Search Documents

By John M. Dower, Ralph W. Plummer, Terrence J. Stobbe, Hyunwook Kim

"The relationship between exposure to coal mine dust and the development of various respiratory diseases is well recognized. The cause of these diseases however. Is still uncertain. To study this cause-effect relationship, It Is necessary to characterize the coal mine dust In terms of the quantity of dust present and mineral content of the dust. Dust samples were collected using a Portable Continuous Aerosol Monitor (PCAM) and 4-stage cassette Impactors at various locations in an upper Freeport seam coal mine In West Virginia. The samples were analyzed using an X-ray microdiffraction film technique and energy dispersive scanning electron microscopy. This paper presents the results of the first phase of this characterization work which Includes determining the size distribution of the dust and the mineral content of the size intervals.IntroductionDiseases associated with dusts in coal mine environments continue to afflict miners in today's modem mines. These diseases still persist because, as Olishifski points out an employee rarely experiences exposures to a single environmental stress but rather to an Intricate Interplay of multiple stresses.(1) In the case of coal mining the multiple stresses are varying sizes of dust particles originating from coal imbedded minerals. Immediate roof strata bottom strata. Incombustible rock and the coal itself. The site of this Intricate Interplay Is the miner's lungs and the resulting diseases are a function of the composite dust exposures.The proper study of coal mine dust toxicity requires that the dusts used replicate existing coal and mineral dust compositions in their relevant size fractions. The purpose of this project is to develop the size and mineral content data necessary to support this ongoing toxicological effort.Existing coal mining standards and regulations also address total and respirable dust exposures. These dust terms refer to both the quality and quantity of the dust segment in the mine atmosphere. Dust quality addresses its coal and mineral content. whereas dust quantity Is described by mass per unit volume (mg/m3) The comprehensive characterization of coal mine dust exposures will enable revision of these standards and regulations to address the specific minerals and size fractions found to be toxic to human lung tissue."

Mar 1, 1989

By Maria I. De Rosa

Table 1 and figure 1 show the number of fires and fire injuries that occurred in underground metal/nonmetal and stone mines by state during 1990-2001. Table 1 also shows the injury risk rates, employees' working hours, and lost workdays. Overall, 65 fires occurred in 20 states; these include 2 fires and no injuries for contractors. Six of the fires caused nine injuries. The yearly average was 5.4 fires and 0.75 injury. Forty-one fires with 2 injuries occurred in metal mines, 14 fires with 7 injuries occurred in nonmetal mines, and 10 fires with no injuries occurred in stone mines. The underground mine fires required 25 mine rescue team interventions and 30 mine/section evacuations. The Ewhr value was 260 x 10° hr (Irr = 0.007), and the LWD value was 83. Idaho had the most fires (eight fires and no injuries), followed by Louisiana (seven fires and two injuries), Michigan (six fires and six injuries), and Missouri (six fires and no injuries). Of these states, Michigan had the highest injury risk rate value (Irr = 0.146). Table 2, partly illustrated in figure 2, shows the number of fires, fire injuries, risk rates, employees' working hours, and lost workdays by time period. The number of fires during the six time periods show an increase during the fourth period followed by a sharp decrease during the fifth period and a sharp increase in the last period. The number of fire injuries show an increase followed by a decrease during most of the periods, accompanied by a decline in employees' working hours during most of the periods; an increase is seen during the third and fourth periods. The In values follow patterns similar to those shown by the injury values. Tables 3-8 show the number of fires by ignition source, method of detection and suppression, equipment involved, location, and burning material by time period. Figure 3 shows the major variables related to fires for 1990-2001. Table 9 shows the number of fire injuries per number of fires causing injuries and total fires by year, ignition source, equipment involved, and location.

