Search Documents

By R. W. Fountain, W. D. Forgeng, G. M. Faulring

Precipitation of the phase Co3Ti (Cu3Au type) from a Co-5 pct Ti a11oy has been investigated using single-crystal X-ray diffraction techniques. Oscillation and transmission Laue patterns of specimens aged for short-time periods at 600" C indicate the formation of titanium-rich and titanium-poor zones coherent with the {100} matrix planes. Longer aging times at 600° C establish that the equilibrium phase also forms on the {100} matrix planes as platelets. These observations are corroborated by electron metallography; electron diffraction studies show the phase Co3Ti to be ordered. A probable sequence of the precipitation reaction is discussed. A previous publication by two of the present authors reported on the phase relations and precipitation in Co-Ti alloys containing up to 30 pct Ti.1 The results of this investigation established the existence of a new face-centered cubic inter metallic phase, ranging in composition from about 17.0 to 21.7 pct Ti at temperatures below 1000° C The decomposition of the fcc supersaturated solid solution was studied employing hardness and electrical resistivity measurements. The changes in hardness upon precipitation in alloys containing 3, 6, and 9 pct* Ti were found to be associated with an initial increase in hardness followed by a plateau and then a second, more pronounced hardness increase. Investigation of this behavior by electrical resistivity measurements suggested that two different kinetic processes were involved, which, when interpreted in terms of the kinetic relation,2-4 indicated that initial precipitation was in the form of thin plates. On continued aging, the plates impinged during the growth process. The general features of these findings have been confirmed by Bibring and Manenc,5 while, in addition, they report the phase to be ordered. The present investigation was undertaken to provide more definite information on the structural relationships between the precipitate and the matrix. EXPERIMENTAL PROCEDURE Single crystals of a (20-5 pct Ti alloy were prepared from the melt employing the Bridgman technique. Poly crystalline rod, 1/2 in. in diam, prepared from vacuum-melted material, was machined to 3/8- in. diam to remove any surface contamination that may have resulted from hot-working. The crystals were grown under a purified hydrogen atmosphere in high-purity alumina crucibles heated by induction. Considerable difficulty was encountered in attempting to grow monocrystals because of the high melting point of the alloy and the high solute concentration. However, one crystal about 6 in. long was obtained which was essentially a single crystal except for one or two very small grains around the periphery. The as-grown crystal was solution heat-treated for 24 hr at 1200°Cin a purified argon atmosphere and water-quenched. One-quarter-in. slices were taken from each end of the solution heat-treated crystal for chemical analyses, and the remainder of the crystal was mounted and oriented by the back reflection Laue Method. The chemical analysis of the crystal was as follows: Pct Ti Pct 0 Pct C Pct N Pct H Pet CO 5.29 0.08 0.004 0.002 0.0003 Balance By proper tilting of the crystal, it was possible to obtain slices 1/32 in. thick of [loo] and [110] orientation. The solution heat-treated crystal slices were sealed in silica capsules for the aging treatments, with titanium sponge placed at one end of the capsule to act as a getter. All slices were water-quenched from the aging temperatures, the capsules being broken under the water to ensure a rapid quench. Thinning of the slices for transmission X-ray studies was accomplished by a combination of mechanical and electrolytic techniques, the final thickness being about 0.1 mm. Laue patterns of the solution heat-treated crystal indicated that no strain was introduced by the thinning technique. ELECTRON METALLOGRAPHY After X-ray examination, the structural changes attending the precipitation were followed by examination of direct carbon replicas of polished and etched surfaces of the single-crystal slices and extracted phases. The earliest indication of significant structural change was observed after aging at 600°C The structure of a heavily etched, solution-treated crystal is shown in Fig. l(a). Aside from the etch pit pattern, no regularity of background structure is observed. On the other hand, in the background of the specimen heated for 500 hr at 600°C, the etching pattern shows a directionality indicating the influence of minute precipitate particles, Fig. l(b). On electrolytic dissolution of this specimen in 10 pct HC1 in alcohol, a large volume of very small, flattened cubes

