Search Documents

By W. W. Roepke

The Bureau of Mines has developed an interactive computer program that enables mine operators and others to identify the effect of cut-ting system changes on relative dustiness at the face. The program, which simultaneously evaluates machine parameters, coal seam parame-ters, and operator-controllable parameters, was developed for use on any microcomputer using BASIC programming language. The program allows the user to change one or more of the cutting system parameters at a time to see how these changes affect relative dustiness. A complete program listing and flowchart are included along with operating in-structions and sample outputs. An example showing how to use the program is also included.

Jan 1, 1985

By T. Bajpayee, J. Ellenberger

Microseismic monitoring and evaluation is one aspect of the National Institute for Occupational Safety and Health (NIOSH) research program. Roof falls are often preceded by a period of elevated microseismic activity, but not all periods of elevated activity result in a roof fall, nor do all roof falls occur after some amount of elevated activity. The objective of this study is to review periods of elevated microseismic activity and determine whether fracture activity rate can be used to anticipate the initiation of roof falls. The study was carried out at an underground limestone mine where major roof falls are associated with excessive horizontal stress. The progression of roof falls was detected by the microseismic signature produced by the rock falling from the mine roof onto the mine floor, which is termed a roof fall impact event. A total of nine elevated fracture activity periods that resulted in seven major roof falls were examined. It was observed that elevated fracture activity preceded the initial roof fall impact event in three out of four major roof falls. The initial impact event was not identified for the remaining three roof falls. Fracture event rates were analyzed and a roof fall alarm trigger of five fracture events in a ten minute time period was established for this test case. The fall alarm trigger was tested against six of the elevated activity periods. Four roof falls occurred in the six periods of elevated activity, and two would have triggered the alarm before the roof fall occurred, while two false alarms were generated. The results show that limited success would have been achieved by the microseismic system as a roof fall alarm trigger. However, the trigger would have been successful at warning of the onset of elevated activity, allowing mine employees to respond appropriately. The study highlighted some issues with implementing such a system in an operating mine, including the need for real time identification of fracture related microseismic signals among mining induced signals, and accurate location and identification of fracture clustering.

PRODUCTION of cesium, cesium salts, and rubidium salts in the United States declined somewhat from 1961 levels; rubidium production was virtually unchanged. Imports of pollucite declined because consumption was supplied partially out of inventory. Domestic Production.-About 50 tons of pollucite was reported mined at the Tin Mountain mine in the Black Hills of South Dakota. The Dow Chemical Co., Midland, Mich., MSA Research Corp., Callery, Pa., and Penn Rare Metals, Inc., Revere, Pa., produced a total of 159 pounds of cesium. Rubidium production remained essentially the same as in 1961. Shipments of the two metals by these companies and by American Potash & Chemical Corp., Trona, Calif., totaled 279 pounds. Production of cesium and rubidium salts by American Potash & Chemical Corp., Penn Rare Metals, Inc., and Rocky Mountain Research, Inc., Denver, Colo., declined substantially during 1962.

Jan 1, 1963

By N. T. Lowe

This Bureau of Mines publication presents salient deposit information in abstract form on 119 principal mineral deposits in the State of Nevada. Commodity coverage addresses 17 critical and strategic commodities that appear to have commercial production potential in the State. The core of the deposits described is taken from those properties evaluated d under the Bureau of Mines Minerals Availability Program (MAP); additional deposits are included to provide a more complete coverage. Institutional and infrastructural factors affecting mineral development are also discussed.

Jan 1, 1985

By E. Chin

The countries of Asia and the Pacific, with their large mineral resource base, are significant suppliers of a wide variety of minerals to both regional and world markets. Australia, China, and India dominate the commercial mineral exploitation in the region. Australia has known reserves of major minerals, which are adequate for both domestic demand, and for exports, and is a significant producer of bauxite; copper; diamond; gold; iron ore; lead; manganese; mineral sands (titaniferrous minerals, monazite, and zircon); nickel; salt; silver; tin; uranium; and zinc. China is the world leader in proven reserves of antimony, barite, ilmenite (titanium), magnesite (magnesium), molybdenum, rare earths, and tungsten. China also has large resources of low-grade iron ore and significant resources of other mineral commodities, such as coal, based on its production and export capabilities. India has significant resources of bauxite, barite, graphite, iron ore, and mineral sands.

