Search Documents

By A. C. Gagnon, H. Saroglou

"The focus of this paper is on the analysis of geometrical discontinuity properties for the rock mass located within an open pit mine located in Western Africa. Discontinuity data were collected using various techniques including oriented core logging, borehole televiewer surveys, surface pit wall mapping and photogrammetry. The geological setting was initially studied prior to the data analysis to produce threedimensional ground models of the regional and mine site geology along with block diagrams illustrating predicted fracture patterns. Stereographic and statistical discontinuity data analysis of the geometrical properties of the rock mass was subsequently performed to identify unique structural domains throughout the open pit area. The discontinuity data collected throughout the studied open pit area were primarily discontinuity orientation, frequency and spacing and the investigation focused on the reasons for observed differences between the various data collection techniques. Stereographic analysis was used to assess the preferred geometry of discontinuities filtered by lithology, data collection technique, borehole, discontinuity type and pit wall (footwall or hanging wall). The observed fracture pattern is explained adequately by the geological setting. The need for accurate ground models for the design of open pit slopes is highlighted.INTRODUCTIONThe Tasiast Mine is an open pit operation located in north-western Mauritania, approximately 300 kilometres north of the capital Nouakchott. The Tasiast mine, which is owned and operated by Kinross Gold Corporation (Kinross), began commercial operations in 2008. The Tasiast mine is located in an area characterized by flat desert terrain within the western reaches of the Sahara Desert region. The current mine site includes mill buildings, shop facilities, waste dumps, tailings facilities and two main open pit operations (Piment and West Branch). The West Branch pit is the focus of this paper. The current open pit plan for West Branch indicates a final pit measuring approximately 2.5 km long by 1.4 km wide and 510 m deep."

Jan 1, 2015

By Sunil S. Gandhi

"The Mountain Lake deposit is a tabular sandstone-type uranium deposit, hosted by the basal unit of Middle Proterozoic Dismal Lakes Group. Uranium occurs mainly as sooty pitchblende disseminated in stratiform lenses within gently dipping quartzose sandstone. It is associated with copper sulphides, pyrite, hematite, and traces of nickel and cobalt arsenides and of silver.Exploration HistoryUranium showings on the PEC claim group were discovered during 1969 by an airborne radiometric survey carried out over the Dismal Lakes-Great Bear Lake area by Aquitaine of Canada Limited (Bizard and Salat, 1969). Some drilling was done in the vicinity of the showings in 1975 by the company under a joint venture with Eldorado Nuclear Limited but the results were not encouraging (Hassard and Woollett, 1975). During 1972, Trigg, Woollett and Associates Limited conducting surveys for Imperial Oil Limited, discovered numerous high-grade radioactive boulders scattered over a distance of several kilometres north and west of the showings, and the area north of the PEC claims was staked as the YUK claims (Ahuja, 1974). A systematic study of the boulder distribution and Pleistocene geology suggested a source additional to the showings. More intensive exploration followed, and in 1976 drilling just north of the PEC claim group boundary intersected the main deposit at a depth of 75 m to 150 m, beneath overburden up to 60 m thick. Part of the deposit extends into the PEC claim group which is under exploration by the Aquitaine-Cominco Joint Venture.The following brief description is based on the presentations in 1978 by F. Hassard of Trigg, Woollett and Associates Limited at the Geoscience Forum in Yellowknife, and by S.S. Gandhi of the Geological Survey of Canada at the Mineralogical Association of Canada Uranium Short Course in Toronto."

