Search Documents

By Wm. Reuben Webster

Brass is an alloy of copper and zinc. The brass containing 70 per cent copper and brasses (using this term to denote all useful 30 per cent zinc. Fig. 3 shows the effect of proportions of the two constituents) are the annealing at various temperatures on the most valuable and widely employed of all same alloy. This effect is somewhat modi- nonferrous alloys, because of their high resistance to ordinary corrosive agencies and the very wide range of properties that may be imparted to them by variations in the proportions of the constituents and by variations in mechanical treatment and heat-treatment. Fig. I shows the normal physical properties, as determined by standard tensile tests, of the series when in the annealed condition. Fig. 2 shows the effect of varying amounts of cold-working on an almost pure fied by the degree of cold-working to which a brass has been subjected, as shown by Fig. 4. A fourth test, which is empirical, has been found useful because of its simplicity —the hot hammer test. Samples 1/2 in. in diameter and 3/4 in. long are placed in a suitable furnace. These are withdrawn one at a time. at successively higher temperatures and are subjected to the blow of a drop hammer weighing 50 lb. with a drop of 4 ft. The percentages of reduction in length of the cylinders are plotted against temperatures and give a camparative measure of plasticity at different temperatures. The results of this test on several

Jan 1, 1942

By Wm. Reuben Webster

Brass is an alloy of copper and zinc. The brass containing 70 per cent copper and brasses (using this term to denote all useful 30 per cent zinc. Fig. 3 shows the effect of proportions of the two constituents) are the annealing at various temperatures on the most valuable and widely employed of all same alloy. This effect is somewhat modi- nonferrous alloys, because of their high resistance to ordinary corrosive agencies and the very wide range of properties that may be imparted to them by variations in the proportions of the constituents and by variations in mechanical treatment and heat-treatment. Fig. I shows the normal physical properties, as determined by standard tensile tests, of the series when in the annealed condition. Fig. 2 shows the effect of varying amounts of cold-working on an almost pure fied by the degree of cold-working to which a brass has been subjected, as shown by Fig. 4. A fourth test, which is empirical, has been found useful because of its simplicity —the hot hammer test. Samples 1/2 in. in diameter and 3/4 in. long are placed in a suitable furnace. These are withdrawn one at a time. at successively higher temperatures and are subjected to the blow of a drop hammer weighing 50 lb. with a drop of 4 ft. The percentages of reduction in length of the cylinders are plotted against temperatures and give a camparative measure of plasticity at different temperatures. The results of this test on several

Jan 1, 1942

By E. F. Loiseau

In a paper on the manufacture of artificial fuel, read at the Philadelphia meeting of February, 1878, I enumerated the difficulties which I had to overcome before succeeding in the mixing of coal-dust and clay, the compressing of the same mixture, and the water-proofing of the lumps. The drying of the lumps, after leaving the press, was the remaining difficulty, and it mas expected that a plan devised by Dr. Charles N. Cresson, of Philadelphia, would enable us to dry the fuel as rapidly as it was moulded, and that a continuous production could in that way be obtained. The company was reorganized. The works were purchased by the new company at an assignee's sale, and the oven was modified, according to Dr. Cresson's plan. Anticipating a possible failure, I had prepared a plan by which I expected to be able to demonstrate that anthracite coal dust nixed with pitch, could be manufactured with our present machinery slightly modified ; so that after all, if we were compelled to give up the attempt to make fuel for domestic use, there was a possibility of succeeding in the manufacture of a good steam-fuel. The plan suggested by Dr. Cresson for drying the pressed lumps of coal-dust cemented with clay, did not work as well as we expected. It enabled us to dry more fuel than we did before, but it could not be made to dry more than one half of the lumps produced by the press. The plan mas abandoned, and I was authorized to experiment with coal-dust and coal-tar pitch. The cement which is used in Europe to conglomerate coal-dust is usually dry pitch, which is prepared by separating from the tar, at a temperature of 572' Fahrenheit, the volatile matters which it contains. Some manufacturers, however, employ crude tar, others, a rich tar, which has been cleared of 25 per cent. of its volatile substances, by heating it to 392' Fahrenheit. But with common tar very weak fuels are obtained, which do riot burn well, and give out a strong smell and a great deal of smoke ; it is also necessary to subject them to a baking process, in order to solidify them, and to eliminate the more volatile of the materials contained. This operation of course requires a special plant, the cost of which increases sensibly the price of manufacture, without counting the products

