Search Documents

By l. Bokányi, T. Varga

"The recycling of waste car tyres is a very important environmental task. The waste tyres usually are re-used or recycled by thermal processes like pyrolysis, gasification or incineration. The main problem associated with these processes is the sulphur content of waste tyres originated from the vulcanisation process, which pollutes the environment and the valuable products (i.e. pyrolysis oil) as well. In our research the desulphurisation of waste, mechanically prepared tyre sample was systematically investigated by the biosolubilisation with Acidithiobacillus thiooxidans, strain Karitas. Parallel, the experiments with sterile 9K nutrient medium were also carried out. It was found that the vulcanisation sulphur can be solubilised due to both the bio- and the chemical leaching, although the bioleaching is more effective. The solubilised vulcanisation sulphur then forms precipitates. The precipitates are forming in the bulk solution, as well as on the surface of rubber particles. The origin of the precipitates was investigated using XRD and scanning microscopy with micro probe. The origin of the precipitates is different: while in the process of the vulcanisation sulphur solubilisation with 9K medium the jarosite (KFe3+3(SO4)2(OH)6) forms, the course of the biosolubilisation with Acidithiobacillus ferrooxidans Karitas is accompanied by the formation of the jarosite and the halotrichite (FeAl2(SO4)4 · 22H2O) as well. The formation of the latter is the biomineralisation. The mechanisms of the bio- and chemical solubilisations are rather different as it was found and experimentally proved by several tests, and depends on the retention time of the solubilisation. Special efforts were done to elaborate the proper separation of the precipitates from rubber particles. Combination of intense dynamic stirring and recycling flotation process to remove the precipitates was applied for this purpose. The surface properties of synthetic jarosite were revealed using zeta-potential measurements at different pH and in presence of collectors. The parameters of the flotation were chosen based on the revealed surface properties of the precipitates. Finally, the sulphur recovery of the recycled rubber was achieved as low as <0.5%, sulphur content of it 0.17%, 12-times lower than that of the waste tyre sample after mechanical preparation."

Jan 1, 2018

By P. C. Beuria

Iron ore concentrate contains different mineral phases viz. hematite, magnetite, goethite, kaolinite, and gibbsite. Presence of some of these phases like goethite, kaolinite, and gibbsite contribute to the loss on ignition (LOI) content of the sample. Iron ore fines (pellet feed) are pelletized for utilization in DRI & BF processes. In the present pelletization technology i.e., straight grate and grate kiln processes, the LOI in the ore should be within the range of 2.0-2.5%. LOI content in the iron ore concentrate is found to be more than 4% after beneficiation of low-grade iron ore. It is therefore difficult to produce good quality pellet because of high LOI content. The LOI content of the sample is a detrimental factor in the pellet making. For effective pelletization, the LOI content in iron ore fines needs to be reduced before pelletization. It can be reduced by fluidized bed roasting. The objective of present work is to understand the kinetics of removal of LOI from iron ore fines. The effects of bed depth, temperature, and residence time on reduction of LOI content in iron ore fines were studied using muffle furnace. The process of roasting was carried out at four different temperatures varying from 400 to 950 °C with a variable residence time of 30, 45, 60 & 75 minutes and at bed depths of 16, 32, 48 & 64 mm. In all instance of experiments carried out, one of the parameters was kept constant. It was observed that at 850 °C and 30 minutes of residence time, there was sufficient removal of LOI in static bed condition even at a high bed depth of 64 mm. Keywords: LOI, pellet feed, fluidized bed roasting, goethite

Sep 1, 2012

By Felipe Sepulveda, Edelmira Gálvez, Luis Cisternas

"In mineral processing, the recovery and/or concentration of the value components cannot occur in one operational stage, therefore requiring the use of separation circuits based on several flotation stages. The components to be separated are typically distributed at different concentrations and different particle sizes, resulting in different levels of recovery. Typically, more than one value component must be selectively removed by exploiting the differences in the components’ floatability at different pH values, pulp potential and particle size. Several methods for the design of these circuits are available in the literature, but comparatively few studies present circuit analysis tools or address the design of a multiple-product flotation circuit. In this study, global sensitivity analysis was used to analyze a flotation circuit with several products, such as copper, lead and zinc. This analysis was based on the Eureka mine concentrator plant. The analysis was performed for each of the sections of the circuit as an overall evaluation of the circuit. The Sobol’ method and the correlation method were used to evaluate the Eureka mine concentrator plant using the SimLab 2.2 software."

