Search Documents

By Thomas L. Kesler

IF all of the 14 million tons of kaolin produced in Georgia through 1949 had been mined from a single deposit 20 ft thick, it would represent a mined-out area of less than 1 sq mile. This measure of depletion is in such strong contrast with the large size of the area shown in Fig. 1, from which most of the output has come, that there has developed an optimistic outlook concerning future supplies of kaolin equal in grade to that already mined. Dozens of mines are widely but not evenly distributed within this area, which consists mostly of parts of Twiggs, Wilkinson, and Washington counties. There are scarcely half a dozen kaolin mines elsewhere in the state that have been appreciably productive, although the areas in which they occur may have good possibilities. Most of the efforts to find new deposits, therefore, will be confined to the area shown in Fig. 1, for it is here that the industry has established its facilities, and prospecting is encouraged by relatively numerous outcrops and opened deposits of kaolin.

Jan 10, 1951

By F. G. BREYER

ZINC metallurgists continue to follow with keen interest reports of successful results from the continuous retort plants at Palmerton, Pa., and Meadowbrook. W. Va. The new process had already demonstrated its ability to reduce the lead content of the metal and to effect savings in labor and fuel. The past year has shown that the retorts themselves can he built to last long enough so that the retort cost per ton of metal is lower than in past practice with small horizontal re- torts. A number of the latest type of retorts are reported to have been in continuous operation for over 18 months without a failure and are said to be still in good condition. This seems a complete answer to the last question which remained before continuous zinc smelting could he pronounced commercially practicable.

Jan 1, 1932

By E. H. Rennhack

Phase equilibria of the zinc-rich portion of the Zn-Fe-A1 system containing up to 20.0 wt pct Fe and Al have been investigated at 600°C (1112°F), 450°C (842°F), and room temperature by metallographic and X-ray diffraction techniques. The phase relationships were found to involve only those phases present in the three binary systems. THE presence of small quantities of aluminum (approx. 0.2 wt pct*) in zinc galvanizing baths is known to suppress the formation of Zn-Fe alloy layers within the coating.' As part of an extended investigation of this suppression effect and the alloy reactions involved, the zinc-rich corner of the Zn-Fe-A1 equilibrium system containing up to 20.0 pct Fe and Al was determined at 600°C (1112°F), 450° F (842° F), and room temperature. The present paper reports the findings of this study. The constitution of the Zn-Fe system has been reported by Raynor2 based mainly on the work of Schramm3-3 and Truesdale et a1.6 The solid solubility of iron in zinc is extremely small and lies between 0.0009 and 0.0028 pct in the range 150° to 400°C (302°to752°F). Within the temperature and composition range of interest, a eutectic reaction involving nearly pure zinc, liquid = Zn+FeZn13, is observed at about 419°C (786° F) and 0.018 pct Fe along with a peritectic reaction, FeZn7+ liquid e FeZn13, at 530°C (986° F) and 6.2 pct Fe. The latter reaction is sluggish due to the large proportipn of solid phase involved in the transformation. Halla et al.,7 identified the compound FeZn13 as monoclinic with a = 13.68, b = 7.63, c = 5.07, and B = 128°44'. The structure of FeZn7 was reported by Bablik, et al.,8 to be of hexagonal symmetry, belonging to either the C6v = C6/m mc or D46h = C6/mc space group. Divensions of the unit cell are a = 12.81A and c = 57.6a. The Zn-A1 diagram as composed by Raynor9 and later Gebhardt10 is characterized by a eutectic decomposition, liquid 382°C (720°F) and 95.0 pct Zn and a eutectoid decomposition, at 275° (527°F) and 78.0 pct Zn. The eutectoid reaction cannot be suppressed permanently by quenching. Above 275° (527° F), a and a' co-exist in a closed miscibility gap between 31.6 and 78.0 pct Zn. Both phases are fcc and have nearly the same lattice parameter. The maximum solubility of aluminum in zinc (B) is approximately 1.0 pct at the eutectic temperature. PROCEDURE Materials. The experimental alloys were prepared from both massive and powdered material. Cast alloys were composed from three zinc-base master alloys containing 8.0 pct Fe, 16.0 pct Fe, and 50.0 pct Al which were made from C.P. zinc, Armco iron, and