Jan 1, 1962

By E. C. Roberts

TO facilitate some recent microscopic investigations it was necessary to devise special mounting techniques for the polishing of two quite different metallographic specimens. These techniques are extremely simple and are submitted for whatever value they may be to other investigators. The first specimen mount proved very satisfactory for the study of untempered martensite. Since it was undesirable to heat the specimen, lucite or bakelite mounting materials could not be used in the conventional manner. A cold mount was made by drilling a hole of the same diameter as the specimen in a cylindrical piece of polystyrene then press- ing the steel specimen into the hole on an ordinary vise. A prefabricated disk of lucite should work equally well. The only precautions necessary are that the hole be drilled out cleanly and the piece of steel be pressed into the plastic uniformly, otherwise the mount will crack. The second type of mount was required for the study of slag specimens by reflected light. Mounting these specimens in bakelite and then attempting to rough finish the surfaces on graded emery papers resulted in a considerable amount of chipping and breaking out of the slag particles. This made further satisfactory polishing almost impossible. It was found, however, that if the bakelite-mounted specimen was first rough finished to a point where a good specimen surface became visible, the interstices in the specimen surface could be filled and the polishing completed. This filling was accomplished by placing a small amount of lucite powder in the bottom of the steel specimen mold then reinserting the bakelite-mounted specimen on top of the lucite powder. Reheating the mold to the proper temperature and applying the required pressure resulted in the formation of a thin disk of lucite on the bottom of the bakelite specimen. By carefully grinding the lucite away a uniform surface including the slag specimen was obtained and further polishing was unhampered by slag disintegration.

Jan 1, 1951

By R. M. Waterstrat, E. C. van Reuth

BINARY- alloy phases having the A15-type crystal structure have been described as occurring at a simple and more or less invariant stoichiometric composition (A3B) which corresponds to the relative number of atoms occupying each of the two crystallographi lattice sites in this structure.1,2 It is frequently assumed, therefore, that each crystallographic site is occupied exclusively by one kind of atom. In most cases, however, there have been insufficient experimental data to establish whether atomic ordering is, in fact, complete. Recent studies have shown that binary A15-type phases are sometimes stable over an appreciable composition range3''* and, occasionally, the composition range of stability does not even include the "ideal" A3B stoichiometric composition.5-7 We have observed the existence of nonstoichiometric A15-type phases in the binary systems Cr-Pt and Cr-Os. This has not been reported in previous work on these alloy systems.1,8-11 A series of alloys, each weighing approximately 30 g, was prepared by are-melting in an Ar-He atmosphere using 99.999 pct Cr, 99.999 pct Os, and 99.99 pct Pt as starting materials. Each alloy was melted four times with a total weight loss of less than 1 pct. The stoichiometric (A3B) alloys were sealed in evacuated quartz tubes and annealed at 1200°C for periods of time ranging from 3 days to 2 months. Examination of the alloy microstructures revealed that little change had occurred over this time interval and it was therefore assumed that the microstructures were fairly representative of equilibrium conditions. No evidence of contamination was observed although there was apparently some loss of chromium which was confined to a thin layer at the surface of the specimens. The quartz tubes were quenched from the annealing temperature into cold water. X-ray diffraction and metallographic examination of the stoichiometric alloys revealed an estimated 10 to 30 pct of second phases which were tentatively identified as phases previously reported in these binary-alloy systems.8-11 A second series of alloys was prepared by mixing -325 mesh metal powders having a nominal purity of 99.9 pct and compressing these mixed powders in a cylindrical die at a pressure of 43,000 psi. These alloys, each weighing 15 g, and some of the arc-melted alloys were annealed in a high-temperature vacuum furnace heated by tantalum strips at a pressure of 10-8 Torr and were rapidly cooled by turning off the furnace power. X-ray and metallographic examination of both series of alloys served to establish the composition ranges of the A15-type phases. Although some chromium losses occurred during the vacuum annealing, they were largely confined to a thin layer on the outer surfaces of the samples. It was established that the A15 phases occur in the Cr-Pt system at 21 ± 1 at. pct Pt after 1 week at 1200°C and in the Cr-Os system at 28 ± 1 at. pctOs after 1 day at 1400°C (see Table I). We also observed that an arc-melted stoichiometric (A3B) alloy in the Cr-Ir system was single-phase (A15-type) in the "as-cast" condition in agreement with previous work.8,13 In addition we obtained a sample of the Cr-Os A15-type phase from Argonne National Laboratory. This alloy contained less than 1 pct second phase12 and was submitted to a density measurement. The density measurement yielded a value of 11.14 g per cu cm in comparison to a theoretical value of 11.25 g per cu cm calculated using the observed lattice constant (4.6806Å) of this alloy. The uncertainty in measurement was 0.1 pct but the sample may have contained some cracks or minor imperfections which could account for the low experimental value. We have also studied the atomic ordering in these phases by means of integrated line intensity measurements using thick, flat, rotating powder samples and CuK a radiation in an X-ray diffractometer. We have obtained order parameters of 0.90 for the Cr-Pt phase, 0.89 for the Cr-Ir phase, and 0.64 for the Cr-Os phase using the formula: where s is the usual Bragg and Williams order parameter, ra is the fraction of chromium atoms in A sites, and FA is the fraction of chromium atoms in the alloy. The values obtained are estimated to be accurate within ±4 pct. If the unusually small value for the order parameter of the Cr-Os A15 phase were due to the existence of lattice vacancies on the "B-atom" sites, then a density of 10.04 g per cu cm would be expected in contrast to the observed value of 11.14 g per cu cm. We, therefore. conclude that the fraction of lattice vacan-