Jan 1, 2014

By C. A. Perez

Estimation of rock composition in mineral plants is important to determine rock size and grindability which in turn may improve control of the grinding process. Variations in ore grindability and size distribution directly affects mills power consumption and throughput. Therefore, it is desirable to develop new tools to estimate rock lithological composition. In this paper, a new method for lithological classification based on machine vision is proposed. The method is based on a single video camera and employs information about texture using several different spatial scales. Texture information is extracted from rock images using Gabor filters that can be adjusted at different spatial scales and orientations. After feature extraction, rock images are classified using support-vector machine (SVM). The method was tested on a database containing sub-images of 64x43 pixels of five ore types as follows: massive sulphide (MS), disseminated sulphide (DS), net textured (NT), gabbro (G), and peridotite (P). These ore types were assigned to three grindability classes: soft (MS), medium (DS and NT) and hard (G and P). The database was divided in 2 subsets for training, cross validation, and for test. Classification accuracy is compared with previously published results on a dataset with three different classes of rocks according to their hardness. Results show that our proposed method reached significant improvements (between 13%-20%) in classification accuracy relative to previously published results. Keywords: rock classification, lithological classification, grindability estimation, Gabor feature extraction, texture features

Sep 1, 2012

By A. V. Bogdanovich, S. A. Urnysheva

"Gravity and X-ray luminescent separation methods are generally used in processing of diamond ores. X-ray luminescent separators are applied for separation of diamonds from feed ore size fractions from 100 to 10-15 mm size and for final treatment of gravity concentrates over 1 mm size. Gravity separation machines used for diamond ores separation are heavy medium cyclones and pneumatic jigs. One of the most important parameters, to a large extent affecting diamonds recovery from ore, as well as processing costs and specific energy costs, is size of dumped final tailings. That was exactly the purpose of the studies, the results of which are described in this paper. The studies performed on different ores showed that in order to achieve high recovery results, it is necessary to dump heavy medium separation tailings below 3 mm size. Separation of final tailings of -6+1 mm size by jigging is also possible. However, with a view to exclude extra diamond losses, it is necessary to maintain jigging concentrate yield approximately at 25% from starting feed, with its subsequent cleaning in heavy medium cyclones. In addition to that, it is necessary to separate 20-25% of middling with diamonds content at feed ore level and subject it to grinding. This will complicate flow sheet, but reduce load on heavy medium cyclones. In order to develop optimal flow sheet for gravity concentration of a specific diamond ore, large-scale investigations are required, including technical-and-economic assessment of separation alternatives. INTRODUCTION In processing of diamond ores, gravity and X-ray luminescent separation methods are generally used. It is common practice to apply X-ray luminescent separators for separation of diamonds from feed ore size fractions from 50 (100) to 20 (10) mm size and for final treatment of gravity concentrates over 1 mm size. With that, X-ray luminescent separation tailings larger than 3-6 mm size are reground and delivered to gravity concentration processing stage. Middling products circulation volumes are large, not infrequently necessitating decrease in concentrating plants capacity, especially with mining in deep workings of deposits, where ore strength is higher (Goryachev, 2010; Vaginov, 2000; William, 1988). Diamond ores preparation before processing is accomplished by means of roll-screw crushers and autogenous grinding mills, minimizing probability of free diamonds damage in liberation from barren rock. In re-crushing of size fractions that are “difficult” in autogenous grinding, high pressure grinding rollers are applied (Burchardt, 2014; Fedotov, 2011a, 2006b)."

