Search Documents

By S. B. Kang

Magnesium has poor ductility at temperatures lower than 225°C and, as a result, Mg alloy sheets are produced via fairly complex thermomechanical processes consisting of numerous sequential steps of hot (warm) rolling with low reduction and intermediate recrystallization annealing operations. In context of the present study, a simple technology for the fabrication of magnesium sheets by hot (warm) rolling was applied to various magnesium alloys. The misch metal addition in those AZ alloys was done to evaluate the deformation behavior. Tensile tests were carried out for those AZ alloys after applying different heat treatments. The precipitation of ß phase (Mg17Al12 phase) induced different microstructures with various cooling method from solution treatment temperature, and also with various annealing treatment temperatures.

Jan 1, 2006

By L. M. Pidgeon

Introduction The production of magnesium by direct reduction of the oxide has far passed the experimental stage and was responsible for 30 per cent of the recent wartime production of 246,000 tons per annum. This paper describes the small-scale experiments which culminated in a number of the wartime plants. The paper traces the author's early experiments on various direct reduction reactions leading to his choice of the ferrosilicon reduction of dolomite and the realization that this reaction would proceed at a satisfactory rate at temperatures obtainable in metal apparatus. MgO has a standard heat of formation of 146,100 cal. and is therefore one of the most difficult oxides to reduce. However, if advantage is taken of the relative volatility of magnesium metal, thermally unfavourable reactions may be utilized. In reaction MgO + X = XO+ Mg . . . . . . . . . . . . . (1) the removal of Mg as a gas at high temperatures displaces the equilibrium to the right in the face of the unfavourable thermo-chemistry which is inevitable with any X other than calcium metal. If X is carbon, not only is the reaction highly endothermic, but CO is gaseous. A temperature of l,864°C. is required to produce a pressure of one atmosphere of Mg. Between l,900°C. and perhaps 400°C., the back reaction takes place readily and special shock cooling devices are required to recover magnesium from the gaseous mixture. This reaction does not lend itself to small-scale experiments and was not examined by the author. If, in reaction, carbon is replaced by a relatively pan-volatile metal, the oxide of which is also non-volatile and possesses a fairly high heat of formation, a reduction reaction is offered which is free from the difficulties associated with carbon. The typical case of silicon will serve as an example: 2MgO + Si = SiO2 + 2Mg (g) . . . . . . . . . . . . . . . . . . . . . . (2) At temperatures above l,000°C., a positive pressure of magnesium will exist over the system. Removal of the magnesium vapour will displace the reaction to the right in the face .of an unfavourable thermal balance. Since magnesium is the only volatile component at this temperature, it may be evolved and condensed, using attractively simple distillation technique.

Jan 1, 1946

By A. Mcdonald, F. W. Breaks, T. F. Morris, S. A. Averill, D. C. Crabtree

Gahnite, a zinc-bearing spinel, is a resistate mineral that may be used as an indicator mineral of polymetallic deposits in high-grade metamorphic terrain. The Ontario Geological Survey recently completed sur?cial mapping and sampling programs in the Separation Lake area of north-western Ontario and Kinniwabi Lake area of northeastern Ontario in which gahnite was recovered from samples of sur?cial sediments. Ternary plots of the composition (ZnO, MgO, FeO[t]) of gahnite recovered from these sur?cial studies reveal three distinct groups: Group 1 is characterized by low (< 1 wt%) MgO values; Group 2 by higher (>1 wt%) MgO values; and Group 3 by higher FeO(t)values than Groups 1 and 2. The composition of in situ gahnite recovered from volcanogenic massive sul?de mineralization, Zn-rich Sedex-type mineralization and peraluminous rare-element mineralized granite and pegmatite also was determined. The composition of the gahnite obtained from sur?cial samples was compared with that of in situ material. Gahnite from the peraluminous rare-element granite and pegmatite overlapped very well with sur?cial gahnite of Group 1. Gahnite from volcanogenic massive sul?de mineralization and Sedex-type mineralization overlapped well with sur?cial gahnite of Group 2. These results suggest that determination of gahnite composition in indi-cator mineral surveys may be useful in exploration programs when assessing the mineral potential of a region.