Jan 1, 1995

By Robert B. McElwaine

"The demand for barite has increased greatly in the last 10 years, especially during World War II. Depletion of oil reserves and subsequent increase in deep drilling created a heavy demand by the oil industry for barite to be used as drilling mud. The great increase in demand for barite gave impetus to the development of a, deposit of impure barite near, Magnet Cove in Hot Spring County, Ark.The critical condition of the national barite supply early in 1944 led the War Production Board to recommend that the Bureau of Mines attempt to prove the existence of a large reserve tonnage of barite in the Magnet Cove area and arch for new deposits. To carry out this program, the Bureau explored on newly reported. Barite deposits in southern Montgomery County, Ark. The Gap Mountain, Fancy Hill, and Sulphur Mountain barite deposits were investigated. Eight diamond core-drill holes and 1,336 linear feet of surface trenching were completed, and barite samples obtained were analyzed, A study of the Montgomery County barnse district indicates that the lenticular bodies of barite replace a favorable host rock near the base of the Stanley shale formation. Barite is exposed along the side of anticlinal mountains where erosion has truncated the beds on the limbs of the associated synclines. An appreciable amount of barite suitable for commercial use has been indicated by trenching and core drilling. The Gap Mountain and Fancy Hill deposits are controlled by the Magnet Cove Barium Corp. and Baroid Sales Division of National Load Co., respectively. The ore is similar to that of the Magnet Cove area and is amenable to concentration by a flotation process. Mining of these deposits had not been begun by the time the Bureau completed its exploration project."

Nov 1, 1946

By John C. Edwards, Gene F. Friel

A series of liquid fuel fire experiments evaluated the comparative responses of five types of commercially available smoke detectors and a diffusion-mode carbon monoxide (CO) detector under normal and reduced airflow conditions based upon the alarm times of the detectors. These experiments were conducted in the Safety Research Coal Mine at the U.S. Bureau of Mines Pittsburgh Research Center. Two of the smoke detectors had manufacturer set alarms. For the other three smoke detectors, an alarm point was defined in terms of their background analog signal and the detector's electrical output noise under ambient conditions. A correlation was developed of the travel time of 5 ppm CO between pairs of CO detectors with the travel time calculated from entry and crosscut volumes and measured airflow. Based upon the relative performance of smoke detectors in this limited study, smoke detectors can be as effective as CO detectors for mine fire detection once identifiable alarm values are defined. Implementation of smoke detectors as part of an atmospheric mine monitoring system will improve mine safety.

Jan 1, 1996

By J. A. Organiscak

In the United States, respirable coal mine dust exposures are limited to a 2 mg/m3 time weighted average for a working shift. If the silica content of the sample exceeds 5 percent, the 2 mg/m3 standard is reduced according to 10- (% silica) to limit silica dust exposures to 100 µg/m3. Examinations of dust sampling data collected by the federal coal mine inspectorate showed that roof bolter occupations continue to be at risk for overexposure to respirable silica dust. Testing at the Pittsburgh Research Laboratory of the National Institute for Occupational Safety and Health assessed the effectiveness of a canopy air curtain for controlling occupational exposures to respirable silica and coal dusts. Initial testing found that zones of higher velocity airflow shrank as distance beneath the canopy increased. This suggested that protection from occupational dust exposures would likely decrease as distance beneath the canopy increased. Further testing revealed that coal dust reduction efficiencies were most affected by changes in interference air velocity and, to a lesser extent, changes in canopy air quantity. However, respirable silica dust percentages under the canopy were not affected by such changes and, in fact, were not significantly different from silica percentages measured outside the canopy. This implied that the air curtain was equally effective on both respirable coal and respirable silica dust particles.

Since roof falls in the vicinity of the working face in underground coal mines are a major source of fatalities and injuries in this country's coal mines, it is evident that the present systems of temporary support for use in this working area are ineffective. This seems to be chiefly due to the inconvenience of setting up heavy and awkward devices such as jacks, posts and the like, which also interfere with the movement of men and machines in this critical working area. This program was concerned with defining and testing commercially available materials that could be used as support elements in a more convenient flexible personnel shield. The objectives of this program were to: 1. survey the materials that might provide the support elements of a flexible-material personnel shield for use in underground coal mines and prepare a list of those materials which appear most suitable for use in coal mines. 2. prepare a proposed testing plan for the materials to be selected from the aforementioned list by the Bureau of Mines for further evaluation. The test plan was designed to provide the following information: a. Tensile strength. b. Proportional limit. c. Creep characteristics at room temperature. d. Elastic properties depicted by stress-strain curves. Properties were tested in two directions for woven fabrics. e. Density. f. Resistance to abrasion. g. Resistance to attack by mine atomsphere. h. Resistance to humidity. i. Impact characteristics.