Jan 1, 1962

By J. Gross

G. H. Clevenger, Chairman of the Milling Methods Committee of the Institute, made the following introductory remarks: "Several years ago, a number of us felt that the time was ripe for a fundamental investigation of crushing and grinding. At the outset, it appeared that the first thing we needed was a yardstick whereby grinding efficiency could be measured. "The U. S. Bureau of Mines has been most generous in cooperating with the Milling Methods Committee in getting this work well under way. John Gross, who served the committee for a year as secretary, was placed in charge of the investigation and has been ably assisted by S. R. Zimmerley. "Messrs. Gross and Zimmerley will now present the Progress Report covering their work to date." PROGRESS REPORT J. Gross, Salt Lake City, Utah. -This has not been a simple problem, and when I tell you that we can give you a verbal report of what we have done during three years in five or ten minutes you will realize that we have necessarily done a great deal of work that does not appear in the final results. We have been in a virtually new field. Therefore, we have had to feel our way at each step so as to be fairly sure we were correct. The first thing that was realized in this problem was that unless we had some method of measuring what happened when we crushed an ore, we might as well quit and not go further. We realized that if we tried to measure the results of crushing or grinding by the ordinary sizing test we would not get anywhere. We could sieve down to say 200 mesh fairly accurately; we could even go one sieve size further with a little less accuracy, and then we were absolutely lost, unless we went into microscopic measurement. Even this latter method would not have been satisfactory. The question was: what were we going to measure? If we were going to measure size, we might measure one particular dimension of a particle and be off 200 per cent. or more. If we tried to measure surface, we would have something tangible; the surface of a particle, no matter how irregular, is something definite, far more definite than any linear dimension would be. Moreover, if we could measure surface, we would immediately have a method of checking the Rittinger law as to whether it was or was not correct. So the first thing that we sought was a method whereby we could measure surface on crushed particles or, we will say, on particles; it would not make any difference whether crushed or not. It then became a question of what kind of particles we were going to use in obtaining a method for surface measurement. We realized that it would be rather a com-

Jan 1, 1928

By HARRY H. SMITH

IT IS my understanding that, speaking broadly, the function of the engineering profession is to find how to do the thing required better for less money. Mechanical engineers, mining engineers, and the various other kinds of engineers are engaged in discovering and effectuating new and improved methods .of producing better goods and services at less cost to industry. The savings and advantages, thus, accruing ace reflected from time' to time in increased productive powers of industry and lower costs to the public which consumes the goods and services.

Jan 1, 1931

By C. Y. Clayton, Francis B. Foley, Muir L. Frey

DuRing the past year, we have investigated the cause of 88 per cent, of the failures by breakage near the bit end of some 1-in. hollow, hexagon, drill steel used in a metal mine. This breakage in the region of the bit end of the steel was peculiarly interesting because we have been Ied to believe that breakage is most prevalent at the shank end of drill steels near the place where the steel is gripped in the chuck of the machine. Records from the mine showed, also, that the breakage was much more frequent in the short lengths of large gage than in the longer steels; this is shown graphically in Fig. 1. Because the shorter lengths of steels are usually those that have been made from broken pieces of long steels or from steels that have worn down in service, rarely being made from new stock, those who are wont to suspect steel of tiring and crystallizing in its old age through fatigue are quite apt to see in this instance an argument in favor of their idea. As usual, a careful examination of these steels reveals defects of a character hardly to be overlooked in favor of such a cause. The steel in question was rolled with a sand core and was of the usual drill steel composition: Carbon 0.85 per cent., manganese 0.60 per cent., silicon 0.25 per cent., phosphorus 0.02 per cent., and sulfur 0.02 per cent., with the exception that in some specimens there was vanadium, not exceeding 0.20 per cent. The following lengths and gages were used: LenGth, GaGe, LenGth. GaGe, Feet Inches feet Inches Starter 2 % 7 111/16 3 2 % 8 11 4 2 % 9 1 9/16 5 2 10 1 7/16 ________6_____________115/16____________________________

Jan 1, 1924

By HUNTINGTON ADANS

(Wilkes-Barre Meeting, June, 1911.) THE arrangement of a flow of cyanide-pulp through Pachuca tanks in agitation, so as to permit a continuous process, instead of alternate filling, agitation, and emptying, has been proposed by various writers within the last two years, and more particularly by A. T. Grothe, agent for the Brown patents on Pachuca tanks in Mexico. It was first put into practice, I believe, by M. H. Kuryla at the Esperanza mine in El Oro, Mexico. The starting of agitation in Pachuca tanks after filling may offer no serious difficulties with ores which do not settle rapidly in such tall tanks; and the adaptation of the tanks to continuous agitation under such conditions may give simply a somewhat more convenient method of treatment and greater agitation-capacity for a given number of tanks, because of the saving -of time lost in filling and discharging. But in the treatment .of pulp which tends to settle rapidly, as in the cyaniding of concentrates or of the whole pulp of ores containing heavy sulphides, the packing of the slime at the bottom may, cause much trouble. The use of the radial air-pipe attachments near the top of the cone and of the air-valve outside of the air-lift .tube at the bottom may obviate the difficulty to some extent; but the action of the radial air-pipes on the cone-sides is that -of a sand-blast, and their continuous use cuts through the tanks. Moreover, even when these pipes are used, some pulps will pack tightly below them in the cones. Under such conditions the use of Pachuca tanks with intermittent filling and discharging becomes a troublesome process. Time is lost in ,starting agitation; large quantities of compressed air are wasted; pulp is blown over the tank-tops; and not infrequently it may be necessary to dig out the bottoms of tanks by hand. This trouble is the only important one occurring in the use of Pachuca tanks; and, since it is caused by intermittent filling, the .arrangement of a continuous flow of pulp from tank to tank,

