Search Documents

By E. I. Larsen, F. R. Hensel

According to statements by Guertler1 Smith and Hamilton were the first to study the copper-titanium alloys, but owing to the presence of large amounts of impurities their data are inconclusive. M. A. Hunter and I. W. Bacon later investigated the electrical conductivity and the temperature coefficients at room temperature. The present writers reported their results2 in November, 1930. Recently Kroll published data on copper-titanium alloys3 which agree closely with those obtained by the authors. Material Tested The titanium used was in the form of square sintered rods, the analysis of which runs as follows: titanium, 95.4 per cent; silicon, 0.7; iron,l.8; aluminum, 1.4; copper, 0.1; manganese, 0.05. The ingots were prepared in a high-frequency induction furnace in air atmosphere. Their analyses are given in Table 1. Up to 5 per cent titanium the alloys could be forged. Above that amount they were red short and broke up easily. Owing to their rapid absorption of nitrogen and oxygen from the air, the alloys with the higher amounts of titanium tend to form surface films which greatly increase the casting difficulties, especially when small masses of metal are handled. It was, however, possible to prepare sound ingots up to 25 per cent titanium. Thermal and X-ray Investigation The cooling curves of some of the alloys are plotted in Fig. 1, and R tentative diagram constructed from these data is given in Fig. 2. From this it is evident that the solid solubility of copper for titanium is approxi-mately 4 to 5 weight per cent titanium at 878" C., which is the eutectic temperature. The melting point of copper is lowered gradually by adding

Jan 1, 1932

By R. V. Sara

Determination of the Hf-C phase diagram was conducted primarily by metallographic and X-ray diffraction studies on appropriate alloys. The only intermediate phase observed in this binary system was HfC. This phase was found to be homogeneous between 34.0 and 48.0 at. pct C at 2200°c and between 36.0 and 49.3 at. pct C at 3150°C. The lattice-parameter variation was also determined for HfCI-, compositions prepared at 2200° and 3150°C. The most most refractory composition, with a melting point of 3830°c, was established at 47.5 at. pct C from melting-point data. Solidus temperatures of 2240' and 3150°C occur on the high-kafnium and high-carbon sides of the monocarbide, respectively. The invariant point between HfC and carbon is located at 66.0 at. pct C, whereas the 2240°C solidus corresponds to the peritectic temperature at which hafnium is formed from HfC and hafnium-rick liquid. Hafnium has a melting temperature of 2208°C and is capable of taking carbon into solution to the extent of 10.5 at. pct at this temperature. ALTHOUGH the Hf-C phase diagram has not been previously evaluated experimentally in its entirety, the belief has been that the general configuration would resemble the chemically similar Group rV carbide systems, Ti-C and Zr-c.' These binaries are characterized by a single carbide phase with a simple NaC1-type structure which is maintained over wide compositional ranges. This family of carbides has high thermal stability that increases substantially as the atomic number of the metal component increases. This trend characterizes HfC as one of the highest melting materials. According to Agte and Alterthum,2 the melting point for this monocarbide is 3890°C, a value that has been quoted quite extensively for the past several decades. Recently, in repeating the work of Agte and Alter-thum, Adams and Beall3 determined the melting point of HfC to be 3895°C. A significant departure from the commonly accepted version of the Hf-C system was reported by Avarbe and his coworkers,4 who proposed that there is an extreme stabilization of a hafnium in a narrow field to 2820°C, above which it melts peritectically to form HfC and liquid. Their study was also concerned with the melting temperature of various HfCI-, compositions, but the peak melting point was taken from the work of Agte and Alterthum. Avarbe and his associates were not concerned with the high-carbon region of the system. However, three widely varying temperatures have been reported for the HfC-C solidus by other investigators. Cotter and Kohn5 observed approximately 2800°C; Portnoy et al.' reported 3260°C; and, more recently, Krikorian7 indicated 2915°C. Equally as uncertain is the solidus between hafnium and HfC. As noted above, Avarbe et al. report a peritectic temperature of 2820°C, Krikorian7 measured 2150°C, and Benesovsky and Rudy' estimated 2000°C on their diagram. I) EXPERIMENTAL PROCEDURE The starting materials for this study consisted of reactor-grade hafnium hydride obtained from Fair-mount Chemical Co., Newark, N.J., hafnium carbide supplied by Wah Chang Corp., Albany, Ore., and Union Carbide spectroscopic-grade graphite, SP-1. The graphite analysis indicated impurities at levels of only 0.5 ppm or less. According to the suppliers, the hydride and carbide contained the typical impurities listed in Table I. The samples required for these studies were prepared by dry blending either graphite and hafnium hydride or hafnium hydride and hafnium carbide powders for approximately 5 min in a "Spex Mixer Mill". The latter combination was used only for preparing several samples in the HfC1-, melting-point studies. Small pellets, varying between 3/16

