Search Documents

By T. ?kre, O. M. Dotterud, S. Haarberg, J. Thonstad, G. M. Haarberg

An electrowinning pilot plant has been constructed at Falconbridge Nikkelverk A/S, Kristiansand, Norway. The equipment consists of a mixing tank where the electrolyte composition and temperature are controlled, an electrowinning tank equipped with five cathodes and six anodes of commercial size and design and a dechlorination facility. Electrowinning experiments were carried out in this pilot plant using acid cobalt chloride solution from the cobalt tankhouse. Key parameters were varied to obtain an improved understanding of the cobalt electrowinning process, focusing on the detrimental deposition of cobalt oxide on dimensionally stable anodes. The extent of anode scaling was found to be dependent on the electrowinning conditions. Low pH, temperature and cobalt concentration resulted in less scale being formed, however at the expense of cobalt current efficiency and cell voltage, adversely affecting electrowinning production capacity and energy consumption. When operating at high acidity, pH in the anolyte was higher than in the catholyte, which is believed to be due to H+ ions taking part in the current transport across the diaphragm, migrating out of the bags surrounding each anode.

Jan 1, 2005

By Zygmunt Wegrzyk

Poland is rich in hard and brown coal reserves, which have become the most important, and steadily developing, primary source of energy. With 192.6 mill. t of hard coal production and 40 mill. t of exports in 1978, Poland is fourth and second in the world respectively. The paper discusses the various mining methods adopted in the country's history of mining. Particular emphasis is placed on longwails, their mechanization and equipment assembled in the form of fully mechanized face complexes suited for varied geological conditions. Measures to improve the recovery ratio of coal resources are dealt with. investment efforts undertaken in the coal industry are outlined. An account is given of the ever improving techno-economic results of coal mining. The country also exports a wide range of mining equipment and transfers its well-founded technical know-how to others. There are strong cooperative links with many foreign partners.

Jan 1, 1979

By Franco Chiesa, David Levasseur, Bernard Duchesne

A 500kg aluminium AlSi7Mg03 casting has been poured and the metallurgical quality at different locations inside the casting has been thoroughly investigated. It included measuring the local tensile properties (YS, UTS, El) in the T6 condition, the dendrite fineness (DAS) and the level of microporosity. A correlation was found between the microporosity level, the local solidification time and solidus front velocity; this correlation allows to predict the porosity level in large aluminium castings (solidification times between 20 and 200 minutes). Quite expectedly, properties varied widely within the casting and the actual mechanical properties were much less than the "textbook values" based on measurements carried out on separately cast standard specimens. A correlation between the secondary dendrite arm spacing (DAS) and the local solidification time was in keeping with previously published data. Finally the conditions to obtain an acceptable finish on machined surface were determined.

Jan 1, 2014

An optimized long-term mine planning determines the best order of material extraction, so that the Net Present Value (NPV) becomes maximum. In the case of oil sands surface mining, one of the key constraints in NPV maximization is the volume of tailings slurry that will be generated downstream. Specifications of tailings slurry are also important from environmental perspective. Moreover, most of the material that will be used for the reclamation of tailings ponds in later periods is generated in extraction and processing of oil sands. In this paper, an integrated optimization framework is proposed to maximize the NPV of the produced oil sands, with respect to tailings capacity constraints and reclamation material requirements. A mixed integer linear programming (MILP) model is developed to find the optimal solution for long-term mine planning problem. The proposed model is coded in Matlab and has been run using CPLEX for verification. The results for real-case oil sands dataset show that the optimal production schedule meets material requirements for reclamation, tailings volume is within tailings capacity range in all periods and the production schedule follows the predetermined horizontal direction.

