Search Documents

By Edward L. McHugh, Charles Sabine, Louis J. Denes, Jami M. Girard, Peter Metes

The Spokane Research Laboratory, National Institute for Occupational Safety and Health, is investigating various remote sensing technologies as possible tools to detect, monitor, and mitigate hazardous situations in surface mines that could lead to catastrophic slope failure. Promising technologies include a field-portable spectro-polarimetric imager and a stationary interferometric radar device. Field tests were conducted of a prototype visible and near-infrared spectro-polarimetric imager (SPI) built at the Carnegie Mellon Research Institute. The SPI employs anacousto-optical tunable filter (AOTF) to control wavelength, a phase retarder to measure polarization signatures, and a digital camera and computer to capture data. Images obtained at the Mountain Pass and Castle Mountain mines in southeastern California showed that the instrument is capable of obtaining hyperspectral images of highwalls, outcrops, hand samples and drill core in the field. We have retrieved spectra from Mountain Pass images that closely match those of bastnaesite and have had some success in classifying images. Although radio frequency noise in the data limited spectral classification of imagery, we project that careful alignment of the AOTF should minimize the noise and greatly improve classification.

By Parviz F. Rad

The increased use of tunnel boring machines (TBM) has stimulated laboratory research to optimize the cutting parameters of these machines with the objective of increasing machine efficiency and penetration rate. Laboratory-scale rock cutting experiments have succeeded in identifying many of the important parameters involved in rock-cutter interaction. Although scaling factors may be required to apply the results directly, the concepts developed can be used qualitatively as design guidelines for boring machines. The Bureau of Mines Twin Cities Mining Research Center has recently developed a large-scale rock cutting device (RCD) that will simulate many of the operating parameters of the tunnel boring machines in the laboratory under a controlled environment. The results of the experiments with this device will be directly applicable to the design of TBM's.

Jan 1, 1973

By D. Debasis, Christopher Mark, Gregory M. Molinda

The stability of any underground opening is, in large part, a function of the strength of the rock mass which surrounds it. The Coal Mine Roof Rating (CMRR) has been developed to quantify the defects in the rock mass and compile a strength value which can be used for engineering design. The CMRR has been applied to a number of ground stability problems, including chain pillar design, roof bolt selection, hazard assessment, intersection design, and numerical modeling. The CMRR procedure and some of these applications are described in this paper. The CMRR will soon be available in a Visual Basic computer program, allowing easy integration into exploration programs and standard roof fall assessments.

By N. F. LeJeune, Earl C. Lane

This is the third of a series of reports on a survey of petroleum prod- ucts manufactured on the Pacific Coast from California crude oils. California crudes differ in many characteristics from the petroleum produced in the other parts of the United States, and the claim has been made that some of the present Federal Specifications for petroleum products tend to discriminate against Cali- fomia products. The purposes of the present survey are to determine what par- ticular specification requirements Califomia petroleum products characteristical ly fail to meet, how widely the products deviate from these requirements, and if possible to show whether the fault lies with the specifications or the products, or along what lines investigation to determine this question should proceed. The first report of the series gave the physical and chemical properties of the samples of gasoline and mineral spirits. A second report**, gave the physical and chemical properties of samples of lubricating oils. The present report deals entirely with burning and fuel oils. The refin ing companies have continued their very cordial and helpful cooperation. Seven samples of kerosene, four samples of Diesel fuel and eight samples of fuel oil were obtained. The methods of analysis used are those adopted by the Interdepartmental Petroleum Specifications Committee, published by the Bureau of Mines in Technical Paper No. 323. The specifications used for corparison are those officially adopted by the Federal Specifications Board for the use of the various Depart- ments and Independent Establishments of the Government, effective February 3, 1923, and published by the Bureau of Mines in Technical Paper No. 323, Part 1. Specific gravity, degrees A.P.I., viscosity and other special tests al- though not required by the specifications have been given for comparison. All temperatures are recorded in degrees Fahrenheit. Tables have been prepared giving data on physical and chemical propertios of the individual samples. Before each table the classification and specifica- tions for the particular class of oil considered in the table are given. Follow- ing each table, brief notes show wherein samples deviate from specification re- quirements.

