Search Documents

By Michael Perch, Charles C. Russell

Nearly 7 5 per cent of the total coke production in the United States in 1940 was consumed in blast furnaces. In 1939 the percentage was 69.9, and in 1938 it was 61.3. To produce a net ton of pig iron 1757 lb. of coke was required in 1940 and 1760 lb. in 1939. These figures indicate how dependent the production of pig iron is upon the production of coke. The rate of iron production is in some measure influenced by the physical and chemical characteristics of the coke. Blast-furnace operators believe that the physical properties of coke profoundly influence the operation of the furnace. Although it is true that coke of a wide variety of physical properties is used in American blast furnaces, the periodic fluctuation of these properties is one of the causes of irregularity of blast-furnace operation. The purpose of this paper is to present a broad picture of the physical properties of by-product coke that are generally considered to be important by coke-oven and blast-furnace operators. Effects of the kind of coal used, the preparation of the coal, the rate of coking, and other factors will be considered. Of all these variables, the kind of coal used is by far the most important. In this discussion use will be made of the method of coal classification by rank1 standardized by the American Society for Testing Materials. Although this method of classification has been an American standard for several years, it has not been given the attention it deserves, especially in connection with the selection of coal for production of coke. Despite the fact that many producers of blast-furnace coke are limited to some particular source or sources of coal, a good understanding of the principles involved in setting up the standard method of classification may lead to a better appreciation of the causes of changes in coke characteristics. Furthermore, where it is necessary to select new coals as a substitute for the original supply, this method of classification can be of great assistance. The data presented have been gathered from many sources, but no attempt has been made to cover the vast literature. Instead, some of the more important data have been selected to show how coals and their carbonization affect some of the physical properties of coke. It must be emphasized that generalizations concerning the behavior of coking coals are presented and that individual coals may vary widely from the specific behavior depicted. Nevertheless, it is believed that the data illustrate certain typical behaviors. Neither was it possible to cover completely all the factors involved; for example, the macroscopic constituents of coal are believed to have important effects on the physical properties of coke, but since there is little information available for such study, and since vitrain, clarain, and durain are neither

Jan 1, 1943

By Michael Perch, Charles C. Russell

Nearly 7 5 per cent of the total coke production in the United States in 1940 was consumed in blast furnaces. In 1939 the percentage was 69.9, and in 1938 it was 61.3. To produce a net ton of pig iron 1757 lb. of coke was required in 1940 and 1760 lb. in 1939. These figures indicate how dependent the production of pig iron is upon the production of coke. The rate of iron production is in some measure influenced by the physical and chemical characteristics of the coke. Blast-furnace operators believe that the physical properties of coke profoundly influence the operation of the furnace. Although it is true that coke of a wide variety of physical properties is used in American blast furnaces, the periodic fluctuation of these properties is one of the causes of irregularity of blast-furnace operation. The purpose of this paper is to present a broad picture of the physical properties of by-product coke that are generally considered to be important by coke-oven and blast-furnace operators. Effects of the kind of coal used, the preparation of the coal, the rate of coking, and other factors will be considered. Of all these variables, the kind of coal used is by far the most important. In this discussion use will be made of the method of coal classification by rank1 standardized by the American Society for Testing Materials. Although this method of classification has been an American standard for several years, it has not been given the attention it deserves, especially in connection with the selection of coal for production of coke. Despite the fact that many producers of blast-furnace coke are limited to some particular source or sources of coal, a good understanding of the principles involved in setting up the standard method of classification may lead to a better appreciation of the causes of changes in coke characteristics. Furthermore, where it is necessary to select new coals as a substitute for the original supply, this method of classification can be of great assistance. The data presented have been gathered from many sources, but no attempt has been made to cover the vast literature. Instead, some of the more important data have been selected to show how coals and their carbonization affect some of the physical properties of coke. It must be emphasized that generalizations concerning the behavior of coking coals are presented and that individual coals may vary widely from the specific behavior depicted. Nevertheless, it is believed that the data illustrate certain typical behaviors. Neither was it possible to cover completely all the factors involved; for example, the macroscopic constituents of coal are believed to have important effects on the physical properties of coke, but since there is little information available for such study, and since vitrain, clarain, and durain are neither

