Search Documents

By E. R. Cole

Bench-scale research at the Bureau of Mines has resulted in the successful development of a combination electrorefining-electrowinning method for recycling all the lead in scrap batteries. The method reduces energy consumption and eliminates toxic emissions, in contrast to present pyrometallurgical smelting, and the lead produced is pure enough for use in maintenance-free batteries. Anodes cast from molten lead scrap were electrorefined in 1-and 2-liter plastic cells using an electrolyte composition of 70 g/l Pb and 90 g/l free H2SiF6 (fluosilicic acid). Both reagent-grade and waste H2SiF6 were used. Cathode starting sheets were made from refined lead. Aloes, and later bone gelatin, and calcium lignin sulfonate addition agents were employed. The sludge remaining after separation of the lead metal was treated in a two-step leaching operation to solubilize the lead for recovery by electrowinning. Conditions for electrowinning were essentially the same as for electro-refining, except that insoluble Pb02-Ti (lead dioxide-coated titanium) anodes were used. The best results for both electrorefining and electrowinning were obtained with a current density of 170 amp/m2 and a cell temperature of 25° to 35° C. Cathode purity ranged from about 99.9 to 99.99+ pct Pb. Maximum energy consumption after 3 days, for electrorefining and electrowinning, was 90 and 700 kwhr per metric ton of refined lead, respectively.

Jan 1, 1981

By M. R. Geer

The ever-increasing need to guard against stream pollution has intensified interest in the problems of handling and disposing of flotation tailing. Therefore, the Bureau of Mines investigated the possibility of using crushed washery refuse to adsorb the free water in thickened flotation tailings on a bench scale and then in a pilot plant because the conventional methods of disposing of coal flotation tailings--impounding them or filtering them so they are dry enough to be conveyed to the refuse dump--are sometimes either impractical because of space limitations or costly because of low filter capacity. Most of the refuse samples tested were of similar mineralogical composition and exhibited similar water retention capability. The amount of crushed refuse required to adsorb the water in a particular tailing was influenced greatly by the fineness of the solids in the tailing and hence the percentage of solids to which it could be thickened. The ratio of crushed refuse to tailing solids required to provide a mixture dry enough to be carried on an inclined conveyor belt varied from 2.4 to 6.4. Several chemical agents that were tested were very effective in turning the free water in tailings into a stable gel. Fly ash also was very effective in adsorbing water.

Jan 1, 1968

By W. E. Young

This paper describes operations of the Chief Consolidated Mining Co. at the Chief mine in the Tintic district, Juab County, Utah, where the outstanding problem is water control; the unique pumping methods employed are featured in this report. The ore bodies in this district occur as long, narrow shoots along fault fissures, usually in the Bluebell dolomite of Ordovician age. Oxide ores predominate above the 1800 level, which is also the natural water level. Sulfide ores containing lead, zinc, silver, and gold extend below the 1800 level. The mine is developed by vertical shafts and winzes, from which drifts are driven to the ore bodies. In the lower levels of the mine these drifts extend long distances from the shafts or winzes because of the relatively low dip of the ore shoots. The mine has been worked to the 2800 level and the 18-411 winze extends to the 3080 level.

Jan 1, 1958

By W. W. Agey

The Calico silver-barite deposits near Barstow, Calif., are a potentially important resource. Exploration performed by two major mining companies out-lined large tonnages of ore that assayed at 2 to 3 ounces of silver per ton and 7 to 15 percent barite. Laboratory beneficiation work was done by the Bureau of Mines on four samples to develop methods for recovering the silver and/or barite. Cyanidation recovered from 47 to 60 percent of the silver from ore ground to approximately 100 percent minus 325 mesh. Salt roasting minus 10-mesh material, followed by regrinding and cyanidation, recovered 75 to 85 percent of the silver. From 75 to 90 percent of the barite was recovered in a plus 92-percent barite product from either the natural ore or from cyanidation residues. Salt roasting before cyanidation precluded recovery of the high-grade barite concentrate from the leach tails.

Jan 1, 1973

1. In 2002, a total of 2,820 contracting companies reported employment at coal mines to MSHA.

Jan 1, 2004

By A. J. Strazisar

The Bureau of Mines conducted a laboratory investigation to study the effectiveness of low-pressure steam and water spray in suppressing respirable dust at the tips of a saw-type cutting wheel. Suppression efficiencies were found to be proportional to the amount of the water or steam applied at the cutter tips. For equivalent water output rates, a maximum efficiency of approximately 80 percent was reached for both steam and water spray. Results from the steam and water spray tests showed an increase in suppression efficiency with an increase in particle size of 1 to 8 micrometers. The data indicate no advantages for using steam as a dust suppressant.