Aug 1, 1911

By L. L. Swift

.It the present time there are four base metals being used for automo-tive bearing alloys. Of course there are numerous variations in the amounts of alloying elements added to each base metal and nearly all of these alloys have the conventional, if not classical, duplex structure; that is, they are composed of a hard constituent embedded in a soft matrix. The well-known theory is that the former will wear well, while the latter will be plastic enough to allow the bearing to be broken in and conform to the contours of the shaft. The requirements of the modern bearing have been most aptly described by W. M. Corse: In order to meet the engineering demands of today a good bearing metal must be able to carry the weight of the shaft and stand up under steady or suddenly applied loads, or even blows ill sorne types of service. A certain amount of plasticity is desired to compensate for minute irregularities in the shaft or bearing surface, and to permit yielding, thereby avoiding dangerous stresses in bearing and shaft and pre-venting overheating and rapid wear of parts. Less plasticity is required in a bearing tuetal if the surfaces of bearings and journals are machined accurately, aligned, and kept in alignment. It is desirable, of course, that a bearing metal have a low coeffi-cicnt of friction. Under most operating conditions the friction depends on the unit, pressure of the bcaring, the speed, the temperature, and the properties of the lubricant. A good bearing metal must have a low rate of wear to reduce the necessity for frequent replacements, and adjustment of the bearings. It must wear more rapidly, however, than the journal or shaft running on it, because replacement of the journal or shaft is more difficult and costly than replacement of the bearing.' The hardness of the bearing alloy is a property closely related to several of the foregoing. With a duplex microstructure, the measurement of hardness with any of the usual commercial devices means little. The Bierbaum method of measuring the hardness of the individual canstituents was developed to fill this need. MICROCHARACTER The Bierbaum MicroCharacter~,~ measures the scratch-hardness of a solid by pulling a weighted diamond point over the surface. The diamond point is ground so that it is the corner of a cube, and Mounted

Jan 1, 1939

By L. L. Swift

.It the present time there are four base metals being used for automo-tive bearing alloys. Of course there are numerous variations in the amounts of alloying elements added to each base metal and nearly all of these alloys have the conventional, if not classical, duplex structure; that is, they are composed of a hard constituent embedded in a soft matrix. The well-known theory is that the former will wear well, while the latter will be plastic enough to allow the bearing to be broken in and conform to the contours of the shaft. The requirements of the modern bearing have been most aptly described by W. M. Corse: In order to meet the engineering demands of today a good bearing metal must be able to carry the weight of the shaft and stand up under steady or suddenly applied loads, or even blows ill sorne types of service. A certain amount of plasticity is desired to compensate for minute irregularities in the shaft or bearing surface, and to permit yielding, thereby avoiding dangerous stresses in bearing and shaft and pre-venting overheating and rapid wear of parts. Less plasticity is required in a bearing tuetal if the surfaces of bearings and journals are machined accurately, aligned, and kept in alignment. It is desirable, of course, that a bearing metal have a low coeffi-cicnt of friction. Under most operating conditions the friction depends on the unit, pressure of the bcaring, the speed, the temperature, and the properties of the lubricant. A good bearing metal must have a low rate of wear to reduce the necessity for frequent replacements, and adjustment of the bearings. It must wear more rapidly, however, than the journal or shaft running on it, because replacement of the journal or shaft is more difficult and costly than replacement of the bearing.' The hardness of the bearing alloy is a property closely related to several of the foregoing. With a duplex microstructure, the measurement of hardness with any of the usual commercial devices means little. The Bierbaum method of measuring the hardness of the individual canstituents was developed to fill this need. MICROCHARACTER The Bierbaum MicroCharacter~,~ measures the scratch-hardness of a solid by pulling a weighted diamond point over the surface. The diamond point is ground so that it is the corner of a cube, and Mounted

