Search Documents

By N. E. Garner

Laboratory experiments were conducted to investigate the cutting of a single diamond on limestone and shale under simulated down-hole conditions. A high-pressure chamber was modified by adding a rock-rotating device so that planing tests could be run. Weight on the diamond, diamond geometry and differential pressure across the face of the rock were varied. It was found that (I) high differential pressure reduced the volume of rock cut by the diamond at a given bit weight by strengthening the rock and changing the mode of failure; (2) a finely powdered rock left in the bottom of the grooves reduced the volume cut by as much as 50 percent; and (3) orientation of a single diamond about the axis of a drill point had considerable influence on diamond cutting efficiency. INTRODUCTION Diamond bits consist of many diamonds held in a matrix provided with water courses for fluid passage to clean, cool and lubricate the diamonds as they drill formation. Each diamond contributes its share to the overall effectiveness of a bit, but a lack of understanding of the performance of a single diamond has hampered efforts to engineer improvements in diamond bits. The need for those improvements prompted this study. This paper describes the findings of a laboratory investigation of the outting action of a single diamond where the differential pressure between the wdlbore and formation, diamond geometry and vertical force on the diamond were independently varied. The tests were conducted in a pressure chamber that provided relative horizontal motion (planing) between a rock and diamond under simulated down-hole pressure conditions. EQUIPMENT HIGH-PRESSURE CHAMBER WITH ROTATING DEVICE The high-pressure chamber used in previous rock mechanics studies' was modified for this study by addition of a rock-rotating device. The modified chamber (Fig. 1) differs from the old chamber in that the rock can be rotated to provide relative horizontal movement between the rock and the penetrator which may be a small element of a diamond or a drag bit. In this study the penetrator was a single diamond. The rock sample holder inside the chamber is mounted on a thrust bearing and is connected to the external drive mechanism by a stem that passes through two seal elements. The seal elements are needed to allow formation pressure to enter the bottom of the rock sample through a small hole in the stem. The Kapseal seal elements (Tefion boots backed by O-rings) provide low friction (hand free) even at differentials of 5,000 psi. The drive mechanism is a variable-speed transmission with a speed range from 0 to 30 rpm and an output torque of 2,800 in.-lb. A right-angle-drive gear box couples the drive to the stem. The new design has two independent pressure systems (formation and borehole) to simulate down-hole rock stress environment. Formation pressure enters from the bottom of the rock through a 6-in. diameter area, and borehole pressure acts over the remaining surface. A 14-in. layer of zero fluid loss oil-base mud poured over the top of the rock and an O-ring seal on bottom allow a differential between the borehole and formation pressures. Bayol 50 was used as the hydraulic fluid in the chamber. The differentials reported here were obtained by elevating the borehole pressure while keeping the formation pressure at zero.

By F. D. Mahone

Much crude oil, as produced from the well, carries varying amounts of water, which may be present as free water in globules sufficiently large to settle out, in time, if the fluid is allowed to stand, or as an emulsion formed by myriads of minute water particles, each surrounded and entrapped by a film of oil through which it cannot break under the action of gravity alone. Such an emulsified mixture of oil and water is commonly termed "cut oil." When such an emulsion is subjected, under proper conditions, to the influence of a high-potential alternating-current field, the minute water particles rupture the enveloping oil films and coalesce into larger water droplets this procedure continuing until all the water is freed into drops of such size that they readily settle out. This action has been photographed by the micro-moving-picture camera; under the microscope, the breaking-up of the emulsion, as described, is seen to be accomplished in a few seconds. The low power requirements of the process, from records of commercial plants, substantiate the theory that the action is that of a multitude of electrical condensers in series, rather than that of a number of conducting paths. The minute water particles serve as the metallic elements, or plates, of the condensers and the separating oil acts as the dielectric. Such surface charges as the particles may have are removed, and the intervening oil is broken, probably electrically by the voltage and mechanically by the attractive force between adjacent oppositely electrified particles. The principle of breaking up an emulsion under the influence of an alternating electric field was discovered by F. G. Cottrell and Buckner Speed, through experiments conducted, at the University of California, which resulted in a plant being installed on the property of the Lucile Oil Co. in the Coalinga field, California, early in 1909. This plant was able to reduce 14-per cent. emulsion to less than Pper cent. with commercial success. Standard Cottrell Apparatus The present standard Cottrell apparatus consists essentially of the electric treater and a settling or trap tank. The treater is a galvanized-iron tank approximately 3 ft. in diameter and 10 ft. high, which con-

