Search Documents

The introduction of cement into underground backfilling at The Zinc Corporation, Limited and New Broken Hill Consolidated Limited mines to improve mining efficiencies gave rise to several major problems, the magnitude of which had not been anticipated. These problems were 1. A loss of recovery in the milling circuit due to the presence of cement 2. The presence of cement-rich slime layers on the surface of the fills 3. The introduction of a safety hazard due to the slippery nature of the surface of cemented fills 4. The deposition of cemented slimes on the levels and in underground sumps and dams. The loss of revenue due to decreased metal recoveries considerably offset the gains from increased stoping efficiencies and the use of cement was substantially reduced while, (a) the Metallurgical. Department attempted to identify the chemical nature of the problem and overcome it, and (b) the Mining Department investigated methods of reducing cement contamination of the ore stream. As a part of this investigation the Mining Department added polymeric flocculants to the cemented fill pulp. Testwork was carried out in the following steps 1. The available Alfloc polymers were screened to determine which was the most effective and what was its optimum dosage rate. 2. This polymer was used in the laboratory to determine the reduction of surface slime, clarity of water, and effects on strength and percolation of fill. 3. Fills were placed underground to substan- tiate the laboratory work. /+. The polymer was then added to all cemented fills going underground to study its effect over a long term. The use of flocculants not only improved the distribution of cement in the body of the fill, but also the distribution of the fines fraction of the filling material, practically eliminated slippery surfaces and improved the clarity of the drainage water. Flocculant is now added to all cemented fills and restrictions on the use of cement are gradually being lifted.

Jan 1, 1973

By B Wiggins, M Russell

Off-gas handling systems are a critical component of modern metallurgical furnaces and typically represent as much as 50 per cent of the total installed smelter capital cost. Inadequate off-gas system performance, due to insufficient exhaust flow or excess maintenance downtime, can present a serious process bottleneck and limit smelter production rate. Therefore, it is essential that the relevant performance issues are fully understood and considered in the design of these systems, particularly when combustibles produced within the furnace must be combusted or handled in the off-gas system. This paper examines the requirements, design issues, and conceptual design process for state-of-the-art postcombustion off-gas systems. The relevant design considerations of safety, environment, energy consumption, and maintenance are presented, and the relative importance of these key issues are compared and discussed. The benefits of using computational fluid dynamic (CFD) modeling in the design process at the conceptual design stage are also demonstrated. Finally, the design basis and performance of a recent Hatch-engineered system currently in operation is evaluated.

Jan 1, 2002

When, in 1985, Marty McFly is accidentally sent back to 1955 in a DeLorean ‘time machine’ in Back to the Future, he encounters young versions of his parents, and must make sure they fall in love or he will cease to exist. This Conference celebrates 40 years since the inaugural Mill Operators’ Conference in Mt Isa in 1978; over this period, great technological advances have been made in almost all aspects of mill operation, resulting in considerable improvements in grades and recoveries from ever-more complex ores. However, in 2018, the mining industry is facing challenges that might have been difficult to predict in 1978 (or were they?). The computer revolution, the information revolution, and the bio-technology revolution have all contributed to the increase in operating efficiencies, but, combined with the social revolution, they also call into question the existence of the mining industry as we know it. This presentation looks back at the ‘way things were’ in the 1970s, and at what was then considered to be the ‘basics,’ and attempts to sketch what the mining industry might be like in 2058. As Back to the Future Part II demonstrates so vividly, it is much easier to review the past than predict the future. It is difficult to know what form the mining industry will have in 40 years’ time. Nevertheless, as this presentation will argue, it is important to take action now, to ensure that it (like Marty McFly) does not cease to exist. Some courses of action are proposed, including going back to the basics of a very different past.*This is an abstract only. No full paper was prepared for this abstract.*CITATION:Franzidis, J P, 2018. Back to basics or back to the future?, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 3–4 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By L B. Zhou, Q Wang

