Search Documents

This paper addresses the role of mine geology in mining geotechnics. The role is assessed and discussed in terms of five main elements; geotechnical complexity, geological complexity, mine scale, percentage sampling and geological uncertainty. Lastly, the overall objectives and mine geology requirements are listed in terms of the various mine development stages; exploration, feasibility-design and operating.

Jan 1, 1993

By S K. Ray

Open fire in a mine gallery causes large-scale damage to property and sometimes precious lives. Such fires produce two distinct effects, the throttle effect and the buoyancy effect. These effects disturb the ventilation system of the mine. To understand the complex dynamic phenomenon of open fire and its effect on ventilation systems, a mine fire model gallery has been designed and constructed at Central Mining Research Institute, Dhanbad. Two sets of experiments at air velocities of 1 and 1.5 m/s were conducted in the gallery using coal samples from the Dobrana seam of the Raniganj coalfields. After about an hour of development of fully-fledged fire, heavy backlash, with smoke and fumes, was observed. At the time of backlash occurring the gallery was divided into two zones. In the region of the gallery from the base up to 1.4 m the airflow was normal, in the remaining upper portion the airflow was the reverse. Air quantity reduced substantially, while pressure dropped across the fire zone, the products of combustion (POC) and temperature increased during the period of the throttle effect. It has been revealed from these studies that with an increase in airflow, pressure drops across the fire zone, POC, temperature and reduction in airflow increases. This paper addresses the important design features of the gallery, the instrumentation system, the experimental procedure and assesses the effect of open fires on mine ventilation systems.

Jan 1, 2005

The paper will review the marked upsurge in the installation of new continuous metal coating lines, both hot dip and electrodeposition. Although some of this new capacity has been replacement for obsolete facilities or directed at traditional markets, eg building products, consumer durables etc, by far the major portion is targeted at the automotive industry. The reasons for the rapid growth of coated automobile panels are discussed. A comparison of the installed capacity with projections for this market indicate that a severe over-supply situation has arisen. Many coatings are now available for the automotive industry, each with their own strengths and weaknesses, but none as yet wholly satisfactory. Coating development has mainly been cost driven. This favours hot dipped coatings, providing surface quality and pressing problems can be overcome. The high cost per unit thickness of electrodeposited coatings has also seen pure zinc coatings being replaced by thinner, more corrosion resistant alloy coatings such as zinc-nickel and zinc-iron. Recently resin overlays have been introduced to improve the performance of electrodeposited coatings. Developments in coatings for the more traditional markets will be described. The fastest growing market in the last decade has been prepainted product for the building industry. This has led to the installation of extra painting capacity and again it appears an excess capacity situation has occurred. Over the same period the traditional zinc coatings have continued to lose market share to the zinc/aluminium alloy coatings, Galvalume and Galfan. These have been joined recently by '1'aiyo Crack-Free which has been taken up by some metal coaters. Galvalume is now widely accepted as being the best available coating for unpainted applications. It is also suggested that 'spin-off' coatings from automotive developments might find a niche in the consumer durable market. The end users of coated products, particularly the automotive industry, have demanded improvements in quality, such as surface smoothness, formability, etc. At the same time the new coating lines have to process wider strip and run at faster speeds. To reconcile these somewhat incompatible needs has required numerous process improvements, many of which need in-line instrumentation and computer control. The more important of these changes are discussed briefly. Finally the paper will describe the recent developments which have occurred in continuous galvanising in Australia and put them into context with the rest of the world.

Jan 1, 1993

By Hossaini SMF

After reviewing the various approach es,namely, empirical,analytical.observational and numerical, a logical systematic approach is proposed for the estimation of compressive strength of coal pillars. In this approach first,uniaxial compressive strength of coal in pillars is estimated,taking into account the size effect and the effect of discontinuities. Next,the compressive strength of coal pillars is estimated by determining the stress distribution in the pillar and the Bieniawski strength criterion. The results appear to be compatible to the ones obtained by Wilson's method. The traditional pillar design equations give improper answers for deep workings.

