Search Documents

By R. L. Stone

None of the currently used methods of testing bentonites as binders for strengthening iron ore pellets is entirely adequate by itself. Since more knowledge was needed about 1) which properties of bentonite most affect pellet strength, and 2) the precise mechanism by which strengthening is produced, attention was paid to possible new techniques for rating bentonites. With the structural nature of bentonites — in particular, the montmorillonite component — the possibility of rating bentonites on the basis of zeta potential was investigated. These bentonites were also rated by conventional tests and measurements, including colloid content, barrel yield, pH, chemical analysis and physical tests on green and dry pellets. A mechanism for pellet bonding based on electro-kinetic forces between the bentonite and the iron ore concentrate appears to be feasible. In pelletizing, from 6 to 18 lbs of bentonite is added per ton of concentrate to give strength to the green and dry pellets. In some operations even more bentonite than is required for strengthening purposes must be added for moisture adsorption to pennit balling of the concentrate. Since bentonite is thus a major item in pelletizing, more knowledge about the way in which bentonites act as binders and better ways of rating this ability would help in the difficult job of selecting the right bentonite for a given concentrate. The fact of the matter is that although several methods are in current use for testing bentonites, none of these methods are consistently foolproof. For example, a given bentonite may rate high by several standard tests yet turn out to be a poor binder, and of course the reverse also occurs. Actually, more knowledge is needed about 1) which properties of bentonite most affect pellet strength, and 2) the precise mechanism by which strengthening is produced. In this study attention is therefore paid to possible new techniques for rating bentonites. With the structural nature of bentonites as a starting point, we investigated the possibility of rating bentonites on the basis of the zeta potential, i.e., the electrokinetic ootential on the montmorillonite colloids — the main component of bentonite binders. The zeta potential technique was applied to a range of commercial bentonites from several areas in the U.S. and abroad. These bentonites were also rated by conventional tests and measurements, including:

Jan 1, 1968

By Jean-Jacques Prompsy, J. S. Rinehart

Some time ago a study was initiated at the Colorado School of Mines in an effort to arrive at a better understanding of the stress fields developed within drill bits under dynamic loading and the influence that these stress fields could have on the failure of the bits. Particular emphasis has been given to the influence that bit shape has on the establishment of highly localized, potentially destructive stress inhomogeneities within the bit. The study has been divided into three phases involving three velocity regimes: impacts at very low velocities, 0 to 20 ft/sec, a velocity range in which dynamic effects are just beginning to be found; impacts at velocities ranging from 20 to several hundred ft/sec, a range commonly encountered in practical drilling operations; and impulsive loading through the detonation of explosives, a region in which the dynamic effects are greatly exaggerated and made more identifiable. The ultimate objective is to provide basic data which will enable the mitigation through judicious design of the frequency and severity of these transient concentrations of intense stress, thereby prolonging and increasing drill efficiency. This paper presents results of the third phase of this study — the development of a better understanding of the dynamics and mechanics of failures caused by transient stress-wave interactions. The impulsive loading or transient waves in these experiments were generated by detonating small explosive charges placed on the ends of Plexiglas cylindrical rods terminating in truncated cones. Under such intense loading, dynamic effects are greatly exaggerated and, hence, made more identifiable. The explosion generates a high-intensity transient stress disturbance which moves through the rod, reflects from surfaces which lie in its path, and establishes momentarily narrow regions of high concentrations of stress where failure of fracture may occur. The peregrinations of these waves, their interactions and their effects have already been described in the literature (see, for example, Refs. 1 and 2). The locations and extent of the regions quite apparently are strongly dependent on specimen shape, making it possible through judicious shaping of specimens to relocate the highly stressed regions, minimize their extent, or eliminate them entirely. These experiments were designed, first, to identify more clearly the vulnerable regions in geometries relevant to drill-bit design and, then, to modify these regions in a predictable way by changing specimen shape. Through this latter process, it is anticipated that better bit design might evolve. The specimens used in the experiments were cylindrical rods, 1 1/2 and 1 1/8 in. in diameter, ended by a truncated cone, with the cone angles ranging from 45° to 130°. Upper cone face diameters were 1/2, 3/4, or 1 in. A small plastic-covered electric blasting cap detonated on the axis of the specimen produced the spherical shock wave. The detonators used were Olin Mathieson No. 6, which induced into the rod a transient saw-toothed stress disturbance of about 3-microseconds duration, corresponding to a wave length of 0.3 in. in the Plexiglas. Five distinct systems of fracture were observed: (1) along the axis of the rod, a lower system of fractures, the cracks focusing around one point for specimens having cone angles of 80° and 90° and, as the cone angle was increased, spreading downward; (2) just above these fractures, an upper system of fractures composed of horizontal cracks observable in some specimens but not of any appreciable extent; (3) a third system of axial cracks still above the latter, observable in the small cone-angle specimens; (4) in the upper part of the specimen, a system of radial fractures extending from the blasting point; and (5) circular spalling due to reflection of the wave on the boundary of the cylinder. Only the first three systems, the axial fractures, are examined here. LOWER TENSILE FRACTURE SYSTEM The first, lower system of tensile fractures, shown in the photograph of Fig. 1, was observed in almost all of the specimens. It was due to the reflected tensile wave coming in from the boundary of the cylinder as shown in Fig. 2. The reflected wave was cylindrically convergent and focused

