Search Documents

By W. D. Robertson, R. E. Reed-Hill

DEFORMATION of magnesium crystals in a direction parallel to the basal plane has a special significance as a result of the preferred orientation characteristic of cold worked and recrystallized polycrystalline magnesium sheet and extruded rod in which the basal plane tends to lie in or near the plane of the sheet or the axis of a rod. The principal objective of the present study is a determination of the modes of plastic deformation in magnesium single crystals in this orientation. Evidence for nonbasal slip in magnesium has been presented by a number of authors. Schmid and Was-serman&apos; indicated that pyramidal slip on {1011} < 1120> or {1012} <1120> could occur above 225°C. Bakarian and Mathewson2 stablished that the slip system {1011} <1120> operates at high temperatures and that 225°C was a lower limit for pyramidal slip. The latter authors also showed that the critical resolved shear stress for {1011} slip was 400 g per sq mm at 330°C, while that for basal slip was 66 g per sq mm at the same temperature. Thus, at 330°C basal slip should be expected for all orientations except those in which the stress axis lies almost in the basal plane. More recently Burke and Hibbard3 oserved pyramidal slip at 25°C, when the stress axis was 6" to the basal plane and 14" to a <1120> slip direction. The critical resolved shear stress for pyramidal slip was 52 g per sq mm, which is only slightly greater than their value for basal slip (46 g per sq mm). Chadhuri, Chang, and Grant4 have observed non-basal slip in creep tests with polycrystalline specimens in the temperature range 250" to 350°C. The observed slip bands, which were extremely irregular in appearance, can be explained in terms of cooperative slip on {1011} and (1010) planes which have a common slip direction. Prismatic (1070) slip in polycrystalline magnesium was observed by Hauser, Landon, and Dorn.5 It was found to occur at low temperatures (78" and 195°K) and it was accompanied by cross slip in which the cooperating plane was the basal plane. Since prismatic slip occurred only at regions of high stress concentrations, the critical resolved shear stress could not be determined. Experimental Procedure The present work was performed on crystal specimens which were all cut from the same large single crystal. The original cylindrical crystal, 0.5 x 7 in., was grown in a Bridgman type furnace in which the temperature gradient was moved past the stationary crystal in the manner described by Jillson6 and Burke.&apos; High purity magnesium was furnished by the Dow Chemical Co. with the following spectro-graphic analysis in weight percent: 0.003 pct Al, <0.01 pct Ca, 0,002 pct Cu, <0.001 pct Fe, 0.008 pct Mn, <0.001 pct Ni, <0.002 pct Pb, <0.01 pct Si, <0.001 pct Sn, and <0.01 pct Zn. The large crystal was cut into four cylindrical pieces about 1.5 in. long. A flat surface parallel to the basal plane was made by hand grinding with lubricated metallographic paper on one side of each cylinder. In order to prevent bending in subsequent cutting operations, the crystals were supported by

Jan 1, 1958

By P. H. Mell

AMONG the minerals exhibited at the Atlanta Exhibition of 1881, soapstone, kaolin, and asbestos were well represented. The first two occur in large quantities, of very pure quality, throughout the South. The last is somewhat limited in amount, get in certain localities it exists in masses sufficiently large to pay for working; in North Carolina, Georgia, and Alabama it has ken mined with some profit. I would, in this paper, call special attention to the minerals soapstone and kaolin, because their many valuable qualities seem to have been almost entirely overlooked by our Southern manufacturers. Steatite, particularly, occurs in such large quantities, and generally in such close proximity to the great iron regions of Alabama and Georgia, that it is anlazing that the iron companies will persist in sending abroad under heavy expense for firebrick. It would require a much smaller sum of money to quarry this rock and place it at the various furnaces ; and the results obtained, I am sure, would prove its superiority over the majority of firebrick brought into this region. Soapstone, as well as kaolin, is found throughout the metamorphic regions of Alabama, Georgia, South Carolina, and North Carolina. Below will be found seven analyses that I have made of this mineral, taken from various points in the four States above mentioned. I have also subjected these same specimens to severe fire-tests, and the results were very satisfactory. The tests mere canducted in the following manner: Small portions of the compact variety were carefully weighed and placed in a Fletcher&apos;s new crucible furnace for gas, and subjected for half an hour to a heat that will in 12 minutes fuse iron. The only effect upon these specimens was a slight change in color to a darker shade, a small loss in weight, due evidently to the evaporation of water, and, in one or two specimens, a slight degree of fusion on the sharp edges. The first specimen subjected to investigation was taken from a large outcropping in Tallapoosa County, Alabama. Specific gravity, 2.88 ; hardness, 1.9; color, blue gray. Composition: Water,....2.68 Silica,..........65.48 Iron oxide,.........2.10 Alumina,.........15.02 Magnesia,... 15.35 10061

