Search Documents

By I. Çinar

Cappadocia is not only a region of Turkey with historical and touristic importance. During the cutting and processing of volcanic tuff, quarries in this region release large amounts of tuff into the environment that is viewed as waste. The release of this waste constitutes an economic loss and contributes to environmental pollution. However, through experimentation with deformation, weight per unit of volume, water absorption, uniaxial compression strength, modulus of elasticity, and point load strength index, volcanic tuff and marble dust composite materials can be produced for use in the building sector. In this study it was observed that, as the percentage of volcanic tuff dust in the mixture increased, the water absorption rate of the material increased, and uniaxial compression strength and point load strength decreased. The produced composite samples used in this study were kept for a predetermined number of times per day, and no deformation in the surface characteristics of the materials was observed. In a statistical parameter analysis, averages, variances, standard deviations, coefficients of variation, and skewness coefficients were calculated. Covariance changes between experimental parameters were also determined. In this study, two types of volcanic tuff dust, that is, yellow and red, were produced during the production of tuff-marble dust composite material. When the percentage of either type of volcanic tuff dust was increased, an increase in water absorption was observed. It was also observed that when the percentage of volcanic tuff dust was increased, uniaxial compressive strength and point load strength decreased. Furthermore, the physical and mechanical properties of the materials obtained by mixing different colored tuff powders and marble powders in different proportions were evaluated using statistical parameter analysis.

Mar 5, 2025

By J. Githiria, D. Wachira

The conventional truck and shovel haulage system has become expensive to operate in most mines due to current strict environmental conditions, increase in depth and size of open-pit mines, increase in labour costs, and fuel costs. These factors have motivated the search for alternative material haulage options in open-pit mines. In-pit crushing and conveying (IPCC) system has been regarded as a plausible alternative in material haulage systems. However, usage of IPCC has been limited to a few mines due to limited knowledge of IPCC performance, and other technical factors of the system. This paper investigates, and evaluates the productivity performance of four types of IPCC systems (fixed, semi-fixed, semi-mobile, and fully mobile IPCCs) using mine productivity index (MPi). Using a model developed by MATLAB, the MPi for the four systems is computed using input variables such as availability, utilisation, performance and number of trucks and shovels in a limestone quarry. The mine productivity index for fixed, semi-fixed, semi-mobile, and fully mobile IPCC is obtained as 67.13%, 69.02%, 70.52%, and 71.52% respectively. In conclusion, the fully mobile in-pit crushing and conveying system is the most appropriate IPCC in the quarry, due to its better productivity performance compared to the other three IPCC systems and the truck and shovel system currently in use.

Sep 1, 2021

By E. Matinde

Human beings have been dependent on metals and alloys for livelihoods since time immemorial. In fact, there is irrefutable evidence that successful ancient civilizations achieved supremacy over their environments through the mastery of metals and alloys (Miller, 1995; Mtetwa, 2022). Over time, metals and alloys have evolved to become ubiquitous engineering materials indispensable to mankind, with applications in industrial and residential infrastructure, agriculture, energy generation and storage, transportation and communication systems, and manufacturing, among others (Elshkaki et al., 2018; Watari et al., 2021). Population growth, technological developments, and increase in urbanization and industrialization are all intricately linked to the intensity of use of metals and alloys. With up to 5 billion people estimated to live in urban areas by 2030 (Armstrong, 2009), the demand for metals and alloys will inevitably increase in order to satisfy the increased demand for infrastructure, machinery, and other human needs (Elshkaki et al., 2018; Watari et al., 2021). According to LePan (2022), urbanization and growth of mega-cities will increase the demand for metals and alloys, such as nickel, steel, aluminium, and copper by 116%, 50%, 57%, and 26%, respectively, between 2019 and 2035. Naturally, the production of metals and alloys from natural ores, secondary resources, and/or a combination of both, to meet this increased demand will invariably lead to the increase in generation of deleterious emissions in the form of wastes. In fact, mining and metallurgical wastes currently constitute the world’s largest anthropogenic streams by mass, often containing a high concentration of elements and compounds that can cause potential damage to natural ecosystems and humans (Hudson-Edwards et al., 2011; Lottermoser, 2011; Matinde et al., 2018; Seetharaman et al., 2022). Obviously, society’s heavy reliance on new mineral resources to drive the emerging energy transition entails that the legacy of these waste streams will continue unabated for the near-foreseeable future. The scarcity of high-grade mineral reserves, coupled with deliberate efforts to solve the anthropogenic circularity conundrum, therefore introduces a high level of urgency in the metal extraction industry to develop nascent and more eco-friendly processes and technologies. Integrating circular economy principles based on intentional configurations of circular industrial ecosystems in order to maintain the value of materials and resources in the economy for as long as possible is widely accepted as a practical approach to mitigating the negative externalities imposed by

