Search Documents

By Donald E. Grimes

In conjunction with Inland Steel&apos;s development of lead-bearing steels possessing improved machin-ability because of tellurium and/or selenium additions, it was decided to determine liquidus and solidus temperatures in the Pb-PbTe-PbSe sub-ternary system. With the exception of alloys in the PbTe-PbSe system, it is believed that no previous study of this subternary has been performed. Thermal analysis was employed in a general survey of the subternary. In addition to PbTe, PbSe, and pure lead, ten ternary compositions were selected at intervals of ten at. pct. Sixty-gram alloys were prepared by sealing an appropriate mixture of the elements in quartz crucibles with a central thermocouple-well under a vacuum of less than 10 p. All three elements were 99.999+ pct pure with only trace impurities detected by spectroscopic examination. After the alloys had been heated at least 20°C above the liquidus in a Kanthal furnace, cooling and heating curves were obtained. Two or more cooling curves were employed both for the determination of each alloy liquidus and for the solidus of those al- loys containing greater than 50 at. pct Pb. Cooling rates were 0.5° to 3.5°C per min during the 5 min immediately prior to the start or end of solidification. For those ternary alloys containing 50 at. pct Pb, the solidus was determined from heating curves. Temperatures were measured with a Pt/Pt-10 pct Rh thermocouple which was calibrated in the same apparatus against the freezing points of zinc (A. D. MacKay—99.999 pct), antimony (A. D. MacKay-99.999 pct), and copper (ASARCO—99.999+ pct) both before and after the experimentation. The only interruptions in the continuous strip-chart recording of the temperature occurred for brief periods at significant points of interest when direct readings were made with a Rubicon Type B potentiometer sensitive to * 1 µv. The average liquidus and solidus temperatures obtained in this investigation are listed in Table I together with probable errors based on the accuracy of the thermocouple calibration and the reproduci-bility of the data. No chemical analyses of the alloys were performed because the synthetic or as-charged compositions were felt to be reliable. The melting points obtained for PbTe (924.7° ± 0.7°C) and PbSe (1084.0° ± 0.6°C) compare favorably with recent findings of other investigators.&apos;-&apos; As indicated in Table I, both the liquidus and solidus temperatures increase as selenium replaces tellurium for a constant atomic percent lead. As a result, the ternary liquidus and solidus temperatures for a given percent lead lie between the corresponding binary temperatures published in the literature. It should be noted that those ternary alloys containing 50 at. pct Pb exhibit a relatively narrow liquid-plus-solid region (<80°C) when compared with alloys containing greater than 50 at. pct Pb. Alloys with 60, 70, or 80 at. pct Pb not only have a much wider liquid-plus-solid region (>500°C) but also exhibit considerably lower and approximately constant solidus temperatures which thus form a virtually isothermal solidus "plane" slightly below the melting point of pure lead (327.3°C). For these alloys

Jan 1, 1965

By James F. Kemp

In earlier gears, the custom prevailed of regarding the anthracite basins as cases of folding with slight development of faulting. Folding is so pronounced and, in the eastern and western Middle Fields, at times so violent, that the inference was a natural one and led to the widespread impression that practically all the disturbances of the seams could be explained in this way. The cross-sections and maps prepared forty or more years ago for the Second Geological Survey of P ennsylvania, by Mr. Ashburner under Prof. J. P. Lesley, exhibit little else than folds.&apos; So far as I can discover faults fail in the charts, except in one small case in the Henry colliery near Plainsville on the outskirts of Wilkes-Barre. Some years ago, while spending a day or two in Wilkes-Barr, under the guidance of R. V. Norris, I looked over some recent and accurate cross-sections of a numbcr of the large collieries and was deeply impressed with the peculiar behavior of some of the seams and the intervening shales. Thus, a seam might present a small, more or less overturned fold, rising 30 to 50 ft. (9 to 15m.) above its general course, and yet the movement would be taken up in the overlying shales, so as hardly to be noticeable in the seams next above or below. These and similar anomalies, especially when shown with the accuracy of engineer&apos;s surveys, possess great scientific and practical interest, bearing as they do, not alone on coal mining, but on theoretical geology and the actual behavior of strata under great compressive stresses. In preparation for the semicentennial meeting of the Institute, an effort was therefore made to secure some of the most interesting sections for presentation to the members. The collection of illustrations here shown is mainly due to Douglas Bunting of the local committee, to whom and to the contributing companies acknowledgments are due. The illustrations are taken from all four of the main basins, but are chiefly from the portions nearest Wilkes-Barre. The first are in the

