Search Documents

By F. Lanaro, K. Röshoff, R. Christiansson, L. Jing

This paper presents the results of a project for developing a methodology for empirically determining some of the mechanical properties of the rock mass at the Äspö Hard Rock Laboratory, Southern Sweden. Using the equations available in the literature, the deformation modulus, friction angle, cohesion and unconfined compressive strength of the rock mass were estimated. A comparison of the results using different classification methods (Q, RMR, GSI, RMi, Ramamurthy’s) was made to estimate the range of variations in the mechanical properties with the considerations of: i) the quality/quantity of the geological data; ii) the technique for partitioning of the rock mass into homogeneous domains; iii) the sensitivity and subjectivity of the empirical methods; and iv) the need for validating the empirical methods against a test case. Cet article présente les résultats d’un projet visant à établir une méthodologie, pour déterminer, de façon empirique, les propriétés mécaniques de la masse rocheuse. En utilisant les corrélations disponibles dans la littérature, quelques-unes des propriétés de la masse rocheuse ont pu être déterminées (module de déformation, angle de friction, cohésion, force de compression illimitée). Une comparaison des résultats obtenus par différentes méthodes (Q, RMR, GSI, RMi, de Ramamurthy) a permis d’établir une échelle de variations des propriétés mécaniques et de formuler une série de recommandations concernant : i) la qualité/quantité des données géologiques ; ii) la technique de partition de la masse rocheuse dans des domaines homogènes ; iii) la sensibilité et la subjectivité des méthodes empiriques ; iv) la nécessité de valider les méthodes empiriques à l’aide de nouvelles études de cas. Dieses Paper präsentiert die Ergebnisse eines Projekts mit dem Ziel, eine Methodik für die empirische Festhellung von mechanischen Eigenschaften im Gesteinmassiv zu etablieren. Durch Verwendung der in der Literatur zugänglichen Korrelationen, wurden einige Eigenschaften des Gesteinmassivs festgestellt (Entstellungsmodul, Reibungswinkel, Kohäsion, unbeschränkte Kompressionsstärke). Ein Vergleich der Ergebnisse unterschiedlicher Methoden (Q, RMR, GSI, RMi, Ramamurthy’s) wurde durchgeführt und dies erlaubte die Feststellung der Variationsskala von den mechanischen Eigenschaften, sowie eine Reihe Empfehlungen für: i) Qualität/Quantität der geologischen Dateien; ii) die Technik für Teilung des Gesteinmassivs in homogene Domäne; iii)die Empfindlichkeit und Subjektivität der empirischen Methoden; iv) das Bedarf die empirische Methoden gegen neue Fallgeschichten zu validieren.

Jan 1, 2003

By A. E. Lewis, J. Du Plessis, J. Chivavava

Current metallurgical processes lack selective and efficient REE recovery from aqueous leach liquors. Antisolvent crystallisation is used to selectively recover pure inorganic salts from aqueous solutions without excessive chemical use in ambient conditions. Yttrium sulfate octahydrate (Y2(SO4)3.8H2O) was used as a representative rare earth salt to investigate the effect of antisolvent selection on the crystal morphology and size distribution of the final crystalline product produced through antisolvent crystallisation. The antisolvents of choice were short length alcohols that are water miscible i.e. methanol, ethanol, 2-propanol and t-butanol. All experimental parameters except the type of antisolvent were kept constant under isothermal conditions. The large reduction in solubility of the salt by the antisolvent creates high supersaturations. This leads to high product yields as observed in this study at > 91%. In general, a variety of morphologies were successfully formed in each individual alcohol including; rods, plates, prismatic cubes and starburst clusters. The powder X-ray diffraction (XRD) analysis indicated that Y2(SO4)3.8H2O was the only species present for all final products. There was a change observed from the starburst and rod structures for the shorter alcohols towards prismatic cubes for the longer alcohols due to different strengths in the solute-antisolvent interaction at the crystal growth faces. The crystal sizes increased with an increase in the alcohol chain length because of the lower supersaturation conditions due to a limit in the mass transfer induced by the bulkier alcohol structure. In conclusion, it has been shown that the particle morphology and size can be greatly affected by the selection of antisolvent even under high supersaturation conditions, contributing to understanding the effect of different antisolvents on the final particle characteristics. The engineering of favoured product characteristics can therefore be achieved by antisolvent crystallisation, presenting a viable alternative process for the recovery of REE. Keywords: Antisolvent crystallisation, rare earth elements, morphology, particle size