By Walter Herd

Fox the past eight years No. 2 mine of the Cumberland Railway & Coal Co., Springhill, Nova Scotia-a subsidiary of the Dominion Coal Co., Ltd.-has had an unenviable reputation for bumps. As the workings extended in certain directions under a greater cover, these bumps increased in severity and it became apparent that some change in the system of extraction was necessary if the mine was to continue to operate. In September, 1924, following several fatalities resulting from bumps, the Mines Department of Nova Scotia requested from the U. S. Bureau of Mines the services of George S. Rice, Chief Mining Engineer of the Bureau, to report on the conditions then prevalent in No. 2 mine, Springhill. This request was promptly and courteously granted. Mr. Rice made a full investigation and a comprehensive and helpful report, which is embodied in the 1924 Annual Report of the Department of -Public Works and Mines, Nova Scotia. Prior to 1925, the room and pillar method was employed and in January of that year (there being a cessation of work from March to August due to labor troubles) longwall retreating on the west side, on a limited scale, and in a small section on the east side of the mine was started. The major portion of the east side was not operated on this system till August, 1926, as there was developed a considerable area ready for pillar extraction between an arbitrary boundary and a point up to which bumps of any consequence, had not been experienced. In the interval development work for longwall retreating below the 5900-ft. level was vigorously- pushed. This longwall retreating system was suggested by Mr. Rice as a possible remedy and was heartily endorsed by the company officials. This paper describes the conditions and happenings subsequent to Mr. Rice's report and more especially the results with the longwall retreating system of mining under the peculiar circumstances pertaining to mining. No. 2 Seam, Springhill, at depth, and records the 'conclusions which experience with several severe bumps under this mode of extraction would suggest. Except where necessary to make the paper intelligible as an entity any duplication of Mr. Rice's report will be avoided.

Jan 1, 1929

By David Donoghue

THE. years 1901, 1910, and 1924 may be considered as the beginning of new eras in the history of the oil industry of the Gulf Coast of Texas and Louisiana. Spindletop, in 1901, with its enormous cap-rock production revealed the possibilities of the salt domes. The lateral sand development at Vinton, in 1910, renewed interest in the then known domes which were non-producing, or were producing from the cap rock or from sands above the cap rock. The discovery of three domes, Nash, Orchard and Long Point, in the year 1924, by means of the torsion balance and the seismograph, is the beginning of intensive explorations of the Gulf coastal plain by geophysical methods. Domes other than those mentioned have no doubt been found during the last few months of the year but tests have not been drilled to confirm the evidence of the instruments. DISCOVERY OF DOMES BY GEOPHYSICAL METHODS The Rycade Oil Corpn. operated the first torsion balance on the Gulf Coast in October, 1922, and the Roxana Petroleum Corpn. brought in one of these instruments and began work in December, 1922. The U. S. Coast and Geodetic Survey made some gravity observations at Damon Mound, in 1923, with a pendulum apparatus. In March, 1924, the Marland Oil Co. placed the first seismograph on the Gulf Coast and the Gulf Production Co. followed with one in May. In June, 1924, the Gulf Production Co. began operations with a torsion balance. The Atlantic Oil Producing Co., The Texas Co., and others have experimented with several types of instruments involving various principles. During the next few years, a great advance in geophysical methods may be expected, especially if one of the newly discovered domes should be productive. The first dome discovered was the Nash, in Fort Bend County, Tex., about 6 mi. east of Damon Mound. A slight elevation and two shallow wells containing sulfurous waters made the locality somewhat interesting from the standpoint of surface indications, and the torsion-balance measurements indicated the presence of a dome. On July 20, 1924, the Rycade Oil Corpn. No. 1 Wisdom encountered lime at a depth of 634 ft. and anhydrite at 639 ft. The hole was abandoned on Sept. 8, 1924, at 769 ft. in anhydrite. A cavity in the anhydrite caused much delay and the final abandonment of this test.

