Search Documents

By E. I. Alessandrini, A. U. Seybolt

Selective oxidation (preferential oxidation of a single alloy component) can be an important oxidation mode in the case of alloys such as Si-Fe, Al-Fe, and so on, when heat-treating in atmospheres of low oxygen potential. It was the purpose of this work to identify the oxide films formed on iron containing 31/4 pct Si at low oxygen potentials, and to make some observations on the H2O/H2 ratios required to form them. EXPERIMENTAL METHOD HYDROGEN of varying water content offers a very convenient method of establishing a wide range of oxidizing power, or oxygen potential. The method chosen to provide a desired H2O/H2 ratio was to nearly saturate hydrogen at room temperature by bubbling the gas through water at room temperature, and then to wring out the excess water by passing the wet gas through a long glass spiral immersed in a refrigerated liquid at a desired dew point. After oxidation, the samples were examined by electron diffraction in order to identify any film which might be present. PREPARATION AND TREATMENT OF SAMPLES The samples were prepared from a Si-Fe alloy made in the laboratory using electrolytic iron and 96 pct ferro-silico11, vacuum-induction melted, hot-rolled then cold-rolled to 0.015-in. thickness. After the cold-rolling the samples were annealed at 1000°C. Transmission Laue X-ray patterns showed very little evidence of preferred orientation, but it is likely that a weak texture could have escaped notice. The chemical analysis was as follows: 3.34 Si, 0.01 Al, 0.001 0, 0.006 C, 0.002 N. Before each sample was oxidized, it was polished through 4/0 emery paper, cleaned and dried using benzene, carbon tetrachloride, acetone, absolute alcohol, and ether. The method of oxidizing the samples was as follows: Samples about 1/2 by 1 by 0.015 in. were held in the upper, cool part of a vertical vacuum furnace until the desired temperature was established in the furnace, Fig. 1. The sample was then lowered into the uniform hot zone where it was heated quickly to the desired temperature, and subjected to hydrogen of controlled moisture content (dew point) as mentioned previously. Temperatures from 400" to 1000°C were used, and dew points from room temperature to —78°C were explored. In general, the runs lasted about 6 hr, but a few runs were of different duration, as will be indicated later. After the predetermined period of time had elapsed, the specimens were withdrawn by the hollow stainless steel-quartz holder to a cool zone at the top of the furnace. EXPERIMENTAL RESULTS The results are summarized in Table I. Most of the electron-diffraction patterns were obtained by glancing-angle reflection, but in a few cases it was possible to strip the oxide films from the surface by a total immersion in a 3 pct bromine-methanol solution. Some of the thinner stripped films yielded quite satisfactory transmission patterns. However, both diffraction techniques yielded the same results; the patterns while most frequently showing a (low) tridymite, also showed a (low) cristobalite in some cases. A few patterns showed evidence of both phases. Because of the known nonequilibrium behavior of silica, it is not surprising that both forms of silica could coexist on one sample. It was noted that at fairly low dew points such as —40°C, there was a tendency for diffuse diffraction rings, suggesting a very small crystallite size. Also some subsequent experiments to be reported later show that thin silica films can be amorphous.

Jan 1, 1959

By G. Y. Chin, W. L. Mammel

The problem of selection of the active slip systems for a crystal undergoing an arbitrary strain has been analyzed by Taylor and by Bishop and Hill. The Taylor analysis is based on a principle of' virtual work, and involves finding, among numerous cotnbinalions of slip systems that satisfy the imposed strain, the combination in which the sum of the glide shears is a minimum. Previously, Taylor has treated the case of axisymmetric flow when slip occurs on (111)(110) (or {110)(111)) systems only. His analysis has now been extended by computer methods to the cases of slip on {112}(111) and {123)(111) systerns and of mixed slip on {110), {1 12), and (123) planes with a common (111) slip direction, all of which are important in the deformation of bcc crystals. The results are computer-plotted as contours of the ratio of the floe strength to the critical resolved slzea-r stress for slip, for axial orientations distributed throughout the standard stereographic triangle. Implications of the computer results to texture develop,merit, texture hardening, and dislocation theories oj work hardening are discussed. WhEN a single crystal is extended in the usual tension test, the lateral dimensions can change relatively freely. In this case, the glide shear produced by slip on a single slip system is sufficient to accommodate the (tensile) deformation. Since slip is governed by a critical resolved shear stress law (the Schmid law'), the single active slip system is one for which the stress, resolved on the slip plane and in the slip direction, is the highest among the several equivalent slip systems. This amounts to saying that a value M = U/t = y/~ is a minimum among the equivalent systems, where M is the inverse of the familiar Schmid factor (a and E refer to tensile stress and strain, and T and y refer to resolved shear stress and shear strain). A grain embedded in a polycrystalline aggregate, on the other hand, cannot freely change its shape due to constraint from its neighbors. In this case, slip from five independent slip systems (to accommodate five independent strains) is generally required.' Based on the principle of virtual work and assuming that the critical resolved shear stress for slip is the same for all systems, Taylor hypothesized that, among all combinations of (five) slip systems which are capable of accommodating the imposed strain, the active combination is that one for which the sum of the absolute values of the glide shears is a minimum. Again, this is equivalent to saying that the value of M = CjlyjI/ is a minimum, in analogy to the single slip case. Taylor aminimum,analyzed the case of {111)(110) slip for fcc metals, and applied the analysis to crystals undergoing axisymmetric flow, that is, the same macroscopic shape change as the poly crystalline aggregate under uniaxial tension (or compression). For the twelve equivalent {111}( 110) slip systems, there are 384 independent combinations of selecting five systems to satisfy the five independent linear equations of imposed strain.4 Taylor calculated the value of M for each combination* and obtained the active com- *A number of the independent combinations were omitted from consideration in Taylor's original work (see Ref. 5). bination (minimum M) for a number of axial orientations distributed throughout the standard stereographic triangle. Later work by Bishop and Hill*'8 showed that Taylor's least-shear hypothesis was equivalent to a maximum work principle which they advanced. Using the simplified Bishop and Hill method for {111)(110) slip, Hosford and Backofen' obtained detailed contours of constant minimum M for the same axisymmetric flow case. In contrast to {111}(110) slip in fcc metals, slip in bcc metals is generally described as occurring on {ll~)(lll), {112)(111), {123) (111) systems as well as mixed slip composed of all three. Since the direction cosines of the slip plane normal and the slip direction enter as a product in the Taylor analysis, the Taylor solutions of ,M for {110)(111) slip are identical to those for { 111} 110) slip. The other three cases of slip, however, have not been solved. In view of the numerous combinations of slip systems involved in the calculations, the Taylor analysis is clearly oriented toward computerized solutions. THE TAYLOR ANALYSIS In order to obtain the active combination of (five) slip systems by solving for the minimum value of M = we first express the (small) strain components E,, with respect to the cubic axes 1, 2, 3 ([loo], [010], [001], respectively) of the crystal, in terms of the sum of the glide shears yj from slip systems j: where n, and n,j refer to direction cosines of the slip plane normal, and dri and dsi to direction cosines of the slip direction, of slip system j, all referred to the cubic axes. In practice, the strain components are given with respect to the specimen axes X, y, 2. These components are readily converted to ers through the tensor transformation where irk and 1,~ are the direction cosines between the two sets of coordinate axes.

