Search Documents

By Bordeaux Sciences Agro-INRA UMR 1065 SAVE, S. Piutti, E. Benizri, S. Lopez

Ultramafic soils display high concentrations of nickel (Ni) and a number of nutrient deficiencies (e.g. N, K, P). Ni-hyperaccumulator plants have evolved on such environments, developed specific metal homeostasis showing concentrations of Ni sometimes above 1% in their aerial biomass (Baker & Brooks 1989). Alyssum murale, a Ni-hyperaccumulator, is commonly found around the Mediterranean but can grow on non-ultramafic soils as well, with an altitudinal extension ranging from sea level to 2000 m.a.s.l. Rhizosphere bacterial communities associated with Ni-hyperaccumulator plants can differ from those of non-accumulating plants growing at the same site. Among edaphic factors that could influence the phylogenetic structure of the bacterial communities, altitude and metal-bioavailability and in particular nickel could be significant. However, most studies have focused on analyzing soils with techniques that provide little detail about the phylogenetic structure of these bacterial communities present in ultramafic soils. The objectives of this study were to understand the specific changes in the structure of A. murale rhizosphere bacterial community that occur across two gradients: 1°) elevation and 2°) Ni geochemistry, using pyrosequencing technique (454-pyrosequencing of 16S rRNA gene). It was found that the higher the soil chemically-available Ni contents, the higher the relative abundance of Proteobacteria and Actinobacteria. On the contrary, the abundance of TM7 decreased with increasing levels of available Ni. Moreover, Chloroflexi was present with 53 to 77% of relative abundance. These results demonstrate that soil chemically-available Ni drives the bacterial community diversity in the rhizosphere of Alyssum murale regardless the elevation gradient and other different soil physicochemical parameters. These results should now be confirmed in different ultramafic edaphic environments worldwide (e.g. ultramafic lateritic covers) and in the rhizosphere of different hyperaccumulator taxa.

Jan 1, 2016

By M. Wittke

"In the course of the extension of the railway network in Israel, currently the two 4.6 km long tubes of the Gilon Tunnels on the line from Akko to Carmiel are being constructed. The tunnels run through the limestones of the Bina- and Yirka-formations, which locally are karstified. The maximum overburden amounts to 160 m.The limestones are mostly horizontally bedded and vertically jointed. Occasionally also inclined joints exist. The tunnels cross various fault zones, which mostly strike at an acute angle to the tunnel axis and are steeply inclined. The karstic cavities which were encountered during tunneling have partially been filled by clay. In the vicinity of the fault zones, the rock has often been strongly jointed and weathered respectively. The two single-track tubes have a cross section with vertical walls and an open invert. The tubes are connected by cross cuts with a spacing of approx. 250 m.During the tender phase, WBI has elaborated the tender design for a joint venture of a Chinese and an Israeli construction company. After the joint venture had been awarded the contract, the preliminary and the detailed design have been elaborated by WBI and the construction works have been guided. On the basis of the geological description, rock mechanical models have been elaborated, followed by stability analyses on the basis of the Finite Element method. The tunnels have been excavated according to the shotcrete method. The support in most areas only consisted of a very thin shotcrete lining and radial bolts in the area of the roof. Depending on the degree of jointing and weathering, locally advancing support by means of spiles has been applied.The internal lining of reinforced concrete has been constructed in parallel to the heading of the tubes. Mucking and delivery of materials was carried out through the cross cuts.The breakthrough was achieved in April 2014 and thus within schedule. The predicted distribution of the excavation and support classes along the tunnel has been in good agreement with reality."

Jan 1, 2015

By J. Sugai

Formability of extruded round AZ31 magnesium alloy tubes with different manganese concentrations was evaluated by performing bending tests and measuring strain along the length of the tubes during the bending process. It was found that an increase in the manganese content from 0.3 % to 0.7% did not exert any significant effect on the values of yield stress, elongation, or compression to fracture. However the hardness tended to increase and the UTS decreased. The compressive ductility was significantly lower than tensile ductility for all manganese concentrations. Consequently, the formability of tubes decreased, causing cracks in areas where compression strain occurred during bending. It was also found that a larger strain occurred in the latter half of the region along the length of tube between the clamp-end and the tube-positioning block. Within this region, alloy tubes with higher manganese concentrations, 0.5 and 0.7 %, there was a clear strain peak within the strain profile, while for the 0.3 % Mn alloy, a more uniform strain profile was exhibited, indicating a more uniform deformation. This was confirmed by microstructural analysis of the specimens.

