Search Documents

By James J. Snodgrass

A new technique was used to obtain detailed sonic logging data in drill holes above the water table at a coal mine site in northeastern New Mexico. The equipment was developed under contract to the Bureau of Mines and the U.S. Department of Energy to indirectly evaluate the in situ structural properties of coal and overburden. The system comprises a hydraulically operated, wall-clamping downhole probe compatible with standard four-conductor logging cable, and a surface control module. Resolution of layering is 0.6 meter (2.0 ft), and a redundancy of data from separate receivers provides accurate timing measurements. Preliminary results in the settled overburden of an excavated long-wall panel indicated a low average velocity zone, extending approximately 18 meters (60 ft) into the immediate roof of the coal seam. Subsequent measurements improved the field and recording procedures to produce high quality waveforms from which both P and S arrivals may be visually interpreted. Over a representative section of interbedded sandstone, siltstone, shale, and coal, Vp and Vs varied considerably even within lithologic units. Compressional wave velocity in the coal seam, Vp = 1,740 m/sec (5,700 ft/sec), was in the range of variability of published data.

Jan 1, 1982

By R. J. Pokora

This Bureau of Mines report is an applications manual that can be used by the nonmetallic mining industry for guidance in installing noise control materials into crushing and screening plants. These noise control modifications were installed and successfully tested at three operating quarries. This report identifies the major noise sources that can be encountered in crushing and screening plants, and discusses the applicable noise control materials and techniques that a plant operator can utilize on a retrofit basis to reduce equipment noise.

Jan 1, 1984

By R. F. Waters

Laboratory-scale selective volatilization methods developed by the Bureau of Mines to recover germanium and gallium concentrates from coal fly ash and phosphorus furnace flue dust are summarized. In the better experiments between 85 and 98 percent of the germanium was recovered as the lower oxide and as sulfides, and between 75 and 97 percent of the gallium was recovered as the lower oxide and as the trichloride. Grades of the condensates were inconsistent and varied between a few tenths of a percent and 8 percent, depending on the method used. In the primary extractions of germanium alone the degree of enrichment surpassed 100 to 1, and for gallium the best ratio was 30 to 1. Upgrading of condensates by vaporization retreatment and by leaching and precipitation is discussed. An appreciable degree of mechanical preconcentration by attrition scrubbing and elutriation was possible on two fly ash samples.

Jan 1, 1967

By Robert F. Chaiken

More than 500 fires are now burning in abandoned coal waste banks and coal deposits in the United States. Once established, such fires can burn for decades, and extinguishing them by conventional methods such as surface sealing to exclude air, excavation to remove fuel, or flushing to cool the fire zone is usually difficult and always expensive. Burnout Control, a technique developed by the Bureau of Mines for the control of abandoned fires, involves the accelerated combustion of coal in place with total management of the heat and fumes produced. A burning waste bank or mine is placed under negative pressure relative to the atmosphere, and heat and combustion products are drawn from the combustion zone through an exhaust ventilation system. Heat produced appears as sensible heat in the exhaust, at temperatures as high as 1,000° C (1,832° F), and can be recovered for the production of steam, hot water, process heat, or electricity. The Bureau's first field demonstration of Burnout Control was at Calamity Hollow in Allegheny County, PA (near Pittsburgh). Calamity Hollow was the site of an underground mine in the 1900's and was surface mined in the 1940's. In the winter of 1961-62, a fire of undetermined origin was discovered in the exposed coal. In 1963, the Bureau constructed a trench barrier around the fire and a surface seal over the affected area. The fire was isolated, but not completely extinguished. In 1979, when the Bureau began work on the Calamity Hollow Mine Fire Project, to demonstrate controlled burnout, the fire was still smoldering on the hot side of the trench barrier. The project, which was begun in December 1979 and ended in July 1982, consisted of the design, construction, operation, and subsequent dismantling of a Burnout Control ventilation system. This report is the fourth in a five-part series that describes the Calamity Hollow Mine Fire Project. The first report, part 1, describes the design and construction of the field installation. Part 2 will present the results of a continuous 4-month burnout operation. (Because part 2 involves the analysis of a substantial body of data, it will not be published until after publication of parts 3, 4, and 5). Part 3 describes the instrumentation used to control and monitor the progress of the burnout operation. This part (part 4) and part 5 both deal with the closeout phase of the field demonstration. The quenching of the fire is described in this report, and part 5 will describe the final excavation and backfilling of the heated zones. The reports in this series document the Calamity Hollow controlled burnout demonstration, which showed that (1) controlled in situ combustion is a feasible method for controlling underground fires in abandoned mines, (2) the resultant thermal exhaust output is sufficient for energy utilization, and (3) water injection with fume exhaustion is a potentially effective method for cooling large underground fire zones. Further trials of both Burnout Control and water injection with fume exhaustion are planned.

