Search Documents

By Stephen Mansfield

In metalliferous mining operations, subdrill is that portion of the blast hole that is drilled below the target grade elevation, and in most cases loaded with explosives. Its primary aim is to enable efficient excavation down to the target floor level. Subdrill is often described as being expensive and that excessive subdrill should be avoided, as it can result in damage to the subsequent floor, lead to difficult drilling conditions and higher vibration levels. As a result, many operations aim to apply the bare minimum amount of subdrill in order to excavate to the target floor

Feb 1, 2020

By Lon Santis

This paper analyzes 110 serious accidents that occurred during the use of commercial explosives in mining, construction, and other industries since 1992. Data from the Mine Safety and Health Administration (MSHA), the Institute of Makers of Explosives (IME) members’ reports, and media reports were used. Only accidents that resulted in a fatality, significant lost work time, or injury to the public were considered in this analysis. The accident data were analyzed for trends in frequency, type of industry, cause, type of individual harmed, and geographical region. Although the data showed that explosives accidents are decreasing in frequency, still, 29 people were killed and 134 injured. Eightyfive of the accidents occurred in mining, 17 occurred in construction, and 8 occurred in other industries including oil recovery, seismic exploration, agriculture, logging, boiler cleaning, and avalanche blasting. As other studies have shown, flyrock and failure of blast area security caused over half of the accidents. Mishandling, misfires, or fumes caused just over one-third of the accidents. Lightning and drilling into explosives were responsible for the remainder of accidents.

Jan 1, 2003

By Luan Monteiro, Francisco Biulchi

The AngloGold Ashanti - Cuiaba mine sought innovative approaches to minimize lateral development and stope extraction time while maintaining optimal gold recovery and minimizing dilution. The stope 8GAL EXT 30 was selected as a case study. Traditionally, conventional blasting methods in such a scenario would necessitate either a single mass blast or slot development at each end of the stope. These methods typically compromise recovery and dilution or increase development time and risk. Additionally, conventional wired detonators require workers to re-enter the stope between blasts to load blastholes and connect detonators. The wireless initiation system offers a solution by initiating blastholes using magnetic induction signals that can penetrate rock, air, and water. This technology allows a pre-charged stope to be mined without requiring workers to re-enter the area between blasts to charge and connect blastholes. Engineers from Orica and AngloGold Ashanti designed a new extraction sequence utilizing the wireless initiation system. The process began with the opening of one end of the stope using a conventional slot and wired electronic detonators. Subsequently, pre-loaded rings were fired in three blasts to extract the opposite end and the intersection. The 8GAL EXT 30 stope was successfully mined using this technology enabled method. Each blast was meticulously monitored, and the stope void was scanned to assess blast performance. The results demonstrated a 4.6% improvement in recovery and a 16% reduction in dilution compared to the initial plan, and reduced exposure of people to hazardous locations in the stope. These results represent an additional value of USD 200k, gained from implementing wireless initiation to enable this particular blasting schedule.

Jan 21, 2025

By August Ferraz Ribeiro, Guilherme Dias Mendona, Paula Henrique Lisboa, José Silvio Corsini

Correct slope adhesion is related to the conformity of the slope’s real geometry to slope planning. It is very important in mining because slope design has economic and safety implications. Slope design conditions can interfere with mining waste and ore proportion. Without a correct wall, the development of the mine can be hindered, which can reduce the amount of ore available. Furthermore, correct slope design reduces the possibility of melting and allows traffic with equipment and people in the mine. However, defining the wall is a more complex work as the characteristics of the rock require the use of blasting techniques. Therefore, Enaex Mining Technical Solutions (EMTS), in partnership with the engineering team at the Chapada Mine, at Lundin Mining, has developed this study in order to increase slope adhesion. The basis of this study is a near-field vibration test, which enables the creation of vibration attenuation law, and a seed wave damage model has allowed the characterization of the rock present at the Chapada Mine. Then, we could compare the model result to the real slope adhesion achieved with the buffer technique used in the mine. Therefore, it was possible to relate the real result to the model result.

