Search Documents

By E. Fiset, T. Hennebel, F. Verbruggen, A. Prévoteau, K. Rabaey

Arsenic (As), bismuth (Bi) and antimony (Sb) are known to affect the quality of copper deposits in copper electrowinning operations. The codeposition of As was previously believed to occur only at current densities far exceeding the range of typical current densities for copper electrowinning. In this study, we investigate the copper electrodeposition on different pretreated stainless steel (SS) substrates from bleed electrolyte in galvanostatic mode at –45 mA/cm². Scanning electron microscopy (SEM) micrographs illustrate that during the initial phases of copper nucleation and growth, the current density was locally increased due to the pretreatments. It was reasoned that the codepostion of As could possibly occur in normal electrowinning conditions, but the risk can be substantially reduced by good SS substrate handling and maintenance practices. INTRODUCTION The presence of As, Bi and Sb is known to have a deleterious effect on the copper cathode quality in copper electrowinnings (Hiskey & Maeda, 2003; Hoffmann, 2004; Xiao, Cao, Shen, & Volinsky, 2012; Xiao, Cao, Mao, Shen, & Ren, 2014; Jafari et al., 2017). They are known to influence both the chemical and physical quality of the copper as they can contaminate the copper (Jafari et al., 2017) and affect the copper deposit structure (Hiskey & Maeda, 2003; Kim, Kim, & Chung, 2009), which contributes to a degraded market value of the copper (Tuddenham, 1984). The incorporation mechanisms of these impurities are believed to occur mainly through slime inclusion (F. Xiao et al, 2012) and electrolyte inclusion (Hiskey & Maeda, 2003). Other studies suggested that codeposition of these impurities is possible by their standard reduction potential being close to the one of copper (Xiao et al, 2014). Hiskey and Maeda (2003) investigated the copper electrodeposition on a copper electrode substrate in Cu electrolytes with a Cu, H2SO4, As, Bi, Sb composition representative for commercial copper tankhouses. The combination of voltammographic techniques and Auger electron spectroscopy showed that As was the first impurity to be electrodeposited from this electrolyte, yet at potentials where the limiting current density of the copper electrodeposition reaction is exceeded. The copper tankhouses usually operate at a current density ratio of 0.3 to the limiting current density in order to achieve tolerable copper quality deposits. The codeposition of As could be considered impossible in this current density condition. However, it is known that during the initial phases of electrodeposition on foreign substrates, a substantial part of the reaction proceeds by growth of individual nuclei where the current density is locally high and diffusion limited (Radisic, Ross, & Searson, 2006). Furthermore, it was observed that copper nucleation on TiO substrates occurred preferentially in the scratched oxide free areas which could serve as parts with high localized current densities (Chang, Choe, & Lee, 2005).

Jan 1, 2019

By Hao Zhang

Site inspection is an important component of safety management system. In current practices, the inspectors evaluate the safety condition on a construction site with the assistance of a standardised checklist. However, the checklist emphasizes on evaluating the implementation of safety management system, but provides limited task-specific check items for assessing whether the individual construction tasks are conducted under safe condition and in a safe manner. To address this issue, the research presented in this paper aims to provide safety practitioners with comprehensive and taskspecific safety information to promote effective risk identification and facilitate strategic risk control during site inspection. Specifically, this research first builds a project-specific safety information database, which stores potential risks and control measures for each construction task. The research team then develops a mobile decision support tool to retrieve information from the database and support safer decision-making on site. The tool supports users in two ways: one is to provide daily risk checklists and risk control strategies to guide step-by-step inspection alongside the project schedule; the other is to let users input any safety-related keywords during the safety inspection process and the tool returns relevant safety information by applying text mining algorithms. It is ongoing research. This paper presents an overall research framework and discusses the progress in developing safety database and data retrieval concepts. The outcome of the project will help enhance safety management practices and reduce possible risky working conditions on a construction site.