Jan 1, 1968

By Y. A. Chang

Phase relationships in the system Cr-Si have been established based on the melting point, X-ray, metallo-graphic, and DTA studies. The three intermediate phases, Cr3Si, Cr5Si,, and CrSi,, melt congruently at 177V ± I@,Cr3Si, 1680"i 20°, and 1490" *20°C, respectively, while the fourth intermediate phase CrSi, melts peritectically at 1413" i 5°C to Cr5Si3 and a melt containing 51 at. pct Si. The temperatures and compositions of the four eutectic isotherms occurring in this system are given below: DTA and metallographic evidences indicate that Cr5Si, undergoes a phase transformation at 1505" i20°C. The high-temperature form of this phase could not be retained by the quenching techniques used in this study. TECHNOLOGICAL interest in the developing of composite systems, consisting of Sic on the one hand as a fiber-reinforced material and metallic substances such as chromium, nickel, or Cr-Ni alloys as a binding agent on the other hand, stimulated the present investigation of phase relationships in the binary system Cr-Si. Earlier works concerning this system have been evaluated and summarized by ansen and Anderko.' Their phase diagram was based mainly on the works of Kieffer, Benesovsky, and schroth2 and Kurnakov.~ According to these authors, the three intermediate phases Cr3Si, CrSi, and CrSi, all melt congruently at approximately 1730°, 1600°, and 1550°C. However, they did not agree on the compositional stability of the fourth intermediate phase between Cr3Si and CrSi. Later Parthe, Nowotny, and schmid4 determined the structure of this phase to be tetragonal T-1 type using the single-crystal method, and concluded that this phase had a formula of Cr5Si3. Since the compilation of Hansen and Anderko,' a new phase diagram for the system Cr-Si has been proposed by Elliott5 based on the works of Goldschmidt and rand,' Guseva and ~vechkin,~ and Trusova, Kuzev, and Ormont8 and the earlier works quoted by Hansen and Anderko.' According to this proposed phase diagram, all four intermediate phases have large ranges of homogeneity and all melt congruently. More recently, Svechnikov, Kocherzhinskii, and yupkog studied the system Cr-Si by the DTA-method. According to their findings, the three intermediate phases, Cr3Si, Cr5Si3, and CrSi,, melt congruently at 1700°, 1720°, and 1475"C, respectively, while the fourth intermediate phase, CrSi, melts peritectically at 1475°C to Cr5Si3 and a melt containing 50 at. pct Si. The temperatures and compositions of the four eutectic isotherms were found to be: In view of the discrepancies existing in the literature concerning the system Cr-Si, it was decided to rein-vestigate the phase relationships in this system. EXPERIMENTAL a) Starting Materials. Chromium disilicide and chromium or silicon powders were used in the present study to prepare the melting point and DTA samples. CrSi, was obtained by directly reacting cold-pressed elemental powders in an atmosphere of Hz at a temperature of about 1250°C. Chromium powder, purchased from Stark Chemical Co., had the following impurities in ppm: Fe, 200; Mg, 1000; and 0, 250; while silicon powder, purchased from the Welded Carbide Co., had the following impurities in ppm: Ca, 700; and Fe, 3500. b) Melting-Point Determination and Differential Thermal Analysis. Cylindrical melting-point samples of approximately 13 mm in diam and 30 mm in length with a rectangular groove in the center were prepared by hot-pressing of well-mixed powder mixtures in graphite dies. Before the melting-point determination, the hot-pressed samples were ground on a sand paper to remove any minute surface contamination of graphite. A small hole of 1 mm in diam, drilled on the center portion of the samples, served as a blackbody cavity for the temperature measurements. DTA samples approximately 13 mm in diam and 15 mm in length were prepared in a manner similar to the melting-point samples. Melting points were determined using the Pirani technique under a helium atmosphere of 40 psi. The design, performance, and operation of this apparatus have been described in detail by Rudy and ~ro~ulski.'~ The temperature measurements were carried out with a calibrated disappearing-filament-type micro-pyrometer. The measured temperature was corrected for losses from the quartz window of the melting-point furnace and for deviations from blackbody conditions of the observation hole. The procedure for temperature correction has also been previously described." The DTA method of Heetderks, Rudy and Eckertl' was also used to check any phase transformations of selected alloys in the system Cr-Si. It was not possible to make remated runs on the same sample once melt-

