Search Documents

By G. Derge, W. Peifer, J. H. Richards

INTRODUCTION A WIDE variety of metallurgical defects in steel have commonly been attributed to the presence of excessive amounts of hydrogen. These defects include flakes in rails and forgings, cracks in welds, and blisters in enameled ware. They have been related to hydrogen largely by circumstantial evidence because the proper sampling and analysis of steel for hydrogen has been known to be difficult and because no general agreement has existed with regard to the relative suitability and accuracy of available methods. The need for a direct approach to these problems has been widely recognized. This general situation has been well described in the publications of the British Committee on the Heterogeneity of Steel Ingots,1 and current approaches to the problem were reviewed in a recent symposium of the AIME.12 The plans described by the present authors at that meeting have now matured satisfactorily and will form the basis of this paper. The principle object of this paper will be to describe the methods of sampling and analysis which have been developed and to illustrate the usefulness and limitations of these methods by citing their application to a specific problem. The first problem selected for investigation was the behavior of hydrogen in rail steel. This was chosen because the occurrence of shatter cracks in rails has received a great deal of study over a long period of time. The defect can be controlled by the expensive procedure of slow cooling. However, it may be hoped that a better understanding of the factors influencing the hydrogen content of rails will lead to a more efficient control of this problem. Rails provide a good starting point for a more general study of hydrogen in steel because they provide a cross section large enough to develop cracks, yet small enough for convenient handling and sampling. Rails were also selected because they are made from plain carbon steel and it was felt that the initial work should not be complicated by the effects introduced by alloying elements. The considerations which determined the original planning of this study should be reviewed. The inherently complex nature of most hydrogen problems requires that a large amount of data must be collected for any particular case. This in turn means that any analytical procedure should be as rapid and simple as possible. The same objective of speed is indicated by the fact that it may finally become desirable to use hydrogen analysis in process control. It is also known that hydrogen is highly fugitive and that any procedure which facilitates early analysis of the sample without prolonged or irregular storage has distinct advantages. The most important previously reported methods of analysis may be classified into three general groups: (I) Vacuum fusion. (2) Vacuum extraction (without melting). (3) Total combustion.

Jan 1, 1948

By M. W. BERNEWITZ

DURING my recent extended visit to Australia and New Zealand, these notes on oil and gas prospecting in that part of the world were compiled from recent reports-press and government, from conversation with one of the financial leaders in the search for oil, and from personal observation of operations of the principal importers, blenders, and distributors of oil products; also from the astonishing testimony given by them to the Petrol Commission. Australia and New Zealand have practically no petroleum production beyond a few thousand gallons a year from wells in the latter Dominion. Everything is imported, Table 1. showing the quantities for 1929-30 in Australia and for 1930 in New Zealand,

Jan 1, 1934

By Clinton M. Young

The experiments herein described were carried on in 1908-9 by- the State Geological Survey of Kansas. Some months before taking up work on black powder the Survey had resumed work on an interrupted investigation of explosions in coalmines, a subject which is engaging the attention of numerous investigators. An unusual number of serious disasters has directed to the subject a study which discloses the disquieting fact that, in the United States, the ratio of lives lost per ton of coal mined has been 011 the increase. Methods of coal-mining have changed to some extent with the great increase of output, attained in comparatively recent years. These changes involve the working of very extensive mines, with increased difficulty of ventilation, increased accumulation of coal-dust, and a very great increase in the amount of explosive used. This last point assumes truly startling proportions when it is carefully observed. In the fields of the Middle West it is not now uncommon for a miner to use six kegs (150 lb.) of black powder in a " pay" of two weeks, while within the memory of men still active, one keg (25 Ib.) would last two men for a " pay." So great has the use of explosives become in some fields that the skilled coal-miner is hard to find, and the coal is not mined, but blasted. A preliminary study of the subject of explosions in coalmines has led to the belief that the use of large quantities of explosives, in some cases by slightly-trained men, had riot been

Jan 1, 1911

W. H. SHOCKLEY, Chairman, FRANK H.-PROBERT, :Vice-Chairman, T. A. RICKARD, Sec.-Treas.; 420 Market St.,. San Francisco, Cal. C. C. BRAYTON, J. F. NEWSOM. A Meeting of the San Francisco Section was held on May 7, 1917. Chairman Shockley was in the Chair. The Section was honored by the presence of President Moore and Secretary Stoughton of the Institute. C. W. Merrill introduced President Moore, who then spoke to the Section on the Aims of the Institute. He discussed the possibility of improving the standards of membership by introducing a classification of membership. The present rigid investigation of applicants was pointed out by him. He spoke of the important influence that the local Sections can exert on the Institute and of the importance of sociability and informality at the meetings. Secretary Stoughton, who was introduced by the Chairman, emphasized somewhat the same points. He mentioned the need for making the Bulletin of the Institute more, interesting than it is at present, this to be accomplished by raising the necessary funds by increased advertising. He asked for an expression of opinion on this point. He. said that the employment department of the Institute is now used extensively. At the request of Mrs. Mark L. Requa, Mr. Stoughton. announced that a San Francisco branch of the Woman's Auxiliary of the, Institute was being formed and asked that the ladies of the members' families send in their names to Mrs. Requa or to the Secretary of the Institute.

