Search Documents

By D. E. Stone

Solid and liquid impurities must be removed almost completely from synthesis gas for the production of synthetic liquid fuels because of their effect on the synthesis catalyst and turbocompressors. The maximum permissible concentration of dust has been set at 0.05 grain per 100 cubic feet.5/ This is one part per million by weight, or about the same concentration as in average city air. The cost of synthesis gas is estimated to constitute 60 to 70 percent of the total cost of the synthetic liquid fuel. For this reason this station is developing processes using coal instead of the more valuable coke as raw material, which promises reduction in cost of the synthesis gas. This, however, increases the difficulty of attaining the above dust value. As failure of the dust-removing equipment to produce high-purity gas may ruin valuable equipment within a few minutes, it is imperative that a reliable and continuous method be obtained for determining such extremely low concentrations .of dust in the purified gas. A suitable device must also instantly sound an alarm and, if necessary, automatically actuate the proper valves to prevent damage. The Ess Instrument Co. designed and built an instrument which they believed might fulfill these specifications. It' continually compared, by means of photoelectric cells, the intensity of a light beam passing through the gas and a similar beam passing through clean air. For maximum sensitivity, the photocells were connected back to back, i.e., anode to cathode and cathode to anode. The difference in voltage produced by the two cells was amplified and operated an indicator.

Jan 1, 1951

By Alfred E. Schwaneke

The surface tension from 240° to 844° C and the density from 236° to 583° C of 99.999 percent purity liquid tin has been measured using the maximum-bubble-pressure method. Results for surface tension (y) show y (dynes/em) = 566.84 -4.76 X 10-2 T (° C) with a standard error of 1.9 dynes/cm. Results for density (p) show p (g/cm3) = 7.16 -6.3 X 10-4 T (° C) with a standard error of 0.012 g/cm3. Comparisons with other data found in the literature are discussed. The experimental results are considered to be as good as any data presently available.

Jan 1, 1970

By G. E. McClelland

The Bureau of Mines investigated chemical methods for producing high- purity gold from precious-metal-bearing zinc precipitates and steel wool cathodes. Precious-metal-bearing zinc precipitates and steel wool cathodes are unrefined products from conventional cyanidation and heap leaching-cyanidation operations. The zinc precipitates contained 14,40 pct Au and 0.35 pct Ag. The precious-metal-bearing steel wool cathodes contained 20.65 pct Au and 4.84 pct Ag. The precipitates and cathodes were treated with dilute acid to solubilize the silver and/or base metals. The gold-bearing residue was leached in dilute aqua reqia to solubilize the gold. High-purity gold was precipitated from the aqua regia solution with oxalic acid, sulfurous acid, sodium bisulfite, and gaseous sulfur dioxide. The leaching-precipitation experiments recovered 99.9 pct of the gold. The gold precipitates ranged in fineness from 997 to 999 fine. The chemical refining method provides a viable technique for the smaller operator to produce high-purity gold without using pyrometallurgical refining methods.

Jan 1, 1985

By Gregory J. Chekan

In This Chapter [Drilling, blasting, and crushers Diesel particulate Enclosed cabs Ventilation with jet fans Stopping construction methods Propeller fans as main fans] This chapter explains how to control dust in large-entry stone mines, including both silica dust and diesel particulate. Most stone mines are limestone mines, but a substantial minority are marble, sandstone, and granite mines. These mines differ from most others in that entry widths are 30 ft or more and entry heights are 25 ft or more. Such mines, developed with room-and-pillar methods, have large open areas that can make ventilation and dust control more difficult. Because of the difficulty of ventilating stone mines, improved ventilation is a major focal point of this chapter. However, the chapter also covers the control of dust from drills, blasting, and crushers. Another part of the chapter covers enclosed cabs, an effective dust control technique for some workers. BACKGROUND The major dust compliance problem in stone mines is caused by silica (quartz) in the rock. Mines in high-silica rock, 8% or more, are far more likely to have a dust problem than those where there is less silica. Geographically, the limestone in the Northeastern and South Central United States has higher silica than the rest of the country. Chekan and Colinet [2002] have analyzed Mine Safety and Health Administration (MSHA) dust sampling results [MSHA 2001] from the stone industry. They have concluded that, on average across the United States, the workers exposed to the highest dust concentrations are rotary drill operators, front-end loader operators, truck drivers, and crusher operators. However, there are many regional differences. Also, occupations that work outside of cabs, such as blasters, roof bolters, and laborers, can be exposed to high dust levels.