Jan 1, 1969

By F. R. Brotzen, D. L. Davidson

ALTHOUGH much effort has been devoted to the problem, the nature of plastic flow in bcc metals is still not fully understood. Some of the difficulties encountered stem from the scarcity of information on orientation effects and the uncertainty as to the glide system in these metals. In an attempt to provide some of this information, the present investigation was carried out, using zone-refined molybdenum single crystals deformed in tension and in direct shear. Considerable evidence exists to indicate that the primary slip system for molybdenum is (110) <111>.1,2 Figs. 1 and 2 indicate that this is, indeed, the case for direct shear at room temperature (see Ref. 3 for a description of the shear-testing equipment and procedure). Moreover, from Fig. 2, the shear stress on the (123) is lower than that on the (112). This would be the case if, as has been suggested,4,5 slip on these two planes is in reality com-

Jan 1, 1965

By J. D. Hunt, D. T. J. Hurle

A uariety of eutectic structures are formed in faceted/nonfaceted eutectics. The various structures are explained in terms of the absence or presence of small facets in the liquid groove. Regular structures are produced when, for purely geometric reasons facels cannot form. The presence of a facet in the liquid groove leads to the formation of an irregular or a cell-like complex regular structure, due to the relative immobility of the groove. A classification of eutectics was proposed by Hunt and jackson, based on the presence or absence of facets on the primary phases (the absence of facets may be predicted from the dimensionless entropy of melting2). Eutectics were divided into three groups: 1) eutectics in which both phases grow in a nonfaceted manner; 2) eutectics in which one phase grows faceted, the other nonfaceted; 3) eutectics in which both phases grow faceted. It was suggested that regular1 rodlike or lamellar structures1 should be formed in the first group, that irregular or complex regular structures1 should be formed in the&apos; second, and that irregular structures1 should be formed in the third. Recently it has been shown that the structural classification is incomplete. Regular rodlike structures (InSb-NiSb eutectic3), or broken lamellar structure (Bi-Zn eutectic, Fig. 8), are formed in alloys of the second group when the faceted phase has a large volume fraction. Hunt and jackson&apos; argued that regular structures could form in faceted/nonfaceted systems, but that such structures would be unstable in the presence of microfacets on the lamella of the faceting phase, because the growth rate at a point on such a facet would depend on the kinetic undercooling at the point of nu-cleation on the facet, and not on the local kinetic undercooling. In these circumstances it would not be possible to consistently balance the compositional and kinetic undercooling over a lamellar structure and thus obtain a stable isothermal interface. In this paper we discuss in detail the origin of the various structures formed in faceted/nonfaceted systems, pointing out that the most important factor promoting the formation of a regular structure is the absence of a facet in the liquid groove. 1) FACET FORMATION IN SINGLE-PHASE MATERIALS Facets form when there is an energy barrier for the addition of a new solid layer on an existing solid. When a barrier is present,2 growth proceeds by the lateral movement of steps across a crystallographic plane. The rate-controlling stage of the process occurs when the step is first formed. Hulme and Mullin6 have shown that faceting in single-phase materials can only occur when both interface curvatures are convex with respect to the solid and when the surface is tangential to the facet plane. When even one of the curvatures is concave a facet does not form because new layers of solid from adjacent regions can always feed the facet plane, Fig. 1. Growth under these conditions is then as easy as elsewhere. Similar considerations will apply to eutectic growth; consequently the shape of the faceted phase is extremely important. 2) LAMELLAR SPACING CHANGES IN EUTECTICS Jackson and Hunt7 have shown that the interface undercooling AT of a growing lamellar interface (neglecting kinetic undercooling) is related to the lamellar spacing, A, and growth velocity, v, by an expression of the form: where m, Ql, and nL are constants of the system given in Ref. 7. Eq. [I] is plotted for fixed v in Fig. 2. Jackson and Hunt postulate that a regular eutectic grows near, but to the right of the minimum in the AT vs A curve. They argue that the spacing cannot be to the left of the minimum because the interface is then unstable to fluctuations in A. It cannot grow too far to the right, because when the spacing becomes too wide an isothermal interface can no longer be maintained over the large-volume-fraction phase.7 It is argued that during any change in growth rate the lamellar spacing remains in the permitted range by the movement of lamellar faults. When the spacing is too wide, the fault, shown in Fig. 3, moves to the left; when the spacing is too narrow it moves to the right. The faults, however, have to be formed. heir formation has been shown to occur when local regions deviate considerably from the spacing defined by the lamellar When the spacing is locally too narrow (it passes to the left of the minimum, Fig. 2), pinching off of the narrow phase occurs. When the spacing is locally too wide, the interface on the large volume-fraction phase can no longer be maintained as an iso-