Aug 1, 1923

By D. E. Hirsch

The Bureau of Mines, as a part of American Petroleum Institute Research Project 60, Characterization of the Heavy Ends of Petroleum, has made extensive use of gel permeation chromatography (GPC). Data developed in this study were used to develop several correlations that greatly expanded the usefulness of GPC and the data have been used as an aid in the interpretation of mass spectra (MS). GPC retention volume data on pure compounds were used with molecular structure to develop correlations that can be used to accurately predict retention volumes, molecular volumes, densities, chain lengths, and ring numbers of many components of petroleum without resorting to further laboratory experimentation. Conversely, the correlation can be used to select or reject some compounds from several possible compounds that are indicated on the basis of MS analysis. The utility of these correlations in compound type characterization is demonstrated by showing their application to 330° to 550° C fractions from a low-sulfur and a high-sulfur crude oil.

Jan 1, 1974

By J. E. Murphy

The high-purity thorium metal was prepared by the Bureau of Mines from electrolytically produced thorium alloys. The thorium-chromium and thorium-manganese alloys were separated into the component elements by vacuum distillation. Chromium and manganese impurities remaining in the thorium metal after distillation at 1,850° C were <0.005 weight-percent. Removal of volatile impurities such as aluminum, calcium, magnesium, and lead was also accomplished.

Jan 1, 1969

By Thomas Varley

Data on the consumption of reagents used in flotation during the years 1923 and 1924, in metallurgical plants in the Unites States, are presented in this paper. Two previous reports Lave been issued by the Bureau of Mines on consumption of oils and other reagents used to flotation - namely, "Statement of Flotation Oils," by O. C. Ralston, issued in 1913, and Serial No. 2203, "Consumption of Reagents Used in Flotation," by Thomas Varley, for the year 1919, issued in January, 1921.

Jan 1, 1925

By M. L. Whisman

Radiotracer techniques were developed for stoichiometric studies of photochemical reactions associated with atmospheric smog formation. Stock blends of separate hydrocarbon and oxygenated compounds were prepared and calibrated. 14C-labeled reactants and products in reaction systems involving hydrocarbons and nitrogen oxides at the ppm level were analyzed for qualitative and quantitative data. Precision and accuracy of these methods developed by the Bureau were determined by replication and statistical treatment of data, and these methods are described.

Jan 1, 1969

To precondition a stope in advance of mining and thus reduce or prevent rock bursts. Approach Drill deep holes from a mine opening in a radial pattern in the vein and load and blast to fracture, the rock prior to production mining How It Works Preconditioning of a sphalerite galena vein in a hard gangue of quartz and quartzite creates a zone of softer rock that fails by displacement rather than violently as an elastic-battle mass. However, the entire area must he analyzed carefully so that the stress transfer does not cause problems in other workings of the mine A typical drill hole pattern and explosive loading is shown in the sketch. Hole diameter is about 4 inches and a down-the-hole, type drill is used. Drilling speed in hard quartzite is about 12 inches per minute High pressure compressed air (250 psi) is used to run the drill. An overhand cut-and-fill stoping area on the 7700 level of Hecla Mining Company&apos;s Star Mine in Burke, Idaho was preconditioned above and below the

Jan 1, 1981

By John Ward Smith

An analytical method developed by the Bureau of Mines to determine dawsonite, nahcolite, and nondawsonite alumina (called excess alumina) extractable from Green River Formation oil shales is presented. The method requires water extraction of nahcolite followed by HCI-extraction of dawsonite and an unidentified mineral yielding excess alumina from the water-leached residue. Instrumental determination of sodium in the water extract and sodium and aluminum in the HCI extract measures the sample&apos;s content of the minerals. Detailed evaluation shows the method to be adequately specific, precise, and reproducible and free from uncorrectable interferences. The method&apos;s results define precisely the production of sodium carbonates and alumina possible from a sample of oil shale and the interval it represents. Shale-oil yields, nahcolite contents, and yields of extractable alumina determined on 83 samples representing an 821-foot section of dawsonite-nahcolite-bearing shale from .Colorado Corehole No.3, drilled in the north part of Colorado&apos;s Piceance Creek Basin, are presented. These samples resulted in nahcolite contents to 53.3 percent, oil yields to 48.3 gallons per ton, and alumina yields to 5.80 percent. Use of these data to evaluate the production potential of a section of the formation are suggested.

