Search Documents

By C. A. Rhoades

The spillage that accumulates under conveyor belt lines presents a possible fire and explosion hazard fomiinqjetsoruiel, especially to those who must clean up the spillage. The U.S. Bureau of Mines conducted research to reduce this hazard by identifying and investigating the parameters affecting the efficiency of conveyor belt cleaning. The amount of material carried back under the conveyor and the wear rates of metal cleaning blades decreased with increasing blade-to-belt pressure to a limiting value, after which the carryback and wear rates remained essentially constant. The optimum blade-to-belt pressure was found to be 11 to 14 psi for the research conveyor system. Greater pressures increased the blade-belt friction without improving either cleaning or blade life. The modes of blade wear were three-body abrasion and slurry erosion caused by the sand-lime test mixture. Wear rates were reduced by increasing the metal hardness, opti-mizing the pressure, and removing conveyor belt imperfections. Corrosion was not observed to affect the wear of various steels in tests of less than 34 h. The results of this study should allow mine operators to run their conveyors under conditions that will maximize cleaning and minimize equipment wear.

Jan 1, 1989

By J. J. Shields

This study by the Federal Bureau of Mines concerns different methods of face haulage used with various types of continuous-mining machines, mobile-loading machines, and track-mounted equipment under varying roof and bottom conditions and in coalbeds of varying thicknesses. This report is the ninth in a series on mechanical mining in bituminous coal mines. Reference to the reports previously published is made in appendix III, p. 106. Use of modern mining equipment in bituminous coal mines has resulted in increased productivity at the face. This especially is true where continuous-mining machines are used, and the supervision is good. Previous methods and equipment for moving coal from the face became inadequate and had to be improved to restore balance to the mining systems. Sometimes new equipment was needed to improve the face haulage, and in some instances, a new combination of existing equipment was used. Detailed studies of face haulage methods were made at 13 mines in Pennsylvania, West Virginia, Ohio, and Illinois to compare their effectiveness and to describe fully the conditions under which each method was used.

Jan 1, 1960

By R. L. Gall

This report describes Bureau of Mines experiments in gasifying coal in a helium-heated tube-coil reactor. The purpose of this work was to investigate helium as a medium for transferring heat from a nuclear reactor to gasify coal or for use as high-temperature process heat. A laboratory-scale system was designed and constructed to demonstrate feasibility. In preliminary tests with this system, in which the coal was fed as a water slurry, the helium-heating and recycling equipment operated well. Considerable difficulty was experienced, however, in preheating coal slurry to the desired range of 400° - 1,000° F. without plugging the preheaters. Five different preheaters plugged with coke or with salts leached from the coal. The longest operating period wan 12 hours. These difficulties were partly due to the relatively small equipment and flow rates. The gasifier processed l pound per hour of low-rank coal at 300 p.s.i.g. and 1,800° F., with the carbon conversion limited to 20 to 30 percent by the short residence time and slow heat-transfer rate.

Jan 1, 1962

By Rudolf E. Greuer

The existing computer programs for the simulation of ventilation systems under normal ventilation conditions are reviewed and a suitable program for including the influence of mine fires is selected. New program parts are written for the consideration of methane productions in coal mines, heat and gas productions of mine fires, temperature and air composition changes in ventilation systems, and the ventilation forces resulting from the latter. Other program parts are provided for the detection of danger zones and reversed air currents and for the inclusion of recirculated air currents in the network analysis. Existing program and new program parts are combined. The resulting new program can be used for a multitude of assignments. It is designed for the practical ventilation engineer and should be applicable to all types of ventilation emergency plans, in particular mine fire plans. The organization of the program and its mathematical basis are described. A FORTRAN IV listing and several flow diagrams are included. Eight executed examples are discussed, input and output for these examples explained. Storage requirements and execution times are estimated.