The present discussion focuses on the developmental directions of eco-restoration of acid mine waste rock dump, by using acid mine waste rock of Shuilong Mountain as an example. Based on the analysis of site factors, the current slope ecological restoration technologies of domestic and international and local practices have been integrated into the eco-restoration of acid mine waste rock in Shuilong Mountain. A set of suitable slope Eco-restoration technologies have been formulated locally for acid mine waste rock of Shuilong Mountain, which include establishing green barrier, implementing ecology buffer zones, selecting suitable plant species and combined seeding and tube-stock planting. It aims to restore the plant ecosystem to a near natural state, in couple with slope stabilisation and soil remediation.CITATION :Wang, Q and Zhou, L B, 2012. Projection of ecological restoration of acid mine waste rock of Shuilong Mountain at Dexing Copper Mine, in Proceedings Life-of-Mine 2012 , pp 305-308 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 10, 2012

By G McCullough, B Mutsaers, J Jessop

"*This is an abstract only* Geometallurgical initiatives have demonstrated considerable value to operations that have trialled them. However, it is extremely difficult for these initiatives to become properly embedded into the operations and for that value to be realised on an ongoing basis.This paper will explore some of the historical reasons why this is the case. Some of these reasons include the limited tools available to manage an integrated operation. These, in turn, have resulted from poor communications infrastructure, inadequate sensor capability and the way technical mining software has evolved over the last 30 years.This paper will then investigate how the evolution of technology in recent years can help overcome these constraints and compare progress with similar industries.CITATION:McCullough, G, Mutsaers, B and Jessop, J, 2013. Obstacles to embedding geometallurgy decision-making into operations and how to increase maturity of this critical capability, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013, pp 139-140 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Sep 29, 2013

By P Duuring

Late-Archean banded iron formation (BIF)-hosted deposits in the Yilgarn Craton of Western Australia are less well understood compared to the larger Paleoproterozoic, Superior-type BIFhosted deposits of the Hamersley Province. The Weld Range greenstone belt, in the Murchison Domain of the Yilgarn Craton, hosts two Archean, high-grade deposits, Madoonga (68 Mt resource at 57.7 wt per cent Fe) and Beebyn (62 Mt resource at 59.6 wt per cent Fe, ASX announcement 2008). Five main types of high-grade (>55 wt per cent Fe) iron mineralisation at Weld Range each display characteristic grades, tonnage, and contaminant levels, which affect exploration strategies and beneficiation methods:1. ‘Residual’ ore formed as a result of two generations of hypogene alteration of BIF. The first alteration phase replaced silica-rich bands with siderite and/or Fe-rich dolomite; the second phase involved the removal of carbonate gangue minerals and the concentration of residual Fe oxide-rich bands in the BIF via volume reduction. The product is a high-grade, high-tonnage Fe orebody, with minor contaminants.2. Magnetite-bearing shear and fault zones cut BIF along lithological contacts. These zones of secondary magnetite formed as a result of the addition of hypogene magnetite via the circulation of Fe-rich, hypogene hydrothermal fluids through BIF. This type of mineralisation produces narrow (low-tonnage), high-grade magnetite-rich ore zones with high levels of contaminants (eg SiO2, Al2O3) due to the difficulty in mining these zones.3. Specular haematite ± quartz-bearing shear and fault zones cut residual orebodies and magnetite bearing structures. They share similar characteristics to magnetite-bearing structures.4. Goethite-haematite supergene ore zones are controlled by brittle faults that cut BIF. These faults promoted the flow of supergene fluids through BIF and resulted in large ore zones with variable Fe grades and contaminants.5. Detrital deposits comprise transported BIF fragments and are intensely goethite-haematite supergene-altered. These orebodies are locally extensive, with moderate Fe grades.

Jul 11, 2011

Continuous improvement in environmental management assists in the achievement of sustainability goals for the processing of minerals. The use of regular internal environmental audits (scored or unscored) which form an integral component of an Environmental Management System (EMS), provide demonstrable evidence of this improvement. Case studies are presented for a number of major coal mines in the Hunter Valley, where regular internal environmental audits have been undertaken every two to three months, over periods varying from 18 months to five years. Examples of the benefits of improved environmental performance (driven by the audit process) to sustainable development are provided.The auditing process as described here for coal mines, and coal handling and preparation plants, is equally applicable to the processing of other mineral ores, metalliferous mines, quarries, and oil and gas projects.

