Search Documents

By S. F. Guo, B. W. Zheng, X. L. Huang, S. W. Qi

"The study of mechanical characteristics of rock discontinuities under different shear deformation velocities is an important premise of rock slope dynamic response analysis. According to disposing and calculating the experimental results of previous research about peak shear strength of rock discontinuities under different shear deformation velocity of constant normal loading, the law of influence of shear velocity on the total friction angle is studied. Based on the research results, it can be found that the total friction angle of rock joint specimens varies in the form of negative logarithm with the variation of shear deformation velocity. It’s also indicated that the total friction angle of rock joints decreases with the increase of shear deformation velocity for rock joints of relative strong homogeneity and isotropy. However, the total friction angle of rock joints increases with the increase of shear deformation velocity for rock joints of relative strong heterogeneity and anisotropy and the latter amplitude of increase is less than the former amplitude of decrease. The physical property and microscopic geometry of rock joints play an important effect on the increase or decrease tendency and amplitude variation of total friction angle with the increase of shear deformation velocity.INTRODUCTIONThe rock slope dynamic response is largely restricted by rock discontinuities. Hence the study of dynamic characteristics of rock discontinuities, especially the dynamic shear characteristics is an important premise of rock slope dynamic response analysis (Qi et al., 2007). Seismic load is both dynamic load and cyclic load (Liu et al., 2011). Under the dynamic and cyclic shearing actions of seismic load, the rock slope which is stable under the condition of static load may slide along the rock discontinuities whose shear strength reduce and then the earthquake landslides occur. The strength degradation and deformation mechanism of rock discontinuities under the dynamic and cyclic shearing actions is one of the key problems to be solved in the work of earthquake prevention and control of engineering slope. Based on the above understanding, predecessors conduct some researches which focus on the shear behavior mechanical characteristics of rock joints under cyclic shearing actions (Plesha, 1987; Hutson & Dowding, 1990; Jing et al., 1992, 1993; Huang et al., 1993; Qiu et al., 1993; Homand et al., 2001; Lee et al., 2001; Jafari et al., 2003; Liu et al., 2011, 2013). However, there are a few researches about the mechanical characteristics of rock joints under different shear deformation velocities because of the restriction of shear apparatus. Crawford and Curran (1981) conducted a series of one-way cyclic direct shear tests on four kinds of natural rock joints under different shear deformation velocities varying from 0 to 200 mm/s. The tests showed that at low normal stresses the peak shear strength of soft rock joints exhibited an increase up to a certain velocity, after which it remained essentially constant. For rock joints of intermediate hardness, the peak shear strength was essentially independent of shear deformation velocity; whereas for hard rock joints, the peak shear strength of which showed a significant variation with the shear deformation velocity. Jafari et al. (2003) carried out a series of conventional triaxial tests on artificial rock joints of regular saw-tooth shape with axial loading rate from 0.05 mm/s to 0.4 mm/s."

Jan 1, 2015

By E. W. Coderre, R. C. Baxter

"This paper describes the townsite of Wabush and the two railways operated by Wabush Mines for the loading and unloading of iron ore concentrate. The town of Wabush is located approximately 200 air miles north of Sept-Iles, Quebec and is in the Province of Newfoundland and Labrador. Construction of the town-site began in 1961 to provide housing accommodation for the construction force and permanent employees in the mining and milling operations located 4 miles away. Wabush Mines operates two short railway lines in loading and unloading concentrate between the concentrator, located at Wabush, and the pellet plant at Pointe Noire, Quebec. Both of these railways connect with the main line of the Quebec North Shore and Labrador Railway and provide a shuttle service between the two phases of the operation."

Jan 1, 1969

By Jamal Asfahani

Abstract - Natural gamma ray well logging, an effective tool in geophysical prospecting, is used to investigate the radioactive and phosphatic layers in the Khneifiss mine in Syria. The interpretation of the gamma ray measurements, using numerical methods of analysis developed previously and applied successfully in some phosphatic areas in Syria, make it possible to define precisely the phosphate thickness from place to place in the study area. This technique has been successfully applied while studying seven boreholes in the area. Sixty-three core samples from phosphatic layers in the boreholes have been analyzed, using gamma ray spectrometry for the determination of P2O5 , U, Th, and K. Good correlation between P2O5 content and U concentration has been found. The total count gamma logs correlate reasonably well with the U core analysis, suggesting that radioactive equilibrium exists in the U decay series. These gamma logs can be therefore used effectively to quantitatively map the distribution of P2O5 and U. The characteristics of both subsurface phosphatic sand and phosphatic rocks have been investigated and outlined using a statistical approach. The affinity of uranium to some trace elements such as V, Sr, Cu, and Ni has been verified using correlation matrices of these elements.