Jan 1, 2006

By Chen Bang, Xia Xiao’ou, Zhang Feng

"Ores with compressive strength lower than 150 MPa are usually easy to be crushed by conventional jaw crushers and cone crushers. However, for hard ores with compressive strength exceeding 150 MPa and 200 MPa and even up to 250 MPa, such as andesite, hard basalt and olivine, it is difficult to reach satisfactory crushing size and yield or difficult to meet service life and stability use requirements of quick-wear parts by using conventional crushers. As continued increase in ore mining depth and constant generation of new type materials, equipment demand for crushing hard ores becomes increasing high. A new type inertia vibrating crusher is designed. It is powered by a high-speed rotating vibration exciter and can obtain required crushing force by adjusting eccentric mass, eccentricity and rotating speed so as to crush various ores with high hardness. This paper introduces the design process of its structure and working principle, discusses the design calculation methods of vibration excitation system, vibration damping and energy storage system and other key mechanism and provides technical references for this type of vibrating crusher.DESIGN PHILOSOPHYThe conventional jaw crusher mainly acquires extrusion force from crank motion to realize crushing. The motor drives the eccentric shaft via the transmission device to bring the moving jaw to swing relative to the stationary jaw. When the moving jaw moves close to the stationary jaw, ores between them are crushed by extrusion; when the moving jaw moves away from the stationary jaw, crushed ores are discharged from the discharge gate at the lower end between the moving jaw and the stationary jaw.The conventional spring cone crusher and the hydraulic cone crusher mainly acquire extrusion force from cranking motion to realize crushing. The motor drives the eccentric sleeve via the transmission device, the moving cone shaft generates an eccentric distance to make cranking motion under the action of the eccentric sleeve. When the moving cone moves close to the stationary cone, ores between them are crushed by extrusion. When the moving cone moves away from the stationary jaw, crushed ores are discharged from the discharge gate at the lower end between the moving cone and the stationary cone under the action of dead weight."

Jan 1, 2016

By Joseph Carlston

With environmental regulations continuing to restrict the discharge of phosphorus from wastewater treatment facilities, traditional methods of phosphorus removal are proving inadequate. To achieve the phosphorus control necessary, a new coagulant used for phosphorus removal, cerium chloride, has been studied in several municipal and industrial wastewater treatment facilities that must meet a phosphorus discharge limit of 0.5 mg/L or lower. These studies demonstrated the high phosphorus removal capabilities of cerium chloride, with the results illustrating the ability for cerium chloride to reduce phosphorus to low concentrations in the effluent using a lower volume of product as compared to traditional coagulants, such as ferric chloride. This reduction is due to the unique ability of cerium chloride to remove phosphorus as cerium phosphate, whereas iron- and aluminum-based coagulants rely on adsorption and co-precipitation.

Jan 1, 2014

Flotation of a mineral bearing particle is the result of successful completion of a chain of events, such as, producing particles with sufficient exposure of the valuable mineral on the surface, reagent adsorption, suspension of the particle in the pulp, collision of particle with air bubbles and subsequent attachment, ascending to the froth column and transport to the concentrate stream, among others. These sub-processes in turn are affected by the feed properties such as size and density, and process variables such as size of air bubbles, degree of turbulence in the cell, particle/particle interactions etc.. Thus, inefficiencies occurring in any one or more of the above processes will result in inefficient flotation performance. In spite of its dependency on a wide variety of sub-processes, flotation performance is commonly modelled based on first order kinetics using two or three parameter models. As the model parameters may be affected by several of the sub-processes mentioned above, interpretation of their variations and identifying the specific causes is extremely difficult. Of the many factors that influence the flotation performance, liberation information of the particles such as the grade distribution and surface exposure are considered vitally important. In this paper, it has been demonstrated a) how a predictive liberation model may be derived and used in quantifying the liberation information of the particles produced at various grind sizes and b) how the flotation process may be modelled by explicitly incorporating the liberation information, thereby improving the accuracy of the model. Comparisons of the observed data with the proposed model and those of published liberation/flotation models have also been made.