Jan 1, 2011

By Reynold Q. Shotts

A study was made of the coal resources of an area in Jackson County, Ala., forming a part of the Flat Rock, Henegar, and Stevenson quadrangles. The area studied is a portion of the Plateau coalfield on Sand Mountain and is near the Tennessee Valley Authority's Widows Creek steamplant. Since no detailed geological study of this area had been published, some reconnaissance work was done. The coalbeds and adjacent strata such as sandstones, conglomeratic sandstones, and conglomerates were studied. Available drill logs, together with the areal geology, provided sufficient information to permit correlation of the coalbeds and an estimation of coal reserves. For all categories of reserves, computed on a regional basis, a total of 72,920,000 tons of coal more than 14 inches thick is estimated for the areas studied in Stevenson. Flat Rock, and Henegar quadrangles. Of this tonnage, 40,001.000 tons is estimated to have less than 60 feet of overburden. The total measured coal reserves for the above three quadrangles are 16,359,000 tons, with 12,471,000 tons under less than 60 feet of cover.

Jan 1, 1966

By Stephen C. Tadolini, Yunqing Zhang, Thomas M. Barczak

Standing crib supports have been applied in underground mining programs to resist large roof movements and sustain high-loads. The strength and deformation capability of these systems has been documented under both laboratory and field conditions. The parameter that has not been examined and is not well understood is the effect that a crib or other types of standing support has on the primary and secondary bolting systems. A crib support system with low system stiffness may allow large amounts of closure and deformation and cause the bolting systems to yield or even fail. Conversely, cribs or standing support that are too stiff may experience brittle or buckling failures, negating the advantage of the intrinsic supports previously installed. Utilizing a combination of field measurements and 3-dimensional finite element modeling techniques, the relationship between system stiffness and the subsequent performance of the installed bolting system is evaluated. Additionally, a simple method for calculating the combined system stiffness for standing supports, when using materials with different strengths such as steel, concrete, wood, etc., is presented.

By John P. Capp

Information is summarized on the major uses of fly ash and prospects for utilization in agriculture and in brick and mineral-wool manufacture. Technological aspects of utilization are discussed and references are given to the work of many of the leaders in the fields of fly ash production, processing, and utilization.

Jan 1, 1970

By C. E. Rork

This paper discusses various mechanical improvements that have been gradually incorporated in the copper-willing plants of the Southwest daring the past 14 years, power plants for concentrators, use of large-size units of equipment, and the effect of plant capacities on costs. The improvements in mechanical equipment and plant design have contributed in the reduction of operating costs; in some instances a saving in the capital cost per ton of daily capacity milled has resulted.

Jan 1, 1935

By G. W. Jones

In a previous report,6 results were given that showed the amount of natural ventilation in a manhole having a capacity of 74.l cubic feet when the number of ventilation openings in the cover was varied. from no openings to a maximum of 48. The results showed that the ventilation (air changes per day) in the manhole was proportional to the area of the openings in the cover, and also that the number or area of the openings was the factor that chiefly affected the ventilation.

Jan 1, 1937

Explosives identification tagging refers to the addition to explosives, during manufacture, of coded microparticles that can survive detonation, be recovered and decoded, and allow the explosives to be identified and traced to the last legal possessor as a result of distribution records kept of the coded tagged explosives. This study seeks to prepare the way for National implementation of identification tagging of all dynamites and cap-sensitive slurries (also known as water gels) by resolving technical issues and by developing a plan for pilot testing of the program. It is presented in two volumes: Volume I, National Implementation Model, and Volume II, Pilot Test Plan.

Jan 1, 1977

In July 1982 the Committee on Underground Coal Mine Safety completed its study of safety in U.S. underground coal mines; the results of the study were published in the National Research Council report entitled Toward Safer Underground Coal Mines. One of the findings of this study was: THERE IS A STRONG CORRELATION BETWEEN MINE SIZE AND FATAL INJURIES. THE FATALITY RATE IN MINES WITH 50 OR FEWER EMPLOYEES IS NEARLY THREE TIMES THAT OF LARGE MINES (WITH OVER 250 EMPLOYEES), AND ABOUT TWICE THAT OF INTERMEDIATE-SIZED MINES (WITH 51-250 EMPLOYEES). Although the Committee explored possible reasons for the higher fatality rate in the smaller mines, it was not able to explain this phenomenon fully. Therefore the Bureau of mines requested that the Committee undertake a supplementary study of fatalities in small underground coal mines. The Committee met in the fall of 1982, discussed the problem, developed an approach to it, approved a program of statistical analyses, and authorized a panel of four committee members to explore the problem in greater depth. The panel, in turn, reviewed the results of the statistical analyses and met with the president of the National Independent Coal Operators Association and with several owners of small underground coal mines for a detailed discussion of the unique problems of small mines. Panel members examined 66 individual fatality reports prepared by Mine Safety and Health Administration (MSHA) inspectors who investigated fatal accidents that occurred in small underground coal mines in 1979 and 1980. This report is the result of those studies, analyses, and deliberations. The first draft was prepared by the panel, but the report has been reviewed and approved by the entire Committee.