Jan 1, 2004

By Joseph C. Zelanko, Anthony T. Iannacchione

One of the most difficult, longstanding engineering problems associated with coal mining is the catastrophic failure of cog mine structures known as bumps. For more than 70 years, researchers and practitioners have assembled a wealth of technical information on coal bumps in an attempt to understand and control them. However, many technical issues raised long ago are still being debated today. This paper examines past experiences and recognizes achievements in the realm of coal bumps. U.S. Bureau of Mines (USBM) researchers collected and analyzed 172 coal bump incident reports and compiled the pertinent statistics into a database. Actual field studied are also discussed. Examination of past experience has shown that there is no one set of defining characteristics that is responsible for coal bumps. In all cases, bumps occur when complex arrangements of geology, stress, and mining conditions interact to interfere with the orderly dissipation of stress. However, it is evident from the database that a tremendous reservoir of knowledge has been established from past experience that has unquestionably limited the severity of coal mine bumps in the United States.

By Douglas A. Donato

This Information Circular presents the MULSIM/PC system of numerical modeling computer programs developed by the U.S. Bureau of Mines. This system consists of four programs: PREMUL, the preprocessor or mesh generator; MULSIM/PC, the actual numerical modeling program (number cruncher); MUL3D, a three-dimensional postprocessor; and MUL2D, a two-dimensional postprocessor. These programs were specifically designed to operate on IBM-compatible (MS-DOS-based) personal computers for easy transfer of this technology to the mining industry and academia. MULSIM/PC uses a subvariation of the boundary-element method, namely, the displacement-discontinuity technique, for linear-elastic geomechanical analysis of mine plans in one or two parallel underground tabular deposits. Results calculated by this technique include stresses and displacements as they relate to changing mine geometries and materials. In addition to describing the MULSIM/PC program and its features, and providing a detailed example model, this report also documents the associated preprocessing and postprocessing programs that are part of the MULSIM/PC system. User's guides for all the programs are contained in the appendixes following the main report.

Jan 1, 1992

By Paul W. Jeran

Subsidence was monitored by the U.S. Bureau of Mines over the ends of longwall panels operating in the Pittsburgh, Kittanning, and No. 2 Gas Coalbeds of the northern Appalachian Coal Basin. The final subsidence over the finishing ends of three panels in the Pittsburgh Coalbed are compared with the subsidence measured over the rib at these panels. The characteristics of subsidence are different. At Mine A, data over the start of a longwall panel shows similar characteristics to the subsidence measured over the rib. Subsidence over the fmishing ends of panels in the Kittanning and No.2 Gas Coalbeds are also different from the subsidence over the rib. The use of a subsidence prediction model based on data gathered over the rib of a panel will not yield accurate results if it is applied to the finishing end of a longwall panel. Acceptable results may be obtained along the centerline over the starting end of a panel.

Jan 1, 1991

By J. N. Geyer

In coal mining it is essential to maintain the roof over working places and roadways in the safest condition possible. To this end every effort should be made to win the coal with the least injury to the immediate roof strata, as broken strata certainly present a greater hazard than a sound roof. The chief causes of injury to the roof in mining are inherent in the method of development and recovery and the blasting practices followed. The first, which may produce severe stresses in the roof, weakening it over comparatively large areas has been discussed in previous papers3 and will not be treated here. The second cause is local in effect, but with the same general method of blasting being employed throughout a mine having uniform roof conditions, similar effects on the roof may be expected. In the Bureau's investigation of accidents caused by falls of roof and coal it has been necessary to make a careful study of blasting practices and their effect on the immediate roof. The purpose of this paper is to show the effect of the observed methods of blasting on different types of roof and to point out methods that have been proved to be least harmful to the roof strata. The data used in preparing this paper have been compiled from reports made by Bureau engineers engaged in the study of falls of roof and coal, and embrace mines opened in the Pittsburgh coal in Ohio and Pennsylvania and the Pittsburgh and Sewickley coals in West Virginia.