Jan 1, 1882

By Fred D. Gustafson

With the postwar emergency for new housing and for new industrial buildings, much research has been done on lightweight aggregates for use in concrete and plaster. The trend toward lighter weight aggregates to relieve the dead load on the higher, steel framework buildings started toward the end of the last century. Progressively the requirements became more stringent, crushed bank slag, weighing 80 lb per cu ft as compared to 100 lb for crushed rock, was supplemented in some sections by foamed slags and expanded shales weighing from 40 to 60 lb per cu ft. In other sections cinders were used weighing from 40 to 50 lb, including sand. Sections favored with more recent vulcanism turned to pumice weighing from 30 to 60 lb, whereas other localities made use of diatomite, from 28 to 40 lb. Exfoliated vermiculite weighing from only 6 to 10 lb per cu ft came into use. As the search for lighter weights in aggregates continued so did the search for other desirable properties such as nailability, ease of cutting or channeling, and good insulation to both sound and heat. This search eventually led to a widespread interest in the expansion of perlite, or similar volcanic glasses, with the result that in 1946, the Office of the Housing Expediter&apos; listed eleven firms reporting the operation of processing plants either on pilot or commercial scale producing aggregates weighing from 2 to 16 lb per cu ft. Geology Perlite is one of the large family of rocks originating from a granitic or acidic magma and generally has a "rhyolitic composition with a marked perlitic structure."² The name "perlite" is a derivation from "perlstein" originally given "to certain glassy rocks (hyaloliparites, hyalo-rhyolites) with numerous concentric cracks, from the fancied resemblance of broken out fragments to pearls."3 The cause of the perlitic texture is somewhat controversial. Johannsen attributes the texture to strain set up in the glass by cooling and describes the finding of peculiar, glassy balls, called marekanite, more or less rounded and showing concave indentations, which may be left when perlite is broken. Frank Rutley, on the other hand, in 1881, while working on vitreous rocks from Montana, observed that there was incipient or partially started crystallization with segregation of water toward the un-crystallized portion in all specimens of perlite examined. Further he observed evidence of strain around focii of crystallization to which he ascribed the development of the spherical cracking which gives the rock its perlitic texture.4 Widespread over the western and southwestern United States where Tertiary vulcanism is exposed, perlite commonly is associated with andesitic, basaltic, and rhyolitic lavas with inter-bedded tuffs and ash of Eocene age although some deposits are associated with rocks assigned to the Pliocene age.5, 6 n nearly all cases the perlite overlies water laid tuff beds or agglomerates or breccias of explosive nature, an outstanding exception being the occurrence of perlite as the chilled selvage of andesite intrusions.7&apos;8 Available chemical analyses of per-lites from the western and southwestern United States indicate that they are varieties of leucorhyolites rather than of normal rhyolites, leucorhyolites having less than 5 pct of dark minerals, normal rhyolites having more than 5 pct. This conforms with Johannsen&apos;s observation that leucorhyolites are the prevailing kind in North America.9 Tables 1 and 2 give

Jan 1, 1950

By Samuel Hoyt

THE hardness of annealed copper has been given in the literature and is easily obtained by any of the standard methods of hardness testing. It is not our intention to correct published values or to add to them, but to describe tests of two bars of annealed electrolytic copper in which the methods of Meyer&apos;s analysis were employed. MEYER&apos;S ANALYSIS OF BALL INDENTATION TEST The ball indentation test is probably the most valuable hardness test we now have but, as it is carried out in the Brinell or Rockwell test, the result may be seriously in error without the operator suspecting such to be the case. This condition results from the isolated and uncontrolled nature of the measurement. The accuracy depends on the accuracy of the equipment and the care and skill used in the operations; there is nothing in the impression diameter, which is all that is measured, to indicate the presence of error. Meyer&apos;s analysis supplies a control of the measurements that goes far toward eliminating unsuspected errors. The principles of this work maybe obtained from elsewhere.1 As this subject has not received the attention of this Institute, it may be well to summarize the more important points as follows.