Jan 1, 1943

By M. T. Hepworth, A. K. Stewart

Iron containing 0.1 pct A1 and -0.9 pct P by weight was internally oxidized in the temperature range 900° to 1300° C, where the bcc structure is stabilized by phosphorous. By measuring the depth of penetration of oxygen with time in an internally oxidized zone for an imposed surface oxygen potential, oxygen permeability was determined. The dgfusion coefficient of oxygen in iron was then calculated using known solubility data, yielding the expression: where Do is the diffusion coefficient of oxygen in bcc iron in sq cm per sec and T is temperature in OK. RECENTLY Hepworth, Smith, and Turkdoganl measured the diffusivity of oxygen in bcc iron and reported the temperature dependence of diffusivity from data determined in the a, and 6 temperature ranges. Subsequently Swisher and Turkdogan' have measured the diffusivity of oxygen in fcc iron. Internal oxidation techniques were employed by these investigators and in this current study. The analysis of this technique is developed by wagner3 (presented in English by Hauffe4 and Rapp 5). In this present study bcc iron stabilized by phosphorous was used to determine oxygen diffusivity in the temperature range 900° to 1300°C. Meijerin 6 has studied oxygen permeability in this temperature range using bcc iron stabilized with 5 pct Sn. Other inves- tigators who have studied oxygen permeability in bcc iron at other temperatures are Schenck et al., 7 Bohen-kamp and Engell, 8 and Bradford. EXPERIMENTAL Electrolytic iron of 99.99 pct purity was alloyed to contain 0.897 pct P and 0.093 pct Al. The maximum weight percent phosphorous required to stabilize bcc iron between 910" and 1392°C is 0.51 pct as determined by Haughton,10 0.42 pct by Roquet and jegaden," and 0.58 pct by vogel,12 with the latter value preferred by Hansen.13 Microprobe analysis indicated that there was no segregation of the phosphorous either before or after permeability studies; therefore, the quantity of phosphorous added was assumed to be sufficient to stabilize the bcc structure. Furthermore, the permeability results of studies on this alloy agreed substantially with interpolated values from previous data on bcc iron.' An ingot of the Fe-P-A1 alloy was hot-rolled to a l-in.-thick slab. Specimens were machined to dimensions: 13/8 by $ by 1/4 in. The experimental apparatus and procedure used have been described before.' A constant oxygen potential was established by passing argon and hydrogen through a column of oxalic acid dihydrate, which has a water vapor pressure which is well-known as a function of temperature. Slab specimens were exposed to a gas mixture sufficiently lean in oxygen to prevent the formation of a surface oxide for predetermined temperature for selected times. The specimens were then quenched, sectioned, and examined metallo-graphically. All quenched specimens were iron-plated to provide protection from the outside sample edge during polishing. Fig. 1 shows a typical microstruc-ture for a specimen oxidized at 953°C for 48.00 hr at a water vapor-to-hydrogen pressure ratio of 0.20. DISCUSSION AND RESULTS The following equation was derived by Hepworth et al.' from Wagner's kinetic expressions for internal oxidation:

Jan 1, 1969

By David L. Riley

Organization The Foundling Years - 1901-1921 Two events that occurred in the decade of the 1870's have had far- reaching effects upon the petroleum industry in the U. S. and formed a basis for the birth and growth of the petroleum engineering profession. In 187 1 a group of mining engineers banded together to form the American Institute of Mining Engineers "to promote the arts and sciences connected with the economic production of the useful minerals and metals and the welfare of those employed in these industries by all lawful means". Although it was to be 30 years before an event in Jefferson County, Tex., would cause petroleum to come into prominence as the world's principal source of energy, the founding of AIME provided an organization through which the application of engineering to the recovery of petroleum and natural gas could be developed. In 1875, a Pennsylvania judge who was called upon to make a decision for which there was no precedent reasoned that oil and gas were like wild game - they belong to the man who can reduce them to possession. His decision sired the "rule of capture", which stated that a landowner possesses the oil produced from his well, even though it might have come from beneath his neighbor's land. This interpretation prevailed for more than half a century, during which time gold-rush tactics were employed in the drilling and production of many oil fields in the U. S. The resulting overproduction and tremendous waste led to a virtual economic collapse of the U. S. petroleum industry by the early 1930's. To bring these malpractices under orderly control, proration and conservation policies were developed, and petroleum engineering became the medium through which they were devised and implemented. At the turn of the 20th Century, more than 90 percent of this country's oil production came from the East, but the picture changed with dramatic suddenness on Jan. 10, 1901. Captain Anthony F. Lucas, an Austrian mining engineer, had noticed concentrations of oil and gas near salt domes during mining operations on the Louisiana Gulf Coast. In 1899 he leased a low mound near Beaumont, Tex., began drilling, and after almost 2 years of intermittent operations, brought in the famous "Lucas Gusher"