Jan 1, 1969

By CYRIL W., William Campbell, Henry M. Howe

THIS paper gives the results of an investigation of the behavior of the argentiferous cobalt-nickel arsenides of Temiskaming, Ontario, in roasting, made in the metallurgical laboratories of the School of Mines, of Columbia University in the City of New York. The ore was kindly given by the owners of the La Rose and Trethewey properties at Cobalt, Ontario, and Mr. E. J. Hall, Tutor in Assaying in Columbia University, has helped us much. I. OBJECT OF THE INVESTIGATION. The object of the investigation was to learn:- 1. The temperature at which the arsenic is most rapidly expelled; 2. The thoroughness with which it is expelled by prolonged roasting at this temperature; 3. The effect of adding charcoal (a) near the end of the roast and (b) at the beginning of the roast. II. NATURE OF THE ORE. The important ores mined in the Temiskaming deposits are native silver-with small amounts of dyscrasite (Ag6 Sb), argentite (Ag2S), pyrargyrite (Ag3SbS3)-smaltite (CoAs2), chloanthite (NiAs2) and niccolite (NiAs). Mispickel (FeAsS) and cobaltite (CoAsS) also occur in smaller quantities. The average composition of the ore shipped from this district for the first six months of 1905 -was: silver, from 4.1 to 4.8 per cent.; cobalt, from 6.9 to 8.2 per cent ; nickel, from 3 to 4.7 per cent ; and arsenic, from 30.9 to 34.6 per cent. The ore which we treated consists chiefly of smaltite ; In our laboratory-work

Jan 1, 1907

RECENTLY seven Boy Scouts were chosen from all the troops in the United States for their all-around ability, excellence in&apos; scouting, and special ability as writers. Two of the members of this selected group were sons of In-stitute members. In the accompanying illustration, Ber-nard Queneau, son of A. L. J. Queneau, of the U. S. Steel. Corp., can be seen at the extreme left, just behind Theo-dore Roosevelt, who is shaking hands with the boy next to. Carl Zapffe (standing in the middle with his hands behind him), the son of Carl Zapffe, manager of the iron ore prop-erties of the Northern Pacific Railroad.

Jan 6, 1928

By Don L. Kendall, Martin G. Buehler

A simple physical model has been developed to fit carrier-removal data in silicon irradiated near room temperature with reactor spectrum neutrons. Commonly observed donor and acceptor defect energy levels are assumed to be introduced linearly with neutron fluence. The donor levels (in ev) are Ev + 0.16, Ev + 0.27, and Ev + 0.31 and the acceptor levels are Ec - 0.55, Ec - 0.40, and Ec - 0.1 7, where Ev and Ec are the valence and conduction band energies, respectively. The introduction rates of each level are adjusted to fit literature initial carrier-removal rate data. When normalized with respect to the Ev +0.27 level, the relative values of introduction rates are 5.3, 1.0, 3.1, 1.0, 2.0, and 20.0, respectively for the six levels indicated above. To fit p-f (hole concentration vs neutron fluence) and n-f (electron concentration us neutron fluence) data, the introduction rates are multiplied by a factor which preserves the relative values given above. This factor depends upon irradiation temperature, reactor energy spectrum, neutron fluence calibration, and oxygen content of silicon. An extensive study of the effect of neutrons on carrier-removal in silicon irradiated with reactor spectrum neutrons (E > 10 kev) has been given by Stein and Gereth1 (SG) and Curtis, Bass, and Germano&apos; (CBG). They measured initial carrier-removal rates for both p- and n-type silicon over an impurity range typical of silicon devices. In this work, we attempt to fit a simple theory to this data to establish a usable relationship between hole and electron concentration, p and n, respectively, and neutron fluence f. The p-f and n-f relations are needed to assist in the design of neutron tolerant silicon devices and are needed to clarify presently used empirical resistivity-fluence relationships.3 Neutron damage in silicon produces a variety of defects ranging from simple point defects to defect clusters. For the purpose of this treatment, we assume that simple point defects dominate carrier-removal effects. In contrast to this view, stein4 has proposed that defect clusters are responsible for a significant portion of carrier-removal effects. In the following section, it is shown that the carrier-removal effect in n-type silicon with an electron concentration less than 1015 cm-3 can be explained adequately by assuming that the divacancy is the dominant defect and that its introduction rate is independent of the electron concentration. For electron concentrations greater than 1015 cm-= an additional acceptor defect center is needed, and for simplicity the A-center (vacancy-oxygen pair) has been chosen. Although the E-center (vacancy-phosphorus pair) can account for some of the results, the A-center was chosen because the E-center requires a more involved treatment which the presently available data do not justify. In p-type silicon three radiation-induced donor levels are assumed, namely the divacancy and two other centers of unspecified nature located at Ev + 0.16 ev and Ev to 0.31 ev. The donor divacancy at Ev + 0.27 ev is assumed to be introduced at the same rate in p-type as in n-type. However, this rate is too low to fit p-type initial carrier-removal data. The dominant centers in p-type silicon are assumed to be the Ev + 0.16 ev and Ev + 0.31 ev levels where the latter is not the divacancy. The introduction rates are chosen to fit initial carrier-removal rate data. Assuming that the introduction rates are independent of Fermi level, the ratio between them is fixed for subsequent p-f and n-f calculations. Using the same ratios, the initial carrier-removal rate data1,2 as well as p-f and n-f data1,5 can be fit provided the absolute value of the introduction rates are adjusted to account for irradiation temperature, reactor energy spectrum, neutron fluence calculation, and the oxygen content of silicon. THEORETICAL ANALYSIS This analysis is basically the same as that used by Hi116 to analyze electron damage in silicon except we express the degree to which an impurity level is ionized not in terms of the Fermi level, but in terms of carrier concentration. Landis and pearson7 have used the latter approach to analyze y-damage in silicon. Neutron-induced defects responsible for carrier-removal at room temperature are assumed to be simple point defects with no interaction between defects so that they may be represented by discrete energy levels. It is also assumed that no constituent of a defect complex is used up and defects stabilize shortly after irradiation. Defects are assumed to be introduced linearly with fluence according to the product Rtf where Rt is the defect introduction rate and f the neutron fluence. Taking into account the ionization of defects according to Fermi statistics, and considering charge neutrality where minority carriers are neglected, the n-f relation is where no is the preirradiation electron concentration. The parameter Nt is the electron concentration at which the ionized defect concentration is one-half the total defect concentration (Rtf) or where Et is the defect energy level. For silicon at 300°K, ni = 1.45 X 1010 cm-3 and Ei = Ev+ 0.542 ev which was determined using Ec — Ev = 1.11 ev and me* = 1.07 mo and mh* = 0.558m0. The spin degeneracy factor, which usually appears as a number multiplying the Nt/n term of Eq. [1], is taken as unity. In effect, this factor has been incorporated into the defect en-

