Search Documents

By Thomas M. Barczak

The Bureau of Mines is conducting research to optimize the capability of mine roof supports so that the selection and design of these supportsare compatible with the conditions in which they are to be employed. This report describes a study that investigates three parameters influencing the load-carrying capability of wood crib supports: height, configuration, and horizontal displacement. Four crib heights, four parallelogram configurations, and three ratlos of horizontal-to-vertical displacements were tested on full-scale wood crib supports in a mine roof simulator. Test results indicated a reduction in load-carrying capability for increases in crib height. Increasing the contact area by changing the intersecting angle between crib blocks to form parallelogram configurations provided a slight increase in load-carrying capability for the first 10 to 12 in of vertical convergence, after which the cribs became more unstable, resulting in significantly less load-carrying capability. Horizontal displacements did not appreciably affect the load-carrying capability of wood crib supports for the range of vertical displacements (less than 10 in) likely to be encountered underground. This report documents these tests and postulates some explanations of failure mechanics for the observed behavior.

Jan 1, 1988

By B. Olson, V. A. Marple, D. J. Radet

"Gravitational forces have been found to be an important factor in defining the particle collection efficiency curve of inertial impactors for large particles. In general it was found that if the parameter G = gW /V 0 2 (g is the gravitational acceleration. w is the nozzle diameter and V 0 is the average fluid velocity at the nozzle throat) in greater than 10-3 the efficiency curve would shift to lower panicle sizes. No effect could be seen for lower values of G.IN'IRODUCTIONInertial impactors have long been used as classifiers for airborne particles. By proper design of the nozzles and flow rate it is possible to classify particles with a fairly sharp cut in the particle size range from approximately .02 µm to 50 µm. Because of inertial impactors wide usage they have been extensively studied calibrated and evaluated. Most of these studies have been experimental calibrations of single stages using monodisperse aerosol particles. However, due to impactor simplicity. i.e. a jet of particle laden air impinging upon a flat plate with large inertia particles crossing the streamlines and impacting upon the plate the impactor also lends itself to theoretical evaluation.The most comprehensive method for analyzing impactors theoretically is to use finite difference solutions to the Navier-Stokcs equations and solve for the velocity components and pressure at node points of a grid placed over the area of interest. Using iteration and relaxation techniques the value of the velocity vectors can be determined at these node points with good accuracy. Once the velocities arc known, theoretical particles of known size can be placed into the now field and their trajectories determined by analyzing their equation of motion using numerical methods.Rader and Marple (1985) have performed theoretical analysis on impactors and have included such factors as Ultra-Stoksian .drag and the physical diameter of the particle in their analysis. However, even with these· factors included, there appears to be discrepancy · between the experimental and theoretical results when the particle size is larger than approximately 4 or 5 µm. One possible reason for this discrepancy could be the effect of gravity on the particle as it passes through the impactor. Therefore, a program was initiated to study the effects of gravitational forces on the collection· efficiency of particles in impactors. The results of that study arc presented here."

Jan 1, 1990

By W. H. Young

The thickness of the coal seam is one of the more important items influencing the productivity and general overall efficiency of operation 1 of a coal mine. The average thickness of coal seams mined in the United States decreased 2 inches between 1950 and 1955 to an average of 62 inches, which also is 3 inches less than the 65 inches in 1945. The decrease in thickness is due partly to the increased production from strip mines with thinner seams and partly to the increased percentage of total production at underground mines in certain States having thinner seams. The thickness of seams at auger mines was measured for the first time in 1955 and was 53 inches. Though bituminous coal and lignite is mined today from seams of exceedingly variable thickness -less than 2 feet to ore than 50 feet -a large majority of the production, 65 percent in 1955, came from seams 3 to 6 feet thick. This is not surprising since the coal seam of moderate thickness presents the least mining difficulties.

Jan 1, 1957

By Harold L. Rhodes

The Bureau of Mines has developed a quantitative method to determine water vapor in helium in the range of 0.1 to 15 ppm by volume. This method uses the quantitative chemical reaction of H20 with CaH2, which produces 1 mole of hydrogen for each mole of H20 in the sample. A gas chromatograph is then used to determine the concentration of hydrogen in the product. The precision of the H20 analysis is ±0.05 ppm at a concentration of 1 ppm. This method is used to calibrate a commercial platinum-phosphorus pentoxide (Pt-P205) electrolytic water vapor analyzer that has an improved inlet system and digital voltmeter readout.

