Search Documents

By E. C. Perkins, R. S. Lang, D. M. Taylor, H. Dolezal

The amenability of titaniferous slags and domestic mineral concentrates to chlorination was determined in a 6 - inch diameter fluidized bed chlorinator . Ilmenites from Valley County , Idaho ; Aiken , S.C ,; Trail Ridge , Fla .; and MacIntyre , N.Y .; and a titaniferous magnetite from Iron Mountain , Wyo . , were used in preparing the slags . The domestic minerals tested were an ilmenite concentrate from Valley County , Idaho , and a rutile concentrate from Magnet Cove , Ark . A high - grade Australian rutile was used as a standard for comparison . The impurity content of the slags and minerals tested , which was the most critical factor affecting their performance , was dependent on the geographical source of the material . All of the materials tested were amenable to chlorination in a fluidized bed although some required special operating conditions . Titanium extractions and chlorine utilization were over 90 percent for most of the slags and the Australian rutile . The Valley County , Idaho , ilmenite performed well in the reactor despite its 34 percent iron content .

Jan 1, 1963

By William D. Mayercheck

The U.S. Bureau of Mines is conducting research aimed at providing technology for a low-cost, high-recovery, environmentally acceptable mining system to recover the vast thin-seam coal reserves existing in the mountainous areas of the Appalachian region in the Eastern United States. As part of this research, the Bureau is evaluating new techniques to address these coal resources. This report summarizes the results of a worldwide technical search on thin-seam coal mining, the formulation of various methodologies for mining mountaintop thin seams, and the implementation and status of a physical model test program to validate and further develop the most promising concept-the "roof-fall-tolerant" mining system.

Jan 1, 1990

By Hewitt Wilson

A review is given of the nomenclature, sources, imports, statistics, common methods of preparation, and testing of mineral pigments. A description of the Deer Park-Spokane colored-clay district and the laboratory methods of preparation of these colored clays, others, and siennas follows. The mineral pigments were prepared by washing or grinding the original material as received and by calcination of the yellow ocher and brown sienna with and without manganese dioxide to produce red, brown, and black colors. These prepared powders were tested for fineness, oil absorption, and color as compared with well-known brands of commercial pigments. Similar tests were made with several basalt red clays occurring in the neighborhood of Salem, Oreg., and Kalama, Eatonville, and Clay City, Wash. The color particularly was studied, since this property is the most important commercial characteristic of the minerals. PURPOSE OF INVESTIGATION Since the development of the clay industry in the Pacific Northwest, some curiosity and interest have been aroused by the red and yellow clay or ocherouslike material that has often been found associated with the commercial clay deposits. These include the red and yellow "paint pots" near Deer Park and Spokane in eastern Washington, a red clay at Clay City, another close to Eatonville in western Washington, and red basalt earths near Salem, Oreg., and along the Columbia River near Kalama, Wash. Several companies have been organized to produce pigment colors from two of these deposits but have either discontinued or never started operations.

Jan 1, 1929

By Dwight L. Sawyer, Roy T. Sorensen

The Bureau of Mines has investigated the recovery of alumina by hydrochloric acid leaching of calcined kaolinitic clay . Bench- scale studies indicated that horizontal belt filtration was a pprraaccttiiccaall method for separating the siliceous residue from aluminum chloride liquor generated in the leaching step . Miniplant -scale continuous testing was performed to evaluate the filter circuits and to compare filtration response of different calcined kaolin feed materials and of different agitatorbaffle designs in the leaching reactors . Soluble alumina recovery with a single filter ranged from 94 pct with minus 10 -mesh feed more than 96 pct with minus 35-mesh or misted feed . Process advantages were confirmed for the calcined misted kaolin feed material prepared by a Bureau-developed misting process . With two filters in series , an overall filtration rate of 100 lb solids /hr.ft - 2 of filter area was attained with a soluble alumina recovery of more than 99 pct . More than 99.5 pct alumina recovery was obtained with a thickener and a two - filter circuit for either the minus 35-mesh or the misted feed . Modifications in leaching reactor design made to decrease particle- toparticle attrition were successful and significantly increased filtration rates and decreased flocculant requirements .