Jan 1, 2004

By R Grogan

Nautilus Minerals Inc is a sea floor resource exploration and development company focused on developing the Solwara 1 Project, a copper-gold sea floor massive sulfide deposit in the territorial waters of Papua New Guinea, for which it holds a mining lease and associated environment permit.Economies depend upon four key types of capital: built, natural, financial and human. Natural capital consists of the ‘minerals, energy, plants, animals, ecosystems (climatic processes, nutrient cycles and other natural structures and systems) found on Earth that provide a flow of natural goods and services’ (Daly and Farley, 2004). Many ecosystem goods such as fish, fruit and water are already valued and sold in markets; however, some ecosystem services are not amenable to markets and have remained unvalued in traditional accounting methods, even though they provide significant value (such as flood protection, climate stability etc; Batker and Schmidt, 2015).There are now economic methods available to quantify and value natural capital and many non-market ecosystem services. When valued in dollars, these services can be incorporated into a number of economic tools, including benefit-cost analysis, accounting, environmental impact statements, asset management plans and rate of return on investment calculations. Their inclusion ultimately strengthens decision-making. When natural capital assets and ecosystem services are not considered in economic analysis, they are effectively valued at zero. This omission can lead to poor decisions, inefficient capital investments, higher incurred costs and losses due to unexpected events (Batker and Schmidt, 2015).In 2015 Earth Economics was commissioned by Nautilus Minerals Inc to conduct an independent, objective environmental and social benchmarking analysis of the proposed deep seabed Solwara 1 mine with terrestrial copper mines (referred to as ‘the report’). The report represents the first ever natural capital accounting and ecosystem goods and services framework for seabed mining.The report compares the proposed Solwara 1 mine with three terrestrial mines: Bingham Canyon (Utah, USA), Prominent Hill (South Australia, Australia), and Intag (a proposed mine in Intag Province, Ecuador), and provides a natural capital accounting assessment for all four operations.CITATION:Grogan, R, 2016. Natural capital accounting – a sea floor mining application, in Proceedings Life-of-Mine 2016 Conference, pp 2–4 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jun 28, 2016

By D Bradshaw, E Forbes, M Edraki, M Tayebi-Khorami, E Manlapig

There is an increasing trend in the extraction and development of copper resources from complex deposits. These deposits pose mineral processing challenges, as they often contain low grade disseminated copper ore with high levels of impurities particularly arsenic. Although arsenic is a naturally occurring element, the concentrations of arsenic can be magnified by mining and mineral processing activities. Therefore, while arsenic has no significant market value, its presence in the ore deposit will have production, environmental and human health implications. The mining industry’s approach to life-of-mine planning has improved significantly in recent decades and managing arsenic is not an exception.CITATION:Tayebi-Khorami, M, Edraki, M, Manlapig, E, Forbes, E and Bradshaw, D, 2018. Arsenic pathways in copper mining – sustainability issues and potential solutions, in Proceedings Life-of-Mine 2018, pp 60–63 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

By K M. Cook, D Clark

Fatality prevention and zero harm are key focus areas for resource companies. However, they remain an ongoing challenge for high hazard industries, including the mining sector. As one example the latest International Council on Mining and Metals (ICMM) Safety Performance Report shows that, while there is generally a declining fatality trend since the organisation commenced publishing data in 2012, there were still 33 fatalities across member companies in 2022 (ICMM, 2023b). Every fatal incident brings significant pain and suffering to the colleagues, friends and family of those involved, however the failures and causal factors leading to each incident are frequently very familiar to people working in the industry, particularly those tasked with managing risk and safety. In the words of Dame Judith Hackitt, Grenfell Tower Fire Investigator, ‘there are no new accidents – just different people making the same mistakes because they haven’t learned’ (Hackitt, 2022). The recurring themes in terms of the nature of fatal hazards and their associated causes across the mining sector show that, despite improvements evidenced by the favourable declining fatality trends over the long-term (in general and outside of catastrophic multiple fatality events), changes are required to achieve fatality elimination and the aspiration of zero harm. This extended abstract and the accompanying presentation apply a mining frame of reference to the idea that there are no new accidents, examining how this applies within the industry and why the lessons from past failures are not always well understood or applied to prevent the reoccurrence of material unwanted events. Many contemporary mining and resources organisations have extensive internal incident history data and a wide variety of information on fatality incidents is publicly available, including the annual ICMM Safety Performance Report. This extended abstract and the accompanying presentation explore how this existing data can be used effectively to learn from the past and proposes practical ideas regarding strategies for successful knowledge transfer to the workforce as a key component of preventing history repeating and improving safety performance across the industry. As noted by ICMM, ‘sharing lessons from failure is vital to improving health and safety, but it’s not enough’ (ICMM, 2023a).

