Search Documents

By Y. L. Tian

Low-grade bauxite with A/S of 4.4 from Henan province was used as raw material and the selec-tive grinding of bauxite, grinding efficiency, particle size and Al2O3 and SiO2distributions of ground products were investigated using ball and vibration mills. The results show that the selective grinding can be used to realize the separation of aluminum from silicon within a certain particle size. The optimal grinding conditions of the ball mill with bauxite are as follows: grinding material to charge ratio, 1.2, charge volume ratio, 40%, pulp con-centration, 70wt%, medium size distribution, F30mm:F20mm:F15mm=20%:50%:30%. Under the conditions, the weight rate of ground product with A/S over 7.5 is 27% and the recovery of Al 2O3is 30%. The optimal grinding condition of the vibration mill with bauxite are as follows: grinding material to charge ratio, 0.9; charge volume ratio, 70%; concentration, 70%; medium size distribution, F40mm:F30mm:F20mm=20%:30%:50%. Under the conditions, the weight ratio of ground product with A/S over 7.5 is 25% and the recovery of Al 2O3is 27%. The research is significant for the rational and economical utilization of the low-grade bauxite.

Jan 1, 2014

By G. Aguilera

It is known that an addition of rigid particles into a fluid medium changes the flow field. Therefore, the rheological behavior of suspensions will be hardly Newtonian, such as their continuum phase. This phenomena was studied by Einstein in 1906 (Einstein, 1956) for the single case of spherical particles in a continuum liquid of a very dilute suspension. The final analysis applied for suspensions was derived from the evaluation of the behavior of ideal gases, finding a simple expression for the viscosity of the dispersion. All the following works about the hydrodynamics of suspensions at low and high solid contents was based in the Einstein´s model. For clay minerals suspensions where the physical and chemical properties of the particles are complex, it was found that the Einstein´s model is not a good approximation, even so for the most dilute dispersions. The present paper shows a new approximation that describes the non-Newtonian behavior of the suspensions of clays, and the attempt of understand how the different fine sizes, shapes and physico-chemical properties of clay particle surfaces give specific characteristics of plasticity, viscosity or visco elasticity to suspensions. Keywords: viscosity, clay minerals, einstein´s model, dilute suspensions

Sep 1, 2012

By S. Dwarapudi

Pelletizing of Indian chromite ores is more challenging due to their high refractory nature. High Cr/Fe ratio and high MgO content in these ores demand high firing temperatures and longer firing cycles but often result in low strength fired pellets. Aim of this study was to develop cold bonded chromite pellets for smelting in submerged arc furnace (SAF) from chromite fines using suitable binder that induce less gangue into the pellets but cures quickly. Different binders were studied through laboratory pelletizing experiments for their suitability for cold bonding the pellets. As result, a composite binder comprising organic and inorganic binding agents was found to be suitable and pellets made from the same were tested for their low and high temperature behavior. High temperature reduction studies revealed that pellets were resistant to disintegration up to 1200 °C.

Sep 1, 2012

By Kang N. Zhong, Hui H. Luo, Yi H. Wei, Yu L. Wang

"More than 85% of phosphorous reserves in China occur as middle-low grade phosphate of sedimentary origin. The main gangues are dolomite, quartz, silicates, and clays. The characteristics of minerals are finely disseminated. Flotation results have shown that the floatability of apatite of this kind of ore is much worse than that of igneous and metasedimentary origin because of its high specific surface area. Although some effective depressants, such as naphthalene sulfonate and phenanthrene sulfonate, are used to decrease the MgO content in the P2O5 concentrate, its presence is still high (about 2%) in the Chinese concentrates. Meanwhile, the wastewater may cause some environmental problems. Batch flotation results and measurements of specific surface area and CO3 2- have revealed that there is a relationship between the floatability of apatite and the surface area.A two-stage flotation flowsheet, which includes a combination of direct and reverse flotation, was developed for beneficiating sedimentary phosphate ores. The direct flotation was conducted in an alkaline medium and most of the apatite and carbonate minerals floated leaving quartz and siliceous gangue in the sink. In the reverse flotation circuit, the floated product was further beneficiated in an acidic medium to eliminate the carbonate as a float product. Apart from the high quality of concentrate, the two-stage flotation also facilitated the treatment and the recycling of wastewater. A wastewater recycling procedure was developed and tested in a continuous flotation process. The key factor was the careful selection of effective and non-toxic reagents."