Sep 1, 2024

By M. Fener, S. Kahraman, O. Gunaydin, M. Alber

Falling into the weak rocks category, fault breccias have extremely poor engineering properties. These pebbles typically cause issues with slopes, subterranean construction, and building projects. Professionals will benefit from the creation of some predictive models for fault breccia triaxial strength, as smooth specimen preparation is typically challenging and timeconsuming. The purpose of this study is to develop some predictive models for the differential stress (Δσ) based on physical and textural properties. Artificial neural networks were used to analyse data related to Misis fault breccia. Initially, models with moderate (noticeable, but not good) correlation coefficients were created using multiple regression analysis. After that, the regression models and three distinct artificial neuron network models were contrasted. Regression models are weaker and less trustworthy than artificial neuron network models, as demonstrated by this comparison. Pointed out is the practicality and ease of use of the artificial neuron network model with S-wave velocity and volumetric block proportion. Ultimately, it can be concluded that artificial neuron networks analysis provides a reliable indirect method for predicting the differential stress of Misis fault breccia.

Sep 1, 2025

"The management of outlier grades in positively skewed gold distributions is a contentious issue. Incorporating outliers in standard ordinary kriging (OK) estimation procedures in a way that honours the data without smearing extreme grades into surrounding areas has been problematic. Cutting or capping of outliers to mitigate their influence in estimation techniques is common practice, while methods that manipulate the OK system of equations fail to honour the data. We propose a method of post-processing of kriging weights that provides realistic OK estimates and mitigates smearing without manipulating kriging equations or changing the original grades. The method requires that the data is not clustered, is approximately equally spaced, and is of the same support. Positively skewed data is ordered on attribute grade and nonlinearly transformed to a Gaussian histogram of categorical bins whose frequency is based on their likelihood of occurrence and location in the sample distributions. Factors that restrict kriging weights are calculated by dividing the percentage frequency of data in each bin by the percentage frequency of data in the bin with the highest frequency. Restriction factors applied to the kriging weights in the OK estimation restrict the range of influence in proportion to their probability of occurrence in the distribution. Smear reduction post-processing is easy to implement and addresses issues arising from negative kriging weights while considering the spatial location of samples, the sample grades, and their probability of occurrence. The method mitigates both smoothing and conditional bias.IntroductionOutliers are sample observations that deviate considerably from the standard or expected (Hawkins, 1980). These deviations can be high or low in grade depending on the distribution. The presence of outliers in a mine sampling campaign could provoke mixed reactions. Mining engineers might view high-grade outliers as a promise of achieving higher grades, while the geostatisticians view outliers as affecting the accuracy and precision of the overall estimate, among other issues. Having identified outliers, the geostatistician must decide how to account for their presence and treat them so that true underlying estimates are not distorted. Advanced knowledge of the deposit allows the geostatistician to identify and treat outliers acceptably, especially where samples are limited in number and the true grade distribution is uncertain. If ignored, or treated incorrectly, outliers are likely to lead to smearing of extreme grades into the surrounding estimates, thereby steering regions towards potential under- or over-estimation."

Apr 1, 2019

By A. K. Raji, M. O. Ojumu

Robotic subsea dredging crawlers are dynamically and remotely controlled vehicles that are used for deep sea mining and recovery operations. These exploration machines are released from a mother ship and move around on the ocean floor using tracks. Current ocean crawlers such as the MK3 ROST are hydraulically powered. In this paper we develop a scaled-down model for simulating and performing static loading analysis of an electrically powered robotic subsea dredging crawler (EPRSDC). The modeling, simulation, and analysis were carried out using modelling software from Solidworks. The structural frame was assembled using the Tetrix max robotics kit. The kit’s structural components were produced from 1050 aircraft-grade aluminum. The results were used in optimizing and for considering other materials, and the to identify specific areas to be reinforced in future crawler designs.

Oct 3, 2023

By K. B. Le Bron, T. van Aard

The empirical pillar strength formulae have been widely, and in most cases successfully, applied to design underground pillars for mines in the Bushveld Igneous Complex (BIC). This paper presents the case for combining the empirical method with numerical modelling when it comes to crush pillar stability analyses. The benefits include an understanding of potential failure mechanisms, which may then be accounted for in the designs. In addition, the impact of weak layers, such as shear zones, the impact of the dip of the orebody, differences in layouts, such as holing widths and the presence of advanced strike gulleys (ASGs) immediately adjacent to the crush pillars, and stress regime (k-ratio) may be studied using numerical modelling, as it is not accounted for in the empirical method.

