Search Documents

By Tullemans FJ

This paper describes the general approach to ore reserve estimation and mine planning used at the Kidston Gold Mine. The geological setting and exploration is briefly summarized for background information.A geostatistical study of the deposit was carried out to determine the geological ore reserve. This was confirmed using a manual polygonal technique. Optimum pits outlined by a Lerchs-Grossman open pit design algorithm were manually smoothed allowing mineable reserves to be calculated. Mine production schedules based on kriged block grades and tonnages are continuously updated using production blasthole assays. An arithmetic mean technique of block grade estimation has proved successful to date. After milling approximately 4.9Mt of ore, the mill grade of 2.13g Au/t is only 0.5% above the mine estimate of 2.12g Au/t. The difference in contained gold between "As staked" blasthole reserves and kriged mineable reserves is 3.8%. The application of blasthole kriging as a basis for ore/waste classification in erratically mineralized areas is being evaluated. Planned future developments are briefly mentioned.

Jan 1, 1986

By S Moradi

The thickener overflow of zinc concentrate, obtained from flotation process in the Angouran plant located in Iran, contains a large quantity of slimes which were transferred to the tailing ponds. These slimes have caused problems of storing and environmental aspects in the Angouran area. The objective of this research is to describe the extraction of zinc from these slimes by leaching method using sulfuric acid in pilot plant scale.Chemical analyses showed that these tailing materials contain 35 per cent of zinc. By XRD analysis, smithsonite is identified as the major constituent. Calcite, dolomite, and cerussite are found as carbonate minerals. A minimal amount of Zn occurs as hemimorphite. Quartz, kaolinite, clinochlore and muscovite are other silicate minerals in the slimes.In the optimal conditions, ie acid leach at pH of 1, temperature of 55¦C, reaction time of 120 minutes and solid-liquid ratio of 1:3 and neutralisation with Ca(OH)2 at pH = 4.5, temperature = 70¦C, time = 90 minutes, the total recovery of zinc obtained was 95 per cent.

Jan 1, 2004

By Holliday RJ

The Imperial Smelting Furnace (ISF) was developed in Britain during the 1950's as a process which could produce zinc from a blast furnace. Since then it has evolved into an efficient means of producing zinc and lead from lower grade raw materials, both of primary and secondary origin. These changes have been in response to the need to improve the cost competitive position of the ISF in a climate of decreasing metal prices. The improvements at the Cockle Creek smelter of Sulphide Corporation Pty Limited have resulted from work undertaken in four main areas: 1. Changes in plant design and operating practice to give more stable furnace operation. 2. Improvements to the quality of sinter being charged to the furnace. 3. Improved monitoring of process variables and the formulation of control strategies based on the improved data. 4. Increased understanding of the processes occuring within the furnace shaft to allow predictive modelling to be undertaken. Work in these areas is still progressing but the work to date has resulted in a significant improvement in the production rate and efficiency of operation.

Jan 1, 1984

Although laterite ores already provide a significant proportion of the world's nickel and cobalt production it is anticipated that they will surpass sulphide ores as a source of nickel in the next century. The most recent period of greenfield nickel project construction was during the 1970s when it was notable that all of the eight new plants were based on treating laterite ores. This was because of the relatively large selection of available high grade laterite ore deposits amenable to cheap open cast mining and a paucity of high grade sulphide ore prospect alternatives. Of the three processing options for treating laterite ores: 1. smelting for the lower horizon saprolite ore, 2. ammonia; and 3. acid leach for the upper horizon limonite ore, smelting currently accounts for about 80 per cent of nickel production. In the future, as saprolite ore grades decline because of relatively high exploitation rates, the incentive to process the large untapped reserves of limonite ore will increase. The high cobalt content of limonite ore also makes it ideally suited to processing by a hydrometallurgical rather than smelting route. With only two exceptions, all saprolite smelting operations have a Class 2 nickel end product (largely ferronickel) and do not produce a cobalt by-product. As a result of technological advances, the modified ammonia leach process for limonite and transition ore as undertaken at Yabulu, now allows the production of pure nickel metal as a Class 1 product, along with significant tonnages of cobalt by-product. The mixed Ni-Co sulphide intermediate product of the pressure acid leach processing of limonite ore at Mon is converted to Class 1 nickel and cobalt metal at Fort Saskatchewan, Canada.