Jan 1, 1880

By E. F. Loiseau

IN a paper on the manufacture of artificial fuel, read at the Philadelphia meeting of February, 1878, I enumerated the difficulties which I had to overcome before succeeding in the mixing of coal-dust and clay, the compressing of the same mixture, and the water-proofing of the lumps. The drying of the lumps, after leaving the press, was the remaining difficulty, and it was expected that a plan devised by Dr. Charles M. Cresson, of Philadelphia, would enable us to dry the fuel as rapidly as it was moulded, and that a continuous production could in that way be obtained. The company was reorganized. The works were purchased by the new company at an assignee's sale, and the oven was modified, according to Dr. Cresson's plan. Anticipating a possible failure, I had prepared a plan by which I expected to be able to demonstrate that anthracite coal dust mixed with pitch, could be manufactured with our present machinery slightly modified ; so that after all, if we were compelled to give up the attempt to make fuel for domestic use, there was a possibility of succeeding in the manufacture of a good steam-fuel. The plan suggested by Dr. Cresson for drying the pressed lumps of coal-dust cemented with clay, did not work as well as we expected. It enabled us to dry more fuel than we did before, but it could not be made to dry more than one-half of the lumps produced by the press. The plan was abandoned, and I was authorized to experiment with coal-dust and coal-tar pitch. The cement which is used in Europe to conglomerate coal-dust is ,usually dry pitch, which is prepared by separating from the tar, at a temperature of 572° Fahrenheit, the volatile matters which it contains. Some manufacturers, however, employ crude tar, others, a rich tar, which has been cleared of 25 per cent. of its volatile substances, by heating it to 392° Fahrenheit. But with common tar very weak fuels are obtained, which do not burn well, and give out a strong smell and a great deal of smoke ; it is also necessary to subject them to a baking process, in order to solidify them, and to eliminate the more volatile of the materials contained. This operation of course requires a special plant, the cost of which increases sensibly the price of manufacture, without counting the products

Jan 1, 1880

By H. F. Ramstad, F. D. Richardson

The equilibria (a) SiOz +Hz =SiO +H20 and (b) Si + SiO, = 2Si0 have beet1 studied at temperatures of 1425"to 1600°C ad 1310°to 1485°C respectively. The stattdard free energy changes for the tzrro reactions are given by the equatiotts Combination of the results for both equilibria leads to tiotz removes certain anomalies in existing high-terlzperature data for equilibria involving silica and silicon in iron. In many metallurgical processes and in many laboratory investigations silicon monoxide undoubtedly plays an important role. It is unfortunate therefore that wide differences exist between the results obtained by different investigators1-7 in their studies of such equilibria as In an attempt to put our knowledge of SiO on a surer basis, an exhaustive study has been made of equilibria [I] and [2] at temperatures ranging from 1300" to 1600°C. Reaction [I] was studied by measuring the amounts of silica which could be condensed from streams of Hz or Hz + HzO which had previously been brought into equilibrium with silica at temperatures ranging from 1425" to 1600°C. Reaction [2] was studied by measuring the material that could be condensed from streams of Hz or argon which had been brought into equilibrium with mixtures of silicon and silica at temperatures ranging from 1310" to 1485°C. EXPERIMENTAL Materials. The silicon was "superpure" grade and contained less than 0.1 pct impurities. The silica was prepared from pure mineral quartz; this was crushed and treated with concentrated hydrochloric acid to remove particles of iron, washed with water, and finally dried at 120°C. For the hydrogen + silica reaction, the silica was sized to —20+100 mesh. For the silicon + silica reaction, the two materials were ground to a fine powder in an agate mortar. The hydrogen and argon were commercial oxygen-free gases. The gas streams were controlled with capillary flow meters and the volumes were measured by wet gas meters. After passing through the meters, the gases were partially dried by silica gel. The hydrogen for the HZ + SiOz reaction was then passed through palladised asbestos at 300°C and dried with magnesium perchlorate. The efficiency of oxygen removal was checked throughout the experiments by passing the gas over an electrically heated strip of nichrome, used as an indicator as described by Rathman and de itt.' When mixtures of HZ + Hz0 were required, the partial pressures of water vapor (1.8 to 22 mm) were obtained by passing the hydrogen through oxalic acid dihydrateg' lo held at various controlled temperatures, O.l°C, by means of a water bath. The hydrogen for the Si + Si02 reaction was purified by passing it over a mixture of 3 parts of magnesium to 5 of lime heated to 600°."l1 u The argon for this reaction was passed through titanium powder (-3/16 in. + 100 mesh) heated to 900°C. The nitrogen used to prevent the reaction products escaping from the condenser (see later), was deoxidized by copper or iron at 600°C. All these gases were finally dried with magnesium perchlorate. Furnace, Temperature Contr01, and Measurement A molybdenum resistance furnace was used for both sets of experiments. The reactions were conducted inside a high-grade alumina tube, 36 in. long and 1 in. in diam as indicated in Fig. 1. With this arrangement an even temperature zone (2"C) 4 cm long was satisfactorily obtained. The temperatures were kept constant by means of a proportional controller actuated by a Pt-Pt 13 pct Rh thermocouple. This was placed between the two alumina tubes, so that the temperature at the junction was 1400" to 1450°C. Up to 1485"C, the temperatures were measured with Pt-Pt 13 pct Rh thermocouples. For higher temperatures an optical pyrometer was used, this being sighted (through the glass window 1 in Fig. 1) on the end of the alumina tube, that held the SiOz or Si +SiOz mixture, 10 in Fig. 1. The optical pyrometer was recalibrated whenever a change was made in any part of the apparatus situated in the hot zone. Successive readings with the optical pyrometer were reproducible to within 1"C. Equilibrium Apparatus and Procedure. Hydvogen and Silica Reaction. The apparatus is shown in Fig.