Jan 1, 1967

By Hans Lundberg

Jan 1, 1927

By Harry C. Swanson

TRANSPORTING concrete from mixer to forms has always been a problem. Twenty-five years ago this task was generally accomplished by means of wheelbarrow or concrete buggy. On large dam jobs, as the number of these projects increased, the gantry crane or highline came into use. Today several methods of handling concrete are employed on smaller surface construction jobs, for example, transit-mix trucks or dumpcrete trucks, which have crawler cranes with buckets for placing concrete into forms. In 1944, during early stages of developing Mather mine A shaft, several large underground concrete jobs were necessary. At this time the Cleveland-Cliffs Iron Co, purchased the first pump-crete machine, introduced by the Chain Belt Co. of Milwaukee. The machine was used to pour approximately 200 cu yd of concrete for a dam, or bulkhead, located 400 ft from the shaft. Concrete was mixed on surface, lowered down the shaft 1000 ft in a 2-cu yd bucket hung under one skip, spouted into the bowl of the pumpcrete machine from the bucket, and pumped directly into the forms. Since the day of the first pipeline concrete in 1944 to the present time, other equipment and other methods have been developed to permit transportation of concrete by pipeline through vertical and horizontal distances totaling 1 mile from mixer to forms. Much of the efficiency in present handling of underground concrete can be credited to the Bethlehem Cornwall mines, where concrete was transported through 6-in. pipe for great distances down an inclined shaft and along levels into forms.' During initial development of Mather mine B shaft, with concrete work under way on two or more levels at one time, the pneumatic concrete placer, Fig. 1, was selected as best adapted for underground concrete transportation. The 3/4-cu yd pneumatic placer is a small machine readily moved from one location in the mine to another. It can be equipped with two sets of mine car wheels, which will permit moving on regular mine tracks. It is therefore possible to send concrete through the pipe at great velocity; the pipeline is clean after each shot except for the film of cement adhering to the inside. With the proper slump in the concrete, it is possible to shoot concrete 2000 ft with this machine, using the mine supply of compressed air at 95 psi. This equipment was first used at Mather mine B shaft to concrete slusher drifts, Figs. 2 and 3, and finger raises located about 2000 ft from the shaft. In several instances there were bends into crosscuts and up vertical distances into the forms. For the first pours two placers were used. The first was located near the shaft where the concrete could be spouted into it from a 2-cu yd concrete bucket on the cage. The second was set on the side of the drift at a point approximately 1500 ft from the shaft. The concrete was shot directly into the second placer from the first unit and from the second machine directly into the forms. After completion of several pours with the two machines, a trial pour with only one placer located at the shaft proved that the second placer could be eliminated. Since then all pours have been successfully completed with only one placer underground. As production of iron ore from the mine increased and the development program expanded, use of the cage for handling mine supplies and concrete became a major problem. This brought about the first attempt at shooting concrete vertically down the shaft for 2600 ft. A 6-in. pipeline with victaulic couplings installed during shaft sinking was used for the trial. One placer was set on surface 250 ft from the collar of the shaft so concrete could be spouted directly into it from the mixer. This machine shot the concrete 250 ft horizontally on surface to the shaft, 2600 ft vertically down the shaft, and 100 ft horizontally into the second placer located near the rib of the shaft station or plat. The second machine shot the batch into the forms, about 2000 ft. Total distance horizontally and vertically was 4800 ft. The entire time cycle for a ¾-cu yd batch of concrete from the mixer on surface to the forms underground totaled about 5 min. During the past two years the two-placer method from the mixer on surface to the forms underground has proved a very efficient means of transporting underground concrete. Advantages of using pipeline concrete are as follows: 1—Interference with normal mining operation is eliminated. When the cage, skips, mine cars, or mine openings are used for transporting concrete and materials used for making concrete, mine operation suffers in one way or another.

