Search Documents

By H. B. Humphrey, F. E. Cash

From 1900 to 1929 , 1,005 or approximately 30 per cent of all fatalities in the coal mines of Alabama were caused by fires or explosions of gas and dust . In the 3 -year period from 1927 to 1929 only 15 men were killed by these causes , a reduction from 30 to 9 per cent of the total . Notwithstanding this marked improvement , which is due largely to the efforts made by the State inspection department , the operators , and the Bureau of Mines to stamp out this type of disaster , Alabama still has more than its share of such fatalities which can and should be prevented. A list of explosions from 1894 to 1929 compiled from information obtained through the records of the State Inspector's office , the reports of Engineers of the Bureau of Mines , and the operators , is given in Table

Oct 1, 1930

By M. H. Chetrick

An important factor in the design and operation of a lignite-gasification plant is knowledge of the thermal requirements. These not only vary with different-size plants but also with the operating conditions for a plant of given capacity. Thermal data have been collected since 1945 from a commercial-scale lignite-gasification pilot plant operated by the Bureau of Mines at Grand Forks, N. Dak. The description and operation of this plant and a study of the gas-composition data have already been described in previous reports (1, 2, 3, 4, 5).2) / This investigation was made to review the thermal data taken in tests and to correlate them in terms of the fraction of undecomposed steam and the H2:CO ratio.

Jan 1, 1953

By R. M. Ray

The Bureau of Mines evaluated five commercial badge-type carbon monoxide dosimeters. Color changes in the badge reagent indicated the presence of carbon, monoxide. Possible effects of ambient conditions on dosimeter response to CO during or after coal mine fires or explosions were studied. Temperature and humidity changes did not change dosimeter sensitivity to CO. Contaminant gases such as CO2, N02, S02, and H2S had effects that varied with brands of dosimeters ranging from no effect to increased sensitivity to CO. Dosimeters tested after 6 months of storage showed an increase in failure rate as high as 25 percent. Tests were conducted to determine the effects on dosimeter time-for-color change caused by observer's sight (colorblind); lighting, and coal dust on dosimeters. No significant effects were observed. Observer variance was the most pronounced factor observed in all tests.

Jan 1, 1975

By Herbert R. Babitzke

The purpose of this investigation was to optimize the high-temperature properties of columbium and tantalum. Columbium and tantalum were combined with selected alloying elements to achieve solid solution and dispersion strengthening. Fifty-six alloys were evaluated to determine their formability, hardness, strength at elevated temperatures, and oxidation resistance. The following six alloys showed high-temperature strength: [Cb-15Hf-5W-2Zr-4Al-4Ti-2N Cb-15Hf -5W-5Zr Cb-15.3Ti-4.1Zr-13.7Hf Ta-20Hf-4Al Ta-30Hf-4Al Ta-20Hf-5W-4Al] At 1,200° C, the columbium alloys had strength values of 40,000 psi or greater, and the tantalum alloys had strength values from 50,000 to 58,000 psi. For a 2-hour test period at 1,000° C, weight gains of only 9 and 8 mg/cm2, respectively, were observed on oxidation testing of two alloys, Cb-15Hf-5W-2Zr-4Al-4Ti-2N and Ta-20Hf-5W-4Al.

Jan 1, 1968

By M. J. Brevoort

Research work in the Bureau of Mines cryogenic laboratory requires the use of high-sensitivity galvanometers of the d'Arsonval type in a building that is subject to unusually severe vibrations. A modified form of the galvanometer suspension described by Julius3 has damped the vibrations so successfully that a short note concerning it is thought to be desirable, The laboratory is on the site of the Amarillo helium plant near a building that houses gas engines of from 180 to 250 hp., driving compressors and electric generators. The distances from the galvanometers to the individual engines range from about 80 to 180 feet. The subsoil, consisting of black clay loam, transmits the impulses without much damping. The usual methods of protecting galvanometers from vibration were tried and proved fruitless. A Julius suspension purchased on the market was carefully installed in the hope that it would overcome the difficulty, but the conditions were too severe even for this elaborate arrangement. Several mudifications of the original Julius suspension, which were then introduced, resulted in almost complete elimination of all vibrational effects.