Jan 1, 1972

By R. S. Dean

As set forth in the decision of the Trail Smelter Arbitral Tribunal, dated April 16, 1938 This Tribunal is constituted under and its powers are derived from and limited by the convention between the United States of America and the Dominion of Canada signed at Ottawa, April 15, 1935, duly ratified by the two parties and ratification exchanged at Ottawa, August 3, 1935 (hereinafter termed "the Convention") . . . The duty imposed upon the Tribunal by the Convention was to "finally decide" the following questions: (1) Whether damage caused by the Trail Smelter in the State of Washington has occurred since the first day of January 1932, and, if so, what indemnity should be paid therefor? (2) In the event of the answer to the first part of the preceding Question being in the affirmative, whether the Trail Smelter should be required to refrain from causing damage in the State of Washington in the future and, if so, to what extent? (3) In the light of the answer to the preceding Question, what measures or regime, if any, should be adopted or maintained by the Trail Smelter? (4) What indemnity or compensation, if any, should be paid on account of any decision or decisions rendered by the Tribunal pursuant to the next two preceding Questions? In this decision reported to the Government of the United States of America and to the Government of the Dominion of Canada, the Tribunal answered the first question in its entirety and reserved decision on the other three questions in accordance with the following extract from their decision

Jan 1, 1944

By Donald J. Barnes

There are no producing or developing mines in the study area. The only mineral production was stone from a basalt deposit near Indian View Point. Cinders and sand and gravel have been produced from deposits within 1/2 mi (0.8 km) of the boundary. Stone, sand and gravel, and cinder deposits inside the area are not considered resources because equal or better quality material is found closer to markets. The study area has no known oil and gas, coal, geothermal, or other energy related deposits. However, in 1982 application was filed on 25,000 acres (10,125 ha) of petroleum and on 15,000 acres; (6,0/5 ha) of geothermal leases.

Jan 1, 1983

By Nikolaos Polysos, Holger Witthaus

INTRODUCTION The classification system for German coal mining is the result of approximately 100 years of experience in roadway development and longwall mining. It is also based on different research projects covered by national and European research programs. Over the past 30 years, more then 600,000 m of road-ways have been driven and employed for mining activities. To properly describe the German rock mass classification system, therefore, it is useful to take a look at the main geomechanical preferences and common support systems. The decision about the most effective development technique and support system is based on a synthesis of rock mass classification and geomechanical analysis. The properties of surrounding rock, the in situ stress, and the influence of mining activities in several seams at each German mine must be considered for the evaluation of the expected deformation of the roadway. The mine layout, the requirements of ventilation and fire prevention, as well as the need to maintain emergency escape routes for the miners, require that the gate roads remain usable after the passage of the longwall face in most cases. Moreover, the gate roads must be maintained despite the high stresses that are applied during longwall retreat mining. Therefore, gate road design must address a broad spectrum of potential deformation environments. In the past, when gate roads were supported solely with yielding steel arches, lithologic descriptions of the surrounding strata conditions were adequate for the dimensioning of support and the prediction of the roadway deformation. The current conditions of multiple-seam mining at depths of up to 1,700 m require combined support systems, including pattern bolting and backfilled steel arches. Rock bolt support is used for development, after which (typically 50–100 m outby the face) the steel arches are installed and backfilled with building material (concrete) in order to achieve an optimized development rate. The rock mass classification system described below was developed especially for the conditions of German hard-coal mining. It includes the stress distribution caused by multiseam workings (including crossing goaf edges of former longwalls), as well as in situ stresses due to greatdepth and the presence of tectonic faults. It is based on the evaluation of four parameters: • Geotechnical analysis of drill cores • Geotechnical observation of the development face • Geotechnical classification of tectonic structures (faults) • Standard classification derived from geotechnical assessment and evaluation of stress conditions (using numerical modeling for stress calculation) ROCK STRENGTH One of the most important input parameters for describing strata conditions is the strength of the rock. The German classification system is based on a description of lithotypes. This method has been used successfully since the 1950s and is based mainly on the uniaxial compressive strength (UCS) of the material. An evaluation of the rock strength observed in a survey of approximately 82,500 samples of rock core yielded the results shown in Figure 1. The three most common coal measure rock types are mudstone, siltstone, and sandstone. Each shows a specific mean UCS level and a different spread between the minimum and maximum values. Sandstones, in particular, have a wide spectrum of compressive strength, ranging from approximately 40 MPa to greater than 130 MPa, with an average of 85 MPa. The causes of this wide range include different sedimento-logical preconditions, facies, and digenetic processes. [ ]