Jan 1, 1955

By Charles Seastone

Location THE hydro-electric plant of the Peninsular Power Co., is located at what is commonly known as Lower Twin Falls on the Menominee River. This location is about 33 miles north of the city of Iron Mountain, Mich. The principal points of delivery of electric energy from this plant are in the mining regions adjacent to Florence, Wis., and Iron River, Mich., and in the cities of Iron River and Iron Mountain. The hydro-electric plant at Twin Falls and the substation of the Iron Mountain Electric Light & Power Co. are connected by a 6,600-volt transmission line carried on steel towers and steel poles, the latter being used within the city limits. The plant at Twin Falls and the substation at Iron River, about 36 miles distant, are connected by a 66,000-volt, duplicate, three-phase transmission line, supported on steel towers. At Iron River, are located a 1,500-kw. auxiliary steam plant, and the substation, from which the current is distributed to the mines in this vicinity. A description of the auxiliary plant, main and customers' substations, and of the main and secondary transmission lines, follows later in this paper.

Jan 2, 1915

By M. V. Nevitt

THE Cr,O-type, or P-tungsten, structure having the space group (Oh2— Pm,n) is one of the most widely occurring structures found among the intermediate phases involving transition metals. Including the phases reported here for the first time, the total number of these A,B phases now known is 39. Greenfield and Beck' have correlated the lattice parameters of these phases with the Goldschmidt radius of the close-packed chains of A atoms. Laves' discussed the apparent size of the A and B atoms in this structure. Gel1er" proposed a scheme for reproducing the lattice constants of the phases by the use of a list of effective C.N. 12 radii for the component elements. Reported here is a survey of the A,B combinations which appeared favorable for the stability of the Cr,O-type phase but which, at the time the investigation was begun, either had not been reported upon or had conflicting reports as to the existence of the structure. Seventy systems were investigated, and 8 Cr,,O-type structures were found. Six of these also were reported by other investigators in the interval between the start of this investigation and its completion. This survey yielded information as to the influence of the relative sizes of the A and B atoms on the stability of the phase and, for the various families of Cr,O-type phases, the effects of the sizes of the A and B atoms on the lattice constant. Likewise, a somewhat clearer picture of the connection between the position of the A and B elements in the Periodic Table and their Cr,O-type phase-forming tendencies has become apparent. Experimental Procedure Alloys were prepared in the form of arc-melted 3-gram buttons in all cases where the vapor pressure of neither component was high enough to cause

Jan 1, 1959

By G. K. Manning, C. H. Lorig

Two metallurgical tools have acquired wide use within the past several years as a means of studying the transformation characteristics of steel. One is a technique used first by Bain and Davenport for determining the transformation characteristics of a steel at constant temperature; the second is the end-quench hardenability test. Constant-temperature transformation curves like those of Bain and Davenport have done much to rationalize the metal¬lography of steel; however, in commercial practices, constant-temperature transformation is seldom encountered, therefore only rarely can such curves be directly applied. The real reason for the determination of such curves lies, in the fact that they provide a way of thinking about transformation that is both convenient and productive. The end-quench hardenability test is a more practical means of studying transformation, for, by correlating positions on the hardenability bar with shapes of different masses, an almost direct application of the results can be made. Unfortunately, the end-quench test, though practical, can do very little toward improving the metallurgists' way of thinking about transformation. These two metallurgical tools, dealing with precisely the same phenomenon, should be very closely associated in metallurgists' minds. Actually, they are frequently pushed into separate mental corners and considered as being more or less distinct and unrelated. The reason for this is that no strong connecting link between them has been developed. An attempt is sometimes made to relate these two tools by projecting the critical cooling rate on the isothermal transformation plot as illustrated in Fig. I. The critical cooling rate is considered as a constant rate-though in practical applications, cooling rates are never constant-and this constant cooling rate is given uniform significance from the Ae temperature down to the temperature of initial transformation. A little thought indicates the errors of such a procedure. Certainly the time interval spent just below point A of Fig. I cannot be as effective in promoting nucleation as is the time interval spent just above point B. Yet the procedure represented in Fig. I considers all the time spent between temperatures A and B to be just as effective in promoting nucleation as though all the time were spent at temperature B. Furthermore, change the shape of the isothermal curve between points B and C in any way desired, and the required critical cooling rate is not changed one iota. This cannot possibly be true. Such a way of thinking about critical cooling rates not only is incapable of giving any results that are quantitatively satisfactory but is likely to give very misleading qualitative results.

