Search Documents

By Donald Koch

The project investigated regional impacts of mining on the ground water system of the Powder River Basin by: 1) establishment of a regional ground water monitoring network, and 2)development of , set of digital computer models to simulate ground water flow and quality, ground water contributions to surface water flow and quality (i.e., baseflow), and watershed run-off and recharge. Over 100 wells were monitored for physical and chemical parameters. Data were used as input to the model; and for the development of a comprehensive data base. The basin was modeled on a regional and subregional scale using a finite -difference model employing an alternating difference technique. Two water-shed models were evaluated for their ability to provide runoff and recharge inputs to the basic ground water model. Application of the regional and subregional models using conservative mining scenarios showed that drawdowns may extend west from the mines as far as ten miles but that impacts would be insignificant on a regional scale. The watershed model could be effectively applied to small watersheds only.

Jan 1, 1982

By Andrew K. C. Wong

Hydraulic transport has been considered as one of the most economical methods in transferring granular materials over relatively long distances. In the natural world, it is used to transport basic material required for the support of life; in industry, it is a method widely adopted for handling materials. But the phenomena of hydraulic transport has not yet been thoroughly understood. As most of them are conditioned by a number of hydraulic and mechanical parameters, of which the basic relationships are not fully known, the traditional approach in relating these parameters to the energy requirement is purely empirical in nature. Empirical formulas, such as that proposed by Durand, (1) only give satisfactory results over a selected range of (particle size)/(pipe diameter) ratios and slurry concentration. When the case is more complicated or when new situations arise, the empirical formulas fail to give good predictory results. In fact, most of these formulas are based upon dimensional analysis, where the underlying physical interaction is not explicitly considered. Apart from the loosely related, non-dimensional groups incorporated in the formulas, there is practically no analytical means for modifying the formula so as to enable it to cope with more complex real physical situations. Although it seems quite remote that a complete rigorous solution to this highly complex problem could be generated in the near future, it is generally recognized (2, 3) that research in this area should be directed to more comprehensive studies of the obscure phenomena. In fact, there are a good number of very basic problems such as the effects of gradation and concentration of particles upon

Jan 1, 1972

By R. B. Stotelmeyer

Mineral resources, or a potential for their discovery, occur at 34 localities in the Glacier Peak Wilderness and adjacent areas of the north Cascade Range of Washington (see plate). Eighteen of the mineral deposits are in the established Wilderness, four are in or partly in contiguous RARE II (Roadless Area Review and Evaluation) lands recommended by the Forest Service for addition to the Wilderness (A, D and G6031.), three are in adjacent RARE II lands excluded from wilderness consideration, and nine are in nearby roaded areas excluded from the RARE II inventory. Mineral commodities that might be produced from the Wilderness and recommended additions are gold, silver, copper, lead, zinc, molybdenum, arsenic, cadmium, tungsten, cobalt, limestone (marble), pumice, and volcanic cinders. Mineral production from adjacent lands might include most of these commodities, plus antimony, decorative stone, pyrite, silica, and garnet.

Jan 1, 1982

By C. F. McCarroll

The effectiveness of an industry's safety activities can be gaged best by the accident records of that industry. In an effort to gage conditions in the petroleum industry, and with the objective of helping to reduce the number of accidents in it, the Bureau of Mines from time to time has tabulated, analyzed, and published pertinent statistical information.3/. These reports have dealt with distribution, causes, and costs and related phases of accidents for various and collective divisions of the petroleum industry in several sections of the country. This type of study aids the personnel of the Bureau in planning the course of its activities in accident-prevention work and gives useful data to persons engaged or interested in the promotion of safety in the petroleum industry, which will aid them in their efforts to reduce the number and severity of accidents. A majority of petroleum operators and "service? contractors have acknowledged their responsibility to provide their employees with safe working conditions and to their stockholders for greater economic value of invested capital by establishing safety divisions within their respective organizations. Such divisions have a primary duty, namely, to see that properly designed and guarded machinery and working equipment are furnished the employees and that they are trained in the safest practical methods of performing their work. Some companies and individual operators, however, have shown little or

Jan 1, 1939

By Thomas E. Finch

This report is a continuation and expansion of a previous USBM grant (No. G0254004) which examined alternative methods of handling the parting between two coal seams in a surface mining operation. The alternative methods consist of equipment implementation in either a stowing or haulback technique. Following a typical strip mine conformation, the parting is directly stowed or hauled back and placed in the pit bottom after second seam removal. The objectives are to produce an environmentally sound material placement technique and to increase prime stripping machine utilization. This report contains the engineering philosophy behind two computer programs created to evaluate parting handling methods over d wide range of coal and parting thickness ratios. The nature of the computer approach allows cost sensitivity analysis and quick updating of costs. The two programs are clearly presented with documentation and examples such that consumers may apply then to their own operations.

