Search Documents

By Bond W. F, Sharry P. V, Onley P. G

The use of Decision Analysis is becoming more widespread in industry as a whole, and there is considerable scope for its application in the mining industry. Wherever decisions have to be made, whenever risks have to be taken, whenever uncertainty exists or whenever judgements have to be made, then Decision Analysis can be used. In the mining industry we daily make many decisions involving risk, uncertainty and judgement. Expansion and diversity will only increase the need for balanced decision making techniques. This paper seeks to describe the history and principles of Decision Theory, and to illustrate the various modelling approaches using three fictitious yet realistic case studies. Decision Analysis logically integrates the quantifiable and seemingly non-quantifiable aspects of a decision problem into a coherent, explicit and rational solution. It also allows the decision-makers to see the full impact of each variable or uncertainty, and hence focus on the key aspects that influence the solution.

Jan 1, 1996

By Rose CW

Typical rehabilitation programmes for spoil piles and waste dumps in open cut coal mines involve the spreading of topsoil to assist vegetation growth. In the early years of rehabilitation before a protective vegetation cover has been established, this topsoil is susceptible to erosion during rainfall events. Since the long term success of rehabil- itation procedures is sensitive to adequate topsoil maintenance and since, on many mine sites, topsoil is a scarce resource, erosion losses of topsoil (particularly once fert- ilised) can severely restrict rehabilitation Measures.

Jan 1, 1983

By Buizen M

An investigation into the mechanics of sub-surface deformation caused by caving of the extracted area behind retreating longwall faces has been completed by the Subsidence Engineering Section of the New South Wales (NSW) Department of Minerals and Energy. Changes in strata bulk permeability were also measured by standard packer tests undertaken before and after mining. The strata movement was measured by a multi-wire borehole instrumentation system consisting of mechanical anchors installed at different horizons in a borehole extending from the surface to the coal seam. The mechanical anchors were collected to suspended weights on the surface by stainless steel multi-strand wires. The movement of these weights was monitored as the longwall face approached and retreated past the borehole. The anchors did not move significantly until the face went past the borehole. For subcritical extraction geometry with the extraction width to mining depth ratio of 124, the caving zone extended to roughly 9 times the extracted seam thickness above the seam roof. Tensile strains within the overburden tended to be much more closely related to stratigraphy than to the proximity to the extracted seam roof. Larger tensile strains were associated with layers of sandstone, siltstone and conglomerate, whereas layers of mudstones, claystones and coal underwent much smaller strains indicating subsidence in blocks. A beller correlation was observed between pre-mining Rock Quality Designation and permeability than between rock type and permeability. This correlation was less evident in the post-mining core logs. There was an overall increase in bulk permeability after mining.

Jan 1, 1990

By Torckler L, Brathwaite R. L

At Neavesville gold-silver (electrum) mineralization occurs in steeply-dipping zones of intense fracturing, brecciation and quartz veining within rhyolitic pyroclastics, carbohaceous shales and andesites. Hydro- thermal alteration extends over an area of greater than 3 by 1.5 km. In rhyolitic tuffs, highly silicified zones containing quartz- adularia-illite assemblages are flanked by less silicified assemblages composed of albite, illite-montmorillonite and chlorite. The mineralogy ana sequence of alteration are comparable with the alteration zones which envelop the steam-producing fissures of the active Wairakei and Broadlands geothermal fields. Primary fluid inclusions in quartz from five fissure veins in the Neavesville field show maximum homogenisation temperatures ranging from 220 - 260¦C and salinities of 0.0 - 1.1 wt. % NaCl equivalent, which cover a similar range to actual measured temperatures and salinities in geothermal fluids at Wairakei aria riroaolan¦s. The age of the rhyolitic pyroclastics and related alteration and mineralization is probably Pliocene and Neavesville therefore represents a fossil geothermal system.