Jan 1, 1946

By H. E. McCoy, C. J. McHargue

Single crystals of columbium containing various levels of oxygen, nitrogen, carbon, or hydrogen were deformed by slaw compression and impact loading at -196°C. For the slow deformation rates. 1500 to 1900ppm oxygen, 500 pprn nitrogen, or 150 to 200 ppm carbon completely suppressed mechanical twinning. Hydrogen in concentrations to 1000 ppm had no apparent effect on ease of twinning. Impact loading caused twins to form at all levels of contamination studied, and cleavage mucking on (100) planes occurred in specimens having higher interstitial contents. It is well established that, under some conditions, the bcc metals vanadium, columbium, tantalum, chromium, molybdenum, tungsten, and iron deform by formation of mechanical twins. In general it has been accepted that high strain rates, low temperatures, and large grain sizes are conducive to this kind of deformation.' Since interstitial impurity atoms have a relatively large effect on slip in bcc metals, one might sus- pect a similar effect on twinning. This could occur directly by the interstitials affecting the nucleation or growth of the twins or indirectly from their effect on slip. It has often been argued that the large increase in yield stress caused by interstitial elements enables the effective stress to exceed that necessary to cause twinning. The twinning stress has always been thought to be higher than the stress necessary to cause slip in pure metals.2 simonsens and Tipper and Hall4 found profuse twinning in very pure a iron even at room temperature, whereas Low and Fueste15 and Churchman and tottrell' observed twins in a iron containing carbon but none in highly decarburized specimens. McHargue7 reported mechanical twins to form readily in vanadium which contained 390 ppm interstitigs, while Clough and Pavlovic8 found twins only in the one or two grains adjacent to the fracture surface in vanadium which contained 1500 to 1700 ppm interstitials. In columbium, McHargue9 found high-purity single crystals to twin easily whereas Churchman,10 Adams, Roberts, and mallman,11 and Johnson12 studied less pure material and found far fewer twins. Although the results of Leadbetter and Argent13 showed oxygen to inhibit twinning, a study by sheely14 indicated the opposite to be true. Chromium exhibits this mode of deformation15,16 but there are no data regarding impurity effects. Lawley, Van den Sype, and Maddin17 observed twins in very pure molybdenum single crystals deformed at 77°K but none in less pure crystals. The work by Cahn18 and

Jan 1, 1963

By N. M. Langdon

Spokane Meeting, September, 1909.) THE following corrections to the paper of Mr. Langdon (Bulletin No. 34, October, 1909, pp. 919 to 940), received after the publication of the paper in the Bulletin, will be incorporated in the paper as finally published in the forthcoming Vol. XL. of the Transactions, but are here presented for the information of members:' Page. 921. Table I., furnace M2, item 11. For " 8801 " read "0.8801." 922. Table II., furnace C, item 2, under gas. For " 0.011 C " read " 0.011 0." Furnace G, item 13, under gas. For " 5.074 air " read " 3.074 air." Item 15, 114.269 " should be " 4.289." Furnace H, item 2, under iron. For " 0.04 " read ".0.01." 923. Table II., furnace J, item 1, under iron. For " 0.95 " read " 0.93." Furnace N2, item 6, under gas. For " 0.66 CO," read 0.066 C02." 924. Table III., furnace C, item 17. For " 379 " read " 397." 927. Table IV., furnace C, item 4. For " 0.0124 " read 0.0424." Furnace G, item 15.. For " 4,060 " read " 4,066." 928. Line 2. Items 19 and 20 of heat-supply, should be items 20 and 21. 930. Line 3. Expunge remainder of paragraph after the word " supplied," and substitute the following : "As compared with the fusion-zone, the loss by radiation n C was 25.5 per cent. of the total (2,278 units) supplied to that zone, while in D it was 22.5 per cent. of the total heat (1,824 units) supplied to that zone. Finally, as compared with the reduction-zone, C lost by radiation 36.8. per cent. of the 1,580 units supplied to that zone,

May 1, 1910

By Kirtland Marsh

THE manufacture of gas masks by the Chemical Warfare Service, U. S. A., required preparation of the carbon used in the canisters. The largest plant for the production of this carbon was situated at the works of the Astoria Light, Heat and Power Co., at Astoria, N. Y.; this paper will deal1 with the pyrometry equipment at that plant. Commercial charcoal was found unsuitable for use in gas masks because of its low power of absorption and its poor resistance to abrasion. The best raw material for the production of carbon was found to be coconut shells, but any kind of nut shells or fruit pits were used when sufficient quantities of coconut shells could not be obtained. The shells were first carbonized in retorts, the carbon was then crushed and screened between 8 and 16 mesh, and finally submitted to a special heat-treatment in air; steam treatment was later substituted for treatment in air. The production of gas-mask carbon on a commercial scale was begun at Astoria about Aug. 1, 1917. Temperature control was essential during the initial carbonization of the shells, as well as during the air or steam treatment, and pyrometers were installed for this purpose. The installation and maintenance of all pyrometry equipment was done by the pyrometry department, consisting of an officer in charge, an assistant, and two men. A special pyrometry laboratory was maintained in which all repairs were made.