Jan 1, 1996

Mt Muro was a gold and silver mine in Central Kalimantan on the Island of Borneo, Indonesia. Aurora Gold through its Indonesian subsidiary Indo Muro Kencana owned the project. Processing commenced in November 1994, and ceased in June 2002. Mining, including prestripping, commenced in March 1994, and ceased in May 2002. Nominal throughput was 1.5 Mtpa, at average grades of 3.80 g/t Au and 99 g/t Ag. From the start of prestripping until the end of 1996, Drill Blast sampling was the main grade control method. After several studies into the viability of Reverse Circulation, including an assessment of costs and benefits, the switch from Drill Blast to Reverse Circulation was made in late-1996. From 1997 until the end of the project Reverse Circulation was the main grade control method. The mine-to-mill call factors û the reconciliation between predicted and actual tonnes and grades delivered to the mill û for the period from commencement of processing to December 1996 were 1.069 for tonnes, 0.949 for gold, and 0.969 for silver. The mine-to-mill call factors between January 1997 and June 2002 (excluding a period of significant illegal mining) are 1.086 for tonnes, 0.977 for gold and 1.025 for silver. At face value this indicates a 2.8 per cent absolute improvement for gold, and 5.6 per cent for silver. Using average grades for the project, an additional 5112 oz of gold, and 267 173 oz of silver were delivered annually to the mill using Reverse Circulation sampling instead of Drill Blast sampling. The additional recovered metal value is estimated at $US 2.87 M annually, significantly exceeding the cost of Reverse Circulation drilling. This paper discusses a number of issues that may affect the estimated benefits.

Jan 1, 2003

By Boyack DJ

DEFINING AN ECONOMIC TARGETExploration usually begins with the corporate goal of finding a minimum tonnage and grade of a selected mineral. Sometimes this is expressed more simply as a minimum quantity of contained metal without any indication of the desired grade or implied profitability. Such a goal is useful in the selection of exploration areas and the planning of initial drilling programs. However, it should be reviewed as soon as significant mineralisation has been identified. To make rational decisions about exploration expenditure, the potential return from a deposit must be estimated from the outset and re-esti-mated frequently.The potential return will depend on:1. The proportion of mineral which can be economically recovered from the deposit by mining (the mining recovery).2. The quantity of valuable constituent that can be recovered after dilution with waste rock during mining and losses due to incomplete metallurgical recovery.3. Expectations of price and markets.4. Capital and operating costs applying to the selected mining and processing methods, and to transportation and marketing. Increasingly, environmental costs and constraints must also be considered.

Jan 1, 1990

By K Buda, W Staunton, M Hill, V Tjandrawan

One of the challenges facing the gold industry in the 21st century is the continuing need to identify new reserves of economically treatable ores. Discoveries of large, metallurgically simple orebodies are becoming increasingly rarer, forcing companies to investigate options for the processing of ores which may present recovery, economic and/or environmental issues, requiring innovative approaches to their treatment. Ores which contain naturally occurring carbonaceous material (æpreg-robbing oresÆ) are an example of one such ore type. NewmontÆs Jundee operation contains zones of carbonaceous ore within the oxidised orebody. A program consisting of detailed laboratory work and extensive plant trials has been undertaken to assess the options of the processing of this material. Laboratory tests demonstrated the advantage of carbon-in-leach (CIL) over direct cyanide leaching and carbon-in-pulp (CIP) for treatment of these ores. The laboratory program identified several factors which would enhance overall gold recoveries where preg-robbing ore was being processed, including: keeping preg-robbing ore separate from non-graphitic ore; maximising gravity recovery; and ensuring the plant operates in æpureÆ CIL mode, ie no leaching prior to first adsorption tank. Several plant trials were undertaken to assess the economic sustainability of treating moderate preg-robbing ores through a modified gravity/leach/adsorption circuit. Results indicated that where good operational control of the circuit was maintained to ensure high gravity recovery, minimal leaching prior to carbon contact, and maintenance of good, active carbon inventory, then acceptable and sustainable overall gold recoveries could be obtained. Using these relatively simple plant modifications potentially allows a plant to treat ores with preg-robbing index (PRI) values up to one. When PRI values rise to 1.3 - 1.6, leach recoveries can drop from >85 per cent to