Jan 3, 1925

By Ralph C. Flow

In Cleveland County, North Carolina, 1 ½ miles south of Kings Mountain, Foote Mineral Co. operates an open pit for the production of spodumene, feldspar, mica and commercial stone. Spodumene concentrate is sent to Foote Mineral's Sunbright, Va., plant and to other customers. Exton, Pa. and New Johnsonville, Tenn., plants produce lithium com- pounds sold to the oil industry for multipurpose lithium-base greases, to the metal industry as welding flux, to the air conditioning market and to the glass industry. Ceramic-grade spodumene, feldspar, and mica concentrates go to other processing companies from the Kings Mountain plant. Waste amphibolite is delivered to a neighboring quarry operation. Geology and exploration of the deposit have been described by T. L. Kesler, Chief Geologist of Foote Mineral Co., in the September 1961 MINING ENGINEERING. Measured ore reserves as published at that time were 20.7 million tons. The ore deposit consists of a series of lithium-bearing pegmatites enclosed in amphibolite and mica schist wall rocks. The general strike of the pegmatites is northerly, and in the southern part of the pit, they dip slightly towards the west. The largest body being mined has a fairly uniform thickness of about 200 ft. Other pegmatites in the pit area range from 20 to 100 ft in thickness. Minerals in the pegmatites are 20% spodumene, 32% quartz, 6% muscovite, 41 % feldspar and 1 % trace minerals.

Jan 10, 1962

By W. M. Baldwin, C. R. Johns

Cobalt is reported1,2 to scale in accordance with the Pilling and Bed-worth3 parabolic law: where w = weight increase per unit surface area K = constant l = time The reported values of the parabolic oxidation constant, K, in the temperature range 600 to 1100°C follow an Arrhenius type of equation as inspection of Fig 1 shows. According to Valensi's theory5 on the scaling of metals where multiple-layered scales (for example, MeX, MeX2, and others) are possible, this fact could be construed as indicating that a single oxide only is formed on cobalt in this temperature range. Since the single straight line extends above 920°C where only CoO is stable in air (see Fig 2) it might be inferred that this is the only oxide formed on scaling. Arkharov and Voroshilova10 have studied the scales formed when cobalt is heated in air in the temperature range 385 to 800°C and report that CoO is indeed found in the scale but that CoO4 is also found as an overlay and in increasing amounts in the lower temperature ranges. No quantitative data regarding the relative proportions of the two oxides were reported. Again in the light of Valensi's theory this would indicate that the straight line in Fig 1 would be expected to undergo an inflection at some point in the temperature range 385 to 800°C. Chauvenet2 has studied the oxidation rates of CoO to Co3O4 and has found this reaction to proceed parabolically with time but reports parabolic scaling rates which are considerably (about ten times) larger than the scaling rates of cobalt metal itself. This is difficult to explain in terms of Valensi's theory although a full discussion of the possible discrepancy cannot be made in view of the lack of sufficient data. These points made an investigation of the scaling behavior of cobalt in air an attractive study. Discussion of Results Relatively large (approximately 95 sq cm of surface area) samples of 0.020 in. thick electrolytic cobalt strip,* sanded with 2/0 paper, were heated in air in a cyclone type furnace. The samples were weighed before and after the scaling treatment. The weight increases so observed obeyed the Pilling and Bedworth parabolic law at all temperatures studied. The parabolic scaling constants when plotted on a logarithmic scale as a function of absolute temperature are reproduced

Jan 1, 1950

By J. Pinto, F. Galasso

THE current emphasis in preparing boron fibers by reduction of gaseous boron compounds on a resistively heated metal wire substrate has renewed interest in the borides of those metals which have relatively high melting points and are available as fine wires. A knowledge of the structures and properties of the borides, which are formed when boron diffuses into the metal core during boron deposition, can be of assistance in the understanding of the boron fiber formation process and the fiber properties. Many of these borides are well-known and their properties have been measured. However, when an unidentified boride is found in the core, it may be difficult to establish its composition because of the small amount of material available, the preferred orientation effects on the reflections in its X-ray pattern, and the possible overlap of X-ray reflections if several borides are present in the core. For example. the proper indexing of the X-ray pattern of WB4, which was formed in the tungsten substrate core during boron fiber formation, was accomplished only after small single crystals of this boride were grown and X-ray precession investigations were conducted.' This note presents the results of a study of the phases formed in the core when tungsten, tantalum, and molybdenum metal wires were used as substrates in the boron fiber preparation process with particular emphasis on the identification and characterization of a higher boride of molybdenum analogous to WB,. Boron was deposited on resistively heated stationary 0.0012-in.-diam tantalum, tungsten, and molybdenum wires at 1050°C for various times up to 60 sec using boron trichloride and hydrogen as the reactant gases. After 60 sec of boron deposition the fibers were approximately 0.006 in. in diam. Examination of photomicrographs of fiber cross sections showed that the boron had diffused nearly to the center of the tungsten and molybdenum cores in 15 and 30 sec, respectively, and only halfway to the center of the tantalum core in 60 sec. X-ray diffraction photographs of the fibers indicated that it was also after 15 and 30 sec deposition times that the tungsten and molybdenum metal reflections, respectively, had disappeared from the X-ray patterns of the fibers. The patterns of the boron fibers produced using tantalum wire as a substrate showed that amorphous boron, TaB2, and tantalum metal were present after a few seconds deposition time and remained even after deposition times of 60 sec. Until a deposition time of 15 sec was reached, the tungsten substrate fibers contained amorphous boron,273 6WB, W2B5, and WB4 as well as tungsten metal, while the molybdenum substrate fibers contained amorphous boron, MoBa, Mo2B5, and molybdenum metal for deposition times up to 30 sec. Just before the molybdenum metal pattern disappeared, a pattern similar to that of WB, appeared, suggesting that a phase, MOB,, isomorphous with WB,, was present in the fiber. This same pattern was obtained from the product formed by heating a mixture of molybdenum metal and excess boron powder in a boron nitride crucible at 1960°C in an argon atmosphere. As was the case with the WBn pattern, this pattern could best be indexed on the basis of a hexagonal unit cell rather than the tetragonal unit cell Chrktien and Helgorsky reported for ~0~4,~ see Table I. The unit cell parameters for MoB4 were calculated to be a, = 5.214A, co = 6.358A. Assuming the space group P63/mmc and positions5 2M01 in 2b and 2MoII in 2c found for tungsten in WB~,' a logical structure for MOB, was determined using geometrical considerations to place the boron