Jan 1, 1986

By J. Karonen, M. Tiihonen, J. Guentner, L. Haavanlammi, Outotec GmbH, E. Kolehmainen

"Rare earth elements have obtained significant attention during the last few years due to predicted increase in their demand. Several projects worldwide are at pre-feasibility or feasibility stage aiming to commence production. Deposits of rare earth elements are typically complex and multi-metallic of nature. This means that production processes are often also complex and therefore, various metallurgical unit processes are needed. Outotec’s equipment and technology portfolio is very comprehensive and includes hydrometallurgical and pyrometallurgical apparatus and processes applicable to the efficient exploitation of rare earth deposits. Outotec has gained useful experience relevant to the processing of rare earths through several assignments including those for Alkane Resources Ltd. (Dubbo Zirconia Project), Greenland Minerals and Energy Ltd (Kvanefjeld Project), Frontier Rare Earths Limited (Zandkopsdrift project), Tantalus Rare Earths AG (Madagascar), Quest Rare Metals (Strange Lake project) and Orbite Aluminae Inc. (HPA project). The hydrometallurgical test work of two process flowsheets is presented in the paper. A roasting or acid baking step is common to several proposed rare earth projects. In the past, rotary kilns have been used, but Outotec has developed a new process concept to handle the rare earth material in fluid bed reactors. The basis for this development is long experience in fluid bed technology of Outotec in Germany. One advantage of fluid bed roasting is the higher throughput per unit. In combination with the roasting and baking, Outotec offers the gas cleaning and acid plant and provides a complete and closed concept.INTRODUCTIONRecovery of rare earth elements (REE) has obtained significant attention during recent years. It has been estimated that their demand will be boosted because of their need in many technology areas. REE can be utilized in magnets, batteries, displays, catalysts, optical devices etc. (Jordens, Cheng, & Waters, 2013; Zhang & Edwards, 2013). The production of REE is focused in China, which means that production outside of China is very scarce. However, there are multiple active development projects worldwide working towards production of REE containing products outside of China (Chen, 2011)."

Jan 1, 2016

By Cheryl L. Allen

The increasing energy costs associated with mining has become an issue that needs to be addressed for future sustainable production. Vale Inco is undertaking a Ventilation on Demand (VOD) Project in an effort to minimize costs, continue to mine at depth and reduce green house gas emissions. A dynamic VOD system is very complex with potential high risk. Therefore, a systematic approach is being taken for successful development and implementation of the concept. The physical components of the system are currently being tested at various Vale Inco mine sites. While the operability of the physical components are being tested, the strategy for optimizing the architectures of the system is being defined. This presentation discusses the method of developing a VOD system at Vale Inco.

Feb 1, 2008

By M. S. Moats, F. Elnathan

"The effect of current reversal on two commercially manufactured electrodes (RuO2-TiO2 and IrO2-Ta2O5 coated Ti) in a chloride bearing electrolyte was evaluated. Accelerated lifetimes were found to decrease with increasing current density and increasing reversal frequency. Ru: Ti coated electrodes exhibited longer lifetimes than Ir: Ta coated electrodes even though they had one-third as much precious metal content. Chloride concentration did not affect lifetime in the range examined. Using energy dispersive X-ray spectroscopy (EDS), scanning electron microscopy (SEM) and electrochemical impedance spectroscopy (EIS), the failure mode of the electrodes was determined to be coating dissolution leading ultimately to passivation by the presumed growth of a highly resistive oxide at the coating/substrate interface.INTRODUCTIONCatalytic titanium anodes (CTAs) were developed in the 1960’s to replace graphite anodes in chlor-alkali cells. CTAs exhibited much better dimensional stability than graphite leading to lower operating potentials by promoting smaller electrode gaps and better operational efficiencies as they had to be replaced less often. CTAs are simply Ti substrates coated with precious metal oxides (such as IrO2 and RuO2) mixed with other components (such as TiO2 and TasO5) (Trasatti, 2000).CTAs are used in many other electrochemical industries, including water disinfection, wastewater treatment, cathodic protection and metal plating. RuO2 based coatings are typically used for chlorine evolution. IrO2 based coatings are for the most part utilized for oxygen evolution (Comninellis & Nerini, 1991; Forti, Olive, & De Andrade, 2001; Kotz, Stucki & Carcer, 1991; Trasatti & Lodi, 1981)"

Jan 1, 2016

By G. W. Zhang, Changsha Research Institute of Mining and Metallurgy, X. Xiao, Y. Long, L. L. Huang

