Search Documents

By A. E. Kasten

The contract objective was to develop and test automatic fire control systems for large surface machinery in surface coal mines. The effort described by the report covers the period from 31 January 1977 to 11 November 1977 and accomplished the following tasks: ? Data accumulation, mainly from visits to the major manufacturers and mine sites. ? Hazard analysis of blast-hole drill, mining shovel, and dragline. ? Recommended design concepts for automatic fire control systems for each of these vehicles. ? Detail system designs for each of these vehicles. ? Procurement of prototype systems for the blast-hole drill and mining shovel. ? Installation of the prototype systems on machines at a surface mine and demonstra¬tion of performance by fire tests on the machines.

Jan 1, 1977

The following pages discuss the objectives, the background, the scope and a statement of the problem of the study of methods to improve the pillar extraction practices in underground coal mines. 1. OBJECTIVES The objectives of this project were: ? to determine the principal factors contributing to high accident frequency and severity in both conventional and continuous mining operations; ? to compare and evaluate the safety aspects of the "open end" and "split and fender" systems of pillar mining; to establish basic data required to decide what constitutes an adequate pillaring plan that will optimize efficiency, recovery, and safety; ? to determine what measurements or information should be collected, (e.g. roof sag, pillar stress,) to make on-the-spot judgment of impending roof or pillar collapse; ? to make recommendations to improve existing methods or to insure proper techniques are implemented, and ? to suggest areas where additional studies or new research may be of value.

Jan 1, 1975

By Roy E. Williams

1. The major sources of heavy metal ions in wastewaters of the Coeur d'Alene Mining District are effluents from metallurgical processing plants. Effluents from mine operations provide a secondary source for heavy metal ions. Based on data analyzed by the Federal Water Quality Administration, mercury and arsenic are escaping from some mill waste ponds, but they are in the suspended phase. 2. Metallurgical process effluents are combined with mine waste effluents in tailings ponds, consequently, the quality of the tailings pond decant water is highly degraded. The major effect of combining metallurgical process effluents with mill wastes is a drastic change of pH in the tailings pond. This chance may be an increase or a decrease depending on the metallurgical process. The effluent from an electrolytic antimony plant drastically increases the pH in the tailings pond permitting the removal in solution of antimony via the pond decant system. The addition of low pH effluents to the tailings ponds results in a net decrease in pH which makes lead, zinc, cadmium, and copper more soluble, thereby permitting their removal from the pond via the decant system.

Jan 1, 2011

By Herbert H. Einstein

The innate variability of natural materials and processes causes uncertainty in the models representing the natural phenomena and uncertainty in estimating the parameters that are used in these models. Reliability analyses, in contrast to the traditional factor of safety approach, are well suited to a rational incorporation of uncertainty in design and exploration decisions. Probabilistic kinetic and kinematic analyses were developed and combined to form reliability analysis methods. With one method the reliability, i.e.) the probability of failure, of an individual 2-plane wedge in a slope can be determined. The other method is aimed at slopes with a single slope parallel set of joints. In each case two approaches were developed, an encompassing one relying on computer codes and a simplified or summary approach relying on charts or pocket calculator computation. A major contribution of these approaches is the treatment of joint persistance. Instead of having to assume a certain persistence, it is now possible to use exploration data on joint geometry and to include the persistence effect rigorously.

Jan 1, 1979

By C. O. Karacan, S. J. Schatzel, W. P. Diamond

In coal mining, longwall mining is a preferred method to maximize production by extracting large blocks of coal that have been outlined with a set of development entries. In U.S. mines, longwall panels are typically 305 m (1,000ft) wide (with a continual trend towards even wider panels), and usually over 3,050 m (10,000ft) in length. The increasing size of longwall panels, while helping to increase coal production, may also increase methane emissions due to the exposure of the mining environment to a larger area of fractured, gas-bearing strata. Thus, understanding the impact of increased panel widths on methane emissions, and designing gob gas ventholes and bleeder systems accordingly, can enhance the safety of the underground workforce by reducing their exposure to potentially explosive accumulations of methane/air mixtures. As part of its mine safety research program, NIOSH’s Pittsburgh Research Laboratory has initiated a reservoir modeling effort to better understand the interaction of the various geotechnical factors influencing gas flow within and to the underground longwall mining environment. A focus of this modeling effort has been 1) the prediction of the incremental amount of methane emissions to be expected due to increasing longwall panel widths, and 2) optimizing gob gas venthole completion practices to capture more of the gas in the subsided strata above longwall panels before it can enter the ventilation system of the underground workplace. The history matching phase of the study has been carried out on a 381-m (1,250ft) wide panel in the Pittsburgh Coalbed. Simulations have also been completed for a 442 m (1,450ft) wide panel to estimate the incremental increase in methane emissions and the performance of current gob gas venthole placement configurations. Additional venthole placement configurations were simulated to investigate options for optimizing methane capture from the subsided strata above the wider longwall panel.