Feb 6, 2023

By Mark Svinkin

To save time for construction of coal pits, the contractor decided to combine erection of the tower pitheads with digging of skip shafts to the depth necessary for placing proper coal pit equipment. It was obvious that blasts used in shaft faces and lifting machines installed at a lower part of the pithead could excite vibrations of an upper part of the pithead with curing concrete. The contractor was concerned about vibrations of pithead concrete structures and the disturbance of freshly poured concrete in forms at a top of the pithead as a consequence of structure vibrations. The results of a study of the tower pithead structure vibrations from blasting and operating machinery, and effects of structural vibrations on curing concrete are presented. Structural vibrations were measured at the tower pitheads of two coal pits from twelve blasts. Records of horizontal and vertical displacements were superposition of harmonic low-frequency damped vibrations and sporadic high-frequency damped vibrations with a variable frequency. Low frequency vibrations attenuated during 8-13 s after the last delayed blast. Measured values of the natural frequencies of pithead horizontal vibrations coincided with the calculated frequencies of horizontal bend vibrations. An increase of a face depth from 18 to 50 m diminished 16 times horizontal bending vibration displacements of concrete structures. Measurements of vertical structural vibrations from blasting demonstrated increasing of vertical pithead displacements with the rising of structure elevations. This is evidence of the pithead longitudinal tension. The holes with charges were not properly condensed for one blast. As a result of incompact stemming, the blast substantially increased the energy of airborne pressure waves, which triggered natural vertical vibrations of the pithead with high displacements.

Jan 1, 2004

By A. Ravi Kumar

A trench is a structure to accommodate fluid carrying pipelines for water, gas, petroleum products etc. Trench serves the purpose to haul the fluids in bulk over long distances safely and economically. Use of pipeline for moving oil and gas was essentially a post World War II development, but now it has acquired its own importance.

Jan 1, 2008

By Sven-Erik Johansson, Gosta Rundqvist, Donald Jonson

In Stockholm a new road traffic system called Södra Länken (Southern Link) will be in operation in late 2004. The total length of the road system is 6 kilometres of which 4,5 kilometres run through tunnels under suburbs immediately south of Stockholm inner City. The new traffic tunnels together with existing Metro tunnels, which mostly are in rock, will be the determining factor for blast design for many projects in the future. To set reasonable and safe permitted vibration levels the Swedish National Road Administration, Stockholm Region and Stockholm Transport Rail System have together financed a project to determine guide levels for blast-induced vibrations in traffic tunnels in rock. The purpose of the project has been to establish guide levels that are appropriate for different types of rock tunnels.

Jan 1, 2004

By John Horgan, Ethan Marcoux

Explosives have been used to demolish many unsafe structures around the world. However, it is unlikely any demolition job has ever involved destroying buildings already buried 40 feet (12 meters) into the world’s largest ice sheet. That is what happened to the original research station at the geographic South Pole, built back in the 1950s, following a series of discrete explosions between 2011 and 2013.

Jan 1, 2015

By Raden Haris Handayana, Jihan Farhan Lubis, Milia Putri, Tengku Deli Hamonangan Hasibuan, Sani Salahudin

An environmental issue that must be controlled from coal overburden blasting near the structure is ground vibration. Damaging ground vibration is the effect exerted from residual energy from blasting that does not work to fracture the rocks. Sebuku Tanjung Coal is a coal mining that operates T3 Pit adjacent to the High Voltage Tower. This structure is included in the Class 5 building with a maximum Peak Particle Velocity (PPV) of 40 mm/s. The shortest distance from the blasting location to the structure is 105 m. The initiation system used is electronic detonators combinate with emulsion as an explosives type. In Indonesia, the government regulated vibration limitation on SNI 7571:2010. The blast outcomes targeted are PPV below 40 mm/s, fragmentation size <80 cm for Excavator Komatsu PC-2000, and digging time <12 seconds. In this paper, the blast design was engineered by conducting Signature Hole Analysis for optimizing delay timing configuration and Scale Distance regression analysis to determine optimum charge weight per delay at the blast site. PPV results from 30 blastings achieved 100% below 40 mm/s with the range of about 1.773-30.250 mm/s. The deviation between PPV prediction to PPV actual is less than ±18% which provides the blasting with electronic detonator resulting in good PPV prediction for controlling vibration. The average fragmentation size (D80) is 55.81 cm in the 1st layer and 54.81 cm in the 2nd layer. The average digging time is 10.30 seconds in the 1st layer and 10.12 seconds in the 2nd layer.

Feb 6, 2023

By Mick Fritz, Gregory Poole

Construction blasting is always challenging when in close proximity to existing structures, but when you are next to a landmark like Sanford Stadium at the University of Georgia it can get intense. Blasting on this project was performed less than 100 feet from students studying in their dorms at Reed Hall. Some shots are only a few feet from the columns on the stadium that hold up the sky boxes where meetings were being held while blasting was being performed. If a shot goes vertical the rocks would go through the floor of the sky boxes.