Jan 1, 1939

By Fred D. DeVaney and

The coercimeter, as its name implies, is an instrument for measuring the coercive forcet of magnetic substances. It was developed by Davis and Hartenheim in the Special Studies Section, Metallurgical Division. A detailed description of this apparatus may be found elsewhere.2 The coercive force determinations of magnetic materials are interesting because of the relationship established by Gottschalk,4 who showed a linear relationship between the magnetization coercive force and the specific surface of comminuted particles. The value of this relationship in determining grinding efficiency has been shown by Dean.3 The determination of the surface contained in the subsieve sizes has always been a difficult problem for investigators. They made approximate measurements of the surface of coarse materials by sizing on screens, but for the determination of the surface of the sub-sieve sizes it was necessary to make detailed grain counts or elutriation tests, or to study dissolution rates. The technical literature contains many references to other methods for determining these surfaces, either by some special apparatus or by mathematical calculations based on distribution lines. Many of the methods are long and tedious, and the results of some, at least, are questionable. he turbidimeter gives quick results on ground cement. By using magnetite as the material to be ground, a simple determination of its coercive force by the coercimeter, requiring 10 minutes or less, can be transposed directly and accurately into units of relative surface. This subject has been pursued further by the U. S. Bureau of Mines in cooperation with the Missouri School of Mines and Metallurgy, Rolla, Mo., and the following is a description of the results.

Jan 1, 1939

By Fred D. DeVaney and

The coercimeter, as its name implies, is an instrument for measuring the coercive forcet of magnetic substances. It was developed by Davis and Hartenheim in the Special Studies Section, Metallurgical Division. A detailed description of this apparatus may be found elsewhere.2 The coercive force determinations of magnetic materials are interesting because of the relationship established by Gottschalk,4 who showed a linear relationship between the magnetization coercive force and the specific surface of comminuted particles. The value of this relationship in determining grinding efficiency has been shown by Dean.3 The determination of the surface contained in the subsieve sizes has always been a difficult problem for investigators. They made approximate measurements of the surface of coarse materials by sizing on screens, but for the determination of the surface of the sub-sieve sizes it was necessary to make detailed grain counts or elutriation tests, or to study dissolution rates. The technical literature contains many references to other methods for determining these surfaces, either by some special apparatus or by mathematical calculations based on distribution lines. Many of the methods are long and tedious, and the results of some, at least, are questionable. he turbidimeter gives quick results on ground cement. By using magnetite as the material to be ground, a simple determination of its coercive force by the coercimeter, requiring 10 minutes or less, can be transposed directly and accurately into units of relative surface. This subject has been pursued further by the U. S. Bureau of Mines in cooperation with the Missouri School of Mines and Metallurgy, Rolla, Mo., and the following is a description of the results.

Jan 1, 1939

By Arthur C. Simmons

In common with all other producing areas of the United States, Pennsylvania enjoyed increased activity and prosperity during 1937 (Table I). Prices of crude oil were better than for any year since 1930, and the Bradford average was $2.599, compared with an average price of $2.60 in 1930. Production and drilling activities were increased over 1936, although drilling for oil represented almost entirely a program of secondary development in both the water-flood areas and the air-gas repressuring areas. Bradford Oil Field The Bradford oil field continued to produce the major portion of Pennsylvania oil; however, no changes occurred in oil-production methods during 1937. Practically all of the production in the Bradford field is by water-flooding and the total number of oil and water wells completed within the area increased from 3205 in 1936 to 4112 in 1937; an increase of approximately one-third over 1936 completions. The percentage of water wells is approximately one-half of the total completions, although any specific five-spot development will have a proportion of 55 to 60 per cent water wells and 40 to 45 per cent oil wells. Offsetti~ig and boundary oil wells probably will result in a division or percentage of 50 per cent oil and 50 per cent water wells. The quoted figures for well completions include the entire Bradford field, approximately 12 per cent of which is in Cattaraugus County, New York. It is possible to make a segregation of production, but it is not possible to segregate well completions. Production in the Pennsylvania end of the Bradford field in 1937 totaled 15,076,000 bbl., or a daily average of 41,300 bbl. compared with a daily average of 37,000 hbl. in 1936.