Jan 1, 1971

By Larry Kaufman, Joan B. Berkowitz-Mattuck, Edward V. Claugherty

The oxidation characteristics of hafnium and zirconiunr diboride were measured between 1200 and 2200'K by a thermal- conductivity method which continuously ttzeasures the rate of reaction of oxygen with the diboride and by a metallographic air oridation method zuhich provides a measure of the total arr7ount of bovide conuerted to oxide for a given time interval. The oxidized specimens obtained from the tl~eritaal-coi~ductitrity method were also examined by quantitatire metal-lographic procedares. The significant results obtained in this investigation reveal that metal-rich compositions of lzafi~iutil diboride proride the most oxidation-resistatzt material up to 2000°K; hafnium diboride is tmre oxidation- resistant titan zirconium diboride at all tempevatures examined; the morphology of the oxide formed on H/B2 and Llie temperature coefficient qi. the oxidation rate constants change at the temperature of ttze monoclinic to tetragonal phase transition] in HfO2; the oxidation of neither HfB2 nor ZrB2, results iN catastrophic Jazlure at lorc. oxygen pressures; and pvefevetztial gvaLti boundary oxidation was not obsevued for either HfBi or ZYB, A comprehensive study of the high-temperature characteristics of refractory transition-metal di-borides is currently in progress. This program has included investigation of the physical, thermal, and thermodynamic properties of TiB2, ZrB2, HfB2, NbB2, and TaB2. In addition, aspects of the synthesis and fabrication of such materials have been studied. In view of the diverse nature of this research, a number of other laboratories have actively participated and contributed specific capabilities for analysis and characterization of these materials. As a consequence, an extensive description of the relevant properties of these compounds has emerged which is central in evaluating their high-temperature (1200" to 2500°K) performance. To date, information on thermodynamic stability, specific heat, and vaporization characteristics,1 hot hardness and electrical resistivity,1, 3 therma1 expansion:'4 and thermal conductivity 1, 5 has been presented. This information has been generated on materials of the highest purity (98.5 to 99.9 wt pct Me + B) and density currently available. Samples fabricated by zone melting6 and high-pressure hot pressing"3'7 techniques have been used to generate suitable specimens for all of the aforementioned studies. dation characteristics of the most oxidation-resistant of these materials, hafnium and zirconium diboride, is presented and a description of the synthesis and the experimental procedures used to prepare and characterize specimens is given. The high-temperature range under consideration (1200" to 2200°K) and the known dependence of oxidation characteristics on sample chemistry, density, and oxidation conditions required a close coupling of the synthesis, fabrication, and evaluation procedures.8 This was accomplished by continual surveillance of chemical composition of starting materials before and after specimen fabrication and by evaluation of density, phase constitution, and microstructural features prior to and after oxidation exposure. I) PROCUREMENT AND CHARACTERIZATION OF STARTING MATERIALS In view of the current state of the art in fabricating refractory boride materials, the methods used in preparing samples for the present study are given in detail as follows: starting materials were purchased in high-purity powder form and fabricated by high-pressure hot pressing into 0.40 by 1.00 in. bars from which oxidation specimens were obtained. The hafnium diboride used in this study was purchased from Wah Chang Corp.; the zirconium diboride from U.S. Borax and Chemical Co. These powders were routinely characterized by quantitative chemical analyses for metal, boron, carbon, oxygen, nitrogen, and iron, by qualitative emission-spectrographic analysis for trace impurities, by X-ray procedures for extraneous phase identification, and by powder densitometry for comparison with X-ray (theoretical) density. Hafnium and zirconium metal and elemental boron were also purchased as high-purity powders and characterized for impurities by emission-spectrographic analyses. The hafnium diboride was procured in three shipments which were designated as HfBl.g7(1), HfB1.88(2A), and HfB2.12(2). The indicated stoichiometry is based on the atomic ratio of total boron to total hafnium; the number in parentheses identifies the shipment number. Shipment 1 was 5 1b, shipment 2A, 1 1b, and shipment 2, 8 1b. The zirconium diboride was procured as a 20-1b shipment and designated as ZrB1.89(1). A small quantity of purified zirconium diboride was also supplied and designated ZrB1, 9(P). The averaged results for chemical analyses which were generally performed according to the procedures set forth in the compilation by KrieGe9 are presented in Table I. Qualitative spectrographic analyses indicated that Ca, Cr, Ti, Si, Zr (in H~B~), and A1 were present at levels between 0.01 and 0.10 wt pct. Other metallic elements were found to be less than 0.01 wt pct. Since it is virtually impossible to purchase these materials in the desired quantities (5 to 20 lb) as single-phase compounds it is necessary to obtain

Jan 1, 1968

By E. V. Crane

A tremendous volume of the metal rolled annually into sheets strips and coil stock finds its way to a host of stamping and manufacturing plants which are the quantity production units of the country. Considerable in volume, too, are the rolled and extruded rods which go into forging and manufacturing plants for conversion into the same general line: those widely sold metallic necessities and luxuries of the household, the office, transportation, farming and building construction. Yet, in spite of its age and its importance, the stamping trade has been doing its "engineering" largely by trial and error. Its distinctive method is shearing out and plastically working metal to finished shape in a few quick strokes with high loads and expensive tools which are warranted only by large quantities to be produced. The principal operations have many features In common with rolling and wire-drawing methods. Combinations of stresses are diffcrent, however, and details of operations are infinite in variety. An engineering study of the subject begins with stress analysis, but must go back to metallurgy for its foundation. A grouping of pressed-metal working operations according to whether the metal is (1) sheared, (2) bent, (3) drawn or (4) squeezed has proved useful. All of these groups include instances of both hot and cold operations. For discussions of metal working properties, the division between hot and cold working is taken as the recrystallization range of temperature. This, of course, brings tin, lead and often zinc into the hot-work range at or near room temperature. The outstanding hot-working press field is in forging: particularly of brass; all of which is included in the squeezing group. Shearing Operations The shearing group of operations, including blanking, piercing, trimming, shaving, slitting, shearing, notching, parting and numerous variations and combinations of these enters once or more into the production schedule of practically every stamped or forged article. The transverse stress, set up in shearing, as shown in Fig. 1A, is a combination of an angular compressive thrust and a tensile stress which is also at an

Jan 1, 1931

By A. F. Crawley

THIS communication reports measurements of the densities of dilute liquid alloys of 0.1 and 0.5 pct Ag in Sn over temperature ranges of 170" and 210°C, respectively, above the melting point of pure tin (232°C). The work was earried out to provide accurate density data for some liquid diffusion studies performed by Davis.1 Densities were measured using a pycnometric technique established in this laboratory. Earlier papers2, 4 attest to the accuracy of ±0.05 pct and the reliability of the method. Tin, 99.999 pct pure, and silver 99.99 pct pure, were melted in a graphite crucible in a vacuum furnace and held at temperature for 10 hr to ensure homogenization. Ingots suitable for machining