Jan 1, 1969

By J. W. Town

The Bureau of Mines studied the effects of reducing gas composition, tem-perature, and superficial gas velocity on the regeneration rate of alkalized alumina. Regeneration was assumed to follow the simple first order reaction for removal of sorbed S02: dµ/dt = -Kµ. An Arrhenius relationship can be plotted, which shows an activation energy of about 75 kcal/mole for simulated reformed propane. The general effects of the individual gases can be described as follows: (1) CO and H2 produced rates proportional to their con-centrations, up to about 5 percent for each; (2) addition of CO2 had no effects on the regeneration rate by CO; (3) the regeneration rate by H2 was lowered by the addition of H2O while the regeneration rate by CO was increased by 0 addition; (4) H2S showed a positive effect up to concentration levels of about 2 percent and then produced a rapid negative effect; (5) carbonyl sulfate (COS) increased the sulfur content; and (6) propane was as effective in regenerating the loaded pellets as was simulated reformed propane.

Jan 1, 1971

By J. J. Henn

A process is evaluated for recovering metallurgical-grade manganese are from the low-grade manganiferous iron ores of the Cuyuna Range, Minnesota. The process, developed by the Bureau of Mines, employs high-temperature sulfatization of the are to form manganese sulfate and reduction of the are to convert the iron to a magnetic oxide. The roasted ore is water-leached to dissolve the manganese sulfate, which is then separated from the leach residue, is crystallized, and is calcined to produce the manganese product. Iron is recovered from the leach residue by magnetic separation, and is pelletized and calcined to produce byproduct iron ore pellets. The fixed capital cost for a plant yielding a product containing 100 tons of manganese per day is $19.6 million on a mid-1970 basis when the raw are contains 4.84 percent manganese. The estimated operating cost of the plant is $211 per ton of contained manganese. Graphs are included to show the effects of ore cost and varying manganese content of the raw ore on the estimated operating cost.

Jan 1, 1972

By Ronald D. Hill, Elmore C. Grim

To better appreciate the problems associated with surface mining, it 1s imperative that the stripping operation be understood. Surface mining is a very broad term and refers to any process of removing the earth, rock, and other strata in order to uncover the underlying mineral or fuel deposit. Strip mining is a type of surface mining in which the overburden is removed in narrow bands, one cut at a time. Strip mining methods employed to recover coal can be divided into two general types: area and contour.

Jan 1, 1974

By B. J. Scheiner

The Bureau of Mines investigated an electrolytic technique for oxidizing ore slurried with brine to determine its effectiveness in extracting mercury from ores. Optimization experiments conducted on a 2.5-pound-mercury-per-ton ore resulted in 95 percent mercury extraction with operating conditions of 30° C, a current density of 0.5 ampere per square inch, and a treatment time of 3.5 hours. Corresponding power consumption amounted to 38 kilowatt-hours per ton of ore treated. Amenability experiments conducted on 62 different mercury ores resulted in 90 to 99 percent mercury dissolution from ores containing 0.6 to 20 pounds of mercury per ton of ore, Treatment time ranged from 1 to 7 hours in 4-to 20-percent sodium chloride solutions, and power consumption was in the range of 10 to 50 kilowatt-hours per ton of ore. Pilot mill experiments in a 100-to 200-pound-per-hour extraction plant have been in progress to quantify power and reagent requirements. These data will be reported in a subsequent publication.

Jan 1, 1973

By W. H. Ode

Low-temperature distillation tests at 200°, 350°, and 500° C. were made on a subbituminous coal from Boulder County, Colo., and a subbituminous coal from Weld County, Colo., in connection with a survey of carbonizing properties of American coals and investigations of their chemical and physical properties. The coal represented by the sample from Weld County was reported to give off combustible volatile matter at unusually low temperatures When placed on a fuel bed. The yields of tar and oil and the composition of the gas from this coal, as obtained in the distillation tests, did not confirm this report. These yields and the gas composition of the Weld. County coal differed but little from those obtained from the coal from Boulder County. Both coals yielded tar and gas in amounts considered to be normal for coals of their rank.

Jan 1, 1937

Reduce respirable dust in coal preparation plants. Approach Survey a representative sample of coal preparation plants to (1) determine the dust problem extent, and (2) evaluate practical dust control techniques. Coal Preparation Plant Survey Results Of the approximately 500 coal preparation plants in the United States, 18 plants in six States were randomly selected for survey. The raw hourly capacities ranged from 250 to 1,250 tons, plant construction dates ranged from 1037 to 1982, and usually 3 to 10 workers were required per shift. Respirable dust concentrations within the plants surveyed ranged from very good (less than 1 mg/m&apos;) to very poor (14 mg/m3). No relationship was found between dust concentration and age or capacity of the plant. Six of the plants had long-term respirable dust concentrations between 7 and 14 mg/m&apos; in specific areas; six had concentrations between 2.2 and 6.2 mg/m&apos;. Except fur ventilation, only 4 of the 18 plants used operating dust control devices with mixed effectiveness.