Jan 1, 1924

Adams, Benjamin C., Jr., Student, Univ. of Oklahoma Norman, Okla. '36 Adams, Ernest C., Student, Univ. of Illinois 908 W. Green St., Urbana, Ill. '35 Adams, George H., Student, Colorado School of Mines Golden, Colo. '36 Adams, Robert Keller Mitchell Hotel, No. 18, Golden, Colo. '35 Afshar, Hadji Khan A., Student Box 63, Univ. Sta., Moscow, Idaho. '36 Ahrenholz, Herman William, Jr., Student, Lehigh Univ Bethlehem, Pa. '35 Alger, Robert P., Student, Missouri School of Mines & Met.Rolla, Mo. '36 Allen, Paul W., Student, Mass. Inst. of Tech Cambridge, Mass. '35 Allen, R. M., Jr., Student, Virginia Polytechnic Inst., "G" Co.Blacksburg, Va. '35 Alley, John Arnold, Student, Montana School of Mines Butte, Mont. '36 Amberger, R. H., Student, Michigan College of Min. & Tech Houghton, Mich. '35 Ambrosiani, F. Peter, Student, Michigan College of Min. & Tech Houghton, Mich. '36 Andersen, Burton Lee, Student, School of Mines, Univ. of Washington Seattle, Wash. '36 Anderson, Carlos, Student, Univ. of Oklahoma Norman, Okla. '36 Anderson, J. Wendell, Student, Pennsylvania State College State College, Pa. '36 Anderson, Joseph S. Cornelia Hotel, Ajo, Ariz. '35 Anderson, R. C., Student, Univ. of Washington Seattle, Wash. '35 Anderson, Roy A., Student, Washington State College Pullman, Wash. '35 Anderson, Willard. Student. Univ. of Oklahoma Norman, Okla. '36

Jan 1, 1936

By Paul Averitt

The U. S. Geological Survey has been actively engaged in work on coal for more than 50 years. During this long period we have released more than 300 publications containing information about coal and coal reserves, including details on the thickness, distribution, and quality of coal, and the structure and stratigraphy of the coal-bearing rocks. We have also cooperated with state surveys on many similar publications. For many areas these reports are the only reliable published data on our resources of coal. During the last several years we have substantially increased our activities above the wartime low. We now have field work in progress, or reports in preparation, on 13 detailed mapping projects distributed as follows: 1. Pennsylvania anthracite field 2. Casselman Basin, Md. 3. Leslie County, Ky. 4. Deep River field, N. C. 5. Coosa field, Ala. 6. Powder River field, Mont. 7. Spotted Horse field, Wyo. 8. Yampa field, Colo. 9. Paonia field, Colo. 10. Trinidad field, Colo. 11. Durango field, Colo. 12. Chaco River area, N. M. 13. Lewis and Thurston County fields, Wash. For two of these areas; the Paonia field, Colo., and the Coosa field, Ala., we have published recently preliminary reports, and final reports are in preparation. In addition, we are nearing completion of a coal reserve study of Montana, and are beginning similar studies in several other states, as part of a program of revising our estimate of national coal resources on the basis of presently available data. Factors Involved in Making Estimates Our responsibilities include detailed field mapping to secure information on areas of outcrop of coal beds, their range in thickness, nature of roof rock, amount of overburden, correlation of the beds, stratigraphy and structure of the coal-bearing rocks, and the preparation of coal reserve figures based on these data. The computation and estimation of resources of coal in the ground, like that of resources of other mineral commodities, involves consideration of many additional purely geological factors that can be appraised best through such regional studies. Regional variations in the thickness and texture of rocks overlying and underlying coal beds, for example, give evidence as to the probable position of the edges of the basin of coal deposition, or may aid in the delineation of sand-filled channels that sometimes cut out coal beds. It is apparent that the detailed field studies, in which data are gathered, are the basis for coal reserve studies, and in our present program these two phases of work are being carried on together. Previous Coal Reserve Estimates For many years we have been aware

