Search Documents

Lower Silesia Coal Basin/SW Poland/ is adjacent to highly gas saturated igneous massiv and since the beginning of this century more than 1500 outbursts have occurred in four existing mines, including 1295 in the most hazardous mine Nowa Ruda. Prevailing part of these are carbon dioxide/coal outbursts of ejected masses 50-5000 tonnes/av.200/t and gas volume released from 200 m3 to 800,000 m3 Magnitude of these phenomena is growing with the depth and for present extraction levels/ 375-753 m/ may be expressed by a formula: M = 4.25/H-400/, where M-masses ejected, t and H - depth of extraction, m. Regulations obligatory hitherto call for gas pressure measurements to be made in 3 m long and 42 mm dia. boreholes spaces not more than 25 m along the longwall face and taking sample of drillings for desorption testing. Criteria of a hazard are following: pressure higher than 30 kPa /for C02/ or 80 kPa /for CH4/ and desorption more than 1,44 cm3/g. These criteria are not satisfactory because many outbursts occurred in spite of low values of parameters measured and for several times no hazard was evident after very high values were obtained. Moreover, observations show that a huge majority of case outbursts occurred in coal weakened by local geological distortion.

Jan 1, 1980

The areas of impact when employing high productivity long wall systems are reviewed and the financial implications of the most significant areas highlighted. A distinction has been made between availability and utilization. The need for more efficient delay recording, together with increasing control and utilization of the systems has been identified and the measurability of the latter discussed. The increased use of electronic delay reporting direct from the operating unit as the basis for operational control and a pre-emptive maintenance philosophy is seen as an important area of achieving higher performances from existing long wall production systems and Configurations.

Jan 1, 1988

To counter depressed world nickel prices, a continuing effort is being made at Kalgoorlie Nickel Smelter to reduce unit production costs. One major area in which production costs can be reduced is the substitution of coal for fuel oil. Two areas where this has been achieved to bring about a saving are, the addition of coal to flash furnace flux to reduce supplementary fuel oil requirements in flash smelting and the replacement of two oil-fired air preheaters with a coal-fired unit. These actions have resulted in coal replacing 67% of the current fuel oil requirement in flash smelting at the Kalgoorlie .Lckel Smelter.

Jan 1, 1987

Nickel-iron sulphide mineralization at Nepean, Western Australia occurs within a small Archaean greenstone outlier in granite south of the main Coolgardie greenstone belt. Individual sulphide ore bodies are situated near the foot- wall contact of simply-differentiated en echelon ultramafic sills that have intruded a sequence of sulphide-bearing metasediments and amphibo- lites. The paper describes a detailed section through the No. 2 ultramafic sill and its associated sulphide ore zone, which gave Metals Exploration N.L. the first significant nickel discovery in the Nepean area in 1968. The sill is variable in thickness up to 30 m along a strike length of 600 m, and is truncated to the north by pegmatite intrusion and pinches out to the south. The body has border zones of pyroxenetic composition, now represented by felted aggregates of chlorite and amphibole, and a central peridotitic core in which olivine and orthopyroxene are concentrated towards the base. Textures within the peridotite are dominated by large lath-shaped olivine grains and their serpentine pseudomorphs, which delineate triangular areas composed of talc, chlorite, and amphibole. Orthopyroxene occurs in large ovoid patches and is often replaced by Talc.

Jan 1, 1973

For the purposes of this paper the Newcastle Coalfield is considered to be that 35 km wide rectangular tract of country west of a line running 45 km along the coast, south from Newcastle.

Jan 1, 1993

By Aylmore M. G

Samples have been taken from a two-stage industrial gold roaster treating a pyrite/pyrrhotite/arsenopyrite concentrate, in order to describe the mineralogy, composition and surface area of the calcines. Sulphides oxidised to produce a porous magnetite in the first stage and a porous hematite in the second; pyrite predominantly roasted via a pyrrhotite intermediate. Sulphur was eliminated in both the first and second stages whereas arsenic was eliminated in the first but retained in the second, partly as rims on hematite particles. The finer sized particles from the cyclones and electrostatic precipitator, while having the greatest surface area, were the most refractory with respect to gold solubilisation, probably as a result of incomplete decomposition (through short-circuiting) in the first stage, and through a combination of factors such as overheating and entrapment of sub-microscopic gold in the second stage.