Jan 1, 2002

By China University of Mining and Technology, P. Zhang, C. Zhou, C. Duan

"Recovering pyrite from the gangue with high sulfur content is of great significance for both economic development and environment protection in China. Due to the global water shortage and high cost in wet separation processes, it is urgent to explore more efficient energy and water conservation method in mineral processing field. This study has proposed an innovative method based on density difference for fine pyrite enrichment by vibration fluidized bed. In this study, the total sulfur content (TSC) of the gangue sample is 19.18%, and the pyrite is disseminated with fine granularity in the gangue which should be crushed for dissociation. The combination and dissociation experiment of -6mm gangue shows that the dominant density of -6+3mm, -3+1mm and -1+0.5mm comminuted material is +2.9g/cm3. Based on the analysis of characteristic, the effects of various factors on the separation performance were experimental studied. The results show that gas velocity, vibration intensity and bed height all have the significant effects. With the increases of superficial gas velocity, vibration intensity and bed height, the separation performance all presents a decreasing tendency. Additionally, the TSC of -6+3mm, -3+1mm and -1+0.5mm materials are respectively up to 37.94% , 35.43% and 30.61% at the optimum conditions, which are the 1.72?1.90 and 2.29 times as much as the TSC of raw material, respectively. This study demonstrates the vibrated fluidized bed can recovery pyrite from the gangue effectively.INTRODUCTIONWith the increasing mining and separation of coal, the yield of gangue has a further growth tendency, which has become one of the largest reserves of industrial waste (Querol et al., 2008). However, many harmful elements, such as S?NOx and Hg, is existed in the gangue leading the serious damage to the soil and environment (Hao, Yun, Zhanyuan, Sen, & Song, 2013). In addition, the economic would be suffered from the loss resulting in the occupied of arable land caused by the accumulation of gangue (Yeheyis, Shang, & Yanful, 2009; Zhou, Liu, Yan, Fang, & Wang, 2012). Therefore, the government has put forward the policies of ""green mining"" in China (Xing & Gao, 2009; R. Zhang, Ai, Zhou, Ju, & Zhang, 2015; Zheng, Du, Li, Qiu, & Yang, 2015). Among different research areas of coal utilization, extracting the useful minerals has become one of hot topics (Ledin & Pedersen, 1996; P. Patra & Natarajan, 2003; Partha Patra & Natarajan, 2004). At present, many researchers has devoted to the desulfurization of coal all over the world. As result, the sulfur element, which is mainly existed in the presence of pyrite, would transferred in the tailings, namely the gangue. Meanwhile, the pyrite is important raw materials to produce rubber, paper, textile and match. Consequently, recovering the pyrite from the gangue is not only suitable to the requirement of ""green mining"", but it could turn the waste into the treasure having the important significance."

Jan 1, 2016

By K. Kawagishi, J. Ang, A. Sato, H. Harada

"We have recently proposed a new ""EQ Coating"" bond coat system to solve the problem of secondary reaction zone (SRZ) formation caused by bond coats applied on the hot section components of modem jet engines. A viable EQ coating alloy was previously found for a representative znd generation superalloy, TMS-82+. It would be ideal if the same could be done for a representative 5th generation superalloy, TMS-173. In this paper, we will show that the coating with the best oxidation resistance in the EQ system of TMS-173, although possessing considerably better resistance than TMS-173, did not have sufficient oxidation resistance. In order to improve the oxidation resistance of the EQ coating for TMS-173, we have ventured into ""Pseudo-EQ coatings"". A diffusion couple between the Pseudo-EQ coating and TMS-173, after 300hrs at 1100°C, had a 0-15µm IDZ, but no SRZ. A diffusion couple between a conventional coating and TMS-173 formed a 80-150 µm SRZ. After a 1 hr oxidation test at 1100°C, the PseudoEQ coating formed a thinner oxide layer than the EQ coating, but still contained NiO and spinel. Aerospace"