Aug 1, 2013

By Dharmendr Kumar, Pradip, Beena Rai, Venugopal Tammishetti

"Due to rapid depletion of high grade Indian iron ores, there is a need to utilize low grade fines and slimes. However, these fines and slimes, in their current form, cannot be utilized in steel making due to their high alumina (6-10%) contents. Several beneficiation strategies such as gravity separation, magnetic separation, flotation and selective flocculation are currently being explored for the upgradation of low grade fines and slimes. In our previous work density functional theory simulations were employed to come up with selective flocculants for beneficiation of iron ore slimes. Our simulation results suggested that starch and guar gum are more selective towards iron minerals than other minerals present in the sample. Grinding of iron ore fines becomes necessary in some cases to achieve adequate liberation for removing alumina impurities in Indian iron ores. We have thus investigated effect of grinding of iron ore fines on its selective flocculation-separation.In the present work, we have taken natural iron ore fines from one of the Indian iron ore mines and ground it to -400 mesh (<37 microns) in dry and wet conditions. X-ray diffraction study confirmed the presence of minerals hematite, goethite, gibbsite and kaolinite in the sample. The fine ground samples were used in selective dispersion-flocculation study with corn starch and guar gum flocculants. It is interesting to note that even though the dry and wet ground samples possess almost similar particle size distributions, significant differences were observed in yield and grades of the concentrates thus produced. These differences may be arising due to the coating of alumina containing minerals on iron minerals. We have also studied the effect of addition of dispersant while grinding. Our study suggests that grinding conditions determine the efficiency of the separation process."

Jan 1, 2016

By C. E. Cairnes

The Slocan mining camp in Kootenay district; British Columbia; has long been noted for the great number of its silver-bearing deposits; and for the success that has; in many instances; attended their development. The orebearing area lies east of Slocan lake and mainly within a radius of 6 to 8 miles of the mining town of Sandon. Within this limited area 135 or more properties have shipped ore in quantities of from 100 tons or less to more than 500; 000 tons; and with a total value in silver; lead; and zinc ranging from a few hundred dollars to well over $10; 000; 000. Of the three metals; silver has easily ranked first in value; with lead second and zinc third. Zinc production; however; made slow progress in the early years; and with . the exception of the Lucky Jim mine; and a few others where high-grade ore could be readily hand-sorted; was a detriment to the silver-lead ores until improved methods of separation enabled it to take an important place in the mineral production of the Slocan.

Jan 1, 1954

By A. T. GRIFFIS, R. J. GRIFFIS

A large magnesite-talc body is locared in Delora Township, 11 km sourh-southeasr of Timmins, Onrario. The deposit occurs in part of an Archean greensrone belt dominated by volcanic and sedimenrary rocks and large bodies of ultramafic intrusions. The magnesite-talc zane is abour 1800 m long, has a maximum width of 300 m and has been drilled ro 120 m below surface. Chemical analyses of rhe main carbonate zane average 20 ro 28% soluble MgO (magnesia), 5 ro 6% rota/ iron oxide and less rhan 0.1 % CaO (lime). Mineralogically, the zane consists of approximately 54% magnesite, 28% rate, /5% quartz and 3% hematire. Perrographic srudies suggest that rhe various assemblages of magnesite, rate, quartz and serpentine were derived from a parenr serpenrinire (after dunire). An early carbonitization stage, which produced a high-magnesite, low-talc assemblage, preceded a farer decarbonitizarion stage, which formed rhe main magnesite-talc assemblage. Despite a favourably low calcium oxide content of rhe magnesite-talc rock, considerable iron in the magnesire /at rice has limited the quality of the beneficiared product: rhe besr flotation concentrate to dare yields 92 to 94% dead-burned MgO. Experimen- I L t r i i c:~:.•-4- -------- ? -_;> ,•----1---- ta/ work continues on finding a process whereby high-purity magnesia can be produced on a commercial scale.

Jan 1, 1984

By H. M. Woodrooffe

This paper deals with the laboratory facilities at the Mines Branch for carrying out research in the industrial minerals field, and also reviews current programs in ceramics and construction materials, in non-metallic minerals and in the milling of industrial minerals. It then discusses the application of these pro-grams to industrial problems.