Jan 1, 1980

By Wilson GR

Pellets were produced from carefully sized iron ore and silica sand fractions, under controlled moisture conditions, using a sealed balling drum. The strength of these pellets was measured as a function of moisture content and particle size. The results showed that the strength of the pellets could be adequately described by a model which equates the strength of the pellets with the negative pressure developed within the porous mass, provided that the particle size distribution was narrow and the mean particle size relatively large. However this model failed to account for the observed strengths of pellets produced from systems containing even small quantities of ultrafine particles (

Jan 1, 1972

By P J. Harris, D J. Bradshaw

Surface oxidation of sulfide minerals, such as that found in the regions of a sulfide ore body near the water table, can have a significant impact upon flotation. This theme has been explored for Merensky ore type sulfides where an ore containing pyrrhotite, pentlandite and chalcopyrite was thermally oxidised and the role of potential remedies investigated. Back-scattered scanning electron microscope images are presented showing the oxidation layer which formed in the mineral surfaces. These oxidation layers were depleted in both sulfur and iron with incorporated oxygen. Flotation recovery rapidly decreased with increasing oxidation, particularly after 27 days and reached a plateau after 50 days. Up to 27 days, this effect could be partially overcome with higher collector additions. Oxidation had more impact upon the finer size fractions, particularly for pyrrhotite. For more heavily surface oxidised samples, ultrasonic treatment prior to collector conditioning was found to improve flotation recoveries. This treatment had the greatest effect upon chalcopyrite particles. Sulfidisation was successful in restoring the flotation recovery of the heavily oxidised sulfide minerals. Longer sulfidisation conditioning times were not conducive to good flotation recoveries of both oxidised pyrrhotite and pentlandite due to oxidation of the freshly formed sulfide surfaces. For maximum flotation recoveries of oxidised pyrrhotite, pentlandite and chalcopyrite, different sulfidisation conditions are indicated. It appears likely that in a mineral processing operation treating oxidised Merensky type ores, two stages of sulfidisation employing different conditions would be required.

Jan 1, 2005

By A T. Bernardes

Using the cellular automata computational technique it was possible to simulate the generation and discharge of an iron ore pellet pile inside a direct iron reduction oven, as well as to calculate the reduction degree of the pellets as they leave the oven. It allows simulation of the variation of operational parameters and verify the results of those variations in the pellet reduction degree. The simulated data was validated in two instances: for the dynamics of the pellet flow inside the oven it was used in an acrylic bi-dimensional silo; and data from direct reduction iron literature was used for validation of the pellet reduction. The simulated results were considered acceptable to describe the movement of the iron pellet inside the direct reduction iron oven and to describe the iron pellet reduction direct in the oven.

Sep 26, 2011

Most of the gold reef mined today in South Africa is approximately 1 m in width with slopes about 30 m long. To prevent production interruptions it is essential that the stopes should not be blasted in sections. The shortage of experienced labour and arduous working conditions at the face dictate the need for simple blasting techniques.Hence, a pyrotechnic blasting system of sequential firing is in use at present, although research work to improve this technique is in progress.

Jan 1, 1985

The Ocean Drilling Program is the largest international geoscience project in the world, and the state-of-the-art drill ship, the JOIDES Resolution, is permanently at sea. Each year there are six scientific cruises (Legs) which each last approximately two months. These legs are designed by geoscientists from the 19 countries that subscribe to ODP. Australia and Canada share ODP membership under the banner of the AUSCAN Consortium. The Australian Secretariat of the ODP is housed at the Department of Earth Sciences at James Cook University, along with the AUSCAN Consortium office. The Canadian Secretariat is presently based at the University of Toronto. Both secretariats have major research interests in the ore deposits, both ancient and modem, and so there is currently a major drive by the AUSCAN ODP Consortium to make available data and technological information to the minerals industry. This type of information includes data from drilling hydrothermal sites such as the hydrothermally active TAG black smoker complex on the Mid-Atlantic Ridge, drilled during Leg 158, and the Middle Valley sulphide deposit, on the northern Juan de Fuca Ridge, which was drilled during Leg 139.

Jan 1, 1996

By Rivers CJ

The Brolga deposit is a Ni-Co enriched laterite, formed over intensly serpentinised peridotites of the Marlborough Block. Basement lithologies at Brolga consist predominantly of serpentinised dunite, with lesser massive serpentinite shear, gabbro and harzburgite. Investigation of the deposit has defined 17 different varieties of saprolite, ferralite (limonite), and ferricrete. Different combinations of these varieties form three distinct lateritic associations, the Hard, Soft and Dyke Associations. Recognition of key textural and mineralogical features in each association, an understanding of basement geology, and an awareness of current climatic conditions, suggest that: 1. both the Hard and Soft Associations have formed under relatively dry climatic conditions; 2. the Soft Association reflects much poorer groundwater drainage than the Hard Association; and 3. the Dyke Association has formed from a gabbroic basement, and has also been affected by restricted groundwater drainage, caused by poorly permeable marginal serpentinite shears.