Jan 1, 2006

By A. V. Corlett

MR. C. S. Gibson: Mr. Chairman, I listened with much interest to Mr. Corlett's paper. Those of us who are directly engaged in mine ventilation and dust control are impressed by the improved atmospheric conditions to be derived from the use of methods of mining such as those in operation at Aldermac, which Mr. Corlett has just described, and those employed at Noranda. It is a well known fact that drilling-dust is one of the most potent factors in the production of silicosis in mines handling ores containing quartz, so that from that angle the use of diamond drills, instead of percussion drills, to drill ore for blasts in stopes is an important development. A second point which I think merits mention is blasting. Blasting, we all know, creates the most dust in a mine and the fact that you can drill ore for a large blast with diamond drills and fire it, say, on Saturday night, and then have all the next day to ventilate the workings, is a great advance in dust control. 1 have wondered if Mr. Corlett, or possibly those at Noranda, can en-vision the use of the diamond drill as a means of advancing cross-cuts and drifts, preparing stopes, etc. I believe it is a matter which is receiving considerable attention at the moment in some parts of the world and J thought it would be interesting to have Mr. Corlett's reaction on that point. MR. A. V. CORLETT: I am not quite so hopeful of using diamond drills as a means of drilling holes in the ordinary drift. Maybe some of the diamond drill men can give us some further information on that point. MR. R. D. LoNGYEAR: The diamond drill manufacturers are working on that problem, but until further work is done we have nothing definite to offer. Drilling holes with a diamond drill to compete with rock drills for advancing drifts and cross-cuts is a desirable objective, because of the elimination of drilling dust and the ability to cut a smooth bore of uniform diameter. To reach this objective, higher rates of penetration are required, which can only be achieved by discovering the optimum bit rotating speed, by reducing vibration, and by further improving the bits and machines. We are optimistic, but the problem is still largely in the research stage.

Jan 1, 1940

By S. Caron, M. Bourassa, J. Châteauneuf, L. Tardif

"Since many years, the Yvan-Vézina gold plant custom mills and processes different ore types that show different behaviors. Because of this, cyanidation control is more complex than for a typical milling operation. In 1992, a Cyancor™ on-line « free cyanide » analyzer has been installed for monitoring and optimizing cyanidation. This implementation significantly reduced cyanide consumption for the overall cyanidation process. In order to further reduce cyanide costs, an automatic control strategy has been implemented to decrease fluctuations of« free cyanide » from their set points.This paper outlines the major steps of the project: process control audit, control strategy development, implementation and running-in period. Control strategy features include data filtering modules, adaptive PID algorithm and set points management modules are also presented. Finally, the strategy efficiency is illustrated with load-disturbance responses.IntroductionLocated in northwestern Quebec, the Yvan-Vézina plant has an average capacity of 1300 t/d using carbon-in-pulp technology. In 1991, the Yvan-Vézina gold plant was processing three types of ores (Beauchemin, Mouska and Silidor mines) and a pyrite concentrate (Beliveau mine). A cyanide reduction program was then undertaken to reduce « free cyanide» fluctuations <6>. To reach this objective, the optimum cyanide concentration was determined for each ore, a continuous monitoring method with the Cyancor™ on-line analyzer was developed and a tighter control of cyanide addition was applied. These modifications to the leaching practice significantly reduced cyanide consumption.After a while, it was observed that regulation of « free cyanide » concentrations could still be improved by the use of an automatic control strategy. Yvan-Vézina and CRM began collaborating in 1995 to develop and implement such a strategy. Results show that main disturbances of the circuit (e.g. ore mineralogy and pulp feed rate) can be significantly overcome in order to reduce their effects on the leaching operation."