Jan 1, 1933

By Frank E. Cash

"INTRODUCTION The producing iron-ore ranges in the Lake Superior district are the Marquette and Menominee in Michigan, the Gogebic in Michigan and Wisconsin, and the Cuyuna, Mesabi, and Vermilion in Minnesota. These ranges produce about 85 percent of the iron ore mined in the United States. The accident experience in connection with this production is better than that of the regions producing the remaining 15 percent. Production and shipments vary slightly from year to year owing to stockpiling underground ore during the winter, or nonshipping, season but closely approximate each other over a period of years. This information circular supplements, combines, and continues the data contained in Information Circulars 7321 3/ and 7410 4/, including statistics for 1946 and 1947.Whereas the title ""Accident Experience"" is used for uniformity and logical indexing throughout this report, ""injury"" will be used as a general term to apply to disabilities of all degrees.During the 8-year period 1940 to 1947, inclusive, 619,054,023 long tons of iron ore was shipped from the Lake Superior district. 5/ Michigan and Wisconsin shipped 117,828,939 tons, or 19.03 percent of the total, and employed approximately 9,260 men. Minnesota shipped 501,225,084 tons, or 80.97 percent of the total, and employed an approximate annual average of 12,260 men. The tons produced and shipped per man employed in Minnesota is much greater than in Michigan and Wisconsin, owing to the large open-cut production in Minnesota."

Jun 1, 1949

By D. A. Paice, A. B. Shimp

A test program was conducted to determine the adequacy of molded case circuit breakers for dc electrical systems in coal mines. Mine electrical system parameters and the most severe operating conditions to be expected were determined. Tests of the interrupting capabilities of several molded case breakers were made under the worst conditions to be expected. Continuous and pulsed current carrying capability of the breakers was also investigated. Breakers from two different manufacturers passed all tests successfully. Based on the results of these tests, a set of guidelines for applying molded case breakers to dc systems has been prepared.

Jan 1, 1975

By Steven J. Page

Accurate measurement of workplace respirable dust concentration is an essential step in eliminating lung disease in any occupational setting. In the United States (U.S.) coal mining industry, this measurement process has relied upon a personal sampler that includes a 10 mm Dorr-Oliver (DO) nylon cyclone operated at a flow rate of 2.0 L min-1 to collect a respirable dust sample. Dust concentrations measured with this sampler are multiplied by 1.38, which was empirically derived, to convert them to measurements approximating the United Kingdom British Medical Research Council (BMRC) definition of respirable dust upon which the health effects of coal mine dust are based. The International Organization for Standardization (ISO) subsequently refined the respirable dust definition and the U.S. National Institute for Occupational Safety and Health (NIOSH) 1995 Criteria for a Recommended Standard presented a conversion multiplier of 0.857 to apply to the 2.0 L min-' DO (in addition to thel.38 multiplier) to obtain equivalent ISO concentrations, as approximated by the 1.7 L min-1 DO. However, the conversion multiplier 0.857 was derived indirectly from a limited size distribution data set rather than a direct comparison of the DO samplers. The present analysis focuses on providing a more accurate conversion multiplier derived from direct comparisons of the 2.0 L min-1 (with 1.38 BMRC equivalency multiplier) and 1.7 L min-1 DO cyclones. A weighted linear regression analysis of this database suggests that a more accurate estimate of the conversion multiplier is 0.815.

Jan 1, 2009

By George McCaa, H. C. Howarth

"During recovery operations following a recent coal-mine explosion, 12 small fires were encountered near the break line of pillar extraction in a large panel. All of the fires except one were quickly extinguished by the rescue and recovery parties. This fire had found its way into a large quantity of loose material at a corner of the cut-through between two rooms, about 100 to 150 feet from the break line of an extensive goaf; had it been necessary to seal the fire, the inclusion of this break line not only would have made the work difficult but would have made the section hazardous as it probably would have given off gas. The fire covered a floor space of about 100 square feet and when discovered was burning briskly, with the flame extending to the roof at a height of 3 or 4 feet; it was the cause of much apprehension on the part of those in charge of the recovery operations and resulted in delaying the work considerablyThe object of this article is to describe in detail the method by which the fire was brought under control and finally extinguished, so that other persons encountering similar conditions may have the benefit of the experience.When the fire was discovered a request for rock-dust, fire extinguishers, and other fire fighting equipment was telephoned to headquarters on the surface. The promptness with which fire fighting equipment and material was provided was a big factor in finally extinguishing the fire and illustrates one of the many advantages of a good organization for fire-fighting. Material was transported in mine cars to a point on the main hauling road about 1,200 feet from the fire. It was then carried to the scene of activity by workmen. The first material to be delivered at the fire was a number of fire extinguishers of various types. The contents of 30 to 35 of these were discharged on the fire and with the aid of a small quantity of rock-dust were sufficient to smother the flame temporarily. It was the opinion of several persons who were present when the fire extinguishers were used that the acid-soda type of extinguisher gave more effective results than the two or three other types used.When the contents of all of the fire extinguishers had been exhausted the fire was temporarily smothered, but as there appeared to be danger that the flame would burst forth again, means for completely extinguishing the fire were"

