Search Documents

By A. P. Grossman

'This report was prepared by Shell Oil Company, Mining Ventures Department in accordance with Cooperative Agreement No. 14-09-0070-b53 dated September 10, 1976, between the United States of America, Department of the Interior, Bureau of Mines and C(b) Shale Oil I Project, Ashland Oil Inc., Shell Oil Company, Operator. After completion of this report the Shell Oil Company withdrew from participation In the C(b) Shale Oil Project and advised the Bureau of Minus that plans for publication of this report had also been withdrawn. The Bureau of Mines acting under terms of the Cooperative Agreement hereby releases this report for general information.

Jan 1, 1976

By W. E. Lamont

Flotation studies of phosphate-bearing waste pond materials, low-grade washer products, and raw ores, all from the Tennessee brown phosphate district, showed that these types of materials could be treated without des liming to recover high-grade phosphate concentrates. The investigation showed that fine grinding before flotation was a requisite for increased recovery of the phosphate values and that the optimum pH conditions were in the range of 10.0 to 10.5 when using anionic collectors. Multiple-cleaning of the rougher phosphate concentrate was required to produce high-grade concentrates. Phosphate recoveries ranged from 60 to 82 percent and were inversely related to the grade of concentrate produced.

Jan 1, 1972

Reduce the hazards to which mine personnel are exposed by providing safer procedures for removing dragline wire rope terminations. Background The termination points of wire ropes used on draglines consist of a wedge and socket that lock the rope in place through friction. These components must be separated when the wire rope is changed. At present, the cannon method is the most common procedure used to accomplish this. However this method, using a small cannon and primer (detonator) cord to propel a steel projectile that will knock the wedge out of the socket, has the potential of causing injuries to mine personnel and damage to equipment. The Bureau of Mines, has devised safer, and equally efficient methods of removing wire rope terminations. The Bureau began by studying the cannon method, its merits and draw-backs. Safety guidelines were then developed for the cannon method, and two alternative methods-the pendulum ram and hydraulic pusher-were devised and tested. The Cannon Method The steel projectile used to separate the wedge and socket in the cannon method was found to be very effective. However, the method poses the inherent hazards of any explosive de-vice-hazards that could be increased by lax work procedures. There is no strict uniformity in the manufacture of the cannon or in the work procedures used in the mines employing it. Hazards could be reduced, or even eliminated, with adaption of certain manufacturing and work-procedure guidelines, such as 1) making the cannon and projectile de-signs, as well the work procedures used, uniform, 2) ensuring separate loading of the charge and detonator with insertion of the detonator through a separate port, 3) connecting electrical firing circuits only after the charge and projectile are loaded and the cannon is placed in its final firing position, 4) using approved detonating devices, 5) anchoring the cannon before firing and, 6) placing armor netting over the cannon before detonation.

Jan 1, 1986

By B. J. Scheiner

The Federal Bureau of Mines investigated an electrolytic oxidation procedure for extracting lead, zinc, copper, and silver from lead-zinc concentrates. Concentrates slurried in brine were pumped through the anode compartment of electrolytic cells equipped with selective ion diaphragms. Hydrochloric and hypochlorous acids generated in the anode compartment converted the metal sulfides in the concentrates to soluble metal chlorides, sulfate ion, and elemental sulfur. Metal extractions of 92 to 100 pct were obtained from lead-zinc concentrates at an energy consumption ranging from 1.5 to 5.0 kW-hr/lb metal extracted. Sodium hydroxide was formed in the cathode compartment at a current efficiency of >99 pet. Silver and copper were extracted from refractory tetrahedrite minerals, but the process entailed a relatively high energy consumption. Sealing the top of the diaphragm cell utilized the chlorine more effectively, thereby reducing energy consumption 10 to 50 pct.

Jan 1, 1975

By G. R. Hopkins

According to reports received by the United States Bureau of Mines, Department of Commerce, as of January 1, 1929, there were 2,205 cracking units completed or being built in the United States, with a total daily charging capacity of 1,476,874 barrels. A similar survey of a year ago showed 2,334 units of 1,288,000 barrels total capacity. This indicates that despite a decrease in. number of units, there was a material increase in capacity. The year 1928 was, in general, an important one for the cracking branch of the industry. Gasoline consumption reached record levels, prices were higher than in 1927, and it is probable that in the late months of the year the cracking plants were operating very close to capacity.