Jan 1, 1938

By Walter Showak

The published phase diagrams for the copper-zirconium system1,2 indicate that the solid solubility of zirconium in copper is not accurately known. Studies made on relatively impure alloys by Pogodin, Shumova, and Kugucheva3 yielded a maximum solubility value of 1 wt pct Zr at the eutectic temperature. Allibone and sykes5 reported that an as-cast 0.2 wt pct Zr alloy is single phase at room temperature. Limited results obtained by Raub and Enge14 indicated that zirconium solubility in copper is less than 0.13 wt pct Zr at 940°C. Tn 1960, on the basis of a microstructural examination of several copper-rich Cu-Zr alloys, saarivirta6 placed the maximum solubility of zirconium in copper at 0.15 wt pct at the eutectic temperature, 980°C. The present note describes results obtained during a re-investigation of the Cu-Zr system for the purpose of accurately establishing the solidus and solvus curves and the eutectic temperature in copper-rich alloys. High-purity copper (99.99 pet) and zirconium (99.64 pet) consolidated reactor grade sponge were used to prepare several alloys, containing up to 2 wt pct Zr, by induction melting in graphite crucibles in vacuum and chill casting into a split steel mold. The melting procedure consisted of first melting the copper charge and then adding the bulk zirconium wrapped in pure copper foil. Chemical analyses were made of both the cold-rolled alloy ingots after homogenization at 925°C for 450 hr in evacuated quartz capsules and of small specimens which had been used in the phase diagram studies. 'The carbon content of each alloy was also determined and was found to be less than 0.001 wt pct in every case. Metallographic and electrical resistivity measurements were used as the primary methods for this investigation, although some thermal analysis studies were also performed. Heat treatments of all the alloys were carried out with the specimens wrapped in molybdenum or alloy foil (of the same composition as the specimen) and sealed in quartz tubes either in vacuum or under a purified helium atmosphere. Following high-temperature anneals for long periods of time, slight depletion of zirconium from the specimen surface was observed. Therefore, careful preparation of samples for microscopic examination and chemical analysis of the samples themselves was necessary to check the composition of samples used in determining phase boundaries. Points on the solvus curve were determined on quenched specimens by both isothermal reaction after solution heat treatment at 950°C for 8 hr and by isothermal annealing of alloy specimens at successively higher temperatures for times ranging from 24 to 500 hr. Liquation studies for positioning of the solidus and eutectic temperatures were performed by holding a pre-

Jan 1, 1962

By C. M. Romanowitz, H. A. Sawin

PLACER dredging as we know it today, especially gold dredging, is an industry about 40 years old, dating from the beginning of this century, when a few mining men in California saw the possibilities in adapting earlier dredging methods to California placer fields in and immediately adjacent to streams. At first it was thought that dredges must be operated in existing stream beds, but experience soon pointed the way to dredging alluvial deposits of old stream beds, operating on landlocked dredging ponds. Within the first five or six years of modern dredging, experience was gained so rapidly that dredges to dig 60 ft. below water level were designed and built. This depth was believed by many operators to be the maximum at which successful dredging could be carried on. Alluvial deposits of gold, suitable for dredging, were readily handled by equipment available and developed early in the industry's history. Much of the gravel was easily dug and if deposits were cemented, contained large boulders, or for some other reason could not be handled by a dredge, the ground was abandoned in favor of other deposits that could be handled easily. Many failures, adversely affecting the dredging industry, resulted from attempts at that time to extend the scope of placer dredging with equipment not suited to the formation being dredged. Dredging ground suited to early equipment was exhausted eventually, but many supposedly undredgeable alluvial fields containing gold in commercial quantities were found and became known to dredgemen. Improved equipment was needed to work deposits known to exist at great depths or associated with unusual obstructions. Operating companies looked to dredge manufacturers and metallurgists, particularly manganese-steel foundries, for improved designs and materials. Experience developed in California has spread throughout the world, and dredges of improved types have been adapted to the mining of platinum and tin as well as gold. Space will not permit a description of all the improvements in dredging since the early days, but a few of the recent developments are worthy of note, because they make possible the dredging of placer deposits of great depth, those having hard, irregular bedrock or containing large boulders in great quantities, and compacted or cemented gravel deposits. DEEP DREDGING At Hammonton, Calif., Yuba Consolidated Gold Fields has, within the past two years, built its dredge No. 20. The company has operated continuously in that field since 1904, digging successively at maximum depths of 60 ft., 80 ft., 112 ft., and now 124 ft. below water level. The first dredges were equipped with buckets of 6 and 7 1/2-cu. ft. capacity; six dredges operating in the field today have 18-cu. ft. buckets, digging now 65 to 124 ft. below water level. Some ground near Hammonton has been dug for the third time, owing to the devel-

Jan 1, 1941

By B. L. Sackett

LEAD smelting has been an important industry in Utah for many years. The first lead smelting was done, over 60 years ago, at the Rollins mine in Beaver County, by burning heaps consisting of alternate layers of wood and high-grade carbonate ore. The lead thus obtained was. molded into bullets. With the development of. the mines, the problem of cheaper handling of the ore became important. The only outlet for this ore was Swansea or the Atlantic Coast but to ship to either cost $150 per ton or more for treatment and handling. From 1864 to 1871, experimenting was done with blast, Scotch hearth, and reverberatory furnaces, with the blast furnace surviving as, the standard plant. The first crude furnaces were circular or hexagonal in shape, and were made of adobe and stone, which quickly burned out. They were small, about 2 1/2 ft. in diameter, and smelted from 3 to 10 tons. in 24 hr. The metal had to be tapped from the bottom of the crucible, necessitating a shut down of the furnace during this process. This pro¬cedure caused salamanders to form around the tap hole when the furnace was started again, which frequently resulted in freezing. The campaign lasted until a tap of bullion was made. The first successful plant of the crude stone type was operated in 1870. From 1870 to 1872, there was a smelter building craze in the state. During that period, about 20 furnaces were built, chiefly near the mines, and their operation was limited and sporadic. The work was then placed in the hands of trained metallurgists, who standardized on the rectangular form of furnace. In 1871, Daggett, at the Winnamuck mine in Bingham, installed water-jackets around the smelting zone of the furnaces. These furnaces were circular; the diameter at the tuyere line was 3 ft. 6 in. and at the charge floor 5 ft. 3 in. The height from tuyere line to charge floor was 14 ft., height of tuyere line above top of crucible was 3 ft. 8 in. Fur-

