Search Documents

By Victor Erickson

ECONOMIC recovery, which began in 1958, carried through into 1959 but was somewhat retarded by the 116-day steel strike beginning in July 1959. Recovery and economic growth increased production and consumption of mineral fuels 3 percent above 1958. The increase was accomplished despite a drop of 26 percent in coal exports. Prices remained constant during the year so that the value of production and consumption also increased 3 percent over 1958. Stocks in the hands of producers at yearend were little changed from the supply at the beginning of the year. Employment in the field of mineral fuels decreased 6.4 percent from 1958. Average hourly earnings were up 7 percent, and average hours worked were up 5 percent, with the result that weekly earnings gained 11.8 percent. Internal freight rates were relatively constant, but ocean tanker rates declined both in 1958 and 1959 from the high rates charged during the Suez crisis. The index of major input expenses decreased for anthracite, held constant for bituminous coal, and increased for petroleum. The index of labor cost per dollar of product and per ton of product declined again in 1959 to a new low in anthracite and bituminous-coal mining industries.

Jan 1, 1960

By Frank T. Greene

An investigation of the quenching behavior of coal dust-air flames was carried out. The literature relevant to coal dust-air flames was reviewed, including information on the agglomeration, sedimentation, and dispersal of dust clouds. The simple equations relating the various concentrations involved in dust flame propagation are given and their implications elaborated. It is shown that the concentration seen by a moving flame in a sedimenting dust cloud can differ significantly from the concentration commonly measured in such experiments. The known dust cloud phenomena which appeared significant in flame propagation studies were experimentally evaluated, and quenching diameters, flame speeds, and lean propagation limits for several tube diameters measured. For Pittsburgh seam coal, the Minimum Quenching Diameter (MQD) for dust between 10 and 20 µm was found to be between 0.7 and 0.8 cm, and the lean propagation for 3.2-cm tubes to be approximately 200 mg/liter. Similar MQD data were also obtained for Pocahontas and Sewell coals, Beulah lignite, and a 50-gal./ton oil shale. The effect of temperature, coal particle size, and propagation tube material were also investigated.

Jan 1, 1981

By G. W. Jones

Fires in anthracite refuse banks are troublesome and may become exceedingly costly to combat. Instances are known in which refuse-bank fires have grown to such magnitude that entire mining properties have been endangered. In one instance4/ a refuse-bank fire cost the mine management several hundred thousand dollars to extinguish. The exact number of fires formerly existing or now active in the anthracite region of Pennsylvania is not known. There are hundreds of anthracite refuse banks in this region, some very high and large in area, that have never caught firs, although a few are over 50 years old. This would indicate that spontaneous ignition of the material in these banks is improbable, a conclusion confirmed by recent laboratory research.

Jan 1, 1939

By G. W. Jones

Fires in anthracite refuse banks are troublesome and may become exceedingly costly to combat. Instances are known in which refuse-bank fires have grown to such magnitude that entire mining properties have been endangered. In one instance4/ a refuse-bank fire cost the mine management several hundred thousand dollars to extinguish. The exact number of fires formerly existing or now active in the anthracite region of Pennsylvania is not known, There are hundreds of anthracite refuse banks in this region, some very high and large in area, that have never caught fire, although a few are over 50 years old. This would indicate that spontaneous ignition of the material in these banks is improbable, a conclusion confirmed by recent laboratory research.