Mar 5, 2025

By W. A. Smith, M. C. Bekker, C. Marnewick

Projects or project-orientated approaches have become a common form of work in nearly all sectors of economies. This has led to concepts such as ‘projectified’ and ‘project orientated’ organizations. By defining projectification of a company, industry, or economy as the share of project work in total work, one can reasonably determine the impact that project management, and by default projectification, has had on that company, industry, or economy in terms of staff optimization and allocation. This paper presents the results for such a projectification study of the South African mining industry. This sector has long been a significant contributor to the country’s economy from a gross value added (GVA) and employment point of view. Understanding the impact of projectification and the project management way of work on this industry may potentially add significant value to both the mining and project management knowledge areas. We show that although the mining industry is considered by some to operate in archaic ways, the level of projectification has increased over time, and now represents approximately one third of all work conducted.

May 1, 2021

By X. M. Prévost

The reassessment of coal reserves has become a matter of urgency and has come as a result of the present situation of the industry, in the context of globalized coal economies, as well as new mining legislation and the advantages and difficulties of domestic coal suppliers. The de Jager report concerning coal reserves, released twenty years ago, can no longer be used as an estimate for accurately forecasting South Africa’s future coal production. The new reserve and resource study will promote the diversification of energy sources and provide a clearer view of the future of coal mining in the country. With plans to increase South Africa’s coal export capacity to approximately 84 million tons by 2005, it is uncertain whether the country really has sufficient reserves to meet this expansion, as well as satisfy the projected increase in inland demand. The face of South Africa’s coal industry and by association, the economy of our coal-dependent country, are both set to change. This is mainly due to factors such as the demise of most of the large collieries over the last approximately twenty years, growing numbers of economic empowerment producers, the emergence of strong competition in the export market, the dawn of Clean Coal Technologies (CCTs) and the Kyoto Protocol The paper will attempt to dispel some of the current myths about coalfields and reserves and highlight potential areas of high quality coal reserves, available mainly to new entrants in the industry. Keywords: Central Basin, Clean coal technologies, Coal combustion, Coal exports, Coalfields, coalLink, Coal reserves, Coal resources, Coal processing, Colliery, Economic empowerment, Discards, Fluidized bed combustion, Low-ash coal, Metallurgical coal, Power generation, Pulverized fuel, Reserve blocks, Richards Bay Coal Terminal, Run-of-mine production, Saleable production, SAMREC Code, South Dunes Coal Terminal, Steam coal, Synthetic fuels.

Jan 1, 2003

By S. Govender, J. J. L. du Plessis, R. C. W. Webber-Youngman

Spontaneous combustion (SC) is a cold oxidation reaction that generates heat, causing a temperature rise of the reactant and leading, with limited heat dissipation, to self-ignition of the reactant, which occurs without an external heat source. Although not limited to coal, the most significant hazard of SC are the fires that occur in coal mining operations around the world. These fires pose a serious risk to the safety of workers in the mines as well as adverse effects on the environment, and can affect the quality of life for current and future generations. We investigated the occurrence of SC in raw coal storage bunkers with the purpose of compiling a decision analyser for engineers designing or working with coal storage bunkers. Specific experts were interviewed from different backgrounds and companies, followed by field research at a coal mine. The important factors affecting the possibility of SC occurring were the type of coal supplied to the bunker, the mining practice, and physical conditions around the bunker. The information presented here will assist in reducing the SC risk in raw coal storage bunkers. These findings, together with the systematic decision analyser developed, will assist design engineers and mine personnel to take early preventative steps in managing SC. The decision analyser was tested for many different scenarios and gave good guidance on how to minimize and prevent SC in bunkers

May 1, 2021

By M. Z. Naghadehi, E. Emami, J. Sattarvand, R. Battulwar

In this paper, a methodology for a computerised recognition of joint sets on 3D point cloud models of rock masses is presented. The process starts with classifying joints on a 3D rock mass surface through training a deep network architecture and validated using manually labeled datasets. Then, individual joint surfaces are identified using the Density-Based Scan with Noise (DBSCAN) clustering algorithm. Subsequently, the orientations of the identified joint surfaces are computed by fitting least-square planes using the Random Sample Consensus (RANSAC). Finally, the joint planes are classified into different joint sets, and the dip direction and dip angle for each set are calculated. The performance of the proposed methodology has been evaluated using a case study. The results show that the presented procedure is fast, accurate, and robust.