Jan 1, 2011

By Jason Baird, Philip Mulligan, Caleb Baumgart

This report details the pressure variances, measured at four pressure sensors placed equidistant from the center of an airburst explosion, as the blast pressure from a single charge expands radially. Many of the empirically derived equations used for predicting the blast pressures of an explosion, assume a point source detonation and that the radial pressure expansion is equal. The authors understand that the equations used to approximate the blast pressure may not have 100 percent agreement with the observed pressure. However, during previous research at Missouri University of Science and Technology (Missouri S&T) the pressure variances had a range of 1,200 psi, between the four pressure sensors placed two feet from the center of a 1/2-pound (226.8 gram) of hand packed C4. The variances indicated that at the close distance from a suspended explosive charge the pressure does not behave as that observed from a point source.

Jan 1, 2014

By Carlos Alvarado, Hernan Narea, Jhon Silva, Bryan Townsend, Katherine Gil, Brayan Caceres, Felipe Pontanilla

With the promising development of new technologies, automation in Drill and Blasting (D&B) is on the horizon. The data generated in all D&B activities, which is currently segregated, can be linked to become information and carry a logical meaning. This information can be used to identify critical activities and make decisions regarding corrective measures to accomplish the goals of D&B. Minera Caserones, supporting Alert2Gain (A2G), and Dyno Nobel, has been working on the development of a quality assurance and quality control (QAQC), system for the mine involving all D&B activities. The main variables in the model for D&B include data from the geology of the deposit, drilling, explosive products, and material loading, among others. To create the model, the mine is divided into blasting polygons. Those polygons are part of a block model. The block model is assembled following different rules, such as: • Block sizes of 4m x 4m x 15m, • Classification of the blocks to a particular blasting polygon using a geospatial intersection algorithm, • Algorithms connect all the pieces of data automatically with the minimum of human intervention and populate the block model, Because measuring data for each block is impossible, another set of rules and algorithms completes the model. Dyno Nobel generates an essential set of data for the QAQC system. Explosive truck loading rates and explosive products, among other data, are also included in the system. The system autogenerates reports every hour, and a summary of the results of each mining day (a mining shift of 12 hours) is distributed by email to all responsible persons to identify the critical tasks and then to make the proper adjustments to accomplish the goals of D&B. The information is updated every hour and available through a dashboard for easy and straightforward interpretation. This paper explains the conceptual details of the QAQC system implemented in Minera Caserones, how the data is aggregated automatically from the different sources, shows examples of the type of information in the dashboard, and presents a successful case where a deviation was detected, and the corrective measures that were implemented to keep the performance of the D&B activity. The paper finally discusses the next steps toward an autonomous D&B system based on new AI technologies, with minimum human intervention.

Jan 21, 2025

By Lon Santis, Michael Swisdak, John Tatom

The Institute of Makers of Explosives (IME) and A-P-T Research, Inc. (APT) have developed a quantitative risk assessment tool called IMESAFR (IME Safety Analysis for Risk) for managing risk from various activities undertaken in the commercial explosives industry. The first version was completed in 2006 and Version 2.0 of the software was completed in 2012, incorporating several major new features. The platform is now based on a Geographic Information System (GIS), providing a bird’s-eye-view to help visualize facility layouts and risk. Spatial data on potential explosion sites and exposed sites can now be automatically transferred from the images to ease users’ data input. Use of GIS data provides the ability to check facility compliance with quantity-distance (QD) standards such as the American Table of Distances (used by the Bureau of Alcohol, Tobacco, Firearms and Explosives, ATF), the NATO standard (used by Natural Resources Canada and other nations), or a user-defined table. Research conducted and knowledge gained over the last 10 years enabled changes in the algorithms and models that provide greater fidelity and reduce conservatism. Expert users can change global settings to more accurately match actual site conditions and the program runs using either Imperial (English) or SI (metric) units of measure. These changes and other new features are discussed and demonstrated.

Jan 1, 2013

By Robert Hopler

209. Nitro-glycerine is produced by the action of nitric and sulphuric acids on glycerine, and is a heavy liquid of oily appearance, of specific gravity about 1•6, varying from colourless when quite pure to a yellow or brownish yellow. It is of a very sweet taste, and without odour, and is an active poison. Mere handling of it will in most persons induce sickness and headache. It explodes when heated to about 360° F. or from shock, but in small quantities it ignites and burns with some difficulty by the mere contact of flame.