Jan 1, 1965

By George S. Rice

MECHANIZATION in coal mining is a phrase which has attracted world-wide attention, and those persons not engaged on the practical side of coal-mine operations seem to regard mechanization as a panacea for many difficulties of the industry. The term "mechanization" as now employed by experienced mining men is restricted to mean mechanical loading of coal at the face. In a broader sense mechanization in coal mining was begun nearly half a century ago with the introduction of compressed-air undercutting machines and locomotives and, later, of electrically operated locomotives, undercutting and shearing machines, and drills. The use of coal-cutting machines, which has increased until now about three- fourths of the bituminous coal produced is being mechanically cut, first displaced hand-picking except in a few long-wall mines, and later gradually displaced the dangerous and coal-smashing method of blasting-off- the-solid.

Jan 1, 1929

By I. J. Polmear

Earlier work revealed that small amounts of silver (< 0,l at. pct) may exert a marked effect on the structure and aging characteristics of certain a1loys based on the Al-Zn-Mg system. Silver additions have now been made to other age-hardening aluminum alloys, and significant effects have been observed in the Al-Mg system and in several Al-Cu-Mg and Al-Mg-Si alloys. Similarities exist between the behavior of alloys from all four systems, notably that in each case silver stimulates nucleation of an intermediate precipitate which forms when the alloys are aged in the medium temperature range (-120" to 220°C). The mechanism for this effect is uncer- IT has been shown that small additions of silver (<0.1 at. pct) may have a marked effect on the structure and age-hardening characteristics of tain although it is suggested it originates in a preferred affinity between magnesium and silver atoms. There is evidence to indicate that the effects of silver are unique to that element. It is suggested that silver atoms interact with vacancies during low-temperature aging of Al-4 pct Cu and certain Al-Cu-Mg alloys. Silver had little effect on Al-8 pct Zn aged at any temperature. Preliminary observations indicate that silver may have interesting effects on the strength properties of Al-Mg alloys, md a the commercial Al-Cu-Mg alloys designated as 2024 and 2618. many alloys based on the Al-Zn-Mg* system.1"&apos;*