By J. J. S. Sebastian

The process development described in this report was carried out at the Morgantown Station of the U. S. Bureau of Mines in cooperation with West Virginia University. An experimental laboratory-scale pilot unit to gasify coal dust in entrainment was constructed on the Campus of the University in Morgantown. The enormously accelerated demand for liquid and gaseous fuels and utilization of our immense coal resources require that a low-cost process be developed for the gasification of a wide variety of coals. Such a process would be a major factor in lowering the cost of synthetic liquid fuels. None of the proc3sses developed in Germany prior to and during World War II, such as the Winkler process, the H. Koppers dust gasification process, the Wintershall-Schmalfoldt process, etc., meet all the requirements for a low-cost process under American conditions. Nor has any other process designed and experimentally operated at atmospheric pressure during the post-war period in this country appeared to fulfill all of the necessary conditions for a low-cost process.

Jan 1, 1950

By Kenneth G. Skinner

Diatomite, also known as diatomaceous earth, diatomaceous silica, kieselguhr, and moler, has been used extensively for many years, but only during the past two decades has it become an important industrial mineral. United States sales for 1.936-38 totaled almost 280,010 tons,7 but relatively little (with the exception of that sold by an Oregon company affiliated with a larger California company) was sold by Pacific Northwest producers. In attempting to develop some of the many Pacific Northwest diatomite deposits, these producers have been handicapped by lack of published technical information regarding processing methods and the suitability of different deposits for specific uses. To determine some of the physical and chemical properties of known Pacific Northwest diatomites, the present investigation was started in 1938 by the Bureau of Mines in cooperation with the College of Mines, University of Washington. Figure 1 shows the location of deposits sampled. Because most relatively pure diatomites can be used as concrete admixtures or as inert fillers in rubber, paints, and plastics, this investigation concentrated upon determining some filter-aid characteristics and their relationship to other physical properties. A filter-aid is a powdered material that, when added to solutions to be filtered, improves flow rate, filtrate clarity, or both. Some chemical analyses also were made.

Jan 1, 1944

By Liming Yuan

A study of the ignition of non-fire-resistant hydraulic fluid sprays was conducted by the National Institute for Occupational Safety and Health. Both an open flame and a hot steel surface were used as the external heat sources. With the open flame as the heat source, the minimum oil temperature and minimum spray nozzle pressure that resulted in an ignition were measured. The effects of the distance between the open flame and the nozzle and the nozzle orifice diameter on the ignitability of the hydraulic fluid sprays were examined. With the hot surface as the heat source, the minimum surface ignition temperature was determined. The degree of oil atomization and the relative direction of oil injection with respect to the hot surface are discussed. The ignition of oil sprays from the impingement of oil jets onto a vertical surface was also investigated. Finally, the results are compared with those obtained for fire-resistant hydraulic fluids. Keywords: Ignition; hot surface; open flame; hydraulic fluid

Jan 1, 2006

By Henry P. Cole

A comprehensive review of published research was carried out to identify methods for teaching and assessing critical but nonroutine skills needed for coping with emergency situations. Specific methods for assessing critical skills proficiency in aviation, medicine, organization management, the military, and other industrial/technical workplaces are described. The potential application of these methods for teaching and assessing (1) critical first aid and (2) self-rescue and escape skills to underground coal miners in annual refresher training is explored. Research and development activities that may improve mine health and safety training are suggested. Most of these research and development activities were completed later in the project. This additional work is reported in the project technical report #2 and the final report. The research reported in the present document was completed in 1984 -85. Many of the initial findings reported in this document are updated in the later project final report.