Jan 1, 1962

By Thomas Haight Leggett

I.—The Deep-Level Shafts. The gold-deposits of the Witwatersrand (Anglice, " White Waters' Range ") are, as is well-known, more or less parallel and tilted sedimentary beds of quartz-pebble conglomerate impregnated with gold. These beds, however, are locally called "reefs"—a term equivalent in signification to the American "ledge"—and, like the latter, usually applied to lodes, though covering in practical usage all deposits of tabular form. The first developments of the reefs of the Rand were naturally made along their outcrops. Since the mining law of the Transvaal does not confer upon locators the "extralateral right," the property of each locator upon the outcrop or apex ends with the vertical planes drawn through the boundaries of the claim. Consequently those portions of the reefs which lie "on the dip," beyond these boundaries, are separately acquired by locating new surface-claims, and are usually to be mined only by means of vertical shafts, reaching the reefs at considerable depths. The term "deep-level properties " is given to such claims on the dip, and the " deep-level shafts " are the vertical shafts sunk in the hanging-wall of the Witwatersrand reefs, in contradistinction to the incline-shafts almost universally employed on the outcrop-properties. Number and Distribution.—The accompanying diagram, Plate I., shows the number and depth of these deeplevel shafts, completed or under process of sinking, up to January 1, 1900. A number of shafts already located upon new deep-level properties, but upon which no work has yet been done, are not included in this diagram.* Vertical shafts sunk upon outcrop-

Jan 1, 1901

By Arthur F. Taggart

This paper proposes two units (believed to be new) for designating, respectively, capacity and efficiency for primary and intermediate crushers. Capacity Operators know that the tonnage of rock that can be put through a particular crusher in a given time depends primarily upon the crusher setting (open setting for jaw and primary gyratory types; closed setting for cones and rolls), and secondarily on the lithological character of the feed, its maximum size, the amount of fines that it carries, its moisture content, and the method of feeding. The proposed capacity formula states a relationship between all of these factors in one empirical equation, as follows: Tr = TR80K'K" [I] in which Tr, called "reduction tons per hour" is the new capacity unit; T = tons of feed per hour requiring crushing; R80 = "80-per cent reduction ratio"; and K, K', and K" are constants that approximate quantitatively lithological character, moisture content and method of feeding, respectively. T is the hourly weight of material in the feed that is coarser than the coarsest discharge of the crusher. (For marked departures from the normal specific-gravity range—2.5 to 2.7—T should be adjusted to corresponding volumes.) In the crushers under consideration, discharge from the crushing zone is limited by the minimum dimension of a particle. Passage of the particle through a square-mesh screen is limited by its intermediate dimension. Sheppardl has shown that the ratio of maximum: intermediate: minimum average dimensions of broken rock fragments may be taken as about 1.5:=:0,6 for nonslabby rocks such as are normally crushed, while for slabby rocks, such as thin-bedded sedimentaries, foliated schists and gneisses, and the blocky metamorphics, the ratio is of the average order I.3:I:o.3, with the possibility of an even smaller relative value for the thickness. Gaudin2 finds the corresponding ratio for —I50 + 200-mesh pyrite to be I.4: I:0.6. The hourly tonnage of crusher-plant feed, therefore, should be diminished by the amount thereof that would pass a square-mesh screen of which the aperture is S times the crusher setting, where S is a shape factor with the value 1.7 for rocks that break exceptionally cubic; 2 for ores and rocks that exhibit no appreciabie tendency to slabbiness; and 2.5 to 3, or, in exceptional cases, even larger, when the tendency to slabbiness is marked. R80 is the quotient of the theoretical square-mesh aperture that would pass 80 per cent of the feed, divided by the aperture that would pass 80 per cent of the product. It is best determined from screen tests. If, as is usual with primary crushers, a sizing test of feed is not available, the