Jan 1, 1984

By Thomas M. Barczak

This U.S. Bureau of Mines (USBM) report evaluates the load supporting characteristics of grout columns used as point supports for mine subsidence abatement. The cone-shaped columns were constructed with sodium silicate and cementitious grout in both wet and dry environments. The scope of work included the testing of seven full-scale grout columns in the USBM's Mine Roof Simulator from which the load-deformation and failure characteristics were determined. The performances of grout columns are analyzed with respect to (1) the amount of roof contact established during column construction, (2) shape effects produced by the truncated cone geometry, (3) size effects in reference to grout strength and full-scale column capacity, (4) the effect of wet environments on grout strength, (5) the effect of the sodium silicate on the grout strength and full-scale column behavior, and (6) the stiffness of the grout column. Limited tests were also conducted on cylindrical columns constructed in fabric bags. Recommendations for point support construction using sodium silicate technology and the need for additional research to develop improved containment devices for column construction are addressed in the report.

Jan 1, 2010

By Mildred Nadler, Alvin Kaufman

To aid industry and Government in planning water developments the Bureau of Mines in 1963 canvassed mineral producers to determine water use in 1962. Water use by the mineral industry comprises only 2 percent of the water withdrawn by industry as a whole. The major water-using mineral industries are natural gas processing, phosphate rock, sand and gravel, and iron ore. Analysis indicated the following conclusions: 1. Total water use and new water intake is dependent on the quantity of material processed and the process water requirements of the particular indus- try or commodity. 2. Recirculation is dependent on the processing requirements of a par- ticular commodity, the manner in which the water is used, cooling and condens- ing requirements in certain large industries, the quality of new water intake, and the need to treat new and discharged water. 3. Consumed water is dependent on the quantity of water recirculated, the temperature and humidity in the area, and the proportion of water used for cooling and condensing. 4. A threefold increase in water use by the mineral industry by 1985 is forecast.

May 1, 1965

By Hal J. Kelly

A picture of the ceramic industrial potential of the Pacific Northwest States is presented by reviewing the present ceramic industries, raw-material resources, and current market demands. A resume is given of the industrial plants manufacturing ceramic ware as well as available information on raw-material resources. No attempt was made to prospect for new deposits but rather to evaluate, insofar as possible, those already known. Since much of the industry is concentrated on the Pacific coast, most of the information available on resources concerns deposits in that area. Large, undeveloped districts in Montana and Idaho, however, offer promise of larger reserves of ceramic raw materials. Average annual production, some operating costs, and annual power consumption are given for each of the plants. Production and some cost figures are listed to show the limited nature of the present industry and to suggest fields open for new development.

Jan 1, 1956

By P. N. Summerfield

This report describes the first phase of a general investigation designed to ascertain whether an electronic roof-testing device can be developed that will improve the ability to detect "loose" or "drummy" roof rock over that possible by striking the roof with a sounding bar and noting the character of the air vibrations with the unaided ear or the rock vibrations with the fingers. The amplitude, frequency content, and duration of the vibrations produced by striking solid and drummy roof rock with a hammer or sounding bar have been measured. Results disclosed that there is a significant difference between the characteristics of the vibrations produced in solid and drummy roof. This difference is such that the design of an electronic device to indicate quantitatively the condition of the roof rock appears possible. INTRODUCTION The conventional method of roof testing consists of striking the roof with a bar2/ and judging its soundness from the character of the air vibrations heard with the ear and/or the rock vibrations felt with the fingers -a procedure that depends upon the experience and the sensory abilities of the observer. Impact testing of a solid roof rock usually produces a sharp ping or click, whereas impact testing of a drummy roof rock produces a dull thud or drummy sound. This method of roof testing is, at most, only a qualitative test, and many roof rocks are difficult to classify as drummy or solid.

Jan 1, 1956

An accelerated and coordinated program of coal research is believed by many to be a necessary step in assuring coal's proper position in the expanding energy market. The President's Advisory Committee on Energy Supplies and Resources Policy, for example, made the following recommendation: We recognize that coal is a great national asset and endorse a cooperative study to determine what research and development could be undertaken. The coal industry and both Federal and State Governments should participate in this study and its costs. Representatives of the coal industry have agreed that such a study should be initiated. Accordingly, Felix E. Wormser, Assistant Secretary - Mineral Resources, United States Department of the Interior, requested the Bureau of Mines and Bituminous Coal Research, Inc., to conduct a survey of current research on bituminous coal. In addition to this survey, studies were made to determine research projects that would be of value to the coal industry.