Jan 1, 1970

By Arthur Taggart

THE following conclusions on the work of the Hardinge mill are based on data furnished to the writer by the Hardinge Conical Mill Co. in the form of the mesh cards hereto appended. Energy units (E. U.) and relative mechanical efficiencies (R. M. E.) are computed by the "volume method" of Stadler.1 Screen apertures used are the average apertures of testing screens of the meshes given. Card 122. June 28, 1912. Vipond Porcupine Mines Co., Ltd., Schumacher, Ont., Canada. Ore from mill bin. Gangue, quartz and basalt. 4.5 ft. by 13 in. ball mill. Capacity, 48 tons per 24 hr. Charge, 4,000 lb. balls. Speed, 33 rev. per minute. Horsepower, 15 to 17. Water, 100 per cent. by weight. (50 per cent. ?) Product deslimed and oversize reground-in pebble mill, see Card 113. Feed to mill through 2-in. mesh.

Jan 7, 1915

By L. Mair

A STUDY by J. R. Low, Jr.1 on the effect of quench aging on the Charpy-impact specimens of semikilled 1020 steel disclosed that a decrease in cooling rate from 1275°F raised the transition temperature. This was demonstrated in his investigation by controlling the cooling rate of impact specimens to duplicate that of a heavier plate and com- paring the properties with air-cooled specimens and quenched specimens. The transition temperature of the samples that had been cooled at a rate estimated to be similar to that of an air-cooled 3/4 in. plate was approximately 45ºF higher than the quenched samples. The transition temperature of the air-cooled series was between that of the slow-cooled and the quenched series. On the basis of this work, it appeared that the cooling rate of plates after rolling in a hot mill would have a bearing on the brittle fracture of the

Jan 1, 1955

By Allan D. Taylor

INTRODUCTION From the designer&apos;s view, the installation starts with the first definition of the orebody, and progresses through a long and complex development. The design is affected not only by the characteristics of the ore, but by all of the personalities and events of the project during its development. The following discussion attempts to touch on the most important aspects which define the context in which the designer must work in apply the do&apos;s and don&apos;ts. That context is the basis of the viewpoint. WHAT CAN GO WRONG The Project Is Going Over Budget This is a common and serious concern to the plant designer. The Project Falls Behind Schedule Another common and disturbing condition with which the plant designer must cope. Some Equipment Fails to Perform This can be due to either faulty equipment or operating deficiencies. It can be the result of a wide variety of causes, but the designer will be an interested party in the search for the cause and the cure. The Plant Isn&apos;t Flexible Enough Sometimes a plant will handle some or even most of the ore satisfactorily but is unable to treat another type properly. This can be a significant problem. An example might be a case where low capacity of a cyclone feed pump makes it impossible to accompany an increase in grinding mill throughput with a corresponding increase in dilution water. This could lead to an increase in cyclone feed density, and a loss in product grade or a limit on the plant capacity. Spillage And Cleanup Are Excessive This is one of the most common and annoying defects in metallurgical plants, and one for which the designer can rarely delegate blame. Maintenance Is Excessive Another common complaint in new plants, and also one for which the dedesigner must accept most of the responsibility.

Jan 1, 1982

By Franklin G. Pardee

IN 1920 the Minnesota Tax Commission estimated a reserve of 1,341,674,538 long tons of iron ore in Minnesota, the Michigan State Tax Commission report showed 199,092,855 long tons in reserve in that state, and the Wisconsin Geological Survey set the Wisconsin reserves at 21,500,000 long tons. The total reserve that year for the Lake Superior District amounted to 1,562,267,393 long tons. Ten years later the reserves of iron ore in these same districts were Minnesota 1,235,227,510, Michigan 168,349,823, and Wisconsin 23,000,000, or a total of 1,426,577,333 long tons. The decrease in ore reserves in this ten-year period was 135,690,060 long tons, but the shipments were 520,746,975 long tons. In other words, the ten-year depletion in reserves was only 8.68 per cent. If similar conditions carry into the future this calculation would indicate a life for the ore reserves of the Lake Superior region of over 100 years.