"The paper presents a scale-up and design method of vertical screw stirred mill, in which the closed circuit of mill and hydrocyclone was assumed as one factor, theoretically regardless the affects inside system of the mill and hydrocylone. The specific energy is chosen as a scale-up criterion, based on the premise that when fed the same feed material, mills of different sizes delivering the same specific energy will yield products.Batch grinding tests are conducted to determine the specific energy, and combined with industrial production data, scale-up and design of vertical screw stirred mill for industrial production are accomplished. Having developed this method for the vertical screw stirred mill used in regrinding duty of iron ore in Ma Steel, it has now been successfully applied in other installations.INTRODUCTIONThe Towermill was developed in Japan in the 1950s, by the Tower Mill Kubota Corporation, it was fine and ultra-fine grinding mill of the metallic ores and concentrates. Due to the rapid development of metal mining and useful minerals disseminated fine, fine grinding and ultrafine grinding equipment has also been more wide used in minerals processing industry. Typical fine and ultra-fine grinding mil are the Vertimill and Stirred Media Detritor (SMD) Mill of Metso, Eirich Towemill, Outotec HIGmill, FLSmidth VXPmill, Xstrata Isamill and the vertical screw stirred mill (JM) of CRIMM, etc.JM series of vertical screw stirred mill were invented by Changsha Research Institute of Mining and Metallurgy in the 1980s. Energy saving and consumption reducing have been achieved through the optimization and engineering practice. More than 500 units JM series of vertical screw stirred mill are used in the iron ore, copper ore, copper-molybdenum ore, molybdenum ore, Pb-Zn ore and Au ore."

Jan 1, 2016

By H. A. Wentworth

The Central Manitoba mining district, as spoken of in Manitoba, refers to that portion of the country lying between lake Winnipeg on the west and the Ontario boundary on the east, and from a few miles north of the Wanipigow (or Hole) river on the north, to a few miles south of the Bird river. It embraces two known mineralized belts; the gold area in the north, extending from the shores of lake Winnipeg almost to the Ontario boundary (in a slightly southeasterly direction) a zone some eight or ten miles wide and perhaps forty miles long, lying (for the most part) north, and parallel to, the Manigotagan river; and the Bird river copper and coppernickel deposits, an area not yet clearly defined, but in general lying immediately north of, and roughly parallel to, the Bird river. To the south of the Bird river is a somewhat differently mineralized area, numerous pegmatite dykes being found, with minerals typically associated with such rocks. More specifically, the known gold deposits are largely segregated in the above belt; (1) around English brook; (2) along the north shore of Wanipigow lake; the Rice lake area (about midway of the belt); and the Long Lake-Bulldog lake area, at the eastern end of the belt. Not all the known gold occurences are found in these segregations, but the density of claim staking in these areas is perhaps an indication of the greater number of prospects found in them to date.

Jan 1, 1925

By W. L. Stuewe

For the purpose of this paper I shall, in order to limit myself, define the words 'Maintenance' and 'Equipment' as follows: Maintenance shall mean the 'care of or 'the sustaining of equipment in as nearly perfect condition as possible. Equipment shall mean any item of a mechanical nature entering into the production of coal; it will be seen that unless one limits the use of this word it could take in administration as well as operative equipment, and include metal mines, mills and smelters, and manufacturing plants. In any industry the first consideration is the proper operation of all units entering into the production of the article manufactured or produced. I wish to quote here what a man, well known internationally in financial circles, told his operators at the time a large expansion programme was under consideration. His exact words were: "I do not care how much it is going to cost. What I want to know is how much it is going to cost to operate and maintain. It is the continuous drain for repairs that costs us the most money." The truth of this statement has been proved time and again, and many companies have found the cost of maintenance to be the balance between profit and loss-so much so that, in two instances with which the writer is familiar, the mechanical equipment was practically replaced throughout. I bring this point out here to emphasize the value and necessity of keeping abreast of the times, and obtaining maximum efficiency with the minimum outlay. Time is indeed money where delays occur due to defective or poorly kept equipment, and it is absolutely necessary to prevent machinery from becoming defective or inefficient.