Jan 1, 1981

By F. E. Block

This investigation was made as part of a larger program to develop basically new methods for preparing yttrium metal in high-purity form. It was performed under a cooperative agreement between the U.S. Atomic Energy Commission (AEC) and the Federal Bureau of Mines. Laboratory-scale tests were made to devise methods for preparing high-purity, anhydrous yttrium trichloride, for reducing the yttrium trichloride with sodium or lithium, and for consolidating the resulting yttrium sponge into ingots.

Jan 1, 1960

By B. E. Davis

Over 80 pct of domestic phosphate rock, which is the starting material for phosphorus-containing fertilizers, comes from central Florida deposits. As K-her grade deposits are depleted, lower grade phosphate ores containing 'Mg0 in the form of dolomite are encountered. Treating high MgO ores with present beneficiation technology will not yield a concentrate meeting specifications for acidulation. The Bureau of Mines conducted research on three high-MgO phosphate samples from south Florida. The sales contained, in percent, 5.4 to 10.2 P205, 1.9 to 7.6 MgO, and 35.3 to 60.1 acid insolubles. A technique of sizing, grinding, desliming, scrubbing, and redesliming was used to produce a feed suitable for continuous flotation studies, A conventional fatty acid-fuel oil rougher flotation followed by two to three cleaner stages resulted in concentrates containing, in percent, 30.7 to 31.3 P205, 0.6 to 1.3 MgO, and 2.5 to 4.8 acid insolubles. The P205 recovery from the flotation feed ranged from 55.1 to 89.7 pct.

Jan 1, 1984

By Leonard F. Heising

Domestic production of Metallurgical-grade manganese has contributed such a small percentage of the United States industrial demands that areas known to contain large tonnages of low-grade manganese ore have been investigated by the Bureau of Mines to reduce this country's dependence on foreign ores. A major source of low-grade manganese is the Cuyuna iron range in Minnesota. The entire Cuyuna iron range is covered by an overburden of glacial drift that, in some places, reaches depths of 200 feet or more. Prospecting and exploration must be guided by geophysical methods, drilling results, or projections of exposures found in operating mines because there are no outcrops near the productive parts of the range. Past drilling for the purpose of outlining iron ore generally was confined to the highly oxidized zones. Much of the manganese with which the Bureau of Mines is concerned occurs in thin-bedded unoxidized iron formations, too low in iron content to have been of interest to those seeking commercial iron ore. The primary objective of the core-drilling reported here was to obtain cores of different classes of manganiferous rocks and to determine whether or not the samples were amenable to beneficiation.

Jan 1, 1959

By L. C. IlsLey

"The maintenance of permissible equipment which is tested and inspected at the Pittsburgh Experiment Station of the United States Bureau of Mines is dependent to a surprisng degree upon the voltage at which the equipment is operated. The difficulty of maintaining 500-volt equipment is frequently brought to the bureau's attention, and it is quite possible that if the bureau had appreciated at the beginning the full hazard involved, it would never have undertaken the approval of equipment operating at voltages greater than 250 volts.In this connection, the following statement from State mine inspection departments and other sources are of interest as showing the general feeling in safety organizations with respect to voltages higher than 250. These statements, although obtained as a result of a questionnaire sent cut several years ago, still apply very well to present conditions.A. I have not had time to consider seriously the proposed change from every angle, but looking at it from a standpoint of hazard, feel that the danger would be greatly increased. I have always occupied the position that underground voltage on portable equipment should never exceed 250 volts.High voltage of course would mean smaller transmission lines, which would be more economical and no doubt would require in several instances smaller equipment; notwithstanding, if this statement is true, the writer is still favorable to low voltage on underground portable equipment.B. I believe 500 volts should be the limit on the best equipment ender the best conditions and that the U. S. Bureau of Mines should do all in its power to limit the voltage to 500 volts on permissible equipment, as any increase in voltage means increased hazard.C. I will refer you to a section of our mining law, entitled ""An Act to Regulate the Tine of Electricity in the Mines of the State of ----"" which reads in part, as follows: Trolley wires, or other exposed electrical wires, shall not carry a voltage above 275 volts.You may readily see by this that we are not permitted to operate mining machines under ground in -----, with more than 275 volts at the terminals, except that we are permitted to install transforming stations throughout the mines, after complying with certain regulations at the mine.However, as we have had to date, within the calendar year of 1925, six men electrocuted in the mines of the State, using a voltage of 275 volts, I am of the opinion that if this voltage was increased, the hazard would also be increased in proportion.D. I do not care to make a statement for publication: however, I am referring you to our mining laws. On page 27 and 28 you will find what the laws of -----¬require relative to the installation of electricity in the mines.""Hereafter where electricity is installed no higher than two hundred seventy-five (275) volts shall be used underground, except for transmission, or for application to transformers or other apparata, where the high-voltage circuit is stationary. High-voltage motors, and transformers, shall be installed in suitable chambers, built of fire-proof construction, and well ventilated, and shall not be placed on intake, or between intake and return air courses. All high-voltage lines lines and apparata must be clearly marked, to indicate their danger. Main and distribution switchboards for high voltage shall be made of insulating and incombustible material, such as marble or slate, and to be free of all metallic veins, or of material equivalent thereto. Same shall be installed in a dry place. All switches or other instruments used in connection with high voltage shall be installed on suitable switchboards, with at least a three-foot passageway in front and rear properly floored, and kept looked by a door at each end that can be opened from the inside without a key. With higher than medium voltage, there shall not be any live metal work on the front of switchboard, and the entry circuit must be protected by an oil breaker s"