Jan 1, 2003

By S. Castro

Molybdenite flotation is strongly depressed at pH higher than 9.5 in the flotation of Cu-Mo ores in sea water. Chemically sea water contains mainly Na+ and Cl- ions, but also some secondary ions, such as SO42-, Mg2+; Ca2+, HCO3-; etc., which are not necessarily indifferent for the flotation of molybdenite. The natural floatability of molybdenite in sea water and in NaCl solutions containing different secondary ions is investigated by micro-flotation tests. The tests indicate that the floatability of molybdenite in alkaline media in 0.6 M NaCl solutions is not affected by the presence of anions, such as, SO42- and HCO3-, at concentrations similar to those occurring in sea water. However, a strong depression of molybdenite at pH ranging from 9.5-10.0, is produced by the alkaline earth metal cations (Ca2+ and Mg2+ ions), dissolved in distilled water or in 0.6M NaCl solutions. It was found that effect of Mg2+ions is significantly stronger than Ca2+ ions. Effect of both ions is attributed to hydrolysis and adsorption of MOH+ hydroxy-complexes. This is followed by subsequent precipitation of hydrophilic colloidal hydroxides at the molybdenite/solution interface, and in bulk solution.

Sep 1, 2012

By Seher Ata

This paper is concerned with the coalescence behaviour of two bubbles in dilute solutions of cetyltrimethylammonium bromide, methyl isobutyl carbonil and triton x-100. Two bubbles were produced at the tips of adjacent capillaries and the time elapsed between the first contact of the bubbles and film rupture was determined by means of a high speed camera. It was found that the amount of surfactant required to stabilise the bubbles increased in order of CTAB>TX-100>MIBC. The probability of coalescence decreased sharply with increasing surfactant concentration in CTAB and TX-100 solutions while with MIBC each bubble pairs resulted in coalescence, giving hundred per-cent coalescence probability.

Jan 1, 2014

By J. Wiese, K. Corin, Z. Song

"Relating flotation performance to the electrochemical characteristics of a pulp is complex both in fundamental research and in practice. In the case of thiol collectors, different Eh values in the flotation system can result in the formation of the dimer or the metal thiolate which may or may not enhance the hydrophobicity of the mineral. Reducing or oxidizing conditions in a flotation system, viz. changing the Eh value, are usually manipulated to achieve an optimum flotation response by control of pH and dissolved oxygen levels in the system. A variation in pulp potential may also be achieved by the addition of potential modifiers such as sodium hydrosulphide (NaHS), sodium hypochlorite (NaClO) or hydrogen peroxide (H2O2). There exists anecdotal evidence which suggests that the addition of small amounts of H2O2 to the flotation process can improve sulphide mineral recovery. The objective of the present study was to investigate the effect of the addition of the potential modifier, H2O2, on sulphide mineral recoveries and grades in the flotation of sulphide minerals from two copper bearing ores from China and compare the results to those obtained for a PGM bearing ore South Africa. Batch flotation tests were conducted using the three different ores at the natural pH of the different systems, in the presence of a xanthate collector and the absence and presence of H2O2 as a potential modifier. The results indicate that the addition of carefully controlled low concentrations of H2O2 resulted in improvements in flotation performance. INTRODUCTIONElectrochemical potential as a control parameter in the flotation of sulphide minerals has been widely studied (Allison et al., 1972; Gardner and Woods, 1979; Ross and Van Deventer, 1985; Chander, 2003; Woods, 2003; Javadi, 2013). There is concensus that in order to be recovered during flotation, sulphide minerals require a suitable redox environment. During the flotation process thiol collectors and sulphide minerals are involved in electrochemical reactions which result in the formation of hydrophobic species at the mineral surface (Finkelstein and Goold, 1972; Rand and Woods, 1984). Sulphide minerals act as semiconductors and electrons are transferred during the interaction of the mineral with collector. The resultant potential difference and its magnitude are responsible for the transfer of electrons and the rate of the reaction (Bard and Faulkner, 2001; Fuerstenau et al., 2007). Reducing or oxidizing conditions in a flotation system, viz. changing the Eh value, may be manipulated to achieve an optimum flotation response by control of pH and dissolved oxygen levels in the system (Heyes and Trahar, 1979). The use of potential modifiers viz. reducing or oxidizing agents which include H2O2, NaClO, and NaHS, is an alternative method by which to control the potential of the pulp in a flotation system which may or may not promote the flotation of desired minerals (Rao, 2004). The oxidizing agent, H2O2, undergoes a cathodic reaction which can result in the enhanced flotation of valuable minerals. The potential of the system is increased which results in a shift in the mixed potential of a mineral. The magnitude of the over-potential influences the rate of the oxidation process and thus the flotation response of sulphide minerals (Kocabag and Guler, 2008). Equation 1 shows the proposed oxidation of xanthate by H2O2 (Lipkina and Streltysn, 1970)."