Sep 1, 2021

By R. Altındag, D. Akbay

The point load index is a simple, fast, and inexpensive method for determining rock strength and can be applied both in the field and in the laboratory. There are, however, some disadvantages and limitations to the method, and the test results can be affected by the person carrying out the test, the rock characteristics, or the test device. In this study we describe an investigation into how the point load index value is affected by the shape of the conical platens used in the test. Point load index tests were carried out using different devices fitted with conical platens of different spherical radii, and on a modified device which circumvented the limitations/disadvantages. It was seen that the point load index value increased as the platen radius increased, as expected. In the case of testing using non-standard conical platens, an equation is proposed to normalize the point load index value with respect to the standard spherical radius value.

Nov 1, 2021

By S. Wakita, K. Aoki, Y. Mito, K. Date

It is of great importance to prevent a leakage of hazardous substances from underground storage plants, because this certainly leads to a fatal disaster for human societies. Therefore, effective grouting system needs to be developed, which can inject cement grout into low-permeable rock masses. Authors have carried out a series of laboratory injection tests using a fracture model and field tests in low-permeable rock masses. In these tests, not only was the superiority of dynamic grouting confirmed, but also the relationship between grouting-efficiency and injection parameters was investigated. In this paper, the results of laboratory injection tests and field tests together with theoretical approaches to them are mentioned. L’empêchement de la fuite des substances dangereuses des galeries de stockage est un traitement très important pour protéger la société humaine contre la comtamination catastrophique. Par conséquent, un procédé d’injection efficace doit être mis au point, qui peut injecter du coulis de ciment dans le rocher ayant une perméabilité basse. Les auteurs ont effectué une série d'essais d'injection en laboratoire en utilisant un modèle de rupture et d'essais sur le terrain dans le rocher ayant une perméabilité basse. Dans ces essais, était non seulement la supériorité du l’injection dynamique confirmée, mais aussi le rapport entre l’efficacité de l’injection et les paramètres d'injection a été étudié. Dans cet article, les résultats des essais d'injection en laboratoire et des essais sur le terrain ainsi que les méthodes théoriques pour les essais sont mentionnés. Es ist wichtig, Durchsickerns gefährlicher Substanzen aus unterirdischen Lagerstellen zu verhindern, weil dies für die menschliche Gesellschaft unter Umständen zu verheerenden Unfällen führen kann. Daher muß ein effizientes VerfugesSystem entwickelt werden, welches erlaubt den Mörtelschlamm in wenig durchlässige Felsenmassen einzuspritzen. Die Autoren haben eine Serie von Laboreinspritzungsversuchen mit einem Bruchmodell und Feldversuche an wenig durchlässigen Felsenmassen durchgeführt. Diese Versuche zeigten nicht nur die Überlegenheit des dynamischen Verfugens, sondern wurde dabei auch das Verhältnis zwischen Verfugen und Leistungsfähigkeit sowie den Einspritzungparametern untersucht. In dieser Studie werden die Ergebnisse der Laboreinspritzungtests und die Feldversuche zusammen mit den entsprechenden theoretischen Ansätzen erläutert.

Jan 1, 2003

1. Book reviews Dislocations and properties of real materials, edited by M.H. Loretto. London, The Institute of Metals, 1985. 392 pp. Reviewer: F.R.N. Nabarro Au &Ag heap and dump leaching practice, edited by J.B. Hiskey. AIME, 1984. 162 pp. $20 (member), $15 (student member), $30 (non-member) plus $3.50 for postage and handling. (Order from SME Books, Caller no. D, Littleton, CO 80127, U.S.A.). Reviewer: R.A. Snodgrass The cost and availability of Colombian coal, by Eric D. Jamieson, with the assistance of Kathleen Jamieson. London, lEA Coal Research (14/15 Lower Grosvenor Place, London SWl W OEX). £50 (in member countries), £100 (in non-member countries). Reviewer: W.C. Mather Extraction Metallurgy '85. London, The Institution of Mining and Metallurgy, 1985. £42. Reviewer: R.A. Snodgrass 2. Recent publications Mining annual review 1985. London, Mining Journal, Jun. 1985. 600 pp. £26.50 (surface), £39.50 (air). High heat production (HHP) granites, hydrothermal circulation and ore genesis. London, The Institution of Mining and Metallurgy, 1985. 593 pp. £27 (members), £30 (non-members). Potential mineral resources of Egypt. 144 pp. US$10. Available from Bendix Field Engineering Corporation-MPGAP, Box 1237, Grand Junction, CO 81502, U.S.A. 3. Mintek reports Report M212 South African costs of equipment for the metallurgical industry (1984). Report M213 The response of as-rolled 3CR12 steel to heat treatment. Report M214 A computer programme for use in the development of multi-element X-ray-fluorescence methods of analysis. Report M221 Commodity profiles for selected metals. Report MIO7D Upgrading of alaskite rock to feldspathic sand. (First issued Jun. 1983; reissued Nov. 1985). IMM awards Given below are details of the trust funds to which applications are invited for grants, etc., payable in 1986. Application forms, which must be returned to the Secretary before 17th March, 1986, are available on request. Applicants should note that, in general, preference will be given to members of the Institution.