Jan 1, 1929

By T. E. Ackman

The Bureau of Mines conducted a study of current trends in methods employed by the coal industry to dispose of acid mine drainage (AMD) treatment sludge. Thirty-three AMD treatment plants, operated by 11 Pennsylvania coal companies, were randomly surveyed. These plants provided data for calculating sludge volumes, as well as information on sludge settling, transportation, and disposal. Onsite visits allowed observation of problems associated with the various methods of sludge disposal: (1) disposal into a deep mine, (2) permanent retention in ponds, (3) disposal at an active coal refuse area, and (4) onsite burial. Method 1 is the most frequently used and the most environmentally sound. It is apparent, based on this representative sampling of AMD treatment plants, that the magnitude of sludge production is such that an aggressive and directed effort in reduction of sludge volume is seriously needed. The areas of major concern are (1) the amount of surface land required for sludge storage and disposal, (2) reclamation of these disturbed surface areas, and (3) effective and efficient means of removing, transporting, and disposing of AMD sludge. In this report, an engineering approach to the practical problems associated with the existing disposal methods is presented, together with recommendations for future research.

Jan 1, 1982

By D. G. Foot

The Bureau of Mines devised a direct flotation method for recovering potash from carnallite (KC1?MgC12?6H20) ore characterized by a high content of water-insoluble impurities. The method includes (1) a decomposition leach of the carnallite, (2) flocculation-depression of the insoluble slimes, (3) potash rougher, cleaner, and recleaner flotation, and (4) final product leaching. The technique eliminates the necessity for removing the water-insoluble slimes by mechanical or flotation de-sliming. Laboratory results demonstrated that the direct flotation procedure, when compared with conventional techniques, yielded equivalent or improved flotation results with equal or less reagent consumption. Locked-cycle testing of the direct flotation method recovered 87.8 pct of the potassium in the flotation feed in a final product containing 60.6 pct K20. A flowsheet incorporating the carnallite leaching-potash flotation procedure is presented.

Jan 1, 1982

By Terry S. Cory

This report covers magnetic field strength measurements vs range and frequency in low-medium coal mines. Both quasi-conductor-free and conductor-proximity areas were investigated. The program covered 5 mines, 4 seams, 6 measurement sets, and 3 geographic areas. The results have been summarized in terms of maximum communication range expected per seam and noise condition. Scatter gain is further explored as a simple measure of energy coupled to conductors.

Jan 6, 1978

By Seth C. Schaefer

The Bureau of Mines investigated thermodynamic properties of Mn304 (manganomanganic oxide) and Mn203 (manganese sesquioxide). The standard Gibbs energies of formation (?Gf°) of Mn304 and Mn203 from their lower oxides were determined with high-temperature galvanic cells using stabilized Zr02 (zirconia) as the electrolyte. Potential measurements were obtained for the cell Pt, MnO, Mn304//Zr0 2//02(g, 0.0112 atm), Pt, with the overall cell reaction 6Mn0(c) + 02(g, 0.0112 atm) = 2Mn304(c), where- 02 refers to indicated partial pressure of oxygen at the reference electrode. Similar measurements were obtained for the cell Pt, Mn304, Mn203//ZrO2//02(g, 0.0115 atm), Pt, with the overall cell reaction 4Mn304(c) + 02(g, 0.0115 atm) = 6Mn203(c). Equilibrium oxygen pressures for the Mn0-Mn304-02 and Mn304-Mn203-02 systems were measured and may be expressed for the respective systems as [23,400 109 P02 T + 11.91 (764.9 - 1,208.6 K) and log p02 = - 11,957 + 9.66 T (968.6 - 1,208.2 K),] where pressure (p02) is in atmospheres and temperature (T) is in kelvins. Standard thermodynamic properties of Mn304 and Mn203 were derived from these measurements and auxiliary thermodynamic data from the literature.