Jan 1, 2007

By P Joyce, A S. Ray, P S. Thomas, J Haggman

Climate change and global warming present a significant challenge as unsustainable levels of greenhouse gas emissions arising from human activities continue to be emitted. The cement industry is responsible for between five and ten per cent of annual world carbon dioxide emissions; most arising from the manufacture of Portland cement (PC). An effective way of reducing emissions is by incorporating supplementary cementitious materials (SCMs) as partial PC replacements. SCMs are silicate or aluminosilicate based pozzolanic materials which, in finely divided form, combine with water and calcium hydroxide (lime), liberated by cement hydration, to form compounds exhibiting cementitious properties. Pitchstone is such an aluminosilicate and has the potential to act as an effective pozzolan for partial replacement of PC. In North Queensland, Australia, a vast deposit of pitchstone is mined and processed for expandable perlite aggregate. During the classification stage of the excavated natural material, waste pitchstone fines (PF) less than 0.5 mm in size are generated. This study evaluates the waste PF as a viable, eco-friendly pozzolan for the partial replacement of PC. The reactivity of the PF is compared to fly ash (FA), using the pozzolanic compressive strength activity index (SAI) after seven, 28, and 91 days ageing at 20 per cent and 40 per cent PC substitutions. PF was found to be comparable to FA as a pozzolan at 20 per cent PC substitution at all ages tested. However, for the 40 per cent substitution blends significant strength was only achieved at 91 days ageing for the FA blend. The pozzolanic reactivity was also investigated using thermogravimetric analysis to determine the degree of free lime present after 91 days. In all cases where an SCM was added, the free lime was observed to be consumed with increasing age.

Jan 1, 2008

The GDR has extensive lignite deposits at its disposal, which formed the basis for the development of an independent energy source after 1945 and which will retain their significance well beyond the year 2000 (see fig. 1). In 1946 lignite output was about 110 x 106 t. In 1985 312x 106 t was produced and in 1988 the planned output will be ca. 315 x 106 t. Thus, the domestic produc- tion of lignite covers ca. 75% of the GDR's primary energy requirements. More than 80% of the electrical energy is gener- ated by the use of lignite and about 12% by nuclear energy. In addition to this, about 18 x 106 t/a mineral oil and about 6 x 109, m3/a natural gas are imported, predominantly from the Soviet Union. The lignite deposits of the GDR are of Tertiary origin and are recovered exclusively by opencast mining. There are two large regions (fig. 2): - in the region east of the river Elbe (Cottbus/Senftenberg- "Niederlausitz") and - in the region west of the river Elbe (Halle/Leip- zig/Magdeburg). These deposits differ in geological age and conditions of depo- sition, consequently there are differences in their chemical and physical composition and, thus, in their uses. The younger Mio- cene coals of the main region in the East of the river Elbe belong to the epirogenetic type and have a low content of ash and sul- phur. Among other things, they are suitable for the production of brown coal high-temperature coke (Lauchhammer and Schwarze Pumpe). The older Oligocene coals of the Halle/Leip- zig region are bitumenous in certain areas. Therefore, they form the basis for production in low-temperature carbonizing and chemical plants. In the Halle-Magdeburg region, where the lig- nite is in contact with the underlying Zechstein subdivision, so- called "salt coals" are found.

