emergency action strategies in underground mines.

Dec 13, 2023

By D. Minson, G. Lindner, S. Miskovic

Thickening is an essential process in the mining industry and currently one of the most costeffective technologies for recovering water from tailings streams. Improved performance of thickeners can lead to significant energy savings, and increased recovery of water close to the mill. Its performance is directly affected by the rheological properties of slurry at the raking zone. To further understand the dynamics of slurry inside thickeners, a multiphase particle-in-cell method (MP-PIC), is used to investigate its behaviour on a sliding channel. Parameters like particle-size distribution (PSD), rheological properties, and domain discretisation were benchmarked to study its influence on highly dense flows. The slurry concentration by weight of the samples ranged between 60 to 70% of solids by mass, under which conditions it is known to behave like a non-newtonian fluid. An experimental flume, 0.2 m wide and 2 m long, was used for validation under different angles and slurry composition. Visual analysis of the slurry height and shape, as well as velocity measurements, were compared with numerical data. The preliminary results show the ability of MP-PIC method to represent different types of highly dense flows, while still being computationally affordable and practical for industrial use. Keywords: High density thickener, CFD, MP-PIC, multiphase-flow

Jan 1, 2020

By B. Emwanu, R. A. Raju

The implementation of new technology in mining can be likened to a paradoxical situation or dilemma, where, on one hand, major mining projects are not able to solicit investor funding unless it is proven that the business cases were developed using tried and tested mining methods. On the other hand, new and innovative mining technology and mining methods need first to demonstrate and prove themselves under real production conditions over a reasonable period before they can be considered bankable feasibility studies in the mining industry. This dilemma locks new mining technology investments in a continuous cycle of underinvestment. Technological innovations are particularly relevant to the mining industry, which deals with the challenges of depleting access to resources, requiring new solutions to remain sustainable and competitive. In the last decade, the mining industry has come to realise that technological innovations can directly contribute to its sustained competitive advantage (Sanchez, Hartlieb, 2020), helping to reduce costs, lessen environmental impact, increase production, and improve mineral recovery. While understanding barriers and drivers for technology adoption is important for the success of technology implementation efforts and the sustainability of the mining sector (Muduli et al., 2013), this paper suggests strategies to exit the dilemma, proposing a preliminary framework.

Oct 24, 2025

By T. Nyakudarika

The Unki Platinum Mines concentrator, employing an MF2 circuit configuration which includes fully-autogenous primary milling of run-of-mine (ROM) ore, was commissioned in November 2010. The project was Anglo American Platinum?s first PGM concentrator in Zimbabwe and would form a significant contribution to the group?s platinum production. The project financials demonstrated that the project was operating-cost sensitive. After reviewing the metallurgical testwork, mineralogical examinations, and the history of similar operations, it became apparent that the Unki ore characteristics rendered it amenable to autogenous milling. The primary ball mill, structurally designed for 30 per cent steel load, could be operated at the required initial phase throughput with fully-autogenous primary milling, realizing savings in both power requirements and grinding media consumption. The original mill sizing had been done with fully-autogenous milling in mind, but allowing for flexibility and mitigation in case of varied mining fragmentation. Since attaining steady state, target grinds have been achieved. This paper looks at the Unki ore characterization programme, design considerations, and the operational and control philosophy for a successful comminution circuit, and discusses the design to produce a flexible, low opex, mitigated comminution and overall MF2 flowsheet that is easily expanded in line with the potential for optimum exploitation of the orebody.

Jan 1, 2012

By V. Oberholzer

The presence of fines (particles smaller than 6 mm in diameter) causes hydrodynamic problems in gasifiers and therefore it is of great importance to minimize the amount of fine coal in the feed. This serves as motivation for understanding coal?s breakage mechanisms, which could lead to the ability to predict the generation of fines. The aim of this project was to simulate the pulsating effect of the conveyor belt in order to investigate factors influencing the breakage. Results indicated that an increased initial particle size had an increasing effect in the amount of fines generated. Weathering had an insignificant effect on the breakage of coal. To conclude, a breakage model was developed to describe the rate of breakage out of the top size when a combination of two breakage modes is present.