Jan 1, 1922

By Samuel S. Wyer

THE following description of methods for conducting gas-producer tests is probably the first attempt to give the subject an analytical, thorough and comprehensive treatment. In some cases where tests have been made, the methods have been so unsystematic and ambiguous that it has been impossible to secure comparable results. To eliminate this difficulty, the following provisional code of gas-producer tests-which has some resemblance to the code of boiler-trials of the American Society of Mechanical Engineers-has been developed. The primary object in testing a gas-producer is to determine whether the producer is working satisfactorily or, what is the same. thing, to see if the efficiency is as high as it should be with the type of producer in question, and also to find out if the composition of the resulting gas is adapted to the work it has to do. In order that the test shall be of any value, it must be thorough and comprehensive, and must be conducted with skill and care. When so conducted, the test will reveal the economy of the producer; and, by making suitable changes, the efficiency will often be increased very much. As a result of the tests made by Jenkins, 1 the efficiency was raised from 56.2 to 71.2 per cent. This shows the large saving that may frequently be made in the fuel-consumption by studying the results of a careful test.. The log of the test, given in Fig. 1, shows that, just as soon as the temperature became regular, the percentage of CO, decreased and that of CO increased.

Mar 1, 1905

By E. G. Dean

A method of top slicing has been devised at the Miami Copper Co.&apos;s mine at Miami, Aria., which differs radically in some ways from the customary methods of top slicing. The area of that section of the orebody in which top slicing is used is about 800 ft. square. The ore, while for the most part soft, is, nevertheless, considerably harder than the capping. The latter is siliceous, seldom containing any clay or other binding material, and breaks into fine particles so that it runs like sand if given the opportunity. Because of these facts, and because the ore is above the average grade of the mine ore, it has been mined by top slicing. Haulage levels are opened up 150 ft. apart, vertically, with two sub-levels between at 50-ft. intervals, to facilitate the putting up of ore chutes. These sublevels are used during slicing for distributing air in the ventilation system. On the haulage level the drifts are spaced on 50-ft. centers, and raises along these drifts are also spaced on 50-ft. centers, except the incline raises as hereafter noted. The raises are cribbed where necessary. Where the wear will be excessive, 1/4-in. iron plates are spiked to the top of every third set of cribbing, for its protection. When top slicing was first used, an attempt was made to carry a slicing face from fifty to several hundred feet long. Timber and other supplies were brought in through long drifts from an auxiliary shaft. Great difficulty was experienced in keeping these drifts open, the side pressure breaking the posts and the top weight breaking both caps and posts. Furthermore, the men could not work efficiently while these drifts were being repaired. The slicing faces advanced irregularly, due to varying conditions, and in many ways the results were not all that could be desired. It was then decided to divide the slicing area into blocks 200 ft. square and this was later changed to 250 ft. square. At the center of each block a two-compartment raise is put up as a supply raise, the compartments being 2 ft. 6 in. and 4 ft. by 4 ft. 4 in., the smaller being used as a manway. Station sets of 12 by 12 timber with

Jan 1, 1917

By T. W. Martin, T. J. Crocker, J. M. Goris

The current technology of large rock conveyors is reviewed. Based on this investigation two large rock conveyor concepts have been developed and a test facility investigation designed and fabricated. The USBM will test these concepts along with loading and transfer points for handling mine run rock material up to 1.5 m (4.9 ft) in size. An evaluation of open pit mining systems using large rock conveyors documents substantial cost savings when compared to truck haulage.

Jan 1, 1983

By J. H. Henderson, H. J. Ledbetter, N. B. Gove, J. D. Griffith

INTRODUCTION The results of a series of laboratory flood tests using liquid Iso-butane to displace refined oils from test cores are pre- ented and interpreted on an empirical bask. The study Revealed the similarity of the miscible liquid displacement to that of the immiscible-fluid displacement mechanism. The efficiency of the iso-butane flood decreased markedly as the oil Viscosity increased. but the effect of injection rate on the effectiveness of the primary production stage was negligible over the range investigated. The presence of free-gas saturation prior. to iso-butane breakthrough increased the volume of iso- Butane required to recover a given percentage of the oil present. Injection of liquid i.e.-butane prior to water follicle sculpted in a marked improvement in oil recovery by the water flood. INTRODUCTION The production of petroleum is often enhanced by the injec-1i1)n of extraneous fluids into the reservoir. It has been suggeited that the injection or cycling of a wet gas or a liquefied petroleum gas would he instrumental in increasing the effic.ienr!; of oil recover! to a greater degree than the commonly injected fluids. dry pas and water. Although instances of injection of light liquid hydrocarbons are not unknown, a systrmatic recording of the result is unavailable and superfi- cially, the practice gives the impression of being economicaIIy unsound. For specific types of displacement, analytic: solutions have been advanced which aid in understanding the physical mechanisms involved. However, there is no generalized theoretical concept which permits adequate prediction of displacement efficiency from a knowledge of readily measured reservoir rock and fluid properties. The Buckley-Leverett approach to oil displacement by an immiscible phase is an admirable analysiy of that type of mechanism. Dykstra and Parsons have introduced a useful concept in their evaluation of the role of the mobility ratio and its merit in rationalizing displacement phenomena. Everett, Gooch and Calhoun3 in their report on the effect of viscosity ratio and miscibility have pointed out the lack of a comprehensive theoretical approach and the desirability of investigating the mechanism of miscible-miscible displacement. In lieu of a well-developed theory concerning miscible-111isci1)le displacement and in view of the scarcity of engineering information on actual LPG injection trials, the limited program of laboratory experimentation described below was undertaken. OBJECTIVES The original broad objectives of the program, to study the oil recovery process using LPG as the displacing phase, defined the direction and scope of the laboratory tests. The specific objective. of the experimentation were to evaluate