Jan 1, 1970

By J. P. Lesley

The Pittsburgh coal-region, if we regard the greatness of its extent, the picturesque beauty of its scenery, the salubrity of its climate, its relative situation on the Continent, the fertility of its soil, its unrivalled mineral wealth, and its magnificent system of natural transportation, is, perhaps, the most valuable spot on the surface of the planet. Unlike the mythical Paradise inhabited by one man and one woman, it swarms with an abounding population, not living on the free gifts of nature without care and without toil, hut expending its energies in unremitting labor, reinforced by the most elaborate machinery, in the production of everything which mankinds needs or desires; and unlilte the Paradise of story from which flowed the four great rivers of the world in opposite directions, its own four rivers How from the surrounding world into it, to constitute by their union the great highway water-course which divides the Northern from the Southern States. These rivers are the Monongahela, coming from the south, the Yonghiogheny from the southeast, the Kiskiminetas from the east, and the Allegheny from the north. Uniting at the great city of pittsburgh, they constitnte the Ohio, which flows northwest and west, and then south and southwest, toward the Mississippi. The Monongahela has been made navigable by a system of dams and pools the Allegheny was navigable in its natural condition; the KisKiminetas was made navigable by a State canal which has been vacated ; and the Youghiogheny remains unnavigable. Railroads supplement the deficiencies of the rivers, follow their hanks, and share in the transportation for which the waters are not sufficient. Railroads and rivers concentrate at Pittsburgh; other railroads cross the highlands to the east and west; and branch roads ascend the side-valleys and ravines to the mines on the uplands. The whole region is a scene of life; towns and villages dot its surface in all directions ; hundreds of gangways open upon the sides of all the valleys, and deliver coal to trains of cars which move beneath them at water-level; furnaces and rolling-mills abound; hundreds of oil-wells furnish a flood of liquid fuel to pipe-lines

Jan 1, 1886

By Shiou-Chuan Sun

THIS paper presents the design and operation of a frothmeter capable of measuring the frothing characteristics of pine oils and other frothing reagents. The experimental data show that the frothability of pine oil is governed by: 1-rate of aeration, 2-time of aeration, 3-height of liquid column, 4-chemical composition of pine oil, 5-pH value of solution, 6-temperature of, solution, and 7-concentration of pine oil in solution. The effect of mineral particles on the behavior of froth also was studied, and the results can be found in a separate paper.1 The results also show that the relative frothabilities of pine oils in the frothmeter generally correlate with those in actual flotation, provided that other factors are kept constant. In addition to pine oils, the other well-established flotation frothers were tested, and the results are included. In this paper, compressed air frothing is the frothing process performed by means of purified compressed air, whereas sucked air frothing is the frothing process accomplished by purified air sucked into the glass cylinder by a vacuum system. The term vacuum frothing denotes that froth was formed by degassing of the air-saturated liquid under a closed vacuum system. Apparatus The frothmeter, shown in Fig. 1, is capable of reproducibly measuring the volume and persistence of froth as well as the volume of air bubbles entrapped in the liquid and is capable of being used for compressed air frothing, sucked air frothing, and vacuum frothing. Fig. la shows that for compressed air frothing, the apparatus consists of an airflow regulating system, 1-3; a purifying and drying system, 4-8; a standardized flowmeter to measure the rate of airflow from zero to 500 cc per sec, 9; and a graduated glass cylinder, 13; equipped with an air regulating stopcock, 10; an air chamber, 11; and a fritted glass disk to produce froth, 12. The fritted glass disk, 5 cm in diam and 0.3 cm thick, has an average pore diameter of 85 to 145 microns. The pyrex glass cylinder has a uniform ID of 5.588 cm and an effective height of 63 cm. The inside cross-sectional area of the glass cylinder was calculated to be 24.53 sq cm, or 3.8 sq in. For sucked air frothing, Fig. lb shows that the apparatus for compressed air frothing is used again, with the following modifications: 1-compressed air and its regulating system, 1-3, are eliminated; and 2-a vacuum system, 16, equipped with a vapor trap, 15, and a vacuum manometer, 17, is added. The vacuum system can be .either a water aspirator or a laboratory vacuum pump. Any desired rate of airflow can be drawn into the glass cylinder, 13, by adjusting the opening of the air regulating stopcock, 10. The sucked air stream is cleaned by the purifing and drying system, 4-8, before entering the glass cylinder, 13. When this setup is used for vacuum frothing, the air regulating stopcock is closed. The frothmeter has been used for almost 3 years and has proved to give reproducible results, as illustrated in Table I. With a magnifying glass and suitable illumination, the frothmeter also can be used to study the attachment of air bubbles to coarse mineral particles.2 Experimental Procedures Except where otherwise stated, the data presented were established by means of the compressed air method. The volume and persistence of froth were recorded respectively at the end of 4 and 6 min of aeration at a constant rate of airflow of 29.3 cc per sec which is equivalent to 71.6 cc per sq cm per min, or 462.6 cc per sq in. per min. The aqueous solution for each test, containing 1000 cc of distilled water and 19.2 ± 0.5 mg frothing reagent, was adjusted to a pH of 6.9 ± 0.2. The volume of froth is expressed as cubic centimeter per square centimeter and is equivalent to the height of the froth column (the distance between the bottom and the meniscus of the froth). The volume of froth was obtained by multiplying the height of froth by the cross-sectional area of the glass cylinder, 24.53 sq cm. Before each test, the glass cylinder, 13, was cleaned thoroughly with jets of tap water, ethyl alcohol, tap water, cleaning solution, tap water, and finally distilled water. The cylinder with stopcock,