Jan 2, 1926

By Charles Camsell

MORE than one-third of all Canada is embraced in the federal domain known as the Northwest Territories. Its most northern point, Cape Columbia, on Ellesmere Island, is only 500 mi. from the Pole. It includes parts of the main physiographic divisions of the North American continent. In the West there is a strip of 30.000 sq. mi. lying in the Cordilleran region, where peaks in the Mackenzie Mountains rise as high as 8500 ft. East of this strip and extending roughly to a line through Great Bear and Great Slave lakes to the Arctic coast is a section of the interior plains. This section, known as the Mackenzie Lowlands, contains the great artery, the most striking feature of the Northwest Territories-the Mackenzie and Slave river waterway impressive in its width, almost two miles in places, and in it&apos;s navigability for 1357 miles without obstruction to the sea. Adjoining the Mackenzie Lowlands on the East is the greater portion of the mainland of the Territories, which, as well as a large share of the island area, is in the Canadian Shield.

Jan 1, 1937

By A. Lee Barrett

MINE power systems are quite different in many respects from those usually found in industrial plants. Wide areas are served, usually by a circuit which is connected continuously throughout the mine. In some mines one circuit may run for several miles. There are usually a small number of branch circuits involved considering the areas covered. In all mines circuits are sectionalized at approximately 2500 ft by means of switches. All, or at least most branch circuits, are sectionalized by manual switches. In some mines automatic sectionalizing gear is used to give automatic overload protection at various strategic points in the system. However at the present time this practice is by no means general. Circuit hazards in mine electric systems are much greater than those encountered in industrial installation. Falls of roof or coal form a prominent hazard which may break the wire and may cause ground faults or partial ground faults. Ordinarily electric cables in mines cannot be insulated, there- fore n fall can easily cause a short circuit. The humidity in most mines is greater than 95 pct and at many points the floor is wet and water may be dripping from the roof over insulators, increasing the difficulties at that point. All electrical circuits must be contained in the mine entries and space must also be provided for moving equipment and men. Consequently, because of the proximity of the power circuit to the locomotives and other moving equipment a considerable hazard is introduced. Mine haulage track is not always good so that wrecks are not unusual. A wreck frequently does consider- able damage to the power circuit. A ground fault frequently results in heavy arcing which may be sustained. If the damage to the circuit is mechanical it may mean that a trip of coal has wrecked and a great deal of coal dust could be thrown into the air as a result of the wreck. The arc resulting from the ground fault could ignite the coal dust and a mine explosion would result. A continued ground fault, even if high in resistance, also may ignite the coal which may be on the bottom of the entry and a mine fire may result. The fire hazard is one of the most serious hazards in any coal mine. Since the mine circuit is completely interconnected, any power interruption resulting from a fault seriously affects the whole operation. Unless the mine is completely sectionalized the whole mine will be shut down until the fault is located and the proper switches are opened to isolate the fault; even then large areas may still be without power if they are supplied by a single power circuit which may be opened in isolating the fault. Further, mine power is usually supplied from a relatively small number of substations and the fault may be on a stub feed circuit, in which case power cannot be restored until the fault has been cleared. Practice varies widely with respect to placement of substations. Usually they will be spaced from I to 2 miles in 500V operations, and at 1 mile intervals or less, in 250 V operation. Actual mining operations govern substation placements and no general rules can be followed.

Jan 1, 1948

By J. B. Austin

In considering so complex a process as the smelting of iron in the blast furnace, there is obviously no single method of calculating efficiency that gives a complete appraisal of the performance of the furnace in all its several functions; such a comprehensive view as is required to evaluate producing ability and manufacturing costs for a given furnace is obtained only by considering a group of efficiencies, each of which measures the performance of the furnace from a specific point of view. For instance, there is the rate of consumption of coke per ton of iron produced, which is probably the most frequently considered, and is certainly one of the most important of the group; there is the efficiency of recovery of iron charged; and there is the efficiency of utilization of energy, both chemical and thermal, in some respects related to the former two yet in other ways independent of either. In each of these cases, the calculation can be made on the basis of the actual input of material or energy, or it may be based upon a comparison with the minimum amount of material or energy that would be required by a "perfect" furnace; that is, an imaginary ideal furnace analogous to the perfect steam engine used in thermodynamic calculations, when this furnace is operating under optimum conditions. Moreover, the furnace itself can be considered either as an apparatus for smelting iron or, taking a somewhat less common point of view, as a gas producer yielding iron and slag as by-products. Some of these efficiencies are more useful than others, yet all are instructive; for a knowledge of them not only leads to good engineering practice from the standpoint of control but also discloses limits to possible improvement in performance and indicates the lines along which improvement is most likely to be profitable. Estimates of some of these efficiencies have appeared from time to time in the literature, but many of them are open to objection because they are based on data of uncertain accuracy or because they have been caleulated without due regard to the thermodynamic principles involved. Moreover, so far as the author is aware. no general survey of the blast furnace comparing its performance in all the aspects mentioned has been made.