Jan 1, 1989

By P Waters, S Miller

BHPBilliton operates the Mt Whaleback Mine located in the semi-arid Pilbara Region of Western Australia. Approximately 200 Mt of net acid generating (NAG) material still remains to be mined. Acid Rock Drainage (ARD) was first identified at the site in 1995 following cyclonic storms. This resulted in the development of strategies that have allowed the mine to successfully manage ARD whilst continuing to operate. BHPBilliton Iron Ore is working toward prevention of ARD in its operations, however, historical practices have left residual areas that must be considered. Three significant sources of ARD have been identified that must be managed: stormwater run-off from exposed pyritic shales in pit surfaces; basal flows beneath overburden storage areas following rainfall events; and contaminated water from pit dewatering. The mine contains all ARD water onsite. This is achieved by: storage of all affected water in the ARD dam; evaporation of affected water from the ARD dam and the adjacent evaporation ponds; pumping from upstream dams to prevent stormwater from being affected; and emergency storage and treatment in-pit as a contingency. The site ARD management strategy is approved by senior management and endorsed by State Government regulatory authorities and relevant external stakeholders. Additional strategies are also under evaluation to effect long-term closure of the operation. Record rainfalls from 1998 - 2001 have tested the capabilities of the ARD strategy and management plan. Learnings from these events, coupled with recommendations from an extensive technical audit in 2000, have been incorporated into the strategy for ARD management. This paper presents the strategy and an overview of the ARD management plan that can be considered and applied by other affected sites in the management of ARD.

Jan 1, 2003

The Osborne copper-gold deposit (within the Trough Tank project area) is located in the Cloncurry Shire about 195 kilometres south-east of Mount Isa. It is hosted by Proterozoic metasediments of the Eastern succession of the Mount Isa Inlier. The deposit is overlain by 25-40 metres of Mesozoic cover, so it represents a true "blind target". Placer Exploration has 100% outright ownership of the property, having purchased the remaining 10% interest in the property from Shell in early 1993.Intensive exploration, both surface and via drilling at Osborne, has taken place since 1985, when CSR Limited Mineral Exploration and Development Group (acquired by Placer in 1988) entered into a joint venture with Billiton Minerals. Exploration effort from 1985 to June 1988 outlined a 20 kilometre strike length of magnetic horizons, in what was termed the North-East, Central and Southern anomalies, which were drilled with weak indications of copper-gold mineralization in the North-East anomaly. During the later half of 1989, four core holes were drilled into the shallower northern partofthe North-East anomalywhere previous drilling had outlined economic intersections of mineralization. These holes encountered high-grade copper-gold mineralization confirming the potential for an economic deposit to be hosted within the ironstone sequence. Further drilling involving over 400 holes (100 kilometres of drilling) has brought the deposit up to its present resource status.The current resource inventory is 36 million tonnes grading 2.0% copper and 1.0 grams pertonne gold and includes a high-grade zone of 13 million tonnes grading 3.6% copper and 1.5 grams per tonne gold. The discovery of this potential economic mineralization resulted from a persistent exploration effort based on indications that a large mineralizing system existed within a sequence of ironstones.

Jan 1, 1993

New South Wales mining legislation reinforces a systematic approach to safety management. It is now a requirement of all mines in the coal, metalliferous and quarrying sectors in NSW to prepare a Mine Safety Management Plan. The paper briefly outlines work currently being undertaken by the Safety Operations Branch of the NSW Department of Mineral Resources (DMR). The DMR is working proactively with NSW mines in the preparation and implementation of effective Mine Safety Management Plans. There is a growing realisation that a systematic approach to safety management, underpinned by the process of hazard identification, has real potential to improve safety in the workplace. The paper briefly describes the framework used in a current æmines education programÆ and its æduty of careÆ foundation. Particular attention is paid to the role of mining operators in the implementation of Mine Safety Management Plans and their expected behaviour in demonstrating compliance. One challenge is convincing some mining operators that they must adopt new ways of working. Safety Operations officers are often reminded of the need to translate Mine Safety Management Plans into practical safety systems during audits and inspections of mines and through investigations into accidents and incidents. To have a real effect on the mineÆs safety performance, using these systems must be a normal way of going about a dayÆs work for all persons who work at the mine: not a safety manual collecting dust on the mine managerÆs bookshelf. Mine Safety Management Plans are important to mining operators. Not only will positive involvement in the development and use of safety systems ensure they meet their obligations under mining legislation, but it will also help prevent themselves or their workmates being injured or killed.