Jan 1, 1989

By Michael T. Nigbor

The Bureau of Mines assisted the Rocky Mountain Energy Co. in a pilot-scale in situ leaching experiment at Casper, Wyo., to determine if sulfuric acid can be used as a cost-effective alternative lixiviant (leachant) for uranium in situ leaching. This experiment, which lasted more than 2 years, is the first fully documented pilot-scale operation in which the leaching-restoration cycle was completed using sulfuric acid instead of the more common carbonate-bicarbonate leachant This report describes activities at the experimental site, presents extensive geochemical data from startup to site restoration, compares laboratory and field experiments, and discusses the environmental aspects of acid leaching. The data showed that sulfuric acid is apparently an effective leaching solution. Three to five grams of acid per liter of ground water resulted in a production solution grade of 80 to 100 ppm uranium. Restoration was successful, but required extended flushing. The pH was the last chemical parameterto return to baseline, requiring about 350 days. This was longer than was predicted in laboratory simulations. The data also showed that mobilization of toxic elements such as selenium, arsenic, radium, thorium, and molybdenum stayed within reasonable limits and quickly fell back to preleach concentrations during restoration.

Jan 1, 1982

By Steven R. Davis

Dear Interested Party: Subject: Notice of Intent to Solicit Outside Opinions Regarding Amendments to the Rules Concerning the Leasing of State Owned Lands for the Mining of Metallic Minerals The Department of Natural Resources, Division of Minerals, is seeking outside opinions concerning the leasing of state owned lands far the mining of metallic minerals. Enclosed for your information in a copy of the Notice of Intent to Solicit Outside Opinions Regarding Amendments to the Rules Concerning the Leasing of State Owned Lands for the Mining of Metallic Minerals.

Jan 1, 1994

By R. V. Ramani

"Exposure to respirable contaminants in mine atmospheres has long posed a serious hazard to miners. The control of these hazards, some of which can have sudden and catastrophic effects and some others, slow and long enduring consequences, has been a major concern for labor, management and government alike. This concern has manifested itself in four primary mechanisms of control -- (1) regulatory control through minimum standard setting by the passage of mine health and safety laws, (2) engineering control through design and operation of 'mines according to the best recommended practices, (3) medical control through periodic physical examinations, wearing personal protection devices, etc., and (4) legal and social control through workmen's compensation laws for occupation related health deterioration:-The respirable contaminants in mine atmo¬spheres are toxic and explosive gases, toxic and explosive dusts, diesel exhaust particu¬lates, radon progeny, etc. Perhaps the most important of all these and the most widely occurring in mine atmospheres is respirable dust, an inevitable product of fragmentation, a unit operation fundamental to all mining operations. In fact; the-most serious health hazard for workers in the mining and minerals processing industries is still the exposure to respirable dust, and solutions to the problem of respirable dust disease remain to be found.The 1969 Coal Mine Health and Safety Act and its provisions for the respirable dust standards in underground coal mines are briefly reviewed. An overview of the research accomplishments in meeting the standards is presented. The current state of knowledge on the effectiveness of the standards and the new and emerging problems are discussed. A brief summary of the research programs of the Generic Technology Center on Respirable Dust is presented.In general, underground mines are becoming increasingly safe. The mine atmospheric environment is definitely improving * Professor and Head, Department of Mineral Engineering,-The Pennsylvania State University, University Park, PA for the better. Significant progress has been made in lowering the dust levels in mines. It is generally agreed that mines are less dusty today than they were a decade ago. However, as long as the risks of occupation-related diseases are not completely eliminated, vigilance can hardly be relaxed, and the search for engineering solutions must be intensified."

Jan 1, 1988

By H. V. Makar

An aluminizing dross which is accumulating as a waste material in substantial quantities was tested for possible use as a steel deoxidizer. This material, consisting mainly of aluminum, silicon, and iron, was used to deoxidize laboratory-scale melts ranging from 7 to 100 pounds. Oxygen analysis showed that the aluminizing dross was effective in reducing oxygen levels in steel. A direct comparison with aluminum wire showed the dross material to be at least as effective. Under similar test conditions with 7-pound melts, 3 grams of aluminum reduced the oxygen concentration from 210 to 175 ppm, while 4 grams of aluminizing dross (equivalent to approximately 2 grams aluminum) reduced the oxygen concentration from 250 to 170 ppm. An additional 4 grams of aluminizing dross produced a final oxygen concentration of 140 ppm.

Jan 1, 1972