Jan 1, 1938

By J. B. Austin

In considering so complex a process as the smelting of iron in the blast furnace, there is obviously no single method of calculating efficiency that gives a complete appraisal of the performance of the furnace in all its several functions; such a comprehensive view as is required to evaluate producing ability and manufacturing costs for a given furnace is obtained only by considering a group of efficiencies, each of which measures the performance of the furnace from a specific point of view. For instance, there is the rate of consumption of coke per ton of iron produced, which is probably the most frequently considered, and is certainly one of the most important of the group; there is the efficiency of recovery of iron charged; and there is the efficiency of utilization of energy, both chemical and thermal, in some respects related to the former two yet in other ways independent of either. In each of these cases, the calculation can be made on the basis of the actual input of material or energy, or it may be based upon a comparison with the minimum amount of material or energy that would be required by a "perfect" furnace; that is, an imaginary ideal furnace analogous to the perfect steam engine used in thermodynamic calculations, when this furnace is operating under optimum conditions. Moreover, the furnace itself can be considered either as an apparatus for smelting iron or, taking a somewhat less common point of view, as a gas producer yielding iron and slag as by-products. Some of these efficiencies are more useful than others, yet all are instructive; for a knowledge of them not only leads to good engineering practice from the standpoint of control but also discloses limits to possible improvement in performance and indicates the lines along which improvement is most likely to be profitable. Estimates of some of these efficiencies have appeared from time to time in the literature, but many of them are open to objection because they are based on data of uncertain accuracy or because they have been caleulated without due regard to the thermodynamic principles involved. Moreover, so far as the author is aware. no general survey of the blast furnace comparing its performance in all the aspects mentioned has been made.

Jan 1, 1938

Secondary minerals are the result of a process of concentration and enrichment and are commonly richer than the primary minerals of the same deposit. Secondary ores that contain abundant sulphides are commonly distinguishable in the field from primary ores; this distinction is more difficult with ores that carry a small quantity only of sulphide minerals, and microscopical examination of the ore in thin section is advisable in all doubtful cases. It is frequently difficult, and in some cases impossible, to determine the primary or secondary character of quartzose gold ores. The safest guide is the presence or absence of gaseous or fluid inclusions in association with the ore minerals; such primary association coupled with a lack of traces of oxidation is indicative of primary origin. Any ore that carries traces of oxidation, such as iron stains, endritic oxides of manganese, kaolin and so forth must be considered to have been acted upon by surface agencies, and secondary enrichment must be suspected. Further examination, however, may indicate that the contained value is primary, and, therefore, persistent in its vertical distribution. The manner of occurrence of secondary minerals is frequently characteristic; secondary minerals, being due to the action of surface waters, are commonly found in cracks through earlier minerals, or as crusts lining vugs or surrounding nucleal masses, or in general, in some distribution later than and not conforming to the arrangement of the primary minerals. Secondary sulphides are often found as soft black pulverulent masses or coatings, although they frequently occur well crystallized or as