Jan 1, 1988

By Christopher C. Jobes, Alan G. Mayton, Timothy J. Matty, Joseph P. DuCarme

Mining injury statistics show that a significant number of back, neck, and head injuries are linked to exposure from vehicle vibration. Use of a suspension seat is a common way to isolate the vehicle operator from the adverse effects of vibration exposure. Thus, researchers at the National Institute for Occupational Safety and Health1 – Pittsburgh Research Laboratory (NIOSH – PRL) performed laboratory studies on four passive and two semi-active seat suspension designs. These are typical of seat suspensions commonly found on large off-road heavy surface mining, construction and agricultural vehicles as either replacement or original equipment manufacturer (OEM) systems. One included a pneumatic (air bladder) spring mechanism. The fifth and sixth suspensions were a NIOSH magnetorheological (MR) semi-active damper design based on the pneumatic (air bladder) and one of the coil spring suspensions above. These suspensions were modified with a commercially available MR damper substituted for the OEM damper. These six seat suspension systems were tested and analyzed, for vertical vibration only, using the ISO 5007 Standard [1]. This paper describes the laboratory vibration tests using a MTS® shaker table and discusses the results obtained for the different suspension designs and highlights the rheonetic technology studied. Implications of the seat suspension designs relative to their capabilities for isolating vehicle operators from vibration exposure are discussed. Results for suspensions 1 through 3 showed frequencies of isolation from 2.1 to 3.0 Hz using the 40-kg (88-lb) mass and from 1.65 Hz to 1.8 Hz using the 80-kg (176-lb) mass. Suspension #4, in tests with only the 80-kg (176-lb) mass, showed an isolation frequency of 3.7 Hz. With the MR damper added to seat suspension #4, the peak transmissibility was lowered from 1.3 to 0.95 and showed a corresponding downward shift in frequency from 2.25 Hz to 1.4 Hz. In fact, the results for suspension #5 (the MR damper added to seat suspension #4), using test #3 conditions of the programmed control algorithm, showed isolation (attenuation of transmitted vibration) throughout the test frequency range from 1.0 to 6.0 Hz.

The compliance sampling method for coal mine dust in the United States has not changed appreciably in the last 30 years. A call for more frequent sampling with immediately available results is leading to new instruments that may supplement or replace the existing sampler. This report discusses two such instruments that provide immediate results of dust levels. The first, called the Respirable Dust Dosimeter (RDD), is designed to supplement the existing U. S. cyclone compliance sampling method. It uses the pressure drop across a filter to provide an inexpensive screening type of measurement. The RDD has been tested in the laboratory and a limited number of coal mines. Side by side testing has compared the RDD performance with personal coal mine samplers in triplicate area sample measurements. Results show that the differential pressure of specific filtration media can be an effective surrogate for respirable mass. Data show that there is a dependence on coal type and an effect of relative humidity. There also appear to be two distinct responses related to coal type. For specific coals the coefficients of determination, R2, are better than 0.9. For general use the detector tube, using laboratory generated calibration curves, can be used to estimate respirable dust levels. However, a calibration to a specific coal type may substantially improve the accuracy. Another sampler in development is called the Personal Dust Monitor (PDM). Designed to give compliance quality accuracy, the PDM uses the frequency change of a vibrating element to measure dust and give immediate feedback of results. Results of laboratory comparison of the prototype PDM sampler to personal gravimetric samplers indicate R2 values of better than 0.99 for three different coal types. Work is in progress to package the components into a person-wearable unit combined with a cap lamp system with a total projected weight of less than 1.4 kg (3 lbs).

By Robert L. Lappi

Volume I of this report described the demonstration of cross-ridge mountaintop coal mining. This document, Volume II, is intended for use as a supporting document to Volume I. This report describes the MATHMINE Mine Simulation System, a modularized software system used to support the demonstration of cross-ridge Mountaintop coal mining. The MATHMINE Mine Simulation System was used to generate mine plans for coal extraction at lowest cost. The functional details, data requirements and output of the software system are detailed here. The computer program was written in FORTRAN. One module which generates resource location data required the use of SAS?.