Jan 1, 2018

By Matthew Thurley

Optimisation and control of comminution, pelletization, and agglomeration processes is a complex task with large potential for gains in productivity, energy efficiency, and particle size distribution quality. One factor in realising these gains is the requirement for fully-automated online particle size distribution measurement. Moreover, online particle size distribution measurement that is based on the particles on the visible surface and can avoid or mitigate substantial errors that result from under-sizing overlapped particles and over-sizing areas of fines particles. Literature review indicates a body of substantially 2D photographic based particle size measurement systems that suffer from a large number of significant errors except in the simplest case of a monolayer of particles under good illumination with limited color variation in the material. In order to measure the visible particles on a pile there are a number of requirements including; avoiding particle delineation errors due to variation in material color and shadows, detect overlapping versus non-overlapping particles, and identify areas of fine particles as fines and not large rocks. Results are presented using a fully-automated online measurement system of crushed rock on conveyor belt using a 3D surface laser profile. The system provides continuous online measurement and results are shown on over four hours of production after the primary crusher. Size distribution results are calculated using volumetric estimation of the particles on the surface of the pile. The results show a strong capability to discriminate size variation especially in the 10% and 20% passing values. Furthermore results show that if areas of fines are misclassified as large rocks, and overlapped particles misclassified as small rocks, then a near complete loss of discrimination occurs for the P10 and P20 values which become largely constant values.

Jan 1, 2014

By W. G. Liu

Phenyl malonic acid (PMA), a new chelating collector, which contains a phenyl structure and a malonic acid chelating group, has been synthesized and its collecting capabilities to calamine, hematite, quartz and hemimorphite are also studied in laboratory. From the experimental results, it can be seen that the PMA has somewhat flotation ability to calamine, hematite and quartz, while it nearly has no collecting ability to hemimorphite. With the increase of PMA concentration, the flotation recovery of calamine increases. When the dosage of PMA was 560g/t and at pH=7~9, the flotation recovery of calamine gets its maximum of 45.94%. The test results about the influence of pH on the flotation recovery of quartz show that the flotation recovery increases with the increase of pH, and the maximal flotation recovery can be gained in alkaline media. On the other hand, PMA has stronger flotation capability to hematite than to other minerals. The flotation recovery of minerals increases with increase of PMA concentration. When the dosage of PMA is 560g/t and at pH=5~7, the flotation recovery of hematite is 82.96%. Mean-while, the influence of pH on the flotation recovery of hematite was studied and test results showed that, as pH increases, the flotation recovery sharply rises until pH=4, then the increasing rate de-creases outstandingly, at pH=6 the flotation recovery reaches its maximum of 82.96% and it de-creases speedily in alkaline media. Finally, through the measurement of infrared spectroscopy and in terms of solution chemistry of collector, the flotation mechanism has been discussed. It was concluded that the adsorption of PMA on minerals surface is chemical adsorption in nature through two oxygen atoms in the polar group of phenyl malonic acid chelating with the metal ions of minerals surface to form a hexagon-cycle chelate complex: C(=O)-O-M-O-(O=)C.