Aug 1, 2013

By Rashid Bashir

Shaft sinking through solid rock, which contains little or no water, poses little difficulty. However, when loose, water-bearing strata have to be contended with, water control measures, and pumping facilities are needed. Shaft sinking in Athabasca Basin requires sinking through water bearing sandstone which can be highly fractured. Intersection of local zones of extensive fracturing results in the potential for high water inflows with pressures up to 5 Mpa. Grouting is carried out ahead of each shaft sinking interval as water control strategy. In the grouting method, liquid cement is forced into the water-bearing earth under very high pressure. Shaft sinking performance which can be quantified in terms of rate of advance is highly dependent on the days spent at each interval grouting before sinking can advance to the next interval. This paper presents the shaft sinking experience in Athabasca basin and how some of this is translated into Geoscientific Investigations for Future Shafts. A comparison of Geoscientific data collected from future shafts at McArthur River and Millennium Mines is compared to historical data collected from pilot holes, where shafts have already been sunk. The paper concludes with the strategies for better integration of hydrogeological, geotechnical and geophysical data.

Aug 1, 2010

"The Schist Lake mine, owned and operated by the Hudson Bay Mining and Smelting Co., Limited, is situated on the northwest arm of Schist Lake, 4 miles southeast of Flin Flon, Manitoba.The deposit was discovered early in 1947, during a diamond drilling program exploring small copper showings along the west shore of the lake. The orebodies came to surface between the mainland and the north end of Stitt Island.Production began in August, 1954, at an initial rate of 300 tons per day. Underground workings have been carried to the 1,700-foot level, where exploration work is now being done.General GeologyRocks of the area are Precambrian lava flows, with associated pyroclastic breccias and tuffs, and related minor intrusions. Their general strike is northwest and their dip is nearly vertical. Shearing is common and is related to the activity which caused intense folding and much faulting in the area. The larger faults and the fold axes trend a few degrees west of north. The lavas are mainly andesitic but a layer of sericite-carbonate schist, which is probably derived from a fine-grained, grey quartz porphyry, occupies most of Stitt Island and extends into the mine area. It is within this layer of schist that the ore deposit occurs (Figure 1).The OrebodiesThe ore occurs as tabular to lens-shaped bodies which strike northwest, dip nearly vertically, and plunge at 60 degrees to the southeast. The ore zone is 800 feet long and has been traced for a distance of 2,000 feet along the plunge (Figure 2). The maximum length of continuous ore within this zone is 200 feet. Widths of individual ore lenses vary from a maximum of 35 feet to a minimum of 2 feet.The ore consists of three distinct types: massive sphalerite-pyrite, massive chalcopyrite-sphalerite, and disseminated chalcopyrite-pyrite. The No. 1, or eastern, orebody is predominantly massive sphalerite-pyrite. The western part of the No. 2 orebody is massive chalcopyrite-sphalerite. The disseminated ore forms the eastern part and the lower end of the No. 2 orebody. All three types of ore, with patchy distribution, are found in the smaller lenses below the 1, 100-foot level.Metallic minerals, in order of deposition, are pyrite, arsenopyrite, chalcopyrite and sphalerite, galena, enargite, and gold. Both massive types of ore exhibit banding in many places, probably as a result of the selective replacement of schist. The disseminated ore was formed as a filling of the interstices in a brittle chert rock which appears to have been crushed by the same forces which produced the schist."

Jan 1, 1949

By T. C. Chudy, C. C. Hamilton, G. R. Lane

The selection and provision of mineralogical services to assist in developing a GeoMetallurgical program for a Cu Porphyry Mine in South America is covered in this paper and presentation. The objectives of the study were to provide a rapid mineralogical scoping protocol to support and confirm results of sequential Cu leach data and to provide detailed mineralogical analysis of four composites and products on which locked cycle test-work were performed. Results showed good reconciliation was achieved between measured chalcopyrite and secondary Cu mineral contents with leach data using a linear intercept mineralogical procedure by TIMA (Tescan Integrated Mineral Analyser), as well as a generally positive correlation between pyrite and Cu-sulphide grain size. Size-by-size analysis of Composite feeds and test products was used to outline comparisons between feeds on a mineralogical basis and provide liberation and association data with which to diagnose and better explain performance. Identifying key mineralogical drivers to Cu recovery and concentrate grades using these results, a greater understanding of the role of chalcocite and pyrite on metallurgical performance was established. INTRODUCTION As a global supply of copper, porphyry copper deposits are typically very large, often in excess of a billion tons of ore (Keeney, Walters, & Kojovic, 2011; McMillan & Panteleyev, 1980) with grades typically between 0.2 and 1.2% Cu, and up to 2% Cu in places. They are also a source of gold. The complexity of copper porphyries arises from their classically zoned nature, the type of host rock, as well as whether or not they have been overprinted by oxidation, weathering and supergene enrichment (Sillitoe, 2011). Zones of alteration and other geological attributes give rise to varied mineralogy, ore mineral textures and material properties, all of which result in different processing characteristics. Due to the interdependencies of geological and processing characteristics, it is vital to study links between the geology at the macro-scale and mineralogical features down to millimeter and micrometer scale (mineral content and texture) and their influences on mineral processing behaviour (Cropp, Goodall, & Bradshaw, 2013). The growing field of GeoMetallurgy aims to provide an Orebody Knowledge framework by which to gather such information as it pertains to: (1) Understanding and predicting likely flotation response; (2) Guiding relevant test work to investigate and validate links, interdependencies, theories and data interpretation/evaluation; (3) Populate a block model with relevant information and; (4) Implement and refine the model for ongoing optimization and control. Specific questions addressed by using mineralogy often include flotation diagnostics as aids to interpretation, causes of dilution and losses to tailings, as well as guidance to sampling for test work (Cropp et al., 2013).