Jan 1, 1933

By J. J. Calaman, D. H. Fleming

DURING 1950 the jet-piercing process was used commercially in the piercing of primary blast-holes in magnetic taconite at the preliminary taconite plant of .the Erie Mining Co., Aurora, Minn. The Erie Mining Co. purchased a jet-piercing machine and associated equipment in 1949, and the machine has been in operation since its installation in the summer of that year. An overall view of the pit with the JPM-1 jet-piercing machine in operation is shown in Fig. 1. During three months of 1949 and continuously since February 1950, production piercing took place under all pit conditions. By the end of October 1950, a total of 15,000 linear ft of hole had been pierced in an open pit handling an average of 1200 to 1800 tons of crude a day in one 8-hr shift. While it is recognized that this output does not approach the millions of tons a year planned for the developing Minnesota taconite projects, the machine as a unit has been operating under conditions probably more adverse than those that eventually will be encountered in the large operations. This pilot operation has permitted evaluation of the piercing problem in the full-scale taconite plant. This paper describes jet-piercing process funda- mentals, important features of the latest jet-piercing burners and machine, actual piercing results obtained, and new developments that give promise of materially increasing overall process efficiency. To produce the blasthole, jet-piercing utilizes thermal energy, as contrasted with the application of mechanical energy in churn drills and jackham-mers. The heart of the process may be termed a tailored flame produced by a rocket-type burner, thermodynamically similar in every respect to that of the giant rockets being developed for military purposes. The heat release in the combustion chamber of the burner is about 50x10&apos; Btu per cu ft per hr as compared with 5x10&apos; for most modern steam generators.* Combustion of liquid petroleum fuels (kerosine, diesel oil, or No. 2 fuel oil) with gaseous oxygen in the burner chamber at pressures of 100 to 200 psi results in temperatures of about 4300°F. Expansion of the hot combustion gases through divergent nozzles produces high-temperature supersonic jets having measured velocities of about 6000 fps. Impinging the flame jets on rock causes a thin surface layer to expand and break away from the base as a result of the thermally induced stresses. This spalling action is aided further in chert and quartzite by the 0.82 pct volume change resulting from the 6 to p quartz inversion at 1066"F.t The dynamic action of the jets whisks the spalled rock

Jan 1, 1952

By PHILIP N. MOORE

IT is a pleasure to realize even at that day the dignity of the engineer&apos;s calling was upheld. May I also add my firm belief that today there be many engineers who will qualify to the specifications of our interesting author. Since that time, the development of the world has been chiefly due to the engineer, and so far as human brain can foresee, the material tasks of the future will continue to follow the directions of his judgment. Popular opinion says this is the age of the engineer; literature, which in the long run, voices public sentiment, shows it in the number of engineers who figure as characters of fiction. The engineer has been doing the big things necessary to increase the comfort and efficiency of mankind, but while a certain amount of fame and repute falls to him, too often he figures as the hired man of the entrepreneur, using that term not in the offensive sense of a mere promoter, but to mean the great visioned master of enterprise who has seen ahead of other men, recognized the coming needs of the world, and through ability to inspire others and to hire capital for his use has also been able to hire engineers as needed. Justly enough, therefore, to such men comes the fame as well as the prize of the game.

Jan 1, 1926

By Barry D. Lichter, Pierre Sommelet

High-temperature heat contents of InSb, GaSb, and AlSb were measured over the temperature range 400" to 1450°K using a diphenyl ether drop calorimeter. Smoothed ualues of the thermal properties, H$ - H:9s, have been derived and are tabulated at even temperature intervals. The heats of fusion of the three compounds were determined as, respectively, 5707 *100, 7780 * 100, and 9800 5 3011 cal per g-atorn at the determined melting points of 797" l°, 985" * , and 1330" * 5°K. The calculated entropies of fusion are, respectively, 7.16 0.12, 7.90 * 0.11, and 7.37 * 0.23 cal per deg per g-atotn. The heat capacities increase substantially on tnelting in contrast to the behauior of structurally related germanium and silicon. Deriations from the Kopp-Neumann rule are negative for solid compounds and positive for the liquid phases. Previously obsevrrd "post melting" in InSb is confirmed. The high-temperature thermal properties of 111-V compounds are presently not well-established, despite the technical importance of these semiconducting cbmpounds. Uncertainties in available heats of fusion and heat contents have seriously hampered thermo-chemical evaluations&apos; and thermodynamic analyses of phase equilibria2"" in these systems. This paper reports results of high-temperature heat content investigations of InSb, GaSb, and AlSb measured in the range 400" to 1450°K employing a diphenyl ether drop calorimeter. Similar measurements for InAs and GaAs will be reported in a following publication.~ EXPERIMENTAL PROCEDURES Samples. High-purity samples of the compounds InSb and GaSb were supplied in the form of crushed crystal fragments by Dr. Carl Thurmond of the Bell Telephone Laboratories and in the form of single crystals by Dr. A. Strauss of the M.I.T. Lincoln Laboratory. Single-crystal samples of semiconductor-grade AlSb were supplied by Dr. W. P. Allred of the Bell and Howell Research Center. Chemical analyses indicated that all compounds were stoichiometric to *0.1 at. pct, which is within the experimental uncertainties of the analyses. Samples were crushed, weighed, and encapsulated in evacuated, thin-walled, fused silica capsules. The capsules were nearly identical in external shape, 2 cm by 2 cm diam, but varied in weight due to differences in wall thickness. One sample of AlSb was contained in a thin-walled, high-purity alumina cup encapsulated in silica and used for heat content determinations of liquid AlSb. The capsule materials showed no visual evidence of reaction with any of the compounds. The sample and capsule weights are given in Table I. Calorimeter. A Bunsen-type calorimeter, similar in design to a previously described instrument6 but employing diphenyl ether (C6H5)&apos;0 as the calorimetric substance, was used for measurements of heat contents above 300.0°K, the melting point of diphenyl ether. Heat input to the calorimeter caused isothermal melting of diphenyl ether, and the resulting increase in volume was measured by displacement of mercury from the calorimeter into a 200 cm horizontal, calibrated capillary, 1.25 * 0.01 mm diam, or into a weighed beaker. The advantages of diphenyl ether over water have been previously pointed out7 and include: i) an increase by a factor of 3.5 in sensitivity as measured by the ratio of the volume change to the enthalpy change on fusion, ii) the smaller required extrapolation from the melting point to the standard temperature of 298.17"K, and iii) the positive volume change on fusion of diphenyl ether in contrast to the contraction which occurs on fusion of ice. Diphenyl ether was purified by fractional crystallization to 99.95 mol pct as determined from the melting point depression with fraction crystallized. During assembly of the calorimeter, the ether was repeatedly outgassed under high vacuum to remove dissolved air. The calorimeter receiving vessel consisted of an 8-in.-long by 1:-in.-diam copper tube with twelve horizontal 3-in.-diam radiator "fins" for dissipating heat to the surrounding mantle of diphenyl ether. Before forming the mantle the chamber surrounding the receiving vessel contained 3300 cu cm of liquid diphenyl ether above 250 cu cm of mercury which was