Jan 1, 1950

By B. Ladanyi

The problem of rock behavior under concentrated loadings has been the subject of a number of studies in the past and has been receiving increasing attention by rock mechanics investigators in recent years. Its application covers various fields, but main interest in its solution has arisen in connection with the problems of drilling, bearing capacity, and rock testing. These widely different purposes and fields of interest probably have been one of the reasons why, in spite of the large amount of published experimental data and several theoretical studies, there are still many points which need further clarification. Another reason for this situation undoubtedly is due to the fact that the rock behavior in indentation is complicated by a great number of influencing factors. Experimental evidence shows that, depending on the rock type (mechanical properties, porosity), environment (ambient effective pressure, pore fluid, temperature), and the type of loading (indenter shape, initial embedment, load level, loading rate), the rock response to indentation may vary within very large limits. The widely different rock behavior has made it impossible up to now to treat the problem with a consistent single mathematical theory, but has required instead a series of simplified models covering only certain most important events in the failure sequence. As far as the theory of rock indentation is concerned, this chapter does not add much new information. Its main purpose is, however, to state the indentation problem in a general manner and to indicate which points need to be studied in more detail before its definite solution is attempted. Also, since excellent reviews of the state-of-art of rock indentation in drilling have recently been given,1-4 this will not be repeated here, and only references pertinent to the points of the problem under study will be quoted. The theoretical part of this study attempts to give a quantitative evalu-

Jan 1, 1972

By Louis Stott

IT is well known that the oxide of beryllium was identified as a new "earth" in 17971 and the metal first isolated in 18272. The history of the many difficulties encountered by early investigators, the laboratory achievements of Lebeau3, Fichter4 and Oesterheld5, and the eventual development of methods for commercial production are well covered in the literature, particularly in the authoritative published work of Siemens and Halske6 reviewing their comprehensive investigation of the element. Accordingly it has seemed desirable to restrict this paper to the properties and uses of beryllium and its alloys.

Jan 1, 1936

By C. D. Stahl, E. E. Templeton, R. F. Nielsen

It has been customary, in predicting saturation changes, to use the Leverett fractional flow formula", obtained by eliminating the unknown pressure gradient from the generalized Darcy equations for the separate phases. The formula presents difficulties in the case of counterflow, since the "fractional" flow may be negative, greater than unity, or, in the case of a closed system, infinite. Recently, it has been shown by several authors that the corresponding equations (with capillary pressure and gravity terms) for actual flow of the phase may be used just as well. These equations are in agreement with Pirson's1 statement that, if the two mobilities differ considerably from each other in a closed system, the flow is largely governed by the lower value. The present study was undertaken because of an apparent lack of experimental data on gravity counter-/low with which to test the theory. A 4-ft sand-packed tube in a vertical position was employed. Electrodes for determining saturations by resistivity were spaced along the tube, one phase being always an aqueous salt solution. Air, heptane, naphtha, or Bradford crude oil was used for the other phase. A reasonably uniform initial saturation was set up by pumping the phases through the system, alter which the tube was shut in and saturation profiles obtained at definite intervals. Cumulative flows over certain horizontal levels were obtained by integration of the distributions; hence, differentiation of the cumulative flows with respect to time gave instantaneous flow rates. To compare experimental and theoretical flow values, capillary pressures were assumed given by the final saturation-distribution curve. The upper part corresponds to the "drainage" region and the lower part to the "imbibition" region, where trapping of the nonwetting phase occurred. While calculations indicated that the capillary pressure saturation function and, probably, the relative permeability saturation functions changed during the segregation, the relation of the measured rates to saturation distributions are in general accord with the frontal-advance equation. It appears that the Darcy equations, as modified for the separate phases, are generally valid for counterflow due to density differences. The usual method of predicting saturation changes, which involves a continuity equation and the elimination of the unknown pressure gradient from the flow equations, should therefore be applicable. However, the need for advance knowledge of drainage and and imbibition "capillary pressures" and relative permeabilities during various stages presents difficulties. INTRODUCTION The present study was undertaken because of a seeming lack of experimental data relating to vertical counterflow of fluids of different densities in porous media. In particular, it was desired to determine whether data obtained from these laboratory tests were in accordance with certain mathematical treatments of counterflow which have been proposed. The gravity "correction" has been incorporated into the flow equations (and, hence, into displacement theory) nearly as long as both have been used. field4 and laboratory5 data have generally borne out the validity of the theory as applied, for instance, to downward displacement by gas, with all fluids moving downward. However, the modifications for counterflow have only recently been pointed out. 2-3 It has been customary to use fractional flow rates instead of actual flow rates in displacement calcuIations. In the case of counterflow, this results in negative values, values greater than unity and, when rates are equal and opposite, in infinite values. As pointed out by Sheldon, et a1,3 and by Fayers and sheldon,2 actual flow rates may be used just as well. The fact that these may be of opposite signs for the two fluids does not present any difficulty.

