Search Documents

By W. S. Landers

This report presents a detailed study of low temperature, entrained-bed carbonization of an Australian coking coal. The coal studied was high-volatile B bituminous from the Foybrook mine, an open-cut operation in the Liddell seam, New South Wales, Australia. Carbonization was conducted in an 8-inch diameter, continuous vertical reactor at several temperatures from 960° to 1,300° F. It was demonstrated that this bituminous coal can be carbonized within this temperature range to produce tar and a nonagglomerated char, without prior oxidation or char recirculation. Carbonization rates from 138 to 287 lb/hr (as-carbonized basis) were investigated. It was found that the carbonization temperature and the air-to-coal ratio must exceed minimum values to insure continuous operation. At the higher air-to-coal ratios employed, all or most of the carbonization heat was provided by internal combustion with air in the reactor. At the lower air-to-coa1 ratios, part of the heat for carbonization was supplied externally. On the moisture-and ash-free basis, the yield of tar plus light oil ranged from about 26 to 44 gallons per ton, and the char yield ranged from approximately 1,160 to 1,370 pounds per ton. The heat in the gas ranged from about 900 to 3,000 Btu/lb of moisture-and ash-free coal. Carbonization product yields correlated well with air-to-coal ratio and carbonization temperatures. The volatile matter in the char was found to be temperature dependent. At 1,300° F carbonization, the volatile matter in the char was 8.7 percent (dry basis), whereas at 9600 F carbonization, the residual volatile matter was about 16 to 18 percent (dry basis).

Jan 1, 1965

By Graham W. Marks

This report is the fourth of a series concerning the development of spectrochemical methods for the analysis of ore samples and related Metallurgical materials by the total-energy method. In this report, the application of this method to the determination of thallium is discussed. This element lies in group III of the periodic tale; one other Clement of this group; indium, has already been investigated.

Jan 1, 1949

By J. E. Pahlman

As part of its effort to reduce the need for strategic minerals through conservation and to reduce the capital and energy requirements of mineral processing, the Bureau of Mines has investigated a method for preparing ferrochromium alloys containing less than 2 percent carbon. This method will conserve chromium and should reduce the capital and energy requirements for chromite reduction. Reduced products containing less than 2 wt-pct C and as low as 0.01 wt-pct C were obtained by reacting pellets of chromite and carbonaceous reductant mixtures at pressures of 0.1 to 1 torr and temperatures of 1,230° to 1,320° C. The extent of reduction increased with increased temperature and decreased pressure; however, operating conditions were limited due to the onset of significant chromium vaporization at higher temperatures and lower pressures. Foundry coke, anthracite, and carbon black were found to be supe¬rior to graphite as reductants. The reduction of chromite to metallics was found to proceed via the carbide intermediates (Fe,Cr)7C3 and (Fe,Cr)23C6, No evidence of carbide intermediates Fe3C or Cr3C2 was found. Buttons of ferrochrome alloys were made by melting a mixture of reduced products with CaO and Si02 at 1,700° C for 20 minutes in an induction furnace,

Jan 1, 1980

By R. E. Perry

To develop new or improved flotation methods for beneficiating low-grade red iron ores, the Bureau made many bench scale and continuous anionic flotation tests on ferruginous sandstones and calcareous iron ores from the north-eastern part of the Birmingham, Ala., iron district. The ores contained about 21 to 36 percent iron, a to 11 percent lime, and 22 to 64 percent silica. Production of iron concentrates containing 48 to 52 percent iron was technically feasible in batch tests, and the iron recoveries ranged from 85 to 92 percent. In continuous tests 49 to 51 percent iron products were obtained with 80 to 90 percent recovery.