Jan 1, 2016

By L. Lafrenière

A trend in mining exploration is to increase the number of geophysical parameters collected and interpreted for geological features in a given area. Airborne technology now allows us to simultaneously combine electromagnetic, gravity, aeromagnetic and radiometric surveys. We report the results of a multiparameter survey conducted in the area of Kamiskotia, Ontario. This area is located near and on the West side of the multi-metalliferous Kidd Creek deposit. Various metallic occurrences are reported in the studied area. Integrating multiple parameters in the interpretation produces a more detailed pseudogeological map than what has already been published. 3D interpretation has been undertaken using some of these parameters and suggests that future work is required in 3D earth model solutions in order to fully use all parameters.

Aug 1, 2013

By Mikael Ramström

The IREDES Special Interest Group (SIG) for Drill rigs has been active since its inception at MineExpo 2000, in Las Vegas USA. The SIG for drill rigs is responsible for the development of a IREDES Drill rig profile. This includes the exchange of production planning, performance and quality reporting data between various kinds of drill rigs and the databases used by the operating mine. During year 2001 a first draft of the drill rigs profile was jointly prepared by drill rig suppliers, mining companies and third party suppliers and reviewed during several SIG meetings. In mid 2002 the profile was released for prototyping projects and since then, feed back received from these projects has been used as input to the first official IREDES release. LKAB and Atlas Copco decided in 2002 to start an IREDES prototyping project using the Simba L6C production drill rig as target equipment. The goal was to verify the drill rig profile and identify possible problems prior to the official release. This was done by implementing the IREDES prototype version in the LKAB?s production planning system and Simba rig control system. The Simba rig control system was designed to handle drill plan and logging information coming from the mine planning system. In parallel to this the mine production system was adapted for drill plan export and logging data import on IREDES format. This paper presents the most recent results of this prototyping project. Result from late 2002 show that the basic architecture of the drill rig profile works and that a common language for data exchange, IREDES will be a central issue for future mine automation. As a result from this and other IREDES prototyping projects the official IREDES release will be available in 2003. Soon after that release IREDES compliant products can be expected. This will include drill rigs and mine production planning systems.

May 1, 2003

By Georgia J. Lysay

Kemess South Mine ended operations in March 2011. Final reclamation works began during operations in 2008 in anticipation of closure. The focus of reclamation during mine operations was on the inactive areas of the tailings dam, waste rock dumps, and expended borrow areas. The general reclamation strategy for the Kemess Mine site marries long-term erosion control with successional reclamation principles. For disturbed areas, this requires application of growth media, proper preparation of surfaces, and introduction of native pioneer plant species to initiate successional processes of recovery. Tailings are retained behind an earthfill dam of approximately 140 m in height, with a crest length in excess of 1 km. Reclamation activities at the dam have included placement of growth media, specialized surface preparation and construction of diversion ditches. The final closure spillway is currently being constructed, with completion scheduled for summer 2011. The two main waste rock dumps contain segregated non-acid generating (NAG) waste rock and potentially acid generating (PAG) waste rock. Resloping of the NAG dump for long-term stability commenced in 2009, followed by placement of growth media and ground preparation. The PAG waste rock will be fully relocated into the expended open pit for final, permanent subaqueous disposal.

May 1, 2011

By R. B. STEWART

A few days ago, while reading a report of the late Dr. Robert Bell in preparation for this afternoon's meeting, I found some impressive figures concerning the magnitude of the Hudson Bay basin. From the waters of the Bay itself, this great territory extends eastward 500 miles, westward l,300 miles to the Rocky mountains, and southward to the source of the Red river. It has a width of 2,100 miles from east to west, and a length of l,500 miles from north to south. Its area is almost three million square miles. It is not, of course, my intention to review the natural resources of this vast territory, but to confine my remarks to that portion of it adjacent to the waters of Hudson bay. A number of erroneous ideas exist in the minds of many concerning this northern country, especially as regards its latitude and climate. Burwell, at the entrance of Hudson strait, is in the latitude of 60 degrees or roughly that of the north of Scotland. The southern end of James bay has about the same latitude as the northern end of Vancouver .island.