By T. E. Eagan, W. R. McCrackin

IN dealing with segregation in babbitt, and its effect on the final cast structure, which is a bearing, it is obviously impossible to cover all of the compositions manufactured. Each composition, of course, will exhibit certain specific types of segregation. However, as examples,, two compositions of babbitt are presented: one a tin-base of well-known analysis and the other a lead-base, which in the past few years has found wide usage. Bearings usually are cast either statically or centrifugally; therefore the effect of these two methods on segregation is presented. EXPERIMENTAL PROCEDURE A slab of babbitt 1/2 in. thick by 5 in. wide and 17 in. long was cast, using a book mold with the long edge vertical. An A.S.T.M. grade 2 babbitt was used (3.5 per cent copper, 7.5 per cent antimony, remainder tin), to which 0.10 per cent tellurium had been added. Unfortunately, no metal without tellurium was available. The mold to hold the babbitt was heated to approximately 300°F., the temperature being judged by the babbitter. The pouring temperature of the babbitt was 875°F. (470°C.). One slab was made by allowing the babbitt to cool without stirring. The other slab was stirred during the entire cooling cycle. This stirring consisted of a vigorous churning or puddling into the mold until complete solidification had taken place. Three samples were removed from these slabs. One was taken at the extreme bottom, another half way to the top, and another at the extreme top, all at the center of the width. Chemical, macroscopic and microscopic examination was made of all samples. Table I shows the chemical analyses obtained at the described positions [ ] in the slab. The analyses show no serious amount of gravity segregation. Microscopic examination from edge to edge of the slab showed little change in structure. From top to bottom there was a progressive coarsening of the grain size in the stirred slab but little change in the slab that was not stirred (Fig. I). No definite exhibit of segregation could be detected. In line with our experimental study on the tin-base babbitts, we cast an almost duplicate slab using A.S.T.M. Alloy No. 15, containing 0.9 to 1.25 per cent tin, 14.75 to 15.5. per cent antimony, 0.80 to 1.25 per cent arsenic and 0.4 per cent copper. The slab was 16 in. long and 3/8 in. thick, cast with the long side vertical. One slab was allowed to cool normally and the other was stirred continually during cooling. The pouring temperature of the babbitt was

Jan 1, 1944

By Fred B. Brost

In 1976, a decision was made to install a conveying system to transport ore 10.3 km (6.4 miles) from the new Eisenhower mine to Twin Buttes. The system, supplied and installed by Cable Belt Ltd., of England, represents a radical departure from conventional conveyor systems. The driving tension is applied through two endless wire ropes while the belt acts only as the carrying medium. Features of the system are a single 2240-kW (3000-hp) drive and a 60° angle bend. Construction was completed in two years and full production was attained alter several mouths operation.

Jan 12, 1979

By M. A. Bryant, J. C. Goodwin, T. B. Faddies, L. D. Kornze

The Mercur Gold Mine is located 56 km (35 air miles) southwest of Salt Lake City in north central Utah; In July 1981 Getty Mining Company made the decision to put Mercur into production. The first gold bar was poured in April 1983. This paper provides details on: 1) the history of the camp, 2) past production, 3) geology of the deposit, 4) the exploration and development program, 5) ore reserve estimates, 6) detailed geologic pit mapping, 7) production blasthole sampling techniques and 8) the use of geostatistics (kriging) in handling assays and gold extractions to produce the required mill feed.

Jan 1, 1985

By Murray F. Hawkins

One problem of reservoir engineering is the early estimation of the size of newly discovered reservoirs. Often these reservoirs are the expansion type in which sizeable pressure drops occur incident to the production of small fractions of the oil reserve, above the bubble point, and a material balance equation may be solved to find the reserve. The early form of this equation' considered only the compressibility of the oil. Later Hall2 showed that the compressible nature of the formation rock is a significant factor in production above the bubble point, and he presented a new equation which includes a formation (rock) compressibility term. This note presents a further extension of the material balance equation as applied to volumetric, unsat-urated reservoirs above the bubble point by including a term for the presence and compressible nature of the interstitial water. DERIVATION OF EQUATION During a decline in average reservoir pressure, ?p ?p, — p1 the initial reservoir volume V,, will decrease to some value V, due to the reduction in pore volume as a result of a decline in the hydrostatic pressure within the formation, and v, = V,, [l — cr ?p]......(1) The formation compressibility c, is expressed in terms of change in pore volume per unit pore volume per psi. Simultaneously the connate water within the formation expands from an original volume V,, = S,V,, to a new volume V,, V, = s,v,, [I + c,npl.....(2) The difference [Vp — V,] is the hydrocarbon pore volume at pressure p and may be equated to the volume of the remaining oil, or [N — N,] B, = V,,, [I - C~A;] - S,.Vpi [l + cwnjl.........(3) But the initial oil in place in terms of the initial reservoir volume, connate water, and formation volume factor is Ilividing Equation 3 by Equation 4 eliminates V,, to give,