Jan 1, 1997

By A. Mcdonald, F. W. Breaks, T. F. Morris, S. A. Averill, D. C. Crabtree

Abstract-Gahnite, a zinc-bearing spinel, is a resistate mineral that may be used as an indicator mineral of polymetallic deposits in high-grade metamorphic terrain. The Ontario Geological Survey recently completed surficial mapping and sampling programs in the Separation Lake area of northwestern Ontario and Kinniwabi Lake area of northeastern Ontario in which gahnite was recovered from samples of surficial sediments. Ternary plots of the composition (ZnO, MgO, FeO[t]) of gahnite recovered from these surficial studies reveal three distinct groups: Group 1 is characterized by low (< 1 wt%) MgO values; Group 2 by higher (>1 wt%) MgO values; and Group 3 by higher FeO(t) values than Groups 1 and 2. The composition of in situ gahnite recovered from volcanogenic massive sulfide mineralization, Zn-rich Sedex-type mineralization and peraluminous rare-element mineralized granite and pegmatite also was determined. The composition of the gahnite obtained from surficial samples was compared with that of in situ material. Gahnite from the peraluminous rareelement granite and pegmatite overlapped very well with surficial gahnite of Group 1. Gahnite from volcanogenic massive sulfide mineralization and Sedex-type mineralization overlapped well with surficial gahnite of Group 2. These results suggest that determination of gahnite composition in indicator mineral surveys may be useful in exploration programs when assessing the mineral potential of a region.

Jan 1, 1997

By Ray Mason, Damien Label, Howard Bernier, Kevin McDermott, Kevin Coombs

"GeneralWabush Mines is an unincorporated joint venture of seven steel companies and Pickands Mather & Co. The mining and concentrating facilities are located in southwestern Labrador and the pelletizing and shiploading facilities are at Pointe Noire, 200 miles south, near the town of Sept-lies.The operation is based on a 5 ½ sq. mi. specular hematite deposit with a reserve of 375 million tons of concentrate. Annual production capacity is rated at 6 million tons of pellets per year. The final upgrading process utilizes high-tension separation of silica following wet autogenous grinding, spiral gravity separation and fluo-solids drying. The concentrate is railed in closed cars to Pointe Noire. The concentrate is reground dry and pelletized on Dravo Lurgi travelling grate machines to produce an oxide pellet with 65.5% Fe, 3.0% Si02, 1.95% Mn and 93.5% Tumble Index.HistoryPlant operations commenced in 1965 with a concentrator capacity of 5.3 million tons per year and a pelletizing capacity of 4.8 million tons per year. The original facilities for classifying the crude ore into fine and coarse fractions for storage purposes before reblending as autogenous mill feed were found to be unnecessary and were by-passed after plant startup. Capacity of the operation was increased to 6.0 million tons of pellets per year in 1968. This increased capacity required the installation of an additional160 cleaner spirals in the ore dressing plant, a new 5000 hp ball mill, three balling circuits and increased cooling air capacity in the pellet plant.In 1970, the regrind circuit in the pellet plant was converted to dry grinding and a significant reduction in grinding media consumption and maintenance costs was realized. A ninth grinding mill of 5000 hp capacity was installed to compensate for the reduced capacity in going from wet to dry grinding."

Jan 1, 2000

"Pilot plants for pressure hydrometallurgy represent special design and project execution challenges. Over the past twenty years, Zeton has designed and fabricated a variety of world-class pressure hydrometallurgical pilot-plant facilities for the nickel industry, and this paper discusses design considerations and strategies related to such projects. Project execution methods are also discussed, and guidance is given for the selection of materials of construction and for the selection of appropriate pressure and temperature design points for pressure hydrometallurgical pilot equipment. The paper concludes with a discussion of the need for process similarity with future commercial operations and the realities of pilot-scale equipment.INTRODUCTION The process technology developer or owner and the designer/fabricator of a new pilot-plant facility are faced with some difficult technical choices even after the decision to build a dedicated plant has been taken. A pilot-plant project is usually on the critical path of a large commercial project involving investments many multiples greater than the capital cost of the pilot plant. Schedule savings in the design, manufacture, and commissioning of the pilot plant or in a rapid completion of the experimental program can be disproportionately beneficial to the overall development project. However, inappropriate shortcuts resulting in major oversights can be disproportionately problematic. A number of considerations and suggestions for both the project execution approach and the process engineering design of pressure hydrometallurgical pilot-plant facilities are presented as a guide for potential owners and operators of new pilot-plant equipment and facilities. These suggestions are particularly applicable to the nickel industry, where the majority of our firm’s prior hydrometallurgical experience was obtained. This paper is an update to an earlier publication (Martin, 2004), offering an opportunity for a new generation of metallurgists and engineers to learn the specialist requirements of pilot- and demonstration-scale plant design, which are key functions in the development and commercialization of new processes."

