Search Documents

A study is presented of the theoretically possible initiation systems for outbursts and the subsequent propagation mechanism.Previous occurrences of outbursts and their correlation to the theoretical system are described. An estimation of the energy release from two energy sources, gas strain energy and rock/coal strain energy, is presented and the relative importance of each source in the severity of outbursts. Summary: The description of mechanisms of outbursting follows the examination of these phenomena at Collinsville in Bowen No. 2 mine and at Leichhardt Colliery, Blackwater. Quantitative material contained in the paper refers to Leichhardt Colliery, Blackwater. Clearly from the work carried out to date gas release has a major part to play in the out- bursting at both of these collieries. In the case of the December 1 1978 outburst at Leichhardt Colliery energy release estimates place gas strain energy release contributing eight times the energy of that from rock/coal strain energy. Even the normal outbursts at Leichhardt Colliery appear to show this trend. Estimates of energy released are for comparative purposes between gas and rock strain energy and the values obtained may be regarded as approximate.

Jan 1, 1980

The stratigraphic sequence west of Mount Isa contains the Judenan Beds, Eastern Creek Volcanics, and May Downs gneiss. It is an incomplete sequence as major north-south faults divide the area into four separatezones containing portions of these different units. The first three zones, which occur directly to the west of the Mount Isa Fault, consist of quartzites and quartz-mica schists which are uncorrelatable between zones but have been grouped together as the Judenan Beds. The most western zone contains an incomplete section of Eastern Creek Volcanics which rests conformably on a unit believed to be equivalent to the Mount Guide Quartzite; this is again underlain by the May Downs gneiss. A detailed description of the rock types is presented, but only a broad stratigraphic correlation is possible with the very much thicker sequence to the east of Mount Isa.The age of sedimentation is believed to be Lower Proterozoic and it may not occur in the type of geosynclinal basin envisaged by previous authors.This sequence is intruded by many small basic intrusions and also the Sybella Granite with its associated microgranite and pegmatites. The Sybella Granite consists of both a massive and a foliated phase; the latteris generally restricted to the margin of the main granite mass.Four regional metamorphic zones have been identified on the basis of their pelitic mineral assemblages; these are a chlorite, biotite, biotite-cordierite, and a sillimanite zone; separating each are prominent north-south faults.This metamorphism is a regional metamorphism which accompanies the first generation folding of the area and is not associated with the emplacement of the Sybella Granite. A very localized retrogressive metamorphism is also found in some areas of second generation folding.

Jan 1, 1972

Cerro Matoso (CMSA) in Colombia produces ferro-nickel from lateritic ore containing approximately three per cent nickel, using a Rotary Kiln - Electric Furnace (RKEF) process, in which the calcining of the mineral within the kiln is second in importance only to the smelting of the mineral in the Electrical Furnace. This article discusses the installation and operation of an expert system to control the kiln of CMSA. In the CMSA process, the run-of-mine ore is crushed, homogenised, dried and mixed with a small percentage of coal, before being heated up to 900¦C in a rotary kiln in the presence of natural gas mixed with air in a controlled proportion (air/gas constant ratio). The final objectives of the process are the following: ò To reduce to a minimum the iron and nickel oxides in order to convert these into metallic ions; this is a reduction process to facilitate largely the smelting in the electric furnace. Since the reduction is made with natural gas, it is much more economical than the subsequent complete reduction in the electric furnace, since electrical energy is much more expensive by unit of processed mineral. ò To heat the mineral as much as possible to facilitate the subsequent smelting. ò To eliminate totally the moisture content of the ore. An expert system with fuzzy logic was commissioned in 1994 for the control of the kiln and it has operated with good results ever since.

Jan 1, 1996

The problem of manufacturing from sulphuric 'acid and Christmas Igland "A" phosphate, superphosphate of acceptable physical condition and agronomic phosphate availability, is directly related- to the crystallisation of a reac- tion product, monocalcium phosphate monohydrate. Two solutions to the problem, vacuum drying the superphosphate and calcination of the ore before reaction with acid, are discussed.