Jan 1, 2019

By M. Silva, G. Olivares

In a leach pile, the drainage layer or commonly known as the cover layer has been a matter of discussion due to the multiple phenomena or events that occur within it which impacts negatively the leaching process. All these events are directly related to the loss of draining capacity and irregular flow net due to an excessive compaction and entrapment of fines reducing the flow velocity which in turn cause more fines to get trapped. Over time the problem will continue to worsen rapidly and accelerating continuously like a geometric progression. When the cover layer gets to a certain level of deterioration, the only alternative to continue operating safely is to replace the entire cover material, a huge cost for any mining operation. TESRA has developed a solution to counteract the accelerated advance of the deterioration of the drainage layer. The solution consists of using large agricultural tractors coupled to a proprietary design of a heavy- duty subsoiler-ripper for deep tillage for loosening and breaking up the ground at various depth and with different legs spacing from 0.4 m or above. Also, if the ground still requires additional breaking, TESRA proposes the use of a rototiller that breaks any lumps to homogenize the ground to a certain particle size. With the subsoiler-ripper/rototiller combination equipment a layer of 0.5 m deep is properly treated to match closely the original conditions of the ground thus regaining the flow net as close as to the original seepage condition. Once the ripping is completed the subsoiler-ripper tool is replaced with another that is similar to a plow and thus continue with the installation of drainage pipes. The tool digs a Y-type profile trench allowing the pipe to sit precisely at the bottom of the trench, contributing additional lateral and lower support. This tool controls the installation depth of the drainage pipe at different inclination grades and also eliminating any irregularities that may block the flow of the leaching solution. Sometimes the obstructions block completely the flow of the solution. The main result of this methodology is the reduction of groundwater levels and at least 2% less humidity in the leaching gravel due to an increase in the draining capacity of cover. The methodology developed by TESRA applied during a couple of cycles of a dynamic leach pile has proven to be a real alternative to remedy and recuperate the cover close to its original conditions. The methodology requires only one large tractor and two accessories operated in different stages while replacing the more traditional and less efficient machinery such as the Bulldozer, Motor-grader, and backhoes.

Jan 1, 2019

By P. C. Patnaik

Performance of industrial gas turbine engines in terms of power output, reduced cooling and efficiency have been continuously increasing in parallel with aero gas turbines due to the advances made in the development of new materials, protective thermal barrier coatings (TBCs) and the advanced diagnostics to monitor service induced problems such as hot corrosion, thermal and thermo-mechanical fatigue and other operational issues, Environmental attack (hot corrosion or high temperature oxidation) is a common degradation mode in the hot section of the gas turbine, Hot corrosion occurs when Na or K bearing compounds in the environment or in the fuel combine with other contaminants such as S and Pb or V to form corrosive sulphates or vanadates thus attacking the protective oxide on the turbine airfoil, These problems pose far more threat to new turbine engine materials such as directional solidified, single crystals and ceramic matrix composites (CMCs). The CMCs due to their increased temperature capability, when used in the combustion chamber, are likely to reduce the peak temperatures attained during combustion and therefore provide the benefits of reduced emissions of oxides of C and N, These issues will be reviewed critically and their impact will be assessed on gas turbine lives. With respect to alternate fuels, past experience has shown that utilization of residual oils and coal derived fuels in gas turbines have resulted in complex deposition and corrosion processes, In recent years biomass derived alternate fuels have been used either through a gasification cycle or through direct firing of the biomass derived liquid fuel with a view to reduce Green House Gases (GHGs) and improve the climatic conditions. In both cases, the resulting high temperature corrosion processes (in the presence of alkaloids in the fuel) are also very complex, leading to premature removal of hot section components, Technology solutions mitigating these fundamental problems will be reviewed and solutions presented.