Jan 1, 1964

By R. T. Hukki

THE accepted basis of comparisons between mills of different diameter is the percentage critical speed. If n = actual mill speed, rpm, nc = calculated critical speed, rpm, np = calculated percentage critical speed, and D == inside diameter of the mill in feet, then n, In the following analysis capacity, T, is expressed in short tons per hour, tph, and power consumption, P, in kilowatts, kw. Accordingly power consumption per unit of capacity, P will be expressed in kilowatt hours per short ton, or kw-hr per ton. In all equations D refers to the inside diameter of the mill in feet and v to the peripheral speed of the mill in feet per minute inside the liners. &apos; Comparison between separate mills must be based on equivalent grinding conditions, i.e., same feed, same size distribution of feed, same size distribution of product, and same percentage of solids. In addition, comparisons between separate rod mills must be based on the same rods, same type of liners, and same percentage rod load. Comparisons between separate ball mills presuppose the same balls, similar liners, and same relative ball load. The practical np-range through which the equations apply varies, being narrower for fine grinding in ball mills and wider for coarse crushing in rod mills. The Relationship between Capacity and Speed It is the general belief that the capacity, T, of a tumbling mill is directly proportional to the speed of the mill, other things remaining constant.&apos; Mathematically this is represented by the equation T - c¹ n tph [4] where c, is a factor related with the grinding characteristics of the ore, method of reduction, and the units chosen. It is proposed here that the general equation relating mill capacity and speed should be of the form T = c¹ nm tph [5] In other words, the capacity should be proportional to the mill speed raised to power m, the numerical value of the exponent being 1 5 m 5 1.5, depending on the circumstances. Eq. 5 can also be written in the following forms: T = c, (np)m tph, and [6] T=Ca vm tph, [71 where v = peripheral speed of the mill in feet per minute. If the observed capacity of a mill at speed n¹ is = T¹ tph, the capacity T² of the same mill at speed n² should be T² = T¹ (n²/n¹)tph [8] The Relationship between Power Consumption, Mill Diameter, and Speed The only well known theoretical deduction relating power consumption, P, and mill diameter appears to be the formula of duPont introduced by Gow, Guggenheim, Campbell, and Coghill.&apos; According to duPont, the power required to operate a mill is a function of the mass of the balls, of the lever arm of the ball mass, and of the speed of the mill. The ball mass per unit of mill length is proportional to the square of the diameter, the lever arm is directly proportional to the diameter, and the critical mill speed or any percentage thereof is inversely proportional to the square root of the mill diameter. Following this reasoning, the original duPont formula is of the form P = c4D² c D • c6D-0.5 = c7D2.5 [9] If the mill speed in the above equation is expressed in terms of Eq. 3, the duPont formula may be written as follows: P=f1(D2) f2(D) f³(—np) or [10] vD P = c np D2.5 kw [11] Eq. 11 may also be derived from the mechanical principle of force, which is equal to mass x acceleration. Power necessary to operate a mill may be considered to be an homogeneous linear function of the force developed. Ball or rod mass per unit of mill length is a function of D2. The acceleration factor of the ball or rod mass is a function of the peripheral speed of the mill. Thus P = f4(F) = /x(D2) f5(v) Indicating that v = nDn, and n = c9 np /vD, the above equation becomes P = f2 (D2) -fa (D ca np/vD

Jan 1, 1955

By W. A. Oates, J. A. Lambert, P. T. GaIIagher

Monte Carlo methods have been used to compute the arrangements of interstitial atoms dissolved in tetrahedral sites in bcc lattices. It is assumed that the presence of an interstitial atom "blocks " a certain number of neighboring sites and prevents their occupancy. Sites "blocked" by more than one filled site are allowed for. The computed values of. the mean occupation number (defined as the ratio of the total number of sites blocked to the number of solute atoms are used to calculate the configurational entropies of the solutions. These entropies are compared with those resulting from previous theoretical studies of this problem and also with available experin~ental data for the p Zr-H, Nb-H, V-H, and Ta-H systems. Evidence is also given that the "blocking" explanation of low limiting compositions in these systems, rather than this being due to initial limitations on the number of sites available, is probably correct. THE ideal partial configurational entropy of mixing of an interstitial solute in a metal is given by: where p is the number of interstitial sites per metal atom and Xi is the atomic fraction of the interstitial. For the bcc lattice. which we shall be concerned with in this paper, the interstitial positions are shown in Fig. 1. It can be seen that for the tetrahedral sites, p=6. whereas for the octahedral sites, p = 3. Different emphasis has been placed on the relative importance of energy and entropy effects in determining deviations from ideality in interstitial solid solutions. In some cases the same system, e.g., Fe-C, has been described by the contradictory regular and athermal solution models indicating that the enthalpy and entropy functions, derived from equilibrium data, are frequently not accu.rate enough to differentiate between these treatments. However, for certain metal-hydrogen solutions the equilibrium data is available over sufficiently wide ranges of temperature and composition to permit a reasonably accurate determination of the compositional variation of the heats and entropies. Hoch&apos; has attempted to interpret the results of interstitial solid solutions in terms of a regular solution model. In the case of the Ta-H system where 13 = 6, this model entails fitting the experimental relative partial entropies of solution, asH, to the equation: where ASgs is the relative partial excess entropy of solution of hydrogen. Hoch found that the results of Mallett and Koeh1 could be fitted to this equation with an approximately constant value of AF up to XH = 0.25. However, it is apparent from the solubility isotherms in this system which become asymptotic to the composition TaH that, since (Xh /6 - ~Xh ) becomes infinite only at TaH6, it is necessary that AS<&apos; tends to infinity at TaH. In other words, the low saturation composition of TaH, instead of the anticipated TaH,, eliminates the possibility of applying regular solution theory to such systems. Rather large negative excess configurational entropies must exist at higher hydrogen concentrations in order to explain the lower saturation values. To account for these low limiting compositions and excess entropies two distinctly different approaches have been followed. Rees and many others1-l2 have assumed that not all interstitial sites are crystallographically equivalent with respect to the interstitial addition; that is, in Eq. [I] p is less than the value anticipated from geometrical considerations. To describe, say, a bcc metal-hydrogen system with a limiting composition of MH by this approach one would consider that p = 1 in the first instance instead of p = 6.&apos;j3 In some cases, nonintegral values of B have been taken in order to improve the fit with the experimental data over limited ranges of composition. The other approach which has been used to explain the low saturation compositions is to assume that, although all sites are available for occupancy, strong repulsive interactions exist between the neighboring interstitial atoms, and hence occupancy of any site excludes or blocks a certain number of neighboring sites from being occupied. Earliest treatments of this concept considered the exclusion of an integral number, of nearest-neighbor sites from being occupied at all concentrations. In this case, the partial configurational entropy is given by: These early treatments failed to allow for the overlap of the blocked sites which will arise at all but the very lowest concentrations. More recently attempts have been made to calculate the effect of this decrease in the number of blocked sites on the configurational entropy. Using the quasichemical treatment of interstitial solid solutions as given by Lacher and assuming that an infinite repulsive interaction energy existed between the solute atoms. atom obtained an approximate configurational entropy applicable to the blocking with overlap case:

Jan 1, 1970

By S. Feuerstein

THE influence of environment on the mechanical properties of metals has been extensively studied and documented.&apos; Most investigations have dealt with an interaction between a particular environment and a specific metal surface and the concomitant change in bulk mechanical behavior. Typical contributing media are oxide and metal film:;, electrolytes, and other surface-active agents. In the last category fall controlled gaseous environs (i.e., pressure or vacuum). Most vacuum exposure experiments prior to 1963 were conducted at pressures s>10-6 torr and elevated temperatures, or in such a manner as to prolong the exposure (e.g., by stress-rupture, creep, and fatigue). Little attention has been given to vacuum environment effects on the mechanical behavior of metals subjected to simple uniaxial deformation at room temperature. Test times and temperatures were assumed too ineffective as far as bulk changes were concerned. Further, the contribution of surface effects to the bulk mechanical behavior of metals was considered minimal. Under vacuums of the order of 1.0- 8torr and higher, molecular densities and, consequently, the rate of monolayer formation are such that exposures from seconds to days would be required for complete gas coverage. Thus, atomically clean surfaces created under ultra-high vacuum could conceivably maintain their cleanliness for time intervals orders of magnitude greater than at higher pressures. The influence of this unusual type of environmental surface phenomenon on the short-term bulk mechanical behavior of aluminum was first observed by Krame and Podlaseck in 1963.&apos; kin equivalent effect was reported for magnesium by Williams and Nelson.3 It was concluded from these studies2,3 that vacuum and, consequently, the monolayer formation rate of the oxide, were responsible for the described changes in flow behavior. The presence of an oxide layer impedes dis- I) EXPERIMENTAL DATA: MOLYBDENUM The tensile behavior of molybdenum was investigated by the author4-6 at ambient temperature over a range of pressures from 760 to 10-10 torr. These studies revealed that the flow behavior of the bulk specimens (0.200 in. diam by 2 in. gage length) was independent of pressure on sintered (0.062 mm grain size) and arc-cast polycrystals (0.012 to 0.149 mm grain sizes) and single crystals. Since the specimens were relatively large in size, it was assumed that any flow behavior effect would be surface-limited because of the short-term deformation procedure. Strain-rate-change experiments performed to determine the activation volumes for individual specimens at 760 to 10- 10 torr further indicated that the surface flow contribution was either minimal or zero, contrary to the findings of Shen el a1.7 on aluminum. Although the flow behaviors did not change, specimen ductility did change. For the sintered material at a strain rate of 4.2 x 10-4, specimen ductility was -9 pct higher at l0- 10 torr than at atmospheric pressure (dry nitrogen). A more comprehensive investigations on this same material revealed a distinct pressure dependence, Fig. 1. Intermediate and atmospheric pressure tests were obtained by backfilling the system from l0- 10 torr with extra dry, prepurified nitrogen. Other environments (air and purified argon) were also utilized for the 760 torr experiments; the results were essentially the same as those for dry nitrogen atmospheres. Departure from the fracture strain values obtained at 760 torr takes place in the vicinity of l0-6 torr, as indicated by the scatter band; a noticeable ductility increase is apparent at l0-8 and 10-10 torr.