Jan 1, 1962

By D. Harrington

More or less unconsciously and from sheer force of habit human beings do many things they probably would not do if the possible consequences of their acts were fully recognized and appreciated. Such carelessness ordinarily could be condoned if human life were not at stake, but it is difficult to understand why intelligent men engaged in the hazardous occupation of mining indulge with the utmost indifference in some habit or continue some custom in violation of State leas and company regulations and under circumstances that may jeopardize not only their own lives but those of scores, even of hundreds, of their fellow workers as well. The old adage that stolen sweets are the best may or nay not have some foundation, but when applied to the practice of smoking surreptitiously in a coal mine, more especially a gassy mine, it is without even remote justification. Although a relatively harmless habit in the proper environment, smoking has been the cause or suspected cause of many gas explosions and black-powder ignitions and has resulted in numerous instances of bodily injury, loss of life, and destruction of property. Likewise, many fires in both coal and metal nines, causing loss of life, have been started by smoking.

Jan 1, 1941

By R. T. Johansen

A gradual decrease in injection rates commonly occurs as a water-flooding project becomes older. This decrease can be attributed to changes in reservoir conditions, such as swelling of clay minerals, fillup, or gradual plugging of the sand face. However, a rapid decrease in the rate of injection indicates abnormal behavior and is cause for alarm. Extreme plugging conditions can completely stop injections into a formation. Such behavior in wells was the main concern of the tests described in this report. An accepted method of alleviating this condition is by backflowing input wells - closing the supply lines to the wells and allowing the reservoir pressure to force water back into the wellbore and to the surface. If backflowing is not successful, a string of smaller diameter pipe sometimes is run inside the casing, and the sand face is flushed with a waterspray. More drastic treatment is to inject acid into the wellbore to dissolve extraneous matter, or even part of the reservoir material, in an attempt to restore the permeability of the sand immediately around the wellbore. Any of these procedures can he coordinated with bailing and swabbing of the well for cleanout purposes.

Jan 1, 1957

By L. Cheng

This report describes a laboratory investigation of the effectiveness of low-pressure steam and a steam-water spray sequence for the collection of airborne respirable (<10 µm) coal dust. Comparison of present results to previous results obtained with water spray alone indicates that the use of steam in a steam-spray sequence increases the collection efficiency by about 14 percent over that obtained by water spray alone. However, the use of steam to collect airborne dust requires cooling the steam-dust mixture in order to achieve condensation of the steam, and steam does not appear to be an attractive approach for collecting airborne dust in underground coal mining operations.

Jan 1, 1974

By Joseph E. Matta

The Bureau of Mines conducted a field study to investigate thin suppression of respirable dust by water sprays on a continuous-mining machine. Determining the importance of the top and bottom sprays for two types of spray nozzles was emphasized. Results showed, at a 90-pct confidence level, that (1) at least 70 pct of the dust was generated during the sump cut, even though nearly half of the coal was mined during the downshear operation, (2) the water sprays on the top of the boom had little effect in suppressing respirable dust, and (3) B.D. 5 spray nozzles mounted beneath the boom reduced dust at least 33 pet more than B.D. 5 sprays mounted on top of the boom. A single-cut technique was developed that gave good reproducibility for replicate cuts (coefficient of variation of 20 pct).

Jan 1, 1976

By Masami Hayashi

Cost evaluations were made for five processes for producing 100,000 tons of electrorefined copper per year from a chalcopyrite concentrate. The processes were (1) conventional smelting with all furnace gases vented to the atmosphere; (2) conventional smelting with converter gases routed to an acid plant and reverberatory gases vented to the atmosphere; (3) conventional smelting with converter gases routed to an acid plant and reverberatory gases to a citrate system plant; (4) conventional smelting with all furnace gases routed to a citrate system plant; and (5) a modified smelting process in which the concentrate is roasted before being charged to the reverberatory furnace, with roaster and converter gases routed to an acid plant. The total fixed capital costs of the plants were estimated as (1) $56.7 million, (2) $77.4 million, (3) $87.2 million, (4) $73.9 million, and (5) $77.0 million, respectively. Total S02 removal from stack gases as sulfuric acid or sulfur for each process was (1) none, (2) 66 percent, (3) 99 percent, (4) 98 percent, and (5) 78 percent. Assuming no credit for byproduct sulfur or sulfuric acid, total operating costs per pound of electro-refined copper produced were estimated as (1) $0.081, (2) $0.103, (3) $0.119, (4) $0.111, and (5) $0.103, respectively.