Jan 1, 1998

By M. Razavi

This investigation is part an overall investigation on the effect of sodium silicate on the properties of the mine backfill. The results presented will highlight the effects of binder dosage, sodium silicate concentration, and pulp density on the performance of stabilized sodium silicate-fortified sand pastefill samples. Binders implemented for these experiments consisted of cement, slag, and sodium silicate in various proportions. The binder content varied from 3 to 9 wt% (total dry weight) and sodium silicate concentrations was adjusted at 2 and 4% (total binder weight). Moreover, pulp density was adjusted to values between 80 and 83 wt%. For completion of the aforementioned phase of the study, series of sand pastefill test samples were prepared and cured for 28, 56, or 120 days, in a humidity and temperature controlled room. The specimens were tested for uniaxial compressive strength (UCS). In order to study the effect of sodium silicate on microstructures of stabilized sand pastefill, some MIP tests were conducted on selected samples. The results of this investigation evaluate the use of sodium silicate as a partial replacement of cement in stabilized backfill. The analyses of the results demonstrates that, with an increase in binder content and a decrease in pulp density, the UCS values of sand pastefill samples increase. Further more, the results indicate that increase in addition of sodium silicate does not necessarily result in higher strength minefill.

May 1, 2007

By A. Y. Senchenko, Y. V. Kulikov

"In recent decades HPGR technology has proven itself in comminution circuits of mining plants. High technical and economic performance, lower specific energy consumption and reliability of HPGR equipment makes it an efficient alternative to conventional circuits using stage crushing and rod/ball milling, as well as to AG/SAG circuits. However, despite all the advantages of this technology the correct selection of key and auxiliary equipment is very important since errors at testing and design stages may lead to discrediting of the whole concept of HPGR application. There is a great variety of possible circuit configurations using HPGR, e.g. with circulation of edge product, with crushing of the whole discharge and circulation of screen oversize, successive two-stage crushing, etc. Each type of minerals will require its own optimal crushing circuit. In this context the testing methodology for selection of an optimal configuration becomes of prime importance. It is common knowledge that the best simulation of material crushing and softening within a HPGR can be obtained only in the course of a large-scale pilot test. The main approaches applied to this kind of testworks are described in this article. Special aspects of HPGR technology design and industrial operation are revealed as well. Some operational issues of HPGR equipment and of circuit as a whole were detected. They are related to regions specifics, plants location, and other factors. Process solutions proposed to deal with these issues are also indicated in the article. INTRODUCTIONDesign and construction of the processing plants involving High Pressure Grinding Rolls (HPGR) technology becomes more and more common in mining as this technology has specific technical and economic advantages against the circuits with autogenous/semiautogenous mills (AG/SAG) and other circuits. The main advantage of the technology is low energy consumption and low operation costs respectively. The presence of microcracks and increased content of fine size fractions in the crushed product contribute to reduction of energy required for further ball grinding. Besides, HPGR technology applies a special wear resistant liner that enables significant reduction of operation costs of grinding media and liner comparing with AG/SAG circuits."

Jan 1, 2016

By A. E. Aho

"The Pacific Nickel property lies 7 miles northwest of Hope and 100 miles east of Vancouver, in the Coast Mountains of southwestern British Columbia. Nickel-copper sulphides were discovered in ultrabasic rocks on this property in 1923 and the deposits were explored by Pacific Nickel Mines until 1937, then again between 1951 and 1954 by Pacific Nickel Mines and by Newmont Mining Corporation through its subsidiary,Canadian Ore DepositsWestern Nickel. The property was studied by C. E. Cairnes (1) in 1924, by W. E. Cockfield and J. F. Walker (2) in 1933, by H. C. Horwood (3), (4) in 1936 and 1937, and by the writer in 1951 and 1952. Except for a few thousand tons for trial shipments, the property has never been mined. Indicated ore reserves now total somewhat over one million tons averaging about 1.4 per cent nickel and 0.5 per cent copper, with lesser values in precious metals and cobalt.GEOLOGIC SETTINGThe nickeliferous ultrabasic rocks form part of the core of a 15-milewide block of Late Palæozoic metamorphic rocks and Mesozoic intrusives which extend north-south between the coast batholith of British Columbia and the Chelan batholith of Washington. Margins of this block are faulted in part against less metamorphosed volcanic and sedimentary rocks largely of Jurassic and Lower Cretaceous age (Geo/. Surv., Canada, Map 737 A, 1942). Serpentinites, suggestive of deep transgressive structure, occur within the block, and also at its east margin along faults which are southern extensions of the regional Yalakom-Fraser River fault zone. Some of the other mineral deposits in the Hope area appear to be spatially related to these major faults.The mineralization at Pacific Nickel occurs almost exclusively within a stock-like mass of ultra basic rocks which mingle with, and partly cut, a larger batholithic mass of genetically related diorites and norites of late Mesozoic age (Figure 1 ). The ultra basic mass consists essentially of fresh, medium-grained hornblendic pyroxenite with peridotitic cores and with a remarkable margin of pegmatitic hornblendite. The most hornblendic rocks appear to be chiefly products of reaction and replacement of the pyroxene and olivine rocks. The mineralization consists of disseminated and massive pyrrhotite, with subordinate pentlandite and chalcopyrite, amongst fresh olivine, bronzite, and, Jess commonly, augite and hornblende. Both the ultrabasics and mineralization are cut by small hornblenditic and dioritic dykes, and by veins and alteration zones."