Jan 1, 1977

By M. P. Board, J. K. Whyatt, T. J. Williams

The U.S. Bureau of Mines has been conducting a series of rock mechanics investigations at the Lucky Friday Mime in the Coeur d'Alene Mining District of northern Idaho. In the present study, the energy release rate (ERR) index was used to evaluate three underhand stope backfill parameters--cement content, density, and placement gap-to determine their influence on rock bursts. This index provides a relative measure of the likelihood of rock bursting for a given rock mass. It is known that the elastic idealization of the rock mass inherent in this method causes underestimation of stope closure and hence underestimation of the influence of backfill on rock bursting. However, this evaluation still showed that (1) changing from present practice to one in which backfill was omitted altogether would increase the ERR by 42 pct and (2) perfect placement of backfill would reduce the ERR below present practice levels by 28 pct. The easiest step toward perfect placement would be elimination of the placement gap, which accounted for half of the difference in ERR between present practice and ideal placement conditions. There was no indication that increasing initial fill strength through increased cement content would affect the ERR.

Jan 1, 1992

By K-H. Frohne

This report presents a study of the Cooper sand of the Fork Run pool of Warren and McKean Counties, Pa., and a prediction of the secondary oil recovery by gasflooding the reservoir. A computer program employing a modification of the Craig, Geffen, and Morse secondary recovery calculation was used to make the gas flood performance forecast and is presented in the appendix. The Cooper sand reservoir in the Fork Run pool lies at a depth of about 1,900 feet and covers an area 1/2 mile wide by 2-1/4 miles long. Original oil in place is estimated to have been 8,266,000 STB. The primary recovery mechanism is solution gas drive, and ultimate primary recovery may reach 20 percent over a well life of 90 years. Two computer predictions were made for gas flooding the Cooper reservoir. The first was for a 25-acre pilot five-spot utilizing existing wells, but project economics were poor since only 25 percent of injection gas is utilized for pilot oil recovery. Recovery was 71,000 STB, or 22 percent of oil in place at flood initiation, but required 25,700 scf gas injected per STB of oil recovered. In the second prediction, pilot area performance was projected for the entire Fork Run pool, and economics became good. Recovery was 1,753,000 STB from 25 five-spots after the injection of only 6,400 scf per STB of oil recovered.

Jan 1, 1969

By Loren R. Anderson

A probabilistic slope stability computer model was developed at Utah State University and independently evaluated by CH2M Hill Consulting Engineers as a design and analysis tool. Volume I of this report describes the model and Volumes III and IV are users manuals for the computer programs. This volume (Volume II) constitutes the report by the CH2M Hill. It includes a description of a field investigation and stability analysis of an existing tailings dam. Based on the results of the analysis, the tailings dam was evaluated for redesign using probabilistic considerations. Conclusions are made regarding the usefulness of the model as a design tool.

Jan 1, 1982

By R. E. Zane

[The Northwest Experiment Station of the Bureau of lines, in cooperation with the College of Mines, University of Washington, has completed a detailed investigation of the physical and chemical properties of western cokes made or used in the Pacific Northwest, as evaluated by standard methods. 4/ One of the chemical properties determined, to which more or less importance has been attached, was reactivity or combustibility. As no standardized procedure is available, it was necessary to develop a workable method for evaluating this property. The combustibility of coke is usually measured by the formation of carbon dioxide with time at a particular temperature or by the reduction of carbon dioxide to carbon monoxide. Analysis of the resulting gases commonly is required to evaluate the result. The method described in this paper is simple and direct in that the sample of coke or other carbonaceous material is weighed as it burns; the loss in weight and time is indicated by a balance and clock arrangement. Gas analyses are not rewired. Methods similar in principle have been used by Tu, Davis, and Hottel6/ and by Oshima and Fukuda7/ for determining the combustion rate of carbon and for studying the effect of ash on combustion characteristics. Both methods: are more elaborate in procedure and apparatus required than teat described here. Brief the method comprises burning a sample of coarsely grained. coke or]

Jan 1, 1940

U.S. Gold Commission Established. - The President, with the authorization of Congress, has named a gold commission made up of 17 individuals, most of them Government officials, to study U.S. policies related to the role of gold in domestic and international monetary systems and report its findings and recommendations to Congress. U.S. Lead Exposure Ruling. - On June 29, the Supreme Court upheld the Government's right to set lead exposure levels for employees at the workplace. The Court ruled in favor of the Occupational Safety and Health Administration (OSHA) in a challenge by a group that alleged that OSHA had failed to conduct a cost-benefit analysis prior to issuance of the lead standards. It was the Court's contention that Congress did not require such an analysis when it empowered OSHA to establish workplace standards. The petition to the Court was made by the Lead Industries Association Inc., Battery Council International Inc" American Iron and Steel Institute, St. Joe Minerals Corp., and other lead mining and consuming firms.