Jan 1, 2009

By D. Vogt

"Rock has been cut in the process of mining since before the invention of explosives. Today, we seek to return to cutting to reap the benefits of continuous operations for South African underground hard-rock mines, to improve speed of access to the orebody, and to improve the efficiency of mining operations.Development of new technology fits within a framework of engineering knowledge. By understanding the characteristics of the rock, the tools we use to cut it with, and the history of mining and rock cutting, we can see the genesis of the road-header, the longwall, and the continuous miner, all drag bit cutters. They have emerged as the solutions of choice for underground mining of softer materials such as coal and potash. In hard rock, the challenges are the forces required to break the rock, and the wear of the tools caused by the rock’s abrasiveness. Only disc cutters currently handle the challenges, and even then, often not economically. New materials like thermally stable diamond composite will help, as will combinations of mechanical cutters and other methods such as high-pressure water or high temperatures.It is not clear what will emerge as the consensus technique for hardrock cutting. Experience teaches that development is expensive and the market is small. Will mining companies partner with equipment developers to make the technological leap? Or will the solution come from a systems approach, not considered here?IntroductionBlasting is the dominant method of breaking rock for the purposes of mining. When used underground, blasting is part of a batch process. If rock can be cut rather than blasted, mining can become continuous, leading to process and efficiency improvements.Coal produced from underground mines is now predominantly excavated using mechanical means, but underground hard rock is still broken primarily by explosives.This paper traces the history of rock cutting, reviews the main physical processes that are or could be used, and comments on the future. It is written from the perspective of narrow-stope hard-rock mining typical of South African gold and platinum mines."

Jan 1, 2016

Your Council has pleasure in submitting its report for the year ended 30th June, 1970. COUNCIL The following served as Office Bearers during the year under review: Messrs J. K. E. Douglas (President), V. C. Robinson and Prof D. D. Howat (Vice-Presidents), R. C. J. Goode (Immediate Past President) and D. G. Maxwell (Honorary Treasurer). Members of Council: Mr. R. J. Adamson, Dr. M. G. Atmore, Mr M. Barcza, Dr J. M. Bereza, Messrs H. Britten, H. E. Cross, A. R. C. Fowler, G. W. Holl, Dr J. P. Hugo, Messrs N. A. Honnet, P. Lambooy, Prof J. de V. Lambrechts, Mr C. E. Mavrocordatos, Dr J. T. McIntyre, Messrs J. Meintjies, T. C. A. Meyer, J. A. Nixon, Prof R. P. Plewman, Dr R. E. Robinson, Messrs J. F. Reid, H. Simon and P. W. J. van Rensburg. Ten Council meetings were held during the year with an average attendance of seventeen and the standing committees held 45 meetings. FINANCE The annual accounts, which are attached to this report, show an excess of expenditure over income of R4,608 compared with R2,124 last year. This deterioration can be attributed largely to two important factors, namely an increase in secretarial fees of RI, 789 and an increase in the loss on the Journal from R2,343 to R3,508. In addition, our contribution to the expenses of the Federation of Societies of Professional Engineers increased by R607 from R549 to R1,156. The increase in secretarial fees is partly due to our increased demand for services and partly to increased salaries. In order to maintain its essential services it has been necessary for the A.S. & T.S. to increase salaries in order to keep pace with commerce and industry. With regard to the Journal, we did not expect immediate dramatic results from the changes that were effected as from the beginning of last year in the arrangements for publication. However, the improvement has been even slower in materialising than we expected. This situation is being watched carefully and we will not hesitate to make further changes if necessary. It became clear early in the year that the financial position was deteriorating and your Council decided that it was essential to meet the situation by raising subscriptions and entrance fees. At the same time it was decided that there are no grounds for a distinction between Town and Country members and that in future the scale for the compounding of subscriptions should be based on anticipated future membership, rather than past membership. These changes have had only a minor effect on the accounts under consideration. The MacArthur Forrest Memorial Fund shows an excess of income over expenditure of R132 and the total fund was, therefore, increased by this amount to R4,338. The balance sheet shows that the market value of quoted shares and debentures decreased during the year from R13,059 to R6,567, while accumulated funds now amount to R17,959 compared with R22,567 last year. It will also be noted that we are holding R25,844 on behalf of the Symposium on Opencast Mining. MEMBERSHIP Twenty-eight Fellows, twenty-four Members, seventeen Graduates, twenty-five Associates and twenty-seven Students were elected during the year. Four Members were admitted to Life Membership; Five Members were transferred to the grade of Fellow; one Student was transferred to the grade of Member; two Graduates and one Student were transferred to the grade of Member; six Students were transferred to the grade of Graduate; One Associate was transferred to the grade of Fellow; One Associate was transferred to the grade of Graduate. One Fellow, one Member, six Graduates, four Affiliates and ten Students were removed from the Membership Roll in terms of by-law 7.7.1. Your Council records with deep regret the death during the year, of the following: R. A. H. Flugge-de-Smidt, C. S. McLean, Dr H. J. van Eck, (Honorary Life Fellows), J. C. Humphreys, O. Lazar (Life Fellows), D. G. Beadle, J. G. Craig, P. U. Fisher, R. G. McConnell, J. H. Moore, S. Sterling, L. R. Ulyate (Fellows), H. H. Burger, E. A C. Dickson, R. Jack, S. Ring (Members), M. J. Worrall (Graduate). A comparative statement of the membership as at 30th June, 1970, and the end of the previous year is shown in the following tabulation: 30th June 30th June Honorary Life Fellows 10 8 Honorary Fellows 6 6 Life Fellows 189 191 Fellows 514 530 Members 448 465 Graduates 68 80 Associates 155 172 Students 162 161 1,552 1,613 RECLASSIFICATION OF MEMBERSHIP The designations of grades of membership were altered to accord with the practice in professional institutes both here and overseas and members were advised of the new classifications. MEMBERSHIP DRIVE A committee was established to organise a drive for membership as it was felt that there are numbers of persons in our mining and metallurgical industries who are not yet members but who qualify for membership. Members of the committee were allocated responsibility for campaigning in sections of industry and for publicising the aims, objectives and advantages of belonging to the Institute.