Jan 1, 1992

By D J. Williams, E M. Rykaart

Soil cover systems are routinely used to reduce acid rock drainage (ARD) from mine waste rock dumps and tailings impoundments. A technology for the analysis, design, instrumentation and monitoring of barrier-type (oxygen limiting) and store/release-type covers has rapidly developed and the number of covers under construction has grown extensively during the past ten years. Mine operators are currently investing in this relatively new technology with the expectation that these covers will reduce long-term liability with respect to acid generation, drainage and treatment costs. While the design life for cover systems may extend into hundreds of years, we have less than ten years of construction experience and proven performance. Some cover designs appear to be functioning well; however, the performance of many more is now being called into question. The paper presented herein evaluates the integrity of cover systems from a global perspective. Soil cover systems for the control of ARD are being constructed at mine sites located within high rainfall equatorial regions, deserts ranging from low to high latitude, humid temperate regions, and cold-continental climates. While the technology for analysis and design of soil cover systems is well developed, factors that compromise the performance of cover systems (in addition to the paramount issue of climate) relate to material selection and availability, cost and construction practices. Long-term performance is also strongly affected by physical stability (ie erosion), volume change (ie cracking, desiccation, settlement and freeze/thaw cycling), vegetation, soil evolution and ecological stability. This paper provides a review of the application of soil cover systems for the control of ARD. Cases where cover systems have been constructed with both success and failure are illustrated. General criteria and recommendations for cover selection, design, construction, and maintenance are provided.

Jan 1, 2003

By Fuller P. G

The purpose and current practice of cable trusses in underground coal mines is briefly outlined and details of various cable truss designs are presented. The main part of the paper describes the in-situ performance of cable trusses installed as secondary supports in gateroads and recovery roads of longwall coalfaces. The performance analysis is based on the results of in-situ monitoring carried out at a number of sites at two underground coal mines within Australia. Truss performance has been assessed as load developed in relation to roof convergence, face position and time. Additionally, the influence of strata conditions, installation pattern/density, roadway layout and geometry have been taken into account. An analytical model has been developed to predict truss loads. The principal variables are listed and the basis of the model is described. Based upon behaviour observed in the field the model has been progressively upgraded and validated against measured performance. Guidelines on truss performance and factors which influence it are presented and the implications of these to the use of cable trusses is discussed. Possible methods for improving truss performance in certain strata conditions are outlined and some comments are made on the value of cable trussing compared to cable bolting in these Situations.

Jan 1, 1992

By Jackson D. G

Iron ore mineralisation in the Paraburdoo environs is known to extend almost continuously over a strike length of 55 kilometres. Six formations of the Mount Bruce Supergroup con- tain high grade mineralisation in varying degrees of importance. Ore is currently being mined from the Joffre and Dales Gorge Members of the Brockman Iron Formation, with smaller, less significant amounts, occasionally taken from the lowermost units of the Weeli Wolli Formation and the upper parts of the Mount McRae Shale. Regional mapping has demonstrated the existance locally of a major unconformity at the base of the Wyloo Group sediments out- cropping south of the minesite. The basal con- glomerates at the unconformity are sometimes mineralised at Paraburdoo. A supergene enrich- ment process controlled by structure, strati- graphy and topography is the only one which can satisfactorily explain the disposition and chemistry of the Paraburdoo iron orebodies.

Jan 1, 1979

By B Dold

"Mining has still today high potential for improvement in the exploitation efficiency. Especially low-grade ores have very low recoveries. In Cu bioleaching operations from porphyry copper deposits extraction of only five and 15 per cent with maximum of 40 per cent are reached. This means that 60–95 per cent of the resource is not exploited. Consequently, any metal not extracted will end up in the waste material, therefore increasing the risk of environmental pollution. This inefficiency is mainly due to the use of element concentrations for decision-making on the daily basis of a mining operation (eg cut-off ore grade, acid-base accounting – ABA). If, instead, quantitative mineralogical and geochemical data together with information on the bioleaching behaviour of the ore assemblage (the biogeometallurgical approach), is used for decision-making right from the beginning of the exploitation, higher recoveries and less environmental impact can be achieved, ie an increase in sustainability can be reached.CITATION:Dold, D, 2016. The Biogeometallurgical Approach – the Information We Need to Increase the Sustainability of Mining, in Proceedings The Third AusIMM International Geometallurgy Conference (GeoMet) 2016, pp 169–172 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 15, 2016

Instantaneous outbursts have occurred at Metropolitan Colliery from the pick and shovel work of early days to the modern mining techniques of today. Developments have been the introduction of an emission index to measure the proneness of the coal to outbursts, drainage and destressing by large diameter holes, attempts at higher productivity by the introduction of pulsed infusion shotfiring and improvements in ventilation. The future plans and aims for the Colliery include prediction of outbursts, seam gas pre- drainage and longwall mining.

Jan 1, 1980

By M Sparrow

The Victoria Park Tunnel project is an inner-city alliance project in central Auckland, New Zealand. The existing two-directional viaduct will be modified to single-direction flow, and a new northbound 440 m cut and cover tunnel will be constructed beneath Victoria Park. Three-dimensional (3D) visualisation media were used to communicate key design innovations to stakeholders and the general public. The 3D visual material has proven a useful tool for informing motorists of a new safety barrier method adopted for traffic management.This presentation will explain how 3D visualisation was incorporated in the project and will showcase the 3D visualisation media created for the project.