Jan 1, 2002

By E Ahern

In exchange for issuing minerals rights from the Crown Mineral Estate to explorers and miners, the Crown expects a æfair returnÆ on this investment, ultimately for the benefit of all New Zealanders. In the case of mining permits, this return is in the form of a tangible asset û royalties from mining activities. But for exploration activity, the return sought by the Crown is an intangible asset û information. The information obtained serves three purposes û in helping Crown Minerals to set work programme conditions during permit allocation, for monitoring the performance of permit holders in accordance with permit conditions, and for archiving and making available for future interested explorers and other parties. Difficulties can arise during the allocation and monitoring process when either party has more information than the other that is not shared. To date not enough emphasis has been placed on the intrinsic value and content of the information generated by explorers and the importance this information can have in the exploration process leading to new mineral discoveries. For attracting exploration investment, the quality and availability of such information, combined with other geoscientific data, is a fundamental determinant for potential explorers when choosing to explore in a global market, and strongly defines the mineral prospectivity for a country. This is something the Australian States and other jurisdictions seeking mineral investment learnt long ago, and who now provide substantial amounts of cheaply or freely available packaged geoscientific datasets, increasingly over the Internet. To have a vibrant mineral exploration industry so that the benefits from the mineral estate can be realised for all New Zealanders, a shift in emphasis to the value of its mineral information base itself is required. Such an approach is befitting of a true Knowledge Economy, and would enable the Crown to make better-informed decisions regarding utilisation of its natural resources.

Jan 1, 2002

By Y A. Stepanyants, J Crawford

A practical field method for determining the maximum value of the intrinsic oxidation rate, Smax , of sulfidic materials in waste rock dumps is proposed. Knowledge of the intrinsic oxidation rate of sulfidic materials distributed in a dump is necessary for predictive modelling of oxidation and pollutant generation over time. The suggested method uses the fact that drilling waste rock dumps to install probes for monitoring temperature and oxygen concentration causes large volumes of air to be injected into a dump by the drill rig. By measuring the rate of decrease of oxygen concentration along the length of a borehole immediately after installation, it is proposed that Smax can be calculated at different depths. The aims of this work were: to derive a simple, practical formula for the estimation of Smax from the oxygen concentrations measured over time, based on some simplifying assumptions; to use a two-dimensional numerical model that incorporates all the necessary physical processes to model the behaviour of an aerated dump over time for a reasonable range of dump and material parameters; and to compare the results of the two approaches to assess the validity of the simple formula as a method for estimating Smax. It has been found that the technique can provide reliable estimates of Smax when the value is of the order of 10-7 kg(O2) m-3 s-1 or greater. At the lower end of the range however the radius of the zone aerated during drilling becomes an important parameter and further work has been recommended to investigate this aspect of the method.

Jan 1, 2003

The mining industry views with the utmost concern, legislative or administrative action that inherently reduces the scope for exploration activity. Is there any basis for this concern in relation to Victoria? This paper will outline the role of the Department of Minerals and Energy and the main features of legislative provisions affecting exploration effort. The practical difficulties that confront the Department and explorers alike will be examined. The importance of industry representation to influence the direction that policy and legislative review might take, will be highlighted. Above all, the paper will establish that one essential duty of government is to ensure the provision of appropriate mining titles and security of tenure.

Jan 1, 1982

The smaller mining company with full ownership of, or participation in, a mining project is generally unable to obtain funding as easily as the major mining house. While the equity market remains the main funding source for small projects, debt fund- ing options are becoming more available. Many international banks possess in-house mine fin- ancing expertise which can assist the smaller company in financing its share of project development. A clear understanding is necessary of both the benefits and limitations of bank funding, to ensure that all potential sources of funds are properly considered and integ- rated into the financial plans of the smaller mining companies.