Jan 9, 1919

By AIME AIME

HE State of Utah has an area of 84,990 sq. mi., and like other inland states in the West its population, although steadily increasing, is relatively small. The fact that it is a state possessing vast mineral resources is attested by a careful study of statistics which have been compiled by Federal and State investigators. Some idea of the extent of these resources and the degree of development of a particular state or region may be gained by such a study, but in the case of Utah statistics and other available information fail to portray completely the true extent and value of its existing metallic and non-metallic resources. The State is probably more widely known for its production of metallic ores which has placed it in an eminent position among the metal mining states of the Nation.

Jan 1, 1925

By J. M. Callow

THE results obtained by pneumatic flotation throughout the country on all classes of ore, and. the tonnage now being treated by this particular method, speak for themselves. Its advantages over the so-called agitation process are now established by facts and data from practice. The comparative efficiency of a rapidly revolving paddle, as a means for aerating an ore pulp, and of a cycloidal or turbine blower for the same purpose, would seem to be so obvious as to leave no room for discussion. Practitioners in this art are to be congratulated on the acquisition of the valuable literary contributions that have recently been made on the theory of. flotation by Messrs. Ralston, Van Arsdale, Taggart and Beach, and others, and the very valuable and able articles, by Messrs. Laist and Wiggin on "Flotation Concentration at Anaconda, Mont.," by, Dr. Rudolf Gahl- on the "History of Flotation at Inspiration," and by David Cole on "The Advent of Flotation in the Morenci District." It is not within the province of this article to attempt an answer to the various issues raised in regard to the theory, or to defend the one advanced by me a year ago. But since discussion usually benefits the profession, a reply will be made to some of the statements made by the last-named writers. COMPARATIVE SENSITIVENESS AND ATTENDANCE Concerning 'the article, "Flotation Concentration at Anaconda, Mont.," by Laist and Wiggin, a little explanation is in order. It should be stated that; with the exception of about 24 days at the end of the testing 'period, the Callow experimental plant at Anaconda was not run under my direction. This perhaps accounts for some of the conclusions drawn on page 562 of the descriptive paper. The conclusion that the use of acid seems to be of considerable advantage, calls, for some comment. While the tests conducted by the Anaconda Copper Co. do show acid to be, of considerable benefit, this is a consequence of using acid sludge as a flotation agent. My belief has always been that the Anaconda

Jan 2, 1917

By J. E. Hanlon, S. R. Butler, R. J. Wasilewski

It is known that stoichiometric NiTi transforms to a structure of lower symmetry near room temperature. The present investigation deals primarily with the changes in the electrical and magnetic properties which occur at the transformation. The effects of composition and various heat treatments on electrical properties are also discussed. In recent investigations by Purdy and Parr,' Wang et a1.,2 Dautovich and Purdy,~ Dautovich et a1.,4 and the authors, ~,' NiTi has been observed to undergo a martensitic phase transformation from the ordered CsCl (B2) structure to one of lower symmetry. The crystal structure of the low-temperature modification is still not completely worked out. This transformation occurs near room temperature for the stoichiometric composition. The thermodynamic, elastic, crystallographic, and microstructural characteristics of this transformation for some compositions have been previously reported.'-= In the present investigation, the changes in the electrical transport properties and magnetic susceptibility of NiTi when it undergoes the martensitic phase transformation have been measured. The approximate composition range covered is 48 to 52 pct Ti.* *All compositions are given in atomic percent._____________________ EXPERIMENTAL PROCEDURES AND RESULTS 1) Sample Preparation. The NiTi alloys were prepared from iodide titanium (>99.92 pct Ti) and vacuum-premelted carbonyl nickel (>99.95 pct Ni) by repeated arc melting under gettered argon and casting in a water-cooled copper mold. After the cast buttons were hot-forged at 800" to 950°C, the oxidized surface was removed by grinding and etching. Samples were cut from the worked polycrystalline buttons. After fabrication, the samples were annealed 1 hr at 900°C and water-quenched. The composition of the alloys was assumed to be the same as in the initial feed. This assumption was supported by material balance checks on 100-g arc-melted buttons which demonstrated quantitative recovery to within k0.02 pct. The oxygen content of the alloys was '150 ppma (weight) and the carbon content was 30 to 50 ppm. 2) Electrical Resistivity and Hall Effect. The electrical resistivity was measured over the composition range 48 to 52 pct Ti for temperatures varying from 4.2"K to 900°C. The high-temperature and many of the low-temperature experiments were carried out using conventional 4-probe dc techniques.7 The Hall coefficient and ac resistivity were measured at 20 cps using the apparatus shown schematically in Fig. 1. The equipment is basically an ac potentiometer: The resistive or Hall voltage of the sample is balanced by a comparison voltage provided by a dividing network across a standard series resistance. The off-balance signal is amplified by a Tektronix 122 amplifier and detected by a Princeton Applied Research (PAR) phase-sensitive detector. The precision of the resistivity and Hall coefficient measurements is i0.1 and i3 pct, respectively. The uncertainty in the data is increased by i2 pct from the precision limits because of uncertainty in dimensions and possible end effects. The temperature dependence of the electrical resistivity and Hall effect for a stoichiometric (50.0 pct Ti) NiTi sample are illustrated in Fig. 2. Above 75"C, this sample has essentially the B2 structure, while below about 0°C it is completely in the low-tempera-