Jan 1, 1981

The objective of this study was two-fold: 1. To perform a world literature search pertinent to the analysis, selection and design of hoisting systems and their components and to codify the search into a literature compendium. The search resulted in a technical data file of over 1500 hard copy items. The compendium index was also suitable for establishing a comprehensive computer-loaded data base on the subject. 2. To develop a comprehensive system of guidelines to cover salient aspects of analysis, selection and design of electrical, mechanical and structural components of a hoisting system with a view to establish parameters for maximum safety and efficiency of operation, installation and revision of the system. 3. (a) The system design of hydrostatic drives for mine hoists, usually of special nature, is considered along with oil hydraulic component selection suitable for the application; (b) The criteria for head frames of steel and/or concrete are developed with full consideration of all operating and environmental conditions.

Jan 1, 1988

By Sam S. Taylor

[The discovery of many oil fields in Illinois since 1936, and their rapid development have brought the problem of brine disposal to the foreground in that State. The ultimate magnitude of the problem is not yet known, but already it is treat enough to warrant technical investigation. The Bureau of Mines, therefore, has made a general survey of the methods of handling oil-field b brines in Illinois rend has studied in detail three subsurface disposal systems.]

Jan 1, 1940

By Clarence O. Babcock

Model pillars of limestone, marble, sandstone, and granite with length-to-diameter (L/D) ratios of 3, 2, 1, 0.5, and 0.25 (0.286 for granite) were tested to failure in axial compression to determine to what extent an increase in end constraint increased compressive strength. Adjustable steel rings, mechanically tightened about the ends of test specimens to create a radial prestress of 3,000 or 5,000 psi prior to the application of axial load, increased end constraint more than was possible in previous tests using solid steel rings. (Solid rings, epoxy-bonded to the ends of dogbone specimens, increased compressive strength compared with that of straight specimens without ring constraint.) During the loading cycle, additional end constraint was produced by lateral expansion of the specimens against the rings. The effect of the end constraint was to increase the compressive strength 55 to 58 percent for the shorter pillars of dogbone shape compared with the compressive strength of straight pillars with the same L/D ratios without ring constraint. Most pillars with L/D ratios of less than 2 were made stronger by end constraint. Pillars with an L/D ratio of 3 did not benefit significantly from end constraint. When the results from compression testing of straight specimens of rock in the laboratory are used to design mine pillars in situ, the pillars will be larger than necessary if the horizontal compressive stress is several thousand pounds per square inch greater than that resulting from the weight of the overlying rock alone. The L/D ratio can be increased by a factor of 1.76 for ratios in the range 0.25 to 3 and still provide the same compressive strength. The safety factor applied with straight specimen test results should also be acceptable for use with constrained pillar test results.

Jan 1, 1969

Electrical trailing cable used to power coal mining machinery is frequently damaged by tensile strain or crushing by mining machines running over the cable. A major problem is finding the exact location of a short or open in this cable so it may be repaired. A major problem is finding the exact location of a short or open in this cable so it may be repaired. FMC Corporation was awarded modification III to USBM Contract H0122011 to continue development and testing of cable fault locators, resulting in delivery of: 1. A prototype electrostatic/electromagnetic/ TDR transmitter and an electrostatic/electro-magnetic receiver sot that: o Locates cable faults by time domain reflectometry o Locates opens by detecting electrostatic signals o Locates shorts by electromagnetic coupling. 2. A prototype infrared detector and an infrared detector power supply that heats a shorted area by applying high current (at low voltage) and locating a short by infrared output. 3. Twelve production infrared detectors. 4. Detail drawings for all of the developed instruments.