Jan 1, 1996

By Mould G. R

The paper presents a general background to the subsidence research programme being undertaken by the Department of Mineral Resources and Development in New South Wales. The results of the studies undertaken over the last ten years are summarised. The differences between these results and those obtained by the National Coal Board are discussed. The results of a study carried out on the effect of total extraction beneath a freeway in the southern coalfields are discussed in some detail. The procedures developed for the const- ruction of a 500 mm diameter natural gas pipe- line crossing a number of collieries in the northern coalfields are also outlined. The future direction of the Department's subsidence research programme is discussed.

Jan 1, 1980

Metsim is proving to be a powerful tool when designing a heap leach operation. The most useful outputs arc determining the fluctuations in pregnant solution recovery rate, make-up water rate, gold recovery rate. and pond levels. Detailed data are needed for input: a pad loading schedule, a mining rate schedule for each ore type, column leach test data for each ore type, column tests on water dynamics (ie hourly flow-out versus-in during saturation and drain-down), monthly rainfall and evaporation data, and proposed pond dimensions. These data allow 'what if' studies on application rates, leach rates, loading rates and other variables of interest. Examples will he given of modelling both a rectangular pad and a valley fill operation.

Jan 1, 1994

The Auscoke project has reached-a stage where a pilot plant nominally able to produce 100 t.p.d. of coked briquettes is being brought on stream during Nov. 1971 . The targets for this stage of the project are to establish the technological and economic value of Auscoke for the iron blast furnace, and to verify the commercial feasibility of large scale plants. The project originated at the B.H.P. Central Research Laboratories (C.R.L.) and work to date has shown that using a two stage contin- uous process, strong large coke can be produced at good productivities from medium or low volatile poorly caking coals. General features of the pilot plant and processing are discussed.

Jan 1, 1972

By Hannington MD

On the southern flank of Lihir Island, a group of three volcanic cones were discovered at water depths from 1000-1500 m. The volcanoes are located in a narrow zone of recent seismic activity and elevated heat flow (up to 100 mW/m2). The recovered rocks consist of fresh alkali-olivine basalts, clinopyroxene-rich basalts, and porphyritic phlogopite basalts. One of the volcanoes has a recently erupted ejecta blanket (recovery of warm ash!), containing a suite of abundant mafic to ultramafic xenoliths. These xenoliths appear to represent a unique cross-section of subduction- modified mantle material sampled by volatile-rich primary fore-arc magma during its ascent to the seafloor. The most spectacular finding was the discovery of an active hydrothermal system with associated vent fauna and mineralization at Edison Seamount, and the recovery of unusually gold-rich (up to 43 ppm Au) hydrothermal precipitates in 1050 m water depth at the top of Conical Seamount, only 25 km south of the world-class epithermal Ladolam gold deposit on Lihir. The discovery of submarine hydrothermal vents associated with highly alkaline, quartz-undersaturated fore-arc volcanics represents a significant departure from similar hydrothermal systems on the mid-ocean ridges and in back-arc basins. The high gold grades in hydrothermal precipitates at Conical Seamount may indicate the first documented example of a shallow-marine epithermal system analogous to those known on land, and has important implications for the gold potential of submarine arc environments.

Jan 1, 1995

By Waters A. G, Nightingale R. J

The quartzite added at the blast furnace for the purpose of adjusting the chemistry of the burden inputs is shown to have a disproportionate impact on both the level and the variability of the hot metal silicon (HMSi). This conclusion is supported not only by direct correlation involving data from five blast furnaces, but also by mass balances. In one case the R2 correlation coefficient was 0.96 and the mass balance was accurate to within five per cent for a wide range of quartzite additions. The results indicate that as much as 43 per cent of the silicon in the added quartzite reports directly to the hot metal. Indeed, silicon from quartzite was found to be much more likely to report to the hot metal compared to silicon from regular sources (eg coke and sinter), reflecting differences in the activity of the silicon source.