Jan 1, 1931

By Sabri Ergun, Robert W. Smith, Victor H. Tiensuu

Factual geometries are considered for X- ray scattering studies of weakly absorbing materials by both reflection and transmission methods . These studies are usually made on slab specimens to obtain adequate scattered intensities ; however , the intensities are appreciably influenced by absorption of the X-rays in passing through the specimens . Conventional equations derived to account for this absorption are based on idealized geometries , but for polycrystalline carbons the use of idealized geometries leads to several percent error in the corrections to be made . Use of factual geometries substantially reduces this error .

Jan 1, 1964

By Leroy Dockter

The grinding characteristics of lignite in a ball mill were investigated. The variables studied were initial lignite moisture content, degree of in-the-mill drying, and lignite source. The mill tested was a pilot-p1ant-size conical ball mill which had a maximum output of from 80 to 180 lb/hr pulverized product depending on the lignite and test conditions. The capacity of the test mill ranged from 82 to 103 lb/hr depending upon mine source, in pulverization of as-mined lignite with minimum drying, The capabilities of the ball mill could not be correlated to Hardgrove index of the individual lignites or other observed physical properties. Predrying lignite from its 35 to 40 percent raw moisture content to about 10 percent moisture before grinding improved the mill capacity 87 percent, compared to an increase in capacity of 74 percent with in-the-mi11 drying to the same product moisture.

Jan 1, 1967

By Charles L. Kimbell

For a study such as this, which summarizes and amalgamates much information collected, compiled, and utilized by the numerous U.S. Bureau of Mines country specialists and branch chiefs for inclusion in the country and regional reports that comprise the five other sections of 1991 Minerals Yearbook-International Review, it is clearly impossible to cite all sources of information used in its presentation, but some recognition is due. Generally speaking, this study and its related detailed studies on countries and areas would be much more difficult, if not impossible, without the efforts of the personnel of national mining and geological agencies throughout the world. Information that they collect, compile, and then publish, either in their own volumes or those of central statistical agencies in their countries, are the foundations on which this work rests. Thus, appreciation is expressed to the multitude of persons employed by these agencies.

Jan 1, 1993

By Miro Mihelich

The mines and prospects in the vicinity of Landlocked Bay, 25 miles southwest of Valdez, Alaska (fig. 1), were examined, mapped, and sampled in July and August 1955 as part of a comprehensive investigation by the Bureau of Mines of ore deposits adjacent to Prince William Sound. The purpose of the investigation is to establish and record the location, nature, extent, and metallurgical characteristics of copper and associated metallization in the Prince William Sound district and to indicate, if possible, those areas in which additional exploration and development may be justified. Of particular interest are the possibly numerous deposits of massive iron sulfides that were neglected during early mining operations. These deposits may constitute important reserves of sulfur and iron. At Landlocked Bay deposits of copper-bearing iron sulfide minerals have been mined or partly explored through mine workings, which are in a zone about 1 mile wide along the western side of a large overthrust fault known as the Landlock Overthrust. Eight of the principal mines along this zone were examined end sampled. Although only three of the mines have a recorded production of shipping-grade copper ore, all have deposits of copper-bearing iron sulfide minerals that are similar in occurrence. The deposits occur as lenticular masses and disseminations of chalcopyrite, pyrite, and pyrrhotite which replace crushed rock or fill cavities along shear zones in greenstones and in sedimentary rocks that are exposed between sea level and an altitude of 2,500 feet. These lenticular masses of sulfide minerals range in size from small pods to ore bodies that have been stoped to maximum widths of 9 feet, strike lengths up to 70 feet, and dip lengths as much as 350 feet. Where accessible for sampling,, the copper content of the deposits ranged from a few hundredths of a percent to over S percent; zinc, gold, and silver are present in negligible amounts. Flotation tests of a sample composited to represent typical mine-run ore indicate that 81 percent of the copper is recoverable in a product assaying 28 percent copper at a concentration ratio of 17.5 : 1. INTRODUCTION Statistical records indicate that approximately 110,000 tons of metallic copper (about 16 percent of total Alaskan production) was produced from mines adjacent to Prince William Sound during the 40-year period ended in 1938. Although the principal production was from a large-scale mining and milling operation on Latouche Island (Kennecott Copper Corp., Beatson mine), a substantial amount of the total copper was derived from direct-shipping ores selectively mined or hand-sorted from numerous other deposits in the district. No production has been made since 1938; many of the claims have long been abandoned, and mine workings are either caved or deteriorating rapidly.