Jan 1, 2017

By R. E. Johnson

Seventy years after the start of the Industrial Revolution in Great Britain, as reckoned from Arkwright&apos;s water frame patented in 1769, there was a significant development of the metallurgical industry in Virginia. In Britain, crucible steel had been rediscovered by Benjamin Huntsman in 17~0, and this made spring and tool steel more generally available. The metal-turning, screw-cutting lathe, including the basic principles recognized in today&apos;s engine lathe, was developed by Henry Maudslay about 1797. Wrought iron, as manufactured by Henry Cort&apos;s process patented in 1784, was readily available. Richard Trevithick&apos;s highpressure steam locomotive had met its test on the Pennydarren tramroad in 1804, and George Stephenson had built his famous Rocket, along with several other locomotives, at Newcastle around 1828. Puddling furnaces and a rolling mill had been placed in operation at the Tredegar Iron Works in Glyn Sirhowy, Monmouthshire, Wales, in 1807. In the United States, expanding commerce and a growing population resulted in continuing development from the Chesapeake to Virginia&apos;s Blue Ridge, and this demanded improved means of transportation. Ore deposits rich in hematite had been found in Virginia&apos;s Piedmont during the Colonial period, and a number of blast furnaces now dotted that area. The products of these operations were mostly pots, kettles, stove parts and like items for local trade. The James River and Kanawha Canal was incorporated in January 1785. Its eastern leg, winding along the slope of the high bluffs overlooking the river, was completed about 1800. About two dozen railroads were chartered in Virginia between 1830 and 1837. With expanding population and steady industrial development came a need for metallurgical products. Throughout the eastern United States, numerous metallurgical enterprises sprang up, and many of these flourished. The purpose of this article is to outline the development of one Southern metallurgical company, the Tredegar Iron Works, which was to have a significant impact on the industrial development of Virginia and the fighting of the American Civil War. Although the Tredegar Iron Works no longer exists, remnants of the early operations have been restored, and the current status of the site is also presented.

Jan 1, 1999

By P. O. Sandstrom

"Atlas Copco is introducing a new patented method for full-face boring. This paper presents the basic principles of the boring action and discusses the present experience regarding performance and costs. The Atlas Copco ""Full-facers"" are designed for hard-rock applications, although they are successfully boring in soft ground without major changes. The unique patented boring principle referred to as the 'Undercutting Method' permits these machines to bore, economically, in harder ground than machines based on the 'crushing principle'. This is mainly due to considerably lower cutting-tool costs, as the tungsten carbide tips only are in contact with one-third of the bored volume. The remaining rock is 'undercut' and peels off from a slight back pressure.The undercutting method also permits boring of non-circular headings and Atlas Copco has already manufactured two machines for rectangular drifts. This concept could revolutionize development work in mines employing trackless equipment."

Jan 1, 1971

By James D. Hall

THIS essay deals with the materials and methods used in the waste filling of scopes in Canadian mines, with especial reference co the methods used at the Sullivan mine, Kimberley, B.C. The author would like to thank members of the staff of the Sullivan mine for information obtained, and acknowledges material from the following publications: Waste Filling of Stopes: Information Circular 6816, U.S. Bureau of Mines. Mining Methods and Practices at Lake Shore, by Leslie S. Weldon; Trans., C.I.M. & M., Vol. XXXIX, 1936, pp. 142-202. Development and Mining (at the Mcintyre Mine), by D. E. Keeley; Eng. & Min. Journal, November, 1933. INTRODUCTION Although mining in Canada is a relatively youthful industry, many of our mines have reached a stage of extraction which requires waste filling, both as a means of support and co make possible the winning of ore that would otherwise have co be left in the mine. Fill may be used at regular intervals as one of the cycle of operations, as in cur-and-fill and square-set scoping; or it may be introduced into a completed stope co provide permanent support for overlying rock formations, and co permit mining of pillars of valuable ore. Waste fill is sorted in resuing, which is a form of cut-and-fill scoping employed in narrow veins.