Jan 1, 1974

By Maria I. De Rosa

The Bureau of Mines performed experiments to determine concentrations of toxic gases and liquids, and smoke-particle diameters and diameter-concentrations evolved during degradation of PVC-derived brattice with and without nylon-woven fabrics, fiberglass, cotton, and jute brattices, and other mine materials. The samples were exposed in a 20-L chamber at temperatures of 1500 to 4500 C, with a chamber airflow of 10 L/min; 27.3 cm3/s of which was directed into a submicrometer-particle detector-analyzer. During the degradation of PVC-derived brattice, large concentrations of hydrogen chloride (TLV, 5 ppm; STEL, 100 ppm) evolved at a temperature as low as 2000 C. The minimum toxic load of 3.1 mg or 40 ppm in 50 L of dilution air, with O.l~g weight loss, may be reached at a mine face with 314,000 L of dilution air, at the 5th min, during which less than 1 kg of brattice undergoes combustion. Fiberglass, cotton, and jute brattices, pine wood dust, and coal dust showed small concentrations of carbon monoxide evolving during early stages of combustion. Hydrogen cyanide gas evolved from the PVC-derived, nylon-reinforced brattice; at a later stage of combustion, large concentrations pf carbon monoxide and dense smoke evolved from all PVC-derived brattices. Experiments to characterize smoke particles showed that marked differences exist in particle diameter-concentrations among the materials.

Jan 1, 1986

By Thomas J. Peters

During the 1982 Bureau of Mines study, 55 lode and 17 placer claims were held in the RARE II area. An estimated 150 lode claims and 50 placer claim, have been located in the study area; five were patented. There are no mineral leases. Gold has been produced from 8 lode mines and stream gravels have been worked for placer gold at 4 sites. Two suction dredges were active in stream gravels, but no significant gravel bars are identified. Identified mineral resources in the Weaver Bally area are gold and byproduct silver. The identified resources are at the Globe Mine, where approximately 33,000 tons of indicated marginal reserves (2,000 tons in the RARE II area, and 31,000 tons in the adjacent proposed Trinity Alps Wilderness) contain 0.45 oz gold per ton and probably 0.1 oz silver per ton. There are an additional 150,000 tons of inferred marginal reserves (35,000 tons in the RARE II area, and 115,000 tons in the adjacent proposed wilderness) averaging 0.38 oz gold per ton and probably 0.1 oz silver per ton. There is high potential for additional resources at the Globe Mine.

Jan 1, 1983

By Ned H. Snyder

In recent years the Government and other large consumers of coal have appreciated more and more the desirability of definitely determining by chemical analysis and test the character and quality of the coal they purchase. Higher prices for coal point forcibly to the need of giving more study to engine room and boiler room efficiencies and economies; this implies an intimate knowledge of the character and quality of the fuel used. Analyses and tests of delivered coal furnish data whereby power plant results can be comprehensively studied and a continuous check maintained on the coal and on the conditions of plant operation. Under authority of acts of Congress making appropriations for technologic investigation of fuels and the analyzing and testing of fuels belonging to or for the use of the United States Government, a laboratory is maintained at the Pittsburgh station of the Bureau of Mines, where samples representing deliveries of coal purchased for Government use are analyzed and tested. The Bureau of Mines has been active in promoting the purchase of coal by the Government under specifications/ that is, by contracts that make definite requirements regarding the heating value of the coal, expressed in British thermal units, and the composition as shown by proximate analysis. Under many of these specification contracts the bidders guarantee the quality of the coal offered, and that guaranteed by the successful bidder becomes the standard of his contract. The deliveries are sampled and analyzed to determine whether the coal is of the quality guaranteed by the contractor, and if it is not, the price to be paid is decreased in proportion; but if the coal is of higher quality, the price is proportionately increased. The known analyses of coals or the guaranteed analyses offered by the bidders may sometimes be used for determining the award of a contract, but if the coals offered differ widely in characteristics, it may be difficult to determine which would prove the cheapest fuel without data on their relative evaporative efficiencies. Hence, the making of evaporative tests under service conditions may be necessary in order to determine which coal is particularly adapted for successful and economical use in a certain plant. Once a particular coal is selected, however, regardless of the procedure of determining the award of a contract, then the greatest advantage of the specification method is realized, for it guarantees the purchaser receiving coal of uniform character and quality, thereby insuring the best results in the plant. The success of the specification method for the purchase of coal and the reliability of analysis now rests largely on sampling.3 Improper sampling leads to controversies, with resulting condemnation of the specification method in general and of the value of laboratory analyses and tests in particular.