Jan 1, 2020

Fathi Habashi, Chalcopyrite. Its chemistry and metallurgy. New York, McGraw-Hill, 1978. 165 pp. RI9,95. Loss prevention and safety promotion The Proceedings of the 2nd International Symposium on Loss Prevention and Safety Promotion in the Process Industries, Heidelberg, 6th to 9th September, 1977, are now available. Chemical reaction engineering The Proceedings of the 4th International/6th European Symposium on Chemical Reaction Engineering (4th ISCRE) held at Heidelberg, Federal Republic of Ge rmany, from 6th to 8th April, 1976, are available from DECHEMA Deutsche Gesellschaft fur Chemisches Apparatewesen, P.O.B. 970146, D-6000 Frankfurt/ Main, West Germany, at the price of DMlOO plus postage and packing. Books received The Institution of Mechanical Engineers Proceedings Volume 190. Tribos abstracts on friction lubrication wear. Published by BHRA Fluid Engineering, Cranfield, Bedford MK 43 OAJ England. Price £30 (UK), US$72 (Europe), Seawater corrosion handbook, edited by M. M. Schumaker. Noyes Data Corporation Publicity Department, Mill Road at Grand Ave., Park Ridge, NJ 07656. 494 pp. Australian mineral industry quarterly 31(1) 1978 and 31(2) 1978. Bureau of Mineral Resources, Geology and Geophysics, Box 378, Canberra City, ACT 2601 Australia. Subscriptions $8, individual number $2. Mineral and NIM reports Report no. 1996 The extraction of gold from chloride solutions. (10th Nov., 1978). Report no. 1898 Batch and pilot-plant tests on M erensky Reef ore from the Western Platinum Mine. (8th Jun., 1977; reissued 30th Jan., 1979). Report no. 1920 A mineralogical investigation of Mamatu'an and Wessels manganese ores. (15th Sep., 1977; reissued 3rd Jan., 1979). Report no. 1978 The preparation and certification of a referencesample of magnetite ore. (22nd Dec., 1978). Report no. 1998 Electrode response to the addition of zinc during the cementation of gold. (25th Jan., 1979). Report no. 2002 The spectrochemical determination of phosphorus, magnesium, and iron in phosphate rocks and sulphuric acid leach liquors. (26th January, 1979). Report no. 1992 The use of emission spectrometry for the determination of impurities in metals. (24th Jan., 1979). Report no. 2003 An electrodeless conductivity meter of improved sensitivity and reliability. (28th Feb., 1979). Report no. 2005 The spectrometric analysis of manganese-bearing materials with particular reference to ferromanganese slags and metals. (16th Mar., 1979). Report no. 2006 An examination of procedures for the analysis of dry powders by atomic-absorption spectrophotometry. (28th Feb., 1979). Report no. 2007 The instrumentation and computerization of a 25 MV.A submerged -arc furnace. (25th Mar., 1977; reissued 16th Mar., 1979). Corrosion The International Corrosion Council has decided to hold the next Internat ional Congress on Corrosion in Mainz, Federal Republic of Germany, from 6th to 11th September, 1981. Process control The First European Symposium on Real -time Datahandling and Process Control will be held in West Berlin from 23rd to 25th October, 1979. Geomechanics The 28th Geomechanics Colloquy, organized by the Oosterreichische Gesellschaft fur Geomechanik, is to be held at Salzburg on 18th and 19th October, 1979. Geosta tistics A short course on 'Geostatistics for exploration and production planning' is being conducted by the Applied Earth Sciences Department, Stanford University, California, from 27th to 31st August, 1979. Business administration The Twelfth Executive Development Programme of the Graduate School of Business Administration, University of the Witwatersrand, is to be held from 9th July to 17th August, 1979. The engineer and the law A series of four meetings on the above subject is being conducted by the Measurement, Computation and Control SubCommittee of The South African Institute of Electrical Engineers. Lead smelter for South Africa? The National Institute for Metallurgy and Gold Fields of South Africa are making a comprehensive joint investigation of the technical and economic viability of an integrated lead smelter. Conference on titanium The Fourth International Conference on Titanium will be held from 19th to 22nd May, 1980, in Kyoto, Japan.