Jan 5, 2007

By Thomas P. Mucho, David C. Oyler, Jim Pablic, Dennis R. Dolinar

A room and pillar coal operation in central Pennsylvania was experiencing roof cutters and long running roof falls caused by high horizontal stresses. The roof conditions created hazards for the miners, and caused several production panels to be abandoned prematurely. The mine requested assistance from the National Institute for Occupational Safety and Health (NIOSH) in applying the "advance and relieve" mining to reduce the affects of the horizontal stress during panel development. The "advance and relieve" plan that was developed called for removing a pillar on one side of the panel as it was being advanced, thus creating a cave. The caving then relieved a portion of the horizontal stress across the panel. Because the horizontal stress direction is key to the success of this method, stress mapping as well as mining experience was used to establish the direction of the horizontal stress. Subsequent field measurements provided an estimate of the stress magnitude. Three panels were mined using this technique, and good roof conditions were achieved in all these panels. Instrumentation was used to monitor the stress changes in the roof created by the cave. Stress relief of over 1,000 psi was measured 120 ft from the cave and to depths of 20 ft into the roof. The lateral extent of the stress relief zone across the panels appears to be about 400 to 500 ft. This case history has provided much insight into the practical application of the "advance and relieve" method discussed in this paper.

By Arthur M. Hartstein

The Federal Bureau of Mines, under a contract with Ultrasystems, Inc., investigated the thermal oxidative degradation characteristics of conveyor belts used in underground mines. This included the determination of smoke evolution, glow characteristics, char yields, and the identification and quantification of all volatile decomposition products in the form of gram of specific product formed per gram of belt sample tested. In addition to these investigations, degradation studies were conducted on some pure ingredients used in conveyor-belt formulations. Three basic classes of belts were investigated: neoprene, polyvinyl chloride, and styrene-butadiene rubber compositions. The studies indicate that styrene-butadiene-based belts exhibit good flame resistance and are the least hazardous in regard to overall formation of toxic decomposition products. Under this program, thermogravimetric analysis was definitely established as a method of material differentiation.

Jan 1, 1976

By E. B. Kester

A study of the composition of the corresponding fractions of a primary and a high-temperature tar was undertaken to throw light on the net results of the pyrolysis of the primary products of coal decomposition in high-temperature coking practice, with reference both to total quantities of the chemically similar constituents and to their distribution throughout the boiling range. No exactly parallel investigations are on-record. The distribution of substances in high-temperature tars, however, is fairly well understood. Such tars are more or less similar, for they consist of the more stable phenols, aromatic and olefinic compounds resulting from the pyrolytic decomposition of a wide variety of primary tar constituents. For example, from a typical distillation curve for high-temperature tar phenols it may be seen that the greatest portion of the phenols distills between 180° and 220° C., a fairly narrow range. Low-temperature tars, on the other hand, are more complex, and hence exhibit dissimilarities from one to the next. Edwards, who has made a study of the acids, bases, and neutral oil of four low-temperature tar distillates, shows that the bases and neutral oil are evenly distributed among the fractions but that the concentration of the acids is greatest in the 200° to 230° fraction. Morgan and Soule find that in tar from the "Carbocoal" process, the 237° to 281° fraction has the highest acid content, whereas Davis and Parry find the 200° to 225° fraction of Freeport tar richest in phenols. Previous investigators have noted the following differences between primary and high-temperature tar: In the latter, naphthalene and anthracene occur in large quantities, the paraffins and naphthenes are negligible, the percentage of higher phenols is much lower than in primary tar, and the lower and more stable aromatic hydrocarbons have increased. In an endeavor to reconcile the change undergone when a primary is converted into a secondary tar, the writers have been unable to find references dealing with the extent of change which any one of the constituents of primary tar may undergo when subjected to secondary heating effects in the presence of other components, and the amount of the more stable compounds that may be expected from a given starting material.

Jan 1, 1932

Improve the Bureau-developed system for locating and communicating with miners trapped underground following a mine disaster. Approach Include in the wireless system a portable second-generation transceiver that is more reliable, compact, easier to deploy and operate, and ruggedized to withstand a mine environment. How It Works In an emergency, the new transceiver is snapped onto a caplamp battery for power. (Normally the 1 1/2-pound transceiver is either carried by the miner or is strategically located in the mine.) Its antenna wire, coiled inside the transceiver container, is removed and deployed in a roughly square configuration around a coal pillar or on the mine floor. The antenna consists of 300 feet of lightweight wire, which provides a large magnetic moment while remaining intrinsically safe, The photograph shows the