Jan 1, 1984

By Robert W. Geehan

The Bureau of Mines developed, by core drilling, the property of Nevada Scheelite, Inc., from October 5, 1943, to February 24, 1944. Claims of the corporation are near Rawhide in the northern portion of Mineral County, Nev. The purpose of the work was to determine possible reserves in the lateral and vertical extensions of a tactite zone which was being mined for scheelite. Production from this zone to January 1, 1944, was said to be 64,500 tons, with a recovery of 50,618 units of tungsten trioxide. The development work was done by the Bureau of Mines in cooperation with the U. S. Geological Survey and comprised a study of the geology, mapping the areas, and exploring the deposit by diamond drilling, trenching and sampling. Eleven holes were drilled for a total footage of 2,365 feet of holes.

Jan 1, 1950

By Sean Gallagher

This report was written in an effort to provide better control measures for low back pain (LBP) and low back disability in the mining industry. There are numerous factors associated with development of LBP, many of which can be effectively controlled while some cannot. Better job design is promoted as the best method of reducing cases of LBP and can also reduce the disability (i.e., lost time from work) associated with LBP when it happens. The report draws attention to what is currently known about LBP, what the causes are thought to be, and discusses recent back injury trends in the mining industry. Research describing unique physical demands in mining, such as the capabilities and limitations of working in awkward postures, is also presented. Methods that can be used to prevent initial LBP episodes are provided, including facilities design and layout for materials and supplies, use of mechanical-assist devices, improved design of lifting tasks, and better seat design. Methods of reducing the disability associated with LBP (including workplace design, proactive return-to-work efforts, communication, and management commitment) are also discussed. The report concludes that control of LBP and disability in mining requires a comprehensive approach to limit the repetitive loading that can occur on the low back due to manual materials-handling tasks and exposure to whole-body vibration (WBV). Specific recommendations include the following: ? Successful LBP prevention efforts require a proactive program that has strong management commitment and incorporates employee involvement. ? More efficient supply handling systems and use of mechanical-assist devices can greatly reduce exposure to hazardous lifting tasks. ? Lifting tasks should be designed to minimize low back stress. Tools to evaluate and redesign lifting tasks are presented. ? Improved seat design can reduce exposure to WBV and improve posture, leading to reduced LBP risk. ? The disability associated with LBP can be reduced. Getting the worker back on the job as quickly as possible is in the interest of everyone involved.

Sep 1, 2008

Provide long-term measurement of mine sidewall closure in backfilled stapes subject to flooding. Approach A water resistant extensometer is made by enclosing a rod-actuated transducer in a telescoping tube which is enclosed within an oil-filled outer housing. How It Works To assemble a water resistant extensometer, a cylinder -shaped transducer and two support rings are pushed into the small-diameter section of the telescoping tube where the transducer is held in place by friction. The outside of the small-diameter section of the telescoping tube is then greased and slid into the slightly larger-diameter section. See drawing. The cylinder-shaped transducer contains a potentiometer whose actuating arm is attached to a stainless steel extension rod that passes through one end of the telescoping tube. A similar rod is attached to the opposite end of the transducer body, and extends through the other end of the telescoping tube. A coil spring inside the large diameter end of the telescoping tube extends the tube

Jan 1, 1978

By W. L. Dare

This paper is one of a series being prepared by the Bureau of Mines on the methods and costs of mining uranium on the Colorado Plateau. The Continental No. l mine is at the south end of the Big Indian mining district, San Juan County, Utah. The mine is on a school section owned by the State of Utah and leased by Continental Uranium, Inc. A 70,000-ton uranium-vanadium ore deposit was discovered as a result of an exploratory drilling program completed in 1954.

Jan 1, 1957

By D. E. Van Dillen

Three-dimensional structural analyses of three instrumented areas of a deep, longwall coal mine have been performed using the finite element code BMINES. The three Instrumented areas include two single-entry portions and one double-entry portion of the Sunnyside No. 1 Mine, Sunnyside, Utah. The finite element models simulated the sequence of excavation in each test area: the advance of the entry, installation of structural supports, retreat of the longwall, caving behind the longwall, and accumulation and loading of the gob. The structural supports considered in these finite element models include rock bolts, wood cribs, concrete cribs, steel arch sets, and chocks. Mechanical simulation of the geologic environment is achieved through elastic/ perfectly plastic material models employing anisotropy to represent finely layered regions of the medium. The results of these calculations are com-pared with the instrumentation readings from the mine. These measurements include closures, crib loads, rock-bolt forces, and stress growth.