Jan 1, 1953

By T. B. Massalski, C. S. Barett

THAT metals and alloys of the body-centered-cubic structure tend to become unstable at low temperatures is so nearly universal that any exceptions are worthy of special attention. Studies of the exceptions may disclose unrecognized examples of metastability or may shed light on the nature of some of the factors that stabilize the body-centered-cubic phase. Among the structurally analogous body-centered-cubic 3/2 electron compounds, the ß-phase in the Cu-Zn system deserves further attention for, although this phase is known to undergo partial mar-tensitic transformation on cooling below room temperature to the temperature of liquid nitrogen when the composition is less than about 42 wt pct Zn, it does not transform on cooling .when there is more than this amount of zinc present.1-4 The present authors recently found that an alloy containing 48.35 wt pct Zn could be transformed, however, if deformed severely at room temperature or lower temperatures.V his discovery led to the suggestion that the jerky flow of ß-brass single crystals6 and some of the unusual temperature variations of the yield strength and hardness are due to strain-induced transformation during the tensile tests. The present investigation is an extension of that work to cover the entire available range of compositions of Cu-Zn ß-phase alloys and certain interesting compositions of the ß-phase in the Cu-Zn-Ga system. Particular attention is given to the structure of the transformation product resulting from cold work, which is found to vary with alloy composition, and to the temperature range in which transformation can be induced in the various alloys. The composition limits of the body-centered-cubic phase in the Cu-Zn system, based on a recent review by Raynor7 and the precision determinations of Beck and Smith: are shown in Fig. la; in the ß region the alloys are disordered and in the ß region they are ordered. The rate of ordering is so rapid that a high degree of order is found in any of these alloys immediately after quenching. Experimental The nine binary and four ternary alloys of this investigation were prepared from cathode copper (99.99 pct purity), electrolytic zinc (99.99+ pct), and gallium (99.98+ pct). All alloys were cast in transparent Vycor tubing, homogenized at temperatures between 800° and 890°C, and quenched in water. Ternary alloys were cast in small amounts (-5 g) to predetermined compositions to fall along a line of constant electron concentration in the ternary system. Changes of weight during the casting operation of the ternary alloys were not greater than 1 part in 2500 from the intended nominal weights and therefore their compositions were accepted without chemical analyses. All binary alloys were cast in larger amounts (100 to 150 g), homogenized, and hot rolled after preheating to 800°C. The central portion of the rolled strip of each alloy was annealed for eight days and quenched in brine. All binary alloys were analyzed chemically. The compositions, heat treatments, and metallographic appearances of all alloys are tabulated in Table I. Various samples were subjected to heat treatment or cold work at several temperatures and were then examined metallographically or by means of X-rays. Specimens about 6x6x3 mm in size were examined metallographic ally to confirm the presence of the ß-phase after quenching. Cold work was introduced by fastening each sample between two pieces of steel, cooling the assembly to the desired temperature, and transfering it rapidly to a vise where moderate or severe compression was immediately applied. Cold working at liquid helium temperature was done by a chisel-shaped tool mounted on an X-ray spectrometer, described elsewhere.% A!! metal-