Jan 1, 1969

By W. P. Frey

The briquet plant of the Lehigh Coal and Navigation Co., at Lansford, Pa., has previously been referred to.' It has passed the stage of experiment and now rests on a foundation practically and financially sound. The purpose of this' paper is to explain how success has been attained, and to set standards for the development of hard-coal briquetting which may eliminate future failures. All the conclusions are based on actual results, avoiding speculation and theory. Up to three years ago, the L. C. & N. Co. used coal-tar pitch as a binder in making hard-coal briquets. The plant operated with a monthly output of 300 to 600 tons and was unable to meet its own expenses. Naturally, no one was satisfied, especially as the ideals of a smokeless briquet were still unrealized. Then came the Dutch oil process, introduced in this country by the General Briquetting Co. of New York. This process uses as binder a small percentage of heavy residue of petroleum, which, being liquid, permits great economy of handling; it also did away with the most objectionable fumes of the former briquets. This oil2 is not absolutely smokeless; heating the fresh fuel to red heat liberates some low-volatile hydrocarbons, yielding a white smoke which is not objectionable. On the other hand, this oil adds to the briquet about 7 per cent. of volatile matter, giving the product a heating capacity equal to that of the best free-burning anthracite coal. The average silt used in the manufacture of these boulets averages 16.5 per cent. chemical ash, corresponding to 12,000 B.t.u. per pound of coal. The Hydrolene used as binder runs about 17,500 B.t.u. per pound, and approximately 7 per cent. of it enters into the mixture, hence 12,000 X 0.93..........................11,160 B.t.n. 17,500 X 0.07.......................... 1,125 B.t.u. Total.....................................12,385 B.t.u. per pound of briquets

Jan 1, 1918

By R. L. Schmidt, J. D. Verhoeven

The diffusion coefficients and electrotralzsport mobilities of aluminum, gallium, and arsenic have been determined in molten germanium with the capillary reservoir technique. The diffusion coefficients are slightly higher than those determined by the solidification technique of Brirton et a1.1 It was found that aluminium and gallium migrate to the cathode in molten germanium) whereas arsenic migrates to the anode under an electric field. A possible technique for producing p-n junctions by means of electric field freezing is discussed in view of the experimental data. In the past decade or so the literature has abounded with articles concerning the solid-state properties of the semiconducting elements germanium and silicon. It is surprising by comparison how little has been published concerning the liquid-state properties of these materials. In the production of doped germanium or silicon the diffusion coefficient of the dopant in liquid germanium or silicon is an important quantity. Yet, to the best of our knowledge, no one has ever made a direct measurement of the diffusion coefficient of solutes in either molten germanium or silicon. A number of authors'-4 have determined some diffusion coefficients by the indirect technique developed by Burton et al.1 This technique appears to give numbers of the correct order of magnitude but it does depend upon a number of assumptions in the analysis and also requires prior knowledge of the viscosity of the melt. In the present work a more direct measure of the diffusion coefficients of arsenic, gallium: and aluminum in molten germanium has been made. It has been shown independently by two groups of authors5, 6 that, when an electric current is passed through the interface of a solidifying metal containing an impurity, the resulting electrotransport in the liquid boundary layer at the interface offers a mechanism for control over the redistribution of the impurity accompanying the solidification. These authors show that the degree of control is proportional to the mobility, U of the impurity atoms in the liquid boundary layer, where the mobility is defined as the drift velocity relative to the solvent per unit electric field. In principle the results apply to the solidification of a doped semiconductor and offer an interesting technique for control of the doping of a semiconductor. In the present work the mobilities of aluminum, gallium, and arsenic were determined in molten germanium in order to evaluate the potential usefulness of electro-transport as a technique for solute control when applied to the solidification of doped germanium. EXPERIMENTAL PROCEDURE Both the diffusion coefficients and the mobilities were measured using high-purity alumina capillaries and a resistivity technique for analysis. A schematic diagram of the electrotransport apparatus is shown in Fig. 1 and the details of the cell design are shown in Fig. 2. For the mobility experiments electrical contact with the bottom of the capillary was made with graphite, as shown in Fig. 2. In order to prevent electrical contact with the melt the graphite was coated with a thin layer of alumina using a plasma spray torch. The cell assembly, a graphite electrode, and another assembly containing two blank capillaries were fastened to the lavite disk shown in Fig. 1. To make a run the system was evacuated and the doped germanium was outgassed at the operating temperature of 1030°C. The cell and blank capillaries were then submerged beneath the melt and a slightly positive pressure of helium was introduced to fill them. After passing current through the cell for a given time the cell and blank capillaries were raised from the melt and the furnace was shut off. The temperature of the cells dropped below the freezing point of germanium within 1 to 2 min after the furnace was shut off.