Feb 1, 1929

Reduce the cost and incidence of low-back pain in underground coal mines through redesign of materials-handling tasks. Background Approximately 25 pct of all injuries in mining involve trauma to the hack. These injuries account for at least 30-40 pct of worker compensation payments made by the industry, are the leading cause of lost work days in mining, and have been estimated to cost the industry $50 million annually. It is clear that the traditional approach to reduce back injuries (i.e., training) has been largely ineffective. Thus, new approaches are necessary to control this problem. This document briefly describes methods that can be used to redesign hazardous materials-handling tasks to reduce the threat of worker injury. Approach A model for redesigning materials-handling tasks is shown in figure 1. The model outlines the sequence of steps that should be followed (and questions that should be asked) when developing new strategies for handling materials in underground coal mines. A critical examination of the current supply-handling system is the first step to developing safer materials-handling procedures. The purpose is to identify hazardous tasks that can be modified to reduce injury risk. Accident analysis (a review of past accident records) and task analy¬sis (usually a videotaped analysis of hazardous jobs or tasks) arc effective methods of distinguishing areas where job redesign is needed.

Jan 1, 1992

By Alan G. Mayton

The Bureau of Mines conducted a study to (1) determine from laboratory tests the feasibility of a photographic method for determining reflec-tances that may be applied to measuring in-mine mineral reflectances and (2) formulate a procedure for collecting and analyzing the data. The method uses a 35-mm camera with automatic flash and a gray-scale re-flectance standard to collect on film the reflectivity data in under-ground mineral mines. After the film is processed, the data on the photographic prints are analyzed in the laboratory with a photometer. Test results show the photographic method can provide values of reflec-tance to within ±5 pet of full scale (full scale = 100 pet). The method's usefulness for determining reflectivity values, within similar limits of absolute percent error at the lower end of the scale, however, has not been completely resolved by the study and consequently warrants further investigation. The method offers an acceptable means for collecting and analyzing reflectivity data for reflectivities at the higher end of the scale, i.e., 50 pet or above; it should be used with caution when reflectivity values are below 50 pet. Four films were evaluated; all gave relatively satisfactory results.

Jan 1, 1987

By R. Karl Zipf, Z. T. Bieniawski

"SummaryAs part of an effort.to understand the mechanics of fine fragment formation in coal, which is important in studies of respirable dust due to mining, fracture toughness measurements and the strain energy density (SEO) theory were applied to calculate the crush zone size under a cutting tool in coal. This · zone is the major source of fine fragments in the 1 to 10 µm size range. The model used in these calculations is a boundary element program containing a failure criterion based on the SEO theory. The boundary element program calculates linear elastic stresses at numerous points in the coal material ahead of a cutting bit. These stresses arc then input to a subroutine called critical ftaw length and orientation (CFLO) which uses the SED theory to determine the CFLO for a small crack at the boundary element stress computation point. The extent of crushing is based on earlier postulates about . the role of inherent flaws in a fragmentation process. To form 1 to 10 µm fragments requires firstly a local stress strong enough to activate flaws with a characteristic length less than 1 to 10 µm and secondly, a flaw density sufficient to provide an average spacing between flaws also on the order of 1 to 10 µm. The locus of active lO µm ftaws represents the maximum possible extent of fine fragmentation in the 10 µm or less size range assuming that a sufficient inherent flaw density exists. The approach offers a first order approximation to the extent of crushing under a tool tip. The size and shape of the crush zone volume is affected by the attack angle and geometry of the tool.IntroductionFine fragment generation in the 1 to 10 µm size range under the action of a generic coal cutting tool may be explained on the basis of fracture mechanics which suggests two major sources of fine fragments: first in a crush zone near the tool tip and second by shear fracturing. along major macrocrack surfaces (Zipf and Bieniawski, 1988a). In this paper, fracture toughness measurements and the strain energy density theory are used to calculate the crush zone size. This zone represents the major source of fine fragments in the 1 to 10 µm size range and understanding the mechanical factors controlling its size represents a first step toward using fracture mechanics to characterize the ·tendency of various coals to produce undesirable fine fragments."