Jan 1, 1979

By D. Clement

A comparison between hydraulic and pneumatic rockdrills by D. CLEMENT The regulation of compressed-air reticulation systems is very poor compared with that of electrical systems; this means that electrohydraulic rockdrill systems offer greater flexibility, additional power being readily available at the working face. Hydrometallurgy A new journal devoted to all aspects of the aqueous processing of metals is scheduled to appear this year. Entitled Hydrometallurgy, the journal will be published in quarterly issues, one volume per year. Mineral dressing Contributions are invited for the Symposium on Recent Progress in Mineral Dressing in South Africa, which is to be arranged jointly by the South African Institute of Mining and Metallurgy and the National Institute for Metallurgy. Mineraalbereiding Bydraes word verlang tot die Simposium oor Onlangse Vordering met Mineraalbereiding in Suid-Afrika wat gesamentlik deur die Suid- Afrikaanse Instituut vir Mynbou en Metallurgie en die Nasionale Instituut vir Metallurgie gereel gaan word. Rock mechanics The Sixteenth Symposium on Rock Mechanics is to be held at the University of Minnesota from 22nd to 24th September, 1975. The Symposium is the official Symposium for 1975 of the International Society for Rock Mechanics (I.S.R.M.), and the Council for I.S.R.M., consisting of members from 25 countries, will meet during the Symposium. Powder metallurgy The annual meeting on powder metallurgy organized by The Metals Society is this year to be held at the Stratford Hilton Hotel, Stratford-upon-Avon (the notification did not include the date of the meeting). Vacation School The South African Institute of Mining and Metallurgy has great pleasure in announcing its intention of holding a vacation school on the topic of electric-furnace melting. NIM reports Report no. 1681 The determination of sulphur and phosphorus in chromite. Report no. 1687 The viscosities and electrical conductivities of slags associated with the production of high-carbon ferromanganese alloys.

Jan 3, 1975

By G. Jandieri

An improved methodology is presented for assessing the economic feasibility and effectiveness of recycling industrial waste. The methodology is based on the break-even control mechanism, but at the same time provides for the introduction of new evaluation criteria such as the threshold of conditionality and the degree of ore substitution. Based on an improved analysis, it becomes possible to more precisely predict recycling efficiency. A more refined determination of the lower limit of concentration of recoverable metals, at which technogenic waste can be assigned the status of secondary raw materials and processed profitably, leads to a significant expansion of the secondary raw material base suitable for recycling. The potential for recycling manganese-containing dust from the production of ferrosilicomanganese, dehydrated sludge from the hydro separation of slags, and cake from the production of electrolytic manganese dioxide at the Chiatura mining enterprise is used as an example. It is shown that with a threshold of –24% Mn content, the highest recycling efficiency can be achieved by the production of low-phosphorus manganese slag and conversion to ferrosilicomanganese using the above waste to replace 40-60% grade III and IV manganese concentrates in the feed.

Jan 26, 2023

[The following notations will be used: O an ore body. W a sample of size w located in O; the size of this sample. W a block or a sample, of size W, located in O; the size of this block or sample. z' a point in W. W' a block or a sample, of size W' greater than or equal to W, located in O; the size of this block or sample. z" a point in W'. y (h) point semivariogram in O. s (h) point covariogram in O. In the previous chapter, we saw that the point semivariogram y (h) usually cannot be estimated directly from the data available. Rather, the values of samples of size w are available in O, and from these a regularized semivariogram y w (h) can be estimated. The following relationship has been proved (5.8): Y w(h) = Y (w;w+h) - Y (w;w). y (w;w+h) is the average value of y (z' z") when z' takes all possible positions in a sample w and z" all possible positions in a sample w+h of the same size, h being the distance between w and w+h. y (w;w) is the value of y (w;w+h) for h = 0, i.e. the average value of y (z' z") when z' and z" take all possible positions in w. We also saw that the regularized covariogram aw(h) is related to the point covariogram a (h) as follows (5.9): w(h) Gr In the following chapters, it will be shown that calculation of the average value y of y, or -a of a, in the general case relating to samples or blocks W and W' which need not be of the same size, plays a very important part in all the practical applications of geostatistical theory. The purpose of this chapter is to introduce various methods of calculating y and a-. Furthermore, mathematical equations and graphs are provided which can be used when the point semivariogram can be represented by one of the more common equations, and when the blocks W and W' are of simple shape. By definition (Fig. 6.1): [ ] Y (W;W) = WW f dz' f y (z' z") dz" (6.1) in W z" in W']