Jan 1, 1970

By Allen L. Hatch

A survey of all phases of the world&apos;s lead and zinc production in 1968 from ore through to refined metal was conducted by sending questionnaires to individual companies ad the results of this survey are tabulated at the end of the paper. The paper goes on to review changes in the geographical distribution of the world&apos;s lead and zinc mine and metal production and in the trading patterns of raw materials, present and future utilization of metal production capacity, developments in metal smelting and refining processes and the growing importance of marketing, product development and research in the 1950&apos;s and 1960&apos;s.

Jan 1, 1970

By Robert A. Kinzie

PAGE Introduction.............334 Climate.............335 History............335 Geology.............341 Mining..............343 Shafts............343 Stations and Ore-Bins....345 Levels. Drifts. Cross-Cuts, Winzes. etc........347 Stoping Surface-Pits,......... 351 Underground Stoping........... 332 Chutes. Drilling. etc.....354 Tramming............. 358 Sampling. Maps and Assaying.........360 Labor.............361 Machinery.............362 Milling,..............362 Crushers.............366 Battery-Foundations...........368 Power (Water—Coal)...........373 Methods of Catching the Free Gold...374 Screens..............376 Apron-Plates,.......376 Concentration..........378 Clean-Up,.............378 Labor..............382 Costs..............382 Introduction. The Treadwell Group comprises five mines. four of which are situated on the northeast side of Douglas island. directly opposite the town of Juneau, and one about four miles back of Juneau. These mines are owned by four separate companies. but are all under the same general management. Those situated on Douglas island are : The Treadwell mine. owned by the Alaska Treadwell Gold Mining Co.. the Mexican mine. owned by the Alaska Mexican Gold Mining Co.; and the Ready Bullion and Seven-Hundred-Foot mines. owned by the Alaska United Gold Mining Co. The Juneau mine. owned by the

Jan 1, 1904

By Charles H. Thurman

THE data given herein were first included in a paper read before San Francisco Section, A.I.M.E., in October 1940, and are applicable to conditions existing until the gold-dredging industry was temporarily suspended by Order L-208 of the War Production Board in the fall of 1942. There is no doubt that gold dredging will be resumed at some future time, and on a scale equivalent to that of the recent past, but the cost data given herein will be affected to some extent by conditions existing at that time, and by labor rates and prices for materials then prevailing. DRAGLINE VS. BUCKET-LINE Dragline dredges should not be considered for mining large areas of low-grade placer gravel. In such deposits a dragline operator with a 5-cu. yd. dragline would be doing well to maintain an operating cost of 6¢ per cu. yd., while a bucket-line dredge with buckets no smaller than 7 cu. ft. each could be operated for less than 4¢ per cu. yd. By operating costs, I mean only field charges such as direct operating and overhead, which includes pay roll, power or fuel, repairs and maintenance, insurance, land clearing and general expenses, but not including such items as prospecting, depletion, depreciation of equipment, State Franchise Tax, or Federal Income Tax. It is not to be inferred that a dragline dredge cannot make a profit in small low-grade deposits, where the extent of a given property is too small to justify the use of the more costly bucket-line dredge. Consider small deposits of 10¢ gravel. It is obvious that a deposit of 5,000,000 cu. yd. of such gravel could not be mined profitably with a new, 7-cu. ft. bucket-line dredge, costing upward of $250,000, and with operation costs at 4¢ per cu. yd., paying for land or royalties out of earnings; nor could a new combination 5-cu. yd. dragline and washing plant, worth upward of $125,000 and working at 6¢ per cu. yd., make a profit. These comparisons are made because the hourly capacity of both types of dredges is nearly the same. The bucket-line dredge averages 93 per cent operating time in 24 hr., as against about 80 per cent or less for the dragline dredge. These percentages of operating time are important factors in making a comparison of this kind. The bucket-line dredge has greater efficiency in cleaning soft bedrock, usually characteristic of dredging deposits, and a 7-cu. ft. bucket-line dredge can be efficient to a total digging depth of 80 ft. (65 ft. below water, 15 ft. above). A 5-cu. yd. dragline dredge is limited to about 30 ft. of efficient digging depth, 5 ft. of which could be above water. In small areas of gravel not over 30 ft. deep, a 5-cu. yd. dragline dredge could make a profit where a bucket-line dredge could not do so. As an example: compare the dredging of 3,000,000 cu. yd. of 10¢ gravel 28 ft. deep with bucket line, costing 4¢ per cu. yd., and with a 5-cu. yd. dragline dredge operating at 6¢ per cu. yd. Because of small yardage, new equipment is not warranted, therefore we can assume that the dredges of both types are used equipment, fully depreciated. Dismantling, mov-