Jan 1, 1943

By Arthur F. Taggart

This paper proposes two units (believed to be new) for designating, respectively, capacity and efficiency for primary and intermediate crushers. Capacity Operators know that the tonnage of rock that can be put through a particular crusher in a given time depends primarily upon the crusher setting (open setting for jaw and primary gyratory types; closed setting for cones and rolls), and secondarily on the lithological character of the feed, its maximum size, the amount of fines that it carries, its moisture content, and the method of feeding. The proposed capacity formula states a relationship between all of these factors in one empirical equation, as follows: Tr = TR80K'K" [I] in which Tr, called "reduction tons per hour" is the new capacity unit; T = tons of feed per hour requiring crushing; R80 = "80-per cent reduction ratio"; and K, K', and K" are constants that approximate quantitatively lithological character, moisture content and method of feeding, respectively. T is the hourly weight of material in the feed that is coarser than the coarsest discharge of the crusher. (For marked departures from the normal specific-gravity range—2.5 to 2.7—T should be adjusted to corresponding volumes.) In the crushers under consideration, discharge from the crushing zone is limited by the minimum dimension of a particle. Passage of the particle through a square-mesh screen is limited by its intermediate dimension. Sheppardl has shown that the ratio of maximum: intermediate: minimum average dimensions of broken rock fragments may be taken as about 1.5:=:0,6 for nonslabby rocks such as are normally crushed, while for slabby rocks, such as thin-bedded sedimentaries, foliated schists and gneisses, and the blocky metamorphics, the ratio is of the average order I.3:I:o.3, with the possibility of an even smaller relative value for the thickness. Gaudin2 finds the corresponding ratio for —I50 + 200-mesh pyrite to be I.4: I:0.6. The hourly tonnage of crusher-plant feed, therefore, should be diminished by the amount thereof that would pass a square-mesh screen of which the aperture is S times the crusher setting, where S is a shape factor with the value 1.7 for rocks that break exceptionally cubic; 2 for ores and rocks that exhibit no appreciabie tendency to slabbiness; and 2.5 to 3, or, in exceptional cases, even larger, when the tendency to slabbiness is marked. R80 is the quotient of the theoretical square-mesh aperture that would pass 80 per cent of the feed, divided by the aperture that would pass 80 per cent of the product. It is best determined from screen tests. If, as is usual with primary crushers, a sizing test of feed is not available, the

Jan 1, 1943

By W. A. Mudge

This discussion will be limited to malleable, commercially pure nickel and some high-nickel alloys, containing more than 50 per cent of nickel, which are produced by The International Nickel Company, Inc. at its Huntington works, West Virginia, from electrolytic nickel or from a nickel-copper sulphide matte. The principal sources of nickel are sulphides of nickel, copper and iron, which are found in the large deposit of pyrrhotite-pentlandite-chalcopyrite ores in the Sudbury area of Ontario, Canada. Pentlandite, a complex nickel-iron sulphide, is the nickel carrier. These ores are concentrated, roasted, and smelted to remove considerable iron and sulphur and to produce a nickel-copper sulphide matte. Separation of the component sulphides of this matte, followed by electrolytic refining, results in the production of electrolytic nickel and electrolytic copper; direct refining of a selected portion of the matte gives the nickel-copper alloy, Monel. FUNDAMENTAL OPERATIONS Melting of the metallic materials is done in natural gas-fired, acid furnaces of the open-hearth, or reverberatory, type, having capacities of 6 to 20 tons; in three-phase, basic, electric-arc furnaces, having capacities of 7 to 20 tons; and in basic, high-frequency induction furnaces having capacities of ½ to 3 tons. Malleable, commercially pure nickel is melted in the acid open-hearth furnace. The charge is sulphur-free, electrolytic nickel, containing 99.9 per cent nickel* and clean mill scrap. Monel, containing approximately two thirds nickel and one third copper, is produced by roasting the nickel-copper sulphide matte to an oxide, smelting the oxide with charcoal in a 20-ton, acid open-hearth furnace, adding clean mill scrap, duplexing to a 20-ton, basic, electric-arc furnace, and refining in this furnace with a lime-fluorspar, carbide slag. Inconel, containing nickel, 80 per cent; chromium, 14 and iron, 6, is melted in the 7-ton electric-arc furnace or the 3-ton induction furnace. The charge is electrolytic nickel, ferrochromium and clean mill scrap. These are the fundamental operations. High-nickel alloys are produced from one of these three materials by additions of suitable amounts of manganese, aluminum, silicon or copper. For example, the age-hardenable alloy, K Monel, is produced from Monel by the addition of approximately 3 per cent of aluminum, and D nickel is produced from nickel by the addition of approximately 4.5 per cent of metallic manganese. For conversion to rods, bars, sheet, strip, tubing and wire forms, by hot-working and cold-working operations, the molten materials are teemed into ingots ranging in size from 14 by 14 by 60 in., 3300 lb., to 36 by 36 by 48 in., 18,000 lb. All ingots are overhauled mechanically before hot working.