Jan 1, 1956

By G. E. McElory

"INTRODUCTION The subject of mine and tunnel ventilation has two broad aspects - (1) what atmospheric conditions to obtain in underground openings and (2) how to maintain the desired conditions efficiently. The first relates primarily to quantity requirements of ventilating systems, whereas the second relates more particularly to pressure requirements. Both, therefore, determine power requirements, which is the deciding factor in any system of mine or tunnel ventilation.Both divisions of the subject have received considerable attention from the Bureau of Mines since its inception in 1910 in the form of research, service, and correlation and dissemination of information. Numerous papers on various Phases of the subject have been published, of which a selected list, numbered and arranged in chronological order by type of publication, will be found at the end of this Paper. One of these, Technical Paper 705 (25) 2/ gives a complete bibliography of Bureau of Mines publications dealing with health and safety. As indicated by the selected list of publications accompanying this paper, the health and safety aspects have received most of the attention devoted to this work, chiefly because these have been dominant factors in Bureau policy, but partly because these aspects lend themselves to laboratory research and small-scale field studies. Although considerable attention has also been devoted to the engineering aspects of mine and tunnel ventilation, there has been, in the opinion of the author, who has been engaged on this phase almost continuously for the last 30 years, only sporadic recognition of the vital effect this phase of the work could have on improving health and safety conditions. As a matter of fact, ventilation activities have constituted but a very minor part of the total work of the Bureau of Mines, as, except for a few years in the nineteen twenties, there have been only a few short intervals when more than two or three men were engaged in field work and a similar number in laboratory research directly related to mine gases or mine air."

Mar 1, 1950

By John E. Lambert

Automatic control of drum head continuous mining machines was investigated as a means of reducing respirable dust generated and operator variabitity. Literature survey, manufacturer interviews and mine visits were the major information sources. Technically feasible automation concepts were Identified to control sump and shear rates, cutter head elevation limits and sumping distance. These are the elements of a programmed cutting cycle which maintains peak penetrating force on the cutter, to maximize depth of cut and therefore reduce dust generation. Based on the industry surveys, successful underground hardware demonstrations must be completed in order to stimulate the market demand for these advanced control features.

Jan 1, 1979

By T. W. Johnson

The Bureau of Mines, in cooperation with the Natural Gas Department of the American Gas Association, has in progress a study or the flow of natural gas through high-pressure transmission lines. A major problem of this study is to compare the deliveries calculated from the gas pipe-line flow formulas commonly used, with the metered deliveries from pipe lines in operation. In order to obtain such comparisons a series of tests has bean made on 25 operating pipe lines in Kansas, Oklahoma, Louisiana, Arkansas, Texas, and California ACKNOWLEDGEMENTS Study of the flow of natural gas through high-pressure transmission lines was made under the general supervision of H. H. Hill, former chief petroleum engineer of the Bureau of. Mines, H. C. Fowler, acting chief petroleum engineer of the Bureau of Mines, N. A. C. Smith, superintendent of the Bureau of Mines Petroleum Experiment Station at Bartlesville, Okla., and T. Brandenthaler, chief of the oil and gas action of the Bartlesville station.

Jan 1, 1929

By E. V. Cilento, R. C. Laotz, K. A. DiGregorio

"PULMONARY ALVEOLAR macrophages (PAM) protect the lungs by providing a first line of defense against inhaled foreign debris and bacteria. In this role PAM phagocytize foreign matter, secrete enzymes that augment microbial killing and digestion, and produce reactive oxygen me-tabolites (2, 3, 18, 19, 22, 26). However, in addition to this antibacterial function, PAM participate in a diversity of functions, such as tissue repair, lipoprotein metabolism, and immunoregulatory activities (11, 22).Studies have suggested the existence of a heterogeneous population of PAM with respect to immunologic function, enzyme release, phagocytosis, morphological characteristics, expression of membrane receptors, ad-herence, and superoxide (O2•) release (4-7, 10, 16, 21, 23, 28). This heterogeneity has been observed by analyz¬ing subfractions of PAM separated by cell density frac-tionation. For example, using guinea pig PAM, Dauber et al. (7) showed heterogeneity in cell density and size, morphological characteristics, and cytochemical properties, whereas Holian and co-workers (16) reported variations in migration, chemotaxis, O2• release, and pinocytosis among subfractions collected. Similarly, O'Neill et al. (21) observed functional heterogeneity in rat PAM with regard to phagocytosis, O2 • release, and lysosomal enzyme activity.Several investigations have reported a correlation between PAM activity and cell volume. Most studies have shown that O2 release from PAM increased with decreasing cell size (15, 21, 25), although Bielefeldt Ohmann and Babiuk (4) reported a decreasing trend. However, Gallin (13) has suggested that significant variability may even exist within density-defined or cell-volume subfractions that could lead to misinterpretation of results concerning PAM heterogeneity.A better understanding of the heterogeneity in O2 production may be obtained by using single cell meas-urements to evaluate whether functionally distinct sub-populations actually do exist. As such, the present study was designed to examine heterogeneity in O2 • release from single PAM using a recently developed electrooptical technique (8). The initial oxygen metabolite, O2•, produced by NADPH oxidase at the surface of the plasma membrane, was measured by quantifying the reduction of nitro blue tetrazolium (NBT I to a diformazan precipitate. Measurements were made from video recordings of individual cells stimulated by their adherence to the bottom of a culture dish. The cell volume and degree of spreading also were determined directly from the same video recordings, and the data were correlated with the initial rate and maximum amount of diformazan produced by the same cell."