Jan 1, 1949

By A. R. Farkoosh

Al-Si based alloys have been recently used by automotive industry for highly stressed engine applications. Due to severe working conditions of the engine parts, existing alloys hardly endure high pressures at high temperatures. This necessitates alloy modifications to enhance the elevated temperature performance. In this study, the effects of trace nickel additions on the microstructural and mechanical properties of A356+0.5Cu alloy have been investigated at different aging conditions. Electron probe microanalysis (EPMA), scanning electron microscopy (SEM) and X-ray diffraction (XRD) are used to study the microstructural changes. Aging curves have been obtained by hardness measurement. It was seen that the presence of additional nickel introduced many complex intermetallic phases within the microstructure which led to improved high temperature mechanical and aging response.

Jan 1, 2011

By D. Kulchyski, R. Thibault, D. Lamoureux

"Mine tunneling applications are sensitive to the leakage and friction performance of ducting systems. Improvements in performance can help project economics through reduction in drift height, booster fan spacing, fan electrical power requirement, and deferral of ventilation raise construction. Semirigid plastic ducting has enjoyed significant adoption in mine tunneling in recent years. This paper explores technical properties and performance aspects of this relatively new material application.INTRODUCTIONUnderground mining projects are sensitive to mine development cost and schedule to meet first production—both of which are defined to a substantial extent by mine access construction. The very nature of mine access development requires driving accesses into new areas and even mechanized and automated tunneling methods require ventilation. Until underground airways are connected, allowing a flow-through circuit, ducted ventilation is required to establish ventilation within any single-access (i.e.: dead-end) heading. See Figure 1 as an example of ducted ventilation. Improving performance of ducted ventilation systems impacts project cost and schedule in several ways:For drifts whose height is defined by overhead clearance above haul trucks or tall equipment, smaller diameter ducting will decrease heading size.With higher ventilation flows, activities can be less ventilation-constricted; secondary headings can be worked without restriction, which improves schedule.Given the ability to provide more air for a given fan power, blasting gasses can clear the face and mine more quickly so crews can return to work more quickly - allowing higher advance rates.Lower electrical costs – both due to lower power consumed by fans and with the requirement for fewer electrical stations to power booster fans."

Jan 1, 2019

By E. M. Yates, H. M. Hamilton

"For the assent of any new mining project it is essential to determine a realistic value of revenue from the sale of concentrates.A description of the market factors influencing the concentrate terms will be presented along with a detailed review of historical terms of a smelter contract for zinc concentrates. OverviewFor the assessment of any new mining project it is essential todetermine a realistic value of revenue from the sale of concentrates.This applies at all stages of assessment through to the final feasibilitystudy. In forecasting revenue for a zinc mine the followingfactors must be considered:(a) mill recovery and zinc concentrate grade;(b) metal price forecast for all payable metals;(c) smelter terms; and(d) other selling costs.Normally, data from test work are used to determine mill recovery and concentrate grade.Market forecasting, and indeed all economic prediction is an inexact science and probably will always remain so. We have our econometric models our input/output models and a lot of other tools. But they are of no help in predicting the unpredictable. OPEC&apos;s huge increase in the price of oil was certainly the most dramatic example of this. It had a tremendous effect on the cost of producing most products world wide and on the price of these products. Any forecasts made prior to the OPEC action were obviously proven wrong."