Jan 1, 2014

By A. V. Kurkov

The secondary action reagents (SAR) are organic diphilic compounds capable of altering ac-id-base and donor-acceptor properties of the main collector and consequently the energy of collector interaction with the mineral?s surface, its hardness and fixation forms ratio through associates formation via the hydrogen bonds. When the basic flotation conditions are being established, convergence of the electronic structure of the collector and the mineral being extracted due to minerals surface preconditioning with modifiers and the most efficient collector choice. At the next stage of the selective flotation condition establishment SAR is selected for a more precise adjustment of the energy of the collector fixation on the mineral. Such an approach makes it possible to solve efficiently various issues of flotation separation of non-sulfide minerals. In particular neutral organic substances containing groupings C==O, S==O, P==O (ethers of carboxylic and phosphonic acids, amides of carboxylic, phosphonic and sulfonic acids) were proposed as SAR. In order to enhance the flotation process selectivity in the conditions of water recycling including the selectivity of carboxylic collectors especially in the environment of high hardness water flotation, it was proposed to use SAR with long hydrocarbonic radical and groups with enhanced electronic density within the molecule: N-methylolamides of alkylphosphoric acids and ethers of methylphosphonic acid. Introduction of small amounts of these compounds alongside with the main fatty-acid collector enhance the performance of fatty-acid flotation of fluorite, beryl, columbite etc., lowers the collector consumption, and completely compensates the depressive effect of recycled water. Di-2-ethylhexyl ether of methylphosphonic acid?CH3P(O)(OC8H17-i)2 (hexarane) was more thoroughly researched as such an agent within fatty-acid flotation process. Following aspects of the flotation system were studied: interaction of oleic acid and sodium oleate with hexarane in the liquid phase (infrared spectroscopy); heat emission under the interaction of hexarane-oleic acid ? sodium oleate ? calcium salts (isoperiboric diathermic colorimeter); colloid-disperse state of the collector influenced by hexarane (nephelometric analysis); dynamics of the mineral surface hydration due to the agents (method of indicator negative adsorption); hexarane effect upon the interaction of fat-ty-acid collector with calcium salts (complexometric method with Trilon-B); floatability of pure minerals (quartz, microcline, beryl, columbite) in Hallimond tube; hexarane effect upon oleic acid (sodium oleate) adsorption (nephelometric method for identification of the residual content of oleic acid and its forms within the solution). Upon the research it can be definitely concluded that the adjusting effect of such compounds as hexarane within the non-sulfide minerals flotation process is mainly determined by their interaction with the main collector both within the pulp and at the mineral surface with associates formation due to the hydrogen bond. The consequence is calcium oleates destruction with the release of the most active collector under flotation in hard water environment which determines the efficiency of hexarane joint application with fatty-acid collector under recycled water supply. Therefore the introduction of the class of secondary action reagents is supported by their operation mechanisms and flotation process function and determines a new approach to the development of efficient conditions of selective flotation separation of non-sulfide minerals.

Jan 1, 2014

By A. Gülmez

The complex ore deposit containing fluorite, barite and bastnaesite minerals is located in Beylikova Region of Sivrihisar town of Eskisehir Province of Turkey. The ore contains 40.80% CaF2; 35.35% BaSO4; 2.01%Ce; 1.5% La; 0.39% Nd and 0.1% Th. Barite recovery from this ore by flotation of the HCl leached tailings is presented in this paper. Rare earths are recovered by leaching. The leached residue (tailings) containing fluorite and barite is subjected to froth flotation to recover barite. The effect of pH and collector concentration on the flotation of barite have been studied in this work.

