Search Documents

The Ranger Project Area covers 78.6sq km and is approximately six km east-west by 14km north-south (Fig. 1). The area is known to con- tain two uranium orebodies, Ranger No. 1 and No. 3, two uranium occurrences, Anomalies 4 and 5 and three significant radon anomalies, Ranger 18, 19 and 48. The Ranger No. 1 and No. 3 Orebodies con- tain approximately 120 000 tonnes of U308 in highly chloritised metasediments of the Lower Proterozoic Cahill Formation. The orebodies occur as suboutcrop and exhibit significant radiometric anomalies. These occur within approximately 400m vertically of the projected unconformity with the sandstone of the Middle Proterozoic Kombolgie Formation. Oxidised and reduced uranium minerals occur in quartz-rich schists containing variable muscovite, chlorite and sericite and in the chloritic matrix of chert breccia. Secondary uranium minerals namely saleeite, metatorbernite and gummite associated with earthy iron oxides occur from the surface to 50m depth in No. 1 Orebody and up to 80m depth in No. 3 Orebody. Below the oxidised zone, uranium occurs as pitchblende finely disseminated throughout sequences of quartz muscovite chlorite schist up to 150m thick and as open space fillings in zones of structural deformation. The uranium-bearing schists directly overlie up to 300m of dolomite and magnesite containing minor interbedded schist units and are themselves overlain by approximately 2 000m of more micaceous schists of the upper part of the Cahill Formation. Regional metamorphism has occurred to at least amphibolite facies and has been followed by retrograde metamorphism to a greenschist facies equivalent. The metasediments are intruded by granitic pegmatites and dolerites. Uranium is associated strongly with chlorite of which there are at least five textural varieties. Not all of the various generations of chlorite have associated uranium. Graphitic schist horizons occur which are often less than one metre thick and discontinuous. These are best developed at the base of the quartz chlorite schist sequence where uranium grades up to 1 000ppm U may extend for several hundred metres beyond the main ore zone. Uran- ium is not common in the carbonate sequences and only occurs in chlorite segregations in disrupted zones. The unoxidised ore contains sulphides, mostly pyrite, which are low in abundance (

Jan 1, 1984

By CorrOa de Araujo A, Salum MJG

The treatment of mining and metallurgical liquid effluents is becoming, everyday, a necessity felt by these industries. Physical-chemical and chemical methods for treating such effluents are generally necessary whenever heavy-metals and other toxic compounds such as cyanide are present. The present paper discusses the use of precipitate flotation as an alternative physical- chemical method that can be applied for the treatment of effluents containing heavy-metals (mainly zinc and cadmium) and cyanide. Examples of laboratorial scale applications on real effluents are given. In both cases precipitate flotation was able to reduce the concentration of toxic components of the effluents at a very high removal rate, generating a solid waste that can either be disposed, re-used or recycled. A cationic collector - dodecylamine hydrochloride - demonstrated to be the best choice of surfactant for the two systems investigated. Sodium sulphide and dithizone were selected for the precipitation of the zinc bearing effluent whereas a copper salt was preferentially used for precipitating cyanide in a form adequate for its recycling envisaging the use of an AVR (acidification - volatilisation - regeneration) technique.

Jan 1, 1993

By Singh BN, Chakravarty PK, Chatterjee LM

Indian blast furnaces operate with coke gener- ally containing 24 to 28% ash compared to 10-15% ash in coke in most other parts of the world. The operating problems are further aggravated by the high alumina content and the adverse alumina to silica ratio in the ore. The above factors not only increase the coke rate but, at the same time, increase the flush slag volume, make the bosh slag highly limey and thereby viscous, and produce a flush slag containing 24 to 26% alumina. Relative- ly low flame temperatures (RAFT) make conditions more difficult. The high basicity of the bosh slag limits the maximum flush slag basicity to around 1.0, beyond which the burden movement is adversely affected by the viscosity of the bosh slag: This effect is partly controlled by operating blast furnaces with high MgO in the flush slag (around.10%), which also improves the desulphurizing power of slag. Steps are underway in some plants to inject lime through theòtuyeres to control the bosh slag basicity and also to neutralise the large quantity of silica which is released at the tuyere level from the coke ash, so that the silicon content of the hot metal can also be controlled. High bosh slag basicity coupled with the characteristics of iron ore/aggolmerates, widens the softening-melting zone and alters the shape of the softening-melting zone. This leads to operat- ing difficulties and poor hot metal quality. This paper discusses the above aspects of Indian blast furnace operation and steps being taken to surmount some of the above difficulties.