Jan 1, 1968

By L. S. Richardson, N. J. Grant

Iodide-grade titanium, two oxygen alloys, and two aluminum alloys were studied by means of creep-rupture tests from 1000° to 2000°F. From the test information an evaluation was made of, 1) the relative creep-rupture strengths of the u (hexagonal-close-packed) and 0 (body-centered-cubic) forms of titanium and some of its alloys; 2) the effects of solid-solution strengthening by oxygen and aluminum on the u and 0 structures; and 3) the extent and effect of atmospheric oxygen alloying on rupture life in tests above about 1000°F. THE use of titanium alloys at temperatures above 1000° F has been considered unlikely by most investigators because of low creep strength (based on a requirement for room-temperature ductility, formability, and weldability) and low oxidation resistance. The results of this testing program do not entirely uphold this pessimism in terms of strength and oxidation resistance. The observations described below are based entirely on stress-rupture results, although some creep tests were also carried out on these alloys. Three items of primary importance are covered: 1) Stress-rupture data in the form of the Larson-Miller parameter curves for several titanium alloys at temperatures up to 2000°F; 2) The relative strengths of the hexagonal-close-packed a structure and the body-centered-cubic 0 structure; 3) The effects of solid-solution alloying on the creep-rupture properties of titaniu'm at elevated temperatures. Only two investigatons have reported the creep- rupture properties of titanium at temperatures above 1000° F. Lunsford and rant' tested iodide titanium; their values are also utilized in the paper. EXPERIMENTAL PROCEDURE After a few tests had been made in a conventional creep-rupture test machine, it became clear that some sort of atmospheric protection would be necessary for short-time tests conducted at temperatures above 1600°F, or for times greater than 100 hr at 1200°F or above. Several furnace units and test machines were constructed, the most successful of which is shown in Fig. 1. Certain experimental difficulties peculiar to titanium were encountered; for example, the use of molybdenum holders was dictated because titanium forms low melting-point eutectics with conventional high-temperature alloys containing appreciable amounts of iron, nickel, or cobalt. This same difficulty made the use of chrome l-alumel thermocouples in direct contact with a test specimen impossible, above about 1500" F. The high-temperature high-vacuum furnace shown in Fig. 1 was capable of maintaining a vacuum of better than 10"5 mm of mercury at 2000°F (pressure measured in cold part of system) and 5 X lo-' mm at room temperature. Most of the tests eonducted in vacuum were at temperatures