Apr 1, 1932

By W. Ayvazoglou

A large number of organizations interested in the search for mineral deposits have adopted the magnetic method of geophysical prospecting, as it has proved to be the most simple, convenient, and rapid, and at the same time the least expensive in comparison with other methods. According to the last statistical data, about two millions square kilo¬ meters were explored in the United States by different geophysical methods. Ninety-six per cent of this area was prospected for oil and 4 per cent for minerals. Detailed exploration by means of the magnetometer has been carried out over about 85 per cent of this surface. The great advantages offered by this method resulted in the fact that the magnetometer was tried out in most places in which geophysical methods were applied. The main purpose of such e:rploration is to obtain the maximum knowledge valuable to the geologist; therefore good geological interpretation of the results of measurements is important. The possibility of drawing practical conclusions from a map representing the results of the study of the terrane depends greatly on the accuracy with which the measurements are made. The purpose of this article is to show the different sources of error by which the work of an operator may be affected and to discuss the means by which the carrying out of a magnetic survey may be improved.

Nov 1, 1931

By C. Ortuglio

The Bureau of Mines developed equations to determine the relationship of yields and products obtained from BM-AGA carbonization in 13-and l8-inch-diameter retorts. The developed equations indicate that results of carbonization in l8-inch-diameter retorts can be predicted from results obtained with l3-inch-diameter retorts.

Jan 1, 1966

By E. D. Gordner

Irrespira ble gutses issuing from the rock fofflb tions ere tJ source of expense ond danger in some metGLl mines. There is a great Variation in the compos i-· tion of such gdses and, os shown 'by recent sampling by the Bureau of ines, the gas rr;;,.y consi$t mostly ct carbon dioxide, (Rocle Strata Gtsses in the Mines of the East Tintic Mining District, by G. E. McElroy, Bu.retau of Mines Serial 2Z75) or f methone (Metruine in Ccalifornia C.old Mines, by B. 0. Picl-Q:lrd i:lnd !.. D. ("iordner, Bure, cf Mines Serial 2303), or nitrogen, sin the present instonce. A nl.liilber of unventilated rt:t.ises in some of the mine of l:l Neva&. district conuin «i'ccumulCltions of l;i hih-nitrogen gas the1t will not supi:ort life or combus­tion. The rdises ore in different geologiecil formations and in widely sep1:1rated. loecslities in the mining district. One ot" two ri::lises in the sme fc.rtr.ation may be full of the gos cand einother nec-r'by be t'ree ot· it. Lives have been lost t:lnd a number of men heave been overcome on enteing unvetilated rtsises in which their­respircable tss hcsd c1ccuni..1.l1::1ted between sldfts. Gener1:1lly, however, the gas see:ns to noozett from the .t'onrbtio:1 ond to ecc1: .. ,i.-1,;.1:.1te so slowly tMt its presence is not suspected t the tfr.1e, bu.t discovered. ed:'t&.c' the raise is t)band.oned. OcCE.isionelly 1 t issues from a ne•.,ly cut cre·tice or fissure under considerca ble pressure and in lar!?e enough '3.'16ntities to overcome or drive 011t men working in unventilated places.