Jan 1, 1928

By T. Bednarski, T. McCallum, L. Moya, L. Nsenga, B. Mbao

The accumulation of solids in solvent extraction (SX) circuits can cause problems with the physical and economic performance of the operation. These solids are responsible for the formation of crud, a solid stabilized emulsion containing organic, aqueous, air, and fine solid particles. The build-up of crud in SX settlers can limit SX operation throughput, require plant downtime, lead to higher organic losses, or result in higher aqueous in organic entrainment (all of which can have a significant, negative economic impact). Current practices for crud management are typically reactive. Crud is physically removed after it has been allowed to build to excessive levels in the circuit and processed mechanically using centrifuges or filtration. A new proactive solution has been developed to prevent crud formation and build-up. Low ppm dosage of an additive, ACORGA® CR60, into the pregnant leach solution (PLS) has resulted in reduced crud formation in pilot and commercial scale for a variety of PLS streams. This paper will review results from operations in North America and Africa, covering heap leach, concentrate leach, and agitated leach feeds. INTRODUCTION Crud formation and build-up in solvent extraction (SX) circuits has been a long time topic discussed and claimed to be crucial to the whole hydrometallurgical process (Liu, et al, 2006). Crud formation is present in all SX systems be it copper, uranium, zinc, etc., and Ritcey (1980) defined crud as a stabilized emulsion containing organic, aqueous, and fine solid particles. The ore type and feed composition is a major determining factor of crud formation and typically contains Si, Al, Fe, P, and sulfates (Ritcey, 1980). It typically builds at the interface between the organic and aqueous, but can also be observed as floating crud on the surface of the settler, or bottom crud, which is common to find in circuits treating agitated leach feeds such as in Africa. As crud formation has been unavoidable, many of the current crud management techniques are reactive, allowing crud to form and build in SX circuits. Once it does, it is removed and treated via different mechanical techniques, typically through some type of filtration or three-phase centrifuge, to remove the solids and recover the organic phase trapped within the emulsion (Ritcey, 1980). Automated pumping systems have also been designed and are frequently used in North American operations. The time and capital required to react to crud formation can be an overwhelming aspect to SX operation.

Jan 1, 2019

By K. Stankiewicz

Projects as regards state-of-the-art mechatronic systems aiming at increase of safety in the mining industry and at improvement of coal production technologies, which have been completed at the KOMAG Institute of Mining Technology, are presented. These projects cover automation, monitoring and visualization systems, systems for implementation of artificial intelligence techniques, and database recording systems. iRIS system for electronic marking, identification, and recording of components of powered roof supports, which was implemented in 31 Polish mining enterprises, is presented as an example of the work directly associated with an increase of operational safety. Specialists from KOMAG, ELSTA, Ltd., and Silesian University of Technology in Poland, have developed flexible, configurable, and scalable system for data management, which refers to all fixed assets of mining enterprises, meeting the requirements of users as regards marking and identification of fixed assets. The system for control of roadheaders using intelligent algorithms, based on artificial intelligence techniques is also the example of innovative actions. This system aims at increasing the safety and effectiveness of teamwork due to a possibility of remote, semiautonomous operation. Introduction of artificial intelligence technology enables adaptation of roadheader mining system to the present mining-and-geological conditions. Moreover, work aiming at implementation of state-of-the-art system for control of mine jig?s beneficiation node, integrating machines and equipment in one system, is carried out as regards automation, information integration, and visualization in coal beneficiation process. Work on recovery and conversion of thermal energy, which is a by-product during operation of machines and equipment, especially mine diesel drives, is presented. Systems for energy recuperation are more and more important due to the necessity of continuous increase of power production efficiency.

Aug 1, 2013

By Sepulvedam Jaime E., Levi Guzmán Rivera

"Grinding media consumption rates and their dependence on key operating conditions in semiautogenous grinding mills is analyzed on the basis of a detailed mathematical model recently developed by Moly-Cop´s specialists which describes and takes into account the three primary media consumption mechanisms, namely: abrasion/corrosion, surface spalling and impact ball breakage. The influence of key mill operating conditions – such as ball filling, discharge grate opening, mill speed, lifter profile, and ball quality – on their corresponding grinding media consumption rates is explored via a variety of model simulations, discussing in every case the independent contribution of each of the indicated consumption mechanisms to the estimated total ball consumption rate.INTRODUCTIONA thorough understanding of the independent contribution of each grinding media wear mechanism is extremely important, especially in semi-autogenous grinding (SAG) operations where macrowear (spalling) and ball breakage cannot be ignored or neglected. The high impact conditions imposed in modern SAG milling environments has created serious challenges for grinding media manufacturers since their products must be able to perform with minimal breakage and surface spalling.GRINDING MEDIA WEAR MECHANISMFor SAG milling operations, at least 3 different mechanisms have been identified as the main contributors to the observed overall grinding media consumption, here referred to as: abrasion / corrosion, ball breakage and surface spalling.Wear by Abrasion/CorrosionThe abrasive/corrosive wear mechanism has been discussed in depth in previous publications (Benavente Hector, 2007; Guzman Levi, 2014; Sepulveda and Morrow, 2014). The most widely accepted approach to mathematically characterize the consumption (wear) kinetics of grinding media in rotary tumbling mills is known as the Linear Wear Theory (Prentice, 1943; Norquist, 1950; Sepulveda, 2004) which claims that—at each instant 't' after a grinding body enters the mill load—the rate at which the body loses weight is directly proportional to its surface area exposed."