Jan 6, 2003

Commodities statistics and other information are available through the following three systems: Internet Access: To access the USBM Gopher server on Internet, connect to: gopher.usbm.gov port 70, using gopher client software. Or contact the Systems Administrator for technical questions: Matt Klevemann, 412-892-6499 (klevemmc@miner.usbm.gov) These USBM materials are available on Internet, with more to come in the future: Publications and other research findings, including this bimonthly publications list, newsletters, tech transfer updates, environmental technology research, health and safety information. USBM software products Media materials and speeches. Mines Data: Computer bulletin board. Log on via modem through 202/501-0373, or call 202/501-0406 for technical assistance. Mines FaxBack Return fax service. 1. Use the touch-tone handset attached to your fax machine's telephone jack. (ISDN [digital] telephones cannot be used with fax machines.) 2. Dial 202/219-3644. 3. Listen to the menu options and punch in the number of your selection, using the touch-tone telephone. 4. After completing your selection, press the start button on your fax machine.

Jan 1, 1995

By Lisa Steiner, Robin Burgess-Limerick

In 2004, underground coal mines in the United States reported 3,405 injuries to the U.S. Mine Safety and Health Administration (MSHA). Of these, 17 percent were associated with the use of bolting machines, 8 percent with continuous miners, and 4 percent each with scoop/load-haul-dump (LHD), shuttle cars and personnel transport. Analysis of the injury narratives identified five hazards that required attention. They are rock falling from supported roof inadvertent or incorrect operation of bolting machine controls, handling continuous miner cable, collisions while driving underground vehicles and driving or traveling in underground vehicles on rough roadways. The rate of lost-time injuries has steadily decreased during the past 10 years (from more than 10 per 100 FTE in 1995, to six in 2004). However, underground coal mining remains a hazardous industry. One of the contributors to this elevated injury risk is working with or near underground coal mining equipment. Roof bolting machines and continuous miners have been consistently identified as high risk equipment. They account for approximately 24 percent of all injuries to underground coal miners (Sanders and Shaw, 1989). LHD's, shuttle cars and personnel transports are also associated with injuries in underground coal mines (Burgess-Limerick, 2005). Conventional analyses of injury statistics typically provide tables detailing the breakdown of injuries by body part nature of injury or mechanism of injury. Such analyses are worthwhile and may be helpful in tracking broad trends over time. Further information is available in the narrative text field completed for each injury reported. The detail contained in these narratives varies. However, they generally provide some insight into the causes of the injury, such as the activity being performed at the tune of

"The Generic Mineral Technology Center on Respirable Dust was established in August 1983, at the request of the Bureau of Mines, to conduct research that affords ""...each miner the opportunity to work underground during the period of (his/her) adult working life without incurring any disability from pneumoconiosis or any other occupational disease"". The Center consists of the Mining and Mineral Resources Research Institutes (MRI) of The Pennsylvania State University (PSU) and West Virginia University (WVU) in association with the MRIs of the Massachusetts Institute of Technology (MIT) and the University of Minnesota (UMN). (FIGURE 34) Michigan Technological University (MTU) is also affiliated with the Center in the area of diesel particulates.The Center brings together experts concerned with particles causing potentially disabling or fatal diseases including pneumoconiosis (""black-lung""), silicosis, and asbestosis. The latter is of deep concern not just to workers in the mineral sector of the economy but also to the general populace. The primary goal of the Center is to reduce the incidence and severity of respirable dust disease through advancing fundamental understanding of all aspects of respirable dust associated with mining and milling, and the interaction of dust and lungs. The research program of the Generic Mineral Technology Center explores these scientific, engineering or medical concerns with the objective of refining existing strategies and developing new respirable dust control techniquesand technology that are consistent with the fundamental dust-lung interaction processes that lead to mine worker disability. The work concentrates on five areas (FIGURE 35):"

Nov 1, 1988

As part of the Bureau of Mines subactivity in secondary resource recovery and to expand the Nation's mineral base, the Tuscaloosa Research Center made characterization and preliminary beneficiation studies of the waste residues from various coal-conversion processes: from pilot plant tests of the Synthane process for coal gasification, the Synthoil process for coal liquefaction, and the solvent-refined coal (SRC) process for sulfur removal from coal. Those coal conversion processes selected for this study were based on the availability of pilot plant samples. Physical, chemical, and mineralogical examinations of the wastes made to determine the mineral content prior to physical beneficiation tests indicated that in addition to significant quantities of carbon, some trace elements offer potential for concentration.