Jan 1, 1939

By Sean Gallagher, William S. Marras, Alan S. Litsky, Velimir Matkovic, Deborah Burr, John Landoll

Study Design. Survival analysis techniques were used to compare the fatigue failure responses of elderly motion segments to a middle-aged sample. Objectives. To compare fatigue life of a middle-aged sample of lumbosacral motion segments to a previously tested elderly cohort. An additional objective was to evaluate the influence of bone mineral content on cycles to failure. Summary of Background Data. A previous investiga¬tion evaluated fatigue failure responses of 36 elderly lumbosacral motion segments (average age, 81 ± 8 years) subjected to spinal loads estimated when lifting a 9-kg load in 3 torso flexion angles (0°, 22.5°, and 45°). Results demonstrated rapid fatigue failure with increased torso flexion; however, a key limitation of this study was the old age of the specimens. Methods. Each lumbosacral spine was dissected into 3 motion segments (L1-L2, L3-L4, and L5-S1). Motion segments within each spine were randomly assigned to a spinal loading condition corresponding to lifting 9 kg in 3 torso flexion angles (0°, 22.5°, or 45°). Motion segments were statically loaded and allowed to creep for 15 minutes, then cyclically loaded at 0.33 Hz. Fatigue life was taken as the number of cycles to failure (10 mm displacement after creep loading). Results. Compared with the older sample of spines, the middle-aged sample exhibited increased fatigue life (cycles to failure) in all the torso flexion conditions. Increased fatigue life of the middle-aged specimens was associated with the increased bone mineral content (BMC) in younger motion segments (mean ± SD, 30.7 11.1 g per motion segment vs. 27.8 ± 9.4 g). Increasing bone mineral content had a protective influence with each additional gram increasing survival times by approximately 12%. Conclusion. Younger motion segments survive considerably longer when exposed to similar spine loading conditions that simulate repetitive lifting in neutral and flexed torso postures, primarily associated with the increased bone mineral content possessed by younger motion segments. Cycles to failure of young specimens at 22.5° flexion were similar to that of older specimens at 0° flexion, and survivorship of young specimens at 45° flexion was similar to the older cohort at 22.5°. Key words: biomechanics, low back disorders, fatigue failure, age, motion segments, vertebral endplate fractures, torso flexion, lifting, bone mass. Low back disorders (LBDs) are a major cause of both short- and long-term occupational disability in the United States, and it is clear that workers in certain occupations are more susceptible to LBD.2-5 Specifically, epidemiologic studies have shown that jobs involving heavy physical demands such as construction,2,3 mining,2,4 and farming,5 engender increased risk of back pain. These occupations are thought to experience high LBD rates as a result of their extreme postural and manual lifting demands. Studies have shown that jobs involving significant lifting 6-9 and jobs that involve frequent bending10-12 are associated with increased LBD risk. Workers in the mining industry, in particular, often have to lift heavy materials in restricted workspaces that compel torso flexion. An understanding of the impact of repeated loading of the spine in flexion on fatigue failure of spinal tissues is thus a critical issue for our research agency, which is concerned with reducing the pain and disability associated with LBD in the mining industry. It is well accepted that loads experienced by the spine during manual lifting tasks are sufficient to cause fractures in the endplates of lumbar vertebrae, particularly on repeated loading. 13-15 Endplate fractures may not be painful in and of themselves 16; however, evidence suggests that the process of internal disc disruption and disc degeneration may be initiated via endplate fractures. 16,17 It has been shown that endplate damage will alter the distribution of stress in the disc, resulting in buckling of the lamellas of the internal anulus.17 Once this process has been initiated, repeated spine loading will cause additional disruption of the anular fibers, resulting in formation of significant fissures or tears. 11-21 If these tears occur near or extend close to the outer portions of the anulus, a wound healing process is initiated, which involves infiltration of mast cells, macrophages, and re¬lease of cytokines and growth factors. 21 The presence of these infiltrates has been strongly linked to discogenic low back pain. 21,22 Indeed, for patients experiencing chronic low back pain, the prevalence of internal disc disruption is at least 39%,19 which represents the most

By A. M. Ouchi

Existing empirical design tools have been developed from fair-to-good quality rock masses (RMR76 >50). This paper presents a focus of ground control research presently being conducted by the Rock Mechanics Group in the UBC Mining Department in incorporating weak rock masses (RMR76 <50) into existing empirical design relationships. An emphasis is being placed upon the updated span design curve/critical span graph originally developed at UBC. The original database has been augmented with over 450 weak rock data points from mines such as the Stillwater mine (Montana), the Eskay Creek Mine (BC) and several mines in the Carlin Trend and other parts of Nevada. The original database is comprised of spans supported with ?traditional? mechanical bolting. In weak rock environments however, this type of support has been found for the most part, ineffective. This paper presents the span and weak rock RMR76 relationship for four different support categories. This work attempts to provide rock mechanic tools that will enable a mine operator to make economic decisions that will also ensure a safe working environment.