Apr 16, 2024

By S A. Prevec

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. Traditional models employed to genetically link associated chromite and platinum-group elements have favoured crustal contamination as the primary process for inducing sulfide and oxide saturation. The association of chromite ores with crustal contamination is well established in the literature. However, in the 1970s (cf Irvine, 1973, 1975), Irvine demonstrated that crustal contamination was in fact problematic as a tool for inducing chromite precipitation in mafic to ultramafic magmas. His results are re-examined here, along with some attempts to reconcile them with the effects of adding Fe to the models. It is concluded that crustal contamination is indeed problematic based on phase relationships alone. However, the role of fluids as a compensating agent is evaluated, which may explain why crustal contamination may indeed facilitate oxide and sulfide precipitation.CITATION:Prevec, S A, 2015. Chromite and platinum-group elements coprecipitation by crustal contamination or magma mixing revisited – genetic and exploration implications, in Proceedings PACRIM 2015 Congress, pp 311–316 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

DuPont is a chemical and energy multi-national of approximately 90,000 employees. Often regarded as the world leader in injury reduction and process safety management, DuPont operate 140 manufacturing sites around the globe. Conoco is a wholly owed subsidiary of DuPont which is involved in oil, gas and coal exploration.   Throughout this paper I will discuss DuPont statistics, developing a safety culture and training process as well as discussing possible short comings in the New Zealand safety focus. I will conclude with my recommended improvements and issues for New Zealand companies to focus on.   It is very difficult to compare DuPont and New Zealand statistics through lack of compatibility in recording methods and my ability to interpret ACC's Injury Statistics. However through considering DuPont's statistics, and comparing them to your own companies or departments, you will agree they are indeed impressive. I hope that by discussing DuPont's safety philosophy, and possible shortfalls within New Zealand Legislation many of you will find ideas and inspiration which will help you to further reduce your own injury rates.

Jan 1, 1997

By Travis G. A

The Mons Cupri Cu-Pb-Zn deposit is situated within a complex Archaean volcanic sequence dominated by rhyolitic fragmental rocks. This sequence is underlain by a 150 m group of rhyolitic ash flow tuffs with minor conglomerate and sandstone, and is overlain by approximately 180 m of dacite and andesite flows. The Mons Cupri sequence itself consists of several elongate or circular rhyolite domes, flanked by rhyolitic fragmental rocks ranging up to 400 m in thickness away from the domes. The lithology of clasts (typically 1 cm to 1.5 m in size) provides strong evidence that the flanking fragmental unit was derived by explosive eruptions associated with the rhyolite domes. An approximately 15 m thick shale horizon, bleached and silicified at its base, overlies both the rhyolite domes and the frag- mental unit. A south-dipping chloritic pipe-like body, with near-surface dimensions of 1,000 by 250 m and narrowing at depth to produce a cone-shaped cross section, lies within the rhyolitic frag- mental rocks about 250 m north of the largest rhyolite'dome in the Mons Cupri vicinity. Its east west elongation parallels that of the rhyolite dome. Ghost fragments indicate that the material in this fissure is a severely chloritized derivative of the rhyolitic frag- mental unit. The chloritic pipe is overlain