Jan 1, 1971

By Hatherly P, Dunn P

There are- several in-seam coal research projects currently under investigation by the Cooperative Research Centre for Mining Technology and Equipment (CMTE). The overall aim of the projects is to produce new technologies to enhance safety and the efficiency of in-seam gas drainage drilling. Results from high pressure waterjet rotary drilling trials indicate that by applying high pressure water to a rotary drill bit, the hole can be drilled to follow the planned trajectory very closely. Steerable drill bits for drilling long holes (>1 km) have been produced and trialed. A flexible high speed drilling system provides a capacity for rapid in-seam drilling, particularly suited to cross panel drainage. Geophysical tools are being developed to provide a geological steering capability and a better understanding of potential gas outbursts zones.

Jan 1, 1998

By P D. Franzmann, D J. Readett, J Peterse

A better connection between laboratory- and pilot-scale test results, and heap bioleaching performance can be achieved by generating reliable information on the fundamental microbial, chemical and physical processes that occur in heaps and incorporating this information into a comprehensive and robust model. More efficient heap bioleaching, particularly of chalcopyrite, has the potential to add value to the mining industry as well as deliver attractive environmental and social benefits to the communities within which those companies operate.The results of fundamental chemical and microbiological studies of the leaching mechanism, the temperature dependence of chalcopyrite bioleaching, and the optimisation of leaching conditions are described with examples from full-scale heaps. The development and application of a number of novel techniques and tools has assisted our understanding of heap subprocesses mineralogy, hydrology, chemistry and microbiology. The heap bioleaching model HeapSim, which embodies a large number of effects not previously accounted for in other models, continues to be refined and has been applied successfully to the study of several heap bioleach systems.

Jan 1, 2004

By P Andrieux

By 1996 ground control-related problems at Brunswick Mine had raised serious concerns regarding the safe and economical extraction of large portions of the reserves. These difficulties were mainly caused by high stress levels in pillars, instabilities resulting from wide spans supported by ageing support elements, and chronic difficulties supplying rock fill from the surface quarry to the underground workings, which resulted in many large voids remaining open for long periods of time. Significant changes have been implemented at the site since 1996, amongst which were a change of mining method, the introduction of paste backfill, the establishment of stress management measures, and the introduction of shotcrete on a large-scale. This paper focuses on the regional ground conditions associated with both the previously used primary-secondary mining method and the newly implemented pyramidal pillarless technique, as well as on some of the stress management measures implemented at the mine.

Jan 1, 2000

Before commencing design of a coal prepar ation plant, it is essential to have detailed information of the raw coal to be treated to- gether with a clear understanding of the products required. Prediction of raw coal size distribution, particularly the amount of fine material, is difficult and the methods employed should be large scale pilot plant studies or techniques to simulate coal degradation and shale breakdown in water. A detailed knowledge of well proven coal preparation processes and new developments allows processes and process combinations to be compared to'obtain the maximum economic recovery when using lower cost, less efficient processes within acceptable limits. Equipment should be selected bearing in mind its precise application and the location where it is installed. Plant layout should be carefully studied to minimise equipment requirements and to simplify construction. Measurement, control and automation should be an integral part of plant design in order to obtain the optimum performance of the processing equipment.

Jan 1, 1974

By Turner T. M, Jorgensen F. R A

The tendency of the concentrate to ignite was studied using four techniques, namely, laminar flow furnace, fluid bed, thermal analysis and boat-in-furnace. Exothermic activity occurred at two temperatures: minor activity in the vicinity of 200¦C, major activity at 330-350¦C. The low temperature reaction was due to the ignition of a small amount of free sulphur while the major activity was associated with the ignition of the sulphide minerals, notably pyrite. To avoid ignition of the sulphide minerals, the gas temperature should not exceed 300¦C and the oxygen content of the gas phase should be as low as possible. It was shown that little of the arsenic in the concentrate entered the gas phase during drying.