Jan 1, 1978

By J. C. Gerdeen

A new analytical model for the shear stiffness at a joint of the fully-grouted resin roofbolt is developed using the Theory of Elasticity and an analogy to a beam on an elastic foundation, Gerdeen [2]. The model developed in this study treats the elastic foundation modulus of the resin as being composed of both an elastic rock and an elastic resin. All previous attempts have neglected the elasticity of the rock and treated only the resin. A three dimensional finite element model of the bolt-resin-rock system is developed also and comparisons are made between the predictions made by it and the analytical solution. It is found that the agreement between the two representations ranges between 1.2% and 10.5%, with the greater differences being observed for systems of very large or very small bolt diameters and resin annulus thicknesses. Since such configurations are not the rule in practice parameter studies are performed using the analytical solution with the finite element solution being used as a check. For a 0.75 in. bolt, a resin annulus thickness of 0.1375 in., a resin with E = 7 x 105 psi and -1) = 0.210, and a rock of modulus E = 6.8 x 106 psi and V = 0.159 the shear stiffness is found to be 1.220 x 106 lb,/in, from the analytical solution and 1.245 x 106 lb,/in, from the finite element model. Applying the finite element model to the problem of the axial stiffness of the fully-grouted resin roofbolt a value of 6.002 x 106 lb./in. is obtained which proves to be at least 50% higher than any of the now existing analytical predictions.

Jan 1, 1976

By C. H. Fisher

Coal carbonization, the basis of a major industry, consists in heating coal in the absence of air at various temperatures (ranging from 500° to 1,000° C.) that are selected according to the kind of products desired. During this treatment, the complex organic substances that comprise the major part of the coal are converted into several useful products that are quite different from the original material. The principal products of coal carbonization or distillation are coke and gas. These products, as well as others of which lower yields are obtained (light oil, tar, and ammonia), occupy an important place in present-day commerce and civilization. This paper is concerned with the composition of the tar and light oil, which, as complex mixtures of organic compounds, are the source of many important dyes, inter-mediates, medicinals, resins, etc. The volatile products obtained when bituminous coals are destructively distilled or carbonized are tar, aqueous liquor, and gas. These products vary in composition and properties, depending on the nature of the coal and the temperature and conditions of carbonization. The tar is a dark, rather thick and viscous liquid at ordinary temperatures, becoming semisolid when cooled to the freezing point of water. The aqueous liquor (chiefly water) contains several inorganic substances and certain organic compounds, which, because of their solubility characteristics, have been extracted from the tar. The carbonization gases consist chiefly of carbon dioxide, carbon monoxide, hydrogen, hydrogen sulphide, ammonia, methane, ethane, ethylene, and several hydrocarbons of higher molecular weight. The hydrocarbons of higher molecular weight (benzene, toluene, xylene, etc.) may be re-moved as liquids from the gas by suitable means. This liquid and the first fractions obtained on distilling the tar are known as light oil.

Jan 1, 1938

At the end of August, U.S. producer posting of 99.5 percent unalloyed aluminum had been established at 48¢ per pound. At that time, dealer-quoted unalloyed ingot was reportedly at 44¢-47¢. CADMIUM: By late August, most U.S. producers had raised cadmium selling prices by 25¢ to $3 per pound. As a consequence, dealer quoting of cadmium ranged from $2.95 to $3.05 per pound. COAL: The wildcat strike, which began in southern West Virginia on July 19 and eventually spread to nine other States before ending on August 13, at its peak, idled approximately 115,000 miners and accounted for daily coal losses of an estimated 1.5 million tons at the height of the work stoppage. Concerned about the effects of the production cutbacks, the Bureau of Mines, early in the strike period, initiated its coal strike monitoring system which it had developed during the prolonged coal strike in the fall of 1974.

Jan 1, 1976