Jan 1, 1922

By Fun-Den Wang

This report presents the results of two large scale field coal pillar strength tests (80 ft by 80 ft), the results of a series of laboratory small core sample tests, and the correlation between those field and laboratory tests. The concept of applying laboratory coal sample strength data to predict the in situ coal pillar strength appears to be feasible. The deformation property of large pillars can be obtained successfully by testing the coal sample in the laboratory within acceptable accuracy. There are prevailing directional strength and deformation properties in coal pillars along the butt and face cleat system.

Jan 1, 1976

By Paul W. Johnson, Ralph C. Kirby, Frank A. Peters

A series of economic evaluations of processes for producing metallurgicalgrade alumina from low- grade aluminous materials is being conducted by the Bureau of Mines to determine the relative processing costs . The two processes considered in this evaluation are concerned with the recovery of alumina from clay through the formation of ammonium alum . In the first process , dehydrated clay is leached with ammonium bisulfate solution ; in the second process , clay is baked with ammonium sulfate and then leached with water containing a small quantity of sulfuric acid . After the alumina is dissolved by either of these methods , the iron is reduced to the ferrous state to avoid crystallization of ferric sulfate with the alum . The recovery of pure alum requires two crystallization steps . The alum crystals are then redissolved and precipitated with ammonia to produce alumina hydrate , which is calcined to a - alumina . These evaluations are based on published work , and the proposed plants are designed for a capacity of 1,000 tons of alumina per day . The estimated operating cost per ton of alumina for the bisulfate leaching process is $ 117.06 , and for the sulfate baking process , $ 109.26 . Using a Marshall and Stevens chemical equipment index basis of 240.0 , the estimated fixed capital costs , in the same order , are $ 158 million and $ 146 million . Under current economic conditions , these two processes are not competitive with the Bayer process for the production of alumina from bauxite . Since small improvements will not reduce costs sufficiently to approach competitive costs , future research work with these processes should be confined to areas likely to result in major cost reductions .

Jan 1, 1965

By R. R. Schehl

The Bureau of Mines analyzed the structure of a high-grade metallurgical coke, carbonized at different temperatures in the range 500° to 1,000° C, through X-ray diffraction studies. Growth in the crystallite size with increasing coking temperature was calculated from profile analysis and compared with values obtained from the radial distribution function. The carbonization temperature appeared to have little influence upon the stack height, whereas the layer diameters more than doubled in size between 500° and 1,000° C. These results are comparable to those obtained from other studies of poorer quality cokes.

Jan 1, 1974

By Russell R. Trengove

In order to extend or delimit the known ore reserves adjacent to the Comet Coalition property on the western slope of the Highland Peak Range about 8 airline miles west of Pioche, Nev., the Bureau of Mines undertook an exploration project of diamond drilling. Production figures from this property, formerly known as the Schodde, are not available, but it has been reported that small amounts of rich silver and gold ore were Shipped by wagon to a smelter in the Salt Lake valley during 1900-1910. Small shipments were reported for the period 1915-1927, also. A study of the Pioche District by the Federal Geological Survey in 1942 and 1943 was the basis for the exploration program of the Bureau of Mines in 1947 This program consisted of diamond-drilling three holes. The total footage was 2,967 feet. No. 1 hole was drilled 1,260 feet, a record depth for diamond drilling in the Pioche District. Silver-bearing lead-zinc sulfide ores are found in the Combined Metals limestone, known locally as the C.M. bed, These deposits have been formed by replacement of the limestone that is inclosed in the Pioche shale.