Jan 1, 1978

By G. Poropat, A. R. Guest, H. P. Grobler

At the De Beers Consolidates Mines operations it is common practices to perform Geotechnical mapping of the newly exposed faces in the waste and ore rock. The purpose of Geotechnical mapping is to quantify the in-situ fracturing of a rockmass that in turn is required during the planning and application of a mining method. Whether it is to determine slope angles, caveability, impact of blasting or support requirements. This mapping involved a cumbersome and time consuming procedure that requires individual examination and description of the natural inherent fractures exposed by mining. During highwall mapping in an open pit this can be a safety concern due to the duration of time spent below a highwall. The advantages gained through the recent introduction and application of SiroVision® allows safer mapping, an increase in statistical fracture population, archiving of rock faces and the more accurate reflection of the true mapping. This paper aims to describe in detail the application of the recently developed SiroVision®, photogrammetry software, to replace conventional face mapping. A De Beers Consolidated Mines, il est pratique courante de faire une cartographie géotechnique des tailles récemment exposées dans le rocher stérile ou minerai. Le but de la cartographie géotechnique est de quantifier la fracturation in-situ d’une masse rocheuse, qui sera nécessaire lors de la planification et application d’une méthode minière, que ce soit pour déterminer les angles des galeries inclinées, les possibilités de foudroyage, l’impact du dynamitage, ou les besoins en supports. Cette cartographie nécessitait une procédure longue et compliquée qui demande l’examen individuel et la description des fractures naturelles propres exposées par l’opération de mine. Pendant la cartographie de parois dans une exploitation à ciel ouvert, cette opération peut être dangereuse à cause du temps passé sous la paroi. Récemment, le lancement et application de Siro Vision apportent l’avantage d’une cartographie plus sûre, une augmentation des statistiques de population de fracture, l’archivage des tailles de roches, et le reflet plus précis de la cartographie. Le but de l’étude présente est de décrire en détail l’application du développement récent de Siro Vision, logiciel de photogrammétrie, pour remplacer la cartographie de taille conventionnelle. Bei den De Beers Consolidates Mines Operationen ist es gängige Praxis geotechnische Aufzeichungen des Taub- und Erzgesteins neu geöffneter Abbaustellen zu erstellen. Zweck dieser geotechnischen Aufzeichnungen ist die vor-Ort-Quantifizierung des Bruches der Gesteinsmasse, welche im Gegenzug während der Planung und der Anwendung einer Abbaumethode erforderlich ist, sei es um einen Neigungswinkel festzustellen, Abbaubarkeit, Auswirkung von Sprengungen oder Anforderungen an Unterstützungen. Die Aufzeichnungen waren mit umständlichen und zeitaufwendigen Prozeduren verbunden, die eine individuelle Prüfung und Beschreibung der durch den Abbau freigelegten natürlichen inhärenten Brüche, verlangten. Dies kann auf Grund des Zeitraumes der unterhalb einer Flözoberschicht verbringt wird zu einer Frage der Sicherheit werden wenn die Aufzeichnung einer Flözoberschicht im Tagbau erfolgt. Die Vorteile auf Grund der jüngst erfolgten Einführung und Anwendung der SiroVision® gestatten sichereres Aufzeichen, eine Zunahme in der statistischen Menge an Gesteinsbrüchen und eine akkuratere Reflektion der tatsächlichen Aufzeichnungen. Diese Arbeit hat zum Ziel im Detail die Anwendung der kürzlich entwickelten SiroVision®, eine photogrammetrische Software, die die konventionelle Abbauortaufzeichnung ersetzen soll zu beschreiben.

Jan 1, 2003

By Z. G. He, S. H. Chen, P. Egger

A new model for hollow rock bolts which comprises rock material, hollow bolt material, bolt/rock interface, is developed on the base of the composite element method (CEM). The main advantage of the new model is that it can be incorporated into the conventional finite element analysis. So the mesh generation of bolted rock structures becomes more convenient and feasible, which is very important in the optimisation of reinforcement design: the mesh can be kept unchanged when the number and orientation of bolts are adjusted. The comparison of the calculation results with a conventional FE approach shows the robustness of the proposed method. Un nouveau modèle numérique de boulons creux comprenant la roche, le matériau du boulon creux et l’interface roche / boulon est développé sur la base de la méthode des éléments composites (CEM). L’avantage principal du nouveau modèle est la possibilité de l’incorporer dans une analyse aux éléments finis conventionnelle. Ainsi la génération du maillage d’une structure rocheuse ancrée devient plus simple ce qui est très important pour une optimisation du projet : en cas d’ajustement du nombre et de l’orientation des boulons, le maillage reste inchangé. La comparaison de résultats de calcul avec ceux obtenus par un code aux éléments finis conventionnel montre la robustesse de la méthode proposée. Auf der Grundlage der Verbund-Element-Methode (CEM) wird ein neues Modell für hohle Reibungsanker entwickelt, das den Fels, das Ankermaterial und die Kontaktfläche Fels / Anker umfasst. Der Hauptvorteil des neuen Modells ist die Möglichkeit, es in eine konventionelle FE-Analyse einzubetten. So wird die Netz-Generierung für verankerte Fels-Bauwerke einfacher, was für die Optimierung des Verankerungs-Projekts von Wichtigkeit ist: wenn Zahl und Orientierung der Anker variiert werden, bleibt das Netz unverändert. Der Vergleich von Rechenergebnissen mit solchen aus einer konventionellen FE-Rechnung zeigen die Robustheit der vorgestellten Methode.