Jan 1, 1960

By W. D. Ludemann, J. E. Dor, L. A. Shepard

Recovery of the creep resistance of 99.99 pct pure Al was studied at temperatures 540°, 573°, 600°, and 611°K. Poly-crystalline specimens crept under a stress of 950 psi to a strain of 5.5 pct were allowed to recover for periods of from 1 min to 16 days under a residual stress of 4.4 psi. Increased creep rates upon reapplication of the 950 psi stress evidenced softening of the material. The activation energy for the recovery process was found to be 64,000 cal-per mol. THREE major observations have clearly revealed that the creep of polycrystalline aluminum above about 510°K is controlled by the rate of climb of jogged edge components of dislocations past the barriers impeding their motion: 1) Extensive polygonization, characteristic of climb, takes place during creep.'9' 2) The activation energy for creep equals the estimated activation for self-diffusion. 3) The stress law for creep coincides with theoretical predictions based on the climb mechanism.4,5 The decreasing rate during the primary stage of creep must be ascribed to the introduction of additional barriers to the glide of dislocations. During secondary creep the density of barriers must remain constant, the rate at which new barriers are formed being equal to the rate at which they recover. For this reason the nature of the barriers, and their rates of formation and recovery, are significant to a complete understanding of creep. It is proposed here to study the kinetics of the recovery of barriers to creep of high-purity polycrystalline aluminum in the climb range. The technique will consist of creeping a series of tensile specimens under a prescribed stress to given state following which the specimens will be recovered for various times and temperatures under approximately zero stress. The amount of recovery will be determined by comparing creep curves following the recovery. EXPERIMENTAL PROCEDURE The material used for this investigation was a 99.99 pct pure Al supplied by the Aluminum Co. of America in sheets of 0.001-in. thickness having an H-18 temper. The spectroscopic analysis of impurities gave Cu-0.004 wt pct, Fe-0.002 pct, Si-0.001 pct, others-0.000 pct. Creep specimens were machined with their tensile axes in the rolling direction of the sheets. Annealing in a molten potassium nitrate-potassium nitrite bath for 1 hr at 686K, followed by air-cooling, resulted in a grain diameter of from 0.22 to 0.27 mm. Creep machines were equipped with constant stress lever arms of the type suggested by Fullman, Carreker, and Fishher,' which maintained the applied stress to within 0.04 pct of the reported value of 950 psi. Creep strains were calculated from extensions over a 6-in. gage section to the nearest 3 X 10"5. The temperatures of testing, 540°, 573", 600°, and 611°K, were obtained by immersing the specimen and extensometer assembly in a molten KNO2-KNO3 bath. Temperatures during the periods of creeping could be maintained constant to within better than ± 1°K. Correlation of creep data at different temperatures of testing demanded the use of an appropriate temperature-compensated time 8. Previous investigations have shown that the creep of pure metals at temperatures above about 0.55 of their melting temperatures can be correlated by the functional relationship3" e=f(0), s= const. [1] where e = total plastic strain during creep f = a function that depends on stress a = stress 6 = te-Q/RT = a temperature-compensated time t = time under test Q = 35,500 cal per mol = activation energy for creep R = gas constant, and T = absolute temperature In the present series of tests all of the creep was conducted under the same stress of 950 psi. To provide identical initial conditions for the recovery all specimens were first crept to a temperature-compensated time of = 47 X 10-14 min which resulted in a creep strain of 0.055 + 0.005 regardless of the creep temperature. During recovery, a small stress (4.4 psi) was permitted to remain upon the specimens to maintain tautness in the pulling assembly and to prevent mechanical damage to the soft specimen. After each recovery period, the full stress was reapplied and

Jan 1, 1961

By Arthur F. Taggart

The quality of aggregate materials is. of major importance in governing durability and permanence of concrete structures. The problem of selecting suitable aggregate materials is two-fold. Geological factors include the type and character of the aggregate source, presence of known or suspected reactive constituents, and presence of thermally incompatible materials. Laboratory investigations include petrographic studies, soundness and reactivity tests, and tests of thermal properties. The importance of each factor in the selection of satisfactory aggregate material is considered in detail.

Jan 1, 1950

By H. I. Young

Inasmuch as there has been a great deal of activity in this district recently, a paper of this kind should treat of all the various phases of mining, namely, prospecting, developing, and operating. Prospecting .. Where ore is found at a depth of 100 ft. (30 m.) or more, the prospect work is done by churn drilling. Several makes of churn drills are used in this work, both steam- and gasoline-driven machines being used. The drilling is usually started with a 6-in. bit, and the size of the bit is reduced, if necessary, as the hole is advanced. It is general practice to drill from 100- to 400-ft. holes, but this is governed entirely by the location and formation of the ground. In drilling sheet ground, close spacing of drill holes is unnecessary, but in narrow orebodies, the holes are spaced from 15 to 50 ft. (4.6 to 15 m.) apart. Ten years ago, very few assays were kept of the drilling, but during recent years records have been kept very accurately, showing the location, elevation, assays, and also the vertical section of the hole. After the orebody is reached, cuttings are taken every 2 or 3 ft. (0.6 to 0.9 m.) samples being sometimes taken by pouring the water off the cuttings and taking a portion of the coarse material for assay. It has been found, however, that very often the sludge material poured off with the water contains high mineral values. To overcome this, cuttings from each 2 or 3 ft. are put in a container, and, after the water is evaporated, sample for assay is taken by means of Jones samplers. Permanent records of cuttings showing various formations are kept in glass jars or glued on large cards. Drilling at present is costing from $1.25 to $1.50 per foot. In pre-war times, the drilling costs ran from 75c. to $1 per foot. Development After proving property by drilling, shafts are put down to the ore-body. These are usually vertical shafts, either single or double compart-