Jan 1, 1932

By E. N. Smith, J. C. Redmond

The increasing need for materials capable of withstanding higher operating temperatures for various applications such as gas turbine blading and other parts, rocket nozzles, and many industrial applications, has brought consideration of cemented carbide compositions. The well known usefulness of cemented carbides as tool materials is attributable to their ability to retain their strength and hardness at much higher temperatures than even complex alloys. However, it has been found that the temperatures encountered in cutting operations do not approach by several hundred degrees1 those involved in the applications mentioned above where the interest is in materials possessing strength and resistance to oxidation at temperatures of 1800°F and above. At these latter temperatures, the tool type compositions which are made up essentially of tungsten carbide are found to oxidize very rapidly and to produce oxidation products of a character which offer no protection to the remaining body. As a further consideration, the density of the tungsten carbide type compositions is high, from about 8.0 to 15.0. The refractory metal carbides as a class are the highest melting materials known as shown by Table 1 which summarizes the available data from the literature for the carbides of the elements which are sufficiently available for consideration for these uses. The density is also included in the table, since as mentioned above it is an important consideration in many of the applications for which the materials would be considered. It has been established that in the tool compositions the mechanism of sintering with cobalt is such as to result in a continuous carbide skeleton and that the properties of the sintered composition are thus essen- tially those of the carbide.2 On the hypothesis that this mechanism holds to a greater or less degree in cementing most of the refractory metal carbides with an auxiliary metal, it appears from Table 1 that titanium carbide compositions would offer possibilities for a high temperature material. Titanium carbide has extensive use for supplementing the properties of tungsten carbide in tool compositions. Although the literature contains several references to compositions containing only titanium carbide with an auxiliary metal,3,4,5,6 it may be inferred from the meager data that such compositions were deficient in strength and were considered to have poor oxidation resistance.7 Kieffer, for instance, reports the transverse rupture strength of a hot pressed TiC composition at 100,000 psi as compared to up to 350,000 psi for WC compositions. The work described herein was undertaken to determine the properties of compositions consisting of titanium carbide and an auxiliary metal and to improve the oxidation resistance of such compositions. It appeared possible that the inclusion of one or more other carbides with titanium carbide might improve the oxidation resistance and also that this might be more desirable than other means from the point of view of maintaining the highest possible softening point. Consideration of the available carbides in Table 1 suggests tantalum and columbium carbides because of their high melting points and general refractoriness. The work on improving oxidation resistance was concentrated on the addition of tantalum carbide or mixtures of tantalum and columbium carbide. The auxiliary metals used included cobalt, nickel and iron. It was also desired to learn the general physical properties of these compositions. Experimental Procedure The compositions used in this study were made by the usual powder metallurgy procedure applicable to cemented tungsten carbide compositions. The powdered carbide or carbides and auxiliary metal were milled together out of contact with air. In some cases cemented tungsten carbide balls and in other instances steel balls were used to eliminate any effect of tungsten carbide contamination. A temporary binder, paraffin, was then included in the mix and slugs or ingots were pressed with care to obtain as uniform pressing as possible. The ingots were presintered and the various shapes of test specimens were formed by machining, making the proper allowance for shrinkage during sintering. Thereafter the shapes were sintered in vacuum at temperatures of from 2800 to 3500°F. Final grinding to size was carried out by diamond wheels under coolant. The titanium carbide used contained a minimum of 19.50 pet total carbon and a total of 0.50 pet metallic impurities as indicated by chemical and spectrographic analysis. It was found by X ray diffraction examination with

Jan 1, 1950

Jan 1, 1951

Jan 1, 1951

By H. W. Winkler, Discussion, V. L. Forsyth

The development of a new gar lift valve has removed many of the obstacles limiting over-all gas lift efficiency. The valve is pressure charged in place in a well, and operating pressure can be changed without pulling. Temperature and gas gradient compensation have been eliminated. Intermitting and constant flow installations, using conventional pressure-charged valves, are compared with designs incorporating the new automatic stabilizer controlled valve. Specific well performance data are presented. The means of obtaining and controlling multiple-point injection of gas are explained and contrasted with single point injection. The effect on small diameter strings and multiple string installations is discussed. The effect of flowing temperature gradient on a design using conventional pressure-charged valves, the limitations imposed by such temperature, and the obvious benefits which result from the use of automatic stabilizer controlled valves are shown. Reduction of gas requirements is stated mathematically and demonstrated with specific examples which are identified as to oil company and well. Increased fluid recovery resulting from greater drawdown is illustrated. The economic advantages are mentioned with emphasis on reduction of capital expenditures, as well as reduction in operating expenses. INTRODUCTION Much of the engineering and research work performed with gas lift has been based upon the supposition that under producing conditions gas would be injected at a single point in a well. Many tests were performed in determining the optimum size of the opening through which gas would be passed and the exact placement of the valve equipment. The objectives in a gas lift installation are to unload the well and to efficiently produce the well after it is unloaded. Until recently, the function of upper valves was simply to unload the well. An operating valve located at a proper place in a well served as a single injection point for lifting liquid to the surface. The basic problem in using such equipment is to arrive at operating depth with sufficient operating pressure to efficiently lift the liquid. Few gas lift installations are designed with all required well data available. However, regardless of the quality and availability of data, and regardless of the accuracy of the design, there is the practical problem of preparing and placing gas lift equipment in the well in exact accordance with the plans and intentions of the engineer. In recognition of these and many other problems, attention was directed toward a means of removing the need for temperature and gas gradient compensation, a way to change the gas lift installation to meet the changing requirements of the well itself, and a manner of compensating for changes in oil-water content, fluid volumes, PI, and bottom-hole pressure resulting from flood or repres-suring activity. A device which could actually set and change the operating pressure of gas lift valves in the well would meet most of these needs. There now exists a new gas lift valve which fulfills the original objectives and in so doing actually accomplishes much more. With this device, called an Automatic Stabilizer Controlled valve, there is an exact matching of valve operating pressure and well conditions. Gas is injected at more than one point in the well, thereby making controlled multiple-point injection of gas a reality. Installation calculations are materially simplified and the need for basic temperature and gas gradient data no longer exists. Section I—The Automatic Stabilizer Controlled Valve The operation of the ASC valve is more easily understood by first studying a conventional pressure-charged valve and then inserting the stabilizer element to observe the changes which result. Fig. 1 is a schematic of a conventional precharged pressure-operated valve. The pressure in the dome pd, acts downward, against the area of the bellows A,, to hold the valve closed. The resulting force Bf plus the spring effect of the bellows Sf represents the total force acting to close the valve. Correspondingly, the tubing pressure ptbg works upward against the port area Atbg and the casing pressure pc works upward against a portion of the area of the bellows