Jan 1, 1972

By Robert J. Timko

The objective of this Bureau of Mines research work was (1) to determine how well the E. I. Du Pont de Nemours and Company P-2500 personal dust sampling pump controls the flow rate at 2 L/min and (2) to compare respirable dust mea-surements made using the P-2500 with those made using a nonpulsating sampling flow system, both using the Dorr-Oliver 10-mm nylon cyclone dust size classifier. The calibrator and the operation manual for the P-2500, supplied by the manufacturer, were also evaluated. Flow tests consisted of long-term (6-to 8-hour) flow stability tests at various backpressures, a low-flow indicator examination, flow controller response time tests and pulsation tests. Dust tests were performed using coal, silica, and Arizona road dust. No tests were performed to examine effects of temperature, barometric pressure, vibration, or mechanical shock. These pumps performed well within manufacturer specifications in all tests.

Jan 1, 1982

By Steven J. Page, William A. Heitbrink, Andrew B. Cecala, Edward D. Thimons, John A. Organiscak

Miners at noncoal surface mining operations are often exposed to high levels of respirable dust. In an effort to lower the respirable dust exposure of these surface miners, the National Institute for Occupational Safety and Health (NIOSH) has been conducting research to address this problem in a practical and economically viable manner. One successful effort deals with lowering the dust exposure of equipment operators in enclosed cabs. Many types of surface mining equipment utilize enclosed cabs to protect equipment operators from dust exposure. Normally when the equipment is new, the cabs are fairly airtight. These tightly sealed cabs, combined with good filtration systems, generally provide the operator with good dust protection. However, most mining equipment is older, and as aging occurs, many components of the enclosure deteriorate. The structural integrity of the cab diminishes and the effectiveness of the air filtration system fails. NIOSH has been successfully researching costs-effective methods to improve both filtration effectiveness and cab integrity of these older cabs in order to provide a healthier work environment for equipment operators. Dust sampling records indicate that drill operators and helpers have the highest dust exposure of all workers at surface mining operations. Since much of the overburden contains a high percentage of silica, the health hazard associated with this dust can be even more serious. NIOSH research is addressing techniques to lower respirable dust levels at surface drilling operations. INTRODUCTION NIOSH's mission is to assure a safe and healthy work environment for the working men and women of this nation. The primary emphasis of NIOSH's Pittsburgh Research Laboratory (PRL) is mining health and safety research. This report focuses on two areas of research

By David F. Smith, F. A. Hartgen

"Incidental to a cooperative investigation with the Carnegie Institute of Technology and the International Combustion Engineering Corporation on the burning characteristics of a powdered coal and the powdered semi-coke therefrom, the U. S. Bureau of :alas has determined the relative temperatures at which rapid self-heating occurs in these two fuels. Determinations were made on various screen sizes of the two fuels. Chemical analyses on different sizes were made in the bureau's Coal Analysis Laboratory, of which H. M. Cooper is in charge. The true densities were determined b the method given in Bureau of Mines Technical Paper 8.4The apparatus used in the determination of the temperatures for rapid self-heating was similar to that used by Wheeler A 10-gram sample of the fuel was placed upon a screen in a glass tube enclosed in a vertical electric furnace. The tube was surrounded with sand. One thermocouple -as imbedded in the sand and another in the fuel. Measurements of the temperatures were obtained at regular intervals with a recording potentiometer, as the furnace temperature was uniformly raised. Dry air was passed down through the fuel samples at a uniform rate of 123 c. c. per minute; the temperature of the air was substantially that of the furnace."

Oct 1, 1929

By Leonard J. Prosser, Joseph Cervik, John H. Perry

The Bureau of Mines has developed several techniques for draining methane from coalbeds in advance of mining. Drilling long horizontal holes from an underground location is one such technique, which was successfully demonstrated in the Pittsburgh and Sunnyside Coalbeds. The same technique has now been applied in the Mary Lee Coalbed at Jim Walter Resources, Inc. 's No. 4 Mine, Brookwood, Ala. , where two holes were drilled horizontally--one to a depth of 1,010 feet (308 m) and the other to 540 feet (165 m). The 1,010-foot (3083) hole proved successful in degasifying a portion of the Mary Lee Coalbed. The hole drained methane for 1 year, during which time the initial gas flow of 200,000 ft3/d (5,663 m3/d) declined to 65,000 ft3/d (1,840 m3/d). Total gas production was 40 x lo6 ft3 (1.1 x lo6 m3 ). The gas was of commercial quality, with 98 pct methane and a heat rating of 990 Btu/ft (36.89 Mj/m3). The methane emissions from the faces of the mine section advancing into the degasified zone were reduced by 60 pct. The 540-foot (165-m) hole was terminated prematurely when it became impossible to maintain an open hole. Because of caving, very little gas was drained through this hole.