Jan 1, 1945

By S. W. Poole, J. A. Rosa

THE object of this investigation was to determine the distribution of chemical elements within a large, killed alloy-steel ingot, by sulphur printing and quantitative chemical analysis. With regard to segregation in steel ingots, the factors of melting practice, pouring temperatures, mold design, etc., and the mechanics of solidification and its attendant functions, have been the subject of intensive study over a period of years by many investigators. Notable among these is the Sub-Committee of the No. 5 Committee of the British Iron and Steel Institute. For an exposition 0f the many problems awaiting the researcher on the heterogeneity of steel ingots, the methods of attacking these problems, together with some of the answers, the reader is referred to the nine reports and numerous papers of that committee and its membership. STEELMAKING DATA Melt.-The heat was made in a 70-ton direct arc-type basic electric furnace. Furnace charge consisted of nickel-chromium-molybdenum steel, most of it in the form of heavy mill scrap. All of the scrap was charged cold. The standard double-slag method was employed, the heat being finished under a strong carbide slag. Aluminum was used as the deoxidizing agent. Tapping temperature, as observed with an optical pyrometer, was 3000°F. Detail of Mold and Ingot Size.-Details of the ingot mold and the ingot itself are given in Fig. I. Teeming.-Teeming temperature of the subject ingot as observed with an optical pyrometer was 2830°F. The ingot was top-poured directly through a 1 ½ in. nozzle and required 7 min., 44 sec. to fill up to the hot top. An additional 2 min., 30 sec. were required to fill the hot top. The ingot was stripped hot and charged with the remainder of the heat into an annealing furnace. There it was given the standard annealing cycle used for these ingots. Subsequent heat-treatments are described elsewhere in this paper. SECTIONING AND PREPARATION FOR SULPHUR PRINTING Because of previous favorable experience in sectioning ingots up to 21 ½ in. square with an oxyacetylene torch, it was decided to use this method to section the subject ingot. The ingot was preheated to 900°F. for 12 hr. It was then placed on a steel bed in a horizontal position so that the longitudinal axis was level and parallel to the track of the motor-driven torch carrier. Two cuts were made, one 2 in. above the longitudinal axis and the other 2 in. below. The time required to make each cut was approximately 75 min. The cutting operation is shown in Figs. z and 3. The 4-in. thick slab was mmediately charged into a furnace standing at 1200°F.

Jan 1, 1944

By G. Derge, R. E. Grace

A S detailed studies of mass transport in hetero- geneous systems are made, a knowledge of the chemical diffusion coefficients in various liquid and solid phases is necessary to understand the kinetics of any total reaction. For example, in zone refining some information must be available about the diffusion coefficients of various species in the liquid and solid regions near the moving interface. In liquid-liquid reactions, of which slag-metal reactions are of particular interest to metallurgists, the diffusion coefficient of a transferring species must be known accurately in both phases in order to predict a transfer coefficient for the over-all process. Diffusion data for various elements in liquid iron and iron-carbon alloys have been roughly deter-

Jan 1, 1959

By C. G., Fink

The dissolution of gold by cyanide solutions was studied by determining the time required for the solvents to dissolve gold leaf. Minute traces, even 0.5 ppm, of sulphide ion retard the dissolution of gold, and this behavior cannot be accounted for by the presently accepted hypotheses involving oxygen-depletion or thiocyanate formation. On the other hand, traces of the salts of lead, bismuth, mercury, and thallium considerably accelerate the dissolution. The beneficial effect of lead is dependent upon the pH and cyanide ion concentration of the solution.