Jan 1, 2018

By R. V. Kononko, A. Yu. Chikin, R. N. Rakhmeev, Yu. O. Fedorov

"The focus of the study is finding a solution that can help to improve diamond recovery in diamond-bearing gravity concentrates upgrading flowsheets. The purpose of the study was to develop and prove scientifically a separation method of diamonds recovery from gravity concentrates regardless of their fluorescence ability induced by X-ray radiation. Two promising recovery methods applicable to diamonds of this type are proposed, i.e. an X-ray radiometric method based on an instantaneous analysis of a secondary X-ray spectrum of separated particles, and a triboelectric method that relies on noncontact measurements of particle charges obtained during its motion in a vibratory tray. As a part of the laboratory study, X-ray fluorescence spectra of the collection of diamond crystals and main associated minerals and rocks at a particle size of -6+3 mm were produced. The analysis of the produced secondary X-ray spectra showed a significant difference between crystals, minerals and rocks within the analytical area of Ca, Fe and Zr due to the absence of calcium, iron and zircon elements in diamonds. Additionally, the scattered X-radiation level of diamonds substantially increased under the influence of X-ray radiation. Such a difference is a physical base of a new method of diamonds recovery from mineral mixtures. The laboratory study on triboelectric characteristics showed that a significant portion of diamonds gained an electric charge of a magnitude that was much higher, compared to associated minerals and rocks. The laboratory and industrial tests and the separation indicators demonstrated a high efficiency. A proposed X-ray radiometric method provides recovery of all types of diamonds regardless of X-ray fluorescence levels, with high selectivity and recovery rate of at least 98%. This proposed separation method is protected by a patent of Russian Federation (No. 2551486, “A method of X-ray radiometric separation of diamond-bearing materials”). Triboelectric separation organized in two stages (main and control) ensures recovery of up to 98-100% of diamonds at a particle size -5+2 and -2+1 mm,. More than 10 triboelectric separators successfully operate in active diamond processing plants in the Russian Federation."

Jan 1, 2018

By G. I. Voiloshnikov, V. E. Dementyev

"One of the most important advances in the world gold metallurgy is the introduction of adsorption technologies for processing of ores and concentrates. «Adsorbent-In-Pulp» process allows to eliminate pulp filtration that is especially important during processing of clay and slime bearing ores. “Adsorbent-In-Leach” process is one of the ways for processing of preg-robbing (carbonaceous) products. High efficiency, increased metals recovery, decrease in capital and operational costs, possibility of easy control and adjustment are the advantages of adsorption processes. Anion-exchange resins and activated carbons are used as adsorbents. This paper presents Irgiredmet experience on gold adsorption technology using both adsorbents (RIP, RIL, CIP, CIL processes). It includes results of long-term studies of different theoretical and practical issues of adsorption processes. Irgiredmet started development of ion exchange technology (RIP, RIL) in 1964. Laboratory and pilot plant tests were conducted to develop process design criteria for 15 RIP plants of the former USSR. During this test work a great number of newly synthesized resins including strong- and medium-base resins was studied, different types of adsorption feed (ores and concentrates) were tested; some theoretical regularities of adsorption process were investigated; the technology of two stage adsorption for silver gold ore, improved flowsheet for gold elution and resin regeneration, designs of technological equipment for adsorption, elution, electrowinning processes including pulsation columns, electrowinning cells etc. were developed. Irgiredmet took part in commissioning of practically all RIP plants in the former USSR. Due to its efforts RIP process became to be the standard technology. Last Irgiredmet RIP projects include the development of adsorption technology using medium-base resin for the three mines owned by GC Petropavlovsk (Amur region, Russia). The complex of the testworks on activated carbon gold adsorption technology including the search of prospective activated carbons; study on gold adsorption mechanism; development, testing and introduction of process flowsheets and the equipment for their realization was conducted. The original gold elution process was developed. The developed CIP technology was firstly introduced at Lebedinsky gold plant (Yakutia). Now carbon adsorption technology is widely used at Russian gold mines as CIP, CIL, CIC processes. The most relevant example of CIP introduction is Svetlinsky gold plant (Ural, Russia) with capacity 8 Mt of ore/ year."