Jan 1, 1982

By D. R. Dolinar, J. Pablic, D. C. Oyler, T. P. Mucho

At a mine in central PA, high horizontal stresses have caused long running roof falls resulting in hazardous conditions for the miners and the premature abandonment of panels. Because of these conditions, the mine requested assistance of the National Institute for Occupational Safety and Health (NIOSH) in utilizing the 'advance and relieve method to mitigate the affects of horizontal stress on the mine roof. "Advance and relieve" mining involves the removal of a pillar or a portion of a pillar during development, thereby creating a cave along one side of the panel. Following cave development, the horizontal stress is relieved over the workings adjacent to the cave in the active panel. The mine has used this system in three panels with a significant reduction in stress damage and no large roof falls.

By A. F. Colombo

In an effort to maintain an adequate supply of iron to meet national economic and strategic needs, the Bureau of Mines, U.S. Department of the Interior, is conducting research on methods for beneficiating the oxidized taconite resources located on the western Mesabi range in Minnesota, thus expanding domestic iron ore reserves. The selective flocculation and cationic flotation process was investigated in a pilot plant using an ore feed rate of 410 kg/hr (900 1b/hr) and 88 percent recycled water. Lime and a cationic flocculant were used to clarify the waste slurries treated in the water reclamation circuit. An oxidized taconite assaying approximately 36 percent Fe yielded concentrates averaging 63.5 percent Fe and 4.3 percent SiO2 and having an average iron recovery of 84.4 percent. The estimated reagent cost per tonne of concentrate was approximately $1.10. In an attempt to recover more of the iron lost in the flotation tailing, wet high-intensity magnetic (WHIM) separation was incorporated in the pilot plant circuit. The flotation concentrate grades obtained from beneficiation circuits with and without WHIM scavenging were similar, but when WHIM separation was used the overall iron recovery was increased by 2 to 9.5 percent, depending on the iron assay of the flotation tailing.

Jan 1, 1978

By R. D. Leitch

From time to time the Bureau of Mines has received requests from persons who wish to destroy unwanted explosives, and although the information that follows has been accumulated from sources considered reliable,4/ the. Bureau of Mines assumes no responsibility for accidents that may result from following the suggestions offered. Explosives to be destroyed may be fresh material from damaged packages, usable material for which there is no further need, or material that has deteriorated either from natural aging or from improper storage to the point where it is unfit for use.

Jan 1, 1945

By Richard L. Rains

The 15,770-acre Worm Creek Roadless Study Area is in southeastern Idaho about 8 miles (mi) west of the northern portion of Bear Lake. U.S. Bureau of Mines personnel examined the roadless, area during the summer of 1984. No mineral resources were identified within the study area. There were no mines or mining claims in the study area in 1984. However, the study area is blanketed with oil and gas leases, but no known productive horizons have been identified within nor nearby. The roadless area is in the Cordilleran fold-thrust belt and is underlain by Paleozoic and Mesozoic marine strata more than 50,000 feet thick. The trace of the Paris thrust fault is 2 to 3 mi east of the study area and has an eastward displacement of about 4 to 7 mi.

Jan 1, 1985

By Paul Biggs

This Bureau of Mines report provides information on 138 waterflood projects in Wyoming. Injection was in 25 producing zones and 65 fields. Specific data presented include field location, discovery and development, water supply and injection, oil and water production, estimates of oil in place, and oil recoveries by primary and secondary methods. The 138 projects studied will, if successful, recover about 800 million barrels of secondary oil. Almost all of the injection water is from deep water wells.

Jan 1, 1970

By W. K. Tolley

This report presents data collected during research by the Bureau of Mines on corrosion of grinding media. Corrosion rates of eight alloys commonly used in grinding media were tested in synthetic mill water using an ultrasonic grinding device especially designed for this work. Electro-chemical measurements showed variations in corrosion rates for these alloys between 9.8 mpy for medium-carbon steels and 0.14 mpy for high chromium white irons. Bureau data are discussed along with data from the literature to indicate that corrosion causes less than 10 pct of the wear of grinding media in commercial grinding mills. A comparison of corrosion rates for various types of grinding media shows that alloying elements and electrochemically active inclusions in steel affect the corrosion behavior of the media.