Jan 1, 1918

By AIME AIME

ALMOST as many attended the annual dinner this year as last, when the presence of Mr. Hoover was such an attraction that almost two-thirds more than had ever attended before were present. Only by putting the late comers at tables in the balcony could everybody be accommodated. Past President De-Golyer was the toastmaster and in opening the post-prandial exercises referred to the regrettable fact that this was the last of the long series of dinners which have been held at the Waldorf, as the hotel will be torn down to give way to an office building before another year. To the delight of the gathering "Oscar" appeared and, in a delightfully brief but characteristic speech, referred to the long association that had existed and hinted that a new Waldorf-Astoria may arise, where the Institute could continue to gather annually in an enlarged replica of the room they had met in so long. Before taking up the presentation of the medals, Mr. DeGolyer referred to the Institute's "Legion of Honor," the 34 men who have been members continuously for over fifty years. For various reasons only five of them, W. S. Ayres, F. G. Corning, Henry D. Hibbard, A. F. Schneider and Arthur Thacher, could be present. They were all seated at the speaker's table, and W. S. Ayres, 56 years a member, as the dean of the group, was called on to respond for them all. He said: "The introduction I have just received would indicate that this particular group of men to which I belong is considered by the chairman to be a group of real antiques. Possibly you are questioning the accuracy of his judgment. I hope you are, although there may be some first-sight evidences tending to substantiate the view held by the chairman.

Jan 1, 1929

By Charles Legrand

The power plant of the Burro Mountain Copper Co. is located near Tyrone, N. M., at 5,950 ft, elevation. It is interesting because it uses the largest stationary Diesel engines in the United States. The general layout of the plant is shown in Figs. 1 and 2. The building is of steel-frame construction with hollow-tile walls and corrugated-iron roof; the floor is concrete and all windows have steel frames, making a fireproof building. The building is made to accommodate one more electric generator unit, which is being installed; also two 4,000-cu. ft. air compressors direct-connected to three-cylinder engines with the same size cylinders as the electric units. The power plant consists of two 815-kva., 60-cycle, three-phase, 6,600-volt, 180-r.p.m. generators, direct-connected to five-cylinder, two-cycle Diesel engines; the necessary circulating pumps for cooling water, cooling towers and oil storage tanks. A portion of the power is used in the same building as the generating units to run one of two 200-kw. rotary converters delivering 260-volt direct current, and a 2,500-cu. ft. air compressor, delivering air at 95 1b.-pressure, direct-connected to a 400-hp., 6,600-volt, three-phase synchronous motor. The remainder of the power is used to run a 1,500-ton concentrating mill 3 1/2 miles from the power house, various hoists, pumps and motors about the mines and the lighting and water-works of the town of Tyrone. The direct current is used for electric traction in the mine, also to run hoists and motors that were installed before the new power plant was built. Due to the large hoists that take starting peaks of 250 kw. and the 10-ton electric locomotive that takes at times 150 kw., the load is extremely variable, as shown in Fig. 3. The two five-cylinder vertical Diesel engines, which are rated at 1,250 b.hp. at sea level, have cylinders of 525-mm. diameter (20.6 in.) and

Jan 1, 1917

R. B. BRINSMADE, Puebla, Puebla, Mexico (communication to the Secretary*) :-As I have previously considered the general equations for mine-valuation,1 I will here discuss only that part of Mr. Finlay's paper criticized by E. E. White, along with some of the general principles of mining taxation, under the following six topics: 1. Rate of interest earned by sinking-fund. 2. Rate of interest earned by investment. 3. Place of royalty item in valuation. 4. Place of taxation item in valuation. 5. Calculation of future ore-prices. 6. Valuation of undeveloped mining land. 1. Rate of Interest Earned by Sinking-Fund.-Mr. Denny's quoted opinion of a 3 per cent. rate is evidently based on English conditions before the Boer war. The great destruction of liquid capital by the great wars and catastrophes since 1897, along with the flood of gold and consequent rise in the average index of commodity prices, has undoubtedly increased the rate of interest at least one-half per cent. In the United States sound savings banks now allow 4 per cent. on deposits, while safe bonds are quoted at prices which yield even 5 per cent.. 2. Rate of interest Earned by Investment.-Gold-mines with uncertain and scanty ore reserves, the objects of Mr. Denny's quoted remarks, are quite different from iron,. copper, or coal mines with definite mineral reserves blocked out ahead by drilling or driving. While 10 per cent is often all inadequate yield from gold-mines, the latter class of mines are often, as safe as city real estate and resemble it as an investment in more ways than one.

Jan 10, 1913

By Stephen Krickovic

THERE is today no proven continuous mining machine that can be used under all the varying conditions found in most bituminous coal mines. During the last five years, however, both the machines and methods of using them have been improved. Coal operators can now exercise a fair degree of selectivity, except those who must struggle with thick and hard partings and operate in seams less than 40 in. thick. It must be realized, then, that more than one type of continuous miner may be used advantageously in the same coal mine. Although this appears to violate the standardization generally sought after, the gain can more than offset added maintenance and, to a lesser degree, operating problems. It is equally important to realize that most coal mines will require one or more conventional loader setups in the plan of total mechanization. Seam variations, adverse physical conditions, and special designs of main headings for haulage and ventilation, to name only three reasons, may render 100 pct use of continuous miners uneconomical. Of course, this situation may change. In one mine, prior to 1954, machines that ripped coal from the face achieved only average results, as compared to the impressive performance of boring-type units in another coal mine. A boring-type unit was therefore selected for the first mine in the belief that the chance of success would be greater if it were used in a combined cutting and wedging operation, cutting a full face in its forward movement. The miner was located in a part of the mine where a special projection could be readily developed, a solid area scheduled for mining according to the overall progress plan. All openings surrounding the particular area were carefully investigated for the presence of sulfur balls. Fig. 1 (opposite) shows the representative seam section, containing the several pyritic bands 1/4 to 1/2 in. thick; a characteristic Pittsburgh seam parting averaging 5 to 6 in. of slate, coal, and slate; and the occasional py-rite lenses 2 to 3 in. thick. Under normal conventional mining methods, the top 10 or 12 in. and the bottom 4 in. are left in place to offer roof protection