Jan 1, 2018

By Partha Patra

Numerous proteins of varying properties are available in extracellular bacterial proteins (EBP) isolated from Paenibacillus polymyxa. EBP was fractionated through ammonium sulfate precipitation in a controlled fashion and characterized through SDS-PAGE technique. Different groups of proteins, (Group A~D) exhibited varying degrees of surface affinity to minerals such as quartz, pyrite, chalcopyrite, galena and sphalerite. Interaction with mineral specific bioproteins rendered pyrite and chalcopyrite hydrophilic while surface of quartz, galena and sphalerite turned more hydro-phobic. Specific groups of proteins could thus be used for selective separation of galena, sphalerite and quartz from pyrite and chalcopyrite (as a mixed sulfide) through microbially-induced flotation or selective flocculation.

Jan 1, 2014

"Wet low intensity magnetic separation has been used for the recovery of magnetite for decades. As high-grade reserves continue to decline, low grade magnetite ores are being targeted for iron production. Low grade magnetite mineralisation is typically fine grained and requires fine to ultrafine grinding (P80 40 - 30 µm) to liberate it from, predominantly, silica/silicate gangue matrices. Grinding to such particle sizes requires high power consumption and produces excessive fines which impact negatively on wet magnetic separation and tailings dewatering. In addition, the dearth of fresh water for mineral processing in arid areas impacts negatively on the economic viability of low grade magnetite projects. These challenges have motivated innovation in dry magnetic separation technologies for the beneficiation of magnetite that can be economically applied on a large-scale. Such technology has been developed in the Cyclomag Planar magnetic separator (PMS) invented by South Australia-based Christopher Kelsey of IMPTEC P/L. The significant gangue mineralisation associated with magnetite ores in South Australia is quartz. In this study, the performance of the Cyclomag PMS on the recovery of magnetite mineral from magnetite-quartz blends was investigated. Magnetite-quartz blend were subjected to the PMS at varying control parameters - magnet discs rotation speed, inlet airflow and feeder speed. The study showed a successful dry separation of magnetic mineral from non-magnetics using the Cyclomag PMS. The PMS has potential to effectively recover magnetite mineral."

Jan 1, 2018

By Harri J. Lehto, Marja I. Oja

Empirical models used for predicting the performance of screens on the basis of capacity, cut size, water split and grade efficiency curves were evaluated. This paper reports experimental results obtained with single-deck Derrick screens. The performance of the screen was tested with limestone in a separate screen set-up, in a pilot plant and in industrial scale test runs. The results of pilot plant experiments showed that the measured water split was higher than the measured bypass. This is an indication to that water flow does not entrain the same proportion of all fine particles present in the feed which is advantageous for screening. The experimental design for the industrial test runs was made on the basis of the pilot plant tests. Suitability of the existing models has been checked and accuracy compared. The tests showed that best grade efficiency model was the Rosin-Rammler model. An empirical model for the evaluation of the model parameters as a function of pulp density of the feed and the load of the screen is suggested.