Jan 1, 1973

By H Zhang, Y Wang, S Sukenaga, H W. Ni, H Shibata, W Z. Mu

The crystallisation behaviour of low melting point CaO-SiO2-Al2O3-MgO inclusions greatly affect the deformability of inclusions during the rolling process. The crystallisation characteristics of CaO-SiO2- Al2O3-MgO melts representing the oxide inclusions in Si-Mn killed steel were systematically investigated. The effect of Al2O3 and MgO contents on the crystallisation change were analysed under a fixed CaO/SiO2 in the complex inclusions. The continuous-cooling-transformation (CCT) and time-temperature-transformation (TTT) experiments were conducted. The results showed that the increase of MgO content increases the crystallisation ability of CaO-SiO2-Al2O3-MgO inclusions, while the increase of Al2O3 content has the opposite effect. The viscosity, liquidus temperature of oxide melt and also the initial crystallisation potential might be the reasons for the change in crystallisation behaviour. Also, the crystallisation activation energy could semi-quantitatively characterise the crystal growth during the crystallisation of inclusions. To obtain low melting point plasticized CaO-SiO2-Al2O3-MgO (CaO/SiO2=1) system inclusions, the Al2O3 content of the system needs to be controlled larger than 15 wt per cent and the MgO content should be kept at a small amount.

Aug 21, 2024

By Fredley D. C

Georgius Agricola wrote in De Re Metallica in 1556 that a prudent a miner should not work in a region ruled by a tyrant-a person inimical to mining. In 1926, Associate Chief Sherman of the United States Forest Service in a speech stated, "It is the policy of the Forest Service to encourage the development of the mineral resources within the boundaries of the National Forests ... a man who fails to cultivate a friendly, helpful, cooperative spirit in his relations with those who are endeavoring to develop the mineral wealth of our mountains has no place in the Forest Service." Both statements are as true today as they were in 1556 and 1926. The challenge to the Forest Service and the mineral industry today is to maintain that cooperation in a world that has changed significantly since Agricola and Sherman. The United States Forest Service manages 77,000,000 hectares of land-mostly in the Western United States-an area equal in size to New South Wales. The vast majority-75 million hectares are National Forests, and 1.6 million hectares are National Grasslands. National Wilderness Areas account for 13 million hectares or rough- ly 17 per cent of the National Forest System. National Forest System lands (NFS) are some of the most visible, scenic and controversial lands in the country. They are also some of the most valuable for their mineral potential and production. The value of mineral produced exceeds US$4 billion per year. There are over 1200 producing mines, 15,000 oil and gas leases, and some of the largest lead, copper, silver, gold, platinum, molyb- denum, and coal deposits in the hemisphere. Every year the Forest Service approves nearly 5,000 mineral operations on the NFS. Much of the NFS (75 per cent) is open to location of mining claims pursuant to the 1872 Mining Law. And an equal amount of land is legally available for oil and gas leasing.

Jan 1, 1991

By A Yame, P J. Pollard, E Atase, J Garu, M Tangwari, D R. Hastings, R W. Smillie

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Townsville prospect is situated approximately 4 km north of the Ok Tedi copper-gold mine in Western Province, Papua New Guinea. Drilling in the 1990s delineated a resource of >1 Moz of gold within shallow, skarn breccia-hosted mineralisation associated with quartz-carbonate infill, together with pyrite, chalcopyrite, pyrrhotite, sphalerite, galena, tennantite-tetrahedrite, arsenopyrite, marcasite, and a variety of Au-, Ag- and Bi-telluride minerals. The deepest of these historical holes (TVL034) also intersected copper-gold-silver mineralisation more than 100 m below the gold-rich zone that is associated with calc-silicate skarn breccia. Although copper-gold-silver mineralisation in DDHTVL034 is associated with clinopyroxene-rich skarn, it was also noted that garnet in the skarn breccia became progressively darker in colour with depth, ranging from green at shallow levels to dark red-brown at depth. This indicated that the skarn breccia is zoned, with more proximal garnet skarn at depth possibly indicating an association with porphyry-style copper-gold mineralisation.Based on this skarn zonation model, recent drilling at the Titan prospect, located approximately 500 m south of TVL034, was targeted at potential copper-gold silver mineralisation beneath shallow skarn breccia-hosted gold mineralisation. DDHTVL 081 intersected 46 m at 6.36 g/t Au from 68 m and 80.7 m and 1.67 per cent Cu, 1.27 g/t Au and 20.32 g/t Ag from 184 m. Exploration is now attempting to define the extent of copper-gold-silver mineralisation by defining structural controls on the skarn breccia together with paragenetic and mineral zoning data.CITATION:Smillie, R W, Pollard, P J, Hastings, D R, Yame, A, Tangwari, M, Garu, J and Atase, E, 2015. Exploration of the Townsville Cu-Au-Ag skarn, western province, Papua New Guinea – preliminary observations of paragenesis and zoning, in Proceedings PACRIM 2015 Congress, pp 593–600 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015