Jan 1, 2008

By W. A. Calhoun

The purpose of this investigation was to develop economical mineral dressing processes for removing objectionable quantities of impurities, such as quartz and pyrite, from refractory clay deposits in east central Missouri. The presence of excessive quartz in these clays causes crazing. Pyrite causes bloating and unsightly dark blobs on the surface of fired refractory brick. The iron concentration in the proper state of oxidation may also act as nucleation centers for carbon crystal growth which can result in bursting of the refractory. Numerous deposits, representing a very large tonnage, have been examined and prospected by various refractories companies and found to contain impurities in objectionable quantities. Upgrading these clays would greatly extend our reserves of high-quality refractory clays. Wet-tabling and wet-cyclone concentration were found to be effective for removal of impurities from clays. Of the two methods, wet-cyclone concentra¬tion would be cheaper and more effective. Although wet-tabling improved the refractory properties of each clay, beneficiation by wet-cyclone produced clays of superior quality. Clay recoveries by wet-cycloning ranged from 56.1 to 81.8 percent of the weight of the crude samples, and the beneficiated clays contained from 71.9 to 94.4 percent of the total alumina. The pyrometric cone equivalent (PCE) was increased from 1 to 3 cones by wet-cycloning. The beneficiated clays also met the reheat shrinkage requirements on refiring to 1,400° C. Missouri is one of the major domestic sources of fare clay. In addition to deposits of high-grade refractory clays, there arc many deposits that contain small percentages of impurities, which render the clays unfit for the production of high-heat-duty firebrick. Development of methods to beneficiate these submarginal clays to usable materials would greatly increase commercial fire clay resources.

Jan 1, 1961

By Kenneth L. Cook

From March 1944 to July 1945 the Division of Geophysical Exploration of the Federal Bureau of Mines made magnetometer surveys of some of the principal iron ore deposits of the Iron Springs district, Iron County, Utah. The district comprises a belt about 23 miles long and 3 miles wide. Most of the large ore bodies are found as pods of replacement ore within a favorable limestone bed lying at the margins of three separate igneous intrusions in the district The magnetic surveys were confined chiefly to this geologically favorable zone at the margins. The iron ore is a mixture of magnetite and hematite. The magnetite content of the ore ranges from 14 to 58 percent. Magnetic anomalies of 1,250 gammas or more were usually found over the near-surface ore bodies. About 62,000 magnetometer stations were taken over a total traverse distance of about 300 miles. Outcropping ore bodies were surveyed to determine, insofar as was possible from the magnetic data, their probable length, width, depth, extent, strike, dip, and tonnage. Geologically favorable areas where no ore is exposed were explored in an endeavor to find new ore bodies. Favorable locations were determined for exploratory diamond drilling, both in areas of exposed ore bodies and in areas of newly discovered magnetic anomalies. Forty-five separate magnetic anomalies that indicate the possible existence of ore bodies were observed. Of these, 13 anomalies are caused by outcropping ore bodies of proved commercial size. Five are caused by non-outcropping ore bodies of proved commercial size which were discovered, in whole or in part, as a result of the geophysical surveys. Of the remaining anomalies, which lie in virtually un-tested areas where few or no ore bodies are exposed, six probably are caused by large, unexposed replacement ore bodies, nine are possibly caused by large, unexposed replacement ore bodies, and six are probably caused by unexposed magnetite veins of some small commercial importance,