Jan 1, 2003

By S. Q. Zhu

Coal Water Mixtures (CWMs) are densed suspensions of coal particles in water. Viscosity is one of the most important rheological properties of CWMs and it is desired to be as low as possible. The slurry viscosity was influenced significantly by additive formation, the particle size distribution and the ash content of the coal. However, the influence of dispersants is most obvious. At present, there are several kinds of dispersants such as polymeric styrene sulfuric sodium, lignin sulfonate, humate, polycarboxy salt, ethylene epoxide surfactant. In this paper, a newly synthesized CWM dispersant has been reported, which is an efficient anionic surfactants of polycarboxylic acid type. The synthesis process includes three steps. At the beginning, the polyglycol acetate ester has been performed by acetic acid and polyethylene glycol (PEO) on the condition of acetic-acid/PEO ratio 1:1.1, at 368~373K for 30 minutes. Then the macro-monomer is prepared through the esterification of 85.71% acrylic and 14.29% polyglycol acetate ester, at 368~373K for 10 minutes. After that, the polycarboxylic acid CWM dispersant is polymerized using proper proportion macro-monomer, acrylic (AA) and sulfonic styrol sodium, at 368~373K for 1 hour. This new dispersants are used in the coal water mixtures formulation. Four kinds of coal used in the experiment are Shuang Yashan, Tunliu, Luning, Changcun samples. ? The highest concentration for shuanyashan coal is 70% when the dosage of dispersant is 0.4%, and the content of -200 meshes particles is 75.53%. As the dosage of dispersant de-creases to 0.25%, the Shangyashan CWM concentration is 67%. ? For Tunliu coal CWM concentrations are in the range of 76% to 75% when dosage of the dispersant changes from 0.4% to 0.25% at the same particle size distribution of 83.5% minus 200 meshes. ? The highest concentration for Luning coal is 69% when dosage of the dispersant is 0.4%, and the content of -200 meshes particles is 88.86%. ? For Changcun sample, the coal concentration of CWM is 73%~75% when dosage range of the dispersant is 0.35%~0.5%. The experiments show that the synthesied dispersant is quite promising for some coals CWM preparation, but a little bit coal-dependent. The Proximate and Ultimate analysis, surface characteristic measurement have been made to investigate the interactions between coal and additives.

Jan 1, 2014

By Gustav Hawlitschek, Henrique Kahn, Carina Ulsen, Renato Contessotto

"The problems related to waste dumping increased with the growth and development of large cities. In the U.K., more than 50% of landfill waste comes from construction use and the U.S. alone produces around 200 to 300 million tons of CDW annually. The exhaustion of natural sand deposits close to large urban centres stimulates the recycling of construction and demolition waste for the production of recycled aggregates as a construction material. This paper presents a flowchart for the production of recycled sand with low porosity and regular shape by the selective removal of the cement paste attached to recycled aggregates. The products characterization was carried out by the determination of the particle size and shape distribution, chemical and mineralogical composition, heavy liquid mineral separation and quantification of all present phases using a scanning electron microscopy with automated image analysis (SEM-MLA). The comminution of CDW by vertical shaft impact crusher made possible the production of a lower porosity recycled sand. The heavy liquid mineral separation showed that the proportion of low porous phases (d>2.5 g/cm3) is very high, exceeding 70% of the weight, encouraging further mineral processing separation to obtain a fine recycled aggregate with less cement paste content. The mineralogical characterization by XRD and SEM indicates that the main phases are tectosilicates, phyllosilicates and calcite which one can be attributed to both calcareous aggregate and cement paste. The precise quantification of cement paste and calcite/dolomite alone is just possible by automated image analysis. The characterization results demonstrated that proportion of phases with no cement paste attached increases progressively in denser products. The results of heavy liquid separations and image analysis are comparable and automated image analysis can be used for the characterization of phase content and their main associations."