Jan 1, 2005

By F. A. Charalambous

Brannerite is commonly referred to as a refractory uranium mineral as it is usually highly resistant to acid leaching. There is however widely varying literature data on brannerite leaching, with some studies reporting that brannerite leaching can be achieved under relatively mild conditions. The differences observed for brannerite leaching are most likely due to the high degree of variation in the composition and structure observed in natural brannerites. These aspects of brannerite chemistry however are not very well understood due to a lack of fundamental research. The aims of this study were to investigate and develop methods for synthesising brannerites of varying composition and to investigate the effects of composition on brannerite leaching in acidic conditions.

Aug 1, 2010

By I. A. Menshikh, S. A. Kotov, N. L. Shinkarkin

All the cycle for conversion of natural and reprocessed uranium of ROSATOM’s “TVEL” Fuel Company is concentrated at the Siberian Chemical Plant. Conversion capacities are located on two sites, i.e. the Radiochemical Plant, which refines feedstock, and the Conversion Plant, which produces uranium oxides and uranium hexafluoride. Liquid radioactive waste arising in the process, after pretreatment, is transferred to a dedicated national operator for underground disposal. Environmental strategies pursued by the Fuel Company involve the introduction of process solutions intended to eliminate liquid radioactive waste and convert it into a solid phase. In the 5–7 years coming, work will be performed to refurbish and upgrade conversion facilities of the Siberian Chemical Plant that will principally change its radioactive waste management scheme. This paper describes the current waste management scheme and sets out planned schemes for management of natural and reprocessed uranium waste, which will be implemented in the refurbishment of conversion facilities of the Siberian Chemical Plant. The new technologies for the management of liquid radioactive waste from uranium conversion described in the present paper have an undeniable advantage over the current technology mainly due to significantly less environmental harm.

Jan 1, 2020

By Y. Thibault, G. Deschênes

An open-pit mine, located in Mexico, processes an ore a rate of 4000 tpd, using conventional cyanidation and AYR. A laboratory study was conducted to increase silver extraction and to reduce the concentration of cyanide in leaching. The sample contained 0.41 g/t Au, 125 g/t Ag, 99% gangue minerals, 0.7% pyrite, 0.07% sphalerite, 0.03% chalcocite. Silver was present as acanthite, stromeyerite, silver mercury/halogen, silver with copper in solid solution and jalpaite. The plant conditions (2400 ppm NaCN) produced 90.2% gold extraction (residue at 0.04 g/t Au) and 92.7% silver extraction (leach residue at 9.1 g/t Ag). The CELP (CANMET Enhanced Leaching Process) produced 97.0% silver extraction (residue at 3.8 g/t) and 90.2% gold extraction using 500 ppm NaCN. The incremental gross revenue was estimated at $US7.6 million and the reduction of cyanide costs was $2.9 million per year (79%).

Jan 1, 2011

By Kimberly Morrison

Strategically located within the Uravan Mineral Belt District of western Colorado, the Piñon Ridge Project is the first new uranium mill being proposed for construction in the United States in over 25 years. In 1992, dramatic changes to the US regulatory environment for uranium ore processing occurred making regulatory compliance an increased challenge for a new facility. Proposed as a 6.3 million tonne uranium milling operation, the mill will receive ore from a number of mines in the region. The project includes design and permitting of a uranium/vanadium processing facility, tailings cells, evaporation ponds, and ore stockpile pads. The focus of this paper is to provide an overview of the US regulations and how these regulations were applied to design of the mill facilities, as well as provide a status update on the project as the mill license application was submitted to the Colorado Department of Public Health and Environment (CDPHE) in November 2009.