Jan 8, 1925

By A. E. Blakeslee

Morphological and electrical properties of GaAs epitaxial layers are influenced not only by changes in the nominal substrate orientation but also by small amounts of misorientation from the exact crystal planes. Deviations up to 5 deg from {11IA}, {11IB}, and (100) planes were investigated. Growth rates increase progressively with angle, approximately I u per hr per deg. Size and density of growth pyramids fall off with increasing angle, but other effects that are deleterious to the surface may occur which are heightened by increased misorientation. Carrier concentration decreases and electron mobility consequently increases as the angular offset increases, except in the case of strong compensation, where the mobility trend is reversed. It has long been known that changes in the crystallo-graphic orientation of the substrate may cause pronounced effects on the morphological properties of vapor grown semiconductor films. Reports of orienta-tion-dependent growth rates and surface characteristics are as old as the literature on epitaxy itself. shawl has recently published a comprehensive study of the dependence of growth rate on substrate temperature and orientation in epitaxial GaAs. It is also well-known that misorienting the substrate surface a few degrees away from the nominal low-index crystal-lographic plane often produces a much smoother epitaxial surface. This was reported by Tung2 for silicon, Reisman and Berkenblit3 for germanium, and by Kontrimas and Blakeslee4 for GaAs, and use is commonly made of this fact in the semiconductor industry to help guarantee smooth vapor deposits. The effects of substrate orientation on the carrier concentration and mobility of vapor grown GaAs were first documented by williams5 in 1964 and have been observed by several other authors since then,6,7 but no one has yet reported a careful study of how small changes influence these properties. We have made such a study and have found that sizable differences in growth rate, morphology, carrier concentration, and mobility can indeed be observed for epitaxial films grown on substrates that are oriented by progressive small increments away from the exact crystal plane. EXPERIMENTAL Early in the investigation an arsine synthesis system of conventional design8 was employed to produce growths on {111A}-oriented GaAs substrate crystals. In that early work, pronounced effects on carrier concentration and electron mobility were observed as a function of slight misorientation from this low index plane. That observation led to the more careful study that is reported here. An AsC13 system, differing in major aspect from those commonly in use today9 only in that the reactor is vertical rather than horizontal, was used for the detailed study. The gallium source was at 900°C and the substrates were at 750°C. The flow rate of pal-ladium-diffused H2 through the AsCl3 bubbler was 200 cu cm per min, and the flow rate of bypass H2 was also 200 cu cm per min. The substrates consisted of chro-mium-doped semiinsulating GaAs to facilitate elec-trical evaluation of the overgrowth by means of Hall and conductivity measurements on conventional eight-legged Hall bridges. They were misoriented by 0 to 5 deg from the {111A}, {111B}, and (100) planes, toward the (100) from the {111A} and {111B} and randomly toward the <111A> or <111B> from the {loo). The crystals were oriented for sawing by the Laue back-re-flection technique, which is good only to about ±1/2 deg; but after polishing or sometimes after epitaxial growth the wafers were checked by a diffractometer technique which is accurate to about * 0.1 deg. After lapping, the wafers were polished with NaOCl after the technique of Reisman and Rohr,10 and just before use they were cleaned in NaOC1, thoroughly rinsed with de-ionized water, and blown dry with nitrogen. Each run employed four wafers, each misoriented by differing amounts from one of the three major faces, and at least two runs were made for each orientation. The runs were continued long enough to provide at least a 15-µ or thicker layer. SURFACE MORPHOLOGY The appearance of all the films that were grown in a given run always changed from wafer to wafer as a function of increasing misorientation, but not always in the same regular fashion. At least three different trends were observed. These are more easily seen than described, and reference to the series of photo-