Jan 1, 2016

By W. G. Wahl

The Slave Province, a segment of Archean continental crust, migrated west and north from the northern flank of the Superior protoshield shortly after the Kenoran orogeny. The probable cause of migration, the path it followed and the cause of its coming to rest can be inferred from the Bouguer gravity data. The migration caused an indentation in the edge of the Superior protoshield which precluded the development of the Hudsonian orogenic front under Hudson Bay. As the nickel and asbestos deposits of the Thompson Nickel Belt and the New Quebec Nickel Belt are restricted to this orogenic front, no such deposits would occur under Hudson Bay.

Jan 1, 1973

By W. F. MacIsaac

"The large low-grade Copper Mountain deposit is located in the northern portion of the Gaspé Cooper Mines property. It is approximately 1 mile north of the Needle Mountain deposit. The orebody outlined to date lies in the top 1,000 feet of the Grande Greve formation. Chalcopyrite occurs in association with pyrite and quartz in small veinlets and numerous fractures. The deposit is immediately adjacent and parallel to a quartz-feldspar dyke and may be associated with a nearby porphyry stock. Stratigraphy, alteration and structure appear to have played an important role in ore deposition."

Jan 1, 1969

By Y. Buro

The Bachelor Lake gold deposit occupies an ESE-trending, SW-dipping, silicified shear zone with hematitic alteration. It transects NE-trending, steeply dipping Archean volcanic formations and the O'Brien granite. Major W-SW and N- NE-trending faults have affected the ore zone and the emplacement of the granite intrusions. Movements along the WSW set may have opened the fractures filled by the mineralization. Gold is generally associated with pyrite. Its source, whether a granitic pluton or a volcanic sequence, is undetermined, but the granite probably provided the concentrating mechanisms through heat and hydrothermal solutions.

Jan 1, 1984

By R. A. Ford

The paper outlines: methods used for the determination of wear metals in motor and transmission oils; contaminents in motor, transmission and crusher lubricating oils; and viscosity determinations. Case histories and costs are presented to illustrate the value of an oil analysis program. Introduction NORANDA MINES LIMITED (BELL COPPER DIVISION) is located on the shores of Babine Lake, approximately 450 miles north of Vancouver, British Columbia. Access to the mine is by road from Topley, B.C., about 40 miles away. When a preventive maintenance analysis program was first considered, it was obvious that if samples were to be sent out for analysis, results would not be available for at least a week, due to the distance from any commercial laboratory. The assay laboratory was asked to investigate the possibility of determining wear metals on site. A limited program was started soon after production commenced, and this has now grown to include all large mobile equipment as well as crushers and grinding mills. The laboratory also now determines viscosity, fuel dilution, dirt and abrasives, glycol and water. All these results are ready within two days. This paper will outline the methods used, data interpretation, several case histories and the benefits from such a program.

Jan 1, 1977

By Jie Deng, Wenliang Xiong, Binyan Chen

"With falling rare earth metal prices, low cost beneficiation of rare earth minerals is essential. The “Flotation-Agglomeration-Magnetic” (FAM) separation process is a newly developed technology by IMUMR to economically recover rare earth elements from different types of deposits. The theory of FAM process is to selectively agglomerate rare earth particles and separate from gangue minerals by bubble flotation process. The flotation product is further upgraded by magnetic separation. The FAM process has been successfully applied in industrial production on the Dalucao rare earth ore, Sichuan, China. The average REO grade of rare earth concentrate is 65% in the latest 12 month production run, with an average recovery of 55%.INTRODUCTIONRare earth elements (REEs) include fifteen lanthanide elements coupled with two chemically similar elements (yttrium and scandium). These elements are split into two sub-groups, La to Sm are classified as light rare earth elements (LREEs) and the remaining elements including yttrium are heavy rare earth elements (HREEs) (Kumari & Panda, 2015). The demand of rare earth elements surged in recent years due to their increasing usage in diverse industrial aspects including high strength magnets, phosphors, clean energy, polishing compounds and catalysts (Goley &Scott, 2014).More than 250 REE-bearing minerals have been discovered, but many minerals are with very low concentrations of REEs, varying from 10-300 ppm (Adam &Ping, 2013). The most common rare earth minerals mined are bastnaesite, monazite, xenotime and ion-adoption REE (Chelgani & Rudolph, 2015; Kanazawa & Kamitani, 2006). Before the 1960s, most rare earth resources were extracted from monazite in the beach placer, with the exploiting of Mountain Pass in the United States and Bayan Obo mine in China, bastnaesite became the chief mineral source of rare earth resources (Klinger, 2015). These minerals are commonly separated with gangue minerals by froth flotation, gravity concentration, magnetic separation, or any combination thereof based on their specific physical characteristics (Zhou & Wang, 2014; Adam & Richard, 2014; Yang & Satur, 2015; Xia & Brian, 2015a,b)."