Jan 1, 1956

By D. E. Etter, J. E. Selle

The Pu-Ce phase diagram was determined by differential thermal analysis, metallography, and elechm-nricroprobe analysis. The dingram is chararterized by a eutectic with extensive solid solubility in the cubic Phases of both cerium and plutonium. No intermediate phases were found. Cerium is soluble in e plutonium to 16.0 at. pet Ce at 626OC nnd in d plcltoniurn to 23.0 at. pet at 613 "C, decreasing to 17.5 at. pet at room temperature. No solubility in the a, ß, or ? phases was jound, and the mininum cerium required to stabilize 5 plutonium to room temperature is 3.2 at. pet. The maximum solubility of plutonium in 6 cerium is 19.5 at. pet at 721OC, and the maximum soluhility of plutonium in ? cerium is 34.5 at. pet. Invariant points in the system are: a) eutectic at 626oC, L16.5 = E Pu16.0 + y Ce65.5; b) peritectoid at613oC, e Pu13.5 -y Ce65.5- d Pu23.0. AS part of a program aimed at the determination of the phase equilibria in the Pu-Ce-Cu ternary system, preliminary investigations were made of the three binary systems. A survey of the Pu-Ce binary system by differential therma1 analysis indi- cated several areas of disagreement with the published diagram,' primarily in the shape of the liquidus surface. Consequently, a thorough investigation of the system was undertaken, and this report presents the results of the study. EXPERIMENTAL PROCEDURE Three methods of investigation were used: differential thermal analysis (DTA), metallography, and analysis with electron-microprobe X-ray analyzer (EMX). The EMX analysis was particularly useful for the determination of solvus lines. The DTA method was most useful for the determination of the liquidus curves. Metallography complemented both of these techniques. Materials. The cerium metal used for most of this work had a freezing point of 805°C. This material showed 15°C premelting, and was found metallographically to contain some unidentified in~lusions.2 The temperature of premelting is defined as the point at which the DTA curve breaks away from the base line, analogous to a curve obtained from a solid-solution alloy. Several compositions were prepared near the cerium end of the diagram with higher-purity material which had a freezing point of 800°C. etallographic analysis showed this material to be relatively free of inclusions and only 8°C premelting was observed. Major impurities were found by spectrographic

Jan 1, 1964

By A. S. Richardson

AIR conditioning, or air cooling, for the improvement of ventilation in the Butte mines has come into increasing use during the past 10 years. In part, the methods practiced have been described in previous publications of the Institute, but some improvements on earlier methods have been made and a number of new features have been developed. This paper is presented as a record of progress made, and for the sake of completeness describes all general features of the work. The need for air conditioning in the ventilation of mines in the district arises from the fact that the temperature of the ground and mine water has shown a very great increase with increase in mining depth, and has now reached a maximum of slightly over 130ºF. The most difficult part of the ventilation problem is the maintenance of temperature and humidity of a satisfactory standard in the working places, especially on the lower levels. Although ordinary ventilation is adequate to maintain good conditions in most of the working places it is subject to a number of limitations at great depth. Most important among these limitations is that with increase in depth the air becomes heated before it reaches the working places, both by compression from increase in atmospheric pressure and by heat transferred to it from rock at high temperature, so that its capacity for lowering temperatures is greatly reduced before it reaches the operating zone. Increasing depth of mining also increases the distance traveled by the air in its passage through the mine, and this causes a corresponding increase in resistance to air flow, so that there is greater difficulty in maintaining even the same volume in circulation. Thus, in the face of a demand that the ventilating system have a very much greater capacity to remove heat from the mine, the tendency is for that capacity to diminish. The only evident alternatives were (I) the opening of additional air shafts to increase the volume of air in circulation, (2) an extension of the existing system that would be subject to the same limitations, or (3) the adoption of an entirely different method such as air cooling. Fortunately for an economic solution of the problem, the mean annual temperature of the surface atmosphere at Butte is about 40°F., with very low relative humidity in summer, so that there is unlimited natural cooling power at a temperature range adaptable to air-conditioning methods. METHODS Two similar methods of air conditioning are used, as necessitated by service requirements and dependent upon the equipment available. In one, which is the more important and has the greater cooling capacity, water is circulated in a closed circuit, and, alternately, first absorbs heat from warm mine air and then dissipates it in the surface atmosphere by cooling at a cooling tower. The second