Jan 1, 2011

By Charles W. Merrill

The U .S. Treasury stocks of silver have been reduced at such a rapid rate to meet industrial and coinage requirements that they face exhaustion in 3 or 4 years. Alleviation of the silver problem will require increasing supply or reducing demand. This paper examines possible long-range resource development and research programs and improved secondary recovery. The possible reduction or elimination of silver in coinage and development and introduction of substitutes in the arts and industry are also discussed.

Jan 1, 1965

By W. M. Deaton

The formation of gas hydrates in natural-gas pipe lines depends on temperature and pressure conditions in the lines as well as on the presence of condensed water. The operating pressure in a pipe line may be determined easily and usually is available from the records of operation, but the temperature seldom is known. In cooperation with the American Gas Association, the Bureau of Mines, in its investigation of gas hydrates, conducted a pipe-line-temperature survey and studied underground temperatures at depths at which pipe lines ordinarily are buried and the relationship of these temperatures to prevailing atmospheric conditions. A similar but mere limited study of this type was conducted by engineers of the Bureau of Mines a number of yours ago.4/ A summary of the earlier findings was included in a general report by the Bureau on the flew of natural gas through high-pressure transmission lines.5/ In the present study, data on temperature variations were obtained at several places widely separated geographically. This information should assist pipe-line engineers in designing and operating natural-gas pipe lines.

Jan 1, 1941

By Charles W. Merrill

The U.S. Treasury stocks of silver have been reduced at such a rapid rate to meet industrial and coinage requirements that they face exhaustion in 3 or 4 years. Alleviation of the silver problem will require increasing supply or reducing demand. This paper examines possible long-range resource development and research programs and improved secondary recovery. The possible reduction or elimination of silver in coinage and development and introduction of substitutes in the arts and industry are also discussed.

Jan 1, 1965

By Walter C. Woodmansee

The only reported mineral production in 1977 was small output of alluvial gold, valued at an estimated $54,320.2 In addition, marine shells are gathered for use in lime manufacture, although output was not reported. Proposed development of a bauxite mine and smelter, involving Rennell and Vaghena Islands, was deferred in June. Conzinc Riotinto of Australia Ltd. (CRA), in partnership with Mitsui Mining & Smelting Co. Ltd., and the Solomon Government, with- drew from the project, and Mitsui, which conducted a feasibility study and metallurgical testing of the bauxite, decided to defer further work because of slack demand for aluminum in Japan and difficulties in arranging financing. The Mitsui feasibility studies reportedly indicated that the project could be viable despite technical difficulties and relatively high initial investment costs. The project was to produce 1.5 million tons of bauxite and 600,000 tons of alumina per year from reserves totaling 60 million tans at 45% to 50% A1203.

Jan 1, 1981

By B. W. Madsen

To help maintain an adequate supply of minerals to meet national economic and strategic needs, the Bureau of Mines developed a mathematical model that describes acidic ferric sulfate leaching of copper from sulfide ores. The leaching model can aid in maximizing minerals and metals recovery from primary sources by giving operators and management a better understanding of the copper leaching process. This will aid in improving dump leaching operations. The model is based on a steady-state approximation of the continuity equation for diffusion of ferric ions in the rock pores and the intrinsic leaching kinetics of the various sulfide mineral particles. Ore characteristics included in the model were ore particle-size distribution, particle shape, grade, mineral content, mineral particle size, porosity, and tortuosity. The continuity equation was used with ferric ion concentration gradients and a fixed value for the diffusion coefficient. Except for effective diffusivity, each of these factors was either measured experimentally or estimated from theoretical considerations. The effective diffusivities were determined by fitting calculated leaching curves with experimental leaching data. Vertical variations in leach solution composition and temperature within a dump are not considered in this model. The model accurately predicted copper extractions for several large-scale tests during nearly 500 days of leaching.