Jan 1, 1980

To restore ventilation and prevent the accumulation of explosive or toxic gases by quickly installing substitutes for stoppings blown down by an explosion. Approach Temporarily replace blown down stoppings with a parachute-shaped brattice which can be erected in minutes. How It Works The self-sealing brattice is secured to the roof, ribs and floor by anchoring its nylon edge strip at several points using extensible poles, shads, or available projections such as roof bolts. The air pressure in the entry pops open the chute of lightweight sailcloth, forcing it tightly against floor, roof and rib. See Figure 1. This emergency brattice has been tested at two locations in the Bureau's Experimental Mine at Bruceton, Pennsylvania. In a test last December, one MESA inspector wearing full rescue apparel (including self contained breathing apparatus) installed a self sealing brattice in an entry at the Bruceton Mine. Although he did not have any previous experience with the device, he easily erected it in slightly less than 10 minutes, using two extensible supports (pogo sticks). Research to improve and refine the self-sealing brattice is continuing.

Jan 1, 1977

By S. J. Pearce

The Bureau of Mines has prepared, as circumstances have dictated, a series of schedules setting forth the minimum requirements that various types of equipment should meet to be considered safe and satisfactory for use under certain hazardous or unhealthful conditions. These schedules cover a wide variety of devices ranging from explosives to electrically operated mine locomotives. This paper discusses the functions and operations of schedules under which respiratory protective devices are tested and approved. It emphasizes that the aim of the Bureau respirator-approval system is to make available to the public respirators that meet definite performance requirements. The responsibility of the respirator manufacturer in pre-testing the device and in maintaining its quality after it is approved are explained. Aid is provided for the user in selecting the proper device for specific application, and a plea is made for better education of all concerned in the proper use of the devices. DISCUSSION Provisions have been made for testing and approving the following types of respiratory protective devices: Self-contained breathing apparatus,2/ supplied-air respirators,3/ gas masks,4/ dispersoid respirators,5/ and chemical-cartridge respirators.6/ These devices are tested at the Central Experiment Station of the Bureau of Mines in Pittsburgh, Pa. Self-contained breathing apparatus is tested by personnel of Health and Safety District B; other types of respirators are tested by the Branch of Health Research.

Jan 1, 1957

By Joseph J. Wallace

1. From the standpoint of known recoverable reserves, the following is the order of importance of the beds: Upper Kittaoning, Lower Kittanning, Upper Freeport, Lower Freeport, Middle Kittaning, Clarion, Pittsburgh, and Redstone. 2. mown measured and indicated reserves in all beds, based on a minimum thickness of 14 inches and on 1,800 tons per acre-foot of coal in place, me estimated at 1,859 million short tons as of January 1, 1952. Of this, 1,351 million short tons me in beds 28 inches and more thick. Areas in each bed were omitted from the estimates because available data relative to the bed characteristics are too meager to make an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1953

By J. B. Gayle

A 1/2-ton experimental coke oven was installed ac the Bureau of Mines Southern Experiment Station, Tuscaloosa, Ala., in 1948. Designated as the Tuscaloosa oven, this unit features a 17-inch carbonizing chamber, globar heating elements, and silica-brick walls designed to simulate as closely as possible the carbonizing conditions for commercial slot-type ovens. Because of the small force exerted on the oven walls in most tests conducted to date (probably owing to the practice of charging coals and blends at a moisture content approximating that normal to commercial plants operating in this district), little information has been obtained about expansion properties. Two sole-heated ovens have therefore been constructed and used as supplementary equipment for determining the expansion properties of coals tested in the Tuscaloosa oven. The reasons for constructing the Tuscaloosa oven, the details of design, the operating, characteristics of the oven and the reproducibility of results have been discussed in previous publications. 3 4 5/ The present report deals with the effects of substituting various high- and low-volatile coals for components of a selected base blend carbonized under conditions similar to those normally used for producing foundry coke. Results of tests of 11 coals and 14 blends indicate that several blends tested rave cokes having physical properties very similar to those produced from the reference blend.