Sep 1, 2012

By Richter, E. Charikinya

"Mineral processing unit models require information on particulate properties such as particle size, solids flowrate and mineralogical composition to model their operations. Process models that describe the separation process can be classified based on the level of information required from the ore, i.e. the feed stream to the separating unit. The most comprehensive level of mineral processing models is the particle-based modelling approach. Particle based modelling describes a modelling approach where mineral composition, mineral liberation and textural information of particles making up the process streams is used in modelling. The advantage of this approach is that all model streams carry particle level information (size, liberation, shape). This information is obtained by applying automated mineralogy techniques such as Quantitative Evaluation of Minerals by Scanning Electron Microscopy (QEMSCAN) analysis which provide accurate and detailed information on process stream particle properties. Currently the use of liberation information in modelling and simulation is rare, due to the limited number of separation models that liberation data as input. The objective of this study is to develop a particle based model for a dry magnetic separator, where mineralogical information is used directly to simulate a dry magnetic separator operation. Magnetic separation tests were carried out on high, medium and low grade magnetite ores using a laboratory magnetic separator. Streams from the separator were sampled and sized for chemical and liberation analyses. A sized mass and elemental balance around the magnetic separator was carried out. The elemental assays of each stream were converted to mineral quantities and a sized mineral balance was done. QEMSCAN measured liberation data was reconciled to the mineral balance based on mineral quantities obtained from chemical assays. This was followed by the development of a particle based model that calculates the trajectory of a single particle based on its mineral composition and textural properties. The model was tested on experimental data and was able to predict the effect of variation in process feed stream mineralogical attributes (liberation, grade, particle size) on magnetic separation performance. Results of this study highlight the benefits of the particle based modelling approach. INTRODUCTION The extraction of mineral values from ore requires liberation of the value minerals from the gangue followed by their separation. Liberation is achieved by size reduction operations (Desmond, 2008; Fuerstenau and Abouzeid, 2002). Separation of gangue material from value mineral takes place in various mineral upgrading stages such as classification, magnetic separation and flotation. In these concentration stages value minerals are separated from gangue minerals based on the physical properties of the ore particles making up the feed such as size, liberation, volume of magnetic material and density. The success of separation is related to the liberation of the feed particles, the performance of the separation technology applied, as well as the inherent characteristics of the feed material (Leißner et al., 2013)."

Jan 1, 2018

By E. R. Bobicki

"Low-grade ultramafic nickel ores, while representing a large potential nickel resource, are difficult to process due to their serpentine content. Microwave treatment is proposed as a technique to improve the beneficiation of ultramafic nickel ores by converting the constituent serpentine to olivine. The present paper reviews the microwave heating response of ultramafic nickel ores and resultant changes in mineralogy, as well as effects on grinding and slurry rheology. Beyond nickel extraction, microwave treatment improves the mineral carbon storage capacity of ultramafic ore tailings, providing a potential source of additional revenue via the sale of carbon credits. The combined positive effects, considered in the context of the whole operation, suggest an economically viable process is possible.INTRODUCTIONAs high-grade deposits become depleted, the processing of low-grade ores has become increasingly important. One such resource is low-grade ultramafic nickel ores. While representing a large source of nickel, these ores are difficult to process due to their serpentine content. Serpentine is a phyllosilicate mineral consisting of 1:1 stacked sheets of silica tetrahedra and magnesium hydroxide octahedra. There are three primary polymorphs: lizardite (platy), antigorite (corrugated) and chrysotile (coiled, fibrous). The anisotropic nature and non-spherical morphology of serpentine particles leads to complex rheology. Suspensions of serpentine minerals, especially those of chrysotile, exhibit high viscosity and yield stress, which can have a negative effect on comminution, flotation and dewatering operations. In flotation, serpentine is known to slime-coat pentlandite, a valuable nickel mineral, and form bubble-fibre aggregates that report to the froth, reducing nickel concentrate grade and recovery. Methods used to counteract the effects of serpentine in processing include desliming, the addition of chemical dispersants, salts or acid, and dilution (Bobicki et al., 2014a). Microwave pre-treatment has been proposed as an alternative way to eliminate the deleterious effects of serpentine in ultramafic nickel ore processing by converting the serpentine to olivine via dehydroxylation, which occurs at 600-700oC (Reaction 1). Olivine is isotropic, consisting of isolated silica tetrahedra linked by octahedrally coordinated magnesium ions, and has the same surface potential as pentlandite at the pH of flotation (~pH 9). Furthermore, since olivine is more reactive to CO2 than serpentine, microwave pre-treatment creates an opportunity to store more CO2 in tailings, an attractive option for mining operations looking to increase their bottom line where carbon pricing exists."