Jan 1, 1937

By D. H. Flather, J. W. Hendry, K. Drover

Black Hawk Mining Inc. has completed a comprehensive program on the prediction and management of acid rock drainage (ARD) at their Keystone Gold Mine (Keystone) near Lynn Lake, Manitoba. The program, initiated in 1994, followed a phased approach utilizing initial acid-base accounting (ABA) results and subsequent laboratory kinetic testwork to define site-specific sulphide oxidation and neutralization consumption rates in waste rock. Net acid generating waste rock at Keystone was defined through the kinetic testwork as waste rock yielding a net potential ratio (NPR) of less than two. A preliminary waste rock management program based on blending of potentially acid generating and acid neutralizing waste rock was advanced. Subsequent refinement of the management program followed the analysis of over 1580 ABA samples collected from individual blast holes during the initial bench development phase of the Keystone pit. Uncertainties in actually achieving adequate blending within the dumps at a mining- scale resulted in the development of a revised waste rock management program based on segregation. Recognizing that any successful management plan requires that the ARD characteristics of the waste rock be identified prior to in-pit blasting, the extensive ABA database was utilized to develop a rapid characterization scheme. By implementing a characterization scheme based on total sulphur concentrations and fizz rating, waste rock could be quickly segregated without delaying the natural flow of ore from the pit. Interestingly, it also became apparent that gold values were strongly correlated with total sulphur, such that traditional fire assays were supplanted with a simple and more cost-effective total sulphur determination. The program highlights the importance and benefits of collecting and exploiting data beyond that necessary to acquire appropriate development permits.

Jan 1, 2000

By A. W. Jolliffe

AEROPROSPECTING may be defined as the application of the air view to the search for mineral deposits. The term is suggested as a preferable alternative to either aerial prospecting (which may be confused with areal prospecting) or air prospecting. The air view may be obtained by visual observation from an aircraft or by examination of air photographs; each has its particular advantages and disadvantages. Aeroprospecting should be regarded only as an aid to, and not as a substitute for, accepted prospecting methods ( l ). The Precambrian region north of Great Slave lake consists of two well defined physiographic units, a feature first noted by J. T. Wilson (2). The boundary between these lies close to the north shore of the east arm of the lake and extends northwesterly near Spencer, Beniah, Carp, and Ghost lakes (Figure 1). South and west of this line, exposed bed-rock makes up the greater part of the land area; eskers are very rare, and overburden is largely limited to rock-walled valleys and depressions. North and east of the line, outcrops are rare or absent, eskers are abundant, and most of the surface consists of drumlin-like drift hills, elongated parallel to the direction of ice movement (Figure 2). Where this boundary passes through the area shown in Figure 1, it lies near the 1,200-foot contour and may mark the maximum extent of the lake or sea arm present in this vicinity toward the end of the Pleistocene period. For convenience, the first area may be called the &apos;bed-rock belt&apos; and the other the &apos;drift belt&apos;.

Jan 1, 1945

By Habib Zughbi, Paul Zulli

"A key step towards sustainability in iron and steelmaking is to optimise the use of raw materials and energy consumption, and consequently minimise CO2 emissions. Models based on a Process Integration (PI) approach play a key role in evaluating various scenarios and the impact of introducing changes in raw materials and operational conditions on the overall energy consumption and CO2 emissions. BlueScope uses a PI based comprehensive model for its Port Kembla Steelworks (PKSW), called the Integrated Steelworks Energy and Emissions Model (ISEEM). ISEEM is tightly coupled to the configuration of PKSW. It is based on mass and energy balances as well as thermodynamic relationships. ISEEM is a steady-state model and is used to predict overall and detailed unit-by-unit energy consumptions and CO2 emissions. It is also used for plant-based scenario modelling. This paper investigates the impact of major changes to PKSW configuration, including the shutting down of a blast furnace and cokemaking battery, on the energy consumption and CO2 emissions of the plant. It discusses some of the issues involved in updating the model and some identified opportunities."