Jan 1, 1965

By L. F. Christianson

The presence of salt in crude petroleum has been known for many years, but recently the percentage of chloride salts of calcium, magnesium, and sodium produced with some crude oils has increased to such an extent that the removal of the salty compounds is imperative for some refiners and their presence causes considerable apprehension for others. The exact reason for this increase of salts is not known definitely, but in all probability a combination of factors contributes to the condition. The most important are acidizing of wells, development of new fields producing crude oils of greater salt content, and the depletion of old fields with an attending increase in the production of emulsified brine. Due to handling

Jan 1, 1938

By C. M. McCulloch

The natural vertical fracture system in bituminous coalbeds is called cleat. Cleat orientation commonly controls the direction of mining with major development paralleling the face cleat. Previous researchers have categorized the origin of cleat as endogenetic, relating the origin of cleat to compaction and coalification, and exogenetic, relating the origin of cleat to tectonic forces. In the coalbeds studied for this report it was found that tectonic forces were the controlling factor of cleat formation. Face cleats were formed as extension fractures during structural deformation, and butt cleats, as release fractures during erosion and uplift. The face cleat of the Pittsburgh coalbed rotates from N 80° W in north-western West Virginia to N 57° W in southwestern Pennsylvania; the face cleat maintains a perpendicular orientation to the shifting axial trend of local structures. Cleat orientation in other bituminous coalbeds in Virginia, Utah, Oklahoma, and Central Pennsylvania showed a similar relationship to local structure. Directional permeability of coal is directly related to cleat. Holes drilled perpendicular to the face cleat yield from 2.5 to 10 times the amount of gas released as compared with holes drilled perpendicular to the butt cleat.

Jan 1, 1974

By D. Harrington

Most of those in the Health and Safety Branch, Bureau of Mines, necessarily participate in activities associated with essentially all phases of the mineral industries, including coal and noncoal mines, quarries, smelters, metallurgical plants, and various petroleum operations. One of the strictly war activities of the branch - the Explosives Control Division, which administers the Federal Explosives Act of December 26, 1941 - has functions that require contacts not only with nearly all phases of the mining and allied industries but also with those engaged in scores of other occupations that manufacture, store, use, or possess explosives, or many of the ingredients of explosives. The field men of the Health and Safety Branch (approximately 300 in number) Are occupied full time in health and safety activities and annually make thousands of contacts with people in the mineral industries as well as the plants in which they work. From these they formulate several thousand written reports containing sources of thousands of conclusions and recommendations aimed at reduction of health end safety hazards in these industries. Although such activities have been greatly increased during the war and immediate pro-war periods, they have been in effect to a considerable extent since the Bureau of Mines was created in 1910.

Jan 1, 1944

By L. F. Christianson

The presence of salt in crude petroleum has been known for many years, but recently the percentage of chloride salts of calcium, magnesium, and sodium produced with some crude oils has increased to such an extent that the removal of the salty compounds is imperative for some refiners and their presence causes considerable apprehension for others. The exact reason for this increase of salts is not known definitely, but in all probability a combination of factors contributes to the condition. The most important are acidizing of wells, development of new fields producing crude oils of greater salt content, and the depletion of old fields with an attending increase in the production of emulsified brine. Due to handling

Jan 1, 1938

By Sam McNary

The U.S. Bureau of Mines used the East Fork Pine Creek watershed to conduct a pilot study for an inactive and abandoned mine lands inventory, during which techniques and methodologies would be developed for subsequent inventories. A total of 177 waste dump samples, 191 mill tailings samples, and 36 stream sediment samples were collected. Water samples were collected from 18 sample sites during five sampling events. Waste dump, tailings, and stream sediment samples were analyzed for antimony, arsenic, cadmium, copper, iron, lead, mercury, and zinc. Results indicate a multidisciplinary approach is necessary: disciplines should include geology, geostatistis, geochemistry, geophysics, biology, hydrology, and remote sensing; small prospects do not generally contribute to watershed contamination, major mine and mill sites may contribute metal enriched sediment of metal enriched water; speciation studies and bioavailability studies are important.

Jan 1, 1995

By J. E. Geier

This Bureau of Mines report reviews hypotheses for the mechanism by which water jets reduce the specific energy of cutting for drag bits. Several of these hypotheses are shown to be inconsistent with published evidence and new observations. The notion of a limiting cutting speed, above which water jets would be incapable of rendering assistance, is shown to be improbable. The hypothesis that seems most plausible is that specific energy reductions are mainly due to the erosion of crushed materials from in front of the bit. This hypothesis leads to a prediction that, for a given rock type and jet-bit configuration at a constant depth of cut, the reduction in bit forces should be a function of dM/dx, the jet energy spent per unit length of cut. This dependence upon dW/dx is shown to be consistent with other workers? results.

Jan 1, 1987

By McClelland. John J.

This Bureau of Mines report discusses recent applications of water in-fusion technology to control dust in U.S coal mines and presents recommended guidelines for determining coal seam infusibility. The techniques required to use water infusion are presented in detail. A Bureau case study indicated that water infusion reduced dust levels by 68 pct along a longwall plow face, bringing this section into compliance with the Z.0-mg/m3 Federal dust standard. Similar studies conducted by Occidental Research Corp. under a Bureau contract show water infusion at two longwall double-drum shearer operations produced dust reductions ranging from 38 to 50 pct. Water infusion was found to be cost effective, aver-aging 5 cents per ton.