Jan 1, 1987

By Marshall GA

Structural fatigue damage of haul truck frames is a costly problem associated with the operation of large mine haul trucks. A monitoring programme is described which has been instigated to measure stresses in the frames of haul trucks under actual mine operating conditions. The instrumentation used and methodology employed in the computer analysis of the results is briefly described. The results of the monitoring programmes are reviewed, and the effects of various factors affecting structural fatigue damage of three common types of rear dump truck are considered. Factors discussed include the effects of haul route features (for example shovel, dump and crusher areas); the effect of operations such as turning, braking, loading and dumping; the influence of payload; the effects of malfunctions in suspensions; and the influence of haul route surface quality. It is shown that with respect to payload, while structural fatigue damage is increased with payload, the structural damage per unit of payload does not change significantly for moderate increases in payload above the nominal value. Finally, on the basis of these results, recommendations are made for haul route design and operational practices which will increase the structural fatigue life of haul truck frames.

Jan 1, 1986

During the past 18 months several import- ant hydrocarbon discoveries have been made in the Dampier Sub-basin, which is a sedimentary area lying entirely offshore from the Precambrian Pilbara Block in the southern part of 'he Northwest Shelf of Western Australia. This sub-basin is a major sedimentary downwarp forming a northern extension to the Carnarvon Basin. This extension is bounded to the north by the De Grey Nose, separating it from the Beagle Sub-basin. To the south the Dampier Sub-basin merges with the Barrow Sub- basin. Extensive seismic data combined with results from exploration drilling show that the Dampier Sub-basin is a complex depositional basin containing over 20,000 feet of sediments which are mainly Triassic to Recent in age. Tectonically the sub-basin can be divided into seven main structural elements. In a northwest to southeast direction these are the Rankin Platform, the Kendrew Trough, the Madeleine- Dampier Trend, the Lewis Trough, the Legendre- Rosemary Trend, the Enderby Fault Zone and the broad Pilbara Shelf. Permian sediments were encountered in only one well drilled to date in the sub-basin, but Triassic and younger sediments are extensive. The section consists initially of 'hi -_D 7 ri ,~ ~, , i , Derived

Jan 1, 1973

By L O. ÆNeill, J Bebek

When Kalgoorlie Consolidated Gold Mines (KCGM) purchased its fleet of 18 CaterpillarÆs dump trucks in 1999, as part of its change to owner operated mining, five CaterpillarÆs Computer Aided Earthmoving Systems (CAES) were also commissioned on Komatsu PC8000 hydraulic shovels and Caterpillar D10R bulldozers. Since then the CAES system has been installed and operational on Komatsu PC3000 hydraulic shovel, CaterpillarÆs D10R dozers and Cat 994 front-end loader while Cat 854 wheel dozer has been fitted with CAESbasic. This investment in advanced machine guidance and control technology has proven very beneficial over the years for the Super Pit with improved safety and increased operating efficiency and productivity. The paper brings into focus how the CAES system adaptation in unique mining conditions assists in production gain, equipment operatorÆs safety, flexibility and independence, personnel removal from hazardous areas, acquisition of operational information and improvements in mine planning and design, benefiting the entire mining operation.

Jan 1, 2003

By H Nikraz, E Jamieson, D Cooling

The use of red sand as fine aggregate in concrete manufacture has been investigated as well as the use of fly ash as a cement replacement. The experimental work consisted of casting various concrete mixes including a control and comparing standard properties. Properties tested included compressive strength, splitting tensile strength, flexural strength, modulus of elasticity, water permeability, chloride diffusion, pH dependence leaching and particle morphology. The results show that the concrete strength is not significantly affected when natural sand is replaced completely with red sand. The durability tests indicated high water permeability and high chloride diffusion due to the porosity of the red sand concrete, likely due to the low slump value. Leaching tests did not exceed New South Wales EPA guidelines.

Jan 1, 2006

By Yesil MM, Bozdag T

This paper describes the conver- gence and load measurements carried out in inclined seams at five longwall faces, two of which were supported by hydraulic props and the other three by conventional timber supports in Karadon-Gelik mine. The minimum support capacities determined in this study are compared with the results obtained from two empirical approaches suggested by Wilson (1975) and Jacobi (1981). The characteristics of hydraulic props to be used and support patterns in the longwalls are found, conclu- sions are drawn and suggestions are made. Design nomograms are prepared for field engineers, in order to be able to approach the problem more confidently and realistically.