Jan 1, 1986

By B. McFadzean, M. Tadie, T. Dzingai, M. Becker

Ores from a single deposit may exhibit extensive variability in their mineralogy and texture. The ability to quantify this variability and link it to mineral processing performance is one of the primary goals of process mineralogy. This study focuses on the effect of alteration in three platinum group element ore samples from the Great Dyke in Zimbabwe – two of which were more pristine compared to the third, which was locally classified as ‘oxidized’ ore. These ores are known to be characterized by varying degrees of alteration, resulting in numerous challenges in flotation and affecting both grade and recovery. Alteration, by near-surface oxidation, of the valuable base metal sulphides and platinum group minerals resulted in lower flotation recoveries of Cu, Ni, Pt, and Pd. Evidence of incipient oxidation was more readily observed in the base metal sulphide assemblage than the platinum group mineral assemblage, even though the loss in recovery (because of oxidation) was most significant for Pd. Alteration through hydration resulted in a significant increase in mass pull and dilution of concentrate grade through the inadvertent recovery of naturally floating gangue comprising composite orthopyroxene and talc particles. In this study, the amount of naturally floating gangue was more strongly correlated with the talc grain size distribution than the grade of talc in the flotation feed. The oxidation and hydration alteration reactions are not necessarily mutually exclusive, although one may be more dominant than the other, giving rise to ore variability.

Sep 1, 2021

By J. Hadjigeorgiou, T. R. Stacey

This paper introduces the Quantified Value-created Process (QVP), a decision-making process for use in mine design and operation. The implementation of the QVP is founded on a ten-step rock engineering design process and a ten-step strategic planning process. The potential of this approach is demonstrated by examples of value created as a result of good research, design, and planning. The QVP is divided into two parts, namely, a ‘planning the process’ section and an ‘implementing the process’ section, and can be considered to be an extension of the risk approach. All costs, direct and indirect, associated with a significant mining decision (design, operational, investment) must be quantified in advance of committing to that decision, to determine the value that will be created in the short, medium, and long terms. Ethical values, associated with health, safety, the environment, public perception, and social aspects, may be difficult to quantify in economic terms, but must nevertheless also be considered. In contrast with a traditional risk approach, the QVP will identify the upside, and allow executives to make more informed strategic decisions. In this context it is essential to actively engage upper management in the decision process.

Feb 2, 2022

By M. Buchmann, T. Mütze, F. Heinicke

Dry air classification is a well-known technique used for decades in the cement industry to separate material in the size range of 0.01-1.0 mm. Additionally, in corresponding dry grinding circuits with effective machines such as High Pressure Grinding Rolls (HPGR), the energy consumption can be reduced compared to wet applications. These dry systems are not state of the art in minerals processing plants, but first prototypes have been installed and an increasing number of projects are starting to evaluate this option. One challenge in this field is the mineral composition of ores, which have, by far, a higher variety in density and size than those of cement. High density particles such as iron- containing ones have higher settling rates than low density silica particles of the same size. The main question to answer in this paper is how to evaluate this effect, so a quantitative method using Mineral Liberation Analyses was developed to calculate two-dimensional partition curves. Additional statistical analyses allow for isolation and quantifying the interaction of density and size, enabling engineers to consider this effect for the sizing of process plants. The paper will present the method and selective results for a compounded ore of iron and silica. Keywords: HPGR, air classification, partition curve, MLA