Jan 1, 1946

By W. A. Ver Wiebe

It is becoming increasingly apparent that the State of Kansas contains one of the largest reserve areas for oil exploration in the United States. During the year 1936 no less than 54 new oil pools were discovered by drilling. In addition, seven gas pools were found, which may develop into oil pools when deeper horizons are tested. Several old pools increased their reserves when production was found in lower strata. The data presented in Table 2 indicate that nearly 2000 wells were drilled in the state during 1936. Of these more than 1214 found commercial quantities of oil and at least 61 found marketable quantities of gas. The data are conservative because complete results on drilling are not available for the eastern part of the state. Ellis, Rice and Russell Counties share honors with a total of 10 new pools in each. Barton County is prominent with six pools; while those counties claiming fewer new pools are Clark, Ellsworth, Harvey, McPherson, Ness, Pawnee, Rooks, Stafford and Trego. Important additions to our gas reserves were found in Finney and Haskell Counties, which are north of the extensive Hugoton gas area and may some day be part of it. At the close of the year there were 17,317 wells in the state rating as producers. By far the larger share (14,000) were classed as strippers and allowed to flow 100 per cent of their potential capacity, thus accounting for 33,500 bbl. a day. The remaining wells, capable of producing from 15 up to over 6000 bbl. per day, were limited in output according to these amounts. The largest wells having a potential of from 3000 to 7000 were allowed to flow from 2 to 3½ per cent of their official potential capacity. The percentage rises until wells of 15 to 20-bbl. capacity have a rating of slightly over 83. On the basis of these calculations the total potential capacity of all wells was 1,667,814 bbl., and the daily amount allowed was 175,851. Nine of the pools most recently opened were still unable to market their oil and were classified as "shut-in" pools. Total production for the state for 1936 was somewhat over 58 million barrels. Striking Geological Data Some interesting geological data were uncovered by deep drilling during the year. The most remarkable bit of information is the discovery

Jan 1, 1937

By N. C. Gay, P. J. Van Der Veever

The Klerksdorp gold mining district, South Africa, experiences a relatively high level of seismicity with many seismic events of magnitude greater than 4. These large events appear to have foci close to fault planes, most of which displace the strata by several hundred metres over a wide area. To help understand the mechanism of these large mining- associated seismic events, in situ stress measurements were made at 4 sites using "CSIR doorstopper" strain relief techniques. The sites were chosen close to, or some distance from fault planes and other structures. The results show that at all 4 sites a relatively large horizontal stress is oriented approximately north- west. The magnitude of this stress ranges from 0,78-1,O of the vertical stress. A marked horizontal stress anisotropy, varying from 13-30 MPa is also present. The dominant structural features are large, north-east striking normal faults which extend across the entire length of the goldfield. Displacements across these faults vary from a few centimetres to several hundred metres. Bedding plane faults across which large displacements may occur are also common as are north and north-west striking dykes. The majority of the faults strike at approximately 90º to the maximum horizontal stress and at all sites a large compressive stress plunges in the direction of dip of the strata and fault planes. Thus a significant shear stress may act across suitably oriented planes causing them to be in a state of potentially unstable equilibrium. This abnormal stress situation would exist along the entire length of the fault

Jan 1, 1982

By J. H. Fletcher

AIR has been cooled, heated, washed; humidified and dehumidified for many purposes and in many industries. At a number of metal mines air is conditioned to reduce the high humidity and unbearable heat found in deep workings, and at some mines air is washed to allay siliceous dust. Steam is introduced into the intake air at many coal mines, particularly in winter, for the purpose of keeping loose coal dust so moistened that the hazard of an explosion is lessened. This paper will describe a further successful application of air conditioning in a coal mine, where, for over three years, all intake air has been cooled to a constant temperature for the sole purpose of preventing roof falls.