Jan 1, 1957

By A. W. Fahrenwald

Coarse sand flotation, both alone and in conjunction with gravity concentration, is a subject of research at the U. S. Bureau of Mines Field Office, Moscow, Idaho. One of the most important results of this work which is being carried out in cooperation with the University of Idaho, has been the development of a concentration process embodying flotation, classification, and tabling, in the order named. The flow sheet of the process is given in Figure 1. The type of feed desired for this process is coarser than is common in present "all flotation" practice, and is about the size of table feed.

Jan 1, 1929

By Jack L. Henry

The Bureau of Mines conducted seven pioneering experiments in a 12-inch-diameter Kroll reduction reactor to examine the feasibility of coreducing the chlorides of Ti, AI, and V to produce a homogeneous titanium alloy sponge. The coreduction studies proceeded in a normal manner, and the yields of sponge were comparable with those of pure titanium sponge made in the same reactor. Vanadium concentration was very uniform throughout the sponge cake when VC14 in solution in TiCl4 was fed into the molten magnesium. More difficulty was encountered in feeding solid VCl2 and AIC13. Vanadium and aluminum concentration in the sponge was not uniform, and mechanical difficulties were experienced with the small-scale screw feeder. Although the sponge varied in composition from region to region, the ingots prepared from it were uniform in composition.

Jan 1, 1974

By Norman A. Pace

This paper is one of a series being published by the Federal Bureau of Mines on methods and practices used in mining and preparing crushed stone for market. Performance, in terms of units of work or tons produced per machine and per operator man-hour, is given whenever that information can be obtained. Direct operating costs are useful for comparing different methods and are included, if available. In addition to describing equipment and methods used} the Bureau considered it desirable to discuss the engineering reasons for the choices that have been made. This paper is particularly concerned with operation of the Camak quarry and plant of the Weston-Brooker Co. The quarry and plant are near Cedar Rock, north of State Highway No. 80 and east of Middle Creek in Warren County, Ga., and about 40 miles west of Augusta. Rail access is by a spur line of the Georgia Railroad from Camak, 5 miles southwest. The main office of the company is at Cayce, S. C.

Jan 1, 1959

By S. H. Lorain

This paper is one of a series on mining methods and costs being published by the U. S. Bureau of Mines. The operations of the Quartz Hill Mining Co., near Dewey, Mont., afford an interesting example of the cost of mining small bodies of direct shipping ore; they also illustrate the effect of the unavoidable periods of unusually high exploration and development costs in this type of mining upon the cost per ton of producing ore. The importance of skilled geological guidance and the necessity of avoiding unnecessary overhead and capital expense at small mines are shown. Operating conditions at Quartz Hill are typical of those in many other mining districts of southwestern Montana. It is believed that the costs presented here may be of value in the preliminary estimation of costs to be expected by conservative operators under similar conditions elsewhere. The information contained in this paper was obtained during a visit to the Quartz Hill mine in August 1936.

Jan 1, 1937

By L. P. Kleinmann

To control the formation of acid drainage at its source, the Bureau of Mines has investigated the role of iron-oxidizing bacteria in the oxidation of pyrite. In laboratory tests, it was determined that Thio-bacillus ferrooxidans could be controlled in coal refuse using anionic surfactants, with an associated decrease in acid production of about 75 pet. Based on these results, large-scale tests were conducted at an 8-acre active coal refuse area in northern West Virginia and an 11-acre inactive refuse pile in southern West Virginia. Acid production was decreased 60 to 95 pet for 4 to 5 months after application of 55 gal/ acre of 30-pct sodium lauryl sulfate solution. To date, effluent surfactant concentrations have been extremely low. Either a hydroseeder or a road-watering truck can be used to apply the surfactant. Since the surfactant solution must reach the pyritic material to be effective, sites that have been reclaimed are generally not amenable to these procedures. A simple laboratory test is described that provides an estimate of adsorption potential; this can be used to calculate a safe application rate.