Jan 1, 1930

By Takao Oishi, Go Ohara, Toru Kitazaki, Masahiro Tanaka

"The High Pressure Acid Leach (HPAL) plant for nickel-cobalt mixed sulphide production at Coral Bay Nickel Corporation (CBNC) in the Philippines has been in operation since 2005 with a capacity of 10,000 t/year of nickel. Subsequent to the commissioning of the second plant in 2008, the production capacity increased to 22,000 t/year of nickel (Llerin et al., 2011). CBNC’s annual nickel production reached more than 24,000 tons of nickel in 2014. The concepts to achieve this capacity are the high availability and the reciprocally flexible operation of both plants. The availability depends on some factors, such as the control of impurities in the process and the equipment condition, to mention a few. In the HPAL process, it is not only the autoclave operating conditions that affect nickel extraction but also the impurities in the ore greatly influence it. The major element in the ore is iron and most of this iron is precipitated as Fe2O3, while the rest remains as Fe2+ or Fe3+ sulphate in solution. These ions in solution reduce the availability, so it is important to control the formation of iron ions by controlling the impurities in feed ore as well as the HPAL conditions. This paper presents the general HPAL process and the behaviour of impurities, focusing on iron behaviour in the HPAL process.INTRODUCTIONCoral Bay Nickel Corporation ProfileCoral Bay Nickel Corporation (CBNC) was founded on April 2002, as a joint venture of four companies; namely, Mitsui Corporation (18%), Sojitz Corporation (18%), Nickel Asia Corporation (10%) and Sumitomo Metal Mining Corporation (SMM) with a controlling stake of 54%. Aside from its capital share, Nickel Asia Corporation also supplies the ore and limestone for the High Pressure Acid Leach (HPAL) plant located in Rio Tuba, Philippines, as shown in Figure 1 (Tsuchida, 2008). The objective of the CBNC project is to produce 22,000 t/year (original design) of nickel and 1,500 t/year of cobalt, as sulphide, by the treatment of nickel laterite ore which is a low grade nickel oxide ore in the Philippines (Mines and Geosciences Bureau, 2014). The sulphide product has been exported as a raw material to the SMM Nickel Refinery in Japan for 30 years. The product of this plant, a mixed (Ni/Co) sulphide, is shipped to the SMM’s Nickel Refinery in Niihama, Japan. SMM Corporation provides the technology and management personnel to the plant. SMM Corporation also supplies the sulphuric acid, which is the main reagent for the HPAL process."

Jan 1, 2016

By J. Huh

Recently, there is growing trend to build the high-rise and install curtain walls. Following this trend, we developed robot for building wall cleaning work, which moves along Built-in guide rail of building. Because it moves attached at building wall for cleaning work, it can be seriously affected by potential threats, like earthquake, strong wind, malfunction, and construction error of built-in guide rail. In order to cope with those threats actively, this paper presents the Fail-Safety system. The building wall cleaning robot consists of two moving system: The Horizontal Moving System which mainly do maintenance work, and The Vertical Climbing System which transport the horizontal moving system floor by floor. We apply the Fail-Safety system to these systems. The Fail-Safety system consists of sensors to detect external situation, and, with information of sensors, give instruction for what to do. This robot system is installed with four kinds of sensors: shock sensor, infrared ray sensor, laser sensor, magnetic sensor. First, shock sensor detects external shock during cleaning work. When shock sensor detects big shock, the robot returns to starting point to inspect how damaged it is. Second, infrared ray sensor detects damage of built-in guide rail. It is to prevent destruction of robot caused by moving along damaged rail. Third, laser sensor gives notice about where obstacle is. It is for robot to avoid crash with obstacle and decrease damage. Fourth, magnetic sensor detects magnetic points, which are installed in rail at regular intervals, and helps robot to find its position, based on location of magnetic points detected. If robot is damaged by external shock and its encoder, which gives information of location to it, is not working, magnetic sensor will give information of robot?s location to robot. And then, robot regulates its velocity depending on position of it, and safely returns to starting point. The Fail-Safety system in this paper is for building wall cleaning robot to sense external threats, and prevent getting worse. Applied to this active protection system, making safe environment of maintenance work is possible for robot system.