Jan 1, 1950

By S. W. Poole, J. A. Rosa

The object of this investigation was to determine the distribution of chemical elements within a large, killed alloy-steel ingot, by sulphur printing and quantitative chemical analysis. With regard to segregation in steel ingots, the factors of melting practice, pouring temperatures, mold design, etc., and the mechanics of solidification and its attendant functions, have been the subject of intensive study over a period of years by many investigators. Notable among these is the Sub-committee of the No. 5 Committee of the British Iron and Steel Institute. For an exposition of the many problems awaiting the researcher on the heterogeneity of steel ingots, the methods of attacking these problems, together with some of the answers, the reader is referred to the nine reports and numerous papers of that committee and its membership. Steelmaking Data Melt.—The heat was made in a 70-ton direct arc-type basic electric furnace. Furnace charge consisted of nickel-chromium-molybdenum steel, most of it in the form of heavy mill scrap. All of the scrap was charged cold. The standard double-slag method was employed, the heat being finished under a strong carbide slag. Aluminum was used as the deoxidizing agent. Tapping tempera- ture, as observed with an optical pyrometer, was 3000°F. Detail of Mold and Ingot Size.—Details of the ingot mold and the ingot itself are given in Fig. I. Teeming.—Teeming temperature of the subject ingot as observed with an optical pyrometer was 2830°F. The ingot was top-poured directly through a 1 1/2-in. nozzle and required 7 min., 44 sec. to fill up to the hot top. An additional 2 min., 30 sec. were required to fill the hot top. The ingot was stripped hot and charged with the remainder of the heat into an annealing furnace. There it was given the standard annealing cycle used for these ingots. Subsequent heat-treatments are described elsewhere in this paper. Sectioning and Preparation for Sulphur Printing Because of previous favorable experience in sectioning ingots up to 21 1/2 in. square with an oxyacetylene torch, it was decided to use this method to section the subject ingot. The ingot was preheated to 900°F. for 12 hr. It was then placed on a steel bed in a horizontal position so that the longitudinal axis was level and parallel to the track of the motor-driven torch carrier. Two cuts were made, one 2 in. above the longitudinal axis and the other 2 in. below. The time required to make each cut was approximately 75 min. The cutting operation is shown in Figs. 2 and 3. The 4-in. thick slab was mmediately charged into a furnace standing at 1200F.

Jan 1, 1945

All indications point to a most interesting and successful meeting in Chicago on Sept. 22-27. Already 140 papers have been submitted to the Committee on Papers and Publications. Of this number 46 deal with pyrometry, 17 with iron and steel, and 24 with coal. The tentative program is as follows: PROGRAM OF CHICAGO MEETING Monday. Morning-Registration. Oil. Afternoon-Technical Sessions. Coal. Milling, Industrial, and Iron Geology. Evening-Smoker. Tuesday.- Morning and Afternoon-Excursion by boat to Gary and trip through United States Steel Co.&apos;s plant. Technical session on Ferrous Metallurgy on the boat, return trip Evening-Technical Session. Wednesday. Morning-Technical Sessions {Ferrous Metallurgy. Mining. Afternoon-Technical Sessions {Ferrous Metallurgy. Non-ferrous Metallurgy... Evening-Banquet, Congress Hotel.