Jan 1, 1958

By J. H. Richards, G. Derge, W. Peifer

A WIDE Variety of metallurgical defects in steel have commonly been attributed to the presence of excessive amounts of hydrogen. These defects include flakes in rails and forgings, cracks in welds, and blisters in enameled ware, They have been related to hydrogen largely by circumstantiat evidence because the proper sampling and analysis of steel for hydrogen has been known to be difficult and because no general agreement has existed with regard to the relative suitability and accuracy of available methods. The need for a direct approach to these problems has been widely recognized. This general situation has been well described in the publications of the British committee on the Heterogeneity of Steel Ingots,&apos; and current approaches to the problem were reviewed in a recent symposium of the AIME.I2 The plans described by the present authors at that meeting have now matured satisfactorily and will form the basis of this paper. The principal object of this paper will be to describe the methods of sampling and analysis which have been developed and to illustrate the usefulness and limitations of these methods by citing their application to a specific problem, The first problem selected for investigation was the behavior of hydrogen in rail steel. This was chosen because the occurrence of shatter cracks in rails has received a great deal of study over a long period of time. The defect can be controlled by the expensive procedure of slow in However, it may be hoped that a better understanding of the factors influencing the hydrogen content of rails will lead to a more efficient control of this problem. Rails provide a good starting point for a more general study of hydrogen in steel because they provide a cross-section large enough to develop cracks, Yet small enough for convenient handling and sampling. Rails were also selected because they arc made from plain carbon steel and it was felt that the initial work should not be complicated by the effects introduced by alloying elements. The considerations which determined the original planning of this study should be reviewed. The inherently complex nature of most hydrogen problems requires that a large amount of data must be collected for any particular case. This in turn means that any analytical procedure should be as rapid and simple as possible. The same objective of speed is indicated by the fact that it may finally become desirable to use hydrogen analysis in process control. It is also known that hydrogen is highly fugitive and that any procedure which facilitat~s early analysis of the sample without prolonged or irregular storage has distinct advantages. The most important previously reported methods of analysis may be classified into three general groups: (I) Vacuum fusion, (2) Vacuum extraction (without melting), (3) Total combustion.

Jan 1, 1949

By G. Derge, W. Peifer, J. H. Richards

A WIDE Variety of metallurgical defects in steel have commonly been attributed to the presence of excessive amounts of hydrogen. These defects include flakes in rails and forgings, cracks in welds, and blisters in enameled ware, They have been related to hydrogen largely by circumstantiat evidence because the proper sampling and analysis of steel for hydrogen has been known to be difficult and because no general agreement has existed with regard to the relative suitability and accuracy of available methods. The need for a direct approach to these problems has been widely recognized. This general situation has been well described in the publications of the British committee on the Heterogeneity of Steel Ingots,&apos; and current approaches to the problem were reviewed in a recent symposium of the AIME.I2 The plans described by the present authors at that meeting have now matured satisfactorily and will form the basis of this paper. The principal object of this paper will be to describe the methods of sampling and analysis which have been developed and to illustrate the usefulness and limitations of these methods by citing their application to a specific problem, The first problem selected for investigation was the behavior of hydrogen in rail steel. This was chosen because the occurrence of shatter cracks in rails has received a great deal of study over a long period of time. The defect can be controlled by the expensive procedure of slow in However, it may be hoped that a better understanding of the factors influencing the hydrogen content of rails will lead to a more efficient control of this problem. Rails provide a good starting point for a more general study of hydrogen in steel because they provide a cross-section large enough to develop cracks, Yet small enough for convenient handling and sampling. Rails were also selected because they arc made from plain carbon steel and it was felt that the initial work should not be complicated by the effects introduced by alloying elements. The considerations which determined the original planning of this study should be reviewed. The inherently complex nature of most hydrogen problems requires that a large amount of data must be collected for any particular case. This in turn means that any analytical procedure should be as rapid and simple as possible. The same objective of speed is indicated by the fact that it may finally become desirable to use hydrogen analysis in process control. It is also known that hydrogen is highly fugitive and that any procedure which facilitat~s early analysis of the sample without prolonged or irregular storage has distinct advantages. The most important previously reported methods of analysis may be classified into three general groups: (I) Vacuum fusion, (2) Vacuum extraction (without melting), (3) Total combustion.

Jan 1, 1949

By Eugene Leonardon

THE search for oil has required, and without a doubt supplies, a tremendous amount of information on the structure, composition, physical properties, and history of sedimentary rocks. The earliest and most complete source of knowledge is the sample or core of the rock itself, the uses of which are well known. The purpose of this paper is primarily to discuss a new method for obtaining these cores, and to illustrate its use in connection with electrical logs. Most cores have been obtained through a special adaptation of rotary drilling, and the results have been remarkably good, considering the mechanical problems involved. Unfortunately, because of the time and expense, this method cannot be used for the entire length of the drill hole. Even though ingenious contrivances have been evolved in order to reduce the time spent in round trips, such as wire-line coring equipment, mechanical coring still remains too expensive to be carried out con-tinuously. In practice, therefore, one is finally compelled to estimate the probable depths of the more interesting horizons and, allowing a wide margin of safety, to core through those sections only. It is true also that interesting results have been obtained by examining the cuttings brought to the surface by the mud circulated in the well during the process of drilling. Be that as it may, the inescapable fact remains that key horizons may be passed inadvertently, for one reason or another, while the drilling operations are being performed. The only continuous record of the formations encountered is that furnished by electrical surveys. Obviously, it would be desirable to make the electrical survey first and to take the samples from the wall of the hole according to the indications on the electrical log. In this way, it would be possible to core only the exact sections desired, eliminating the otherwise inevitable estimates as to the point at which to start coring, and thereby reducing to a minimum this expensive operation. At the same time this method would provide a maximum&apos; of useful samples.