Mar 1, 1992

By Manuel Gomez

This report presents low-temperature tar data from studies by the Bureau of Mines of tars produced in an externally heated (entrained state) pilot-plant-scale retort. Analytical data covering 20 low-temperature tars, derived from the. carbonization of various ranks of foreign and domestic coals, are tabulated. The character of the tar is discussed in relationship to carbonizing conditions and the rank of coal. It is seen that in carbonization techniques that employ entrainment or fluidization of the coal particle, carbonization conditions are secondary to coal rank with respect to tar-oil yields and composition. The influence of distillation conditions on recoverable yields of tar products is presented. The probable yield of commercially important chemical products, based on a ton of pure (moisture- and ash-free) coal, are predicted. INTRODUCTION Low-temperature tars produced by entrainment or fluidized carbonization techniques that employ internally heated reactors represent the most nearly primary tart produced by industrial processes. In brief, such a process involves the application of a heat gradient to the coal particle "boiling" or suspended in a turbulent state in the reactor chamber. Conditions are observed so that the coal particle remains suspended within the reaction zone by a gas stream for a time interval commensurate with maximum tar-oil yield. The heat necessary for the carbonization reaction may be obtained entirely from the hot (preheated) gas stream, or it may be derived partly from the combustion of the volatile products and char by the transport gases, usually air. The volatile material moves out of the carbonizing zone at a rate that approaches the velocity of the transport gas. Carbonizing conditions are ideal when a minimum particle residence time is obtained within the reactor at a given temperature and a maximum yield of condensable volatile matter is released. In industrial practice this objective is a compromise.

Jan 1, 1957

By A. J. Forney

Recent experiments used catalysts of plate assemblies in synthesizing high-Btu gas and gasoline indirectly from coal. A gas with a heating value of 925 to 943 Bt-: per cubic foot has been prod u la the hot-gas-recycle pilot plant from synthesis gas (3H2+100) with lathe turnings used as catalyst in the first reactor, and assemblies of parallel sprayed plats of nickel in the second. Solid plates made of Raney nickel, and steel and aluminum plates sprayed with Raney nickel or nickel oxide were tested. Those catalysts had very low resistance to gas flow; 90 percent lower than nickel granules used in previous experiments. In a single stage of synthesis thee nickel plates were only partially successful. Although the heating values of the product gas ranged from 856 to 941 Btu per cubic foot, the carbon monoxide content of he gas was above 0.1 percent. Both steel and wrought turnings were tested in single-stage synthesis, but the conversion of hydrogen and carbon monoxide was too low to attain the desired heating value of 900 Btu per cubic foot in the product gas. Assemblies of plates thermally sprayed with fusel iron were tried in an experiment to make gasoline. A gasoline yield of 52 percent (of the hydro¬carbons produced) was obtained using a 1H2-10O feed These sprayed assemblies were in service for 1,500 hours, the longest that this type of catalyst has been used. When a second reactor containing Raney nickel catalyst was added in series with the first reactor, complete utilization of the feed gas was obtained because in addition to the liquid product, a high-Btu gas with a heating value of 800 Btu per cubic foot was made.