Jan 1, 1952

It was a pleasure listening to this paper. Gary Works' problems were a lot more extensive than the trunnion bearing problems encountered at the Weirton Steel Division. In our two-vessel shop bearing failures are critical in that with a bearing failure on an operating vessel and the second vessel under rebuild, we are down until the vessel rebuild is completed or the bearing is repaired. The first bearing problem at Weirton occurred after we had been operating three years. The failure occurred during the 8th heat following "bum-in" of the vessel. Immediate steps were taken to change the damaged float bearing without an extensive search for the reason the bearing failed. Once the campaign was run out the bearings were inspected and found to be damaged. Field checks revealed that the bearing pedestals were not properly located and as a result the freedom of the float bearing was restricted. The trunnion pin end to end dimension had decreased due to distortion and deflection in the trunnion ring. These dimensions were within tolerances. The damage to our bearing was similar to that in the exhibits from U.S. Steel-Gary Works. Steps taken to correct what was found in the field checks were as follows: 1. The pedestals were relocated to center the bearings. 2. 4" diameter pins were installed to locate the housing in the pedestals. 3. The bearing pedestals were opened up to allow the bearing housing to move slightly in the pedestal. 4. Lubrication fittings for greasing between the bearing housing and the pedestal were installed.

Jan 1, 1972

By Pol Duwez, Ellis P. Frink, Paul Pietrokowsky

Ti-Au alloys in the composition interval 0 to 66 213 atomic pct Au have been studied over a temperature range from 400° to 1500°C. A partial phase diagram has been established from micrographic and macroscopic observations. All intermediate phases, Ti3Au, TiAu, and TiAu., exhibit open melting maxima. It has been observed that small additions of gold lower the allotropic transformation temperature of titanium. The P solid solution decomposes eutectoidally to a solid solution plus Ti3Au. The solubility of gold in a solid solution decreases with temperature. THERE have been several papers in the literature pertaining to the alloy system Ti-Au. However, a comprehensive study of this interesting constitu- tion diagram has not been conducted. Previous investigations have been concerned with the crystal structure of intermediate phases or partial phase diagrams. This paper represents a partial constitution diagram, Ti-TiAu,, the first portion of an investigation of the entire binary system. Laves and Wallbaum' reported the intermediate phase Ti,Au to be isomorphous with CuAu, L12 type. In a more recent paper, Duwez and Jordan' have concluded that TiAu has an atomic arrangement which is related to Cr,Si. The intermediate phase

Jan 1, 1957

By W. R. Opie, O. W. Mole

By confining the electrolytic reduction of TiCl4 to the interior of a porous basket-cathode the electrolyte between the anode and the cathode can be kept free of reduced chlorides of titanium eliminating undesirable reactions of reduced titanium chlorides with brickwork or oxygen in the cell atmosphere. Semiwalls are not needed. Operating conditions are given and discussed. Titanium yields based on TiCl4 introduced are 93 pct. Cell voltage and amperage characteristics are adaptable to multiple cathode-series cell urmngements. EXPERIMENTS conducted in the National Lead Co., Titanium Division, Research Laboratories showed that titanium metal could be deposited in an electrolytic cell in which titanium tetrachloride was introduced through a tubular cathode.' The reduced chlorides as formed were confined to the vicinity of the cathode. They were reduced to form a cocoon-shaped growth of sponge titanium metal at the end of the cathodic tube below the surface of a sodium chloride-strontium chloride electrolyte. No diaphragm was needed.' Although high-purity, coarse crystalline metal was produced in the cocoon growth, the yields of metal removed from the cell, based on the amount of titanium introduced as TiCl4, were usually only 40 to 60 pct. The growth of the cocoon deposits was away from the cathodic tube for introduction of TiC14 toward the anode following the flu lines. The reduced chlorides of titanium diffused through the deposit and were reduced to titanium electrolytically within the deposit or on the outer surfaces. Deposition within the pores of the cocoon was detrimental to further deposition because it plugged the passages used by the reduced chlorides to diffuse away from the point of titanium introduction. As plugging due to deposition in the pores proceeded, the reduced chlorides in the center of the cocoon would force their way out by forming a channel and would escape from the vicinity of the cathode without being reduced to metal. Some work had been done previously1, 2 which indicated that if the end of the cathodic tube for introducing TiC14 was surrounded by a screen connected to the tube so that it too was cathodic, growth could be made to occur within the screen. Direction of growth was observed to be from the screen toward the point of TiCl4 introduction. Through a series of design modifications a cathode evolved which consisted of an introduction tube surrounded by a perforated metal basket as shown in Fig. 1. Modifications of this design are described in Refs. 3, 4, and 5. This basic cathode designa" was incorporated in electrolytic cells containing graphite anodes and constructed of high-silica brick refractory for containing the electrolyte (see Fig. 2). The inner crucible was surrounded by insulating brick and the entire unit contained in a welded steel shell. Suitable cooling chambers with inert gas atmospheres were devised so that the cathode could be removed from the cell without exposing the deposit to air while hot. Various alkali and alkaline earth chlorides were used as electrolytes.