Jan 1, 1981

By John I. Kasteler, John H. Hild

"INTRODUCTION The South Hecla mine, one of the principal mines of the Alta United Mines Co., is situated at Alta in thee Little Cottonwood mining district, about 30 miles southeasterly from Salt Lake City, Utah. The mine has produced copper, lead, zinc, gold, and silver, and is reported to have been one 'of the principal sources of this country's bismuth from 1912 to 1925. The tungsten mineral, scheelite, has been found but has not been recovered. The extreme need for these minerals during World War II prompted an examination of the property by the Bureau of Mines and resulted in an unpublished report entitled ""The South Hecla Mine, Salt Lake County, Utah"" (fig. 1).A Bureau of Mines project 3301 was initiated, and operations were started early in 1943. The primary purpose of the project was to increase substantially the reserves of bismuth and tungsten ores. The critical situation in regard to lead, copper, and zinc developed during the early stages of the operation, and the work was expanded to include the development of ores 'of these metals.An investigation of 'the Albion, Rustler, and Greeley workings adjoining the South Hecla mine was made, and this work is also described (fig. 2); ACKNOWLEDGEMENTSIn Its program of investigation of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each investigative project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual investigative work, and prepares the final report. The Metallurgical Branch, O. C. Ralston, chief, analyzes samples and performs beneficiation tests."

Jan 1, 1948

By C. S. Compton, D. R. Dolinar, D. C. Oyler

More than 80% of U.S. roof bolts are fully-grouted, but about 1500 roof falls are reported each year. Anchorage failure of a fully grouted bolt can occur when the roof is active near the top of the hole. This paper reports on an extensive series of short-encapsulation pull tests (in which the bolts are installed with only 1 ft of resin) that were conducted in the National Institute for Occupational Safety and Health (NIOSH) Mine Safety Research Laboratory and operating mines in WV and PA. The tests confirmed that poor anchorage can been countered under some weak rock conditions. Suggestions for improving anchorage are included.

The United States has not begun commercial operations to tap its largest poten-tial sources of oil supply - oil shale and coal. The reason is that domestic petrol-eum has been plentiful in the past and liquid products probably could be produced from it at the lowest cost. In view of the ever-increasing need for petroleum in the United States, the critical international situation threatening foreign supplies, the growing demands for steel, and the heavy costs to industry of constantly discovering and developing new oil fields, it is believed that the prompt development of a synthetic fuel industry based on oil shale and coal is not only requisite to safeguard our oil supply but is an economically sound course for the foreseeable future. To neglect its development is to close our eyes and minds to our own resources at a time when they are needed critically. It also is apparent now that neither the Government nor industry would be taking any considerable economic risk in starting the initial plants, especially as measured against their potential value in meeting critical oil and chemical demands and in building a new industry in the West.

Jan 1, 1951

By Alexander Siefert, Steffen Pankoke

In the development of commercial vehicles as well as of passenger cars, the effects of vehicle vibrations on operating safety, health and comfort can only be predicted by numerical simulation when appropriate occupant models are available. Such models must be based on human anatomy and have dynamic properties of real humans in order to achieve realistic results. Since human dynamic behavior depend on posture and percentile, the occupant model needs to be adjustable to these parameters with respect to geometry and dynamic properties [1,2]. Dynamic Human Finite-Element-Model CASIMIR CASIMIR is a non-linear, dynamic finite-element-model of the human body. It consists of a dynamic model of the upper torso with head, neck, shoulders and arms as well as of a dynamic model of the lower extremity with pelvis and legs. The most important part is the lumbar area with dynamic non-linear models of the lumbar spine and of back and abdominal musculature. The frequency-dependent characteristics of the intervertebral discs and the effects of muscle activation and non-linear frequency-dependent muscle properties are included. In the latest stage of development, CASIMIR has been equipped with a compliant model of the body surface in the contact areas to the seat. This results in a very realistic transmission of static and vibrational forces into the human body, see fig. 1. Intense model verification and validation has been performed in all stages of model development, starting with validation of small components like intervertebral disc, ending with validation of whole-body-vibrations using measurements of the dynamic mass / mechanical impedance [4]. For an in-detail examination of stresses in the vertebral bodies and discs, a non-linear submodel of the lumbar spine with an increased number of degrees of freedom can be coupled to the whole-body-model, enabling the researcher to examine local effects of vibrations and single shocks on the lumbar materials. [ ] Since it is well known that human dynamic behavior is significantly affected by anthropometric data and posture, CASIMIR can be individualized to the anthropometric status of single individuals or to the mean values for specific percentile groups. Furthermore, posture can be adjusted to the seating conditions applicable to a specific vehicle. Posture modification capabilities include the variation of the lumbar lordosis [3].

Jan 6, 2006