Jan 1, 1931

By J. H. Scaff, H. C. Theurer, E. E. Schumacher

The microwave region of the radio spectrum was effectively utilized in radar designs during the recent war and it has become of increasing interest in the field of communications. Work in this field has led to an important use for silicon—that of the point contact rectifiers†1 in the frequency converter of microwave (radar or radio) receivers—and has stimulated considerable interest in the electrical properties and preparation of silicon and its alloys. Silicon is an electronic semiconductor. Its conductivity at room temperature results principally from the presence of certain impurities. While for metals an increase in impurity content increases the resistivity, for semiconductors such as silicon the opposite occurs and, in general, the addition of impurities lowers the resistivity. Silicon materials may be classified into one of two groups depending upon the manner in which the impurities contribute to electrical properties. These have been termed for convenience p-type or n-type. P-type silicon develops a very large positive thermal emf against metals, has a Hall coefficient of positive sign and a low resistance direction in point contact rectification with the silicon positive with respect to the point. N-type silicon, on the other hand, develops a negative thermal emf against metals, has a Hall coefficient of negative sign and a low resistance direction in rectification with the silicon negative with respect to the point. Impurities which produce n-type silicon are called donors inasmuch as these elements contribute to electrical conductivity by donating electrons to an unfilled energy band in the silicon. On the other hand, elements which produce p-type silicon are known as acceptors as these impurities contribute to the electrical conductivity by accepting electrons from a filled energy band permitting what is known as conductivity by "holes" in which the sign of the carriers appears to be positive. A general treatment of the mechanism of conduction in semiconductors from the viewpoint of modern band theory has been given recently by Pearson,2 by Becker, Green and Pearson,3 and by Torrey and Whitmer.4 In this investigation boron and aluminum have been found to be acceptors, and phosphorus, arsenic, and antimony to be donors in silicon. Data on the effect of boron and phosphorus on the electrical properties, when present singly and in combination, have been acquired. These data are discussed in the present paper. Raw Materials Used and Methods for Adding Seeond Constituents Silicon from two sources was used in this work and these will be referred to as A and B respectively. Silicon A is a material of high purity supplied by the Electro Metallurgical Co. It is prepared by chemical purification of "commercial" silicon obtained from the arc furnace reduction of SiO2. It contains 99.8 pct silicon, minimum, with small amounts of calcium, iron, aluminum, boron, and phosphorus as the principal impurities. This material was extensively employed in these studies as well as in the commercial preparation of rectifier materials. Silicon B is a material of high purity from the du-Pont Co. It is prepared by a pyrolytic reduction of Sicl4 and is free of analytically detectable amounts of boron and phosphorus. Its use permitted study of the effect of boron and phosphorus individually on the properties. This material contains, however, spec-troscopic traees of a number of metals, some of which affect electrical and rectification properties. Typical analyses for the two grades of silicon are given in Table 1. To make controlled additions of boron to the charge it was necessary to employ a low boron content master alloy since the quantity of boron to be added was usually only a few thousandths of one percent. The alloy containing nominally one percent boron was prepared by melting chemically pure boron with silicon A using the melting techniques for 320 g silicon

Jan 1, 1950

PRECEDING chapters on thermochemistry, and the reactions in and between metal and slag phases in the bath of the furnace tend to emphasize the equilibrium or "static" conditions in the furnace and process, such as the total amounts of heat from fuel combustion or from certain bath reactions, the concentration relationships between slag and metal at the steady state for certain reactions, and the like. Such data are obtained essentially by means of the logic of thermo- dynamics, which helps to determine the energy change between initial and final states in a process as well as to define its equilibrium or steady-state condition, but which is not concerned with the rate of change in the process or with the mechanisms or path followed between initial and final states. These questions of just "how it works" and "how fast" belong to the kinetic aspect of any process; their answers are helpful in speeding up or slowing down and thus controlling intelligently its operation, and also to understand certain natural limitations which are especially important in many high-temperature processes. The kinetic aspects of interest here comprise mainly (1) the flow of gases through the furnace system, (2) the flow of heat in the system, and (3) the mechanisms and rate factors in the various chemical reactions. A really adequate discussion of the first two subjects would require at least three or four times the space available here; it has been tried, therefore, in this and the next chapter to outline but a few fundamentals necessary to an intelligent approach and to indicate some of the conditions of heat and gas flow more or less peculiar to the open hearth, since several good general discussions on these subjects may be found in the literature.(1) For the designer of open-hearth furnaces, the principles of gas flow are of paramount importance.(2,3,4,5) They are also important to the operation of the process, however, at least to the extent of a general qualitative picture of the movement of gases in the system, which is all that is attempted here.

Jan 1, 1944

By J. L. Bray

Lead has often been suggested as a protective coating for iron and steel. Such a protective coating should possess: (1) good adhesion, (2) durability, (3) ease of application, (4) freedom from pinholes, (5) good appearance and (6) low cost, but, unfortunately, lead coatings so far produced do not have all of these characteristics. Because of the necessity of carrying out the coating process cheaply, and because lead solutions have poor plating characteristics, most of the efforts have been directed toward the hot-dipping process rather than electroplating. The hot-dipping processes using lead have not been successful chiefly because of the lack of adherence between iron and lead. In any coating process involving iron a bond can be obtained only by the formation of an intermetallic compound, the formation of a solid solution, or mechanical means. Lead forms with iron two immiscible liquid solutions, and in the solid state no intermetallic compounds or solutions. It is necessary, therefore, to employ some other element or elements as a binding agent. Tin may be used as in terneplate, or copper in the form of a thin film of electrolytically deposited metal to which the lead will adhere. Because of its physical and chemical properties, lead as a coakkg medium would undoubtedly be limited in its use to sheet and wire and then only when the article is not subject to abrasion or wear. A very large tonnage of these products is being used under such conditions and a successful lead-coating process should be a valuable contribution to the science. Two other difficulties stand in the way of successful lead coating—that of poor appearance of the weathered surface and the tendency of the lead to form pinholes during solidification. Since lead is commonly accepted as cathodic to iron, these exposed areas are ones of accelerated corrosion. Use of Zinc.—The method under consideration involves zinc as a binding agent on both the steel sheet and in the molten bath. This