Jan 1, 1965

By Orville R. Lyons, A. C. Richardson

F. X. Ferney—We are pleased that this paper was presented at this meeting and thank Mr. Richardson and Mr. Lyons for their effort and work in preparing it. We agree with the authors that it was unfortunate that more comprehensive data were not available when the paper was prepared, this being particularly true since we had no knowledge that the paper was being written and could not make available data which were in our process files. Further, it is our opinion that because the data are not sufficiently comprehensive the results which are presented are erratic and will lead to false conclusions. As we see it, there are three Specific reasons why the data which are presented cannot be considered accurate. 1. The preparation plant was not at equilibrium while the samples were being taken. This is indicated by the fact that the percent of solids in the circulating water varied from 3.9 pct to 10.7 pct during the period when the plant was sampled. 2. We do not believe that the samples of Bird feed which were taken were representative and could indicatc the true feed to the filter. Evidence of this is shown in the data where the dewatered product leaving the centrifuge contains more coarse material than the feed to it, that is, material which is +6-mesh in size. 3. We question if the data concerning screen analysis in the fine sizes is accurate and would conclude (from the data) that these tests were made by a dry-screen method. We have found that wet screening is always necessary to obtain a true picture of the quantity of —200-mesh fines which is present. The test work described in the Lyons-Richardson paper was conducted some time ago and the tests were carried on during a period when the preparation plant had not ironed out all of their start-up problems. Since that time most of these problems have been corrected and now this is a smooth running, well-operated prep-

Jan 1, 1951

By Orville R. Lyons, A. C. Richardson

F. X. Ferney—We are pleased that this paper was presented at this meeting and thank Mr. Richardson and Mr. Lyons for their effort and work in preparing it. We agree with the authors that it was unfortunate that more comprehensive data were not available when the paper was prepared, this being particularly true since we had no knowledge that the paper was being written and could not make available data which were in our process files. Further, it is our opinion that because the data are not sufficiently comprehensive the results which are presented are erratic and will lead to false conclusions. As we see it, there are three Specific reasons why the data which are presented cannot be considered accurate. 1. The preparation plant was not at equilibrium while the samples were being taken. This is indicated by the fact that the percent of solids in the circulating water varied from 3.9 pct to 10.7 pct during the period when the plant was sampled. 2. We do not believe that the samples of Bird feed which were taken were representative and could indicatc the true feed to the filter. Evidence of this is shown in the data where the dewatered product leaving the centrifuge contains more coarse material than the feed to it, that is, material which is +6-mesh in size. 3. We question if the data concerning screen analysis in the fine sizes is accurate and would conclude (from the data) that these tests were made by a dry-screen method. We have found that wet screening is always necessary to obtain a true picture of the quantity of —200-mesh fines which is present. The test work described in the Lyons-Richardson paper was conducted some time ago and the tests were carried on during a period when the preparation plant had not ironed out all of their start-up problems. Since that time most of these problems have been corrected and now this is a smooth running, well-operated prep-