Jan 1, 1994

By G. Azimi, C. A. Ang, F. Zhang

"Nickel recovery from laterite ores generates large amounts of solid and liquid wastes. This is primarily due to the low concentration of Ni (about 1.4 wt%) in the feed ore to the High-Pressure-Acid-Leaching (HPAL) process. It is known that the HPAL residue contains a high concentration of hematite, a commercially important source of iron in the steelmaking industry. However, the balance is natroalunite, containing sulfur, which is a detrimental element in the steelmaking process. Hence, to make the HPAL residue a suitable feed for steelmaking, natroalunite must be removed. The current work is focused on: 1) a thorough characterization of the HPAL residue obtained from Vale, and 2) a systematic investigation of an alkaline leach process to remove natroalunite. The characterization results indicated that there are about 83 and 12 wt% hematite and natroalunite in the HPAL residue, respectively. The leaching results indicate that sodium hydroxide is the best leaching agent, which results in 55 wt% reduction in the sulfur content. The results of this work enable the conversion of an otherwise waste product into a useful feedstock for steelmaking. Furthermore, this project could potentially have significant environmental benefits by reducing the amount of residue produced during the HPAL process.INTRODUCTION Conventionally, crude steel has been obtained by reducing iron ore containing oxides such as hematite (Fe2O3), magnetite (Fe3O4), and wüstite (FeO) in a blast furnace with coke. The product is then refined in a basic oxygen furnace to produce steel with useful properties (McGannon, 1969; Turkdogan, 1978). Steel has been sought for its desirable properties and its application is widespread throughout modern civilizations. Surpassing the growth rate of other materials, the annual demand of steel has increased at a compound growth rate of 5% over the last 20 years (Baddoo, 2008). The global demand for steel was reported to be 1501 Mt in 2016 and demand is expected to double by 2050 (Cullen, Allwood, & Bambach, 2012; World Steel Association, 2016). In recent years, to meet the rapid growth of demand, secondary resources for iron have been identified as strategic sources of iron (Das, Kumar, & Ramachandrarao, 2000; Li, Sun, Bai, & Li, 2010; Matschullat et al., 2000). The residue produced from high-pressure acid leaching (HPAL) of laterite ore has been identified as one of the important secondary sources of iron (McDonald & Whittington, 2008). Laterite ore represents 60% of the world’s nickel resources and accounts for approximately 40-50% of the world annual nickel production (U.S. Geological Survey, 2016). Therefore, the amount of iron residue produced by the process is substantial and its utilization will produce both economic and environmental benefits."

Jan 1, 2017

By T H. Clark, R P. Doig, V. A. Saull, R B. Butler

Terrestrial heat flow has been determined for four boreholes in the Montreal area. The mean value of the results (uncorrected for glacial effects) is 0.790 ± 0.053 x 10-6 cal/ cm2/sec (95 per cent confidence limits). Thermal gradients were determined using a thermistor probe and d-c bridge, and also by a new method using a probe-contained phase-shift oscillator, the output frequency of the oscillator being a function of probe temperature. Thermal conductivity determinations were made on core from the boreholes, using a divided bar apparatus. INTRODUCTION T HIS paper concerns the terrestrial heat flow in the St. Lawrence lowland of Quebec, as determined from measurements on four of the numerous boreholes drilled in this region for gas and oil. The work has been supported by Geological Survey of Canada Re-search Grant 3-58, awarded to T. H. Clark and V. A. Saull. This sup-port is hereby gratefully acknowledged.

Jan 1, 1962

By P. Shibley, P. R. Clarke

Since this was an interim report of the initial operation of a long term project it is not available for publication. It is expected when the project is completed a full report of the work will be published.

Jan 1, 1968

By M. Xian, M. Jahazi, Y. L. Lin

The 2-mm butt joints of ZE41A-T5 sand castings were laser welded at different defocusing distances on two surface conditions (as-cast or machined) using a continuous wave 4 kW Nd:YAG laser system at a power of 2.5 kW and a welding speed of 6.0 m/min. Two welding modes (conduction or keyhole) have been observed. The adjustment of defocusing distance can greatly influence the establishment of conduction or keyhole modes. On the machined surface conditions conduction welding is obtained at a power density of 4.0 x 105 W/cm2. In contrast, keyhole welding is reached at a threshold irradiance of 1.5 x 106 W/cm2. Neither conduction nor stable keyhole modes have been established at a range of power density from 7.7 x 105 to 1.2 x 106 W/cm2 on the machined surface conditions. On the as-cast surface conditions keyhole is obtained at a power density as low as 4.0 x 105 W/cm2 but good surface quality is obtained at a defocusing of +2 mm. The as-cast surfaces require lower power irradiance for the formation of keyholes indicating that they have higher energy absorptivity for Nd:YAG laser beams probably due to coarse surface morphology.