Jan 1, 2016

By W. Petruk

A study was undertaken to determine whether interrelations between mineral grains affect ore breakage during grinding, and to establish a correlation between ore breakage and mineral liberation. A base metal ore from the Brunswick No. 12 deposit in New Brunswick was ground for different periods of time in a laboratory ball mill, and both the unbroken ore and the ground products were analysed by image analysis. The results show that the mode of breakage is strongly influenced by the behaviour of pyrite. Similar size distributions were obtained for material from the 15 minute grind in a laboratory ball mill, for the grinding circuit discharge from a commercial mill, and for pyrite grains in the unbroken ore. This similarity indicates that a 15 minute grind breaks poorly bonded pyrite grains along grain boundaries, and represents the limit of easy breakage for the ore. Such a grind liberates both large separate grains of ore minerals and poorly bonded mineral grains that occur in interstices among pyrite. On the other hand the 15 minute grind does not separate moderately bonded mineral grains nor release moderately bonded interstitial minerals from pyrite; a 45 minute grind in a laboratory ball mill is required. It is assumed that, for Brunswick No. 12 ore, a 45 minute grind in a laboratory ball mill is equivalent to regrinding in a commercial mill. Grinding beyond 45 minutes in a laboratory ball mill breaks the ore by fracturing pyrite across grain boundaries and by chipping grain edges. Such intense grinding does not markedly increase sphalerite liberation from Brunswick No. 12 ore, because most of the sphalerite that can be released was liberated at the 45 minute grind. In contrast the intense grinding increases galena liberation because a significant proportion of the galena occurs as minute inclusions in pyrite. These findings show that ore breakage and coincident liberation depend upon size distributions, intergrowths, and mode of occurrence of the minerals in an ore.

Jan 1, 1988

By G. D. Bysouth, G. Y. Wong

"The Endako molybdenum deposit is located 160 km west of Prince George, British Columbia. It occurs within the main body of the Francois Lake Intrusions, a composite batholith consisting of early, middle and late intrusive phases. The ore deposit is confined to Endako Quartz Monzonite, a middle phase intrusion, which is bound on the north by Carey Alaskite and on the south by Francois Granite, both late stage intrusions. In the mine aretz, the Endako Quartz Monzonite has been intruded by pre-ore dikes of quartzfeldspar porphyry and porphyritic granite, and by post-ore dikesof basalt.The Endako deposit forms a west-northwest trending body that has a strike length of 3360 m and an apparent width of 370 m. It consists of four structurally distinct zones: Endako East, Endako West, Denak East and Denak West. Principal sulphide minerals of the deposit are pyrite and molybdenite, accompanied by magnetite and minor chalcopyrite. Galena, associated with wulfenite and bismuthinite, occurs in some ores of Endako West and Denak as minute inclusions in molybdenite. The sulphides and associated minerals are hosted by quartz veins which occur principally in vein systems. Hydrothermal alteration accompanying ore mineralization has pervasively kaolinized the quartz monzonite host rock, and has locally produced K-feldspar and quartz-sericite-pyrite envelopes on quartz veins.Primary structural controls of the deposit are southwesterly dipping vein systems which strike 110° in the Endako zones, 110° to 130° in Denak East and 170° in Denak West. Secondary structural controls are northeasterly striking vein systems that dip northwesterly in Endako East and southeasterly in Denak. Domal uplift accompanying the rise of latest stage magma is considered to have caused intense dilatant deformation along older west-northwest trending shear zones, producing an elongated structural host for ore deposition."

Jan 1, 1995