Jan 1, 2003

By L. Petzold

The demand for stainless steel is ever-increasing. As an essential element in stainless steel-making process, so is the demand of chromite concentrate. At the same time, the industry proven technologies for beneficiation of chromite are limited. Chromite is only crushed, screened and jigged to produce a concentrate. However, for ultrafine and low-grade material, no satisfactory beneficiation methods for the enrichment of chromite fines exist in industrial operation. This poses a clear challenge for the industry, which Primetals Technologies has addressed with the development of a new beneficiation process. The aim of this process was to enrich low grade chromite tailings to a quality suitable for the smelting process. Required concentrate grades are different over the world, concentrate grades of Cr2O3=40% and lower are found at the Bushveld Complex, South Africa. The target for the present study was a Cr2O3-grade in the area of 49%. Three different chromite tailings with Cr2O3 grades between 16 % and 29 % were part of a study, executed by Primetals Technologies. All three tailing materials were characterised by Mineral Liberation Analysis (MLA). Based on the physical, chemical and mineralogical findings, process flowsheets were developed. The process flowsheets included grinding to ensure a full liberation of the chromite. The liberated material was classified at a cut size of 63 μm to a coarse and fine fraction. Gravity separation and flotation processes were tested with the coarse particle fraction. Due to the limitations of gravity separation with fine particles, only the flotation process is suitable and was tested with the fine fraction < 63 μm. A Design of Experiment (DoE) with six factors, each three levels, was conducted to identify optimal parameters for the fine chromite flotation. Two different collectors were tested: a phosphoric acid ester and a fatty acid type collector. In small scale test work a chromite concentration suitable for the smelting process was achieved. On this basis Primetals Technologies will develop a pilot-scale test program to research recirculation effects and upscale potential of the process. Keywords: Mineral processing, tailings beneficiation, flotation, density separation, process development, chromite

Jan 1, 2020

By B. P. Watson, A. Carpede, W. O. Kekana, N. Fernandes, W. Theron, M. P. Mahlangu, G. Betz

The research described in this paper was done to confirm the Upper Group 2 (UG2) PlatMine peak pillar strength formula (Watson et al., 2007), which was determined from a back-analysis of failed and unfailed pillars. Underground measurements were made on a stable pillar that was loaded by firstly reducing it’s length and then by mining the surrounding pillars until pillar failure took place. The pillar was instrumented with suitably positioned strain cells and closure meters, which allowed both the average pillar stress and strain to be determined. The paper describes the methodology applied to identify a suitable position for the instrumentation, as well as the results. A stress/strain curve is presented for a UG2 pillar with a w/h ratio of 2.0, at Booysendal Platinum Mine. The measured pillar strength was similar to the predicted strength using the PlatMine pillar strength formula for UG2 pillars. The PlatMine formula has been successfully implemented on Booysendal Platinum Mine, and about 3 670 pillars have been cut without a single failure. An additional revenue of US$1.3 billion was calculated for the 25-year life of the mine as a direct result of the improved pillar design, given the January 2020 platinum group metals basket price. An extended life of mine and better mining efficiencies will also be realized.

Aug 1, 2021

By A. Tosun

Muckpile fragmentation formed by blasting depends on the specific charge factor, the discontinuities in the rock mass, and the rock strength. Determination of the discontinuity characteristics and rock strength is a long and difficult process. These two parameters are directly associated with the rock drilling speed. Therefore, it is the drilling speed of the machine used for the blast-hole, rather than the blasthole discontinuity characteristics and rock strength parameters, that is used in the prediction of muckpile fragmentation before blasting. Primarily, it has been suggested that the muckpile fragmentation values can be correctly determined by establishing correlations between the efficiency of the loader and muck pile fragmentation, since fragmentation is directly correlated with the former parameter. Subsequently, a correlation predicting the drilling speed of the drill machine was developed according to the discontinuity characteristics of the blasting surface and the rock strength. Finally, a correlation was developed predicting muckpile fragmentation according to the specific charge factor and the drilling speed of the drill machine The data was obtained by conducting blasting tests in two different limestone quarries.