Jan 1, 1982

By H. L. Riley, B. W. Gandrud

"INTRODUCTION AND SUMMARYIn connection with a program of research work on coal at its Southern Experiment Station, the Bureau of Mines, in cooperation with the University of Alabama, conducts washability studies of samples of coal from coal fields in Alabama and other Southern States in which commercially important deposits of coal occur. The first such study on coal from a bed in the Arkansas field has been completed, and the results are presented in this report.One of the main objectives of a washability study is to obtain technically and commercially important data in connection with the best methods for preparing and utilizing the Nation's limited reserves of good coking coal. Such information is important from the standpoint of conservation in that it facilitates selection of preparation methods that will yield a good grade of coking coal with a minimum of losses of coal in the rejects.The coal on which this report is based was obtained by underground and tipple sampling at the quality mine of the Quality Excelsior Coal Co. about 3 miles east of Hackett, Ark. This mine operates in the Upper Hartshorne bed, which, as the main source of coal in what is known as the Hackett-Excelsior district, yields an excellent grade of low-volatile coking coal, which is marketed at steel plants in Colorado and California. Production from this bed by the major producers in the Hackett Excelsior district was at the rate of about 125,760 tons annually in 1949, according to the Keystone Coal Buyers Manual. 2/In the laboratory, the tipple sample was crushed to 6-inch top size and screened on a 2-inch round-hole screen. The 2-inch to 0 undersize, amounting to 71.4 percent of the total sample, was fractionated into a series of screen sizes and float-and-sink products to get data for determining the washability characteristics of the coal. Before the screening and float-and-sink tests were made, however, machine cuttings, which are now gobbed underground, were added to the 2-inch to 0 sample. Enough of these cuttings were added so that the resulting mixture was considered representative of what the 2-inch to 0 run-of-mine coal would be if all machine cuttings, including the part now being gobbed, were brought to the tipple as a part of the run-of-mine coal.The mixture obtained referred to in this report as the run-of-mine or raw coal."

Mar 1, 1953

By Donna L. Anderson

This U.S. Bureau of Mines report discusses the status of a laser-based guidance system to provide position and heading feedback and closed-loop control of tramming maneuvers for a continuous mining machine. The system has been developed and tested at the Bureau, and is now being prepared for underground experiments. The system hardware includes laser scanners, a sensor communication network, and host computer hardware. The system software includes a position and heading computation module and a tram control module. The description of the software includes discussions of laser data acquisition, error compensation methods, position and heading determination, safety checking for continuous miner tramming, and closed-loop tram control. The accuracy of the laser scanner's data, the reliability of the lasers in a dusty environment, and the system's accuracy on tracking the position and heading of the continuous mining machine are shown in the results of experiments performed at the Bureau. Conclusions are stated based on these experimental results, and further work to improve the system performance and prepare for underground testing is discussed.

Jan 1, 1990

By R. V. Ramani, A. S. C. Owili-eger

List of Numbers

Jan 1, 1974

By Jr. Oitto

A polyester-type resin and deformed-steel reinforcing bars (rebars) were used in to strengthen and to stabilize bolted, fractured wall rock along pas 1:'y. in a western gold mine. Reinforcing bars were placed in boreholes drilled into fractured rock and then were surrounded by resin pumped under pressure into the holes and intersecting fractures until the wall rock was thoroughly impregnated. Pumping and injection equipment and infusion procedures are described. Visual examinations for movement in bonded and adjacent unbonded rock were made for 3 years. Fractured walls containing resin-rebar installations were strengthened. The results suggest that resin-rebar support can be used advantageously and economically in repairing fractured or broken rock when compared with rock bolting or timbering.

Jan 1, 1965

By J. E. Miller

This paper reports experimental determinations by the Bureau of Mines of compressibility factors to 4,000 pounds per square inch absolute (p.s.i.a.) for helium at temperatures from -10° to 130° F. and for 16 helium-nitrogen mixtures at 70° F. This information is needed for computing accurate discharge volumes and is necessary for determining an average-density value for use in orifice-meter formulas. In thermodynamic calculations, several functions of the compressibility factor with pressure and temperature are required. The data in the original publications (6, 8)5 of this study have been reexamined and have been given a more comprehensive treatment. The recalculated compressibility factors are higher by approximately 0.2 percent because in the earlier work a linear relationship between the compressibility factor of helium and pressure was assumed.