Jan 1, 1949

By E. G. King

An earlier Bureau of Mines report4 provided low-temperature heat-capacity and entropy data for three sodium vanadates. This report continues the study of vanadates by presenting analogous data for three crystalline calcium vanadates - calcium metavanadate (CaV206), calcium pyrovanadate (Ca2V2O7), and calcium orthovanadate (Ca3V208). No similar data for these compounds have been published previously. MATERIALS All three vanadate samples were prepared by the Bureau of Mines by heating stoichiometric mixtures of reagent-grade calcium carbonate and vanadium pentoxide.5 Calcium metavanadate was prepared at 610° to 660° C. A stoichiometric mixture was heated for 17 days with intervening grindings, mixings, and adjustments of composition, as shown necessary by chemical analysis. The final analysis gave calcium oxide, 23.48 pct. (theoretical, 23.57 pct.) and vanadium pentoxide, 76.32 pct. (theoretical, 76.43 pct.). The sample also contained 0.11 pct. acid-insoluble matter. The X-ray diffracton pattern showed no lines of free calcium or vanadium oxides. No X-ray diffraction patterns were found in the literature for any of these substances.

Jan 1, 1961

By James D. Noll, Jon A. Hummer, Shawn E. Vanderslice, Aleksandar D. Bugarski, George H. Jr. Schnakenberg, Steven E. Mischler, Larry D. Patts

The National Institute for Occupational Safety and Health designed and conducted a study in an underground metal mine to assess the effects of selected diesel emissions control technologies on the concentrations of diesel particulate matter and gases in underground mine air. The control technologies studied included diesel particulate filter (DPF) systems, filtration system with disposable filter elements, diesel oxidation catalytic converter, and biodiesel blends. Each technology was tested on a mining vehicle operated in an isolated area of an underground mine supplied with fresh air. These isolated zone tests allowed for the operation of vehicles under conditions and over duty cycles that closely mimic actual duty cycles of production equipment. The DPF systems reduced the elemental carbon (EC) concentrations in mine air between 88% and 99%. The same systems reduced total particulate matter (TPM) concentrations in mine air by approximately 75%. The biodiesel blends B20 and B50 caused a reduction in the EC concentrations of 26% and 48%, respectively. Those blends also reduced TPM concentrations by 9% and 24%, respectively. The use of #1 diesel fuel reduced EC concentration by 13% compared to #2 diesel fuel. An increase in nitrogen dioxide concentration of up to two times was seen when platinum-catalyzed DPF systems were tested.

Jan 5, 2006

By James R. Boyle

The value of Alabama&apos;s nonfuel mineral production in 1984 was $409.8 million, and established a new record high for value of nonfuel minerals in the State, at 13.4:% over the previous high of 1983. Output of nearly all nonfuel minerals increased; phosphate rock was one of the exceptions, with no recorded output in 1984. Cement, crushed stone, lime, sand and gravel, and clays were the major commodities produced in Alabama. Alabama led the Nation in the production of crushed marble; was second in bauxite; third in fire clay and kaolin; fourth in bentonite, ferroalloys, and dimension marble; fifth in masonry cement, lime, and recovered sulfur; and sixth in portland cement. Alabama ranked 22d in the Nation in value of nonfuel minerals produced.

Jan 1, 1986

By L. A. Haas

A kinetic study of the carbon deposition reaction was undertaken by the Bureau of Mines as part of a broad investigation of metallurgical reactions in the iron ore blast furnace. The disproportionation of carbon monoxide on iron pellets was investigated at carbon monoxide pressures between 0.5 and 2 atmospheres (absolute) and temperatures from 400° to 1,075° C. Gas flow in the range from 0.25 to 0.85 standard liter per minute was found to have little effect on the reaction velocity. The addition of nitrogen and helium to caron monoxide exerted only a dilution effect on the rate of carbon deposition. However, an addition of 1 percent hydrogen increased the rate about 100 times. Small amounts of carbon dioxide in the inlet gas exerted little effect on the rate of carbon deposition. The maximum rate for carbon deposition in the first 2 hours occurred at 550° C. The apparent molar activation energies at various stages of the reaction were found to vary from 13 kcal initially to 36 kcal during the latter stages of the reaction. The reaction rate behavior was tentatively explained by an adsorption step followed by the diffusion of iron through a shell of inactive iron carbide.