Jan 1, 1981

By Soma T

Pyrite and Cu-concentrate were roasted in vertically suspended state in an externally heated tube. Tubes of three different lengths of reaction zone were used for three different reaction times. Roasted ores were submitted to chemical analysis and the extent of roasting reactions was determined. In case of pyrite, extent of roasting reactions was not affected much by reactor length and heating temperature (above 500¦C), but was considerably by ore/air ratio. Micro- scopic and XMA examinations led to the conclus- ion that pyrite particles decomposed to pyrrho- tite and then pyrrhotite was oxidized to give Fe-S-0 melt, magnetite and hematite. The extent of reaction was not uniform in all particles but had a wide distribution from unreacted pyrite to completely oxidized particles. Combustion of Cu-concentrate from Kuroko complex sulfide ore ) was unstable under a uniform wall temperature of 450¦C, but proceed- ed rapidly at temperatures above 500¦C. Sticking of roasted ores to the wall of the reaction tube induced choking of the tube, caused by melting of roasted ores, at tempera- tures above 950¦C. Enrichment of oxygen exterted less influence on reaction rate than heating temperature of the tube. Particle size of ore had a big effect on reaction rate.

Jan 1, 1980

The 1980's have produced an outstanding revival of the Australian gold industry. In contrast to some previous mining booms, the economic aspects of the growth in gold production are soundly based. In general the new developments have been highly profitable and this is beneficial to all parties- whether they be government, shareholders employees or suppliers. Mining companies are showing a large commitment to gold exploration with approximately 50% of Australian exploration budgets now being directed towards gold. An increasing proportion of this expenditure is being channelled towards the eastern States with Queensland 'being the major centre of interest. Further strong growth in production is expected with some 50 projects likely to come on stream before 1990. A very significant aspect of the foundation for this growth is a continuation of the existing tax status of the industry.

Jan 1, 1987

By K Jupp, T J. Howard

Cliffs Natural Resources Pty Ltd (CNR) operates iron ore mines in the Koolyanobbing region of Western Australia. Ore is mined from three locations, separated by many kilometres. The ore is stockpiled at these locations, according to an in-house ore classification system (based on grade and source) and then trucked to the crushing and screening plant at Koolyanobbing. Lump and fines products are railed to Esperance for ship loading and export to Asian customers. CNR prides itself on the relatively low inter-shipment grade variability of the products. The Koolyanobbing crusher is fed using a daily blend plan, generated to maintain lump and fines product grades within acceptable tolerance ranges around targets. Achieving low variability requires predicting lump and fines grades as accurately as practical from the estimated head grades of the ROM ores potentially going into the blend. The grade prediction model may be either a direct prediction of crushed lump and fines grades and lump percentage, or be split into two stages: the bias between blasthole estimated head grade and crusher head grade and then the lump-fines algorithm for splitting the head grade between lump and fines products. The lump-fines algorithm comprises the percentage of lump and the difference between the lump and fines grades. We describe a weighted least squares (WLS) regression model for predicting crusher grades and lump proportion from the estimated head grade for Fe, P, SiO2, Al2O3, Mn and S. The method is applied to CNR production data, where the regression model explains approximately 60 per cent of the variance in the crushed ore grade, for both lump and fines. A further small but significant improvement in prediction can be achieved by including the ore classification data in the model. The regression errors exhibit strong positive serial correlation, indicating trends in grade error across multiple blend records. To compensate for the longer-term error, an exponentially smoothed model was developed and applied to the daily grade blend errors. This gave an increase in the longer-term variance explained and therefore an improvement in grade prediction.