Aug 31, 1989

By E. J. Gleim

In April 1932, the Bureau of Mines published Information Circular 6595, entitled "Data in Reference to Installation of Cables in Shafts and Boreholes", in which were described methods followed in various sections of the United States when electrical circuits are taken into mines by means of cables suspended in shafts and boreholes. In view of the present tendency to extend high-tension cables along entries and passageways from the bottom of the shaft, borehole, or other point of entrance to coal mines rather than over the surface, it is deemed that the various methods of installing such cables deserve careful consideration, particularly in mines in which gas and coal dust contribute to explosion hazards. This is especially true of localities where there is an inclination to restrict the extension of 2,300- and 4,000-volt circuits into the mines. Probably it is feared that accidental contact with the cables of such circuits may result in more serious shock than with lower voltages; also, it is possible that new circuits are regarded merely as explosion hazards additional to those already existing, regardless of the manner in which the new circuits may be installed. It is the firm belief of some engineers that the circuits can be installed so that they will not be damaged by wrecks or roof falls, thereby eliminating the hazard of explosion from this source while at the same time making the chance of accidental contact remote if not impossible. Moreover, some believe that fire hazards from direct-current systems can be reduced by keeping motor-generator sets close to load centers. Thus, although the alternating-current circuits would be lengthened, the size and extent of direct-current circuits would be kept to a minimum.

Jan 1, 1939

By W. D. Walker

All pipelines used to transport liquid fuels over coal mines are potentially hazardous; however, this publication deals only with dangers in transporting gasoline. Since transporting gasoline by this method is an established practice, the hazards connected therewith should he recognized by coal-mine operators and pipeline companies so that every known precaution may be used to reduce and keep the hazards to a minimum. The purpose of this paper is to direct the attention of coal-mine operators and employees, pipeline-company officials, and other interested persons to the explosion and fire hazards that arise from seepage of gasoline into underground mines. A hazard is not only presented in an individual mine when gasoline enters underground workings; but, in cases where mines are interconnected, a hazard exists in mach such mine.

Jan 1, 1954

By H. P. Greenwald

About mid-December 1936, the safety director of a large coal corporation visited the authors at the Bureau's Experimental coal mine to discuss a rock-dust barrier he had invented primarily for use in trackless entries of coal mines. The rock dust in this device was carried in its original paper containers and means were provided for ripping these open so that the dust might be scattered in the path of an explosion. The inventor termed the device a "bag barrier", and this term has been adopted in the present paper for convenience. At that time the device was in an early stage of development, and the inventor felt that the barrier should be tested to determine whether it had enough promise of being successful to justify further development. The matter was taken under consideration and finally three tests were made during the week of February 15, 1937. It was concluded that while the device did stop an explosion in two of the three tests, it was much loss effective than ordinary rock dusting, and that too few data were obtained to permit direct comparison with tests of other barriers. Apparently, the conditions under which the device could, be successful 'Were somewhat limited, out the limits could not be defined without additional tests.