Jan 1, 2018

By E. V. Zelinskaya, A. E. Burdonov

"In the raw aluminum production processon electrolyzers with self-baking anodes, during technological operations, flow-regulated treatment and adjustment of the electrolyte chemical composition produced by diesel and floor-rail technology, alumina and fluoride salts are spilled through the ventilation grilles of the electrolysis body aeration channels, leakage in the equipment, machinery and motorized machinery construction elements. As a result of this, a part of the bus station and the level of ± 0 (the basement room with supporting curbstones and columns, on which electrolyzers are installed) are covered with technological raw material. This leads to an increase in the conductor (bus) resistance, contact connections deterioration, cell insulation failure and raw materials loss. For example, at the enterprise ""Rusal-Bratsk"", as a result of the activity, up to 420 tons per month of alumina-containing wastes that are unfit for use in the electrolysis process are formed due to the alumina substantial contamination with salts of iron and silicon, which significantly reduces the technical and economic parameters of the electrolysis process. The main scientific problem is the processing (cleaning) of alumina-containing waste having a complex mineralogical composition of the material, its contrast and structure, from oxides of iron and silicon, using ""dry"" separation methods. In the performing the work process, qualitative indicators of the influence of external factors (air humidity, precipitation, sunlight, temperature difference) on the physicochemical processes components interaction during the raw materials storage are established. On the basis of laboratory tests, it is established that alumina-containing raw materials can be separated and photometric and gravitational separation methods used. A mathematical model of the motion of particles of primary and prepared alumina-containing raw materials in a cascade-gravity classifier was developed. The criteria and factors characterizing the alumina-containing material, as well as influencing and determining the maximum material enrichment, are established."

Jan 1, 2018

By Rob Morrison, Andrew Scott

"Long before a modern mine commences operations it has already become a wealth of information. After start up, it can generate enormous quantities of data - especially with semi-automated data acquisition by instrumented mine equipment.However, much of this data is of limited use for evaluation of (potential) performance unless it links in some way to the site business model.An underlying reason for this waste of data is that the different cultures, financial, technical, community, environmental, etc, not only have many areas of interest but also have very different conceptual models by which they evaluate performance.It is too ambitious to attempt to bring all of these cultures together - in a single step.However, the success of the Mine to Mill - project has demonstrated that substantial operational value can be added by using a more integrated approach to comminution. The next logical step is to integrate measurement and then to track performance from ore body model to saleable product and waste disposal. From resource to product also represents a path from very sparse, highly variable data to much more detailed measurement and more representative sampling.However, in both cases the data collected is strongly focused on the technical requirements - not on the business model.This paper considers how to define at least some of the key decision points in terms of some case studies.Performance data from many areas might be used to derive simple models which can then be used for forecasting and optimisation of planning."

Jan 1, 2003

By D. H. Xiong

Low grade oxidized iron ores are usually not economic to utilize. However, the development of SLon magnetic separators and other new technologies make the process cost lower and lower. In this paper, several low-grade oxidized iron ore process flowsheets are introduced. The key procedure is that at the early stage, SLon magnetic separators are applied to discharge as more tails as possible with very low cost, only a small portion of rough concentrate going to the cleaning stage, showing the new technologies are profitable for such iron ores.