Jan 1, 1970

By A. J. Williams

THE province of Saskatchewan, situated in the center of the Great Plains region of Canada, has, like most prairie areas, an essentially agricultural economy. Most of its population of about 860,000 is located in the southern half of the province in the farming and ranching areas. To the north of the prairie is a broad forested belt supporting a considerable timbering industry, and the northern one third of the province is glaciated pre-Cambrian rock formation. This latter area is, relatively barren of vegetation, but the presence within it of a considerable variety of radioactive, noble and base metals, and industrial minerals has been shown by prospecting in recent years.1 Glacial Geology The Keewatin ice sheet, considered to have accumulated in the country to the west of Hudson Bay in Pleistocene time, covered at its maximum advancement almost all of Saskatchewan and extended south of the international boundary. Only in the Cypress Hills in the southwest and around Wood Mountain in the south central portion of the province did the preglacial formations escape the action for this glacial period. The bedrock of the plains and forest areas therefore is overlain by moraines and modified glacial drift, which vary in thickness from a few feet to 400 or 500 ft.2 Glacial action in the pre-Cambrian area of the province was largely erosional, most of the more recent formations and some of the pre-Cambrian rock being transported out of the area to the south and west. It has been estimated that about 13 pct of this area is composed of lakes and rivers not too adaptable to rail or water transportation, so that until the use of aviation for exploration purposes became general; development of the area was slow. To the south, the heavy. mantle of glacial drift has to some extent deterred the discovery of industrial minerals in the bedrock underlying the forest and prairie regions.3 At the same time, this drift contains numerous deposits of those most elementary and necessary industrial minerals, sand and gravel. Sedimentary Basin The major feature of the sedimentary deposits underlying the plains regions is the basinal structure known as the Moose Jaw syncline, which runs from the southeast corner of the province in a northwesterly direction. To the west. of this syncline the formations curve upward, then have been faulted and further upthrust to appear at the surface in the foothills of-the Rockies in Alberta; to the east and north they curve upward into Manitoba and northern Saskatchewan, but the surface contacts are covered mostly with glacial drift.2,3 The axis of the syncline dips to thee southeast, so that there is also an upward trend of the formations along the axis to the northwest. In illustration of the regional structure underlying the province, the pre-Cambrian basement has been logged in drillholes at the following depths in several locations: Ogema (south central), 9390 ft; Gronlid (northeast), 2599 ft; Vera (northwest), 4422 ft; Big River (north northwest), 2348 ft. Fig. 1 indicates the general surface geology of the province, ignoring such glacial overburden as may overlie many of the bedrock formations. Also indicated is the approximate location of the axis of the Moose Jaw syncline.4 Industrial Minerals Clays: The province is fortunate in possessing a widespread distribution of clays of ceramic value, ranging from those used for heavy structural products to the high grade pottery and china clays. Shales suitable for brick and tile production are found in the Upper Cretaceous and Tertiary formations across the south of the province where the glacial drift is thin or nonexistent. Many deposits of glacial lake clays suitable for such wares are found scattered over the rest of the province south of the pre-Cambrian area. The Whitemud formation of the Upper Cretaceous is a narrow sedimentary, band of secondary clays found intermittently, at points, across the, south of the province where glacial action did not disturb or remove them.8 In the southwest corner of the province, around Eastend in the Frenchman River valley, the refractory clays of this formation are contaminated somewhat with iron compounds or other alteration products of basaltic rocks. This eliminates the use of those clays in true whitewares, as they fire to creamy buff shades at the lower temperatures and to a blue-specked grey at cone 8 to 12, (2280°F to. 2390°F), the range commonly used in firing whiteware. However, for use in the production of colored artware, caneware, stoneware or crockery, and sewerpipe, this type of clay makes an excellent body that requires little or no addition of flint, feldspar, or other fluxing materials such as are required in the higher class of ware.9 It is not a grade of clay that can be shipped great distances to the manufacturing centers, but a market for considerable tonnages has developed at nearby Medicine Hat, where cheap natural gas is available for the firing of the ware. Farther east in the south central portion of the province, the clays of the Whitemud formation are generally more refractory and white burning. The formation is divided into three zones, consisting of white clays, brown shale, and white sandy clays.

Jan 1, 1952

By B. T., Colley

AS always when metallurgical operations are conducted within or close to agricultural and stock-raising regions, the question of damage due to fume and smoke presented itself when the Cerro de Pasco Copper Corporation&apos;s new smelter commenced to operate in La Oroya in 1922, For more than twenty years the Corporation had operated its old plant close to Cerro de Pasco without encountering difficulties from smoke claims, owing to the fact that it was in an open plain where more or less constant air currents carried and dissipated the smoke over large areas, affording ample dilution. But Oroya is in a deep canyon formed by four contributing valleys up and down which the smoke travels for long distances in a more or less concentrated form. Though the altitude of Oroya is more than 12,000 ft., and the surrounding country rises to much greater elevations, nevertheless there exists there a large and important stock-raising industry and also a considerable development in agriculture, consisting of the cultivation of potatoes, barley, etc.