Jan 1, 1991

By F Grobler

Many projects fail because project performance in unfavourable economic conditions was not anticipated at the investment decision stage. This type of failure may have been avoided through the selection of a strategy that enables the project to perform well under a range of possible future economic conditions (a ærobustÆ strategy); rather than an æoptimalÆ strategy for expected future conditions that will never eventuate. This paper describes a method of rapidly generating mine plans for a number of project strategies, and then evaluating it against a representative range of equally likely economic conditions. The key performance indicators derived for each strategy are the mean value and the distribution of values (variance). A prudent investor will identify prospective strategies not only on the merit of highest mean values (as a proxy for economic reward), but also on the probability of not meeting specified investment hurdles (a proxy for risk). A robust strategy will achieve its financial objective even under adverse economic variations. This paper focuses on the effect of commodity price uncertainty; particularly around the choice of mining and processing capacity levels. Results from enumerating 2000 prices scenarios against 63 strategy combinations show how processing and mining capacity can be manipulated to manage the risk-reward trade-off.

Sep 26, 2011

By B Gyngell, P Culvenor

Large language models (LLMs) have generated a lot of hype since ChatGPT was released in early 2023. In essence, they allow people to interact with computer systems through natural language and have the ability to generate highly complex text, images and videos (Patil and Gudivada, 2024). It is clear that this technology has significant potential, however most mining companies have not yet found practical applications for it within their operations. In this paper, we present a range of such applications along with the tactical considerations associated with developing and implementing them. We have identified use cases across a variety of operational and functional areas within the mining industry and evaluated them based on their potential business value and ease of implementation. Firstly, we provide an overview of how LLMs work and a review of how LLMs are being applied in other industries to provide best practice inspiration for mining. Next, we present a list of possible applications in mining and a critical assessment of each use case. This section also includes a technical deep dive into the different methodologies for developing the technologies as well as an analysis of barriers to adoption within mining organisations. Finally, we share a discussion of the potential path forward for LLMs in mining and the impact they could have on the industry. We analyse the potential differences between early adopters and laggards in the artificial intelligence (AI) space. This research draws on interviews and surveys with artificial intelligence experts as well as mining subject matter experts to connect cutting edge thought leadership with the specific problems faced by our industry.

Sep 1, 2024

A relationship is predicted between oxidic nickel in slag, oxygen in matte and Ni/Fe ratio in matte after the examination of thirty sets of contiguous matte and slag samples taken from industrial nickel smelters. Oxidic nickel in slag is found to increase with increase in oxygen content of matte of constant Ni/Fe ratio, and it is proposed that the relationship may be used to predict nickel solubility in slag from a knowledge of matte composition alone.

Jan 1, 1979

By Zhen Y. Y, Cook A, Jell J. S, Fleming P. J G

Remapping of the Burdekin Basin has resulted in subdivision of the three interfingering basin-wide megafacies previously recognised in the Early to Middle Devonian Fanning River Group. Eleven carbonate and siliciclastic facies are now identified within the three megafacies, representing coastal plain, shoreline, nearshore, and shallow marine shelf depositional environments. The facies reflect two phases of a major transgression. An initial phase, in the Early Devonian, was confined to the far north of the basin, whereas a second, main phase, resulted in the encroachment of the sea from the east or southeast in the Middle Devonian.The proposed depositional model begins with the drowning of a coastal plain and the transgression of shoreline and nearshore facies between granitic and metamorphic headlands and/or islands. This was followed by the deposition of a patch reef and fringing reef complex including stromatoporoid and coral bioherms, biostromes, and oncolitic, crinoidal, and brachiopod-dominated banks/shoals, together with foreslopes and submarine channels, carbonate rubble deposits and terrigenous sediments. Sedimentation during the peak of the transgression was dominated by sheltered carbonate shelf facies, the maximum, flooding surface being recognisable across most of the Burdekin Basin. Progradation of muddy and sandy nearshore bay and shoreline facies soon followed, terminating carbonate deposition.

Jan 1, 1990

Traditionally, the Lead Lode at Broken Hill has been represented on presentation plans, cross sections and diagrams in scientific papers as a solid black mass, around which the more 'interesting' and 'structurally useful', wall rocks appear to wrap. Structural analysis of the Broken Hill orebodies has usually turned to these wall rocks to determine the structural history of the mineralisation.This tendency to represent the orebody as a massive single entity is incorrect and the aim of this paper is to illustrate that sulphide orebodies (in this case Lead Lode), are a dynamic part of the mine stratigraphy. They can preserve a great deal of useful structural information that can be recorded with detailed internal mapping.Three main categories of ore type are recognised in Lead Lode; Stratiform ores, Mobilised ores and Metasomatically altered ore. The ore types in these categories occupy or have formed in distinct structural and stratigraphic positions and have clearly recognisable inter-relationships.