Jan 1, 1961

By Robert P. Vinson

The Bureau of Mines investigated the presence and extent of methane accumulations in mine roof cavities using a full-scale mine model. Methane was released at a constant rate into the roof of a cavity built onto a 700-ft wind tunnel. Two box-shaped roof cavities were used in the study: one had a volume of 114.7 cu ft; and the other had a volume of 57.3 cu ft. Methane concentration was measured at 28 sampling points in the cavities using 21 different combinations of gas emission rates and air velocities. Brattice hung in the cavity helped reduce methane concentrations without auxiliary ventilation. It was also found that the effective ventilation rate increased by a factor of 40 in the large cavity and by a factor of 20 in the small cavity when air velocity was increased from 100 to 600 fpm.

Jan 1, 1978

Until man was able to produce light, his working day was pretty much limited to daylight hours. Underground miners have a special problem because in a mine it is just as dark during daytime as it is at night. The first devices used for mine lighting were torches and open flame 011 lamps. Torches made from twisted grass and dipped in tallow or pine pitch would burn for a while, but they made a lot of smoke and probably went out when they were needed most. During the 15001s, miners lamps consisted of a small metal dish with a hook attached to hang it up. The saucer-shaped dish was filled with animal or fish oil and a wick made of twisted fibers was laid In the 011 and hung over one edge where it would burn. This lamp would burn longer than a torch, but the amount of light cast by the pale, flickering flame was probably only a little better than no light at all.

Jan 1, 1976

By J. M. Mutamansky

"Coal mine dust research throughout the world has been stimulated by the recognition of its importance in the development of coal miners' diseases, particularly coal workers' pneumoconiosis (CWP). A historical look at the problem and the present state of knowledge in this area of importance to the worldwide coal industry is presented. A summary of progress made in this area is provided and some research ideas for the future are discussed.1. INTRODUCTIONI thank Dr. Yong Won John, President of the Korean Institute of Mineral and Mining Engineers, for his invitation to address the International Symposium on Coal Mining and Safety. This presents me with an interesting opportunity to take a broad look at the research in coal mine dust and where we are going. From this broad perspective, we can all view the progress and problems that are apparent in the present state of knowledge of coal mine dust. One important element in the review of coal mine dust research and its role in miners' diseases is that of its history. The existence of diseases attributed to the mine atmosphere is often traced back to Pliny the younger in the first century A.D. His work on natural history mentioned observed human effects attributed to mine fumes and vapors. However, the subject of the effects of dust in the mine was not mentioned in published literature until 1556 when Agricola discussed the ailments of miners in his day (Seaton 1975).For many centuries, many medical ailments of the lungs were often categorized together and distinct diseases were often not recognized until more modern times. The ability to distinguish different lung diseases was limited until the discovery of X-rays in 1986. Nonetheless, Zenker in 1866 applied the term pneumonokoniosis to any disease where dust gathers in the lymphatic depots of the lungs. This term was changed to pneumoconiosis in 1932. While pneumoconiosis was defined in the 1800s, scant attention was paid to control of miners' diseases until recent decades. The first attempt to control disease through control of the mine atmosphere has been attributed to the South Africans who instituted a silica control in 1910 (Drinker and Hatch 1954)."

Jan 1, 1989

By U. E. Brown

This papery describing the mining methods employed by the Bunker Hill and Sullivan Mining and Concentrating Co. at Kellogg, Idaho, is one of a series being prepared by the United States Bureau of Mines on mining practices, methods, and costs in the United States. The Bunker Hill and Sullivan mines are situated in the western part of the Coeur d'Alene district at Kellogg, Shoshone County, Idaho. The mines were discovered during the summer of 1885 and except for two short periods of labor trouble, between 1890 and 1900, have been in continuous operation. About 575 men are employed at the mine. The production is about 1,400 tons of lead-silver ore per day. This is treated in the company's concentrator and smelter at Kellogg.

Jan 1, 1931

By Thomas C. Ruhe

The Bureau of Mines conducted research to determine the safe operating conditions for using recycled (used) lubricating oil from mining equipment as a partial replacement for diesel fuel to make ANFO-type blasting agents. The use of recycled oil (RO) saves energy, reduces oil imports, and reduces mining costs. Low ambient temperatures may cause these recycled oils to become too viscous for proper absorption by ammonium nitrate (AN) prills and result in poor blast performance, safety hazards, and environmental problems. To help quantify and resolve these issues, viscosity, mixing, and performance tests were conducted at various temperatures. Diesel fuels No. 1 and No. 2 were studied separately and in blends with 25,50, and 75% RO. Good quality ANFO mixes (94-6) were produced with dry absorbent prills and blended fuel (No. 1 diesel plus RO) at temperatures as low as -40°F (-40°C) with 75% No. 1/25% RO, and at -20°F (-29°C) with 50/50. Diesel fuel No. 2 also made good mixes as low as -30" F (-34°C) with 75% No. 2/25% RO, and at 0°F (-18°C) with 50/50.

Jan 1, 2008