Aug 1, 2013

By S. Fabich

Since the very beginning of Polish copper mining, special consideration of sink shaft techniques through highly saturated Cenozoic rocks was required. Shaft freezing has been chosen as a method to consolidate these rocks. Due to the rock mass structure and water inflow potential, shaft sinking without freezing was considered dangerous. In the course of time, rock mass freezing technology and experience were evolved and this technology became safer and more reliable. New techniques appeared not only in the technical method of freezing, but also in the matter of designing. Computer aided techniques allow engineers to make a detailed analysis and view of freeze wall development. Nevertheless it is important to determine basic thermal rock properties. In this paper, the evolution of knowledge and engineering experience taken in Polish copper mines and current knowledge level in that matter were shown.

Aug 1, 2013

By A. L. Mular

"On behalf of Bob Bruce and myself I would like to begin by stressing some key points.First, most of us know that the Canadian Mineral Processors was formed in 1969 and is an offshoot of the Canadian Gold Metallurgists. I attended that first meeting in 1969, and I haven't missed a meeting since! Pretty obvious that CMP serves the best booze! At any rate, we know that our meetings are supported by CANMET. Camsell Hall is always at our disposal; Bob Bruce acts as permanent secretary pretty much free of charge; we receive a financial grant from CANMET. This brings me to a second point.Second the Canadian Mineral Processors do not enjoy a free ride in this relationship. CMP provides a genuine service to the mining industry, to government, and to universities. For the industry, CMP serves as a forum for the rapid dissemination of new ideas and new technology developed at remote locations throughout Canada. New developments outside Canada are introduced by invited speakers at our meetings. The effect is to help reduce operating costs and increase efficiency.For government, problem areas and research priorities can be isolated through mutual discussions. Direct communication at our meetings can help CANMET to temper its goals and modify its national priorities.For universities, CMP provides a wealth of operating experience and practical know how. The yearly proceedings are a major current reference source fo1· those of us who teach mineral processing. Admittedly, the proceedings are publ-shed from CMP coffers. However, I note that our fees are up this year, which brings me to a third point.Third, we face some potential problems of a financial and political nature. From a financial view, we may lose our CANMET grant and other financial good will simply because of spending constraints. Our fees are expected to climb each year thereafter.From a political view, we know that the metallurgical society of CIM is anxious to incorporate CMP as a section. The pros and cons of such a merger have been described in a recent mailing. In th2 final analysis, the political and financial problems are interrelated. There are several alternative solutions to both problems, which brings me to a fourth point"

Jan 1, 1979

By Randolph A. Pax

"The internal operation of a tumbling mill is a very hostile environment and precludes the sustainable operation of internal sensors to measure the mechanisms of charge motion and breakage events. Instead indirect methodologies are required to expand the current understanding developed within a framework of perfect mixing of the mill contents. A number of measurement approaches have been successfully used to explore the operation of SAG mills including strain instrumented lifter bolts, mill shell strain measurement and thermal (energy balance) of operating mills.Early acoustics measurement was developed by Hardinge using a 'microphone' located close to the expected toe location. This signal was an indicator of the mill fill. Improvements were implemented with the use of two microphones straddling the toe location to try to increase the sensitivity of the measurement and reduce ambiguities. Further improvements included a filtered signal indicative of steel interactions. Unfortunately, the mechanisms of signal generation and the complexity of the processes do not provide a consistent signal.In recent years, advanced acoustic measurement using arrays of microphones utilising signal processing techniques have been implemented as SmartNoise and validated on over 30 mills. This paper will discuss the results obtained with signals such as water holdup, mill shell steel hits and two each of the toe and shoulder angles. An estimate of the internal mill component wear rates is also accessible.Advanced acoustic measurements with wide bandwidths when combined with physics models and process understanding has achieved a step change in the understanding of the dynamic internal operation of a tumbling mills on time scales of 80 ms. These techniques have been used extensively on SAG mills, but have also been applied to FAG and ball mills. Acoustic measurement is used for the rapid diagnosis of mill conditions and holistic control for optimisation and stability."