Jan 1, 1957

By J. D. Davis

Coke Since the beginning of manufacturing of metallurgical coke in the United States, which dates from about 1859, Pennsylvania has main tamed supremacy in coke production Available statistics for the year 1880 show an output of 3,338,300 short tons, which was neatly trebled by the end of the succeeding 10 years. From this time on the increase was steady, though not rapid, and in 1922 the total production was 13,991,892 tons, which is approximately 37 per cent of the total coke production of the United States. The main reason for the rapid development of the coke industry in Pennsylvania lies in the abundance of coals particularly adapted to beehive coking, for which purpose the Pittsburgh bed in the Connellsville district has long been looked upon as standard At first practically all metallurgical coke was made in beehive ovens, the only exception being the short lived and wasteful method of coking in piles, byproduct owns did not make then appearance until after 1893 The suitability of a beehive coking coal cannot be accurately predicted from its chemical analysis, but it can be said, perhaps, that the volatile matter should be about 32 per cent, and that the oxygen content should not be mole than 10 pet cent or less than 4 per cent The sulphur and phosphorus content should be small-not over 1 25 per cent sulphur and under 0 02 pen cent phosphorus-and the ash content should not be over 7 per cent The Pittsburgh bed at Connellsvnlle fills these requirements well, as may be seen from the following representative analysis. Analysts of coal from Pittsburgh bed Moisture 1 70 Volatile matter 31 10 Fixed carbon 59 80 Ash 7 40 Sulphur 0 85 B t u 13,990

Jan 1, 1928

By Franklin D. Cooper

The value of nonfuel mineral raw materials produced in the United States in 1978 was $20 billion. In 1979, total value increased to an estimated $24 billion, up 20% from 1978. Of the principal metallic ores produced in 1979, about half showed increased quantitative output and all showed increased value per ton compared with that of 1978. Most nonmetallic commodities showed increases in quantitative output and in average value per ton. Because of its decreasing share of the world market, the domestic mineral industry's concerns were the increasing costs of capital, labor, and energy; withdrawals of public lands from mining; and the increasing cost of environmental regulations that tended to deter or delay investment in the Nation's capacity for producing essential minerals.

Jan 1, 1980

By R. Hogg, J. M. Mutmansky, E. Kaya

"Characterization of the size, shape, chemical composition, and mineralogical content of mine airborne dusts generally requires a larger mass of dust particles than is typically collected using traditional sampling devices. In this paper, the general design of a passive dust collector is described and the field results are presented. The collector was constructed of galvanized sheet metal duct with a resin-coated honeycomb to provide an elutriation-type system for particle collection. Several versions of the collector were used in the field portions of the research.The dust samples collected from underground coal mines were found to possess angular particle shapes, relatively consistent size distributions, and elemental compositions that showed relatively little variation, at least for the more prevalent elements. In addition, the distributions of particles sizes obtained from the passive dust collector appear to be similar to those of samples collected at the same time in a conventional personal sampler except that the passive device seems to collect a larger quantity of coarse, nonrespirable particles. Conclusions on the suitability of this dust collector for collecting characterization samples are presented. In addition, the potential for using such a dust collection system for supplying dusts for biomedical research is discussed.INTRODUCTIONRecently, a considerable amount of research effort has been directed toward better understanding of the characteristics of the coal dust generated during the mining process. It is generally believed that dust characteristics play a significant role in the development of Coal Workers' Pneumoconiosis (CWP). In order to effectively protect coal workers from coal dust, it is important to understand the properties of dust, the mechanisms of generation and dust-lung reaction. Conducting research on dust characterization, dust control and the biomedical aspects of dust toxicology generally requires a large sample of airborne coal dust. Unfortunately, current dust sampling instruments are not able to meet this demand because only a few milligrams of dust are collected."

Nov 1, 1995

By J. D. Tolman

In view of present interest in a revival of gold mining enterprises, papers dealing with the development of small gold properties are apropos. The present paper deals with the operation of a small gold property in the exploration and development stage, mining and milling 25 tons of ore daily, and indicates what may he expected in the way of mining costs under northern climatic conditions, by practicing rigid economy, at a property where disproportionate overhead costs are unavoidable bacause of the small rate of production. The output of this prospect is treated in a small amalgamation plant which has been described in a previous circular.. HISTORY Prospecting in the district was begun in 1909, and by 1911 the adjoining mines, Hollinger and McIntyre, were in operation. Actual work was begun on the Rochester claim in July, 1922, and carried on through 1924. The property was closed until 1928 when the present company took it over, together with the other holdings of the Canadel Mining Co. A small mill was started as a pilot plant on March 24, 1929, and is still in operation.