Aug 1, 2010

By Eugene Sun, Qiang Xu

This presentation will review current applications of composite materials in aircraft design and discuss the challenges involved in maximizing the potential of the composites in aircraft applications.

Jan 1, 2010

By D. Sammut, F. Houllis, J-L. Huens, J. Moyes

The Intec Gold Process has been developed as a halide-based alternative for the recovery of gold from refractory sulphide deposits. The halide medium allows sulphide oxidation and gold extraction to be performed concurrently at moderate temperature and atmospheric pressure sourcing oxygen from direct air injection. The dissolved gold is loaded onto activated carbon and stripped in a conventional Zadra circuit. High gold extractions have been achieved from a range of refractory gold concentrates at laboratory scale, which has led to a continuous locked-cycle pilot plant program. The pilot plant operated at >99% availability, with a maximum of 96.5% gold extraction from a concentrate containing 58.6 g/t gold. >99% of the dissolved gold was loaded onto carbon at up to 1% w/w, with no loss of carbon activity detected over five loading/washing/elution cycles. This paper describes the process and presents both laboratory and pilot plant results as well as economic data from two costing studies.

Jan 1, 2005

By B. Schulz, T. Leißner, R. G. Merker

"Ores enriched in critical rare earth elements (CREE) keep on being of particular interest. The CREE are Nd, Eu, Tb, Dy, including Y. In conjunction with beneficiation tests on Y-mineral bearing flotation tailings of complicated mineralogy, the Mineral Liberation Analyses (MLA) was used to work out processing characteristics fraction-wise in terms of modal mineralogy, mineral recovery, locking and liberation, and particle size.Size fractions from mechanical sieving (“real fractions”) as well as fractions created virtually by using filters on the MLA-data of the unsieved head material (“virtual fractions”) were investigated comparatively thereby. The ""virtual-sizing-approach"" features a much simpler sample preparation procedure and considerably lower cost if a fraction-wise investigation of a head sample is needed. It can be conveniently applied to intimately locked ores needing a fine grinding to a particle size distribution (PSD) range below 25 microns for instance. However, its practical use is sometimes disputed in terms of the reliability of the results. Results are shown for the main Y-bearing mineral xenotime and selected main gangue minerals of a low grade REE-ore.The influence of sample representativeness, sample preparation and particle counting statistics turned out to be of crucial importance. Given that all preconditions for reliable results are met, locking characteristics, modal mineralogy, and even PSD trends can be read from virtual fractions.The authors encourage processing engineers to use the virtual approach. They propose practical measures to improve the reliability of the MLA results, identify and tackle conflicting results, and mitigate evaluation problems that may arise."

Jan 1, 2016

By P. J. Foster

Bowtie analysis has recently emerged as a technique of choice that can be used when looking specifically at major hazards in the mining industry. A Bowtie diagram is a graphical means of assessment that focuses on identifying all the specific causes and consequences of major events, from which all the ?pre-event? and ?post-event? control measures can be identified. From this critical control measures can be identified and monitoring/assurance systems can be established. It is this assessment of control measures and their effectiveness that replaces the more traditional evaluation of risk (using matrix-based approaches) based on the fact that risk is a function of control ineffectiveness. This is a major difference with traditional risk assessment where all too often control effectiveness is assumed. This paper summarises the Bowtie analysis process and outlines one specific case study where the technique was used on the unwanted event of a collision of a haul truck and light vehicle in an openpit mine. Although more effort is required in undertaking the assessments, control assurance provided this way will go a long way in ensuring that risk assessments and major hazard management become much more effective in practice.