Jan 1, 2016

By K. Mayhew, A. Lossin, H. Salomon-de-Friedberg

"The proportion of arsenic-bearing copper concentrates that supply the copper industry is on the increase. The current strategy of miners and smelters to blend feeds to reduce average arsenic levels is rapidly becoming unsustainable as more concentrates with even higher arsenic levels enter the marketplace. In addition, the capability of smelters to manage increasing arsenic levels to more stringent and restrictive environmental standards is limited by available process technologies.CESL Cu-As Technology is a viable technical and economic alternative to traditional smelting. It offers the advantage of simultaneous leaching and precipitation of the arsenic in a single processing step while achieving high copper extractions. The process has been piloted in six separate, fully-integrated pilot campaigns for feeds ranging from ~1% to 12% arsenic in concentration. This paper will focus on the behaviour of arsenic in CESL’s leaching/precipitation step and operational factors that influence it, and on the chemical and physical characteristics of the subsequent iron-arsenic residue that represents today’s best available technology from a long-term sustainable (capital/operating costs, metal recovery, safety, environmental) perspective.The examples provided will demonstrate copper extractions approaching 99% and arsenic deportment to residue of 99%. Instantaneous settling rates of the residue were measured at 15+ m/hr. Data from subsequent short and long-term stability testing of the residue confidently support the view that the scorodite-bearing residues from the process will be stable and provide an acceptable arsenic management practice. The technology offers increased revenue and environmental certainty for miners, smelters & refiners to support the development of metallurgically challenged copper-arsenic deposits. Furthermore, results will be presented demonstrating the technology’s ability to successfully incorporate hazardous arsenic containing smelter by-products such as dust into the process feed and simultaneously extract copper value while fixing the arsenic in a stable residue."

Jan 1, 2016

By W. A. Jones

"The Ross mine, a subsidiary operation of Hollinger Consolidated Gold Mines, Limited, is near the north end of lot 1, con. II, Hislop tp., Ontario. The property comprises the north half of lot 1, con. II, and the south onethird of lot 1, con. III. It is readily reached by a good motor road from the village of Ramore, 7 1/2 miles to the southeast on the Ontario Northland railway. The mine is being developed to a depth of 1,500 feet, and the current daily production rate is approximately 300 tons. From the inception of operations in March 1935 until December 31, 1945, 692,000 tons of ore, with a total value of $5,762,685, was milled . The silver to gold ratio of 1.48 to 1 is unusually high for Ontario gold mines.TYPE OF 0REBODIES AND MINERALIZATIONThe orebodies consist of lens-shaped and pipe-like stringer lodes and tabular vein zones composed of parallel quartz stringers. The host rocks are steeply inclined eruptive breccias and tuffs, striking N.70°W., intruded by very small stocks of red syenite. The orebodies appear to be spatially related to an intricate system of fault planes. Hydrothermal alteration is widespread and is not zonally related to individual quartz stringers. The wall-rocks contain abundant fine-grained pyrite, but gold is confined to the quartz stringers.RELATIONSHIP TO REGIONAL STRUCTURELack of outcrops has prevented the detailed mapping of the Keewatin complex in the vicinity of the Ross mine with the degree of success that has been achieved in the Porcupine area.A northwesterly trending belt of slates and greywackes, bounded by faults, forms the central part of a broad anticlinal arch about 3 1/2 miles north of the Ross shaft. Lava flows forming the south flank of the structure face south toward the mine. If the sediments are to be tentatively correlated with the large areas of Keewatin slates and greywackes of the Porcupine area, it must be assumed that they are younger than the lava flows and that they have been down-faulted."