Jan 1, 1951

By A. Lee Barrett

Mine power systems are quite different in many respects from those usually found in industrial plants. Wide areas are served, usually by a circuit which is connected continuously throughout the mine. In some mines one circuit may run for several miles. There are usually a small number of branch circuits involved considering the areas covered. In all mines circuits are sectional-ized at approximately 2500 ft by means of switches. All, or at least most branch .circuits, are sectionalized by manual switches. In some mines automatic sectionalizing gear is used to give automatic overload protection at various strategic points in the system. However at the present time this practice is by no means general. Circuit hazards in mine electric systems are much greater than those encountered in industrial installation. Falls of roof or coal form a prominent hazard which may break the wire and may cause ground faults or partial ground faults. Ordinarily electric cables in mines cannot be insulated, therefore a fall can easily cause a short circuit. The humidity in most mines is greater than 95 pct and at many points the floor is wet and water may be dripping from the roof over insulators, increasing the difficulties at that point. All electrical circuits must be contained in the mine entries and space must also be provided for moving equipment and men. Consequently, because of the proximity of the power circuit to the locomotives and other moving equipment a considerable hazard is introduced. Mine haulage track is not always good so that wrecks are not unusual. A wreck frequently does considerable damage to the power circuit. A ground fault frequently results in heavy arcing which may be sustained. If the damage to the circuit is mechanical it may mean that a trip of coal has wrecked and a great deal of coal dust could be thrown into the air as a result of the wreck. The arc resulting from the ground fault could ignite the coal dust and a mine explosion would result. A continued ground fault, even if high in resistance, also may ignite the coal which may be on the bottom of the entry and a mine fire may result. The fire hazard is one of the most serious hazards in any coal mine. Since the mine circuit is completely interconnected, any power interruption resulting. from a fault seriously affects the whole operation. Unless the mine is completely sectionalized the whole mine will be shut down until the fault is located and the proper switches are opened to isolate the fault; even then large areas may still be without power if they are supplied by a single power circuit which may be opened in isolating the fault. Further, mine power is usually supplied from a relatively small number of substations and the fault may be on a stub feed circuit, in which case power cannot be restored until the fault has been cleared. Practice varies widely with respect to placement of substations. Usually they will be spaced from I to 2 miles in 500V opera-tions, and at I mile intervals or less, in 250V operation. Actual mining operations govern substation placements and no general rules can be followed.

Jan 1, 1949

By Mark Malamphy

DURING colonial times, Brazil was famous for the richness of her alluvial gold deposits. Paul Ferrand has estimated that the gold produced during the period from 1700 to 1820 was the equivalent of some 64 million pounds sterling. Since that time, most of the more prolific alluvial deposits have been exhausted. A few gold mines are still func-tioning, notably the Morro Velho mine, which is one of the deepest mines in the world. Today, the gold production of Brazil is insignificant when compared with world figures, but there are still many gold-bearing regions and it is probable that in at least some of them profitable returns would result from an exploitation program taking advantage of all the most modern innovations in gold mining and ore treatment on a large scale. In order to demonstrate the value of some of these abandoned pros-pects and stir up interest in increasing the national gold production, the government has stimulated research. Experimental plants have been and are being established in various places, and tests on large quantities of ores are being carried out on a semicommercial basis. The Geological Survey of the State of Minas Geraes is very active in this line and the Federal Institution is also showing an increased interest in the matter. One of the lesser known gold-bearing regions of Brazil is in the vicinity of Lavras, in the State of Rio Grande do Sul. Gold was first reported from this region in the early part of the nineteenth century. In 1811, D. João VI sent an experienced prospector from Minas Geraes to investi-gate the validity of the reports. According to the reports of Baron

Jan 1, 1934

By Harold V. Pearce

(Chattanooga Meeting, October, 1908.) THE fire which occurred in the fall of 1906, at the works of the Boston & Colorado Smelting Co., Argo, Colo., destroyed entirely the gold- and silver-refinery of the plant; and in view of the development of modern practice in the refining of copper-mattes, etc., the management decided that it would be inadvisable to rebuild that part of the works for the continued use of the process which had been conducted therein for so many years as a metallurgical secret. This decision probably removes altogether from the sphere of practice the " Pearce " method for the separation of gold. At all events, it removes the business reasons which have prevented hitherto the publication of the principles involved. At the suggestion of Dr. Raymond, Secretary of the Institute, my father, Richard Pearce, the former manager of these works, has requested me to prepare a brief description of this process for the benefit of our members. Since I severed my connection with the Boston & Colorado Smelting Co. some time ago, I am indebted for some practical details to the present superintendent, Charles Rees, whose friendly assistance I would gratefully acknowledge. With regard to the history of the inception and development of this process by its inventor, Richard Pearce, I cannot do better than quote freely from his own notes and papers. HISTORY OF THE PEARCE PROCESS.&apos; "In 1874 my entire time was directed to the improvements and additions to the plant at Black Hawk. The changes which I had made in the construction of the furnaces at Black Hawk proved so beneficial that I was requested to introduce the improvements at the branch works at Alma. These changes were carried out as speedily as possible, and proved of great advantage as compared with the old system. "The separation and refining of the gold from the matte now engaged my attention, and since previous experience in the treatment of gold-bearing matte and