Jan 1, 1961

By R. Van A. Norris

Although mechanical appliances for the ventilation of mines have been known siuce very early times (one being mentioned in Agricola's De Re Metnllica, 1657), it is only within the last forty years that such appliances have been generally used. A great number of different ventilators have been invented and used, but the varions forms of centrifugal machines having proved their efficiency, have now almost conlpletely replaced all others. Most if not all of the machines in use in this country are of this class, being either open-periphery fans, or closed, with chimney and spiral casing, of a more or less modified Guibal type. The theory of such machines has been demonstrated by Mr. Daniel Murgue in Theories and Practice of Centrifugal Ventilating Machines, translated by A. L. Steavenson. His statement may be condensed thus : Let a = orifice in a thin plate, of such area that its resistance to the passage of a given quantity of air equals the resist ance of the mine. I o = orifice in a thin plate of such area that its resistance to the passage of' a given quantity of air equals that of the machine. Q = quantity of air passing in cubic feet per minute. V = velocity of air passing through a. Vo = velocity of air passing through o. h = head iu feet air-column to produce velocity IT h, = head in feet air-column to produce velocity V,.

Jan 1, 1892

By R. W. Raymond

Under the names of Conservation, Social Justice, the New Nationalism, and Progressive Democracy, many earnest reformers are calling for a new system of Federal government to replace the one which they ascribe to our fathers, and declare to have been outgrown. They are proposing the lease by the United States of certain natural resources on the public domain, for the profit of the U. S. Treasury, instead of the sale of such resources to private citizens or associations of citizens. In the present paper, I shall try to show that this notion is neither new nor good. It is clear that the United States is owner, as well as sovereign, of public lands acquired through conquest or purchase from other nations, as it was owner of the public lands expressly ceded to it by the original thirteen States. Its policy with regard to such lands involves, therefore, two entirely distinct questions: What shall it do as owner ? and, What shall it do as sovereign ? The latter question, it must be confessed, has played but a small part in our history. All the prerogatives of sovereignty which were not explicitly conferred upon the Federal government by the original States were retained by them. The ownership or control of precious or other metals or minerals in the earth, for instance, was thus reserved to the several sovereign States. New York, South Carolina, and other States have passed laws on this subject, without regard to Federal authority. As new States have been successively admitted to the Union, the tacitly accepted theory has been, that they thereby acquired all the reserved rights of the original States. These newer States largely outnumber the first thirteen; and it is inconceivable that they would submit to any deprivation of sovereignty based on historical grounds. One of them—Texas—came into the Union by its own voluntary

Jan 1, 1913

By Walter R. Hibbard, Cyril Stanley Smith

IN 1929 one of the authors1 determined the constitution of copper-silicon-manganese alloys contailling over go per cent copper. Through a combination of circumstances the presence of the copper-silicon kappa phase was overlooked in both binary and ternary systems. In the binary system the omission has already been rectified.2,3 To establish the limits of this phase in the ternary system, the samples that had been heat-treated at the time of the original research have now been re-examined, using more careful technique. Full details of the compositions used and the temperatures and times of heat-treatment are to be found in the earlier paper.2 The etching reagent now used to distinguish the kappa phase had the following composition: hydrogen peroxide (30 vol.), 2o c.c.; water, 25 c.c.; 20 per cent potassium hydroxide solution, 5 c.c.; ammonium hydroxide (0.90 sp. gr.), 50 c.c. 'I'able I lists the newly observed structures. In virtually every case the constituents are the same as those previously recorded, except where kappa is now shown to be present as a result of the improved etching technique. X few other changes will be noted (No. 138 at 450°C., No. 147 at 550°C., Nos. 153 and 149 at 75o°C.). The change from liquid to beta in equilibrium with kappa in No. 137 at 800°C. is based upon newly heat-treated samples. The alloy is very near the solidus at 800°C. and probably there was a slight error in the old heat-treatment temperature. The isothermal phase diagrams shown in Figs. I to 6 were reconstructed on the basis of the new studies. The presence of manganese does not greatly change the composition limits of the kappa phase or cause the K-a + Y change to occur at a markedly different temperature. There is some uncertainty regarding the range of existence of beta, for alloys were not spaced very closely in composition. The proposed diagrams, however, are in accordance with the available experimental data and with the dictates of the phase rule. Theoretically necessary fields with no experimental points are delineated by dotted lines. The alpha boundaries at all temperatures are shown together in Fig. 7. This includes also some additional points on the alpha boundary at 300' and 350°C., which were obtained as a result of electrical-conductivity measurements. Two series of seven alloys with increasing manganese content but with silicon constant at 1.90 + 0.03 per cent or 2.42 ±. 0.05 per cent were cast in ingots of 3-in: diameter. These were hot-rolled, homogenized and drawn to wire, finished at 0.08-in. diameter with a 61 per cent reduction of area following annealing at 700°C. Conductivity determinations were made before and after annealing for 30 days at 300°C. or 21 days at 350°C. Figs. 8 and 9 show the change of conductivity produced by this annealing, plotted against manganese