Jan 1, 1967

By Kevin C. Milne

"The solution of problems associated with development of a sour gas reserve will be of increasing importance in tl1e next few years if gas export is approved •by the National Energy Board. The purpose of this paper is to review briefly the history of the Carstairs gas field, and tCI describe in a general manner the reservoir, and the producing and processing facilities.HISTORYThe Carstairs gas field was discovered in April 1958 when the discovery well, Home Carstairs 10-17, was successfully completed as a gas well in the Elkton member of the Turner Valley formation. Geo-graphic location of the field is shown in Figure No. 1. Note that the field is about five miles west of the town of Carstairs, Alberta, which in turn is about 40 miles north of Calgary. Drilling subsequent to the discovery well resulted in three addition-al producing wells and one dry hole during I.958; two producing wells during 1959; and one producing well and one dry hole during 1960. Thus, seven producing wells and two dry holes have been drilled in the Carstairs field to date.In November 1959 a 12-section block in the Carstairs field was unitized on a surface acre basis. Mean-while, in June 1959, operators in the field executed an ""Interim Plant Agreement"" that provided the money needed to start construction of a joint venture processing plant and gathering system. Construction of the plant and gathering system was completed in February 1960."

Jan 1, 1960

By Terry Gerritsen, Sylvain Picard, Bruce MacKay

Virtually all new technologies require a control system. Any intense process has many process variables that react quickly making manual control difficult. Control system design has a significant impact on the success of a plant especially during ramp-up. New technology projects are particularly sensitive to control system design as the process response is unknown. This paper discusses the important factors encountered in the design of a control system for a new technology. Examples are given of successful new technology plant start-ups where tight coordination of the process control system implementation, process design and selection major equipment led to rapid ramp-ups.

Jan 1, 2011

By J. W. Cox, W S. Jones, A E. Chase

For a long time the Oil Industry has been looking for a logging tool which can determine the quality of the cement job behind casing. Older methods such as Temperature Surveys and Radioactivity Surveys might detect the presence of cement behind the casing, but short of production tests, it was impossible to tell that the producing zones were adequately sealed off from adjacent zones. A new logging method, which is called the •Cement Bond Log, operates on the principle that a sonic pulse transmitted by the casing is greatly attenuated when the casing is strongly bonded to an outer annulus such as cement. The down-hole tool consists of a source of sonic energy which is detected by a receiver situated a few feet away from the source. The amplitude of the detected energy is measured and the resulting signal transmitted to the surface where it is recorded versus depth. Amplitude is a function of attenuation and thus the log is readily interpreted.

Jan 1, 1961

By Ryan W. Siggelkow

Mines today use various methods of mining to extract ore. Because of the dangerous nature of many of these processes, remotely controlled LHD machines are being used to extract the ore from the draw point. The remote control system, although being made safer all the time, has remained virtually unchanged for many years. The basic functionality is an operator switching the machine to remote control, getting out of the cab, walking up a stand, operating remotely, returning to the cab, switching to manual, driving manually, switching to remote, and switching to manual. It seems repetitive, and time consuming, does it not? Networking, convergence, video, voice, and data infrastructures, and other technologies are growing by leaps and bounds in virtually every industry and region, except for mining. From the comfort of the living room couch, a Canadian can play hockey online with full voice conversations over the Internet with someone in Russia in real time. Yet, a mine superintendent must jump through hoops to have a private conversation with the front line supervisor underground. "Is Joe around anywhere?" If Joe hears the message, he will respond. If not, who knows? Maybe he&apos;s hurt. Maybe he&apos;s not. Where is Joe? Nobody really knows, and that is scary. Today, surface knows that the workers disappeared into the cage at 7:00 a.m. They also know that the workers will probably and hopefully return at 3:00 p.m. Is there not a better way to handle this? With such a complex industry, it seems as if, for the most part, the introduction of new technology into mining has either been overlooked or has been met with some resistance. It is time to step back, look at the process, and see how it can be improved. Key areas of focus will be safety, productivity, dependability, and cost-effectiveness.