Feb 1, 1909

By George W. Toth

This paper describes the features of a computer cost model developed to estimate requirements and costs of individual coal mining projects. Detailed cost analysis procedures for both coal mining and preparation are incorporated into the model. This model has been developed over a period of seven years through funding provided by the Electric Power Research Institute (EPRI). The model follows a process engineering approach for the estimation of all project capital and operating costs. A discounted cash flow analysis procedure is also designed into the model to allow for the solution of cost/ton or cost/MMBtu of clean coal production. The model can be applied to most surface or underground mining deposits and can accommodate a wide variety of coal washing situations. This flexibility makes the model a particularly useful tool for preliminary project analysis, property screening, investment analysis, mining technology assessment, coal cleaning level assessment, and general property valuation.

Jan 1, 1983

By R. A. Ritter, J. P. Batycky

A numerical technique has been developed to permit estimating the pressure gradient associated with laminar flow of thixotropic liquids through long Pipelines. For this purpose the pipeline is divided into a number of radial and longitudinal increments within which rheological properties of the fluid may be considered as constant at any time. Then, provided only that the fluid flow curve is defined at every duration of shear, it is possible to predict the instantaneous pressure gradient at any cross-section along the pipeline for each desired flow rate and pipe size. The technique consists of an iterative integration of shear rate to establish the appropriate value of the wall shear stress at each location. Consistency of fluid in the increment is determined by the flow history of that increment, while the radial flow associated with variations in velocity profile is accounted for by adjusting the width and radial position of the increment. A number of pressure profiles, computed at each of several flow rates, provide a convenient basis for pipeline design and pump selection. INTRODUCTION In recent years considerable attention has been given to predicting pressure drop associated with the isothermal laminar flow of time-independent non-Newtonian fluids in pipes and annuli. 6,11,12 The approach generally has been to develop analytical relationships between flow rate and pressure drop based on simple constitutive models which hopefully provide an approximate description of the rheological properties of the fluid. Analytical solutions are highly desirable since the influence of all pertinent parameters can be readily determined. Unfortunately, however, this approach is restricted to simple flow geometries and- frequently leads to erroneous results due to inadequacies in the model. In certain cases a solution may be obtained through applying appropriate numerical techniques.l,14 For example, a digital computer program is available for predicting the velocity profile and pressure drop encountered by any Newtonian or time-independent non-Newtonian fluid flowing under laminar conditions in a cylindrical pipe or annulus.l In this paper the consistency behavior of the fluid need only be described in terms of basic rheological data. Analyzing flow systems involving fluids with time-dependent rheological characteristics is considerably more complicated since substantial changes in consistency may occur because of sustained shear action. This sensitivity to shear frequently persists for several hours. Consequently, variations in pressure drop and/or flow rate resulting from the aging process and addition of unsheared or partially sheared fluid to the system must be considered for purposes of pipeline design. This paper outlines a numerical method for predicting the transient and steady-state laminar flow behavior of a thixotropic liquid in a pipeline of arbitrary length (i.e., at a specified constant flow rate, the instantaneous pressure gradient may be determined at any time after start up and at any location along the pipeline). Several such pressure gradient profiles, computed at several flow rates, may be combined to produce a complete portrait of the system response. This flow portrait provides a reasonable basis for pipeline design and for selecting a suitable pump characteristic. TIME-DEPENDENT RHEOLOGICAL BEHAVIOR The most familiar time-dependent rheological properties are those exhibited by thixotropic liquids. Many of these materials, particularly thixotropic crude oils, generally display an apparent yield stress in that a finite pressure gradient is required to initiate flow. Then, under the influence of sustained shear at a constant shear rate, the consistency systematically decreases to some final limiting value. The shear stress obtained at