Jan 1, 1939

By Eugene Leonardon

THE search for oil has required, and without a doubt supplies, a tremendous amount of information on the structure, composition, physical properties, and history of sedimentary rocks. The earliest and most complete source of knowledge is the sample or core of the rock itself, the uses of which are well known. The purpose of this paper is primarily to discuss a new method for obtaining these cores, and to illustrate its use in connection with electrical logs. Most cores have been obtained through a special adaptation of rotary drilling, and the results have been remarkably good, considering the mechanical problems involved. Unfortunately, because of the time and expense, this method cannot be used for the entire length of the drill hole. Even though ingenious contrivances have been evolved in order to reduce the time spent in round trips, such as wire-line coring equipment, mechanical coring still remains too expensive to be carried out con-tinuously. In practice, therefore, one is finally compelled to estimate the probable depths of the more interesting horizons and, allowing a wide margin of safety, to core through those sections only. It is true also that interesting results have been obtained by examining the cuttings brought to the surface by the mud circulated in the well during the process of drilling. Be that as it may, the inescapable fact remains that key horizons may be passed inadvertently, for one reason or another, while the drilling operations are being performed. The only continuous record of the formations encountered is that furnished by electrical surveys. Obviously, it would be desirable to make the electrical survey first and to take the samples from the wall of the hole according to the indications on the electrical log. In this way, it would be possible to core only the exact sections desired, eliminating the otherwise inevitable estimates as to the point at which to start coring, and thereby reducing to a minimum this expensive operation. At the same time this method would provide a maximum&apos; of useful samples.

Jan 1, 1939

By J. B. Newkirk, W. G. Martin

Oxidized cobalt powder is known to have a magnetic hysteresis loop which is asymmetric with respect to the magnetization axis. The experiment described herein shows that the orientation relationship between the basal plane of hexagonal cobalt and the oxide which forms upon it at 400°C is {111}ux//{100.1 }co <110>ux//<11.O> This orientation relationship allows a magnetic interaction between the antiferromagnetic oxide and the ferromagnetic substrate which could account for the offset hysteresis loop. Oxidized nickel powder has a symmetrical hysteresis loop and so is apparently not influenced by any magnetic interaction between metal and oxide. The orientation of the oxide (cubic) was found to be identical with that of the nickel substrate when the oxide forms on a polished surface parallel with {111} Ni. IN 1956 W. H. Meiklejohn and C. P. Bean discovered that fine particles of cobalt which had been prepared in a certain way have a magnetic hysteresis loop which in a strong field is asymmetric relative to the magnetization axis.&apos; The cobalt powder exhibited this unusual magnetic property only after it had been oxidized in air or oxygen; it lost the shifted hysteresis loop when the oxide was reduced in hydrogen. X-ray and neutron diffraction&apos; experiments showed the presence of cobaltous oxide (COO) and hexagonal cobalt in samples exhibiting the biased hysteresis loop and specifically showed no indication of any other compound with the exception of mercuric oxide.* The magnetic hysteresis loop becomes symmetrical above the Nee1 temperature (paramagnetic state) of COO. Therefore, it was concluded that the anomalous magnetic behavior is associated with the influence of cobaltous oxide upon the metallic cobalt. It has been proposed that crystallographic coherency may exist between the cobalt and a plane of some antiferromagnetic material which has unbalanced spin distribution and sufficient magnetic anisotropy to hold its spin in the direction which existed when the specimen was cooled. COO has these properties. Therefore, Roth&apos; has suggested that cobaltous oxide may form with a {111} plane parallel and coherent with the basal plane of the hexagonal cobalt metal and proposed that, as consequence of the antiferromagnetic interaction between COO and the underlying cobalt, the magnetization direction in oxidized fine Co particles may be ro-lated from the easy c-direction.2 Such a relationship, he proposed, would explain the observed magnetic effect in oxidized cobalt powder. The main purpose of this study was to determine the orientation relationship, if any, between the basal plane of cobalt and the oxide which forms upon it. Attempts to produce a film of COO which was strong enough to be handled were not successful. However we did succeed in making a film of CoCo2O, which was strong enough to be removed from the cobalt substrate and mounted on an electron-microscope grid. Because of the close structural similarity of COO and CoCo2O, we believe the orientation relation found for CoCo2O, on cobalt probably also holds for COO on cobalt. The epitaxial relationship of NiO and Ni also was investigated. To date no shifted hysteresis loop has been observed with nickel powder. However, the similarity of atomic array in cobalt and nickel leads to the prediction that a {111} of NiO may be parallel with a (111} of nickel. Experimental Method Cobalt-Cobalt Oxide—A coarse-grained specimen of a (hexagonal) cobalt was prepared by allowing a large crystal of fee cobalt to transform slowly at 400°C. The crystal was then cut to expose a surface parallel with the basal plane. A back reflection Laue X-ray photograph showed that the 00.1 plane was within 2" of the cut surface. The surface was mechanically polished and then electro polished in 85 pet orthophosphoric acid after which the crystal was held for 30 min at 400°C in air. During this heat-treatment the surface darkened slightly due to the oxide film which formed. The film was not thick enough to give an X-ray diffraction pattern, even by a glancing-angle technique. Glancing-angle electron diffraction was not possible either, owing to the interference of the electron beam with the high magnetic fields which exist at the 00.1 surface of the cobalt. However, it was possible to make an electron-diffraction photograph of the oxide film by stripping it from the cobalt substrate using the method described later. By maintaining reference marks carefully, it was possible to preserve the orientation relationship between the stripped film and the substrate on which it was formed. The oxidized surface of the crystal was first covered with a 1 pet solution of collodion (cellulose nitrate) in amyl acetate. When the film was dry, small rectangles were scored on the surface with a needle point. The specimen was then repolished