Jan 7, 1919

By K. Leutwyler

The authors present an interesting review of various applications of rather well known theories. Their rearrangement of the original working equations is strictly computer oriented and serves well to that effect; however, the new appearance will be confusing to the slide rule-wielding members of the profession. In reviewing discrepancies existing between calculations made by Baker Oil Tools, Inc. field engineering staff members and computer output submitted based on the authors&apos; program, the following error in concept was discovered in Eq. 4. The authors quote the length change due to helical buckling in the following form We appreciate Kurt Leutwyler&apos;s awareness of Archimedes&apos; principle, and concur that the final term in the denominator of Eq. 4 results in a small error. Examples checked revealed less than I ft error, and corrective expressions for the four possibilities of displacement follow. The portion of the denominator within extra large brackets represents the original term W,, = weight of outside fluid displaced per unit length. The authors interpreted the expression "displaced" in general oilfield terminology as a fluid displacement, such as "mud displaced with water, etc." A review of the theory forming the basis for these helical buckling calculations discloses that this displacement is meant to be interpreted in the Archimedean sense, i.e., fluid displaced by the solid body. here the tubing and the seal nipple. Lubinski* illustrated the point by summing moments due to mechanical and hydraulic forces acting on a free body immersed in fluid. This moment summation, always in the Archi,medean sense, yields effects of the real forces, including W,, and the fictitious force on the bending mechanism. I would be interested to hear the authors&apos; comments regarding this theoretical point, which nevertheless is not mute since its lack of recognition seems to result in erroneous calculations. We must not remain mute to Leutwyler&apos;s suggestion that these equations, although computer oriented, are confusing to the slide rule engineers. Such input information as density in pounds per gallon, pipe diameters in inches, pumping rate in barrels per minute and pipe length in feet is not confusing to most of us. Yet there may be some rugged individuals in field positions who carry tables of conversion constants and have committed to memory such items as coefficients of thermal expansion and Poisson&apos;s ratio; however, even this type of individual would welcome a simplified equation occasionally. M

By Carl E. Swartz

For many years kettles used in the melting and refining of lead and other nonferrous metals and alloys have been made of cast iron. The logic of this probably lies in the fact that cast iron has been known as a material of construction for vessels of this type much longer than steel, and satisfactory fabrication from it has been more easily accomplished and better understood. As the capacity of lead refineries has increased, it has been only natural to increase the size of kettles. Today kettles of 150 to 250 tons are not uncommon. As the size of the kettles increased and better shapes were designed, the uniformity of material of construction became more important. Records kept over comparatively long periods of time have shown that the length of service of kettles has not been uniform. Many causes contribute to this and the importance of each has not yet been evaluated. Kettle design, kettle setting, method of firing and material of construction have been changed from time to time to obtain better service, but the variation in length of service is still great. A kettle may fail during the first few heats or may last through more than one thousand heats. The purpose of this article is not to present the conclusions of a finished piece of research on kettle manufacture and use, but to present a series of observations made over considerable time in the hope that others will publish data and that all may be correlated into a logical scheme which will result in better service and longer kettle life.

Jan 1, 1931

By Charles Fettke

IN THE present day manufacture of glass nearly pure quartz sands are used almost exclusively as the source of the silica, which is the major constituent of all common varieties of glass. Ordinary soda-lime, such as bottle, common tableware, plate, and window glasses, contain from 65 to 75 per cent. of silica. OCCURRENCE Glass sands occur in nature either in the form of loose, unconsolidated sediments or in deposits in which the individual grains have been more or less thoroughly bound together by some cementing agent so as to form sandstones. While deposits of sand and sandstones occur both widely and abundantly distributed, deposits that are sufficiently free from other constituents than quartz grains, so that they can be employed in the manufacture of the better grades of glass, are, comparatively speaking, of rare occurrence. The major portion of the glass sand produced in the United States comes from sandstones. In order to be suitable for glass sand, they should be rather friable. The rock should break down readily along the cementing material between the grains and should not break across the grains rather than along the bond. Some of the sandstones used are so friable that only light shots of slow-burning dynamite are necessary to disintegrate them sufficiently for hydraulic mining, while others have to be passed through crushers in order to disintegrate the rock into its individual grains.

Jan 2, 1926

By L. O. Millard

Stockpiles in the minerals industries serve a wide variety of purposes. Usually they are for surge between stages of processing, for a dependable plant feed in anticipation of delays, or to provide for single or double shift mining in conjunction with round-the-clock milling. Often surge piles are necessary to insure a uniform feed to continuous process equipment where the material is received as an intermittent or variable flow. Extensive use is made of stockpiling for the primary purpose of blending. The significant fact about all stockpiling of bulk materials is that storing and reclaiming are two separate and distinct operations and they may present widely different problems in the selection of methods and tools.

Jan 10, 1959

By D. E. Norquist, J. E. Moeller

The results of wear on marked balls, 4, 31/2, 3, and 2 in. diam are given. All balls were forged steel of practically the same chemical analysis and hardness. The results indicate that balls in a given mill for a given length of time will have equal diameter losses, regardless of size.

Jan 6, 1950