Jan 1, 1968

By R. Simon

Maurer's review1 summarizes quite thoroughly the various theoretical developments and experimental findings that contribute to the knowledge of rock mechanics in drilling. This discussion supplements Maurer's paper by including generalities that either have been incompletely treated in his review, or formulated from new considerations by the discussant and from hitherto unpublished experimental data. These generalities are associated with the observation that all mechanical methods of rock drilling essentially comprise a sequence of indexed, concentrated loadings on the bottom of the hole being drilled. A concentrated loading is defined as a mechanical loading by a tool that contacts at any one time only a small fraction of the surface of the body being worked and penetrates only a small fraction of the body thickness. The surface in this application is the bottom of the hole. The deformation of ductile material by concentrated loading has received considerable attention because of the importance of indentation tests for measuring hardness of metals. Some of the generalities involved in concentrated loadings on ductile materials apply also to concentrated loadings on more brittle materials such as rock. Among these generalities is the applicability of similitude considerations to scaling laws and to force-displacement and energy-volume characteristics for tools of various shapes, as summarized by Tabor.2 Vork on the flow and fracture behaviors of glass loaded with pyramidal and spherical indenters is reviewed by Douglas.3 Maurer refers to the work of Evans and Murrell on wedge loadings on coal and on mixtures of pitch and sand. It is evident from Maurer's paper that a considerable portion of the studies of rock mechanics in drilling, such as crater formation experiments, has involved concentrated loadings on rock.

Jan 1, 1967

By N. C. Fick, R. L. Rickett

DESPITE the large volume of literature on alloys of iron and silicon,1 there is little published information dealing specifically with the constitution, at various temperatures, of the alloys containing less than 0.10 per cent carbon and from 0.5 to 4.5 per cent silicon that are used extensively in the electrical industry. Because such information was needed by those engaged in the production of these alloys in, sheet and strip form, the constitution was determined of a series of commercial silicon steels containing 0.05 to o.08 per cent carbon and 0.20 to 4.31 per cent silicon, over the temperature range 1300° to 2500°F. These alloys were all from regular production heats and of commercial quality. The results of, the tests are given in Fig. I and for comparison the constitution diagram of iron-silicon alloys with 0.01 to 0.02 per cent carbon, taken from the literature, is also presented. MATERIAL AND PROCEDURE All steels were hot-rolled to a thickness of 0.060 to 0.080 in. and used in this condition. Their chemical compositions, including over-all check analysis, and "center" analysis for carbon and silicon, are given in Table I. The so-called center analysis was determined on samples pickled to remove the outer surface and leave only the center third of the gauge thickness-the portion of the sample on which metallographic ratings were based. In most, but not all, of the alloys, slightly higher carbon was found at the center than when the whole strip was sampled; the two methods of sampling show relatively little difference in silicon. Two of the steels, A and E, contain relatively high phosphorus, while I and K are somewhat higher in manganese than the others. [ ] The procedure consisted essentially of heating specimens (about 1/16 by 3/8 by 3/4 in.), protected from oxidation or change in carbon content, at a temperature in the desired. range and for a selected period, after which they were quenched in iced brine; the degree of transformation that had then occurred was determined by metallographic examination. The soaking periods were selected after preliminary investigation had shown that a con-

Jan 1, 1946

The ten-year "supply-demand relationship" tables in this chapter for various mineral and metal commodities have been adapted from Minerals in the U.S. Economy, compiled by the Bureau of Mines, U.S. Department of the Interior, published in 1975. Acknowledgment is made to the Bureau of Mines for compilation of the tables. [ ]

Jan 1, 1976

By Sherwin F. Kelly

THIS is intended as a simple review of the principles and practice of geophysics, so will not be of interest to the geophysicist, who is hereby warned of its elementary character. The engineers for whom it is written are those who, having glimpsed the formidable formulas and discussions of the geophysicists, give all publications on the subject a wide berth. For a few years now the geo-physicists have had a tendency to be ingrowing at their meetings, going deeper and deeper into theory and instrument construction, and forgetting to present the topics that would interest the practicing engineer who desires merely to know how geophysics can help him, not why.