By M A. Noppé

"Mining is an inherently risky business: from the technical, environmental, social and economic uncertainties associated with advancing an exploration concept to a viable project; to the risks associated with the operating, market, and safety risks and uncertainties attached to a developed mine; and the final mine closure process.Investors and other stakeholders assessing the risk, opportunity and relative value associated with a resource project need to appreciate the project in its correct context. Errors, omissions, biased reporting or conflicting information in reporting may result in a misinterpretation of technical and financial results, leading to biased estimates or assumptions on project value (Noppé, 2016).Simplistically, a project can be assessed on three key areas for positioning the project in its correct relative context, namely: the project development stage the confidence in the estimated quantities and qualities of the resource, reserve and/or product the level of accuracy, precision and confidence in the technical and economic studies supporting the project.In the latter case, the ‘technical and economic’ information includes assessing the necessary social, environmental and commercial/legal/governmental approvals for the project.Responsible management of a resource project through its full life cycle relies on competent and dependable control and direction being effectively provided by the technical, business and board leadership of the organisation. In turn, the project information must be effectively communicated between various disciplines, these disciplines and the company, and the company and its stakeholders.CITATION:Noppé, M A, 2016. Responsible management and transparent reporting across the project life cycle, in Proceedings Life-of-Mine 2016 Conference, pp 5–7 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 28, 2016

By Gillies A. D S, Lee A. H

The major operational objectives of a mine water resource management system (WRMS) are to supply the water needs of the mine and mill, to minimise disturbance to mining due to rainfall flooding or seepage and to dispose of excess water. Historically, company management have placed a significantly lower emphasis on managing the WRMS as compared to managing production. Changing Government legislation concerned with the disposal of water from mine sites is, in many cases making mining companies look more closely at how they manage their water. For example, within the next few years it is likely that prior to mining approval by the Government, mining operations will have to submit water management plans/budgets and contingency strategies in addition to operational plans. While the formulation of a comprehensive water management plan/budget is an additional cost to the company at the mine establishment stage, such plans can be beneficial to the operation in the longer term.The two keys for the efficient design, operation and development of a WRMS are the establishment of written goals which have managerial priority and secondly, access to appropriate good quality data. Managerial priority towards the WRMS will increase as a consequence of the education of mine operators in the benefits to the operation of good WRMS management or less desirably as a requirement to meet Government legislation. The collection of appropriate WRMS data is a more complex issue and to obtain information efficiently and cost effectively relies on the clear definition of the data application.

Jan 1, 1992

By Aguirre E, Chitombo G

The magnitude of stress variations associated with a blast wave near production pillars is analysed by modelling blast vibrations measured in the surrounding rockmass. The results indicate a wide variation in stress which is thought to contribute to the observed damage in pillars adjacent to the draw points.

Jan 1, 1995

In the search for significant new economic base-metal resources within Australia during the early 1970s BHP's Exploration Department had observed that the majority of lead and zinc con- centrate production in Europe and the USA came from carbonate- hosted Mississippi-Valley-type (MVT) zinc-lead deposits, but Aus- tralia had no history of production from this class of deposit despite several very favourable geological environments, par- ticularly in the large Palaeozoic sedimentary basins. An exploration-research team was established in 1975 and the Lennard Shelf region, near Fitzroy Crossing, was selected as a most promising geological environment. Previous exploration for this class of deposit by other companies in Australia had largely used conventional exploration philosophies (geological mapping, geophysics and geochemistry to identify specific drill targets) but BHP sought specialist advice from a North American expert and adopted a grid-drilling philosophy, which involved wide spaced relatively deep diamond drill holes on a regular grid pattern, and statistical evaluation of the results. This technique resulted in the discovery of the Blendevale Deposit in 1978 in an area which had previously been explored by other companies using conventional methodologies. The deposit was delineated and a pre-feasibility study carried out in 1985 indicated that the resource of 20 Mt @ 8.3% Zn, 2.5% Pb was a marginal proposition.

Jan 1, 1988