Jan 1, 2009

By T Ma, F T. Suorineni, Q He, J Oh

Directional hydraulic fracturing was invented by Polish experts and was first applied in coal mining to prevent hard roof rock bursts. Based on its successful application in coal mining, directional hydraulic fracturing has the potential to reorientate the hydraulic fracture trajectory. Recently, this technique has been introduced into cave mining for the purpose of lowering breakdown pressure. The hydraulic fracture is much easier to initiate with the assistance of an initial notch. No systematic theoretical or experimental studies have been carried out to investigate the influencing factors in the hydraulic fracture reorientation process. In this paper, the numerical modelling software Realistic Failure Process Analysis3D (RFPA3D) – Flow Version is used to study the influence of the in situ stress condition and rock mass heterogeneity on directional hydraulic fracturing in brittle heterogeneous rock masses. Firstly, the reliability of RFPA3D in simulating hydraulic fracturing is validated by comparing its results with experimental results and the simulation results from the extended finite element method. The hydraulic fracture trajectory is then observed in a three-dimensional stress environment. The results indicate that for the in situ stress condition, when the borehole lies in the ?2–?3 plane, only the difference between ?2 and ?3 has an important influence on hydraulic fracture reorientation. Furthermore, rock mass heterogeneity is a key factor that must be accounted for when fracture reorientation is required.CITATION:He, Q, Suorineni, F T, Ma, T and Oh, J, 2016. Modelling directional hydraulic fractures in heterogeneous rock masses, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 369–384 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By M A. Rhamdhani, K Avarmaa, A Putera, J Chen, G Brooks

Silicon-based photovoltaic cells are currently the most dominant types applied to convert solar energy to electricity. In solar-grade silicon (SG-Si), the control of boron (B) and phosphorus (P) is very critical. Generally, these elements are difficult to remove into acceptable sub-ppm levels from lower grade Si. This study investigates slag treatment as a process for Si refining, focusing on the behaviour of P and B. The experiments were conducted by equilibrating Si-B-P alloys with 43 wt per cent SiO2 – 47 wt per cent CaO – 10 wt per cent Al2O3 slag under inert atmosphere at 1500°C. Different crucible materials were used (Al2O3, SiO2 and MgO), which determined the primary saturation phase for the system and modified the final slag composition accordingly. The samples were equilibrated and analysed with microanalysis techniques (EPMA (electron probe microanalysis) and LA-ICP-MS (laser ablation inductively coupled plasma mass spectrometry)). New standards were prepared and applied in the LA-ICP-MS analyses. Experimental results show that silver is essentially fully dissolved in silicon, as well as most phosphorus with LP ( = wt per cent P in slag/wt per cent P in Si) between 0.1–0.3. The distribution coefficient of boron was measured to be between 1 and 2. The crucible material used had an influence on the phase compositions and slight influence on the distribution coefficients of boron and phosphorus. The experimental results provided new accurate data when considering applicability of slag treatment as a technique for Si refining and Si PV cell recycling.

Jun 19, 2024

By B G. Lottermoser

Field and laboratory data combined with computational modelling have been used to predict the pit water quality for the Highway Reward mine. Open pit mining of the Highway Reward copper-gold deposit has produced a final mining void with a diameter of 600 m and a depth of 280 m. This void will be left to fill with ground and surface water once pumping of pit water ceases. Several leaching tables were constructed to simulate weathering reactions and surface water run-off in the major pit wall units during a 200-day leaching experiment. To date, about three-quarters through the experiment, combined run-off from these cells has reached a pH