Jan 1, 1992

By Tiu C, Sarmiento G, Uhlherr PHT

Fundamental rheological properties of slowly settling mineral slurries are reviewed. Slurry flow is discussed in terms of observed shear stress-shear rate behaviour. Particular emphasis is placed on establishing procedures for scale-up and design. Flow property measure- ments on red mud, a waste product from the Bayer alumina process, are presented and used to illustrate recommended design procedures.

Jan 1, 1978

Kalgoorlie Consolidated Gold Mines Pty Ltd (KCGM) is a management company, formed in 1989, to manage the assets and operate the Kalgoorlie joint venture for the owner companies Gold Mines of Kalgoorlie Limited (GMK) and Homestake Gold of Australia Limited (HGAL). Mining is still in progress on the 'Golden Mile' and surrounding areas more than 100 years after Paddy Hannan's discovery adjacent to the active Mt Charlotte mine. From 1893 until 30 June 1995 the Kalgoorlie Goldfields has produced approximately 45 million ounces (-1400 tonnes) of gold from mining and treating about 179 million tonnes of ore. This production equates to about 20 per cent of the total Australian gold production and about one per cent of the world's

Jan 1, 1996

By Stille H

The choice between drill and blast and mechanical boring methods is often not obvious. There are several factors which may have a de- cisive influence on this choice, such as the geometry and length of the tunnel, site con- ditions and borability of the rock. Both the un- confined compression strength and the joint dis- tance have a considerable influence on the net penetration rate. Site conditions, rock quality and water conditions influence the utilization of the tunnel boring machine. The drill and blast method is normally less sensitive to devi- ations from assumed ground conditions.

Jan 1, 1987

By Medhurst TP, Trueman R

The aim of the paper was to model numerically some aspects of the extraction of coal pillars by split and fendering. A two-dimensional elasto-plastic plane strain model with strain softening and interface mod- elling was used. The model was able to simulate the improvement of conditions experienced in lifting from the fender, when the roof adjacent to the fender has caved. In contrast, when a stook was left, providing support to a span of uncaved roof, the model pre- dicted the fender would suffer considerably more de- formation and strain.

Jan 1, 1992

By Le V, Nguyen Ngoc Quynh, R H. Murfitt

The Truong Son Fold belt in Indochina hosts the significant Sepon gold-copper district (Laos) and the similar gold-basemetal districts of Phuoc Son and Bong Mieu (Vietnam). With over seven years of exploration, Toronto-listed Olympus Pacific Minerals Inc, is one of few foreign companies that have to date made a substantial investment in mineral exploration in Vietnam.Much of this work has been conducted along the Phuoc Son û Tam Ky Suture, on the south-eastern limb of the Truong Son Fold belt on the Vietnamese side of the border with Laos. These programs have produced a significant number of gold prospects at varying stages of exploration development. The Phuoc Son û Tam Ky Suture is a major Paleozoic subduction zone that extends from northern Laos, through Central Vietnam and out into the South China Sea.It represents a Lower Mesozoic collision zone between the Paleozoic-age Truong Son fold-belt terrain to the north, with the crystalline terrain of the Pre-Cambrian Kontum Block to the south. Since its formation, it has been a locus of deep faulting, continental accretion, intensive intrusive activity and mineralisation. This paper briefly discusses the geological setting, structure, metamorphism, mineralisation, exploration history, and proposed mining development of the Olympus Phuoc Son Gold Project, with particular reference to the Phuoc Son û Tam Ky suture.

Jan 1, 2004

By Thatcher R

In areas where land suitable for development is a scarce resource, an upgraded post-mining land use can result in economic benefits to both the mining company and to the community.A study undertaken at Aberdare Colliery near Ipswich during 198611987 assessed the costs and benefits of developing the site following mining for grazing, forestry and residential uses. The proposed fmal land use plan comprised a combination of these uses that can be upgraded to higher valued uses once subsidence monitoring of backfilled open-cut areas and dumps indicates that total settlement has reached acceptable levels for development to proceed.The study involved the documentation of existing site environmental parameters and the delineation of site opportunities and constraints. The unpredictable nature of settlement over backfilled open-cuts and overburden dumps represents the major constraint to urban development on mined areas.

Jan 1, 1990