May 1, 2010

By T. Purushotham, B. Samanta

ABSTRACT; The shaft bottom junction in a mine ventilation system is an important source of shock loss due to the combined effect of bend and area change. The occurrence of high-volume ?ow rates through this con?guration can potentially result in high energy losses. The current research examines the process of shock loss at a characteristic shaft bottom junction of an underground coal mine. Investigations are per-formed on both laboratory-scale models and three-dimensional computational ?uid dynamics (CFD) simulations, under both exhausting and forcing shaft bottom conditions. The effects of the plat roughness and the shaft bottom length on the shock loss factor values are also examined. The studies show that the combined effect of bend and area changes that occur at the shaft bottom junction results in shock loss factors that are much higher than those values resulting from abrupt area change only. The transition from a smooth wall condition to an unlined rough airway condition (relative roughness, e/d = 0.112) can increase the shock loss factors by 40%. The effect of shaft bottom length on the shock loss factor has not been clearly established due to con?icting results produced by scale model studies and the CFD simulations.

Jan 1, 2010

Presentation Outline ERM ? corporate profile Background to sustainability reporting GRI G3 Guidelines (Oct 2006) Best practice examples Contact information ERM ? corporate profile Over 35 years of experience World?s largest all-environmental consultancy* 130+ offices in 40+ countries; 3,200+ professional staff Worked with >50% of the Global Fortune 500 (FY07) Annual turnover > US$500 M (FY07) 2008 Environmental Advisor of Year** Offices/Staff ? Canada (5/50) and US (65/1,350) *Source: Engineering News Record: July 2, 2007 ** Source: Acquisitions Monthly: December 2007

May 1, 2008

By G. Reuben Yourt

This paper consists of two main parts. The first, under the heading Preparations, deals with suggested preparations to be carried out in advance so that loss of life might be prevented should a fire occur. The second part, under the heading Fire Procedure, deals with actual organized procedure to be followed for the preservation of life if and when a fire occurs. The writer realizes that these preparations and procedures may be to some extent applicable to only a few mines with a relatively simple vein system and that each mine would need to formulate a procedure to conform to its own particular conditions, scope, and degree of complexity. Preparations 1. - Ventilation Control The objective in ventilation control in the event of a tire underground is to keep the travelways, through which men must pass to reach surface, supplied with air not deficient in oxygen and free from gases and smoke. Without some control of the volume and direction of the main air currents flowing through the mine, the success of removing men to surface might be seriously hampered. ? This control is achieved by means of mechanical ventilation forcing air through desired airways and workings with the assistance of doors to regulate the volume and direction of the air flow. In connection with fans and doors, the possibility of short-circuiting should always be taken into consideration, as it can often nullify the value of a fan and possibly trap men in dangerous atmosphere if the short-circuiting involves the fire area. Main fans are often installed so that they can be reversed in a short time. However, fans should not be reversed unless this is found absolutely essential by those in authority. Misjudgment in this respect could cause the loss of life to men who might naturally take refuge in what they believe by experience to be a fresh air stream. Another precaution to be taken is to see that doors in airways are fastened in a fixed position so that they cannot be sucked or blown open when the fan is reversed, otherwise short-circuiting could possibly render the fan useless.

Jan 1, 1947

By M. P. Davies

"Risk, the product of probability and consequence, is an integral part of mining. Whether evaluating exploration priorities, determining property acquisition potential, reviewing the components of an operating mine or assessing environmental/closure issues, the concept of minimizing risk is central to economic and technically appropriate decision making.Until recently, risk evaluations have tended toward a strongly mathematical basis. With this previous trend, it was essential to establish precise probability density functions to all assessed components or issues where often little information was available. The combined effect of the seemingly complex analyses with corresponding insufficient data often resulted in either a poorly executed risk evaluation or no evaluation whatsoever; either result not acceptable for optimal decision making. This paper presents a simple and practical procedure to carry out risk assessments for the mining industry. Although simplistic in nature, the power and usefulness of the technique is immense. The basis for the procedure involves combining deterministic assessments (often “gut feel”) with appropriate probabilistic descriptors. The resulting procedure, termed Potential Problem Analyses, or PPA, can be used anywhere an evaluation of risk will assist in optimizing technical and/or economic decisions. As will be shown, a key element of the PPA procedure is the multi-disciplinary input the framework allows which makes the method ideal for a teamwork approach to decision making."