Jan 1, 1938

By B. R. Mohal, F. F. Aplan, S. Chander

"ABSTRACTThe wetting behavior of coal has been determined in the presence of nonyl and octyl series of nonionic surfactants containing polyethoxy groups of different sizes. The wetting behavior was determined by a modified Walker technique and contact angle measurements. The results show that the wetting rate of coal varies with coal rank, structure of the hydrocarbon chain and number of ethoxy groups in the hydrophilic group of the surfactant. A close relationship has been observed between the wetting rates and the short-time advancing contact angles.INTRODUCTIONNonionic surfactants are used in many applications to improve wettability of solids. They can be used as dispersing agents [ 1 ] or dust suppressants [ 2-5 ] and to control the flotation, flocculation, filtration and flowability of particulates. This study was undertaken to study the effect of a series of nonionic surfactants on the wetting behavior of coal. Two series of surfactants, namely, ethoxylated nonyl and octyl phenols were used. The nonyl phenol series contains a linear hydrocarbon chain containing nine carbon atoms ( CH3( CH2 )8-C6H4,- ( OC2H, ) n, where n is the number of ethoxy groups) . The octyl phenol series contains a branched hydrocarbon chain containing eight carbon atoms ( ( CH3 ) 3CCH2C ( CH3)2-C6H4- ( OC2H4) n ).Initial wetting rates — modified Walker techniqueWalker et al. [ 6 ] developed a sink test to determine the wettability of coal particles. In this technique, coal particles are dropped individually onto the surface of surfactant solutions of different concentrations, and the most dilute concentration in which coal would sink ""instantaneously"" is determined. This technique is a variation of a procedure initially developed by Draves and Clarkson [ 7 to determine the effect of surfactants on wettability of cotton fibers. In this procedure commonly known as the Draves test, the concentration of a surfactant required to give a 'sink time' of 25 s is determined.Other investigators have used slight variations of the Walker method to study the wetting of fine particles [ 8-12 ] , by measuring the time for wetting a given amount of powder. There are differences in the manner in which the time of wetting is measured, however. Some investigators measure the time for the last trace of coal to disappear [ 8,11 ] whereas others determine the time for the vast majority of particles to sink [ 10 ] . Some investigators report a wetting rate [ 11 ] which is a value calculated on the basis of the time for the 'last traces of particles to sink'. The differences in choice of criterion for wetting can result in different values for wetting rates as illustrated in Fig. 1 which is based upon our measurements of the amount of powder wetted as a function of time. The procedure for wetting rate measurements is described in the next section. The technique in which time for disappearance of the 'last traces of particles' is determined gives the smallest value for the wetting rate, while the technique in which the time for wetting of the 'vast majority' of particles is determined will give intermediate rates. The terms 'last traces of particles' and 'vast majority of particles' are usually not defined explicitly and can lead to large differences in wetting rates measured by different investigators. Since our measurements show that the wetting rates for an assembly of powder decreases with time, we have used the initial wetting rates to compare the wetting behavior of coal in solutions of different surfactants."

Mar 1, 1989

By Wilson Blake

The Bureau of Mines used a mathematical model based on the finite element method of stress analysis to calculate stresses and displacements surrounding an open pit mine in a gravity-loaded rock mass. Comparison of the finite element solution for a semicircular notch in a gravity-loaded plate with the theoretical solution for a semicircular notch in a plate under uniform compression parallel to the free boundary demonstrates the inapplicability of the latter method to openings at the free surface of a gravity-loaded medium. High stress concentrations are formed at irregularities along the boundary of an open pit in a gravity-loaded continuous competent rock; however, for this type of rock the magnitudes of the stresses are too low to be considered a major factor in open pit slope stability. High stress magnitudes will occur if, in addition to the gravity stress field, a large horizontal stress field exists.