Nov 30, 2022

By Marek Dworzanowski

Dense medium separation (DMS) is critical to the operation of coal and diamond beneficiation plants. It is also utilised in iron ore, manganese, chromite and andalusite beneficiation as well as pre-concentration for platinum-bearing UG2 ore. Gravity concentration plays an important role in the processing of diamonds, coal, gold, platinum, titanium minerals, zircon, chromite, iron ore and manganese. The DMS and Gravity Concentration operations and technology in South Africa conference will focus on the operation of DMS and Gravity Concentration circuits in the South African Mining Industry. The current status of the technologies and equipment employed will be presented as well as future developments. The conference was set up to showcase South African DMS and Gravity Concentration operations and provide a forum where operators, technology and equipment suppliers can engage in knowledge sharing. The papers cover a wide spectrum of topics, including descriptions of operations, optimisation projects, new capital projects, equipment applications, process monitoring and process selection. Most commodities and unit processes associated with DMS and Gravity Concentration are covered. The conference venue was selected to be the CSIR Convention Centre in Pretoria. The CSIR has contributed to DMS research in South Africa and it is located not far from many coal, diamond, gold, platinum and chrome mines that extensively utilise DMS and Gravity Concentration in their beneficiation plants. I believe that the papers and presentations submitted for this conference will provide a valuable future reference for DMS and Gravity Concentration, thus making the work of all the contributors to this conference highly rewarding and worthwhile.

Jan 1, 2006

By M. Seerane, R. Machaka, P. Ndlangamandla

"Metal injection moulding (MIM) is a near-net-shaping powder metallurgy technique suitable for the cost-effective mass production of small and complex components. In this paper, the effects of the metal powder particle size on the final properties of 17-4 PH stainless steel are reported. Three different particle sizes (d50 33.0, 7.91 and 4.04 µm) were used to prepare the injectable MIM feedstocks using a CSIR-developed wax-based binder system at a fixed solids loading of 60 vol.%. The distribution slope parameter and the rheological flow index behaviour were used to predict the flowability of the feedstocks. The effects of the particle size on MIM products were established. The results are discussed in terms of the subsequent microstructural and mechanical properties of MIM 17-4 PH stainless steel against the established MPIF Standard 35. IntroductionMetal injection moulding (MIM) is a near-netshape manufacturing process established as an alternative to produce complex small-tomedium shaped components that were previously fabricated by conventional methods at higher costs (Attia and Alcock, 2011; Todd and Sidambe, 2013).Although recent advances in micromanufacturing (mainly machining and electrodeposition-based) have enabled the fabrication of complex micro-size geometries directly into miniaturized parts, these processes are generally neither routine nor easily accessible at present (Attia and Alcock, 2011).Typically, the MIM process consists of four steps: mixing, injection moulding, debinding and sintering. Mixing involves blending of the desired metal powder composition with carefully selected multicomponent organic binders at the right proportion. This mixture, which is called feedstock, is then injected into a mould of a required shape to form a ‘green part’. Debinding is the removal of the binders by chemical, thermal, or catalytic means while maintaining the shape of the part. Finally, the debound part is sintered to a full or near-full density part (Sotomayor, Varez and Levenfeld, 2010). The MIM process is essentially a combination of plastic injection moulding with conventional powder metallurgy technologies."

Jan 1, 2016

By E. Maritz

"The localized uniform conditioning (LUC) technique was proposed by Marat Abzalov in 2006. The technique converts conventional uniform conditioning (UC) grade-tonnage curves into single grade values attached to each smallest mining unit (SMU). This is achieved by ranking the SMUs within a panel in increasing order of their grade (based on the direct kriging of SMUs). This ranking is then used to localize the conventional UC grade-tonnage curves for each panel by dividing them into classes and computing their mean grades, which are assigned to the SMUs. The quality of this localization process will depend heavily on the validity of the grade patterns predicted by the direct kriging of the SMUs. Abzalov noted that where the distribution of data available for the direct kriging of the SMU is characterized by strong short-range variability, the advantages of using the LUC approach may be more limited. Consequently, a study was undertaken to determine how valid the predicted grade patterns of a typical Birimian-style gold deposit (with high nugget effect and strong short-range variability) might be expected to be. This was determined by comparing the direct SMU kriging ranking (based on sparse data) with the grade control model ranking (based on close-spaced data and the best available estimate of the deposit). The results showed a satisfactory correlation between these rankings and it was concluded that, although the grade patterns predicted by the direct kriging of the SMUs may be less meaningful for deposits exhibiting strong short-range continuity, there is nevertheless a convincing relationship with the actual (or best available) rankings. Therefore, the LUC technique is still considered to be useful for this style of deposit. IntroductionFor adequate technical and financial evaluation of a project, attempts should be made to estimate the recoverable resources – the portion of the in situ resource that can be economically extracted by mining. To achieve this, the estimates of the tonnage and grade of the mineralization should be produced above a given economic cut-off and should take into consideration the proposed mining selectivity."