Jan 1, 2011

By R. Alford

In the modern world of demolition safety is paramount and unnecessary or unquantifiable risks are not accepted (FasterCapital, 2024) and all risks must be kept As Low As Reasonably Practicable (ALARP) (BSI, 2017). This principle has led to a huge reduction in deaths in the last 50 years and the statistics continue to improve although this is starting to plateau (Beal, 2007). Under normal circumstances, this is now simply part of the normal way work is done and systems are in place to ensure both safety and economic profits are assured. What happens when the environment is less controlled and risks are unknown, such as after a natural disaster, war, an accident or a stand-up from a failed demolition attempt? A dangerous structure cannot responsibly be left alone with a fence around it so some action must be taken, but how can this be done safely and responsibly? An incident in Didcot, England in which half of a power station’s boiler house being prepared for an explosive demolition collapsed suddenly, killing four men in 2016 provides a useful case study of how technology, creativity and planning can be used to conduct complex demolition fully remotely to avoid any further risk to life.

Jan 21, 2025

By Calvin Konya, Steven S. Spagna, Ed Smith

During Summer 2001, the U.S Army Corps of Engineers awarded a contract to the construction firm of Bush and Burchett of Allen, Kentucky, for the purpose of developing a 13 acre redevelopment site by removing approximately 2.5 million cubic yards of rock (fig. 1). The Redevelopment Site will be the future home for a large portion of the City of Grundy, Virginia. Additional work items include the construction and relocation of 3,000 feet of the Norfolk Southern railroad bed, the placement of 95,000 cubic yards of fill and the placement of 16,000 cubic yards of stone slope protection along the Levisa Fork River. Bush and Burchett received a notice to proceed with construction in July 2001. Currently, the contract is near completion. Current activities include: hauling of material from the Redevelopment Site to the disposal area; placing fill material on the Redevelopment Site, and placing Stone Slope Protection (SSP) along the Levisa Fork river. Approximately one year into the construction highly weathered rock, degraded to near soil- like condition, was encountered in the upstream portion of the excavation. Over one-third of the original cut slope was adjusted and the blasting specifications had to be amended to accommodate for the material that was encountered in this area.

Jan 1, 2005

By Cary Moffat, John Kita, Rick Walker

The Lac des Iles Mine, in an isolated area of NorthwesternOntario is a relatively new open pit platinum and palladium mine. They were encountering problems with the equipment and production scheduling when ramping down to begin production on the subsequent benches. A co-operative effort between Lac des Iles Mine operation people, ICI Explosives, and the mines drilling and blasting contractor - Consbec Inc., resulted in a decision being made to use full depth sinking cuts to provide access to the next bench.

Jan 1, 1996

By Mark S. Stagg, Rolfe E. Otterness, Farrokh Djahanguiri

The U.S. Bureau of Mines (USBM) evaluated empirical equations that predict fragmentation from underground stope rounds. Controlled blasting is necessary for creating leaching stopes that maximize the recovery and minimize backbreak of the perimeter wall. This paper presents the fragmentation results from one of the three drop-raise blasts used to develop a reduced-scale cylindrical stope, 1.8 m in diameter and 6 m in height. The stope is located in the Colorado School of Mines Experimental Mine (Edgar Mine) in Idaho Springs, Colorado. This stope is part of a USBM research effort to determine the feasibility of incorporating in situ leaching of rubblized stopes into active underground metal and nonmetal mines.

Jan 1, 1994

By Juan Pablo Guevara, Victor Munoz, Rob Bush, Gonzalo Marias

Cerro Negro Mine, property of Goldcorp Inc., is in the process of developing four separate underground access ramps for the exploitation of high grade, narrow vein gold deposits with vertical to sub-vertical dips. The Mariana Central, Mariana Norte, and San Marcos accesses are primarily in the development stages, while the Eureka access began production stope blasting in April of 2013. Mariana Central will also begin production in May or June of 2014.

Jan 1, 2015

By Francisco Sena Leite, Raquel Sobral, Vinicius Gouveia de Miranda, Céu Jesus

"The urgent need for improvements in the control and mitigation of environmental and social conditions associated with the extraction and processing of raw materials is increasingly a demand imposed by legal entities and institutions. Therefore, this present article proposes an improvement of the estimation in the magnitude of the vibrations resulting from rock blasting methodologies in the surrounding areas,incorporating the heterogeneity caused by uncontrollable parameters, such as geological andgeotechnical characteristics. This methodology combines the use of empirical vibration attenuation lawscommonly known and with terrain discretization techniques using Voronoi’s decomposition. For thevalidation assessment of this methodology, the data set collected and compiled is composed by 87 vibration measures collected in 16 sample points in one area of study of which 2/3 of the samples were used to create the model and 1/3 for the validation. Using normality tests for statistical residue analysis,it is possible to infer that this present model has null residual mean, as well as a smaller sum of residualerrors. Comparing the methodology present in this paper with the procedures executed nowadays, areduction of the errors associated with the estimation is obvious, highlighting a better characterization of the behavior of the vibrations associated with rock blasting."

Jan 1, 2017