Jan 1, 1968

This report presents the results of a study for the Bureau of Mines to compare loan terms for non-fuel mineral projects in developing countries, from various International Financial Institutions (IFIs), and from private sector commercial sources. The study compares IFI and commercial loan terms for seven mineral projects in developing countries. The International Financial Institutions represented are: ? International Bank for Reconstruction and Development (World Bank) ? International Finance Corporation (IFC) ? Inter-American Development Bank (IDB) ? Asian Development Bank (ADB) ? International Monetary Fund (IMF) In addition, the costs of financing for these mineral projects were compared with the costs of long-term debt to the five largest U.S. mineral producers.

Jan 1, 1986

By Harry W. Campbell

A mineral survey conducted by the U.S. Bureau of Mines in 1983 identified no mineral resources in the Beaver Meadows, Blind Horse Creek, Chute Mountain, Deep Creek/Battle Creek, and North Fork of Sun River Wilderness Study Areas (WSA&apos;s). A prospect east of the Beaver Meadows WSA has low potential for lead resources. Sand, gravel, and limestone occurrences are numerous in the WSA&apos;s; however, similar or better quality materials outside the areas are abundant and more accessible to potential markets. Impure coal and titaniferous-magnetite occurrences are near the WSA&apos;s, but are not known to occur within these areas. In 1983, there were 7,025 acres leased for oil and gas within the five WSA&apos;s; no current mining claims were in or near any of the WSA&apos;s. Evidence of mining activity was found at only one prospect in the WSA&apos;s. It is inside the Deep Creek/Battle Creek WSA; no resources or resource potential were identified at this prospect.

Jan 1, 1984

During the initial portion of the contract several alternative designs were considered, as set out step by step in the monthly reports. The conclusions reached during this period were - to use on INTERDATA Model 70 as the system minicomputer - to drop the idea of multiplexing and digitizing the inclinometer outputs downhole due to the greater complexity and cost that that alternative would imply - to use a multitasking software monitor to enable synchronization of the several tasks that the system would have to perform simultaneously - to use a common controller for all I/0 devices except those which were available off the shelf from Interdata - to use a sheave counter to meter off equal increments of probe travel, but to supplement this information with the use of an encoder on the winch drum in order to be able to measure total probe travel unambiguously. - to place all I10 device interfaces in a bin connected to the common controller. During this period considerable attention was dedicated to the design of the mechanical components contemplated it the original contract. Of these, only those required for vertical probe was complete at the time that it was decided to forego the mechanical subsystem and concentrate on developing the necessary electronics and software to interface with the probes being developed by the Bureau of Mines.

Jan 1, 2012

By Donald L. Siebert

This profile study of the commercial secondary aluminum industry examines not only the elements that form the industry but also the technological contributions of each toward industrial growth. Concise descriptions of processing methods trace aluminum scrap from generating sources to marketable industrial and consumer goods. Economic and marketing appraisals are used to illustrate the impact that recent technology has had upon the secondary aluminum industry. Price, supply, demand, competition, and substitutes are selected as components of an economic model of the secondary industry and are used to illustrate the aggregate effects of technological changes. The final section is a conceptual look at the future in which sensitive economic indicators (such as die casting in the automotive and appliance industries) are examined as well as the problems of conserving mineral resources by retrieving secondary aluminum from solid waste.