Jan 1, 2016

By M. A. Mahboob, T. Celik, B. Genc, I. Atif, S. Ali

"Mapping of hydrothermally altered areas, which are usually associated with mineralization, is essential in mineral exploration. In this research, open source reflectance spectroscopy data from the multispectral moderate-resolution Landsat 8 satellite was used to map altered rocks in the Gauteng and Mpumalanga provinces of South Africa. The unique spectral reflectance and absorption characteristics of remotely sensed Landsat data in the visible, near-infrared (NIR), shortwave-infrared (SWIR) and thermal infrared (TIR) regions of the electromagnetic spectrum were used in different digital image processing techniques. The band ratios (red/blue, SWIR 2/NIR, SWIR 1/NIR), spectral band combinations (Kaufmann ratio, Sabins ratio) and principal component analysis (Crosta technique) were applied to efficiently and successfully map hydrothermal alteration minerals. The results showed that the combination of spectral bands and the principal component analysis method is effective in delineating mineral alteration through remotely sensed satellite data. The validation of results by using the published mineral maps of the Council for Geoscience South Africa showed a good relationship with the identified zones of mineralization. The methodology developed in this study is cost-effective and time-saving, and can be applied to inaccessible and/or new areas with limited ground-based knowledge to obtain reliable and up-to-date mineral information.IntroductionMany developing nations depend on exploration and exploitation of mineral resources to sustain their economic growth. Usually, the traditional mineral exploration techniques require enormous finances, prolonged time, and tremendous manpower, particularly in areas that are not easily reachable (Maduaka, 2014). Furthermore, mineral exploration required state-of-the-art techniques and expertise along with geological, geochemical, and geophysical datasets, which may not be easily available or may be lacking where access is problematic (Kaiser et al., 2002; Bemis et al., 2014). Modern remote sensing technology has proved to be one of the highly efficient and robust techniques used for mineral exploration. The use of remote sensing satellite images for geological mapping and mineral exploration usually involves studying the physicochemical properties of rocks and weathering soils, such as mineralogy, landforms, geochemical signatures, and the spatiall distribution of lineaments (Bhattacharya et al., 2012)."

Mar 1, 2019

I. Book review Legal and institutional arrangements in minerals development. Edited proceedings of a workshop organized jointly by the VN. Department of Technical Co-operation for Development and the German Foundation for International Development (DSE), held in Berlin in August 1980. London, Mining Journal Books, 1982. Soft, 228 X 149 mm, xi + 223 pp. Approx. R30 + GST. Reviewer: M. J. Martinson 2. New books Strength of metals and alloys (IOSMA 6). R. C. Gifkins (Editor). New York, Pergamon, 1982. Approx. 1200 pp. 3 vols. V.S. $220. Deformation-mechanism maps. The plasticity and creep of metals and ceramics. H. J. Frost and M. F. Ashby. New York, Pergamon, 1982. Approx. 250 pp. V.S. $60. Pressure diecasting, Part 2. The technology of the casting and the die. D. F. Allsop and D. Kennedy. New York, Pergamon, 1982. $ V.S. 27.50.

Jan 1, 1982

By K. J. Craig, M. A. Swart, Q. G. Reynolds, L. Hockaday

A solar reflector soiling study was carried out at a ferromanganese smelter in South Africa to assess the soiling rates at different locations around the plant. Several meteorological parameters were monitored to give insight into the conditions that lead to increased soiling. Mineralogical characterization of dust samples collected from the reflectors and the atmosphere revealed that only a certain size fraction is of importance with regard to soiling, and that the dust can be attributed to both raw materials and smelter products. Proximity to the dust source was the primary driver for increased soiling. The site that experienced the most soiling was very close to raw material heaps; this was deemed an outlier and was excluded from the summary statistics. The secondary driver for increased soiling was location relative to the smelter dust sources and the wind’s direction and speed. The reflector set at the best location experienced 13.1% less soiling than the set at the ‘worst’ (but still feasible) location, represented by an averaged mean daily reflectance loss of 0.0186. The study revealed that while there are periods of intense soiling at this particular site, proper planning of reflector location in relation to the smelter dust sources can significantly mitigate the soiling rate.