Jan 1, 1937

By Hans Conrad, W. D. Robertson

FORMAL theories of yielding and flow have been developed to describe thermally activated plastic flow in metal crystals.'-" hey are all based on Becker's' original idea that thermal fluctuations aid the applied stress in overcoming internal barriers to flow and lead to the following relation. where j is the strain rate; C is a constant which includes a frequency factor, the entropy, the number of flow units, and the amount of strain associated with each successful fluctuation; E(T) is the activation energy associated with flow, and is a decreasing function of the applied stress, 7; k is Boltzmann's constant; and T is the temperature in OK. The various theories differ mainly in the model chosen and in the nature of the relationship between the applied stress and the activation energy. Beckerl and Orowan' suggest a relationship of the form E a(Ti — t)2, where .ri represents the stress required for flow without the aid of thermal fluctuations; Kauzmann,3 Cottrel1,5 and Seeger6,7 suggest E a(t — t) ; Fisher8 suggests E while Cottrell and Bilby4 suggest a more complex relationship between E and 7. Additional data are needed to test these various theories., esweciallv- in view of Dorn's9 ork. which indicates that the activation energy for creep is independent of the stress and strain. The present paper presents the stress-strain data derived from incremental loading of magnesium single crystals in tension and direct shear, in the temperature range of 78" to 364°K. Incremental loading was employed in order that the creep component of the strain could be determined. Stress-strain curves of aluminum10-13 and copper" single crvstals. derived from incremental loading tests, have been found to be in agreement with those obtained by the more conventional constant strain rate or loading rate tests. Two types of tests were conducted in the present investigation: 1) tests in which the temperature was maintained constant throughout the entire

Jan 1, 1958

By B. J. Reid, J. N. Greenwood

It has been shown1 that cavities are formed in the grain-boundaries of copper and 70:30 brass (as well as in magnesium) by the application of tensile stresses at elevated temperatures. For a given rate of strain, cavities are formed in brass at a lower temperature than in copper, and they are larger; it was thought that this earlier onset of cavitation in the alloy might be caused by the distortion produced in the metal lattice by the alloying element. If the cavitation is caused by the vacancy-migration mechanism, ' the distortion of the lattice would reduce the energy required for vacancy formation, and thus provide vacancies more readily to assist in the cavitation process. It was decided to study a range of alloys to find out whether increasing amounts of an alloying element would cause any progressive increase in, or modification of, the cavitation in copper. Nickel was chosen for this purpose, since it is soluble in copper throughout the whole range of alloys. A further advantage was its low vapor pressure, which enabled the preparation of the alloys in vacuum and the consequent reduction of their hydrogen content. It has been suggested that cavities may be nucleated by the migration of hydrogen atoms to the less regular atomic spacing at the boundary, and their combination to form molecules. The latter being too large to diffuse back into the lattice, form stable cavities into which vacancies could condense. PREPARATION OF ALLOYS All alloys, ranging from pure OFHC copper to 43.7 at. pct of nickel (carbonyl), were prepared in a vacuum furnace employing high-frequency induction heating. When a charge was melted, vigorous gas evolution occurred initially, after which the pressure was reduced to 10-4 mm Hg, using an oil-diffusion pump. After remaining molten for a further 1/2 to 1 hr to aid degassing, the melt was allowed to solidify in the crucible. In this way contamination by gases evolved from the surface of a separate mold was avoided. The list of alloys prepared is shown in Table I. The percentage of hydrogen present in the OFHC copper was reduced from 0.0054 at. pct to 0.0012 at. pct, as measured by a vacuum-fusion method. The alloys were cold-rolled to 0.03-in.-thick strip, and were homogenized in vacuum for 1 hr at 900°C after every 30 pct reduction. At a thickness of 0.05 in., the strip was held at 450°C for 24 hr under high vacuum (10-5 mm Hg) in an attempt to reduce the hydrogen content still further. Tensile specimens were prepared with a gage length of 1 in., and were finally annealed for 2 hr at 800°C to give an average grain diameter of 0.1 mm. TENSILE DEFORMATION The specimens were deformed in a tensile straining machine operated by a synchronous motor at a constant rate, equivalent to 1.7 pct per hr on a 1-in. gage length. The specimen and grips were contained in a vacuum jacket. A pressure of 10-2 mm Hg was maintained, which was sufficient to prevent surface tarnishing of a specimen held at 650°C for 24 hr. Tests were made between 20. and 650°C and the temperature was controlled to within ±3° over the gage length. The load was measured by the deflection of a cantilever spring. a) Mechanical Properties-The ductility curves shown in Fig. 1 fall into two groups. Figs. 1(a) and (b) for copper and the 5 pct nickel alloy, respectively, show a continuous fall in ductility with a steep fall between 200° and 400°C. Figs. l(c) to (f) show the same sudden loss of ductility between 200° and 400°C. With higher temperatures, however, there is a recovery in ductility values to a maxi-