Jan 1, 1970

By H. J. Ramey

A general solution is presented for the transient temperature distribution caused by radial movement of a cylindrical heat source through a homogeneous medium of infinite extent. This problem represents a highly simplified model of the movement of a combustion front during the thermal recovery of oil. Numerical solutions are presented for a heat source moving at a constant velocity, and a velocity inversely proportional to the radial location of the heat source. Numerical solutions are presented for both finite and infinite vertical thickness of the heat source, i.e., with and without vertical heat losses. The numerical solutions are used to estimate the fuel concentration needed to maintain a combustion front during the thermal recovery of oil. The sensible heat carried to the combustion front by the injected gas stream is discussed in regard to the fuel concentration. Numerical solutions for a heat source (combustion front) of finite vertical thickness indicate the field conditions that may be necessary to sustain the temperature of a combustion front above the ignition temperature of the fuel over considerable distances from an injection well. The results also have implications in regard to the quantity of heat required during ignition. The results of this computation apply to a highly idealized model of a thermal recovery process. But the results may be used as a guide in engineering consideration of the thermal recovery process. INTRODUCTIO N The thermal recovery of crude oil has received considerable attention since the publication by Kuhn and Kochl of laboratory and field tests of this method of oil recovery. Other publications2,3,4,5,6, since that time have dealt with various features of the thermal recovery of oil and have illustrated the extremely complex nature of this process. Vogel and Krueger7 described an electric analog computer designed to solve a moving heat source problem which was analogous to movement of a combustion front during the thermal recovery of oil. The heat source was maintained at constant temperature and was a cylindrical source of infinite height (no vertical heat loss) moving radially at either constant velocity, or at a velocity inversely proportional to the radial location of the heat source. Jenkins and Ramey2 presented analytical solutions to a similar heat conduction problem and pointed out the possible importance of vertical heat losses. The following presents a general solution to the transient heat conduction problem introduced by Jenkins and Ramey4 as well as numerical solutions for a wide range of conditions possibly similar to those that might exist during field operation of the analogous thermal recovery process. DESCRIPTION OF PROBLEM The problem considered in this paper is determination of transient temperature distribution caused by a cylindrical heat source of infinite or finite vertical height, moving radially through an isotropic medium of infinite extent. It is further assumed that the heat flux generated at the surface of the moving heat source may be a function of time such that the fuel concentration required may be constant, or permitted to vary, and that heat is generated at the surface of the heat source only. In regard to the thermal recovery of oil the assumption that heat is generated at the surface of the front is equivalent to assuming that the thickness of the combustion zone is infinitely small, or that the reaction rate between fuel and oxidant gas is infinite. The last assumption does not appear stringent. See laboratory information published by Martin, et al3 Under these assumptions the temperature distribution throughout an infinite medium caused by a heat source moving radially with an arbitrary velocity may be described by The heat generation function or heat flux at the surface of the source, +(t), is Note that the fuel concentration may be defined as a function of time. Eq. 1 is derived in the Appendix.

By Stanley J. LeFond, Langtry E. Lynd

Elemental titanium has become famous as a space age metal, because of its high strength/ weight ratio and resistance to corrosion. However, the major use is in the form of titanium dioxide pigment, which because of its whiteness, high refractive index, and resulting light-scattering ability, is unequaled for whitening paints, paper, rubber, plastics, and other materials. A relatively minor use is in welding rod coatings, in the form of the mineral, rutile. United States consumption of titanium dioxide for these applications in 1973 was as follows: pigments, 891,000 st; titanium metal, 40,000 st (=24,000 st metal) ; and welding rod coatings, 10,000 st. The only commercially important titanium ore minerals at the present time are ilmenite, and its alteration products, and rutile. Titanium was discovered by Gregor in 1790, as a white oxide which he recovered from menaccanite, a variety of ilmenite occurring as a black sand near Falmouth, Cornwall. Barksdale (1966) states that the fundamental chemical reactions on which the present day titanium industry is based were known before 1800, although it was not until 1918 that these pigments were available commercially on the American market. Pings (1972) outlines the early history of the titanium industry in the United States, referring to the work of Guise (1964) and others: "Mining of titanium minerals in the United States began sometime between 1880 and 1900, in Chester County, Pennsylvania. Small quantities of rutile were also produced during the time in North Carolina and Georgia. In 1901 rutile was mined from a deposit near Roseland, Va., and was used in making titanium chemicals and for coloring ceramics. Ilmenite in the deposit was produced as a separate item in 1913, and rutile and ilmenite were obtained from this deposit through 1921. The mining of titanium bearing beach sands began in 1916 near Mineral City and Pablo Beach, Fla., for the purpose of making titanium tetrachloride to be used in tracer bullets, flares, and smokescreens. The titanium pigment industry was founded in 1918. By 1928 a large part of the domestic production of rutile, ilmenite, and zircon came from Florida. However production ceased in 1929 in Florida with the mining of newly discovered deposits in Virginia which were mined until 1968. The discovery of new deposits in Florida, and the development of better mining and concentrating methods for lowgrade sands, led to a return of activities in this area. The large deposits near Tahawus, N.Y., were brought into production in 1942 by National Lead Co. (now N L Industries Inc.), and by 1949 this company was the lead¬ing producer of ilmenite in the world. In 1948 the extensive deposits of ilmenite and ilmenite-bearing iron ores were discovered in eastern Quebec." The beginning of the modern titanium metal industry was in 1948, when E. I. du Pont de Nemours & Co. produced the first metal. U.S. Bureau of Mines reports, which gave details of the Kroll process, together with the attractive properties of the metal for