Dec 1, 1922

By R. Van A. Mills

This preliminary paper is intended to answer briefly some of the inquiries coning to the Bureau of Mines regarding the so-called "paraffining", of oil wells and methods of preventing and remedying that trouble. The increased difficulties in operation and the losses of production caused by the deposition of gummy and waxy hydrocarbons, commonly called paraffin, in the wells, tubing, other pumping equipment, and in the pores of the productive sands, have long been recognized but the trouble has not been overcome. The nature and causes of the trouble, together with some of the possible methods by which it may be diminished or overcome, are outlined below. Character of the Peraffining Materials. The so-called paraffin that collects in oil wells end in the pores of the oil-producing sands immediately around the wells, is generally made up of amorphous wax or uncracked paraffin, asphalt, or other gummy hydrocarbons mixed with more or lees water, oil, and inorganic silt. Some of the samples of this "paraffin" collected from oil wells in different fields and examined by the Bureau of Mines contain as mach as 20 per cent by weight of water and inorganic silt, whereas other samples are composed entirely of waxy hydrocarbons and oil. The inorganic silt accompanying this "paraffin" is mostly fine sand, clayey materials, common salt and finely disseminated precipitates of calcium and magnesium carbonates. Sulphates of calcium, barium, and strontium are less common constituents of the "paraffin."

Jan 1, 1923

By J. E. Murphy

Purification of samarium metal by sublimation and by vaporization from a low-melting metal flux, at the same temperature, were compared. Vaporization proved more effective for removing impurities such as magnesium, calcium, and manganese. Recovery of samarium, however, is more rapid by sublimation because of its constant rate of distillation.

Jan 1, 1970

By W. L. Crentz

Knott County is one of the smaller coal-producing areas in the Eastern Kentucky coal field. It contains numerous coal beds, many too thin to support mining over a wide area, Coal produced in the county is from a few rail-shipping operations and many small truck mines. Many smaller mines are working beds whose exact location in the coal-bearing strata is uncertain. Samples were collected from 11 different coal beds, of which the Fire Clay, Hindman, Upper Elkhorn No. 3, and Flag are the most import ant from a product ion standpoint. Known reserves in the Hindman bed. are very limited, and almost the entire production from this bed is gathered from two comparatively, large rail-shipping mines in addition to the four principal beds, samples were taken in the Francis, Haddix, Fire Clay Rider, Whitesburg, Amburgy, Upper horn No. 2, and Upper Elkhorn No. I .beds. Figure 1 is a typical section of the strata, showing the more important coal beds and. readily identifying their location with respect to each other. The bed names as shown are particularly important because of the local tendency to assign several names to the same bed. To avoid confusion, the names by which each coal bed is known also are given in the following listing. The coal. beds., in descending order, follow: [ ]

Jan 1, 1953

By M. C. Malamphy

A general description of the activities and results of bauxite investigation by the Bureau of Mines at its bauxite project in Saline and Pulaski Counties, Ark., has been given in Report of Investigations 4251. In this volume and in a series of Reports of Investigations immediately following the factual data obtained during the project are reported. The data are accompanied by maps showing the location of holes drilled and the deposits developed. Each area upon which work was done is reported by half townships. Each bauxite deposit investigated was assigned a name and a number for ready reference and identification, and its location und name are shown on the appropriate half-township map.-The description of each half township is followed by a description of each deposit developed in that half township. The 14 half-township maps and 77 detail maps of the bauxite deposits in this eeri88 of reports give the locations and numbers of all the holes drilled on the project except the deep holes drilled to test the geophysical anomalies. The locations of those holes show on figure 13 in volume 1 (R. I. 4251). The descriptions of the deposits developed are followed by complete detailed logs of the drill holes. Many of the widely spaced exploratory holes did not discover bauxite of minable thickness and grade. The pertinent information obtained from the widely spaced exploratory drill holes has been summarized and tabulated, and a table tor each half township is given with the discussion covering that area.

Jan 1, 1948

By R. E. Campbell

Uranium metal of improved purity was prepared by electrorefining commercial magnesium-reduced uranium in a molten sodium chloride-uranium trichloride electrolyte. The best operating conditions for the preparation of refined metal were established as follows: an electrolyte containing 8.7 to 13.3 weight-percent uranium; initial cathode current densities from 300 to 1,500 amp/sq ft; and a molten salt temperature of 860° C. Ingots produced from electrorefined uranium crystals prepared with these operating conditions were substantially free of metallic impurities. The only impurities in the refined and consolidated metal were present in low or undetectable amounts.