Jan 1, 1954

By Q. Ricoux, F. Goettmann, A. Maihatchi

"Electrodeposition processes are widely used in the metallurgical industry to produce, extract and refine metals from various feed materials. However, raw materials used to provide non-ferrous metals often contain high amounts of iron. In the presence of iron, while metals are plated at the cathode, electrowinning processes produce corrosive and highly oxidative ferric ions at the anode that are harmful for the process sustainability. In fact, these ferric ions cause dramatic current efficiency loss, induce high maintenance expenditures to limit the corrosion of devices and it results in the formation of impure and dendritic deposits on the cathode. Consequently, the management of iron in electrodeposition process became a major issue in non-ferrous metals production. Actually, numerous methods have been developed to limit the ferric ion concentration in the electrolyte or, at least, to limit its harmful effect. Many methods aim to limit the iron(III) concentration in the electrolyte, generally by coupling electrowinning to extraction process such as solvent extraction (SX) (Bender & Emmerich, 2015), ion exchange (IX) (Gula, Dreisinger, & Horwitz, 1996) or cementation (Kust, 1979) processes to remove ferric ions. Other routes consist of (i) using the ferric ions oxidant properties to leach raw materials, either directly in the electrolytic cell (Fanta & Tributsch, 1975) or through a secondary circuit (Cain, 1950), or (ii) reducing ferric ions through periodic reversal of direct current to enhance the formation of Fe2+ (Loutfy & Bharucha, 1980). On the other side of the spectrum, papers discuss methods to valorize the iron from by-products of the non-ferrous metal industry, that generates vast quantities of iron containing wastes (A. Agrawal, Sahu, & Pandey, 2004). Many studies on iron electroplating and electrolytic iron production from ores have been carried out (Cain, 1950; Mostad, Rolseth, & Thonstad, 2008), but very few have been conducted on waste or by-products. Therefore, we propose to build on the previous literature review to develop a process for the production of electrolytic iron from by-products.INTRODUCTIONNon-ferrous metals and their alloys are used in a large variety of applications. Aluminum and titanium are used for their strength, light weight and corrosion resistant properties in structural applications. Copper has been used in various applications requiring high thermal and electrical conductivity, as kitchen products and electrical wires. Nickel and zinc are commonly used as plating materials; nickel offers a wide range of working temperature and zinc is used for steel plating. Gold, silver, and platinum group metals are used in electrical/electronic applications, jewelry and chemistry as catalysts."

Jan 1, 2016

By Rolf Andreas Lauten, Guy Kluck

"Formation of scales may have important detrimental effects in many mineral processing applications. A well-known problem is the need for frequent maintenance to remove scale from processing equipment. Another challenge may relate to encapsulation of valuable minerals in precipitating scale. In this work, we explore the ability of some crystal growth inhibitors to prevent or lower the degree of scale precipitation. In many situations pregnant leach solutions contains substantial concentrations of calcium, magnesium, sulfate and carbonate in addition to dissolved valuable elements, e.g. gold, copper, zinc. Together with non-dissolved gangue minerals, some slurries may also contain particulate gold, copper etc. During normal processing of the pregnant leach solution it may be exposed to temperature gradients or similar promoting precipitation of various scales. Valuable minerals may become entrapped in precipitates and thus become inaccessible to the lixiviant. Use of a crystal growth inhibitor may lower the degree of encapsulation of valuable elements.Using a simple model system, supersaturated with respect to gypsum, the effect of some crystal growth inhibitors on the prevention of scale is evaluated in terms of amount precipitated gypsum, the particle size of the precipitated gypsum and the carbon gold loading capacity.INTRODUCTIONGold bearing sulfide ores are often roasted or pressure oxidised prior to leaching. The purpose of this unit operation is to prevent loading the leaching circuit with sulfides that consume cyanide. Pressure oxidation or roasting chemically converts the sulfides into sulfates and at the same time, the pH of the slurry ends up in the acidic range. Typically, lime addition is the preferred means to raise the pH to around 10 where gold leaching takes place. Combination of large amounts of calcium ions from the lime with sulfate ions from the ore induces precipitation of gypsum. Compounds like calcium carbonate may also precipitate if carbonate ions are present in the slurry. Depending upon the composition of the ore, compounds like calcium carbonate and other types of scale may also precipitate on gold surfaces on the slurry particles. A layer of scale on top of exposed gold surfaces will prevent dissolution in the cyanidation that takes place during leaching. Naturally, such a precipitation may lower the gold recovery."