Jan 1, 1942

By Walter R. Hibbard, Cyril Stanley Smith

IN 1929 one of the authors1 determined the constitution of copper-silicon-manganese alloys contailling over go per cent copper. Through a combination of circumstances the presence of the copper-silicon kappa phase was overlooked in both binary and ternary systems. In the binary system the omission has already been rectified.2,3 To establish the limits of this phase in the ternary system, the samples that had been heat-treated at the time of the original research have now been re-examined, using more careful technique. Full details of the compositions used and the temperatures and times of heat-treatment are to be found in the earlier paper.2 The etching reagent now used to distinguish the kappa phase had the following composition: hydrogen peroxide (30 vol.), 2o c.c.; water, 25 c.c.; 20 per cent potassium hydroxide solution, 5 c.c.; ammonium hydroxide (0.90 sp. gr.), 50 c.c. 'I'able I lists the newly observed structures. In virtually every case the constituents are the same as those previously recorded, except where kappa is now shown to be present as a result of the improved etching technique. X few other changes will be noted (No. 138 at 450°C., No. 147 at 550°C., Nos. 153 and 149 at 75o°C.). The change from liquid to beta in equilibrium with kappa in No. 137 at 800°C. is based upon newly heat-treated samples. The alloy is very near the solidus at 800°C. and probably there was a slight error in the old heat-treatment temperature. The isothermal phase diagrams shown in Figs. I to 6 were reconstructed on the basis of the new studies. The presence of manganese does not greatly change the composition limits of the kappa phase or cause the K-a + Y change to occur at a markedly different temperature. There is some uncertainty regarding the range of existence of beta, for alloys were not spaced very closely in composition. The proposed diagrams, however, are in accordance with the available experimental data and with the dictates of the phase rule. Theoretically necessary fields with no experimental points are delineated by dotted lines. The alpha boundaries at all temperatures are shown together in Fig. 7. This includes also some additional points on the alpha boundary at 300' and 350°C., which were obtained as a result of electrical-conductivity measurements. Two series of seven alloys with increasing manganese content but with silicon constant at 1.90 + 0.03 per cent or 2.42 ±. 0.05 per cent were cast in ingots of 3-in: diameter. These were hot-rolled, homogenized and drawn to wire, finished at 0.08-in. diameter with a 61 per cent reduction of area following annealing at 700°C. Conductivity determinations were made before and after annealing for 30 days at 300°C. or 21 days at 350°C. Figs. 8 and 9 show the change of conductivity produced by this annealing, plotted against manganese

Jan 1, 1942

By S. F. Ravitz

IN his excellent book on the Principles of Flotation, Wark' makes the following significant statement concerning the theory of flotation: Two questions of first-rate importance must be considered . . . First, it must be decided whether the sulfide minerals require a collector in order that they may float, or whether as has been claimed, they possess an inherent floatability and need no collector. Second, it must be decided whether the xanthate type of collector can react with or be adsorbed by the unchanged sulfide minerals themselves, or whether, as many claim, reaction with the collector is dependent upon initial oxidation of the mineral surface. In the theory of flotation there are no two questions of greater importance than these. Ravitz and Porter' presented evidence that galena can be floated without a collector, and even without any reagent, provided oxidation products are thoroughly removed from its surface. They found also that thoroughly cleaned galena floated faster when xanthate was used than when a frother alone or no reagent was used, and that, without a collector, the recovery decreased gradually upon exposure of the mineral to air. Their work, however, has met with considerable criticism. I(127).3-6 This paper is presented to answer the objections that have been raised, and to present additional data that confirm their results. EXPERIMENTAL PROCEDURE The apparatus used to provide oxygen-free conditions for flotation has been described in detail by Ravitz and Porter. An atmosphere of purified nitrogen was maintained within the apparatus; all water and solutions used were freed of dissolved air, and could be transferred where desired by the use of nitrogen pressure; nitrogen was used as the gaseous medium for flotation. The flotation cell was essentially a glass cylinder 15 cm. long and 4.6 cm. in diameter. Near the bottom was sealed a fritted glass filter, which broke up the gas into small bubbles, and 6 cm. above this filter was a side arm through which the froth overflowed. The pulp was agitated by a glass impeller, which entered the cell through a mercury seal. For each test 17 grams of galena and 75 ml. of water were placed in the cell, after which the speed of the impeller and the rate of gas flow were adjusted. Water was added gradually during the test to keep the froth level at the proper height. The mineral was prepared and cleaned in the following manner. Exceptionally pure galena was crushed by hand on a clean bucking board, screened to - 150+ 200 mesh, and deslimed on a zoo-mesh sieve with a fine spray of water. It was then boiled on a hot plate for a number of hours with several changes of the desired cleaning solution, after which both the solution and the mineral were placed in the "mineral flask" of the apparatus. The cleaning solution was drained off, and the mineral was boiled with oxygen-free water

Jan 1, 1940

ARTICLE I NAME AND OBJECT SEC. I. This Institute is incorporated under the Membership Corporations law of the State of New York; its corporate name is American Institute of Mining and Metallurgical Engineers, Inc.; and its objects are such as are stated in its Certificate of Incorporation. ARTICLE II MEMBERS SEC. 1. The membership of the Institute shall comprise four classes, namely: 1. Members; 2. Honorary Members; 3. Associates; 4. Junior Associates. All members shall be equally entitled to the privileges of membership, excepting that Honorary Members, Junior Associates, and Members and Associates whose residences shall be outside of the United States, Mexico, and Canada shall not be entitled to vote. Members and Associates residing within the United States of America, Mexico, and Canada, .and not in arrears for dues, shall be entitled to vote in person at the meetings of the Institute, or, as hereinafter provided for, by letter ballot. SEC. 2. Members shall comprise all those persons who on the third Monday of February, 1918, were members of the Institute, and in addition thereto, all those thereafter elected or transferred into the class of Members. A person to be eligible for election or transfer into the class of Members must be at least 27 years of age and must have had at least six years' employment in the practice of engineering, mining, geology, metallurgy or chemistry, during at least three years of which he must have held positions of responsibility in one or more of these fields. Graduation from the scientific course of a college, approved by the Committee on Membership, shall be considered equivalent to two years' employment, as required in the previous sentence. Employment as a teacher of engineering, mining, geology, metallurgy or chemistry, if in direct charge, may be considered a position of responsibility as specified in the second paragraph. Persons employed in research or any scientific literary work or in teaching in the scientific departments of colleges, approved by the Committee on Membership, who at the same time are engaged in consulting or in the active practice of mining, geology, or metallurgy, shall be entitled to consider the time so spent in active practice as equivalent to an equal length of time of employment in positions of responsibility, provided the work done or the positions held seem to the Committee on Membership to warrant the equivalency. The requirement of three years' employment in positions of responsibility maybe waived by the Committee on Membership in the case of persons who have done notable original work in mining, geology, or metallurgy, or have won distinction by