Jan 1, 1994

By Nguyen G. H, Graham J

A laboratory-scale fluidised-bed roaster has been used to examine the effect of temperature and duration of roast on the morphology of the calcine produced from a pyritic gold-bearing concentrate. Two mechanisms of oxidation, which depend on the roasting temperature, have been identified. For samples roasted below 550°C, direct oxidation of the sulphide occurred to form hematite with a porous fine-grained concentrically-layered texture. The surface area of the calcine increased with an increase in roasting temperature in the range 400 to 500°C. For samples roasted above 550°C, the first reaction was the evolution of sulphur vapour to produce pyrrhotite, which underwent increasing grain growth as the roasting temperature was increased. This had the effect of decreasing the surface area of the calcine. The pyrrhotite was subsequently oxidised to produce hematite.Leaching studies using cyanide solution indicated that gold extraction around 95 per cent was achieved at temperatures of 500°C and above, with optimum extraction, taking into account rate and cyanide consumption in the range 550 - 700°C. Hence recovery did not decrease with decrease in surface area of the calcine. Observed gold in leached calcines was mainly enclosed in thin oxide walls of the hematite, with minor quantities enclosed in quartz and silicate minerals.

Jan 1, 1995

Design and construction techniques used to develop two highway tunnels in inaccessible mountainous terrain are described. Measures used to adapt the design to the unusual geology and topography are discussed, as well as measures to adapt the construction methods to available equipment, materials, and skills. Sharp local variations in geoloqic conditions resulted in field modifications to both design and construction techniques. The geology is a volcanic ash and breccia-agglomerate at one site, a jointed andesite at the other, which is also the site of a major landslide. Both rock reinforcement in the form of pretensioned and grouted rock bolts with a shotcrete lining,and rock support by struc- tural steel sets with a reinforced concrete lining were used. A canyonside location and high lateral in-situ stresses required modification of design procedures. Pilot tunnels at both sites resulted in adapting the designs to site conditions with large savings in lining costs, disclosing problem areas in advance of the main excavation, and cushioning of blasting pressure to minimize stability problems.

Jan 1, 1976

It is no longer satisfactory to assess the value of a coking coal on its intrinsic properties alone, its value depends upon its behaviour as a component in a blend. No single test can be used to make this assessment, it can only be made by carrying out a suite of tests. The quality parameters which are considered desirable, and which have widespread acceptance, have been discussed and their application to the blending of coals from New South Wales and New Zealand has been reported and discussed. Blending can be utilised to offset deficiencies, or capitalise on advantages, of the individual coals making up a blend. Coals can be blended, which alone are poorly coking, but which have compensating features. Blending also allows better exploitation of coking coal Reserves..

Jan 1, 1980

By B C. Povey

HPGR technology has been used at a number of magnetite mines in the world and have significant energy advantages over SAG and AG technologies. The early design at Los Colorados in Chile has been in operation for more than 12 years - and operates very successfully though only reduces the feed size to -5mmThe Whyalla project magnet design pushed the concept to produce a preconcentrate of 80%-350micron - a significant reduction on previous plants though with some wear problems in the early years. The Karara design backpedalled slightly and will only crush to 80%-1.8mm.However, the design issues of using a HPGR to further reduce the feed size continue to be explored. The aim is to reduce the process risks associated with wear and also to reduce the complexity of the downstream process - with consequent benefits in terms of capital and operating costs.The designs are being developed for a couple of projects - one planned to produce 20Mtpa of concentrate with the potential to not only remove SAG and AG milling but also ball milling. The concept is to use multiple passing through the HPGR since, on the data available, the efficiency of the HPGR to reduce size does not significantly diminish as the feed size is reduce. This can be have benefits in both capital and operating cost.CITATION:Povey, B C, 2013. Pushing the use of high pressure grinding rolls in magnetite circuits, in Proceedings MetPlant 2013 , pp 176-189 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By Liu Q, Siefken T. C, Misra V. N

The bubble size was measured in a laboratory flotation column. The effect of variables such as air flowrate, frother dosage and type, pulp density, particle size and water column height on the bubble size was investigated. The results show that an increase in either air flowrate or pulp density cause the bubble size to increase, while increases in water column height, frother dosage, surface tension or solid particle size cause the bubble size to reduce. Among the frother types tested, MIBC was found to be the most effective in reducing the bubble size.

Jan 1, 1992