Jan 1, 1983

By Franklin D. Cooper

Three model dwelling units were redesigned to achieve specific levels of noise reduction above that provided by conventional construction. Using 1968 prices, the added costs of materials and installation were found to range from $500 to $5,000 depending upon the size of the dwelling unit and the degree of insulation. The potential aggregate expenditures for sound insulation materials are projected to reach $617 million in 1975, including about $408 mil- lion for the mineral-based materials, in 1968 constant dollars. The report includes a brief review of the mechanics and effects of sound.

Jan 1, 1970

By John G. Kovac

A computer simulation has been developed to estimate the chances of a miner making a successful escape while wearing a SCSR. The model takes into account: (1) training in the use of SCSRs, (2) apparatus integrity, and (3) the oxygen cost of a mine escape. This Bureau of Mines report examines survival odds for a prototypical escape, and illustrates how these odds change when SCSR training is improved.

Jan 1, 2009

By George T. Motock

In Germany the extraction of lithium and its salts has been handled mainly by units of the two major concerns - Metallgesellschaft A, G. and Deutsche Gold und Silber Scheide Anstalt, both with headquarters in Frankfurt. Zinnwaldite, which belongs to the mica group, is the major source of the lithium-containing raw material in Germany. Lepidolite and amblygonite also are used when available, but they are imported, as there are no major deposits of these two minerals in Germany.

Jan 1, 1946

By Robert Roby

The Mouat copper-nickel deposit in Stillwater County, south-central Montana, was examined by Paul T. Allsman, an engineer of the Bureau of Mines, in 1939. Because of the strategic importance of nickel, a project was executed by John East, Jr., J. J. Naughton, and E. W. Newman, engineers of the Bureau, to further delimit some of the copper-nickel sulfide-bearing bodies that had been discovered by the Anaconda Copper Mining. Co. in 1937 and to investigate the central part of the deposit, which had not been drilled previously. This report is based largely upon the results of the. Bureau of Mines investigation and the results of exploration by the Anaconda Copper Mining Co. In addition, a brief description is given of some other copper-nickel sulfide-bearing deposits along tho Stillwater Complex.

Jan 1, 1949

By Richard A. Walker

This report describes the development and performance of a multi-level, multi-function Calibration Light Source designed for field-calibration of a group of specific photometers. The Calibration Source is capable of providing ±35% accuracy calibrations at all of the following levels: 0. 05 foot-Lamberts, 6 foot-Lamberts, 6 foot-candles and 20 foot-candles. The Source was found to provide constant light output to within 1% over 50 hours of lamp operation and for line voltage variations of ±25%. It is compact and light-weight (11 pounds), and can be easily transported and used by one man in normal office environments (without requiring a darkroom).

Jan 1, 1976

By H. R. Shell, Robert C. Johnson, Wilbur H. Warwick

Alpha silicon nitride fibers , Si3N4 , were successfully grown in graphite crucibles by a new method utilizing silicates and silicon ( S in equations below) as sources of silicon and using carbon , aluminum , and silicon as reducing agents (R in equations below ) . The basic reaction mechanism is believed to be generally as follows : 1,300 - 1,500 ° C S + R + N₂ SiO + RO + N₂ › 3Si0 + R + 2N₂ _1,300 - 1,500° C 3RO + Si¸N • ( 1 ) ( 2 ) A build - up of coatings on the solid raw- material particles hindered the evolution of silicon or silicon monoxide vapor and thereby slowed down further formation of silicon nitride fibers . Free oxygen in the crucible caused the formation of amorphous silicon dioxide ( SiO2 ) fibers . This problem was solved by passing , entering , and exiting gases through layers of lump graphite inside the reaction vessel . The silicon nitride fibers grew best around 1,400 ° C. Nitrogen flow rates from 4 to 6 liters per minute were adequate . The fiber widths were generally only a few microns whereas their lengths sometimes reached one - quarter inch or more . Chemical and X- ray analyses indicated that bulk fiber samples were usually 80 to 90 percent Si3N4 . The fibers had good oxidation resistance to about 1,260 ° C. Thermal shock resistance was excellent . Electrical resistance was determined .

Jan 1, 1964