Jan 1, 1949

By G. B. Gait

This report is the fourth in a series concerning the Bureau of Mines program for microfilming maps of abandoned mines in the Pennsylvania anthracite region; a catalog of the microfilmed maps of 70 mines in the Western Middle field is presented. Previous reports were catalogs of microfilmed maps of mines in the Eastern Middle field and in the Wyoming and Lackawanna Basins of the Northern anthracite field. Additional catalogs will be published as the microfilming of significant mining areas is completed.

Jan 1, 1971

By Leon E. Esparza

In 1985, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied the 16,927-acre Pryor Mountain Wilderness Study Area (MT-067-206), part of the 3,955-acre Burnt Timber Canyon Wilderness Study Area (MT-067-205), and part of the 4,550-acre Big Horn Tack-On Wilderness Study Area (MT-067-207) to evaluate their identified mineral resources. The Burnt Timber and Big Horn Tack-On study areas contain 3,430 and 2,550 acres, respectively. The three areas are in Carbon County, MT, and Big Horn County, WY, about 13 miles north of Lovell, WY. No identified resources exist in any of the study areas. Bureau of Mines personnel reviewed literature, searched county mining records and examined prospects, claims, and mineralized areas to determine whether identified mineral resources existed. The three study areas are within the Pryor Mountain unorganized mining district. U.S. Department of Energy production records indicate there were 223,000 pounds of uranium oxide (U308) and 236,000 pounds of vanadium pentoxide (V205) produced from 19 properties within the mining district. The average ore grade was 0.36 percent [3,600 ppm (parts per million)] U308 and 0.416 percent (4,160 ppm) V20S. Only the Pryor Mountain study area has current claims, the 50 claims of the S0S group.

Jan 1, 1986

By R. C. Anderberg, F. J. Caervenyak, F. J. Frattali, H. J. Kandiner, R. A. Brown

"INTRODUCTION Considerable interest was shown .prior to and during World War II in the winning of metallurgical-grade alumina from anorthosite, kaolin, siliceous bauxites, diasporic clays, and other aluminum-bearing ores. Laboratory and pilot-plant investigations were made on many of these ores by the Bureau of Mines, and a series of reports on them is being prepared. This report covers the tests made on the application of the lime-soda-sinter process to anorthosite, which is a mixture of albite, NaAlS1308, and anorthite, CaAl2Si208. Extensive deposits of anorthosite occur in the Laramie Range in Wyoming and extend into Colorado; other deposits are found in New York, with outcroppings appearing in Vermont, Maine, and Labrador.Anorthosito can not be treated by the Bayer process for the production of metallurgical-grade alumina, because excessive losses of soda and alumina occur from the formation of sodium-aluminum silicate due to the large amount (50 percent) of silica in the ore.RESULTS OF INVESTIGATIONSSmall-scale laboratory tests supplemented by pilot-plant runs have demonstrated that the alunina and soda occurring in the Wyoming anorthosite from the Laramie Range can be extracted and recovered satisfactorily by the lime-soda process. It has been shown that liquors containing approximately 95 gram of A1203 per liter can be consistently produced at Na20:A1203 ratios from 1.75 to 2.27, and that these liquors can readily be desilicated and carbonated to yield high-grade alumina trihydrate of quality comparable to that essential for cell-grade alumina. The optimum results were obtained with Na20:A1203 mol ratio of 1.03 and Ca0:Si02 ratio of 2.14 in the sinter when calcined at an average temperature of 2,444ºF. for 25 minutes."

Nov 1, 1947

By Bruce D. Sartwell

A program was written which utilizes a remote teletype input to a time- sharing computer to plot charged particle or X-ray energy spectra which are stored in the memory of multichannel analyzers. The program, written in FORTRAN V, accepts the data printed out by the pulse height analyzer on paper tape and then, after reading these data tapes into the computer, plots on the teletype the desired energy spectra on a scale automatically adjusted for the maximum number occurring in the data. The program is flexible enough so that the researcher can subsequently expand or contract the vertical (intensity) or horizontal (energy) scales. With a slight modification, the program will accept data printouts from scalers or analog to digital converters. The program also includes a feature for integrating the energy peaks obtained by pulse height analysis.

Jan 1, 1970