Jan 1, 1970

By R. V. Petrella

The flash induced combustion of Sewell and Pittsburgh coals was studied in air and in oxygen. The primary decomposition and combustion processes occur within the first 300 ~sec in oxygen and slightly later in air. Strong absorption spectra of CN and OH are indicative of the decomposition and combustion processes, respectively. Kinetic spectroscopy and combustion product analyses indicate that only about 35% of the coal dust is consumed in the explosive combustion which takes place in several (1-5) distinct but similar steps. The combustion-modifying effects of (NH4)2HP04, NH4H2P04, KHC03 and Rock Dust were studied in the 1-20 wt % range in coal dust flash com-busted in air and oxygen. The study reported herein shows Rock Dust to be the most efficient coal combustion inhibitor. KHC03 is the least effective agent, with the phosphate salts showing marginal effectiveness.

Jan 1, 1976

By R. F. Selden

The material in this paper is intended simply, to be an inquiry into some of the theoretical aspects of the occurrence of methane and carbon dioxide in coal, with a brief resume of the more recent literature. Several discussions on various phases of the subject have been published, a few of which (4, 20, 25, 88, 90)4/ have more or less extensive bibliographies of tie earlier literature. In large measure the pertinent literature deals with the unusual aspects of the subject, and in consequence it might appear that the normal aspects have not been given due consideration here. The latter information is largely a matter of practical field experience, and since that which is normal to one locality is often abnormal to another no sharp differentiation appears to be necessary or, in fact, possible. No attempt will be made to present a critical discussion of the relations between the presence of gases in coal and pertinent geologic features or mining practice. Although the presence of foreign gases in the ventilating air of many mines is not particularly noticeable, in many others the evolution of methane and perhaps small amounts of carbon dioxide (or sometimes the reverse - large amounts of carbon. dioxide with perhaps sore methane) is quite apparent.

Jan 1, 1934

By Gregory Molinda

NIOSH has recently completed a study of the interaction between polyurethane (PUR) and coal mine roof in order to determine the mechanism of reinforcement, in both highly fractured rock and unfractured rock. Four case studies of PUR rein­forcement are presented. At a West Virginia site, a borehole camera revealed the location of roof voids and guided the PUR injection. By injecting polyure­thane into a zone from 0.6 to 1.8 m (2?6 ft.) high in the roof, a roof beam was created and ongoing intersection falls were halted. In another highly fractured roof in a western Pennsylvania mine, a total of 5.8 cm (2.3 in.) of rubbleized rock was found in a zone up to 3 m (10 ft.) into the roof. Untargeted PUR injection filled approximately 1/2 of the fractures. These two case studies showed that it is not necessary to fill up 100% of the void space to create stability. In the other two field sites, polyurethane was injected into weak, but unfractured roof. Post-injec­tion video monitoring showed that weak bedding planes were hydraulically wedged open and polyure­thane injected along bedding. The reinforcement value of this injection method is limited because of the wafer-thin layer of PUR introduced along bedding, and the lack of a PUR ??webbing?? which would serve as a structural framework to provide strength. It was determined that video inspection prior to PUR injection can aid in identifying the fracture zones to target, and minimize ??blind?? pumping and loss of PUR.

Jan 1, 2008

By Larry L. Wischhoefer

The Automated Breathing Metabolic Simulator (ABMS) is a versatile machine capable of performing almost any physiologically appropriate respiratory simulation. The first ABMS was delivered to the Bureau of Mines by IBM in 1973. Since then efforts have been made to refine the systems and components which make up the ABMS including the Breathing Simulator Module (BSM), Gas Analysis Module (GAM), and Supervisory Controller (SC)-each of which are also capable of stand-alone operation. Since September 1980, Reimers Consultants has been testing and modifying the ABMS and its components in order to improve the equipment and to develop simulation criteria and parameters. Changes have been made to the Phase I Design Plan and Performance Specifications; future improvements based on current experience are recommended; and test results of full scale testing conducted by Reimers Consultants in November 1983 on several types of breathing apparatus are reported and illustrated.

Jan 1, 1984