Jan 1, 1993

By Hara Y, Arino S, Nakamura M, Tachimori M

The theoretical and experimental studies have been done to clarify the hearth flow of iron and slag. The results of dissections show that the hearth can be treated as a packed bed of coke hav- ing good permeability with a coke-free layer at the bottom of the hearth. 3-dimensional numerical calculations of hearth flow with and without a coke-free layer are carried out, and the results are assured by a water model simulation. The influences of a coke-free layer on the iron flow and the discharge route of iron and slag are examined. The 3-dimensional flow pattern can be represented simply by the travelling time, which depends on characteristically the profile of coke-free layer and the quantity of iron in the hearth. Those flow parameters could be obtained by the results of radioisotope tracer test ( Co for iron flow, and Sc for slag flow) at several furnaces. As a result, it is found that the coke-free layer repeats the cycle of appearance and disappearance at several-month intervals. This cycle corres- ponds to large temperature fluctuation at the bottom of hearth. The relation between iron flow and skull (solidified iron, coke and deposited graphite mixed layer) on the hearth brick was studied by the model experiment and the thermal analysis based on the indications of thermocouples installed in the bottom of the hearth. If a thin coke-free layer is formed on the skull, a fast iron flow is generated in the layer, and melts away the skull. The growth and melting of skull produces the fluctuation of thermal load on a bottom brick, causing brick Damage.

Jan 1, 1981

Indigenous brown coals, which provide a readily available primary energy source, have played a significant part in the industrial development of Victoria. The deposits located in the Latrobe Valley compare in extent with other major deposits of brown coal in the world. Smaller but valuable deposits occur at Stradbroke, Gelliondale, Anglesea and Bacchus Marsh. Extensive drilling, aided by geophysical surveys, and detailed analyses of coal samples, have enabled the extent and quality of these Tertiary deposits to be Defined.

Jan 1, 1979

The application of new and currently practised mining techniques in new areas and at greater depths necessitates considerable and immediate research effort. This effort is aimed at identifying the factors which make a particular method suitable and economically viable in a given geological, structural and operational environment. These factors, together with greatly enhanced knowledge of a deposit at the exploration and planning stage, allow selection of the most appropriate and efficient mining method in a new area such that coal resource recovery is maximised in a cost effective manner. Current research and future requirements for research into mining methods and associated equipment and mine services are reviewed.

Jan 1, 1981

By J Jasper, L Koroznikova, J Begelhole

This paper outlines a comparison of heavy liquid and heavy suspension separation methods for iron ore characterisation.As part of Arrium MiningÆs program to improve its knowledge of ore types being processed in its two hematite ore beneficiation plants (OBP), metallurgical evaluation of hematite feed for the upgrading process has become a major focus.Iron ore deposits almost always contain more than one valuable (and relatively dense) iron mineral. Iron ores are found with a range of iron contents, giving rise to density variations.At present the industry relies on heavy liquid separation techniques for the evaluation of iron ore samples arising from exploration, mining or metallurgical processes. There are only a few high-density liquids available, which are both high-cost and highly toxic.Low-toxicity solutions that can be utilised at relative densities up to 3.0 have been developed. However, highly-toxic organic liquids are required presently to achieve relative densities beyond 3.0.Bromoform which has a specific gravity (SG) of 2.89, and diiodomethane (SG 3.31) are commonly used; both present significant health and safety hazards.æClericiÆs solutionÆ (mixtures of thallium formate and thallium malonate) provide liquids having specific gravities between 4.0 and 5.0. ClericiÆs solution is highly toxic and testing is currently conducted by a limited number of laboratories worldwide.An alternative to ClericiÆs solution and organic liquids is a low-toxicity, high-SG, suspension technique, which has been demonstrated successfully for heavy mineral sands. This heavy suspension method employs mixtures of fine tungsten carbide particles in lithium heteropolytungstate (LST) solutions.Heavy liquid separation is not commonly used as part of routine iron ore feed characterisation due to the expensive, toxic and time consuming nature of the technique. Our results show that the heavy suspensions method can achieve low-cost, low-toxic separation and are outlined and results compared with results using ClericiÆs solution presented.Heavy suspension technique provides a theoretical/absolute separation of a particular sample. By placing an iron ore sample in a suspension of a particular density, it produces two products: a sink fraction and a float fraction. As iron oxides-hydroxyoxides are denser than the gangue minerals associated with the ore, particles that have high iron content will sink and the particles with gangue association will float. This process is repeated over several densities, thus also enabling separation of the constituent iron ore phases. A theoretical grade and a theoretical mass recovery can be calculated. With these calculations, a grade-mass recovery curve can be constructed for any element that is of interest.This type of characterisation can be used to either prepare OBP feed-piles of known processing characteristics, or to benchmark the performance of the process against what can be theoretically achieved on a continuous basis.CITATION:Begelhole, J, Jasper, J and Koroznikova, L, 2013. Application of the heavy suspension technique for ore beneficiation plant feed characterisation from the Southern Middleback Ranges, in Proceedings The Second AusIMM International Geometallurgy Conference (GeoMet) 2013 , pp 269-278 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 29, 2013