Jan 1, 2015

By J. McCreedy

"The addition of Portland cement to hydraulic sand fill has resulted in the production of stable and self-supporting cemented sand fill. The use of cemented fill in the mines of The International Nickel Company has resulted in substantial economies in timber requirements, de-creased dilution of ore and greater flexibility in mining methods.Coupled with special mining techniques, it has permit-ted mining by both cut-and-fill and shrinkage stoping methods to much greater depths than heretofore. The use of cemented sand fill has permitted revisions to undercut-and-fill mining which have significantly improved the efficiency of this method.Automated mixing systems have been developed for preparing cemented sand fill in surface sand plants on a continuous throughput basis. Control of cement-sand mixtures is obtained by the use of a mass flow measuring system and weighing cement feeders."

Jan 1, 1966

By V. Aprahamian, T. Cheng, M. Tangen, R. Beauprie

The Royal Canadian Mint has implemented significant process additions since 2005. Installation of a whole new highly automated silver refining circuit has allowed recovery of physical silver from gold and silver dorés . To complement this change, a small Top Blown Rotary Converter has been in operation. On the gold refining side, a new hydrometallurgical process to recover precious metals from Miller Chlorination slag has been developed. Finally, new systems have been put in place to improve treatment of waste water, wet and dry fume and dust.

Jan 1, 2011

By Jianglan Duan, Steve L. Cockcroft, Andre B. Phillion, Carl Reilly, Daan M. Maijer

"In the aluminum alloy wheel casting process, careful design of the cooling system in the die and its operation (cooling channel timing) are critical to achieve quality and productivity goals. The problem is challenging owing to the cyclic nature of the process and the relatively large thermal mass of the die in comparison to the wheel. For a given die geometry, a set of constraints have been defined to ensure directional solidification and an objective function, based on cooling rate during solidification, has been defined to reach a target secondary dendrite arm spacing. The methodology presented in this study employs the commercial finite element package, ABAQUSTM, and an optimization module based on the open source library, Scipy. The developed methodology has been applied to a series of geometries and cooling system configurations, including a 2-D axisymmetric wheel and die assembly generated from a prototype die. Preliminary testing has shown that careful selection of the objective and constraint functions have made it possible to reach desired solidification pattern.TM- Dassault Systèmes Corp."

Jan 1, 2014

By Hugh M. Roberts

DEVELOPMENT at Steep Rock lake has given rise to renewed interest in the geology of the iron ore deposits in the Lake Superior Region and has implications of no small moment bearing upon methods of exploration in the Precambrian Shield generally. Following upon the Regional Lake Superior meeting of the American Institute of Mining and Metallurgical Engineers in August, 1941, the authors prepared a paper on the Steep Rock deposits, which appeared in the A.I.M.E. publication, Mining Technology, for January, 1943. Between Januar7 and April, 1943, exploration at Steep Rock was continued by means o vertical, Mesabi-type churn-drill holes put down from the ice. This drilling has enlarged the tonnage of ore previously known and has disclosed further facts relating to the origin of the ore. The added evidence, we believe, goes to support the hypothesis that the deposits were formed by a process of replacement due to upward-moving, iron-bearing solutions which came in as igneous after-effects. Accordingly, in presenting the subject to the Canadian Institute of Mining and Metallurgy, it seems best not to change our first explanation, but to prefix the original paper with an interpretation of the results of the more recent explorations completed after its publication.

Jan 1, 1943

By C. Droun

"Low back pains account for about 13 per cent of all compensation claims made to the Quebec Workmen's Compensation Commission and cost the employers a sum exceeding ten million dollars. The frequency and cost of these health problems in Quebec metal mines are proportional to the provincial trends. An elaborate review of the literature on the causes, nature and prevention of low back pain is made in this presentation. A prevention program for low back pain has been designed in cooperation with a team of seven medical specialists and two physiotherapists for the Quebec metal mines. The program is especially designed for persons who have had low back pain, in order to prevent a recurrence, and for persons beginning to feel chronic difficulties. It is based on existing programs at the Hawthorne Plant of Western Electric Company and at Minnesota Mining and Manufacturing, but it requires a much different approach because of the nature of medical care available at the mining sites. The program is difficult because it involves a change of attitude for every employee and every supervisor. The program, so far, is beneficial because several men are now seriously engaged in an active program of reconditioning and because the problem of low back pain ie beginning to be seen from a new angle."