Jan 1, 1987

By John O. Atkins

[Experiments were conducted by the Bureau of Mines on five types of simuated lunar rock (dacite, tholeiitic basalt, vesicular basalt, pumice, and uluth Gabbro) to study the effects of various simulated lunar environments n their strength and deformational properties. Specimens were tested in an ltrahigh vacuum (UHV) system at pressures ranging from atmospheric down to 0-11 torr and at temperatures of -130°, 20°, and 135° C. All tests were onducted with a servocontrolled testing machine. Rock specimens tested at 0° C in UHV exhibited significantly higher compressive strength and Young's odulus than those tested at 20° C in atmospheric pressure. The magnitudes f increase are related to the porosities and permeabilities of the rock pecimens; high porosity and permeability allow better outgassing and thus nprove surface cleanliness in UHV. The compressive strength generally ncreases but Young's modulus decreases as test environments change from 20° C i UHV to 135° C in UHV. No significant difference was observed in the iysical properties measured at 20° C in LTV and -130° C in UHV. Anisotropy i strength and Young's modulus exist both in UHV and at atmospheric condi¬'.ons with the same symmetry pattern. The orientations of the principal axes iy, however, change from the atmospheric to UHV condition. The results idicate that rock fragmentation in lunar environment will require more ergy than that at 20° C in atomospheric pressure.]

Jan 1, 1974

By William G. Pariseau

A small displacement-small strain finite element technique utilizing the constant strain triangle and incremental constitutive equations for elastic-plastic media that are nonhardening and obey a Coulomb yield condition has been applied to the analysis of gravity flow initiation in a V-shaped hopper containing a powder under lunar environmental conditions. Three methods of loading were examined. Of the three, the method of computing the initial state of stress in a filled hopper prior to drawdown by adding material to the hopper layer-by-layer is superior (as expected). Results of the analysis of a typical hopper problem show that the initial state of stress, the elastic moduli, and the strength parameters have an important influence on material response subsequent to the opening of the hopper outlet.

Jan 1, 1971

By R. L. Grayson, L. L. Probert

"A three-year project focusing on the depth profiling of respirable coal mine dust particles using scanning electron microscopy coupled with energy dispersive X-ray analysis resulted in the development of statistically classified particle-behavior models. The models depict the changing silicon fraction for particles at 5-, 7-, 9-, and 11-keV accelerating voltages, thereby giving a clear indication of the nature of various types of mineral particles. This paper focuses on the results for respirable quartz particles sampled from five underground coal mines across the US. Through statistical analysis of results the relationship between the fraction of surface available quartz in respirable dust samples and coal rank is established for three Pennsylvania coal seams. IntroductionThis is the last in a series of papers detailing the results of SEM/EDX-based analyses of respirable coal mine dust particles collected from field sampling. Previous papers have detailed preliminary results and the statistical validity of the methodology (Grayson, Andre, and Simonyi, 1990; Grayson, 1991). This paper presents the final results of the analysis of respirable dusts from five coal seams with a range of coal rank:• Lykens Valley seam (anthracite), eastern Pennsylvania• Brookville (A) seam (mid-vol bituminous), central Pennsylvania• Pittsburgh seam (high-vol B bituminous), western Pennsylvania• No. 6 seam (high-vol C bituminous), Illinois• Wadge seam (sub-bituminous A), ColoradoSEM/EDX-based techniques were applied to try to clarify the role of quartz as an etiologic agent in coal workers' pneumoconiosis (CWP). It was hypothesized that previous studies were hampered by the restrictions of bulk analysis techniques and that particle-level analyses were needed to answer a number of questions concerning the role of quartz in CWP and its progression.Since 1985, a large number of the respirable dust samples submitted to MSHA are analyzed for free silica (Tomb, Parobeck, and Gero, 1986). Our reasearch shows that conventional bulk analysis techniques may not give a true indication of the biologically available, or active, quartz in mine dusts. Analytical evidence indicates that respirable dust samples may contain many quartz particles that are occluded, or coated, resulting in a bulk analysis for ""free silica"" that may not be indicative of the biologically available quartz surface."