Jan 1, 1958

By G. Wranglen

On account of the possibility of isolating carbides in steel it is generally assumed that the electrode potential of iron carbide is more noble than that of ferrite.1,2,3,4,5 Differences from 0.032 V1 to 0.4 V4 have been recorded. However, it is important to realize that the more noble behavior of cementite in relation to ferrite is not an issue of thermodynamics but of reaction kinetics. Theoretically, cementite is less noble than ferrite, which is a direct consequence of its thermo-dynamic instability. With the value ?F°298 = +4700 cal per mol for the free energy of formation of cementite6 it is easily calculated that the electrode

Jan 1, 1950

By J. Murray Riddell, George A. Morrison

This paper is a companion to the one by George A. Morrison on Mining a Deep Limestone Mine in Ohio.‡ Barberton is 8 miles west of Akron, Ohio, and 23 miles south of Cleveland. The underground mining of limestone at Bar-berton constitutes the world's deepest limestone mine. The stratigraphy is as follows: 0-20 ft. Loam, clay, sand and gravel. Water bearing. 2-40 ft. Fractured sandstone. Water bearing. 40-110 ft. Sandstone with interbedded shale, slightly fractured. Water bearing. 110-314 ft. Sandstone with interbedded shale, slightly fractured. Water carrying. 314-2197 ft. Shale with occasional seams of sandstone, which varies in thickness from a few inches to 4 feet. Dry. 2197-2247 ft. Limestone. Dry. 2247-2742 ft. Dolomitic limestone. Dry. 2742-2767 ft. Salt. Dry. 2767- Dolomitic limestone. Dry. All of the strata dip to the southeast, about 0.5 per cent from the horizontal. The top 110 ft. of the crust is water-bearing. The rock strata are naturally fractured to a depth of 314 ft., sufficient to allow the passage of water. In the shaft-sinking operations, a stra- turn of oil-bearing sandstone one foot thick was encountered at a depth of 520 ft., and flows of methane gas were pierced at depths of 1350 and 1952 feet. Specifications for the mine plant called for, in part, the sinking of two vertical shafts and a hoisting plant capable of producing at the rate of 300 tons per hour. No. I shaft is 550 ft. west of No. 2 shaft. Each shaft measures 8 by 17 ft. outside of steel. General features of the design (Fig. I) are: Principal set members, 6-in. H-section; connecting angles (studdles), ? by 4 by 4-in. angle irons; spacing of sets. 8 ft. centers; spacing of bearer sets, generally, 160 ft.; bearers, of 12-in. I-beams. Each bearing set featured a concrete ring about the periphery of the shaft, steel to rock, and 8 ft. in height; permanent guides, 6 by 10-in. long-leaf yellow pine, 85 per cent heart. The Shaft-sinking Operation The preliminary shaft-sinking work consisted of driving interlocked steel piling about the exterior of the shafts to depths of 35 and 32 ft., respectively, and of such horizontal dimensions as to ultimately permit the pouring of a concrete collar 2 ft. in horizontal thickness. Following the pouring of a shaft collar, a temporary wooden headframe for shaft-sinking purposes was erected. The head-frame, while ordinary, featured: (1) a storage pocket of 300 cu. ft, capacity with truck servicing facilities, and (2) pneu matically operated dump doors, which mere actuated by the hoistman, thus caring

Jan 1, 1946

THE CHAIRMAN (F. K. COPELAND,* Chicago, Ill.).-At this particular time conditions existing in this, country, and elsewhere, make all questions of milling or smelting or mining, or anything else, absolutely secondary to the one question of labor. We have always devoted our attention largely to the efficiency of machinery, and to reductions in costs, etc., and have let this tremendous problem of our relation to labor more or less take its own chances. There has never been a time when those who are responsible for the operation of business of different kinds were as com-pletely at a loss as they are now, so that anything that can be brought out that relates to labor is, to my mind, of utmost importance. T. T. READ, Washington, D. C.-This formulation of a method of curtailing forces at the Copper Queen is a notable step in advance of our treatment of personnel in the mining industry. So far as I know, it is the

Jan 12, 1919