Jan 1, 1931

By S. H. Ash

Unusual mining conditions prevail in the State of Washington because the majority of the coal seams lie on extra steep dips, and the roof and floor of the seams are of such a character as to require an excessive amount of timber- ing. The seams as a rule give off a considerable amount of methane, which makes good ventilation imperative. Due to physical conditions, supervision is costly and travel about the workings is difficult. Because of the facts stated, the accident rate has been above the average, and for some time considerable thought has been given the idea of making promotion of safety in and about the mines a responsibility to be shared equally by the employees and the management. With this idea in mind the legislature of the State of Washington, turing March, 1927, passed laws providing that safety committees be selected to function at the coal mines of the State and at the same time recognizing the fact that first-aid education is an integral part of any safety movement; legislation was passed making it mandatory to have all persons in and about the ines trained in first-aid administration. The provisions of the State mining law3 are as follows: "In every mine a general safety committee shall be selected, composed of the mine superintendent or manager of mines, one man selected by the employees or any association of employees in or around said mine, and a third member selected by these two. "The general safety committee shall elect one of the members to act as chairman and one to act as secretary. The duties of the chairman shall be to preside at all meetings of the general safety committee, enforce its rules and regulations and see that its business is conducted in a prompt and business-like manner. The secretary shall keep an accurate written record of the proceedings of all meetings, conduct its correspondence and post notices of regular and special meetings and other matters pertaining to safety. The duties of the general safety committee shall be to investigate all serious and fatal accidents; make bi-monthly.

Jun 1, 1930

By Raymond B. Ladoo

"The increasing realization of the fire hazards involved in the use of wooden shingles caused the National Lumber Manufacturers' Association to beginsome five years ago a search for a suitable fire-resistant paint. The problem was submitted to the Educational Bureau of the Paint Manufacturers' Association of the United States and work was started by Mr. Henry L. Gardner at the Institute of Industrial Research, Washington D.C. in collaboration with Dr. Herman von Schrenk, a timber expert of St. Louis.The results of this,work have been described by Heckel, in ""Asbestos"", (Heckel G.B., Asbestos in the Paint Industry, Asbestos, Vol. 2, July, 1920,pp.- 5-10).,,who gives the following formula for one of the colors as typical: It will be noted from this formula that ""asbestine"" forms 33% of the total liquid pigment by weight or 31.8% of the solid constituents. Hockel in the article referred to describes this paint,as ""asbestiform"" and assumes since ""asbestine"" is magnesium silicate it must be the chrysetile variety of ""Asbestine"", however, is not asbestos but is a trade name for a fibrous variety of talc mined in the Gouverneur district, St. Lawrence County, New York. This rather natural error persists through the article and credits asbestos with many desirable properties which are characteristics of talc."

Aug 1, 1920

By B. P. Martinez

This report presents the results of a research and development program in recovering waste-rolling oils conducted by the Bethlehem Steel Co., before 1954 at its Sparrows Point plant, Sparrow Point, Md., with the cooperation of the Bureau of Mines, U. S. Department of the Interior, College Park, Md. The objective of the program was twofold: First, to recover oil for reuse in the plant; and second, to stop pollution, by oil, of the stream and harbor areas in the immediate vicinity of the plant. The sequence of the investigations was laboratory and pilot plant studies on sedimentation, simple aeration, and flotation for the separation of oil and water; and construction of a production unit using standard flotation equipment. This work was only preliminary for the Bethlehem Steel Co. and it has continued research on this problem. Recent progress indicates that new, improved processes will soon replace the flotation units described in this report. The first efforts to separate oil and water by simple sedimentation were unsuccessful. To establish the cause of this failure, microscope examinations and measurements were made on cold-reduction rolling mill cooling-water effluents containing oil in suspension. It was discovered that an average oil globule, held in suspension, was only 0.001 inch in diameter and would not coagulate with other globules for normal sedimentation at room temperature. The next step in the sequence of studies was to coagulate the oil suspension by simple aeration with air under slight pressure. The aeration methods studied were effective in removing up to 68 percent of the total oil but were approaching flotation in principle. The final investigation of the series was flotation of the oil in conventional laboratory-size flotation cells. The small-bubble method, without reagents, floated up to 89 percent of the total oil held in suspension and was the process selected for pilot-plant development.

Jan 1, 1959

By B. W. Madsen

Research by the Bureau of Mines has shown that treatment of open pit waste by crushing and sizing followed by flotation of the fines and leaching the coarse fraction results in greater metal recoveries than obtained by leaching only. Tests with a chalcocite-bearing quartz monzonite mine waste sample that had been crushed to minus 6 inches and screened on 1/2 inch yielded copper and silver recoveries of 71 and 22 percent, respectively, by the combined flotation-leaching process, compared with 48 percent of the copper and no silver recovered leaching the run-of-mine material. Copper was more readily leached from the coarse material with the minus 1/2-inch fines removed than from material with the fines included. The improved leaching was attributed to improved permeability and the associated improved circulation of air to the interior of the ore column. Cost estimates showed that the proposed intensive treatment of mine waste will require a greater capital investment and higher annual operating costs than conventional milling and dump leaching process. However, the income from the additional metal production offsets the increase in capital investment and operating costs, resulting in additional profit.

Jan 1, 1975