Jan 1, 1959

By G. A. Stamboltzis, N. Arbiter, C. C. Harris

Fracture under low-velocity free-fall and double impact and under slow compression have been investigated. The pattern of breakage and the size distribution of resulting fragments of sand-cement and glass spheres have been determined. Photoelasticity methods were used to simulate the stress distributions in free-fall impact in order to explain the observed patterns of breakage. Oblique fracture planes, occurring only in free-fall impact, develop along lines which coincide with the trajectories of maximum compression as determined by mathematical analysis. Breakage efficiencies for different modes of fracture were compared for both types of spheres. For the same specimen and loading system, static loading and low-velocity dynamic loading induce geometrically similar stress fields resulting in reasonably similar fracture patterns and shapes of fragments. This work had its origin in a desire to understand three fundamental processes involved in autogenous comminution: namely; free-fall impact, double impact, and slow compression. To simplify the investigation, it is preferable to reduce the entire multi-stage fracture process to its most elementary form; that is, to study products resulting from a single-stage operation, such as the breakage of a specimen under single fracture conditions. The goal of this research is to study the energy utilization in the single fracture of brittle specimens and to relate the pattern of breakage and the resultant fragment size distribution with the nature of the material, the specimen size, the manner of load application, and the rate of loading. Published works on single fracture have mainly been concerned with tests on large (> 1-in.) irregular mineral pieces, especially coal and coke. These were mainly friability tests employing a single blow on closely sized pieces. More recently, small mineral specimens in the sieve range and glass spheres have been investigated.5-7 Kick8 has reported free-fall and double impact tests with large large cast-iron, cement, and clay spheres. The establishment of a minimum breaking height independent of size in the free-fall impact tests, and the direct proportionality between the minimum work required for fracture and the volume of the specimen in double impact tests were used by Kick as an experimental proof of his classical law of "Proportional Resistances." In the present work, spherical shapes were chosen because of their simple body geometry and consequent impact and stress field symmetry. Because the study involves several physical principles in connection with brittle-fracture, it may be of interest in fields where the strength of materials is of importance. APPARATUS The equipment for the free-fall impact testing is illustrated in Figs. 1 and 2. This consisted of a massive (17 x 17 x 3-in.) hard steel plate onto which specimens were dropped and a specimen release mechanism which could be set at any desired height up to 10 ft above the plate so that the impact velocity could be varied up to about 25 ft per sec. Double impact breakage is characterized by two points of loading situated at opposite poles. For this mode of breakage the apparatus was modified (Figs. 3, 4 and 5) so that a falling mass provided an impact of predetermined magnitude on a specimen resting on the plate. A spring-loaded device operated immediately after fracture to arrest the falling mass and to record its residual kinetic energy. Precautions were taken to avoid secondary breakage. Slow compression tests were performed on a conventional hydraulic testing machine, the specimen being held between two hardened parallel bearing blocks. In the case of glass spheres, carbide bits were used. Photoelasticity studies were performed on two-dimensional models held in a loading frame equipped with a force gauge (Fig. 6). The models were viewed in a polariscope and isochromatic fringe patterns were recorded photographically. SPECIMENS Sand-Cement Spheres: A series of sand-cement spheres were prepared by molding in spherical glass flasks.