Jan 1, 1945

By L. D. Jaffe, H. C. Mann, E. L. Reed

The authors have recently published1 evidence that brittle transgranular fracture of polycrystalline metals does not originate at a point and propagate continuously across the material, but rather develops at numerous related points, leading to a series of micro-cracks which subsequently link up. Series of related microcracks were observed in steel specimens broken in fatigue—specifically, at the central portions which broke during the final sudden fracture. Microcracks of the type mentioned have also been reported by Baeyertz, Craig and Bumps&apos;2 in steel broken under impact. % Some micrographs published by Irwin3 may possibly be interpreted as showing discontinuous brittle cracks. This paper presents additional observations of the authors on discontinuous crack propagation under various conditions. Impact Test Specimens The impact test specimens were cut longitudinally from a steel forging containing: The heat treatment consisted of oil quenching in a heavy section from 1600°F and tempering at 1260°F. The resulting yield strength was 78,000 psi, tensile strength 100,000 psi, elongation 20.0 pet in 2 in., and reduction of area 55.0 pet. Standard V-notch Charpy specimens were broken in a 217 ft-lb machine at a striking velocity of 16.8 fps. Energy absorption and fracture appearance of this material in the V-notch Charpy test are plotted as functions of temperature in Fig 1. After test, fractured halves of specimens appearing 0, 40, 80, and 100 pet fibrous (to the unaided eye) were electroplated with nickel, sectioned longitudinally (perpendicular to the notch at its midpoint), polished and etched with Cohen-Hurlich-Jacobson (C-H-J) reagent (picric acid plus Zephiran chloride in ethyl ether)4 or with Vilella reagent (1 pet picric plus 5 pct hydrochloric acid in ethyl alcohol).5 Fig 2 and 3 show cracks near the path of final fracture in the specimen rated 0 pct fibrous. Many of the cracks terminate at the boundaries of ferrite grains, some at boundaries of pre- existing austenite gzains. * A crack often starts near the end of another. Cracks within the same ferrite grains are parallel or approximately parallel in several cases. A large percentage of the cracks are branched. Fig 4 illustrated a group of cracks in the 40 pct fibrous specimen. Branching and parallelism are well marked. No more than three directions of crack have been observed on the polished surface in one ferrite grain. This is consistent with the evidence6 that brittle fracture of ferrite takes place on the cube face crystallographic planes: the {100} planes. The appearance of some cracks suggests that they have passed around a projecting corner of a second ferrite grain by going outside the plane of polish. In Fig 5 cracks in the 80 pet fibrous specimen may be observed. Some of

Jan 1, 1950

THE strike and dip of bedded formations is readily determined by trigonometry if some marker horizon is intercepted by three holes. If no marker can be identified and if orientation of the cores is unknown, as is the usual case in diamond drilling, the determination still can be made readily by the use of a stereonet if the bearing, inclination, and angle the bedding makes with the core axis is known for each of the three holes. Such determination, valid only if the bedding orientation is fairly uniform within the area drilled, is considered simpler, faster, and more effective than any solution previously published. Method: The steps of this procedure are as follows: 1) Mark north and south poles on tracing paper placed over stereonet.* 2) Plot the three diamond drillholes by drawing a line from the center of the net in the direction of the bearings of the holes. Then rotate the paper until each line, in turn, lies along the equatorial diameter of the net; the end of each line is determined by the inclination of the hole measured in degrees from the periphery toward the center of the net along the equatorial diameter. Fig. 1 illustrates a vertical hole and a hole inclined at —23" due east. 3) With the projection of one diamond drillhole along the equatorial diameter, measure from the end of the hole, to the east and then to the west, a dis- tance in degrees equal to the core axis-bedding plane angle. Find two more points by measuring the same number of degrees north then south along the great circle from the end of the drillhole. Draw a circle, the center somewhere along the direction of the projection of the drillhole, to connect these four points. Draw circles for the other two diamond drillholes in the same manner. See Fig. 1 for two circles representing core axis-bedding plane angles of 35" and 23" and Fig. 2 for these plus a third circle representing a core axis-bedding angle of 42" in a hole bearing S 50 W inclined at —52". 4) Rotate the tracing paper until one great circle on the stereonet is found which is tangent to all three of the circles or parts of circles derived in the previous step. Trace this great circle on the paper and join its ends with a straight line passing through the center of the net. The bearing of this line is the strike of the bedding. In Fig. 2 the bedding strikes N 77 E. 5) Rotate the paper until the strike is along the polar diameter of the net. The dip of the bedding is determined by measuring along the equatorial diameter the distance in degrees from the periphery of the net to the great circle derived in step 4. The dip of plane illustrated in Fig. 2 is 55" to the N 13 W. Fig. 3 indicates the solution for three holes whose bearings and inclinations are N 20 W and —43o, due E and —30°, S 30 W and 23" with core axis-bedding angles of 30°, 50°, and 43" respectively. The bedding (stippled area) strikes N 44 W and dips 70" to the southwest.

Jan 1, 1956

By Harold E. Thomas, Samuel S. M. Chan, Nicholas Bada

The U.S. Bureau of Mines has developed a technique for locating and evaluating bedding plane cracks in mine roof by an air-injection and hot-film flow logging technique. It is ultrasensitive to cracks and is especially useful for detecting the early stage of crack development. Potential applications include: (1) correlation with roof sag measurements, (2) locating cracks for grouting, (3) comparison of mechanical and resin roof bolt effectiveness, and (4) possible delineation of the fracture zone to confirm the arch hypothesis. The required equipment is inexpensive and simple to operate.

Jan 1, 1975