Mar 8, 2011

By Vidalinc, Raffoux

Longwall faces producing in the order of 20,000 tons per day of raw coal are presently running in the Houilleres du Bassin de Lorraine of Charbonnages de France. Production levels of twice that level pose some technical and economic problems of coal cutting, ventilation, coal and equipment transportation in the.face and from the face to the sur- face. The peak productions of the equipment in use today, the results of trials with new equipment, the utili- sation of forecasting models (some in the form of software), allow us to fo- resee feasable technical solutions to these problems. They will first be considered in the best possible context (thick- ness, dip, non gassy, soft coal, good strata, no faults). This will give. the necessary conditions to reach daily output'of that level. A sensitivity analysis of these- figures to the effective natural con- ditions will then be undertaken and the implication of such a project on health and safety (dust, climate ...) will be carefully considered. A concise technical and econo- mical approach will permit us to fore- cast the economical interferences of such production units and specially the consequences of sudden variations of the output (downtimes, failures, etc). From this investigation, goals for technological development and re- search areas will be outlined to be able to reach this production target in the XXIst century.

Jan 1, 1988

This paper cites selected, prominent examples of current, major projects in Southern Africa in both the mining and civil fields. Differences and similarities in the life cycle of mining and civil projects are discussed. A closer relationship between the mining and civil fraternities is beginning to develop and should be encouraged because of the resultant exchange of experience and technology which benefits both disciplines. An attempt is made to assess future potential for new, major projects and trends in the implementation thereof.

Jan 1, 1999

Cable bolts have been used extensively in the development of the footwall of the Mt Whaleback Mine as a part of the ground improvement program since 1986. High tensile seven wire stress relieved steel strand similar to that used in pre-stressed concrete and grouted in place with sulphate resistant cement have been employed for rock-mass reinforcement.Most of the footwall is developed in Mt McRae Shale which contains a 20 m thick pyritic shale layer 14 m below the ore/waste contact. Due to extensive folding of the footwall rocks, the pyritic shale layer regularly occurs on, or close to the pit slope. Rain water run-off seeping through pyritic shale becomes acidic to the extent where its pH value can be as low as 1.5.

Jan 1, 1992

This paper outlines the aims, objectives and means by which a life of mine land use plan was established for Comalco's bauxite mine at Weipa. Comalco realises the need to strategically plan for future mining activities and still minimise the impact of operations on the natural resources of the region. With this realisation long-term forward planning has been implemented to improve the Company's ability to select future sites for mining, industrial use, agriculture, town expansion and conservation purposes.The knowledge of mineral, water, soil and animal resources has expanded dramatically in the past decade. During 1990 Cornalco purchased Geographic Information System technology which has allowed previously collected resource data to be presented in map form. These maps as part of the Life of Mine Land Use Plan are both information based and strategic which can be efficiently updated. The maps allow a broad audience from engineers, geologists, environmental scientists and site managers to government officers and the general public to comprehensively view and scrutinise the operations.

Jan 1, 1992

By Jiang G

The Chinese Central Government attaches great importance to the development of its coal industry. Besides carrying out the policy of simultaneous development of large, medium and small coalmines,the main strategy is to gradually modernize coal mining areas and coalmines and to increase the output from individual coalfaces. There are particular implications, processes and main experiences of coalmine modernisation in China.Ensuring a coal output of over one M tonne/yr from one coalface is a very complicated system-engineering project which deals with a wide range of problems. The most important measure used for achieving an output of over one M tonne/yr from a single coalface is the analysis of affecting factors on coalface production by means of the theory c reliability. Thus, as far as possible , the production stoppages caused by mechanical equipment failures and other factors are avoided, the equipment recovery rate is increased and the working hours of shearers are extended so as to ensure a high output and high efficiency.

Jan 1, 1991

By Mckenzie CK, Scott A

The injection of coal as an auxiliary fuel in ironmaking blast furnaces has been introduced on many furnaces worldwide. This paper examines the present practice of coal injection and discusses future directions for the technology. This has been undertaken through the use of a heat and mass balance model which predicts the replacement rates of coke by coal and the effect of coal injection on blast furnace productivity. The results indicate that future pulverised coal injection could replace substantial quantities of metallurgical coke, but that the energy balance economics of individual steel plants will have a dominating influence on the future of the technology.

Jan 1, 1987

The philosophy of computer control of grinding and flotation at ZC/NBHC is presented. The performance and reliability of the in- stalled systems are discussed.

Jan 1, 1978

By R A. Medower

This paper provides a glimpse into the future of minerals processing with emphasis on æAutomation InnovationsÆ for the new millennium, particularly those involving advanced process control and innovative new applications of process control technology in 2007.

Jan 1, 2000