Jan 1, 1975

By B. G. Matson, M. A. Whitfield, G. R. Dysart

This paper describes the development of u computer program to calculate changes that occur in the length of tubular goods due to temperature and pressure changes during stimulation operations. Due to the numerous variables involved and the uncertainty of all static and dynamic conditions that could exist, it becomes a staggering task for individuals charged with completions to perform the necessary mathematical calculations. The computer program permits advance calculations for several sets of conditions. INTRODUCTION In the Delaware basin of West Texas alone, 50 wells were contracted or drilled to 15,000 ft or deeper in 1965. Deep well activity is continuing in this and other areas on an expanding scale. Many of these deep wells require extensive stimulation for successful commercial production, and during these operations, pressures and temperatures are encountered that have a pronounced effect on the length of tubular goods. This length change during a large-volume, high-pressure stimulation treatment utilizing fluids considerably cooler than bottom-hole temperature can be of such a magnitude that permanent damage to casing and tubing will result unless mechanical design, pressures and fluid temperatures are evaluated and controlled. These pressure and temperature effects can be calculated. However, the process lends itself well to computer solutions because of the mathematical nature of the problem and the calculating hours involved in arriving at an answer. The engineering-hour demand becomes more severe as tapered strings are involved. On initial treatments on a given well, surface pressure and injection rate conditions are unknown, and offset well conditions have not proven to be a reliable method for making predictions. For these reasons, it has become rather standard procedure for operators to compensate for these uncertainties by placing unnecessary pressure and fluid temperature restrictions on stimulation design. On a number of occasions treating fluids have been preheated to as much as 160F as a means of compensating for thermal contmction resulting from pumping cool fluids. The maintenance of packer seals has been treated by Lubinski, Althouse and Logan&apos;,&apos; and the problem of therma1 effects on pipe has been explored by Ramey." These works were expanded and the results made applicable to everyday oilfield terminology before submitting them to computer programming. The pressure and temperature effects on tubing movement previously mentioned occur simultaneously as fluid moves through the pipe. The pressure changes, for purposes of explanation, are categorized here as to the various effects these pressures have on a tubing string. These divisions are (1) the piston-like results of forces acting on horizontal surfaces exposed to pressure, (2) swelling or ballooning of the tubing along its entire length due to the forces of pressure acting against the tubing walls, (3) the elongation of tubing due to frictional drag and (4) corkscrewing of the pipe due to internal pressure. Thermal changes are also of great importance, as their results may be more significant than any of the pressure effects. Steel is an excellent conductor of heat and the earth is a relatively poor conductor. It has been calculated that pipe temperatures at depths of more than 20,000 ft approach within as little as 25" the temperfature of the surface fluid after pumping for 2 hours, or a drop in temperature in some treatments of more than 220F. The equations presented in this paper were developed for computer programming and simplicity of input information; therefore, numerical constants such as Young&apos;s modulus for steel (28 X 10\ si), the coefficient of thermal expansion of steel (6.9 X 10."IF) and Poisson&apos;s ratio for steel (0.3) are included with unit conversion factors. The moment of inertia of tubing cross-sectional area with respect to its diameter was changed to a constant times (D&apos; — d&apos;) where D is outer diameter and d is inner diameter. Units in the equations are length in feet, diameter in inches, density in pounds per gallon, pressure in psi, rate in barrels per minute and time in hours. PISTON-LIKE REACTIONS A change in tubing internal dimensions and the exposure of other horizontal surfaces to different pressures on the inside and outside of the tubing result in a reaction much like a piston under pressure. Such is the case when the internal diameter changes in a combination string of pipe, when seals of a slick joint assembly are subject to pressure and in the end effects of a tubing string. The change in tubing length due to the piston effects of a slick joint packer is affected by the various diameters involved, the tubing pressure Ap,, the casing pressure ,Ap,, length of pipe L, densities of fluid in the tubing before and during pump-

By Robert W. Thomas

LEACHING of mined-out areas at the Arizona property of the Ray Mines Division, Kennecott Copper Corp., was started on Jan. 20, 1.937, and by July 1, 1938, 10,000,000 lb. of copper had been produced by this method. Leaching operations at present are confined to the western portion of the ore body and over an area of approximately ten acres. The ore in this area was extremely high in pyrite and the copper content, which averaged slightly in excess of 1 per cent, was the result of incomplete secondary enrichment by solutions which apparently worked laterally from the main ore body. Above the ore was an unaltered zone of primary or protore averaging 125 ft. in thickness and containing approximately 0.6 per cent copper. Above this was the capping or leached zone averaging 50 ft. thick.

Jan 1, 1938