Jan 1, 2014

By Mingxia Liu, Qi Liu, Tao Jiang

"In addition to physical parameters such as small mass and high specific surface area of fine and ultrafine minerals, chemical parameters such as the adsorption affinity of collectors on the minerals also plays an important role in fine particle flotation. In this study, we have examined collectors with two different ionized groups, carboxylate and hydroxamate, on the flotation of fine niobium oxide (pyrochlore). To facilitate comparison, two hydrocarbon radicals were tested: octyl and oleoyl, which led to four collectors that were studied: octyl hydroxamic acid (OHA), sodium octanoate (C8OONa), oleoyl hydroxamic acid (C18HA), and sodium oleate (NaOl). Small-scale flotation and isothermal microcalorimetric titration measurements were performed to determine the flotation recoveries of different sized pyrochlore and the enthalpic behavior after adsorption of the collectors on pyrochlore. It was found that the flotation performance of the carboxylate-based collectors was generally inferior to hydroxamate-based collectors. Sodium octanoate could not float pyrochlore irrespective of the particle size of the pyrochlore tested. With a longer hydrocarbon chain, sodium oleate was effective to float the relatively coarse pyrochlore (>20 µm) but its collection efficiency dropped sharply for particles smaller than 20 µm. On the other hand, the two hydroxamate-based collectors, octyl hydroxamic acid and oleoyl hydroxamic acid, showed good collecting ability to both the coarse and fine pyrochlore. The isothermal microcalorimetric titration studies indicated a consistent correlation of chain length with floatability of collectors for relatively coarse pyrochlore, as well as a positive relationship between the adsorption affinity and fine pyrochlore flotation recoveries. The key finding of this study was that efficient fine particle flotation could be achieved when strongly chemisorbing collectors were used.INTRODUCTION The first detailed study of the effect of particle size on flotation was made by Gaudin (1931) with sulphide ores. In 1942, Gaudin again demonstrated that (Gaudin et al., 1942) fine particles possess different flotation properties from larger particles. Since then the effect of particle size on froth flotation has been an important research topic by many researchers, e.g., Gaudin (1957), Miettinen et al. (2010), Warren (1976) Jameson (2010), summarizing the behavior of fine particles in terms of their low particle momentum, leading to low rate of collision with bubbles which reduces the chance of adhesion. The suggested remediation methods are mainly based on two approaches: increasing particle size or decreasing bubble size (Warren, 1976). Sand-fine splitting followed by separate flotation treatment of the sand and fines, using deep flotation cells, using starvation quantities of collectors, and using long flotation times, are also strategies to address the problems of fine particle flotation."

Jan 1, 2018

By F. Karakas

Water based paint formulations consist of some industrial minerals with quantities varying from 20 to 50 %. Quality of paint is directly related to these minerals used as pigment or filler in the production. Titanium dioxide is the most important and expensive pigment in paint formulations. Other minerals such as calcite and calcined kaolin are used as filler and mainly as a substitute for TiO2. Consequently, particle-particle interactions including adsorption, coating and size distribution of pigment mixture directly affects the paint quality. In the present paper, a new type of pigment mixture for possible use in architectural water based paints was developed through grinding. The effect of different types of grinding methods on physical properties of TiO2 and calcite mixture and the quality of paint produced by these mixtures have been revealed. Three different types of mills; conventional ball mill, vibratory ball mill and high-speed attritor were used for grinding of TiO2 and calcite. Viscosity, zeta potential and particle size distributions were used to characterize the pigment mixtures obtained upon grinding. The quality of paint was evaluated by standards based on both wet and dry paints such as viscosity, density, opacity and gloss. The paint produced with the pigment mixtures prepared in vibratory ball mill and high speed attritor showed improvement in physical properties particularly in the distribution and dispersion of mineral particles. Keywords: grinding, pigment, paint, TiO2, calcite

Sep 1, 2012

By John A. Herbst

Professor A.M. Gaudin and his students at MIT were dedicated to understanding the fundamentals of mineral processing and as a consequence were constantly searching for better quantatative descriptions of size reduction, liberation and mineral separations. I have had the good fortune of meeting Professor Gaudin and working with many the modeling pioneers who followed him. I have observed first hand the refinement of mineral processing models as they increased in realisticness moving up the steps of the pyramid (see figure below) from pure empiricism to the current pinacle of physics based models. During this journey our industry benefited significanbtly as model prediction errors were reduced from ± 20% to ± 1%. Unit operation and plant simulations improved in accuracy and speed of calculations.