Jan 1, 1934

By R. G. Treuting

Germanium single crystals strained in tension at 600°C slip on the {Ill} plane and, macroscopically at least, in the <110> direction. Deformation is in homogeneous: various localized rotations are observed, as is a banding consistent with secondary slip banding. The structure after deformation is polygonized with a domain size of about 2x1O-3 cm. In relaxation tests, an incubation period prior to flow is observed, of duration inversely related to temperature and applied stress. Under continuous loading, there is a sharp first yield point. A critical resolved shear stress therefore must be cited with respect both to temperature and to rate of loading. At 600°C, when loading proceeds at 2900 psi per min, it is 1310 psi. The yield point phenomenon is suggestive of Cottrell&apos;s solute atom atmosphere theory and five points of qualitative agreement with this theory are found. PLASTICITY of germanium at elevated temperatures has been reported by Gallagher,&apos; who ascribed it to slip on {Ill) planes and described some associated effects. Preliminary experiments with single crystals of silicon and germanium loaded as simple beams confirmed {ill) as the slip plane of both materials.V his was demonstrated by the standard technique employing traces on two surfaces of known angle on a deformed crystal of known orientation.3 These experiments did not fix the slip direction, since more than one glide system operated. Uniaxial tensile straining is preferred for this purpose in order to restrict slip to one predominant system and to provide an unequivocal determination of the orientation change with respect to the stress axis. Experimental Method Specimens were diamond-sawed from germanium crystals containing about 5x10-5 wt pct Sb prepared by the zone-leveling process described by Pfann and Olsen;4 these specimens measured about 81/2 in. long, 0.20 in. wide, and were of various thicknesses from 0.035 to 0.060 in. Prior to testing, a specimen was coated over 1 in. or more of length at each end with Apiezon wax, chemically polished (in a solution of 15 ml HF, 25 ml HNO,, 15 ml CH3COOH, and 3 to 4 drops Br2), and dewaxed in warm xylene. A brief re-etching after scribing through a complete wax coating with vernier dividers provided gage marks at 0.200 in. intervals on the polished surface. A specimen with grips soft soldered to the ends was passed through the furnace tube and the grips pinned to the tensile machine in series with a stress gage. The Schopper testing machine is best described by reference to the illustration on p. 107 of Schmid and Boas5 and is operated with the pendulum arm locked, fixing the upper head. Load is applied through the screw-driven lower head, manually or by reduced speed motor. The furnace is 21/2 in. long surrounding a 4x7/16 in. ID quartz tube and was positioned about the specimen to permit free motion. The inert or reducing atmosphere required was sufficiently provided by a flow of helium introduced at the center of the furnace tube, with the tube ends loosely plugged with asbestos paper. Surface corrosion was slight. The stress gage employs a Be-Cu strip with SR-4 units incorporated in a simple bridge network with provision for balancing and calibrating. The bridge output on loading is fed through a Leeds and North-rup dc amplifier to a Speedomax 10 mv recorder, and calibration is obtained by dead loading. Experiments of two types have been conducted. Most have been in relaxation at constant elongation. One stress-strain curve has been taken with the machine continuously driven. Following extension of a specimen, Laue X-ray photographs were taken to obtain the orientation change between deformed and undeformed regions, recorded on a single film by translating the specimen in a plane normal to the beam between exposures. Sequences of such multiple exposures were made on some specimens to include the entire orientation range on one film. Slip Direction To obtain a maximum orientation change with a single slip system, crystals of very closely <110> axial orientation were used. The classic determination of slip direction rests on establishing that direc-

Jan 1, 1956

By Louis V. Bender

THIS paper gives a short review of the installation for and the use of gas, as a. fuel, at the Anaconda Reduction Works of the Anaconda Copper Mining Co. Before putting in gas tile fuels used were pulverized coal, lump coal, coke distillate and oil. These fuels are now almost entirely eliminated. For nearly fifty years bituminous coals from Wyoming and Montana fields had been used. These coals were of a good grade, analyzing 11,300 B.t.u. and having an ash content of 12 per cent. When hydro-electric power replaced steam-driven equipment, the coal requirements were reduced; and, on account of improvements in metallurgy and/ or in furnace design, the quantity was lessened. Later, oil and distillate were introduced and used in some of the operations. All of these things tended toward the lessening of the amount of coal used, and had it not been for the increase in the size of the plant, the tonnage used would have been small when the change was made to gas.

Jan 1, 1932