Jan 1, 1941

[Trans. No. Place Date Vol. Page 1. Wilkes-Barre, Pa.*...May, '71.. 1 3 2. Bethlehem, Pa Aug., '71.. 1 10 3. Troy, N. Y Nov., '71, , 1 13 4. Phildelphia, Pa Feb., '72.. 1 17 5. New York, N. Y. May, '72 120 6. Pittsburgh, Pa Oct., 7. Boston, Mass Feb., '73.. 1 28 8. Philadelphia, Pa.* ... May, '73.. 2 3 9. Easton, Pa Oct., '73.. 2 7 10. New York, N. Y Feb., '74.. 2 11 11. St. Louis, Mo.* May, '74.. 3 3 12. Hazleton, Pa Oct., '74.. 3 8 13. New Haven, Conn.... Feb., '75.. 3 15]

Jan 1, 1940

By Richard H. Jahns

Gem materials, comprising those minerals and closely allied natural substances used for personal adornment, for the fashioning of ornamental objects, or for other decorative purposes, have been valued in human commerce for thousands of years. Amber, jet, natural glasses, and at least 15 mineral species were sought and used by primitive man, and most of the materials in common use today were known well before the time of Christ. Their variety is remarkably great, and the traceable relationships among their respective sources, modes of occurrence, properties, and histories of production, preparation, and valuation are extremely complex. Their uses have been affected by numerous shifts in fashion, and from time to time by superstition, by decrees of church and state, by personal interpretations of religious significance, and by various presumptions concerning medicinal value and influence on human behavior (Ball, 1935, 1950; Kunz, 1913; Pogue, 1915, Whitlock, 1946). Thanks to their durability, portability, and relative scarcity, some gem stones have been employed as media of exchange, and the investment value of the more precious stones has long been recognized and exploited, especially in Asiatic and European countries. Demands for gem materials have stimulated trade among various peoples for centuries, and they also were responsible for much early geographic exploration. During more recent times they have prompted numerous geological studies and a considerable amount of research on the growth and properties of crystals. Apart from decorative uses, some naturally occurring gem materials also are employed directly in numerous fields of industry. Substances that are manufactured for gem or industrial uses are termed synthetic gem materials; most of these correspond in composition and crystal structure to certain minerals found in nature. Imitation materials are those whose use is based upon their resemblance to substances of different composition and greater intrinsic value. Gem stone is a designation commonly restricted to those materials suitable for personal adornment, and the complementary term ornamental stone is applied to the remaining materials not used industrially. This distinction is arbitrary and somewhat inconsistent, owing to numerous geographic differences and historical shifts in end uses. Further, there is a complete gradation between the category of ornamental stones and that of dimension stone. Substances that lose their identity in use are excluded from the gem category; thus a transparent crystal of beryl would not be classified as a gem stone if it were processed as a source of beryllium metal. The adjectives precious and semiprecious have been employed as a means for distinguishing different gem materials on the basis of recognized value. Diamond, emerald, ruby, and sapphire consistently have been regarded as precious stones, and in cut form they commonly are referred to as the noble gems. Opal, pearl, turquoise, and chrysoberyl also have been classed as precious at various times. In recent years, however, it has been increasingly recognized that no satisfactory distinction can be based upon assessed value or any group of specific properties, and now all gem stones normally are referred to as precious. Indeed, the tendency is to extend this term to include many of the so-called ornamental stones, and the designation semi- precious has been essentially discontinued. Unlike most mineral commodities of economic value, gem materials are little altered in processing for end uses. Some stones are used in essentially their natural form, and most are reshaped and polished without significant changes in their fundamental properties. Thus the preparation of gem and ornamental stones is intended chiefly to emphasize or enhance