Jan 1, 1997

By W. G. Hatch

Introduction Classified equipment originally installed in 1923 in the Britannia mill consisted of eighteen Model C Dorr Simplex classifiers, each in closed circuit with a pebble-mill. These machines were only three feet wide and of light construction, so that their raking capacities were necessarily limited, the maximum being about 20 tons per hour for each classifier. On conversion from pebble-mills to ball-mills, in 1924, attempts to increase circulating loads with higher rake speeds resulted only in overflowing a coarser product to the flotation cells. The elevator type of classifier was developed locally in 1935 and during that year two units, each having a sand carrying capacity of from 30 to 40 tons per hour, were installed. With such loads, a material increase in the grinding capacities of the ball-mills was noticed, and, after further development work on the elevator classifier, fifteen of the small Dorr classifiers were replaced by units of this type, capable of handling approximately 75 tons of sand per hour, with later alterations increasing this capacity to well over 100 tons per hour. In the meantime, the three remaining ball-mills had been placed in circuit with Dorr FX classifiers, one of which was six feet wide and the others five feet wide. Impartial and exhaustive tests conducted on the Dorr FX versus the elevator classifier showed the average results on these machines at Britannia to be substantially the same. A large amount of testing was carried on to determine the effect of circulating load on the output of the grinding units. This work indicated a rapid increase in the grinding rate as the ball-mill feed increased up to about 60 tons per hour, after which a relatively slow increase took place up to 100 tons per hour. No benefits were derived from higher circulating loads. A 300 to 500 per cent circulating load, depending on the nature of the ore treated, is considered to be within the economical range for the grinding of Britannia ores.

Jan 1, 1946

By Darryel Boucher, Thomas W. Leadbeater, Raymond Langlois, Joshua Sovechles, McGill University, Zhoutong Deng

"Spiral concentrators are used to upgrade ore based on the density difference between their component minerals. This simple flowing film gravity separator is of interest for the processing of large amounts of material, as found in the iron ore industry. Addition of wash water at different points on the trough of the spiral affects the grade and recovery of the valuable concentrate by affecting the flow of particles within the thin slurry film. This paper shows how radiolabelled hematite (-355+300 µm) and quartz (–1,180+1,000 µm) tracers were used to determine the particles’ behaviour within the slurry film with and without the addition of wash water. The results presented provide a detailed particle flow pattern around a wash water addition point and its effect on the trajectory and velocity of the particles. This information is of interest in building knowledge about spiral wash water injection parameters such as injection location, direction, flow rate and nozzle orifice type (affecting jet shape and velocity).INTRODUCTIONSpiral concentrators are density based separation devices. They are extensively used in the upgrading of iron ore, fine coal and minerals sands (sources of ilmenite, rutile, zircon and monazite) (Wills & Finch, 2016). A spiral unit is composed of a channel of specific profile formed as a helix of 3 to 7 turns around a central structural post. The feed pulp is composed of 15 to 45% solids with particle size from 75 µm to 3000 µm (Wills & Finch, 2016). Throughput of a single spiraling trough can be up to 8 ton per hour and multiple trough unit (up to four trough) can process up to 30 ton per hour for a footprint of around 0.7 m2 (Palmers & Vadeikis, 2010). They are low cost concentrators considering manufacturing of their trough via polymer reverse molding. The energy intensity of a spiral plan is notably small considering the throughput and is mostly related to pulp pumping and final concentrate dewatering."