Jan 1, 1970

By A. Martens

When I was honored with an invitation from the American Institute of Mining Engineers to present a paper at the Chicago meeting on the microstructure of iron, I hesitated about accepting, as the short interval that would remain at my disposal, after other pressing matters had received attention, could not but seriously affect the work of preparing such a paper. Unfortunately my fears have been realized and my work is neither completed, nor yet as comprehensive as I should desire. Mindful of my promise, however, and recognizing that 1 have reached a point where the results of my researches may prove suggestive, I am led to present them now, trusting that this brief explanation map secure indulgence for whatever deficiencies the paper may disclose. So far as my knowledge of published memoirs and treatises extends, microscopy cannot yet be said to possess a really firm foundation. In few cases only has any systematic development of the methods of investigation been undertaken, and broad gaps remain to be filled. It is not yet possible, therefore, to give a complete survey of the field, or, indeed, to supply a text-book on microscopic metallography. As Mr. F. Osmond, of Paris, a distinguished member of our profession, has undertaken to prepare for the Chicago meeting a historic review of the work actually accomplished I need not touch on that branch of the subject; but before entering upon my special theme, it may not be out of place for me to introduce certain explanations, as furnishing reasons for the course 1 have hitherto pursued, and to offer some suggestions for the further development of the methods of microscopic investigation. In microscopic metallography, the examination has to be conducted principally with incident light. Objectives of low power, in which the distance between the front lens and the abject is considerable, are adapted for directly incident light, and in such cases the relatively great depth of the image renders it possible to examine

Jan 1, 1894

By Albert E. Ketler

Introduction – The introduction of computerized monitoring and control (M/c) equipment into the U.S. coal mining industry may prove to be of truly revolutionary proportions in the 801s.Many of you are aware that the British have developed and have been using such sophisticated M/C equipment for performing production and safety related tasks in their coal mines for nearly a decade. The benefits of M/C systems in the mining industry are usually separated into those which improve productivity, and hence make money for the company, and those which improve safety, and hence cost money. The economic benefits of M/C are startling for the production related functions such as for monitoring and controlling conveyor belts, de-watering pumps, electrical power distribution, and the like. It doesn&apos;t take much analysis to show that hundreds and even thousands of tons of coal don&apos;t get mined every time a belt shuts down or when power is out due to circuit breakers tripping for any number of reasons. A flood, caused by a malfunctioning pump which goes undetected for lack of feedback monitoring of pumping parameters, can destroy literally millions of dollars worth of mining equipment. The M/C system would be justified or not based on whether or not the productivity benefits balanced the cost within a timespan commensurate with the return on capital philosophy of the company. The safety related benefits are easily underestimated or ignored completely and the purpose of this paper is to under-score some of these benefits, as well as to review the application of M/C to the coal mining industry. The companies involved are Transmitton Ltd of England and Minetics Corp of Pittsburgh, Pennsylvania. Transmitton is probably the most experienced manufacturer of M/C equipment in the world having some 200 installations to its credit. Minetics is the marketing and manufacturing arm for Transmitton in the U.S.A. and is responsible for all aspects of distribution and service. Plans are underway for manufacturing of the Transmitton hardware for U.S. sales to be transplanted into U.S. subcontractors by 1981. Thus our coal mining industry will benefit from British technology, but without the delays and additional costs usually involved in international shipments.

Jan 1, 1981

By James Douglas

At this last meeting of our Institute for the year 1899, it is appropriate that we should look back at the past. To review the century&apos;s progress in the exact sciences and the resulting arts that fall within the scope of our labors is beyond my ability. But I wish to draw your attention to some phases of that progress, almost as important, which lie within the zone of sociology, touching at so many points the domain of applied technology. One of these is suggested by the library of technical literature which this century has produced —not the least important contribution to which is our own Transactions. The nineteenth century has witnessed the beneficial spread of democracy in politics. Under the impulse, to no small degree, of the same spirit, there has grown up a brotherhood of fellow-workers and a sense of fellow-ownership in the secrets of nature. Though the Patent Office has assumed such proportions as to hare become a source of national revenue, and a multitude of inventors, great and small, are seeking through its agency to secure some pecuniary profit from their devices, there is even greater eagerness among both interested and disinterested workers in the field of technology to publish their observations, and even their discoveries, and to give them to the world without remuneration. The motives influencing the great body of writers who, without any pay, use the technical journals and such media of communication as our Transactions, in order to give to the brethren of their craft the results of

Jan 1, 1900

By W. M. Raynor

LARGE quantities of "midnight oil" have been consumed by researchers in attempting to develop a process to produce cold ductile zirconium at low cost. The tantalizing facts that zirconium is a bright, silvery, tarnish-proof metal and is 2 1/2 times as abundant in the earth&apos;s crust as copper, and thirteen times as plentiful as lead have resulted in much speculation on uses, ranging from automobile radiator grills to kitchen sinks. but unfortunately no low-cost process of producing it has so far been found. In the case of zirconium, we cannot say that "virtue is its own reward" for the principal virtues of the metal, namely, corrosion resistance at ordinary temperatures and ability to absorb gases at high temperature, are the very characteristics that defeat all of the usual recovery methods such as sintering, plating, or direct chemical reduction. The only method giving a pure metal sufficiently low in oxides, nitrides, etc. to be truly cold-malleable is the one developed by Van Arkel and DeBoer in 1925. This process involves decomposition of zirconium tetraiodide in contact with a hot filament and pre