Jan 1, 1975

By W. Spencer Hutchinson

The experiments described in this paper were undertaken primarily for the purpose of measuring the quality of work done in screening and sorting in American concentrating-mills for Prof. Richards' work on Ore-Dressiag. For this purpose a series of samples of screened and sorted products was obtained from four different mills, and a plan was devised for sizing these products, and for tabular and graphic representation of the results. The results, together with discussions as to their significance, so far as they serve to interpret the quality of mill-work, have already been published in the above-mentioned work, and it is not the purpose of this paper to duplicate the work, except so far as is necessary to explain and illustrate methods and appliances. The sizing of coarse products was clone by sifting on screens of sheet-metal with round punched holes. These holes ranged in size from 64 mm. to 0.5 mm. in diameter. Below the smaller limit, punched metal, suitable for this work, was not obtainable, and the sizing was carried on by sifting on woven wire-sieves. The finest woven wire-cloth obtainable gave a hole 0.073 mm. square, and the finest silk bolting-cloth pave a pentagonal hole with an average diameter of 0.069 mm. Even these very fine screens served no useful purpose in sifting certain of the very fine classifier-products, of which all, or nearly all, passed through the finest screen. A new adaptation of a method of settling and decantation with water in beakers was therefore worked out, and by this means the sizing mas carried down to grains of a diameter as small as 0.012 mm. Description of Apparatus and Manipu1ntion.—Sieves of sheet-metal with round punched holes were used as far as practicable, chiefly because, as already explained, the primary object of the experiments was to test mill-work, and the mills had all used

Jan 1, 1905

By John T. Galey

A combination of two factors in addition to the current Federal drilling and price regulations reduced by 120 from I942 the number of new wells completed in southwestern Pennsylvania during the year. No new prospective area was found comparable to the Armbrust gas pool, Westmoreland Co., which accounted for a seventh of the last year's drilling, and it is considered doubtful whether, even if such a field had been discovered, the drilling contractors, who have been seriously affected by the manpower shortage, could have drilled many more wells than they did during the year. New wells totaling 445 were completed for a combined footage of over 1,250,000 Dry holes numbered 131 and had a footage of nearly 400,000. Old wells drilled deeper total 55, of which 17 were found nonproductive. Shallow Development Oil Oil completions yielded an initial of only slightly over one hundred barrels from 21 wells for about the same per well average as that of a year ago. However, 65 bbl. of this total came from two wells in two new strikes. The footage drilled of nearly 33,000 gives an average of nearly I00 ft. less per well than a year ago. Two old wells drilled deeper had a combined initial of only 4 bbl. The largest oil well of the year, 40 bbl., was found in the Speechley (U. Dev.) sand at a depth of 3492 ft. in German township, Fayette County. The location is several miles east of the nearest oil production hut as the area that could be occupied by a pool is fairly well delimited by drilling, the extent of this production would not appear to be large. The other notable oil production was found in the Dunkard (Penna.) sand, Cumberland township, Greene County, at a depth of 1065 ft. Here the first well had an initial of g bbl. and the second 25 bbl. However, a third proved dry, and as this area is also delimited by drilling, the pool doubtless will be of small area. Gas Gas completions yielded an initial of slightly over one hundred million cubic feet per day and new wells, totaling 303, account for all but four million of this volume. Old wells drilled deeper, numbering 35, found gas. The per well average in new drilling of approximately 320 M cu. ft. is nearly 165 M cu. ft. less than a year ago and the total footage is slightly over 830,000, which is about a quarter of a million feet less than in 1942. Average rock pressure of new completions is approximately 365 lb. per sq. in. The entire volume of new production is from the Upper Devonian or higher stratigraphic horizons. In Allegheny County, the grestest activity was in Forward and Plum townships. Wells there account for more than one half the completions. One large well was drilled in Forward township and an open flow of 3.623 million cubic feet was found in an old Gantz (U. Dev.) sand area. The top of the sand was encountered