Jan 1, 2016

By N. Katsikaros, A. Lewis-Gray, P. Richards

"To optimize gold recovery in complex leach-to-electrowinning processes, Gekko Systems developed the Gekko resin exchange column (G-REX) as an intermediate step, using a highly gold-selective resin to isolate contaminant metals. The AuRIX®100 resin produced by Purolite is licensed exclusively to Gekko, with the G-REX column designed specifically for this resin. Operational experience has been gained at the Castlemaine Goldfields Ballarat gold mine. In near-continuous operation since 2008, the Ballarat plant treats unclarified concentrate leach solution. The extension of this technology to higher throughputs and more complex chemistry is discussed.RÉSUMÉ Afin d’optimiser la récupération de l’or dans des procédés complexes impliquant la lixiviation suivie de l’extraction électrolytique, Gekko Systems a développé la colonne Gekko de résines échangeuses d’ions (G-REX) comme étape intermédiaire, à l’aide d’une résine hautement sélective pour la récupération de l’or qui permet d’isoler les métaux contaminants. Gekko détient la licence exclusive pour la résine AuRIX®100 produite par Purolite, et la colonne G-REX a été spécifiquement conçue pour cette résine. C’est à la mine d’or Ballarat de Castlemaine Goldfields que l’expérience opérationnelle a été acquise. L’usine de Ballarat, en exploitation quasi-continue depuis 2008, traite une solution concentrée non clarifiée de lixiviation. L’extension de cette technologie à des capacités supérieures et à une chimie plus complexe est examinée."

Jan 1, 2017

By F. Habashi

Lead is an ancient metal. The alchemists related it to the planet Saturn. It was largely obtained by smelting galena which generally contains small quantities of silver. That is why the metallurgy of lead was closely related to that of silver and in some cases the ore was treated only for its silver content. It was also known during the Roman time that lead vapors were toxic. Lead has been produced exclusively by pryrometallurgical methods. Lead refining is a complex process because of the presence of deleterious impurities such as arsenic, antimony, and bismuth. In the nineteenth century lead played an important role as a material of construction in the manufacture of sulfuric acid. In the twentieth century tetraethyl lead was used exclusively as an anti-knock reagent. In recent years lead is mainly used for making batteries.

Jan 1, 2008

By D. A. Beattie

Talc is a commonly encountered gangue mineral in metal sulfide flotation. Talc is naturally hydrophobic, resulting in high recoveries if polymeric depressants are not used to specifically reject this MgO containing mineral. We have studied the adsorption of a selection of polymers onto talc using a variety of techniques. Adsorption isotherms have been determined using ex situ depletion techniques and in situ ATR-FTIR spectroscopy has been used to determine adsorption kinetics. Adsorbed layer thicknesses have been determined for the polymers on cleaved talc surfaces using the AFM. The effect of the adsorbed polymer layer on the properties of the talc surface has been quantified through contact angle measurements and single mineral flotation tests. Distinct correlations are observed between the adsorbed layer properties and the flotation performance of the polymers. These observations are discussed with reference to the bubble-particle attachment process and the molecular structure of the polymers.

Jan 1, 2006

By B. Wasmund, M. Parravani, M. Jastrzebski, Z. Coull

"One of the main drivers of overall profitability of pyrometallurgical vessels is refractory lining campaign life. Increased economic pressure to improve vessel life requires innovative solutions to the problem of refractory cooling. Hatch has recently developed a high-intensity, waterless cooling system that bridges the performance gap between external shell cooling and internal water-cooled copper elements. External shell cooling has a limited effectiveness in protecting the refractory lining, because it is thermally insulated from the hotface of the lining by its thickness. This situation does not improve until the lining itself has become worn near the end of the campaign. The patented technology developed by Hatch overcomes this problem by positioning high-velocity air-cooling channels within the lining, closer to the hotface where the cooling benefits can be realized throughout the entire duration of the campaign. The current paper presents the development and application of Internal Air Cooling technology as well as results from the pilot campaign in an operating commercial vessel. Various adaptations for this novel, cost-effective and inherently safe system are also discussed."

Jan 1, 2015