Jan 1, 2020

By S. Lohmeier, D. Gallhofer, B. G. Lottermoser

In Southern Africa, historic mining and mineral processing of base metal deposits have almost exclusively focussed on the extraction of major metals, leading to the loss of remaining valuable raw materials into tailings dumps and waste rock piles. At the Namib Pb–Zn mine (Erongo Region, Namibia), historic base metal tailings deposits are present as unreclaimed exposed waste piles. The tailings comprise silt- (fraction A: d50 = 25 to 48 μm) to sand-sized (fraction B: d50 = 86 to 185 μm; fraction C: d50 = 210 to 230 μm) material and contain major concentrations of base metals (Pb av. 1.15 mass%, Zn av. 3.20 mass%), S (av. 9.95 mass%), as well as lower values of other metals (Cu av. 490 μg/g, Cd av. 133 μg/g, Ag av. 22 μg/g), and critical elements like Sb (av. 14.7 μg/g) and In (14.3 μg/g). Former mineral processing only targeted the extraction of galena and sphalerite. As a consequence, qualitative mineralogical composition of the tailings is similar to that of the primary ore. Ca–Fe–Mg(–Mn) carbonates, quartz, micas, chlorite, minor graphite, magnetite, and rare parisite relate to the former host rock and gangue matrix, whereas Fe-rich sphalerite, galena, magnetite, pyrite with minor pyrrhotite, rare arsenopyrite, marcasite, cassiterite, and accessory scheelite are original constituents of the primary ore. Reprocessing of such a material would be challenging, but a mixed Pb–Zn concentrate enriched in Cd and Ag might be obtained. In future, possible reprocessing of Namib tailings and associated disposal of wastes into an appropriately designed repository would not only generate valuable metal commodities, but such activities would also eliminate a major metal pollution source from the local environment.

Sep 9, 2024

By M. Steyn

The coordination compound tetrakis(1,3-diphenyl-1,3-propanediona to)zirconium(IV), [Zr(DBM)4], (DBM = dibenzoyl methane/1,3- diphenyl-1,3-propanedionol) was synthesized and characterized by single-crystal X-ray diffraction. [Zr(DBM)4] crystallizes in the monoclinic space group P21/c (a = 24.769(4) Å, b = 10.216(5) Å, c = 19.314(4) Å, and = 101.541(5)°). The coordination geometry around the zirconium atom, formed by the eight O-donating atoms of the four -diketonates, is found to be a near-perfect square antiprism. Crystal packing is stabilized by C?H... interactions throughout the crystal lattice. This structure is a noteworthy example of the application of ambient condition synthesis of zirconium compounds in N,N'-dimethylformamide (DMF) as reaction and crystallization solvent, highlighting the possibilities of aerobic condition metal purification through chelation.

Jan 1, 2014

By S. Bradshaw, A. Mabentsela

"Physical and numerical modelling methods were followed to identify mechanism(s) for tundish slag entrainment in a bare tundish and one with a flow control device (FCD).The physical and numerical models made use of water and paraffin to model steel and slag respectively. Observations from the physical model showed that the steel-slag interface remains immobile in both cases. Entrained paraffin formed droplets approximately 1 mm in diameter. Results from both models (numerical and physical) showed that in both cases (bare and FCD case), areas of high entrained slag concentration exist near the inlet region. The entrained slag concentration decreases towards the tundish endwalls.Flow patterns and velocities tangential to the steel-slag interface from the numerical model showed that slag entrainment in both the bare tundish and tundish with a FCD possibly takes place via two mechanisms. First, the slag moves across the steel-slag interface via mass transfer; secondly small velocities tangential to the interface at depths greater than 10 mm below the interface carry the already ‘entrained’ slag into the bulk steel phase. These tangential flow patterns are dominant in the inlet region, hence the high concentration of entrained slag in this region. IntroductionThe tundish serves as the last metallurgical vessel through which steel passes before solidifying in the moulds. It is in the tundish that the last traces of non-metallic inclusions should be removed, otherwise the inclusions carry over to the moulds and cause defects in the steel product. In the tundish, the slag is less dense than the melt and thus resides on the top of the melt. The slag provides a sink into which the non-metallic inclusions float to and dissolve. The slag also protects the melt from air and heat loss. However, when slag is entrained in the melt as a result of increased turbulence or shearing at the steel-slag interface, slag can become a source of nonmetallic inclusions.Numerous studies on flow patterns in the tundish have been carried out since the introduction of the tundish. These studies were aimed at improving the flow characteristics in the tundish (Chattopadhyay, Isac, and Guthri, 2010; Cloete, 2014; Jha, Dash, and Kumar, 2001; Jha, Rao, and Dewan, 2008;"

Jan 1, 2017