Jan 1, 1947

By Francis Foley

Small cracks in a plane normal to the axis of steels are found to be prevalent around the water hole of drill steels that have been in service for an unknown period of time. Cracks are not found on the exterior surface of the steels nor to any noteworthy extent even in the water holes of new drill steels. Undulations and serrations are found in the surface of the water hole in new steels; it is in the bottom of such defects that cracks appear to develop in used steels. The occurrence of the more serious of these cracks at the point in the steel to which it has been heated for forging or hardening is thought to account to a great extent for failures in that region. DURING the past, year, we have investigated the cause of 88 per cent, of the failures by breakage near the bit end of some 1-in. hollow, hexagon, drill steel used in a metal mine. This breakage in the region of the bit end of the steel was peculiarly interesting because we have been led to believe that breakage is most prevalent at the shank end of drill steels near the place where the steel is gripped in the chuck of the machine. Records from the mine showed, also, that the breakage was much more frequent in the short lengths of large gage than in the longer steels; this is shown graphically in Fig. 1. Because the shorter lengths of steels are usually those that have been made from broken pieces of long steels or from steels that have worn down in service, rarely being made from new stock, those who are wont to suspect steel of tiring and crystallizing in its old age through fatigue are quite apt to see in this instance an argument in favor of their idea. As usual, a careful examination of these steels reveals defects of a character hardly to be overlooked in favor of such a cause. The steel in question was rolled with a sand core and was of the usual drill steel composition: Carbon 0.85 per cent., manganese 0.60 per cent., silicon 0.25 per cent., phosphorus 0.02 per cent., and sulfur 0.02 per cent., with the exception that in some specimens there was vanadium, not exceeding 0.20 per cent.

Jan 3, 1924

By Robert I. Jaffee, Bruce W. Gonser, Eugene M. Smith

THERE has been little investigation of the gold-germanium binary alloys. Haughton1 does not mention any work on the system. In a review article commemorating the fiftieth anniversary of the discovery of germanium, E. Einecke2 mentioned a gold germanium eutectic at 24 atomic per cent Ge (10.4 weight per cent) melting at 359°C., but did not give the source of his information. From measurements of electrical conductivity, J. 0. Linde3 estimated that at least o.6 weight per cent germanium is soluble in gold. The recent availability of germanium in this country in commercial quantities has led to interest in its properties and its alloys. This study is part of a program of investigation on germanium alloys; work on ternary alloys involving germanium and gold will be reported later. In this investigation, the composition and melting point of the Au-Ge eutectic reported by Einecke has been found to be substantially correct. Eutectic composition has been placed at 12,0 per cent germanium, however. An alloy of 10.4 per cent Ge, Einecke&apos;s value, was found to have a few gold dendrites in it. The eutectic temperature has been determined as 356.0 ± 0.5°C., slightly less than the temperature of 359°C reported by Einecke. The liquidus curves and the solid solubility of germanium in gold have been determined, and are shown in Fig. I. MATERIALS AND ALLOYING The germanium used in this investigation was prepared by the Eagle-Picher Lead Co. from pure germanium oxide, by reduction in clay crucibles with sodium cyanide. The regulus is quite pure, assaying over 99.9 per cent Ge. High-purity gold obtained from Handy and Harmon was used. Alloying was carried out in graphite crucibles in an atmosphere of purified hydrogen. The temperature was brought up to 1050° to 1100°C., and the metal was allowed to freeze in the crucible. Prepared in this way, the gold dendrites in hypoeutectic alloys were somewhat segregated at the bottom and sides of the ingot, and on the hypereutectic side the lighter primary germanium tended to gather at the top. Most of the alloys were made from virgin metal. Low-germanium heats were made by alloying pure gold with the eutectic. Melting losses were consistently a few milligrams or less, and the composition could safely be taken from the intended analysis. The 30 per cent and 50 per cent germanium heats for thermal analysis were made in part from remelted higher germanium heats, and they may be off composition as much as one per cent. Because of the high cost of materials, the weight of heats for thermal analysis were 15 to 20 grams and heats for metallographic, X-ray, and hardness specimens were 2 to 4 grams.

Jan 1, 1945

By J. R. Guard

Development of electrical power in coal mining has been an outstanding example of adaptability. It has accommodated itself to new inventions, changing mining methods, increasing demands, increasing safety requirements and many other new conditions. With the appearance of the continuous miner in the mining machinery picture, those engineers interested in the application of electricity to mining have been thinking about what new combination of electrical apparatus will best suit this newcomer. It is the purpose of this paper to discuss the relative costs of supplying d-c versus a-c power to mining equipment with particular reference to continuous miner setups. Assume that a-c power will be delivered to the mine at some high voltage suitable for transmission to the various substation locations. Typical voltage for this purpose is 4000 volts. The problem then is to change the power to some kind of power suitable for driving the motors of mining equipment. For safety and other reasons the voltage to be delivered to the motor terminals must be under 600 volts.

Jan 1, 1950