Jan 1, 1981

By W. I. Nissen

This Bureau of Mines report presents the design for a commercial-sized flue gas desulfurization (FGD) demonstration plant that uses the citrate process. The goal of the Bureau's citrate process is to minimize the undesirable environmental impacts of industrial plants emitting SO2-bearing gas. The FGD plant is located at the George F. Weaton powerplant, Monaca, Pa. Construction was completed in April 1979 and will be followed by preliminary testing and a 1-year testing and evaluation program. Design capacity of the FGD plant is 156,000 scfm of 0.2-volume-percent-SO2 flue gas yielding about 16 tons of sulfur per day. The plant is intended to (1) clean fly ash, SO2, and Cl- from the gas while cooling the gas in a venturi scrubber, (2) absorb SO2 from the gas using 1,200 gpm of a countercurrent-flowing citric acid-sodium citrate-sodium thiosulfate solution, (3) react the absorbed SO2 in two 13,000-gal stirred closed vessels with added H2S, thus precipitating elemental sulfur and regenerating the citrate solution for recycle, and (4) recover the sulfur from the slurry by air flotation, followed by melting in a heat exchanger and separation from the occluded citrate solution in a sulfur decanter at 35 psi and 135° C.

Jan 1, 1979

By Herbert H. Einstein

Appendices A through M contain information that is the basis for many developments reported in the main text (Parts I through V); this information is, however, not needed in applying the research results. Specifically the appendices contain: A: Geology of Sampled Sites B: Comparison of Distribution Forms with Observed Trace Length Frequencies C: Joint Attitude Pole Diagrams D: Resistance and Deformability of Rock Discontinuities E: Resistance and Deformability of Joints - Details of Data Recording Procedure F: Documentation and Details for Simplified 2-Joint Wedge Analysis G: Generalization of the Stiffness Approach H: Inadequacy Due to Simplifying Assumptions in Wedge Analysis I: Rock Slope Reliability Analysis: State of the Art J: Resistance Derivations for Mechanical Model K: Supporting Derivations for Analysis Method DAYLITE L: Supporting Derivations for Simplified 2-Plane Reliability Analysis M: Plots of SLOPESIM Runs

Jan 1, 1979

As part of its research and development activities concerning coal mine operational/emergency communications sys terns, the Bureau of Mines commissioned several contractors to conduct electromagnetic (EM) noise studies and measurements that would aid the development of improved coal mine operational/emergency communications systems. The bulk of the noise studies and measurements were conducted in 1971. The Pittsburgh Mining and Safety Research Center (PMSRC) inherited the responsibility for monitoring the electromagnetic noise activities by mid-to-late 1971, and initiated a review and evaluation of the current and planned electromagnetic noise work. Arthur D. Little, Inc., (ADL) was asked by PMSRC to assist it in performing this review and evaluation by placing stronger emphasis on certain tasks of existing Contract No. H0122026. This technical memorandum report presents the findings, conclusions, and recommendations of our review and evaluation of the electromagnetic noise measurements of the five contractors we were asked to examine. Our review and evaluation effort included meetings and telephone discussions with technical staff of each contractor; serving as Technical Discussion Leader of a "Contractor's Round Table Meeting on EM Noise, Surface and Subsurface, Operating and Non-Operating Mines" called by the Bureau of Mines; examination and discussion of contractor reports and relevant open literature; sample verification calculations; and the documentation of our findings, conclusions, and recommendations by this report.

Jan 1, 1972

By C. Ogasawara

This document describes the direction and progress of the Bureau of Mines Oil Shale Mining Environmental Research Program as of January 31, 1979. It is aimed at focusing the Bureau's role in environmental research supporting oil shale development with respect to the activities of other involved government agencies and private industry. Environmental considerations in oil shale extraction, such as ecological disturbances, health and safety hazards, waste management, and socioeconomic impacts, are discussed along with the type of research known to be planned by organizations to ameliorate these problems.

Jan 1, 1979