Jan 1, 1973

By N. I. Jayaraman

High-pressure shrouded sprays were first tested on a bench to determine air-moving capability and dust collection efficiency. The bench-scale tests indicated that at 500 psi and above, the dust collection efficiency, when sampled downstream of a water eliminator, was about 99 pet for two types of nozzles. However, for the same water flow, the induced airflow was about three times greater in one type than in another. Since the only difference in the nozzles was the spray angle, this factor was important in air movement through a shrouded spray. Full-scale model mine tests were then conducted to determine the reduction in dust concentration behind the line curtain and at the operator position produced by high-pressure sprays in a shroud. The shroud was mounted on top of the boom of a model continuous miner, and high-pressure (greater than 500 psi) sprays were installed inside the shroud. The inlet of dusty air to the shroud was open toward the face and the outlet toward the exhaust line curtain. The high-pressure sprays were compared with conventional sprays mounted at the head of the continuous miner and directing water toward the face. The difference at the operator position (opposite side of brattice) was significant in that, under certain conditions, with conventional sprays an increase in respirable dust concentration of 471 pet was noticed compared with dry operation due to rollback from face. High-pressure shrouded sprays, on the other hand, decreased the dust concentrations at the operator position (opposite side of brattice) by 28.2 pct.

Jan 1, 1981

By Sean Gallagher, John R. Bartels, Dean H. Ambrose

Remote operation of continuous miners has enhanced the health and safety of underground miners in many respects; however, numerous fatal and non-fatal continuous miner struck-by accidents have occurred when using remote controls. In an effort to prevent these injuries, NIOSH researchers at Pittsburgh Research Laboratory examined the workplace relationships between continuous miner operators and various tramming modes of the equipment using motion captured data, predicted operator response times, and field- of- view data to determine causes of operator-machine struck-by events in a virtual mine environment. Factors studied included machine speed, direction of escape, operator facing orientation relative to the machine, work posture, distance from machine, and operator anthropometry. Close proximity to the machine, high machine tramming speeds, a right-facing orientation and operator positioning near the tail all resulted in high risk of being struck. It is hoped that this data will provide an improved rationale for operator positioning for remotely operated continuous miners.

By Ralph B. Stevens

The objective of this 20-month program was to define the relationships between mine ventilation, temperature, humidity, ore properties, material's used in mine operations, etc., and the spontaneous combustion problem in underground metal mines. Tradeoff studies of availability, reliability, cost, and maintenance of spontaneous combustion protection sensors and telemetry were conducted, after which a prototype system was selected from four design alternatives. This selected system was then laboratory tested and demonstrated in an underground copper mine.

Jan 1, 1979

By Warren E. Morrison

INCREASED production and utilization of minerals fuels and power accompanied the overall expansion in U.S. economic activity during 1963, which saw continued advances toward higher production, employment, and purchasing power. During 1963, record levels of wages, profits, and consumption were attained, while costs and prices maintained the stability exhibited throughout most of the recovery period. Expanding industrial production, the average index of which went from 118.3 in 1962 to 124.3 in 1963, narrowed the gap of unused manufacturing capacity to an estimated 5 percent. Gross national product (GNP), another major indicator of economic activity, reached a record level of $583.9 million (current dollars) during the year, this being $27.7 billion, or 4.9 percent above 1962. These achievements were somewhat marred by unemployment, which remained at 5.5 percent of the labor force in 1963, and the continued deficit in the U.S. balance of payments. Against this general background, total national consumption of energy resources for the year was equivalent to 49,816 trillion British thermal units (Btu), an increase of 4.2 percent over 1962. This represented a somewhat lower rate of growth than for GNP during the year.

Jan 1, 1964

By Donna L. Anderson

This U.S. Bureau of Mines report describes a system to determine the position and heading of a continuous mining machine during the maneuvers required at the face area of a mine. The system consists of commercially available angular position sensors and a computer interface developed and tested at the Bureau. The sensors employed are laser-based scanning devices that report the angular location of retroreflective targets within their 90° field-of-view. The targets are mounted on the continuous mining machine; the laser scanners are mounted on an external reference structure. The computer interface consists of a single-board computer-controller programmed to gather and process the angular position information, and to calculate the machine's position and heading relative to the reference structure. A sensor fusion algorithm will be incorporated into the computer interface programming to increase the accuracy and reliability of the system.

Jan 1, 1989

By Michael S. Miller

In 1984, at the request of Bureau of Land Management, the Bureau of Mines studied 8,500 acres of the 20,250-acre Seven Blackfoot Wilderness Study Area (WSA) consisting of all 3,950 acres of MT-024-657A and 4,550 acres of the 4,850 acre MT-024-657B in order to evaluate the mineral resources. Within this report these 8,500 acres are referred to as the study area. Located about 30 miles northwest of Jordan, MT, the study area is underlain by outcrops of Quaternary alluvium and Cretaceous to Paleocene sandstones, shales, clays, and coal. No mines or prospects were found in the study area. Except for some current interest in petroleum and natural gas, there has been no mineral exploration activity in the study area. The study area contains subeconomic clay, placer gold, and coal. Land within the study area is leased or under lease application for oil and gas.

Jan 1, 1986