Jan 1, 1965

By W. P. Yant, H. C. Fowler

"INTRODUCTIONHydrogen sulphide is probably the most toxic gas associated with crude oil. Hydrocarbon (petroleum) vapors themselves are harmful to the human system, but hydrogen sulphide, when present, is usually more important from the standpoint of health and safety. These conclusions were reached in an investigation of the toxic gases encountered in the transportation end refining of high-sulphur petroleum. The results of that investigation are presented in Bureau of Mines Bulletin 23l. although the writers of Bulletin 231 paid no direct attention to the production of oil in the field, they attributed to hydrogen sulphide reports of accidents caused by gas in the oil fields of Mexico.During the development of oil fields in Texas, a ""poison gas"" was encountered that constituted a decided health and safety hazard. The present report discusses an investigation of this gas made in July, 1926.The major portion of the investigation was conducted in the Panhandle field of Texas, but the study also includes the Big Lake and McCamey fields.Scope of WorkThe work undertaken in each field included:Examination of the gas-coming from representative wells at various locations in the field; also analyses of the gas-air mixtures to which the workmen were or might be exposed.Observation of symptoms of poisoning and severity of these symptoms."

Oct 1, 1926

By Deno M. Pappas, Christopher Mark, Eric R. Bauer

During 1998-99, groundfall incidents resulted in 27 fatalities and were responsible for over 70% of all deaths in U.S. underground coal mines. To obtain a better understanding of where and why these incidents occurred, a comprehensive analysis of ground fall injuries and fatalities was conducted. The first portion of the study examined various factors associated with roof and rib fall injuries and reportable roof fall noninjuries that occurred during 1995-98. The study found that the room-and-pillar mining method has twice the groundfall incident rate than the longwall method. Mine locations with high groundfall rates seem to correlate to regions where there is a higher concentration of problematic coalbeds. For example, the Illinois Basin has very high groundfall rates, which can be traced back to several key coalbeds-Kentucky No. 13, Herrin/No. 6/Kentucky No. 11, and Springfield No. 5/Kentucky No. 9. High rib fall rates were found in mines located in thick seams. Groundfall rates were found to be 30% to 40% higher during the months of July through September, possibly due to high humidity that may cause the shale mine roof to deteriorate. The second part of the study examined the root causes of failure by reviewing all groundfall fatality reports for 1996-99. Primary and secondary hazard factors were assigned to each groundfall incident. The primaryf actors resulting in these groundfall fatalities were pillar extraction, traveling under unsupported roof, skin failure, construction, longwall faces, intersections, and geologic discontinuities. Defining prominent ground control incident trends and hazards will identify areas where additional study is needed and where innovative solutions need to be developed to reduce these severe occupational hazards.

Jan 10, 2000

By Paul W. Jeran

This Bureau of Mines report has been prepared to provide a means whereby mineworkers without specific geologic training can recognize and record the existence of potentially hazardous geologic features encountered in coal mines. Each geologic feature described in this report has been implicated in roof failure. Through the recording of the observations of mineworkers, based on this report, a geologic map of mine workings and the associated ground control problems can be compiled. From such maps, the trends of changes and features can be determined and projected ahead of mining. The face crew can be alerted to a potential problem and what to look for as the face is advanced.

Jan 1, 1983

By M. R. Geer

The use of the cyclone as a dense-medium cleaning device was first described by Driessen6/ in 1945, after development of the process in the Netherlands during the German occupation of World War II. A pilot plant was built in the Netherlands soon thereafter, and the first commercial plant was built in 1948. By 1958, 18 plants were operating or under construction.7/ Thus, economic factors in Europe, where the high cost of coal places a premium on efficient cleaning, dictated rapid adoption of the cyclone. American reception of the process differed. The Bureau of Mines presented the results of its own small-scale cyclone experiments in 1946;8/ showing a sharp separation between coal and impurity; adoption by industry now is taking place. There is now much greater emphasis on the efficient cleaning of fine coal, and the first American cyclone plant has begun operating; others are planned or under construction. With the present interest in improved treatment of fine coal, the Bureau of Mines felt that additional performance data on the cyclone would be helpful to industry. Therefore, a complete, open-circuit pilot plant was built to make cleaning trials on American coals covering a wide range of washability characteristics. Five raw coals and one middling product were included in the investigation, and each was cleaned at several densities; 17 cleaning trials are reported.

Jan 1, 1961