Jan 1, 1984

A universal grinding circuit model suitable for an arbitrary structure of flowsheet has been suggested. In this model classifiers and mills are described in a most general form. What puts the model in a class by itself is the automatic mass balancing in all streams of the circuit. In order to provide this a special classifier model is adopted. A previously published continuous steady state process model is used as a grinding model. Non-linearity of classifier model leads to a resultant circuit model which is equivalent to a non-linear integral equation. It complicates somewhat calculation algorithm in comparison to that of linear model, but provides a physically meaningful solution.

Jan 1, 1993

In June 1996, Nord Resources Pacific (Nord) decided to work towards obtaining all necessary approvals from the government of PNG for a mine on Simberi Island in the Tabar Island Group, New Ireland Province. On the 9th of September 1996, Nord submitted a Proposal for Development and an application for a Mining Lease to mine the oxide gold deposits on Simberi Island. The Mining Lease was granted on the 3rd of December 1996 in a signing ceremony on Simberi Island. This was achieved in the extremely short time frame of less than 3 months and this paper attempts to explain the processes which made it possible.

Jan 1, 1997

The undeniable fact of life in the next 25 years will be the increasing difficulty of the physical conditions of Australian orebodies facing future miners. We are all familiar with names such as the 3000 orebody at Mt Isa, Hilton, Century, Macarthur River, Cannington, and Ernest Henry. These projects represent a significant. proportion of the planned underground mine development in Australia. Moreover, many of these new orebodies are an order of magnitude more difficult to mine and process than their predecessors. Extraction will be from deeper and potentially more hazardous working environments. Occupational health and safety considerations will place unprecedented demands upon mine operators and technology providers of the future.

Jan 1, 1994

By A Purchase, C Stacey

The procedure for operation of deluge systems installed in road tunnels is still a subject of debate. The work undertaken in this paper assists in the understanding of the effects of deluge in road tunnels, and thus aims to help inform the development of operational policy. Analysis was undertaken using computational fluid dynamics (CFD) simulations to help explore the deluge interaction with the tunnel ventilation (including smoke exhaust) and combustion products. It was found, for the scenarios considered, that: Deluge activation can decrease the required critical velocity for smoke backlayering, and this in turn can improve the effectiveness of a smoke exhaust system.The dominant parameter for deluge effectiveness is the vehicle configuration, with shielded scenarios (such as a fire in the passenger compartment) showing almost no water reaching the fire. The water delivery rate (5 mm/min versus 10 mm/min) has only a minor effect on the smoke duct damper inlet temperatures and downstream smoke temperatures for small fires (5 MW). For large fires (50 MW) the higher water delivery rate gives slightly improved performance (lower damper inlet temperatures and lower downstream smoke temperatures). A one-dimensional transient tunnel model incorporating different operational and deluge response policies (ie deluge activation times) was developed. It was used to examine the influence of different operational parameters on life safety risk and tunnel damage risk. It was found, for the scenarios considered, that: The life safety risk for different scenarios has a sensitivity to deluge activation policy with the case of delaying the deluge activation for a long time giving the worst outcomes. However, the most critical parameters for life safety risk are operator response time (for all response activities, not just deluge) and the type of fire (configuration, size and growth rate).There is a reduction in risk of tunnel damage when the deluge is activated earlier, although the fire configuration (ie whether or not the seat of the fire can be reached) has the greatest influence on the outcome. It is concluded that the deluge activation policy should be case-dependent. It will depend on the tunnel, the safety systems provided, and most particularly the vehicles involved. The current policy in Australian tunnels is for manual activation of the deluge by the tunnel operator as soon as practical after the fire is confirmed (see also PIARC, 2007). This is a good policy. However, future work may be helpful to improve the skills of operators to make the best judgement as to when deluge should be activated, balancing all risks. This work could include research to further the understanding of deluge and fire in road tunnels, training programs and consideration of historical fire events.

Jan 1, 2008