Sep 1, 2012

By S. Vimalnath

The bioremediation capability of Pseudomonas aeruginosa cells was investigated for the biosorption of lead ions from aqueous solution. The various parameters such as pH, kinetics, biomass loading and concentration of lead affecting the biosorption process were studied. Complete bio removal of lead could be achieved for an initial concentration of 12.4 mg/L at pH 6.2, corresponding to typical industrial effluents. The biosorption isotherm followed Langmuirian behavior and the Gibbs free energy (?G) was determined to be-30.8 kJ/mole, indicative of chemisorption between the functional groups of the bacterial surface and lead. The biosorption kinetics adhered to a pseudo-second order model. The possible mechanisms of interaction of lead with the bacterial cells are discussed. A carbon paste electrode with a coating of biomass was developed for lead ion detection in aqueous solution using cyclic voltammetric technique. Concentrations of lead up to 5x10-5 M could be successfully detected using cyclic voltammetry, which could be improved to a detection limit of 1x10-8 M adopting differential pulse anodic stripping voltammetry (DPASV). Keywords: Pseudomonas aeruginosa, bioremediation, lead, voltammetry

Sep 1, 2012

By Richard A. Williams

The mineral processing community have been amongst the pioneer developers and early adopters of key platform technologies in analytical methods, chemistry, physical separation and advanced modelling. Fundamental research will continue to have a significant impact driven by the continued development of sustainable practices. Major drivers and challenges for change in our industry in the next two decades include: reduction in energy uses in processing; discovery of new energy materials; adoption of green chemistry routes; safeguarding of water resources; and demonstration of adherence to best practice at all times. With increasingly global mining enterprises, the provision of internationally accepted benchmarks for performance will continue to drive the creative process. This lecture highlights major opportunities around a new paradigm of Multi-scale Measurement coupled with Multi-scale Modelling, based on advanced sensors, communications and computing. Connecting real-time measurement sensors with dynamic simulation models opens up new horizons for visualising the process behaviour from an experimental and theoretical basis. Examples are given of the potential of this methodology and its implications for better design.

Jan 1, 2003

By A. V. Rasskazova

"The oxidized and mixed ores are processed by heap leaching. Primary ores with high gold content are floated. In recent years mining of primary ores with the low gold content (up to 4 ppm) has increased. Extraction of gold from these ores by floatation is technologically ineffective. Gravity concentration is ineffective for fine gold particles because of their floatability. The research objective was assessment of the viability of processing gold-bearing ore with combined gravitational and hydrometallurgical methods and testing of recovery of metals from a gold-copper oxidized ore chloride-hypochlorite leaching solution. The advantage of chloride-hypochlorite lixiviant is the low cost of reagents which is produced by the electrochemical synthesis of NaCl solution with the addition of HCl. The adsorption of chlorine compounds by a mineral matrix and its ability to oxidize the refractory ore components and allows for the application of chloride-hypochlorite systems for gold recovery for both oxidized and primary ores. The complexity and problem in using a gold–chloride system is the strong adsorption of gold–chloride complexes onto mineral surfaces, such as goethite, quartz, and alumina. In preliminary testing, gold recovery from gravity circuit gold bearing concentrates processed by agitation leaching in chloride-hypochlorite solution, gold recovery has reached up 82% after 4 hours of leaching. Chloride-hypochlorite leaching of copper-gold oxidized ore with preliminary processing by sulfuric acid provided for 94 % gold recovery to solution. Understanding of ecological hazard of cyanides is the motive power of researches in the field of search non-cyanic chemistries to provide for technologically and economically effective solvents of gold. Soluble compounds of chlorine with a suitable oxidizer are one of the alternatives to cyanides. Basic researches of gold extraction by chloride-hypochlorite solution have shown high rates of gold recovery.INTRODUCTION Because of the continued and growing environmental concern for the use of cyanide for gold processing, interest for the use of non-cyanide lixiviants, especially with halides has renewed recently (Tran et al., 2001; Ferron et al., 2003; Bhaghalha, 2007). Leaching solutions based on halides (chloride, bromide and iodide) are viable alternative to cyanide (Kwang et al., 2008). The major disadvantage of the chlorine–chloride system is the high reactivity of chlorine in reaction with sulfide and gangue carbonate minerals. It is believed that only high grade materials may be treated by chlorine–chloride systems economically (Baghalha, 2007). Another important problem of the application of gold–chloride complex is that it tends to be rather unstable and may re-precipitate upon contact with a reductant, such as sulfidic minerals of ore. It is well known that Au(III)–chloride hydrolysis species are strongly adsorbed by goethite, quartz, and alumina (Machfsky et al., 1991). To minimize adsorption of gold–chloro complexes, it works best to minimize the adsorption time."