Jan 1, 1925

By D. J. McAdam

RESULTS of investigation of corrosion-fatigue of metals at the U. S. Naval Engineering Experiment Station, Annapolis, Md., have been discussed by the writer in several recent papers. 1.2.3.1 In those papers references were also given to the work of Haigh in 1917.6 Efforts by the writer to obtain a better understanding of some of the factors involved in corrosion-fatigue finally developed into a general investigation of the effect of time and cyclic stress on corrosion of metals. Corrosion fatigue of Metals As described in the papers mentioned, rotating-cantilever specimens, conically tapered so that the stress is nearly uniform over a length of about 1.5 in., were subjected to simultaneous fatigue and corrosion. For this purpose a stream of water was diagonally applied so as to sweep the specimen from the outer to the inner fillet and surround the stressed surface with water. The fresh water is a calcium carbonate water, the composition of which has been given in a previous paper .2 The salt water is Severn River water having a saline content about one-third that of sea water. The previous papers described results obtained with ferrous and nonferrous metals. The experiments showed that even slight corrosion simultaneous with fatigue may cause failure at nominal stresses far

Jan 1, 1928

By R. I. Jaffee, C. M. Craighead, G. A. Lenning

The effects of increasing hydrogen content, introducing a notch, and changing the strain rate on properties of titanium and one of its alloys were investigated over a range of testing temperatures from —196° to 200°C. Both high purity and commercial purity A-55 titanium were used as representative a materials, while a commercial Ti-8 pct Mn alloy was used for an a-P alloy. It was found possible to analyze the data, using the ductile-to-brittle transition temperature concept. Increasing hydrogen, the presence of a notch, and increasing the testing speed raised the transition temperature for the a materials. The presence of hydrogen and notches raised the transition temperature of the a-B alloy also. However, increasing the testing speed generally decreased the transition temperature of the a-p alloy. IN previous papers, the authors have shown that hydrogen is most detrimental to the notch-bend impact toughness of a-titanium' and to the tensile ductility of a-B titanium alloys.' These general effects have been confirmed by Kessler and co-workers," and by Kotfila and Erbin." Kessler showed that the slower strain rate in notch-rupture tests was a more sensitive measure of hydrogen embrittle-ment of a-B alloys than the tensile test. In the present paper the authors cover, with tensile and notch-bend tests, the effect of testing speed, notches, and testing temperature on hydrogen em-brittlement. High purity and commercial purity titanium, examples of u materials, and a commercial a-,f3 Ti-8 pct Mn alloy were investigated. The purpose of the investigation was to correlate the factors producing embrittlement. Materials The high purity titanium for this investigation was obtained by arc-melting crystal bar from Foote Mineral Co. into 1 Ib ingots. As-cast hardnesses for these ingots ranged from 60 to 90 Brinell. The arc-melted ingots were forged to % in. diam rods at 1470°F. These rods were swaged to & in. diam at room temperature prior to machining of the specimens for hydrogenation and testing. The commercial A-55 titanium and the Ti-8 pct Mn alloy were obtained from Rem-Cru Titanium Inc., as % in. diam rod. The A-55 titanium was hot swaged to 1/4 in. diam at 1300°F prior to machining of the specimens for hydrogenation and testing. The a-p C-11OM alloy was hydrogenated prior to hot swaging to 1/4 in. roc1 at 1300°F. Hydrogenation prior to fabrication permitted testing of the a-P alloy in the equilibrated and stabilized condition. The equilibration and stabilization treatment used was an air anneal for 1 hr at 1300°F, followed by furnace cooling to 1100°F and then air cooling. Hydrogenation was done in a Sieverts apparatus described previously.' The hydrogenation treatment consisted of heating for 1/4 to 1/2 hr at 820 °C in purified hydrogen, slow cooling to 680"C, holding 1 hr for homogenization, and rapid cooling to room temperature. Intended hydrogen levels for the a-tita-nium materials were 0.05, 0.5, 1.0, 1.5, and 2.0 atomic pct—about 15 to 430 ppm. For the Ti-8 pct Mn alloy, the intended hydrogen levels were 0.05, 0.5, 1.0, 2.5, and 5.0 atomic pct—about 15 to 1100 ppm. The material for the 0.5 atomic pct level of hydrogen was vacuum annealed prior to hydrogenation to increase the accuracy of the addition. Vacuum annealing to remove hydrogen consisted of heating for 6 hr at 820°C, and resulted in a hydrogen content of about 10 to 15 ppm. When hydrogen contents were above 0.5 atomic pct—100 ppm—the hydrogen was added without prior vacuum annealing.

Jan 1, 1957