Jan 1, 2004

By D. Kovachevich, M. A. Pfeifer

"A t remote locations typical of mines and associated ore processing plants, diesel electric generators are ideally suited for power plants due to their inherent operating flexibility, efficiency and reliability. In recent years rapid escalation in fuel and related transportation costs has made extensive waste heat recovery from generating sets financially attractive to a much greater extent than previously.The paper outlines key considerations during planning and design stages for utilizing the various waste heat sources available to best advantage. Based on two /980 mining projects built in the Canadian Arctic, data is presented on potential operating and capital costs savings. A review of heat balances, engineering flow diagrams and major equipment selections for process and building heating systems utilizing waste heat is included.IntroductionResource projects increasingly occur in remote areas requiring on-site self sufficiency in electrical power generation. For such projects, the low- or medium-speed turbo-charged diesel engine is very often the preferred choice as a prime mover for the generating sets . It is inherently reliable, has good response to load changes and has comparatively high fuel efficiency over a wide load range . From a project execution standpoint, It is capital cost- competitive and procurement lead-time normally &apos; fits &apos; within tight schedule constraints. In addition, its potential for waste heat recovery is excellent , particularly in northern climates where space heating requirements are usually substantial, and also where there a re requirements for heat for process and plant services.The high cost of fuel , with add-on transportation costs , provides a major incentive to fully exploit the available waste heat recovery potential o f such installations.As a result of the rapid escalation in the price of petroleum products following major crude oil price increases in 1973 and again in 1978-79, liquid petroleum fuels, having the desirable properties of comparatively high heat content and transportability, are no longer &apos;cheap&apos; commodities and have become so valuable that industry has widely undertaken serious conservation efforts.Currently, it appears that petroleum cost trends of the 1970s may not continue, at least in the near term, and that we may see somewhat reduced energy costs for a time. In the longer term , and certainly within the life spa n of major projects, however, it is generally believed to be inevitable that these fuels will be increasingly expensive . Energy costs are today a major operating cost for remote minerals processing plants and will remain so for the foreseeable future.In order to meet the economic challenge posed by high energy costs, future projects should be thoughtfully planned from the outset with the goal of minimizing energy requirements and maximizing the use of waste heat recovery to meet such requirements. There is also considerable potential for significant energy savings by retrofitting of existing installations."

Jan 1, 1984

By Helmut Lerchs

An open-pit mining operation can be viewed as a process by which the open surface of a mine is continuously deformed. The planning of a mining program involves the design of the final shape of this open surface. The approach developed in this paper is based on the following assumptions: 1. the type of material its mine value and its extraction cost is given for each point; 2. restrictions on the geometry of the pit are specified (surface boundaries and maximum allowable wall slopes); 3. The objective is to maximize total profit-total mine value of material extracted minus total extraction cost. Two numeric methods are proposed: A simple dynamic programming algorithm for the two-dimensional pit (or a single vertical section of a mine), and. a more elaborate graph algorithm for the general three-dimensional pit. ASURFACE mining program is a complex operation that may extend over many years, and Involve huge capital expenditures and risk. Before undertaking such an operation, it must be known what ore there is to be mined

Jan 1, 1965

By C. Guo, R. J. Chalaturnyk, M. MacKinnon, J. D. Scott

The Mildred Lake Settling Basin (MLSB) is the largest disposal site for mature fine tailings (MFT) at the Syncrude Canada Ltd. oil sands plant. Over the past years (since 1996), there has been a marked change in the densification behaviour of MFT in the MLSB. Methane-producing microorganisms, known as methanogens, have become very active, and large amounts of biogas (mainly methane) have been produced. Continued field monitoring of the MLSB has provided convincing evidence of the rapid densification process (rapid water drainage from the tailings) at the area with intense microbial activity. This rapid densification has caused pumping challenges in the transfer of fine tailings from the Mildred Lake Settling Basin for the creation of composite tailings. It may also have potential positive effects in accelerating the reclamation of the oil sands fine tailings. A field and laboratory research program was carried out to study the mechanism leading to the rapid densification phenomenon. A review and discussion of the research program is given and some results from the field investigations and small-scale column tests are presented in this paper.

Jan 1, 2007