Jan 1, 2003

Jan 1, 2004

By C Harwood, EáWestman, K Luxbacher

Testing of in situ seals in underground coal mines is critical to determine seal integrity and to provide safe working conditions. In the wake of the 2006 Sago Mine explosion, the United States of America (USA) promulgated the Mine Improvement and New Emergency Response (MINER) Act (USDOL, 2006) which required mines to install 827 kPa (120 psi) rated seals or monitor and maintain the atmosphere behind existing 345 kPa (50 psi) seals. The purpose of developing the regulations was to prevent the breaching of seals in the event of an explosion in the sealed area.While seal design and construction is carefully regulated in practice, the construction of seals is difficult to monitor, as many are constructed under various mine conditions and the methods rely on prescribed placement of the seal material. Further examination of installed seals is limited to two-dimensional visual inspection and atmospheric and convergence measuring devices. These methods do not accurately reflect the integrity of the seal and cannot detect changes, deterioration, or defects within the seal.If detection of defects, deterioration and damage is not possible, unexpected communication between the active and sealed areas may result. Additionally, the ability of the seal to withstand explosions may be compromised. Non-destructive testing (NDT) of underground mine seals is necessary to investigate if the seal properties have been altered and if the seal remains functional as a barrier between active areas and sealed areas of the mine. This paper gives a preliminary assessment of proposed NDT methods for seal evaluation using radio frequency (RF) technologies and tracer gas methods.CITATION:Harwood, C, Luxbacher, K and Westman, E, 2013. Non-destructive testing of in situ underground mine seals - Initial technology assessment, in Proceedings The Australian Mine Ventilation Conference , pp 299-306 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By D Giddings, S A. Silvester, S Pickerin

Underground fires represent a constant threat to the safety of underground personnel. Miners in the immediate vicinity may face intense heat, blinding smoke, toxic fumes, fall of ground and other direct effects of a fire. However, the vast majority of victims never actually see the fire, and are overcome either by deadly fumes in the ventilating current or by asphyxiation. The mine ventilation system, which maintains a sustainable atmosphere to the working places, can transport products of combustion with equal efficiency. Miners who are remotely situated from a fire may be forced to evacuate considerable distances, through dense smoke and fumes, or even become cut-off from escape. Additionally, miners may become confused by unfamiliar ventilation characteristics caused by fires. Conveyor belts are widely used for transporting minerals in mines as well as in many other industrial situations. Because they contain large amounts of polymeric materials their use in certain environments, especially coal mines, but also in steel works, power stations and other enclosed areas must be controlled to minimise the fire risk. Over last nine years there have been 60 fires in underground mines in the UK alone and that of these, half have been associated with conveyors. This paper summarises the results obtained from a recent research project that has developed a preliminary computational thermal and fluid dynamic model to represent the spread of flame along a typical conveyor belt used in UK deep coal mines. The results of these models have been calibrated against a series of experimental tests performed within a surface fire test gallery. An improved knowledge of the burn characteristics and rate of release of the products of combustion from conveyor belt fires will assist in the development of better fire detection and fire fighting techniques.

Jan 1, 2005

Recent and on-going studies on the leaching of gold, the properties and activity of carbon, developments in the elution of gold from carbon, and methods of recovering gold from solution are reviewed. Emphasis is placed on Australian contributions, and their impact on gold metallurgy. Consideration is given to the future development of selective solvent extractants, ion exchange resins or alternative reagents for cyanide.

Jan 1, 1987

By S Vearncombe

SpaDiSÖ is a revolutionary approach to the spatial analysis of point data using geometry to analyse geometry! SpaDiSÖ uses each and every spatial relationship and is not dependent on mathematical models. For n points there are n2 û n spatial relationships and, because of the square function, the method yields interpretable results for both small and large data sets. SpaDiSÖ is an alternative to variography for directional studies. At the regional scale, the analysis can assess distribution patterns of mineralisation and potential controlling structures. At the deposit scale, the characteristics of zones of mineralisation such as direction, spacing, high-grade ore direction and grade distribution can all be deduced.

Jan 1, 2000

By X Dahe

SLon vertical ring and pulsating high gradient magnetic separators possess excellent mineral processing ability and have been widely applied to process oxidised iron ores. SLon centrifugal separators are applied to clean the SLon magnetic concentrate and remove quartz and other gangue minerals associated with a small portion of magnetite.This paper introduces the application of this technology in Hai Nan, Da Hong Shan and An Shan for processing oxidised iron ores.

Jul 11, 2011

To reflect on the early history of mining in South Australia requires considerable imagination and rashness. The people who were the chief actors in the scene have long since passed away. Accounts of their activities are hazy and debatable. A broad brush account is all that I can hope to accomplish under these circumstances. It is fitting that a picture be painted and possible lessons learnt from the achievements of our pre- Decessors.