By E M. Gama, L Resende

The tailings are waste from mineral processing operations. The type of tailings of iron ore processing are classified into sandy tailings and mud. Already the overburden are showing significant levels of useful mineral. Both iron ore`s waste have in your composition phyllosilicates/clay that indicates the potential for use in niche markets as paving and cement. According to several studies, there are various technologies in bench and pilot levels that could be used on a large scale but there is not an economic environment, tax, regulatory and tax set. Many of these technologies are associated with the reuse of tailings and overburden in construction. All these factors influence for that so many initiatives remain in search formats and cannot advance to the new business format. There is no way to set goals of reuse of this waste, as already occurs in China, if there is not a fiscal, tax and economic structure to support such measures. The way to foster and ensure that reuse of tailings and overburden is an incentive for promoting a culture of circular economy that would allow the emergence of an ecosystem between the private, public and Government sectors with the objective of accelerating and subsidize the entire network of reuse of this waste. The closure of the mine could be the tool used to ensure and boost this ecosystem of reutilization to align it with the vocation of the area of the mining law. Following this model, the end of the mining activity could provide a financial return to the local population, a more effective environmental compensation and a reduction in costs related to the closure of the mine. In this study are shown how the Vale is working in the reuse of tailings and overburden.CITATION:Resende, L and Gama, E M, 2018. The challenges of the reuse of tailings and overburden, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 117–125 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By G M. Jeffress, D C. Arne

There are two discrete aspects to collecting portable X-ray fluorescence (pXRF) data to obtain reliable results and to comply with reporting requirements under the 2012 edition of the JORC Code (JORC, 2012) – sampling method and quality assurance. A robust sampling program is required to obtain representative material for analysis. The appropriate method should be established for a particular project using a small orientation study. A variety of approaches to sampling soils, drill cuttings, rock faces and diamond drill core are discussed. These include using multiple spot analyses, scanning using a single operating beam and the collection of cutting saw pulps. The operator must also be aware of the attenuating effects of analysing through sample bags of different material types for various elements as well as the limitations of current pXRF instruments in reporting reliable data for certain elements. The analysis of the samples must also be accompanied by a quality assurance program in order to generate data that are ‘fit for purpose’. This includes recording X-ray tube resolution on a routine basis, using matrix-appropriate standards for which total elemental concentrations are available, using silica blanks, capturing sufficient duplicate analyses to constrain data precision and obtaining check assays to calibrate pXRF data against laboratory data. Examples of quality control approaches and data are presented. Table 1 of the 2012 JORC Code also recommends that information on instrument make and model, reading times and calibration be provided in any reporting of pXRF data. To this should be added information on operating mode and temperature, software version and moisture content of the samples. A robust sampling methodology with a suitable quality assurance/quality control program should produce pXRF data of sufficient quality for public reporting purposes, provided that the data are presented using appropriate cautionary language and adequate supporting information.CITATION:Arne, D C and Jeffress, G M, 2014. Sampling and analysis for public reporting of portable x-ray fluorescence data under the 2012 edition of the JORC Code, in Proceedings Sampling 2014 , pp 57–64 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 29, 2014