Jan 1, 1959

By Stephen Taber

A vein may be defined as an aggregation of mineral matter, more or less tabular or lenticular in form, which was deposited from solution and is of later origin than the inclosing rock. This definition differs from the one found in many text-books in that no assumption is made as to the origin of the space occupied by the vein or the manner in which the mineral matter was deposited. In the present paper the writer purposes to discuss the mechanics of vein formation, and does not wish to begin by begging the question. The origin of ore deposits has been diligently investigated in recent years, but, while much has been written concerning the chemistry of the process, the physical side of the question has received less attention. The source of the ore minerals; the chemical composition of ore-bearing solutions; the relative importance of magmatic and meteoric waters as agents of concentration; and the causes of mineral precipitation have all been discussed at length. On the other hand, little has been written concerning the mechanics of vein formation, and the theories given in text-books today are essentially the same as those developed by the early Cornish and Saxon miners. Early investigators often regarded both veins and dikes as igneous in origin, but today the theory that vein minerals have been deposited from solutions, either liquid or gaseous, is firmly established. The latter view is supported by the fact that many vein-forming minerals are not found in unaltered igneous rocks; by evidence obtained in the laboratory regarding the solubility of minerals; by the presence of many ore minerals in hot-spring waters; by the occurrence of some veins in regions consisting exclusively of unaltered sedimentary rocks; by evidence as to the temperature at which some minerals are formed; and by the absence of mineral segregation due to difference in specific gravity. There is still, however, much difference of opinion as to whether certain tabular-shaped masses should be classed as veins or as dikes. Some of the earlier investigators have also advocated the theory that veins are contemporaneous in origin with the inclosing rock, while others have believed the vein minerals to represent a recrystallization or transforma-

Jan 1, 1920

By Fred C. Bond and

This paper is a continuation of two earlier papers,12 and presents new data on the grindability of various ores and other materials—the results of several years of intermittent research work on the nature of grinding and interpretation of test results. It is divided into five parts: 1. The tabulated results of several hundred grindability tests on a wide variety of ores. 2. A method of correcting screen analyses and calculating from them the surface and other properties. 3. A description of a new method of measuring the "surface energy" of an ore by pendulum impact tests. 4. Test results. 5. A general discussion of the test results and their application to grinding problems. 1. GRindability of Various Ores This part is a continuation of the paper listed as reference No. 1. The method of testing is described in detail in that paper. The sample to be tested is crushed to all through 6 mesh in rolls set at 1/16-in. opening in closed circuit with a screen. Of this sample 700 C.C. is ground dry in a laboratory ball mill under constant conditions of mill speed and ball charge in closed circuit with a screen of the desired size at 250 per cent circulating load. The mill is cylindrical, 12 by 12 in., and rotates at 70 r.p.m. It contains a charge of 285 iron balls weighing 20,125 grams and ranging from 1½ to ¾ in. in diameter. Each test is continued for a sufficient number of periods to establish equilibrium at 250 per cent circulating load, or until the composition of the circulating load is constant for successive periods. Tests are conducted at the mesh size to which the ore is to be ground in practice, and the results are expressed as the net production in grams of screen undersize per revolution of the mill. This is designated as the

Jan 1, 1939

By Fred C. Bond and

This paper is a continuation of two earlier papers,12 and presents new data on the grindability of various ores and other materials—the results of several years of intermittent research work on the nature of grinding and interpretation of test results. It is divided into five parts: 1. The tabulated results of several hundred grindability tests on a wide variety of ores. 2. A method of correcting screen analyses and calculating from them the surface and other properties. 3. A description of a new method of measuring the "surface energy" of an ore by pendulum impact tests. 4. Test results. 5. A general discussion of the test results and their application to grinding problems. 1. GRindability of Various Ores This part is a continuation of the paper listed as reference No. 1. The method of testing is described in detail in that paper. The sample to be tested is crushed to all through 6 mesh in rolls set at 1/16-in. opening in closed circuit with a screen. Of this sample 700 C.C. is ground dry in a laboratory ball mill under constant conditions of mill speed and ball charge in closed circuit with a screen of the desired size at 250 per cent circulating load. The mill is cylindrical, 12 by 12 in., and rotates at 70 r.p.m. It contains a charge of 285 iron balls weighing 20,125 grams and ranging from 1½ to ¾ in. in diameter. Each test is continued for a sufficient number of periods to establish equilibrium at 250 per cent circulating load, or until the composition of the circulating load is constant for successive periods. Tests are conducted at the mesh size to which the ore is to be ground in practice, and the results are expressed as the net production in grams of screen undersize per revolution of the mill. This is designated as the

Jan 1, 1939