By D. A. Hayman, N. Rambuda, N. A. Sithole, C. Hockaday, J. D. Steenkamp

"Mogale Alloys operates two alternating current (AC) submerged arc furnaces (SAFs), and two direct current (DC) open bath furnaces. These furnaces are capable of producing two products, silicomanganese (SiMn) and ferrochrome (FeCr), with a total production capacity of 110 000 t/a. This paper focuses on the silicomanganese process specific to Mogale Alloys, with a two-furnace operation facility that produces 55 000 t of SiMn per annum.IntroductionMogale Alloys is situated in Krugersdorp in the West Rand District Municipality in South Africa’s Gauteng Province. The Krugersdorp facilities were initiated by Palmiet Chrome Corporation in February 1963 to produce charge chrome (Basson, Curr, and Gericke, 2007). Mogale Alloys bought the Palmiet Chrome facilities in 2005 from Samancor Chrome. The Afarak Group currently owns 90% of Mogale Alloys.SiMn is produced in two 20 MVA submerged arc furnaces (SAFs), which were originally built for chromite processing, and ferrochromium (FeCr) in two DC open bath furnaces rated at 40 MVA and 10 MVA. When this paper was compiled, the 10 MVA furnace was not operational due to the high cost of production, and one of the 20 MVA SAFs was recently converted to produce FeCr due to market constraints. Mogale Alloys has 290 permanent employees with four contracting companies on site. The paper presented here focuses on the production of SiMn at Mogale Alloys.The high-level process flow at Mogale Alloys is summarized in Figure 1, which details the raw material input and the products produced by the two 20 MVA furnaces. SiMn is produced by carbothermic reduction of manganese-bearing raw materials from four different sources, namely Wessels, Mamatwan, and UMK ores, and BHP sinter feed. The carbon sources are bituminous coal from Forzando and Msobo, local suppliers in Mpumalanga."

Nov 1, 2018

Alluvial diamond deposits covered with a thick overburden cannot be explored effectively and mined profitably with the available conventional techniques. A novel directional drilling technique has been developed and site trials have been conducted at the De Beers Namaqualand Mines situated at the western coast of South Africa. This paper describes the technique developed as well as the results of the site trials. The main task of the project is to develop a tool and a supporting system to achieve a remote exploration and ore extraction method for inaccessible alluvial diamond deposits. The project involves the acquisition of a system, commissioning on-site and evaluating the information obtained during assessment. The project consists of the design -of certain tools and instrumentation for the system, investigations and desktop studies as well as development of the system's logistics. The operating philosophy of the system is based on the keyhole surgery principle. In this study a pilot hole was drilled first, starting from the surface with an inclination to reach deeply seated diamondiferous gravel layers, followed by drilling into a more or less horizontal gravel layer for a certain length and finally pointing-upwards reaching ground surface at a predetermined exit point. The pilot drill bit was then replaced with a larger diameter reamer/mining tool and an HDPE tail pipe was attached behind the reamer. The drill string was retracted back to enlarge the guide hole and flush the excavated ore to the surface through the tail pipe. The material flow in between the sections of the system was' carefully measured to assess and record the gravel recovery rates. Several horizontal holes were drilled at preplanned drill paths to reach and follow the ore layer and the Ore extraction was achieved by means of a reamer/mining tool. Principles of the concept have been proven viable in this investigation.