Jan 1, 2014

By T. X. Hu

Pyrite ore is one of the main raw materials in the production of sulfuric acid. For a long time, the raw material containing the pyrite, which is used to produce sulfuric acid, generally contains S only 32%~45%. A plenty of residue from the sulfuric acid production contains 40%~50% Fe and 1%~2% S. Some of the residue also contains Cu, Pb, Zn and other harmful elements like As, thus it pollutes environment seriously and is solid waste. The research on comprehensive utilization of the residue has been made by many scholars. Through the study, the residue can only be used to pro-duce iron concentrate and the iron oxide red pigment. But because of the complex techniques, the low recovery, the low grade of iron concentrate , high sulfur in iron concentrate, causing second waste residue and the environmental pollution, the residue is mainly used as an accessory material in the production of cement, and is of a low value. Therefore, the iron resource in pyrite has not been used efficiently until now. In the paper, the flotation condition test, the flotation open circuit test and the flotation closed circuit test to produce high-purity pyrite concentrate with the low-grade pyrite ore in oceanic ore deposit have been carried on. Flotation reagent scheme of sulfuric acid used as activator and butyl xanthate as collector is determined. After four times depth cleaning, high-purity pyrite concentrate containing 52.82% S, 44.29% Fe, and only 2.89% impurities has been obtained. The S recovery is 99.13%, and the Fe recovery is 96.00% in the high-purity pyrite concentrate. The oxidizing roasting depth desulfurization experiment of the high-purity pyrite concentrate has been conducted. The results show that the Fe grade in the residue obtained is 68.58%, the content of S is 0.25%, the content of P is 0.0084%, the content of As is 0.0065%. The residue is a kind of high-quality iron-smelting raw material. Based on the above experiments, the industrial experiments on producing high-purity pyrite concentrate with the low-grade pyrite ore, and producing sulfuric acid and iron concentrate with high-purity pyrite concentrate have been done. The results indicate that the high-purity pyrite concentrate with the S grade of 51.24%, the Fe grade of 44.15% has been obtained. The iron concentrate obtained with 65.73% Fe and 0.23% S is a sort of high-quality iron-smelting raw material applied to the production of steel and iron smelting. Through the experimental study, the sulfur and iron resources in the pyrite ore have been recovered and utilized efficiently.

Jan 1, 2014

By Tingting Li, Guodong Li, Dezhou Wei, Cong Han, Shuling Gao, Yanbai Shen

"The aim of this study is to solve the problem of tungsten leaching from scheelite concentrate using sodium hydroxide in the presence of phosphate by an autoclaving process, which is one of main development techniques for tungsten recovery. To understand the applicability and leaching performance of tungsten leaching from scheelite concentrate, the main work is to investigate the effects of leaching parameters such as initial concentrations of NaOH and Na3PO4, reaction temperature, stirring speed, liquid-to-solid ratio and reaction time on WO3 dissolution rate to obtain the optimal leaching conditions. The chemical composition and phase composition of the samples were evaluated by means of XRF and XRD. The content of WO3 in the leaching residue obtained via washing, filtering and drying was analyzed by thiocyanate spectrometric method. The optimal leaching conditions were found to be NaOH concentration of 6.76 mol·L-1, Na3PO4 concentration of 1.35 mol·L-1, reaction temperature of 180°C, stirring speed of 400 rpm, liquid-to-solid ratio of 2.0 and reaction time of 90 min. The results showed that tungsten leaching rate of 99.20% was reached under the optimal conditions. The technology exhibited superior leaching performance, which not only reduced the consumption of sodium hydroxide but also greatly decreased reaction time in comparison to a conventional autoclaving process. INTRODUCTION Tungsten is an important strategic metal, which is widely utilized in a variety of industries due to its high melting point, superior mechanical properties and heat-resistant performance [1-3]. The chief raw materials for the production of tungsten in nature are wolframite and scheelite [4, 5]. Among them, approximately two-thirds of the tungsten reserves contain scheelite deposits in the world [6, 7]. With the progressive exhaustion of high-quality wolframite resources, scheelite has become a predominant primary resource for the production of tungsten [8, 9]."