Jan 1, 2016

By Zhou Yanwen, Fudong Wang, Shing Liu

Mixed CrB2 and MoS2 powder (Cr:Mo=1:1 atomic %), without any further process, were used as the targets to be sputtered and deposited onto stainless steel and silicon substrates by pulsed DC power supply. The structures and properties of the CrBMoS films were then analyzed by using SEM, XRD, micro-hardness tester. The SEM morphology of the films showed dense, defect free structure, and the preferred orientations of the films were CrB2 (111) and MoS2 (200) according to XRD spectra. The thicknesses of the films were measured and the relationship between the deposition rates and pulsed factors was determined. The films, with the micro-hardness as high as 19GPa and friction coefficient as low as 0.02, could be considered to be the hard solid lubricant films.

Jan 1, 2015

By Elisabeth Kolar, Rik Catthoor, Frederik H. Kriel, Rossen Sedev, Gareth Hatch, Army Research Laboratory, Craig Priest, Scott Middlemas

"This paper reports solvent extraction of rare earth elements (REEs) carried out using a microfluidic device and considers the REE loading limit of the organic phase under laminar flow. The microfluidic device contacts aqueous and organic phase streams for a precisely defined contact time (subsecond resolution) and then separates them for offline analysis. Experiments are reported examining the effect of contact time on extraction. We focus on three REEs: one ‘light’ (Nd), one ‘mid’ (Dy), and one ‘heavy’ (Yb) REE, which are extracted using Cyanex® 572. It appears that loading limits may be locally exceeded in the organic phase near to the liquid-liquid interface, where third phase deposits are observed. Third phase formation was also observed close to the liquid-liquid interface in two-dimensional confinement, showing similar third phase adsorption on glass plates. It is also shown that, under microfluidic flow, a typical first ‘split’ between heavy REEs and light REEs can be carried out without exceeding loading limits.INTRODUCTIONMicrofluidic solvent extraction has emerged as a useful tool for studying extraction of metals in a mineral processing context (Ciceri, Mason, Harvie, Perera, & Stevens, 2013; Ciceri, Perera, & Stevens, 2011; Kriel et al., 2015; Mason, Ciceri, Harvie, Perera, & Stevens, 2013; Priest, Zhou, Klink, Sedev, & Ralston, 2012; Priest et al., 2011). The main advantages are the extremely well-defined and tunable flow behaviour, large surface-to-volume ratios, short contact times, and minimisation of sample and reagent amounts. Two main flow configurations have been studied to date: droplet-based and co-flowing streambased extraction. In the former, droplets are formed at a microchannel junction (usually a T-junction or flow-focusing junction) and flow downstream as plugs or ‘free’ droplets. In our case, stream-based extraction, the chip is a plate (often glass) with embedded microchannels (i.e. with cross-sections of tens of micrometres) that carry the aqueous and organic phases in contact without forming droplets. Thus, these chips play the role of a mixer in a conventional mixer-settler and phase separation takes place by branching the streams or collection in a vessel at the chip outlet. Stream-based extraction requires stable streams that are usually supported by a particular channel geometry (e.g. guide structure or small ‘pillars’) or surface chemistry, and flow parallel bounded by the liquid-liquid interface(Aota, Nonaka, Hibara, & Kitamori, 2006; Hibara et al., 2005; Hibara et al., 2002). Phases are disengaged downstream at a Y-junction, which is a qualitative difference between microfluidic and bulk extractions."

Jan 1, 2016

By H. Dundar

The first application of High Pressure Grinding Rolls was in 1985 at a cement plant, for the purpose of capacity improvement. Then various circuit configurations were derived to achieve a reduction in overall specific energy consumption, by transferring more of the grinding required to the HPGR. In most circuit configurations, the recycle of fines is required for effective breakage between the rollers. By increasing the fines amount in the feed material to a specific level within the recycling load, a uniform material bed is created and a higher pressure gradient along the roller width is obtained, resulting in compact flakes, including more fines. The fines recycle results in enhancement of the interparticle breakage. This paper will discuss the effect of the feed size distribution on HPGR performance.

Jan 1, 2012