Dec 1, 1996

By R. G. Dressler

The Federal Bureau of Mines designed, constructed, and operated a demonstration plant at Louisiana, Mo., to produce gasoline, liquid fuels, and organic compounds from coal by a modified Fischer-Tropsch gas-synthesis process. Satisfactory equipment was developed to produce and purify synthesis gas and convert it into the desired products. Coal or coke was gasified with oxygen and steam to make a gas consisting essentially of carbon monoxide, hydrogen, and carbon dioxide. Dust in the raw gas was removed by cyclone separation, water scrubbing, and electrostatic precipitation. Carbon dioxide, hydrogen sulfide, and organic sulfur were removed with diethanolamine, iron oxide, and activated carbon. The gas was passed over iron catalyst and was converted into synthetic liquids, which were then separated and fractionated into gasoline, diesel oil, other liquid fuels, and oxygenated organic compounds. A 39-day continuous run demonstrated the feasibility of the process. Addition of 3 milliliters of tetraethylead per gallon of upgraded (or finished) gasoline gave a product with an octane rating up to 90 by the research method. After a caustic wash, the diesel oil was of a superior quality; its cetane number was 60 or above.

Jan 1, 1961

Note: This is a progress report and therefore not necessarily conclusive. Further data may result in conclusions somewhat different from those reported here. Crop Growing Season The monthly average temperatures, total precipitation, and evaporation for the demonstration mine are shown in Table 1. [ ]

Jan 1, 1980

By George Quackenbos

The principal objective of this Program is the design, fabrication and testing of an Environmental System for operation in underground mines, to assess the effect of various mining systems on the contaminant levels near the mine face and within return airways. In order to determine the effect on airborne contamination in mines resulting from the development of new mining techniques, equipment and control systems, a Comprehensive Monitoring System is required to assess such contamination levels at critical and strategic locations and relate this information with ventilation parameters. The three variables to be sensed on a continuous basis are airborne dust concentration, methane concentration and ventilation air velocity. Each Monitoring Station will consist of a self-contained unit containing a power source and sensors to monitor the three above mentioned parameters. Ruggedness, reliability, ease 'of operation and intrinsic safety are important design objectives. Data gathered by each Monitoring Station will be fed to a Central Data Acquisition System by means of a portable transfer unit.

Jan 1, 1982

By D. R. Tesarik

Displacement and stress changes in cemented backfill and ore pillars at the Buick Mine, near Boss, MO, were monitored by engineers from the U.S. Bureau of Mines and The Doe Run Co., St Louis, MO. A test area in this room-and-pillar mine was backfilled to provide support when remnant ore pillars were mined. Objectives of this research were to evaluate the effect of backfill on mine stability, observe backfill conditions during pillar removal, and calibrate a numeric model to be used to design other areas of the mine. Relative vertical displacements in the backfill were measured with embedment strain gauges and vertical extensometers. Other types of instruments used were earth pressure cells (to identify loading trends in the backfill), borehole extensometers (to measure relative displacement changes in the mine roof and support pillars), and biaxial stressmeters (to measure stress changes in several support pillars and abutments). Two-and three-dimensional numeric codes were used to model the study area. With information from these codes and the installed instruments, two failed pillars were identified and rock mass properties were estimated.

Jan 1, 2010

By J. M. Goris

The U.S. Bureau of Mines, in a cooperative project with the University of Utah, Salt Lake City, UT, and Homestake Mining Co., Lead, SD, conducted in situ monitoring and numerical modeling of rock masses supported with cable bolts in two mechanized, cut-and-fill stopes and a shaft pillar at the Homestake Mine. Extensometers were used to measure rock displacement, while cable bolt strain gauges were installed to measure loads on both conventional and birdcage cable bolt supports. These instruments provided an assessment of rock mass behavior during mining as well as essential data for verifying results from computer analyses. The numerical modeling program FLAC was used to analyze cable bolt patterns and supports. Results from the evaluation study indicated that cable bolt strain gauges and extensometers were effective instruments for monitoring the behavior of rock masses supported with cable bolts. Also, numerical modeling of the 4S-48N stope using the FIAC code provided displacement values comparable with measurements from field extensometers.

Jan 1, 1993

By R. J. Hundhausen

The Shamrock copper-nickel mine in Jackson County, Oreg., was formerly a part of the Chisholm mercury property. In 1948 new owners advanced the old workings 40 feet to reveal encouraging widths of copper-nickel sulfide, ore on the Shamrock claim. When the owner's funds became exhausted, the Bureau of Mines carried on the development in 1949-50, completing 1,650 feet of bulldozing trenching, 396 feet of drifting, and 3,419 feet of diamond drilling. The Bureau's trenching disclosed a separate surface deposit 600 feet south of the mine deposit. This and the previously known deposit subsequently were diamond-drilled. The underground deposit has a known length of 100 feet, a dip length of. 100 feet and a width varying from 1 to 25 feet. The surface deposit is 200 feet long, 200 feet deep, and 5 to 38 feet wide. Neither deposit has been entirely delimited by development to date.

Jan 1, 1952