Jan 1, 1944

By John T. Galey

A combination of two factors in addition to the current Federal drilling and price regulations reduced by 120 from I942 the number of new wells completed in southwestern Pennsylvania during the year. No new prospective area was found comparable to the Armbrust gas pool, Westmoreland Co., which accounted for a seventh of the last year's drilling, and it is considered doubtful whether, even if such a field had been discovered, the drilling contractors, who have been seriously affected by the manpower shortage, could have drilled many more wells than they did during the year. New wells totaling 445 were completed for a combined footage of over 1,250,000 Dry holes numbered 131 and had a footage of nearly 400,000. Old wells drilled deeper total 55, of which 17 were found nonproductive. Shallow Development Oil Oil completions yielded an initial of only slightly over one hundred barrels from 21 wells for about the same per well average as that of a year ago. However, 65 bbl. of this total came from two wells in two new strikes. The footage drilled of nearly 33,000 gives an average of nearly I00 ft. less per well than a year ago. Two old wells drilled deeper had a combined initial of only 4 bbl. The largest oil well of the year, 40 bbl., was found in the Speechley (U. Dev.) sand at a depth of 3492 ft. in German township, Fayette County. The location is several miles east of the nearest oil production hut as the area that could be occupied by a pool is fairly well delimited by drilling, the extent of this production would not appear to be large. The other notable oil production was found in the Dunkard (Penna.) sand, Cumberland township, Greene County, at a depth of 1065 ft. Here the first well had an initial of g bbl. and the second 25 bbl. However, a third proved dry, and as this area is also delimited by drilling, the pool doubtless will be of small area. Gas Gas completions yielded an initial of slightly over one hundred million cubic feet per day and new wells, totaling 303, account for all but four million of this volume. Old wells drilled deeper, numbering 35, found gas. The per well average in new drilling of approximately 320 M cu. ft. is nearly 165 M cu. ft. less than a year ago and the total footage is slightly over 830,000, which is about a quarter of a million feet less than in 1942. Average rock pressure of new completions is approximately 365 lb. per sq. in. The entire volume of new production is from the Upper Devonian or higher stratigraphic horizons. In Allegheny County, the grestest activity was in Forward and Plum townships. Wells there account for more than one half the completions. One large well was drilled in Forward township and an open flow of 3.623 million cubic feet was found in an old Gantz (U. Dev.) sand area. The top of the sand was encountered

Jan 1, 1944

By C. W. Gibbs, E. K. Parks

In 1929 the Standard Oil Company of California commenced the development of a device for obtaining temperatures and pressures in flowing and shut-in wells and of suitable running equipment for such a recorder. Although simple in principle, the recorder has required much experimental work in its development. The various problems have now been solved to such an extent that it is believed that the apparatus affords a sturdy and reliable means for obtaining information regarding depth pressures,—apparatus that may be turned over to a well gang for routine operation. As an example of the rough usage the device will withstand a recent incident may be cited. Owing to failure of the lowering line at the conclusion of a run a recorder was dropped some 6300 ft. through 2 1/2-in. tubing filled with gassy oil. The device was fished out undamaged and with the pressure record intact, although the instrument had been subjected to a pressure greater than 2300 lb. per sq. in. for some 24 hr. after impact at bottom. Description of Recorder The instrument is of the continuous recording loaded spring type (Fig. I). Temperature is not recorded continuously but is obtained by maximum recording thermometers in an auxiliary thermometer well. The entire instrument assembly, from bottom of the recorder to top of the socket, is 6 1/2 ft. long and weighs less than 25 lb. The maximum outside diameter of the recorder shell is 1 1/4in., and all attachments need be no larger. This permits lowering the device inside 2-in. tubing. The operating principle is simple. The well pressure acts upon a piston A resisted by the extension of spring B. The spring deflection is recorded by a stylus C upon paper within the recording drum D. Springs.—To improve accuracy at lower maximum well pressures five interchangeable spring assemblies are used. These have maximum pressure ranges of from 250 to 5000 lb. per sq. in. Piston diameter is the same in all cases, and each spring is designed for a deflection of about 5 in. for maximum pressure loading. A complete spring assembly there-

Jan 1, 1934

By A. W. Schlechten, R. P. Abendroth

Equilibrium H2S/4 ratios were determined as functions of temperatunz and composition in a hydrogen recirculation apparatus. A high-temperature solid solution exists in the range two-phase regionfrom TiS 1.96, to TiS1.30, Various thermodynamic quantities were calculated from the data. COMPOUNDS in the titanium -sulfur system have not receiyed much attention in the past, probably because they do not occur naturally in the earth's crust. However, titanium-sulfur compounds have been used in various metallurgical processes. The U.S. Bureau of klines' studied the formation of ti- tanium-sulfide mattes from charges composed of rutile, pyrite, and carbon, with the resulting sulfide matte being chlorinated to form titanium tetrachlo-ride. Fishel, Roe, and Ellis' investigated the de-sulfurizing action of titanium in steels, and Schwarz and Koster studied the preparation of metallic titanium from the sulfide using aluminum and magnesium reduction. The thermodynamic properties of some of the compounds present in the titanium-sulfur system may prove to be of some use in the consideration of future processes using these sulfides, and would

Jan 1, 1960