Jan 1, 1984

By C. Özgen Karacan

Degasification and methane control in underground coal mining is an important area augmenting conventional ventilation in order to prevent possible fires and explosions due to excessive methane emissions. Coal bed reservoir engineering has been applied for many years to coalbed methane production. In recent years, modeling the flow and draining methane, not only from coal bed itself but also from the overlying strata, have been recognized as important areas of expertise for supplementing underground ventilation. This paper demonstrates the applications of coal bed reservoir engineering and modeling techniques for optimizing and controlling methane emissions in longwall and continuous miner sections. Practical applications and some considerations are presented for reservoir modeling, borehole performances, and face emission predictions for various coal bed and borehole configurations. A section on field reservoir studies and well bore log analyses for methane control are also presented as a complementary way of controlling methane and optimizing ventilation.

Jan 1, 2009

By W. A. Jacob, E. W. Dean

The Pittsburgh petroleum laboratory of the Bureau of lines has recently developed an improved method for the determination of water in pctroleum emulsions. It has been described in detail in an article entitled "A convenient method for the determination of water in petroloum and other organic emulsions" by E. W. Dean and D. D. Stark (Jour. Ind., and Enc. Chem. Vol. 12, ſay, 1920, page 436). It is essentially a modification of the familiar procedure of "distillation with an iniscible solvent", the improvement consisting in the use of apparatus that is rºck more convenient than any previously employed. The method has been used with marked success in the Bureau's laboratories for a period of about a year and has also been tried with equal satisfaction by a number of other laboratories. It has been most extensively employed for determining the water content of heavy fuel oils but has been applied also to several other types of emulsions, including shale oils, tars derived from coal, greases, and mixtures of powdered coal, oil and water. The Bureau has received a number of requests for information regarding commercial sources for the apparatus used, and having been assured of the value of the method, has taken steps to render it available for general use. - The equipment is, with the exception of two items, made of parts that are obtainable from the ordinary stock of chemical supply houses. The two exceptions are (1) the so-called "distilling tube receiver" and (2) the electric heater. The former is an essential part of the equipment; the latter is a convenient ac cessory but it can if necessary be roplaced by a gas burner. Efforts on the part of the Bureau staff to ronder these two items of apparatus available for purchase from supply houses, or for production by the user are hero described.

Sep 1, 1920

By J. B. Gayle

Numerous investigators have studied the addition of inert4 substances to coking blends. Generally, the results have yielded trends applicable only to the particular coals and inerts studied. Recently, somewhat more general results were obtained for cokes produced from blends containing added inerts, using the sole-heated oven. The present investigation represents an extension of this work to include a wider range of inerts and to determine the applicability of the various conclusions to cokes produced with the Tuscaloosa oven. The results indicated that an increase in dry-coal charge density of 1 pound per cubic foot (p.c.f.) caused a corresponding change in the hardness (1/4-inch tumbler index) of Tuscaloosa oven cokes of 0.9 percentage points. This value compares favorably with the value of 0.7 determined previously for the sole-heated oven and Bureau of Mines-American Gas Association (BM-AGA) retort.

Jan 1, 1961

By G. A. Apell

The presence of considerable mineralization at the surface together with other favorable conditions suggested inclusion of the Nigger Jim diggings area in a comprehensive study of shallow lead deposits in southwestern Wisconsin. The area, which was the site of considerable shallow development some 60 to 70 years ago, offered the possibility of substantial quantities of lead at near-surface horizons. The investigation included completion of 30 churn-drill holes totaling 1,808 feet of drilling, 2 diamond-drill holes totaling 164.5 feet of drilling, and 25 feet of test pitting in two excavations. The degree of mineralization was determined in an area l,500 feet long and 150 to 300 feet wide along a mineralized trend that has not been investigated beyond the limits of the zone drilled by the Bureau of Mines.

Jan 1, 1948

By A. B. Hooker

Since man first mined underground, there has been need for adequate illumination; this need has never been fully supplied. At first, suitable lamps were not available. Gradually they have been developed, but along with that development the need for better and better lamps has continued owing to the following conditions and factors: 1. Increasing hazards from gas and dust ignitions. 2. The speeding of operations with mechanized mining, which necessitates greater visibility. 3. A demand that cleaner coal be loaded, which requires higher levels of illumination. 4. The cost of compensation for injuries that has created a demand for better illumination and safer lamps. Use of better lamps has been retarded by: 1. Prejudice and resistance to change on the part of the workers in some districts. 2. The cost and upkeep of the lamps. 3. The present types of lamps, while a great improvement over the old lamps, do not entirely fulfill the requirements for a safe and efficient light for underground workers.

Jan 1, 1938