Aug 1, 2013

In the leaching and recovery of gold from copper containing gold ores using cyanidation, some copper minerals also dissolve which can have a detrimental effect on the process efficiency and economics. There are also environmental concerns with current operations discharging cyanide and copper cyanide species into tailings dams, and strict regulations prohibit this for greenfield plants. Cyanide destruction however is not an economic option for new plants treating copper-gold ores. This paper evaluates a potential recovery process to overcome the copper cyanide problem. Despite gold dissolution occurring in copper cyanide solutions having no free cyanide, gold recovery from ores is lower compared to free cyanide. Thus, cyanide addition has to be optimised to maximise the gold recovery whilst endeavouring to eliminate free cyanide at the completion of leaching (CN:Cu less than 3:1). Subsequently, copper cyanide can be recovered using activated carbon. The loaded copper cyanide is easily recovered from the carbon with a cyanide soak and distilled water wash such that the eluted CN :Cu ratio is less than 4:1. The copper could be recovered efficiently by electrowinning, by decreasing the pH of the eluant to 5. The remaining cyanide solution, after electrowinning, is then neutralised to form NaCN and recycled.

Jan 1, 2005

By P. Homola, M. Karlík, M. Slámová

"Aluminum sheets (AA1199, AA8006, and AA5754) were processed by accumulative roll-bonding (ARB) in the temperature range from 20 to 350°C. The microstructure of the sheets was characterized by means of scanning and transmission electron microscopy and electron backscattered diffraction. Mechanical properties were monitored by hardness measurements and tensile tests. Increasing strain (number of ARB cycles) led to incremental development of lamellar microstructure with a decrease of the spacing between high-angle grain boundaries in the normal direction of sheets. ARB process produced an important increase of strength while maintaining thickness and relatively high ductility, without accenting of the anisotropy of mechanical properties of sheets. The level of hardening decreased with the processing temperature and at 300 and 350°C ARB caused even the softening of the material due to the recovery of the deformed microstructure or partial recrystallization during heating to ARB processing temperature.INTRODUCTION Accumulative Roll Bonding (ARB) is a technique of grain refinement by severe plastic deformation (SPD) proposed by Saito et al. (1999). One ARB cycle consists in sheet cutting, surface treatment, stacking of two pieces, heating (optional), and rolling with 50% reduction in thickness. Since the sheet thickness remains unchanged by this cycle, ARB processing can be repeated as many times as desired. The goal of ARB is to impose an extremely high plastic strain on the material, resulting in structural refinement and strength increase without changing specimen dimensions. After several cycles, ultra-fine grained (UFG) materials with high strength and relatively high ductility are produced. An advantage of this method is that it does not require any special equipment as other SPD methods such as equal channel angular pressing (ECAP) (Valiev & Langdon, 2006), high pressure torsion (HPT) (Valiev et al., 2000), or cyclic extrusion and compression (CEC) (Richert et al., 1999), but only a conventional rolling mill and so it is seen as an economically viable and industrially scalable processing route. ARB processing has been successfully applied to various kinds of metallic materials at room or elevated temperatures (Tsuji, 2005). Besides processing single metals and alloys, ARB has also been used for creating ultra-fine grained and nanograined metallic composites (Wu et al., 2010; Qu et al., 2014)."

Jan 1, 2018

By N. Djilali

Many of the transport phenomena encountered in proton exchange membrane fuel cells occur intrinsically at the microscale level. Physically representative models that fully account for the salient physico-chemical and transport processes in PEM fuel cells are necessary to achieve truly predictive models that can be used with confidence to: (i) gain a better understanding of in-situ processes and couplings, (ii) explore new concepts, and (iii) support design and optimization. The development of more general, rationally based macroscale models requires use of knowledge on the microscale level to provide guidance, and to determine the required parameters and coefficients (model "constants"). In this paper we present a new membrane transport model, the binary friction membrane model (BFM2), recently developed to account for coupled protonic and water transport in polymer membranes. This general model is based on rational and physical consideration, removes several of the limitations of the empirical models used to date, and is formulated for all purfluoro-sulfonic acid membranes. The use of the BFM2 in a fuel cell model is illustrated highlighting significant performance predictions compared to existing empirical model. The second part of the paper addresses the fundamentals of two-phase transport in hydrophobic gad diffusion media. Computational and experimental visualizations resolving the microscale dynamics of water transport between the fibres of a GDL are presented, revealing transport mechanisms that are, contrary to assumptions used to date, dominated by fingering and channeling.

Jan 1, 2005