By Cocker A

Pre-splitting for smooth highwall formation is conducted in around 75 per cent of surface coal operations within Australia. The CMTE (Centre for Mining Technology and Equipment) in conjunction with BHPAC (BHP Australia Coal) initiated a project to look at pre-splitting and to investigate the notching of blastholes for fracture plane control. The notching was specifically for pre-split initiation and also for discing of the toe of the production holes to minimise coal loss from the top of the coal seam. There are currently a number of factors which are driving the introduction of new pre-splitting technologies and products. The first is the ever increasing bench height being employed in strip mines which require a higher quality wall with less blast damage to maintain stability. Currently depths of 55 metres are common place with depths of 70 - 80 metres fast approaching. The second factor is the introduction of new technologies or methods which require a high quality highwall produced, eg highwall mining. This paper discusses the current state-of-the-art in pre-splitting and the main issues facing successful pre-splitting in the future. The use of a blasthole notching technology to promote fracturing along the pre-split line is also analysed. The review indicates that most pre-splitting challenges in the future can be addressed through better use and developments of current drill and blast technology. It is also concluded that a blasthole notching technique may find niche applications in improving final walls within a surface coal mine, especially where a high quality wall is required. The notched blasthole method may also allow pre-splitting in ground conditions and adverse rock structure which currently cannot be pre-split by existing technology.

Jan 1, 1995

By M C. Ackland

The Grande Côte Mineral Sands Deposit (GCMSP) is located on a coastal mobile dune system in Senegal on the west coast of Africa. Senegal is a stable, democratic republic, having gained its independence from France in 1960. It has a population of about 12.5 million people. The dunes begin about 25 km north-east of Dakar, the capital city of Senegal, and extend northwards for more than 140 km. The mineralised dune system averages about 2 km wide with some areas extending to up to 4.5 km wide.Mineral Deposits limited (MDL), a Melbourne-based company with over 60 years operational experience in mineral sand mining in Australia, holds, through its Senegalese subsidiary MDL Senegal SARL (MDLS), a 25-year Mining Concession covering the deposits. The main heavy mineral (HM) areas identified to date are, from south to north, Mboro, Fass Boye, Diogo and Lompoul. Within the Mining Concession there is potential to identify additional resources beyond the limits of present drilling. The dunes are mobile or semi fixed, pale yellow in colour and overlie older white marine sands. The dunes range between 5 m and 30 m in height and the mineralised zones, which are essentially flat-lying, average around 15 m in thickness. The mineralisation consists, principally of ilmenite with accessory zircon, rutile and leucoxene. Zircon and ilmenite are the main commodities of interest.Independent consultants AMC estimated mineral resources for the four main deposits in 2006 of 1330 Mt of sand averaging 2.0 per cent HM at a cut-off grade of 1.5 per cent HM. At a cut-off grade of one per cent the resources were 3200 Mt averaging 1.5 per cent HM. All of the estimate was classified as Inferred Resources under the 2004 Australasian Code for Reporting of Exploration Results, Mineral Resources and Ore Reserves (JORC, 2004).Subsequent completion of infill drilling, sampling and assaying of the initial mining area, centred at Diogo, was completed in 2008, enabling a final dredge path to be designed and ore reserves estimated, based on a JORC compliant Measured and Indicated Mineral Resource. Infill drilling is continuing in the Lompoul and the results of this campaign will be included in the JORC compliant data base by AMC in April 2010 to enable the 15 per cent year dredge path and mine plan to be finalised.Development studies have shown that the project can be optimised as a dredging operation, with mineralised sand being treated in a conventional floating spiral preconcentrator, wet concentrator and dry mineral separation plant. Engineering work now substantially completed by Ausenco Limited (Ausenco) has developed the combination of some existing plant from MDL’s past operations, and new plant for the complete process from dredging to final product separation and grading. Testwork on a series of bulk samples has determined that the project can yield a high quality zircon product and an ilmenite product along with minor rutile and leucoxene.Work to date indicates a likely output of around 80 000 t of zircon in various quality streams (Primary, Secondary, Standard and Foundry Grades), around 550 000 t of ilmenite plus around 15000 t of rutile and around 12 000 t of leucoxene/secondary ilmenite. Planned zircon output would represent around 7per cent of the total world production, which would make the GCZ&IP a significant producer on a world scale.The studies have indicated capital costs to be in the range of US$400 M total operating cost (after completion of ramp-up) of around US$50 M - $55 M/a. Revenue is expected to be in the range $127 M - $157 M/a.