Jan 1, 2010

By Johanna van Deventer, Sean Scott, Rene du Preez, Steven R. Izatt

In order to meet the stringent specifications associated with the production of LME Grade A cobalt cathode, producers need to ensure that a number of impurities, including Cd, are removed from the advance electrolyte to ppb levels (~0.1 mg/L). Conventional options include ion exchange using amino methyl phosphonic acid resin and solvent extraction using D2EHPA. More recently a Cd-selective resin, employing Molecular Recognition Technology (MRT), became available from IBC Technologies, Inc. These three potential unit operations were evaluated in parallel at Mintek. MRT was identified as the most technically feasible option. Results obtained on a cobalt advance electrolyte, containing 55 g/L Co, 6 mg/L Cd and 60 g/L Na2SO4, are presented in this paper.

Jan 1, 2007

By J. H. E. Perry, V. H. Wiik

"The ore deposits of the Zambian Copperbelt occur in sedimentary strata that have been subjected to relatively mild, flexure-type folding. Unrolling serves to reconstruct the original depositional geometry of the folded sedimentary strata and is in common usage on the Copperbelt both for geological analysis of drill hole data and in routine ore reserve estimation.A computerized method of unrolling was introduced at Roan Consolidated Mines in 1969 based on a standard contouring program. A contour map of the geological structure is drawn from a regular grid of elevations, interpolated from the original, irregularly-spaced intersections. Unrolling is performed across this grid, perpendicular to one or two axes specified by the geologist. Each intersection is unrolled independently, and the new co-ordinates are subsequently processed to produce unrolled maps.The technique has been used successfully at RCM over the last two years in both the estimation of ore reserves and exploration planning."

Jan 1, 2014

By S. Banisi, A. Ghasemi, E. Nematollahi

Discrete element method (DEM) has been used as a popular simulation method to verify designs by visualising how material will flow through complex equipment geometries. Although DEM simulation is a powerful design tool, finding a DEM model which includes real material properties (e.g., shape, cohesion and friction coefficients) is not computationally feasible. In order to obtain more realistic results, particle energy loss due to rolling friction has been highlighted by many researchers. To implement a reverse torque to account for rolling friction, various models have been proposed. On account of the complexity of the problem, there is no unique model for all applications (i.e. dynamic and pseudo-static regimes). In this paper, an in-house developed DEM software (KMPCDEM ©) was used to assess the robustness of three commonly used models by comparing the repose angle of iron ore pellets obtained through the draw down test in a laboratory setup and then the elastic–plastic spring dashpot model was modified based on considering the individual parameters instead of relative parameters of two contact entities. Results showed that the modified model could produce higher repose angle. The modified model was used to calibrate DEM simulation of repose angle of iron ore pellets in a laboratory setup of the draw down test. Comparison of the calibrated DEM simulation and laboratory results showed 2° differences between the predicted and measured angle of repose. This difference was attributed to considering the particle shape effects by assuming a spherical shape for particles. Keywords: DEM, rolling friction,particle shape, repose angle

Jan 1, 2020

By Jean Michel Marino, Jean-Pierre Slama

"The computer methods used by the French Commissariat a l'Energie Atomique, which are applicable to any type of ore deposits, are:(i) Ore reserve estimation. The data are either the core analyses or gamma leggings. To determine the spatial distribution of the ore, three different methods of interpolation are used. Two of these are based on the least-squares theory and the third one is an application of the regionalized variable theory. The interpretations of the orebody by the geologists are introduced in the computer program as often as possible.(ii) Optimal open pit design. From the spatial distribution of ore, the three-dimensional outlines of the optimal pit are determined by a geometrical algorithm which allows different slopes varying with the azimuth.Finally, the optimization of annual successive plans arc discussed."

Jan 1, 2014

By Karl-Heinz Obst, Juergen Stradtman

The importance of the chemical and physical properties of lime has been overlooked for years although the quality of lime plays an important role in the production of steel. With the introduction of the oxygen injection process these properties have been re-evaluated. The CaO, MgO, S, and P2O5 contents of lime are important, but so are the physical properties such as granulation, reactivity with respect to slag formation, and the degree of burning. Soft burnt lime enhances de-phosphorisation and de-sulphurisation, and facilitates the smelting process in general, mainly due to its large specific surface. Special lime, prepared as briquettes from quicklime and fluxes or as pellets from limestone and various fluxes with or without binding agents, clearly accelerates lime dissolution during the slag formation process, lowers the melting point, and enhances de-phosphorisation, de-sulphurisatlon, and de-carburisation even more than soft burnt lime. The introduction of special limes in the oxygen injection process for steel production has opened up new fields for commercial exploitation of slags as well as improved operational techniques.