Jan 1, 1967

By Jan M. Mutmansky

"When, in 1973, a limit was placed on the amount of dust in the coal mine atmosphere, restricting the average exposure of a coal miner to 2 milligrams of dust per cubic meter of air (mg/m'), skeptics in the United States and abroad Said the standard could never be achieved. They cited much more lenient standards already established in other countries and refused to believe that the United States could meet the world's most stringent requirements in mines where dust had never before been regulated. Yet 10 years later the goal had largely been achieved and miners were working underground in a cleaner atmosphere than ever before. It was a major achievement and a big stride in what had become a war on coal workers' pneumoconiosis (CWP), the black lung disease prevalent among miners in underground coal mines.Although the health hazards caused by working in a dust-filled mine atmosphere have long been recognized, the problem became particularly acute in this century with the mechanization and increased productivity of underground coal mining. The United States was much slower than some other countries to address the problem of respirable diseases among miners. While dust levels in South African gold mines were first regulated in 1912, in the United States it was only when 476 workers died of silicosis while blasting a tunnel through a mountain near Gauley Bridge, West Virginia in the 1930s that widespread public attention became focused on the plight of workers in dust-filled environments. Another 30 years passed before regulation of dust finally became law in the Coal Mine Health and Safety Act of 1969.With a stringent new standard imposed in all underground coal mines, the industry was faced With the daunting problem of reducing levels of airborne dust from perhaps 6.5 mg/m' to 2 mg/m', in an inherently dusty operation carried out in the close confines of underground passageways. Most of the coal dust is made by the cutting operation in which the continuous miner or longwall machine can produce several thousand milligrams of respirable dust for each ton of coal mined. Other dusty operations such as drilling holes for roofbolts, loading and unloading coal on shuttle cars, and the operation of conveyor belts contribute to the overall problem.Since the institution of the new dust control standards, a number of strategies have been adopted for reducing the coal dust in the mine atmosphere. These strategies involve engineering and design improvements that help lo prevent the generation of particles, keep particles of dust from becoming airborne, carry dust away from the working area, and isolate the dust from the workers in the mining operation. These procedures have been pursued vigorously by the Bureau of Mines, and many successful methods have been developed to reduce the mass concentration to which the workers are subjected. The mining companies were reluctant at first to confront the problems but after a period of trials and gradual improvement, they joined with others in the fight to reduce the dust concentrations in the working place."

Jan 1, 1990

By By Staff

"These proceedings consist of papers presented at a Bureau of Mines Technology Transfer Seminar on postdisaster survival and rescue research. Several seminars are held each year to bring the latest results of Bureau research to the attention of the mining industry as quickly as possible.INTRODUCTIONThe postdisaster research program is directed toward research and development of technology and equipment that increases the chances of a miner surviving or being rescued after an underground mine disaster. A disaster is an accident of major proportions, and it may result in the entrapment of miners whose normal egress from the mine is cut off. This often necessitates a rescue operation and a means of keeping the trapped miners alive while they await rescue. The Bureau is currently pursuing research to develop the technology that will enhance the ability of miners to survive such an occurrence. The research is divided into two basic problem areas, survival and rescue. Both areas are concerned with the inability of miners and rescue teams to cope with the postaisaster environment, such as toxic gases, unstable roof conditions, water flooding, and lack of oxygen. In addition, research is also conducted to find ways of locating and quickly reaching trapped miners. Most of the research conducted by the Bureau has been directed toward the postdisaster problems associated with coal mines. However, most of the research results are also applicable to noncoal mines as well.The papers presented in these proceedings address some of the recent research conducted by the Bureau of Mines that has been directed toward the postdisaster problems outlined above. The topics covered range from an overview of the technology developed for oxygen selfrescuers to training programs for mine rescue. Any questions or comments pertaining to this research are encouraged and appreciated. Open file report (OFR) references in the proceedings listed as available from NTIS may be obtained from the National Technical Information Service, Springfield, Va. 22161, and are also available for reference at Bureau of Mines facilities in Denver, Colo., Twin Cities, Minn., l3ruceton and Pittsburgh, Pa., and Spokane, Wash.; the Department of Energy facility in Morgantown, W. Va.; the National Mine Health and Safety Academy, Beckley, W. Va., and the National Library of Natural Resources, U.S. Department of the Interior, Washington, D.C."

Jan 1, 1982