Jan 1, 1965

By Vladimir Adamek

This paper describes the Bureau of Mines development of a novel subsidence prediction methodology suitable to the mining and geologic conditions in the Northern Appalachian Coal Region. It describes the computation of vertical and horizontal movements, inclination, curvature, and horizontal strains. The substance of this method is the separation of the effects of lithology by introducing a correlation between hypothetically homogeneous overburden and existing lithologic conditions, while providing for different mining conditions, i.e., underground geometry and overburden thickness. The effects of lithology have been expressed in the form of a variable subsidence coefficient within the subsidence trough. The subsidence co-efficient is considered a constant for other predictive methods. Field data from 16 test sites at 11 Bureau longwall panel studies were used in the analysis. For each panel, the characteristics of the variability of the subsidence coefficient were defined. Regression analysis of the subsidence coefficients from all test sites on their locations relative to the edges of their respective panels yielded a third-degree polynomial equation. The results from additional longwall panel studies, not included in the regression analysis, were used to prove the validity of this method. To facilitate the use of this precalculatlon methodology, a computer program was written in BASIC for use on a personal computer.

Jan 1, 1987

By J. J. Forbes

First - aid training is an essential part of safety programs in the mining industry , but it is only a means to an end ; first -aid training will not eliminate accidents , but unquestionably it is of considerable value in any accident prevention program . Numerous features should be incorporated in any efficient , well - developed safety plan ; in addition to first -aid training safety work , to be reasonably effective , should include the establishment and maintenance of a safety organization , safety competitions between mines or sections of mines , safety- inspection committees , accident - investigation committees , safety meetings of mine officials , safety bulletins and posters , employees ' safety publications , Holmes Safety Chapters (which provide for monthly safety meetings of all employees ) , and numerous other activities looking to safe operation of mine or plant . These features are supplementary to the fundamentals of safety-- adequate and effective supervision and discipline . Years of experience , however , have demonstrated that first - aid training is a good accident -prevention auxiliary and should be made an integral part of every company's safety program . Many safety-organization plans have failed because they have been based upon the assumption that the supervisory force should be given full authority and responsibility for achieving safety and eliminating accidents and that the workers , who are most vitally concerned , are nonessential . First -aid training causes the employees to feel that they have a personal and full participation in the safety program and is now available so readily that no individual or organization has any valid excuse for not having it . Early investigations made with a view to bettering health and safety conditions among the employees in the mineral industries demonstrated the need of prompt care of injured employees because , under the difficulties inherent in the occupation , seemingly unimportant wounds , when not treated promptly, became infected and caused permanent disability and even death . Many seriously injured persons , brought out of mines and plants by fellow workers who were ignorant of the approved methods of giving first aid or of safe means of transportation

Aug 1, 1934

By W. D. Dietzman

This Bureau of Mines report presents a profitability analysis of producing crude oil by waterflooding. Included are the estimated costs of installation of water injection and producing equipment for waterfloods at 2,000 and 4,000 feet and the estimated annual operational expenses for each in west Texas. Using these cost estimates as a base for selecting a range of costs that are indicative of producing crude oil by waterflooding, a simulation technique was derived for determining the profitability under various conditions. Because of the large number of combinations of variables used in this study, a high-speed digital computer was utilized for the calculations. The variables include operational expenses, capitalized costs, price of the oil, annual production, and leasehold acquisition cost. The results obtained from the simulations are presented Fn the appendix. In addition, a nomographical approach was chosen for presentation of the profitability. Five nomographs are presented that can be used for fast estimation of the discounted cash flow (DCF) rate of return that might be expected from a prospective or active operation under various sets of assumed conditions.

Jan 1, 1974

By J. B. Gayle

A half-ton experimental coke oven was installed at the Southern Experiment Station, Tuscaloosa, Ala., in 1948. Designated as the Tuscaloosa oven, this unit features a 17-inch carbonizing chamber, globar heating elements, and silica-brick walls designed to simulate as closely as possible the carbonizing conditions for commercial, slot-type ovens. The reasons for constructing an oven of this Size, the details of the design, and the operating characteristics of the oven have been given in previous publications.3/4 The present report deals with the reproducibility of test-oven data and the effects of variations in flue temperature on the physical properties of the cokes produced. Also included are the results of 2,400° carbonizing tests for several coals and coal blends not included in the earlier reports.

Jan 1, 1955

By Raymond G. Travis

This report describes coal-mining methods, power requirements, coal production and distribution, and coal resources of the Bull Mountain coal field in Musselshell and Yellowstone Counties, south-central Montana Investigations in the field, were conducted by Bureau of Mines engineers The report contains a short summary of the geology and geography of the field and discusses the following information secured during the field study: Method of mining practiced at each mine, including a description of each phase of the mining cycle. Coal produced and its distribution at each mine. Power requirements and the consumption of electricity per ton of coal produced by mines. Number of non employed by mines, and the production per man per shift underground and the over-all production per man employed. Estimates of future production and power requirements for the field as a whole. This information should be of benefit to any company or individual planning the development of now coal mines in the area or the expansion of present operations.

Jan 1, 1950