Jan 1, 2018

By G. Venkateswara Rao

The jigging of ferrous ore to produce higher-grade products has been practiced for many decades. This is due to easy separation, a beneficial trade- off between operating cost and reduced yield relative to Dense Media Separation (DMS). Jigging becomes prominent for beneficiation of iron ores in the coarser size range. At present drive is towards the use of under bed air pulsed jigs for the beneficiation of ferrous ores. The main advantage is that the under bed air pulsed jigs are capable of generating the large pulse of amplitudes required to fluidize a deep bed of heavy ores particularly lump iron ore up to 40mm size. The major jig parameters effecting the jigging operation are bed height, shape of the pulse, residence time, operating pressure, valve cycle time and water flow rate. With the pulse shape set correctly for optimum stratification rate, even it is still necessary to provide enough residence time, to ensure the difficult material will take time to migrate to the expected layer in the bed. In order to find the Jig Stratification Index (JIS) parameters like bed height, operating pressure, water flow rate, cycle valve time and shape of the pulse were optimized first by conducting various tests. Typical Iron ore samples from Odisha (both lump and fines) were subjected to stratification studies at residence time of 1, 5 and 15 minutes. Jig Stratification Index (JSI) for both lump (0.30) and fines (0.20) were determined by using APIC Jig. The maximum possible JSI was calculated by using heavy liquid separation test (0.42 for lump and 0.24 for fines). It is found that the jig bed JSI is less than the Heavy liquid JSI for both lump and fines. The ratio of Jig bed JSI to the heavy liquid JSI is 0.83 for lump and 0.71 for fines. The JSI and ratio of Jig bed JSI to Heavy liquid JSI are low for fines due to fluid turbulences causing some degree of remixing in the jig bed. The fluid turbulences are more for fines than lump, hence jigging of fines is difficult and challenging. Keywords: sub grade iron ore, gravity separation, jigging, apic jig, stratification, residence time, jig stratification index

Sep 1, 2012

By R. K. Dwari

The electrostatic beneficiation of coal is based on tribocharging characteristics of ash forming minerals and coal particles. The tribocharging of quartz, pyrite and coal particles contacted with various metals and polymeric materials have been measured and the charge acquisition is assessed through surface energy calculations from liquid contact angle data. The contact angles, before and after tribocharging of solids, are measured using Krüss tensiometer and Washburn?s method where the sample holders in tensiometer are specially constructed with tribocharger materials. The charge polarity and amount of charge acquired by quartz, pyrite and carbon with metal tribochargers were found in good agreement with the reported work functions of the contacting surfaces. The charge results with polymer materials differed from the work function values, presumably caused by surface contamination. The surface energy of quartz calculated by all the theoretical approaches in the literature showed that the tribocharging increases the surface energy. Both polar and non-polar components computed from Fowkes and Owens-Wendt-Rabel-Kaelble approaches dis-play that both these components increased after triboelectrification. However, the polar component divided into acid and base components, as in van Oss approach, manifest decreasing acid part and increasing base part. Since quartz charged negatively during tribocharging with metal surfaces and therefore accepted electrons, the determined acid and base surface energy components are consistent with charge transfer process. The results also elucidate an explicit correlation between the charges generated by powders and the surface acceptor (acid) and donor (base) electronic states and thereby the work functions. A novel fluidized bed tribocharger was designed and developed with internal baffle system for efficient contact electrification of mineral and maceral to produce high differential charging for efficient separation. The results achieved on coal with 45% ash content are presented and discussed.

Jan 1, 2014