Oct 5, 2011

By I Canbulat, J Oh, A Mcquillan, D Payne

This paper presents a new risk assessment tool for coal mine excavated slopes. This new empirical-statistical Slope Stability Assessment Methodology (SSAM) is intended for use by geotechnical engineers at both the design review and operational stages of a mine’s life to categorise the risk of an excavated coal mine slope. A likelihood of failure is determined using a new slope stability classification system for excavated coal mine slopes developed using a database of 119 intact and failed case studies sourced from open cut coal mines in Australia. Consequence of failure is based on slope height and stand-off distance at the toe of the excavated slope. Results are presented in a new risk matrix, with slope risk being divided into low, medium and high categories. The SSAM is put forward as a new risk assessment tool to assess the potential for, and consequence of, excavated coal mine slope failure. Unlike existing classification systems, assumptions about the likely failure mode or mechanism are not required. Instead, the SSAM applies an approach which compares the conditions present within the excavated slope face, with the known past performance of slopes with similar geotechnical and geometrical conditions, to estimate the slope’s propensity for failure. The SSAM is novel in that it considers the depositional history of strata in an excavated slope and how this sequence affects slope stability. It is further novel in that it does not require explicit measurements of intact rock, rock mass and/or defect strength to rapidly calculate a slope’s likelihood of failure and overall risk. Ratings can be determined entirely from visual observations of the excavated slope face. The new SSAM is designed to be used in conjunction with existing slope stability assessment tools. CITATION:Mcquillan, A, Canbulat, I, Payne, D and Oh, J, 2018. New risk assessment method for coal mine excavated slopes, in Proceedings The Fourth Australasian Ground Control in Mining Conference (AusRock), pp 473–495 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 30, 2018

By G S. Beros, K M. Edwards

Over the past 20 years drum scrubbers have become a widely adopted technology within iron ore beneficiation plants. Generally, the drum scrubbers in use are considered high-capacity machines capable of accepting larger-sized feed material. Together with a water addition to a desired pulp density and a mild energy input, these large rotating machines effect an attritioning action that removes water soluble clays and other deleterious materials. Within the Western Australian iron ore industry, drum scrubbers have been successfully applied to Channel Iron, Marra Mamba, Bedded and Detrital orebodies. The introduction of drum scrubbers has enabled Western Australian producers to satisfy the substantial increase in demand for iron ore from Chinese steelmakers by making the lower-grade sections of the above orebodies economic. However, despite being a relatively simple unit process, the requirements for successful design and operation of these machines are not fully understood. This paper draws on the collective experience of both authors to provide some points to consider for incorporating drum scrubbers into iron ore beneficiation plant flow sheets.

Sep 18, 2023

Although forty-seven years have passed since the by-product coke oven made its successful commercial appearance, it is only during the past fifteen or twenty years that this system of coal carbonisation has advanced rapidly to its present position ofabsolute supremacy.Early designs of by-product ovens proved more or less faulty, and the coke produced was so inferior to coke made in beehive ovens that there was a natural hesitancy on the part of coke producers to invest large sums of money in installations of by-productovens of doubtful utility-more especially in view of the fact that beehive ovens could be erected cheaply and operated by non technical labour for the production of high-grade coke under the most variable conditions of trade.Surely and steadily designers brought forward by-product ovens of improved type, coupled with more efficient apparatus for the recovery of by-products, but still the industry lagged, due almost entirely to the insistence on the part of coke users that the qualityof ordinary beehive coke was vastly superior for metallurgical operations to the best coke produced from by-product ovens. So deep rooted was this prejudice that only the passage of time could eradicate it. That it has successfully done so is strikingly illustratedin the following statistics:

Jan 1, 1928