Jan 1, 1987

By M D. Uttarwar, R R. Yerpude

India is the world’s third-largest producer of coal and is endowed with the fifth-largest coal reserves in the world. Surface mining straddles the entire domain of the Indian coal mining industry, yielding over 88 per cent of production. With continually rising domestic demands, it has to shoulder the responsibility of sustaining the requisite increase in coal production and chasing commensurate stripping targets. Such an ambitious task calls for the deployment of smart technologies. In such a demanding situation, cast blasting of overburden has emerged as a promising alternative for enhancing production and productivity of dragline pits.The cast blasting technique reduces stripping costs significantly as it utilises the chemical energy of explosives in place of mechanical energy to move large volumes of overburden quickly. Proper application of cast blasting not only reduces overall mining costs but also increases coal production. This paper investigates and evaluates the potential of the cast blasting technique, with special reference to dragline pits employing the rehandle method of extended bench. The economic feasibility of the technique is also ensured under different scenarios so that considerable benefits would accrue to the individual surface coalmines. To underline the efficacy of the technique, different cast blasting models have been formulated under a range of operational and economic scenarios that resemble present day practices in India. In order to test for economic variability in the application of the technique, a risk analysis of all the formulated cast blasting models is performed using net present value.CITATION:Uttarwar, M D and Yerpude, R R, 2015. Potential of the overburden cast blasting technique in Indian surface coalmines – a modular approach and its financial implications, in Proceedings 11th International Symposium on Rock Fragmentation by Blasting, pp 655–664 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 24, 2015

By Wilson R. G

Mining conditions imposed by a coal seam roof can be analysed according to natural causes, before consideration of strata control. All types of roof behaviour can be explained by considering only three independent variables. They are roof rock types, rock stresses and discontinuities. Roof rock types encountered in the Sc.ithern Coalfield of New South Wales (NSW) are sandstone, shale, mudstone, laminite and coal. Each rock has its own mode of failure. Lithological stability of the sediments varies from one type to another. Regional stresses upon a coal seam roof will vary in magnitude according to the proportion of gravitational stress, which is related to depth of cover, and residual stress, which is related to the maximum depth of burial and may be gauged by coal rank. Local stresses will vary according to tectonic deformation, related to irregularities in seam structure.

Jan 1, 1976

By Hoppe AJ

Drilling and shooting techniques at Moura open-cut have evolved over a period of 16 years and are the result of hard earned experience combined with established practices and consul- tation with professional services. The wide range of overburden types encoun- ted in the field requires varying methods to achieve the best results at all times. Safe working conditions for the employees and protection of mining equipment is of para- mount importance and close liaison is maintain- ed with the Department of Mines Queensland to keep abreast with changing legislation. Drill patterns, charging profiles, types of explosives and ultimate results are des- cribed in detail along with a resume of equip- ment. Costs of drilling, labour and explosives are also analysed with a total of approximately 20c per cubic metre of shot ground. Future developments and improvements to facilities are also outlined.

Jan 1, 1978

By Q Liu

Open stoping is one of the widely adopted methods in underground bulk mining. In this method, fanned or parallel holes are often drilled from a top sill down to a sublevel in the ore zone and blasted ring by ring into a stope for excavation. A mass stope blast may involve blasting rock from multi-level drift rounds and displacing the muck to specific locations in order to allow safe and easy access for ore removal. This paper presents a strategic mass stope blast that took place at a large lead and zinc underground mine in eastern Canada. The blast consisted of more than 800 holes drilled in six blocks from three different sublevels. The challenge lay in the control of ground vibration and muck movement using precise timing to complete the blasting within 6.5 seconds. During this time span, sufficient voids were created in each level to allow the muck to move from the upper to the lower levels in sequential order across the six mining blocks without bridging. This paper describes stope blast simulations using a discrete element computer code for modeling blast-induced rock displacement as well as the application of electronic detonators. These detonators provided the means to accomplish the desired firing sequence including a drop raise blast at the start of the mass blast. The modelling concept is also described in the paper.

Jan 1, 2005