Jan 1, 1973

By P. Amelunxen

It is well-known that the particle breakage mode that occurs in a semi-autogenous mill is significantly different from that which occurs in a ball mill, enough so to warrant very different lab scale breakage tests and scale-up models. This phenomenon, at the plant scale, leads to changing process constraints depending on the particular properties of the ore. For example, hard or coarse ores might bottleneck the SAG/AG mill throughput, while the ball mills might constrain throughput when milling soft or fine ores. Because the power draw of a ball mill is fairly constant compared to that of a SAG/AG mill, periods of SAG/AG mill bottlenecks lead to increased ball mill circuit specific energy consumption and a finer grinding circuit product size, which together constitute a loss of efficiency of the overall process. Because HPGR circuit throughput is less sensitive to changes in ore hardness, this situation is less common or severe in those circuits. Furthermore, the ball mills are somewhat decoupled from the upstream crushing circuits through the use of surge bins, which also helps to mitigate this effect. As a result, ore hardness variability constitutes a significant cost penalty that should be applied to SAG mill/ball mill/pebble crusher SABC circuits when evaluating the relative economics of different grinding circuit configurations. Nevertheless, the issue is by-and-large ignored, because most current HPGR trade-off studies are based on averaged ore hardness parameters. This paper provides an estimate of the magnitude of this penalty for a typical operation by using Monte Carlo simulation methods and plant data from Freeport-McMoRan?s autogenous, semi-autogenous, and HPGR-based comminution circuits. A case study from an in-house 96K t/d sulphide project is presented to illustrate the concept. It was found that by including variability effects, the trade-off NPV of the HPGR circuit over that of the SAG mill circuit increases to $84 million from negative $33 million, effectively reversing the original decision of selecting a SAG mill circuit for the fixed hardness case.

Jan 1, 2012

By R. D. Brown

The first step in achieving a rationalization of Canada&apos;s crazy patch-work quilt of mining taxes and policies was achieved with the release last November of a major federal-provincial report on the taxation of the Canadian mining industry. The Report, prepared by a group of federal and provincial civil servants, sets out a concise and informative discussion of the major taxation and incentive issues facing the mining industry, and puts forward major recommendations for more rational and moderate taxation policies. It will be considered by federal and provincial Finance and Resource Ministers for possible action by the respective governments. The Report was prepared in response to a directive from the federal and provincial First Ministers in February 1978 to review the federal and provincial taxation of the resource areas. Although the Report is more successful in identifying problems rather than concrete solutions, and reflects some continuing differences of opinion between the governments involved, it does represent an important first step in a comprehensive review of our resource tax policies. This article summarizes the Report, which is some sixty pages in length. Although a detailed discussion of it is beyond the scope of this article, the report itself is recommended reading for those concerned about the current state of the Canadian mining industry.

Jan 1, 1979

By E. Adam, B. Milkereit, M. Salisbury, L. E. Reed, G. Perron

Integrating seismic reflection, borehole geophysical, and physical rock property studies is an effective means of mapping lithological contacts and structures in the crystalline crust. At Les Mines Selbaie in the northern volcanic zone of the Late Archean Abitibi Subprovince, a high-frequency seismic reflection profile has provided the first images of deep crustal structures of this important polymetallic mine site. Physical rock property and borehole geophysical studies confirm that prominent seismic reflections can be caused by lithological contacts, faults and sulphide mineralization. At Les Mines Selbaie, the first two of these are shown by this study. Clearly identifiable reflection images from sulphide mineralization have not been demonstrated in analysis of the profile. The seismic images provide useful information about gross structure in the vicinity of Les Mines Selbaie. They can also place important constraints on the sequence of tectonic events and, therefore, can aid future deep exploration programs.

Jan 1, 1997