Jan 1, 2018

By P. Fawell, C. Castillo, C. Ihle

"The need to reduce fresh water consumption has pushed many Chilean mining companies to utilize seawater obtained from distant locations. At the same time, increasing amounts of fine particles in copper tailings raise new operational challenges, in particular, the thickening and transport of tailings featuring significant fine fractions, which are predominantly clays. In the present paper, we study the role of salinity – using seawater and NaCl – on the flocculation efficiency of copper sulphide tailings to which kaolinite was added. To mimic the water recovery stage in thickeners, flocculation has been induced in jar tests and the corresponding aggregate size distribution has been estimated from chord length distribution data obtained using a focused beam reflectance measurement (FBRM) probe, at various mean turbulence intensities. Results show that for constant flocculant dosing, a measurable influence of the salt on the resulting aggregation exists. For each case, resulting optimal turbulence levels are also reported, a particularly interesting feature when comparing flocculation efficiency of the coarse and fine fraction. INTRODUCTION The concentration of copper minerals through comminution and flotation is intensive in the use of fresh water. The need to reduce the consumption of fresh water and the environmental standards associated with increasingly demanding mining operations have driven improvements in the techniques of recovering water from tailings. The challenges are even greater when required to treat minerals with high clay contents. In Chile, kaolinite is one of the most important clays to consider due to its abundance in the tailings from many operations. The most common and highest throughput unit operation in the mining industry for the recovery of water from tailings is gravity thickening, with sedimentation of fine particles assisted by flocculation. Flocculation is the process of forming aggregates by contacting the suspended particles with a flocculant. The flocculant is typically a water-soluble synthetic long-chain polymer, where copolymers of acrylamide and sodium acrylate are the most common types used in the Chilean mining industry. The aggregation mechanism includes the following key steps: (1) flocculant distribution through the suspended particles, (2) flocculant adsorption onto particle surfaces, and (3) collisions between particles leading to polymer bridging to form aggregates, but concurrently (4) breakage of aggregates becomes a factor under prolonged shear (Gregory, 1988)."

Jan 1, 2018

By B. P. von der Heyden, P. Neethling, M. Tadieb, L. Babedi

The effects of trace element substitutions in sphalerite mineral structure on optimised floatation response have, as yet, not been fully constrained or fully understood. To further this important field of study, this contribution focusses specifically on mineral and surface chemistry, and electro-chemistry of Cd- and Co- substituted synthetic sphalerites using Raman spectroscopy and Zeta potential experimentation. Raman spectroscopy illustrates that the presence of these impurities results in the introduction of a new mode, the relative intensity of which can be correlated (Cd r2=0.95 and Co r2= 0.99) to the dopant concentration. Comparison to X-ray Diffraction results measuring the unit cell parameter further shows that this relative intensity (Cd r2=0.81 and Co r2= 0.99) may provide insights into the degree of lattice strain within the mineral structure. The zeta potential distribution of an un-activated Cd-sphalerite show no detrimental effect as function of Cd content. Although the iso-electric point shifted from 2.45 at 1 wt.% Cd to 2.69 at 3.68 wt.% Cd, the zeta potential remained negative at alkaline media. Conversely, cobalt at low concentration of 0.36 wt.% had a detrimental effect on the surface charge, resulting to a close to neutral zeta potential at different pH. The adsorption of Cu ions on the surface of Co-bearing sphalerite conditioned in an alkaline media slightly increases the zeta potential of Co-sphalerite. While the Cd-bearing sphalerite decrease in negative zeta potential at >1 wt.% Cd indicating a complete exchange between Cu and Zn. The results presented herein illustrate that, based on the chemical nature of the substituting metal; sphalerite will exhibit multiple response to flotation reagents. Maximum recovery of zinc can thus only be achieved through multidisciplinary study and fundamental understanding of the effects of cation substitution on mineral structure and surface chemistry, the latter necessarily affecting the floatation response.

Jan 1, 2018