Jun 5, 2023

By A. Chryssoulis, D. Venter, R. Dunne

An often-overlooked parameter of flotation processing is the impact of surface chemistry. Flotation processing, being a heterogenous process is largely reliant upon the chemistry occurring at the interfaces between solid-liquid phases. Development of analytical techniques such as Auger electron spectroscopy, X-Ray photoelectron spectroscopy (XPS) and low energy electron diffractions (LEEDS) has allowed for a dynamic view characterizing surface composition and structures. The advent of ‘static’ systems, capable of measuring ultra-thin layers on surfaces at low concentrations, was the next step in surface analytical developments. In general, it is the low concentrations and fragmentation patterns which limit the analysis of certain chemical species at plant concentration ranges. At present, analysis of inorganic and organic surface modifiers by time of flight mass spectrometers with a variety of ionization techniques has become a common analytical method to measure chemical species on the outermost surface of mineral particles. By studying the relationship between surface analysis results with metallurgical outcomes, the implications of the presence of surface species can be determined. The presence of flotation activators or depressants can be established using Laser Ionization Mass Spectrometry (LIMS) and Resonant Ionization Mass Spectrometry (RIMS) which are highly versatile surface sensitive analytical techniques. A case study applied to sphalerite flotation in the Neves Corvo Cu-Pb-Zn concentrator and the implication inorganic surface modifiers have is presented. By determining the relative concentrations of Cu, Pb, oxidation products, Ca and other surface species in floated and rejected mineral particles, rationale for improving recovery and selectivity is elucidated. Keywords: Cu-Pb-Zn Flotation, Process Mineralogy, Surface Chemistry, Flotation kinetics

Jan 1, 2020

By M. Rhodes

The Sukari project, which is owned by Centamin Egypt Ltd, is located in southern Egypt, 770 km south of Cairo but close to the Red Sea. The project is the first new gold development in Egypt and was commissioned in the middle of 2009. In 2007, Centamin purchased the CIL plant from the Kori Kollo mine in Bolivia. This plant was originally designed to treat 6.5 Mtpa of oxide ore. The Sukari deposit contains an oxide zone close to surface with a thick zone of mixed oxide and sulphides below this. The sulphides contain relatively coarse pyrite and arsenopyrite with fine <10 µm gold inclusions. Eventually, the sulphide ore will be mined from underground. Metplant Engineering Pty Ltd, a subsidiary of Bateman Engineering Pty Ltd was contracted to design modifications and additions to the Kori Kollo plant to enable it to treat the Sukari ores. The plant was designed to treat the three ore types in stages. Throughput was set to 4 Mtpa, dueto Sukari ore being harder, at a head grade of 1.7 g/t to produce 200 000 oz of gold. The oxide circuit was based on the use of the Kori Kollo plant and the difference with mixed ore was that the oxide circuit would treat flotation tailings rather than ore. This circuit has a leach capacity of 26 000 m3 and residence time of 24 hrs The main feature of the upgraded mixed ore plant was the addition of a flotation circuit to produce a concentrate which would be reground and treated in a separate leach and elution circuit. Ore is crushed in a gyratory crusher and the comminution circuit uses a conventional SABC producing a product with a P80 of 150 microns. The throughput of 580 tph of oxide ore and 500tph of mixed ore was set to match the mills from Kori Kollo, with the addition of the pebble crusher to accommodate the more competent Sukari ore. The flotation circuit comprises a single rougher circuit to maximize recovery. The concentrate is thickened prior to regrinding which is carried out in a tower mill and two SMD mills operating in series. The final product, with a P80 of 12 microns, from the regrind circuit is leached in a CIL circuit with a total capacity of 2 550 m3. Gold is recovered through a conventional pressure Zadra circuit. Tailings from both circuits report to separate tailings thickeners and are pumped to a tailings storage facility. The circuit is designed to maximize the recovery of water. The project lies in one of the driest deserts in the world and a feature of the operation is the use of sea water from the Red Sea. This water is pumped 25 km from the coast.

Jan 1, 2009

By T. H. Yang, Q. K. Wang, T. Song, J. W. Zhou

The grinding circuit can be one of the most important mineral processing circuits in plants. Along with the application of large-scale milling machines, the design and optimisation of the operation strategy for grinding circuits is more complicated. An in-house grinding process simulation tool was developed to mass balance, model fit and simulate crushing, grinding and classification circuits. An industrial grinding and classification circuit in a copper mine was modelled, and the modelling parameters were verified by a particular group of plant survey data. To justify the prediction ability of the fitted models, the model predictions under different operation conditions were compared with another group of plant survey data. Then the model predicted the effects on the circuit of changing operating conditions. Circuit analysis of the comminution process for water feed to a SAG mill, water feed to sump, the rolling speed of a SAG mill and the percentage of ball filling in a SAG mill was put into practise, based on the simulation results. The simulation results can be used to help plant operators understand the features of the comminution process and may help to build a knowledge library for process control. Keywords: Process modelling, grinding, comminution, circuit analysis

Jan 1, 2020