Jan 10, 1917

By Hugh S. Spence

IN the winter of 1941-42, muscovite mica was discovered by a young prospector, Justin Purdy, in the township of Mattawan, Nipissing District, Ontario, a few miles north of the small settlement of Eau Claire, which lies on the main Transcontinental Highway (No. 17) between Mattawa and North Bay. Muscovite had been known for many years to occur in the general Mattawa region, and various small efforts at production had previously been made by individuals working scattered deposits in the area. These minor activities, however, had never led to production of any consequence or the discovery of any important mica bodies. The Purdy finds were made in a heavily timbered, mountainous area lying about three miles north of the low-lying settled land along the highway, and in a section not hitherto prospected. The mica taken by Purdy and two partners from surface outcrops proved so remarkable in point of size of trimmed sheets that the find attracted considerable attention, and the area surrounding the three claims taken up by the prospectors was quickly blanket-staked by various interests. Though a number of other mica-bearing pegmatite dikes were 'found later on these stakings, none proved as rich as those on the original Purdy ground; very little commercial mica was obtained from them and attempts to develop them were short-lived. Purdy and his partners sold their initial production to dealers in Ottawa and Hull, where the Canadian mica industry long has centered. Young Purdy, unfortunately was killed in a motor accident in the early summer of 1942. His father continued mining operations for a few months and produced and sold a considerable amount of mica. In October 1942 the Purdy holdings were acquired by Inspiration Mining and Development Co. of Amos, Quebec, which had been active in staking in the area. This company formed a subsidiary, Purdy Mica Mines, Limited, to develop the property. Under the energetic management of Joseph R. Norrie, rapid progress was made, and production soon attained important proportions. Realizing from the outset the unusual character and potential value in the war effort of the Purdy discovery, the Metals Controller, Department of Munitions and Supply, at once arranged with the Department of Mines and Resources for an official geological report on the area, and also drew the attention of the War Production Board in Washington to what seemed likely to prove a highly important source of strategic-quality mica. Officials of WPB were sent up in the summer of 1942 to inspect the property,

Jan 1, 1947

By JOHN R. SUMAN

OVERWHELMING proof of the importance of oil in a modern national economy is afforded by the present European War. Treat¬ies and national boundaries have been cynically violated to secure greater supplies of the precious fuel. Petroleum substitutes have been desperately, and far from successfully, sought. The whole German military theory of the drang nach Osten, the drive to the East, is directed at cutting the British supply of oil and securing a supply for Germany. This is a war of machines, and the machines of war feed hungrily on oil. In view of this fact, it is surely comforting to know that we are living today in a nation which has surpassed all the rest of the world not merely in unearthing the raw supplies of petroleum which lie beneath its surface but also in every phase of the industry in mining, refining, processing, production, and distribution.

Jan 1, 1941

By G. A. Reinhardt, Albert Sauveur

Although many metallurgists know that some pearlitic special steels can be made troostitic, martensitic, and even austenitic, without quenching, and, therefore, without exposing them to the dangers of the quenching-bath, the practical significance of such possibility does not seem to have received the attention it deserves. Let us recall briefly the mechanism of the transformation alluded to. In Fig. 1 (after Guillet) is shown the constitutional diagram of nickel-steel; that is, of alloys of iron, carbon, and nickel. Any steel the composition of which falls within the area LPO is pearlitic after slow cooling; any steel the composition of which is represented by a point within the area MLO is martensitic, and any steel within the area MNO is austenitic. Starting with pearlitic steel, then by increasing the carbon-content or the nickel-content, or both, the metal becomes marten-sitic and eventually austenitic; that is, its composition crosses first the boundary-line LO and then the line MO—and it remains martensitic or austenitic after slow (air) cooling.' We have in this way imparted to the metal without quenching it the properties of hardened carbon-steel. In other words, the steel is now self-hardening; Nickel cannot be introduced into solid steel, but by the well-known process of case-hardening it

Jan 1, 1913

By H. Stuart, L. Zwell, N. Ridley

specimen that was subjected to 700°C for 250 hr is shown in Fig. 2(c). The precipitates in this foil appear round and exhibit only very faint strain contrast. From this evidence, along with that described above for the symmetry of the strain field, it may be concluded that this coherent precipitate is spherical, which is generally the favored shape for coherent precipitates when the lattice parameter mismatch is small.12 These observations are consistent with the assumption that this precipitate is the y' (Ni3Al, Ti) phase. y' is known to be spherical in the early stages of precipitation. It is fcc and is similar in composition to the matrix and thus would have contrast similar to that of the matrix as do these precipitates. Direct identification of the spherical precipitate did not prove possible because of its low volume fraction and small size. The results of this investigation suggest that the increases in yield strength and the decreases in elongation observed in 45-Fe 30-Ni 20-Cr alloys containing about 0.4 pct A1 and 0.4 pct Ti on prolonged aging at 550" to 700°C are very likely due to the presence of a coherent, spherical precipitate, thought to be y'. Mi-crohardness measurements indicated that the precipitation of semicoherent M23C6 resulted in some matrix hardening. However, this precipitation process occurs much more rapidly than the changes in mechanical properties at these temperatures. 1C. L. Clark, J. J. B. Rutherford, A. B. Wilder, and M. A. Cordovi: J. Eng. Power, 1962, vol. 84, p. 258. 2 F. A. Comprelli and U. E. Wolff: USAEC Report GEAP-4745, General Electric Company November, 1964. 3C. N. Spalaris: A Monograph, USAEC Report GEAP-4633, General Electric Company, July, 1964. THERE have been many X-ray investigations of the room temperature lattice parameters of austenite which has been retained in quenched steels of various carbon contents. The results of these investigations have been collected by Wrazej,1 Wever et al.,2 and by Roberts3 and are included in Fig. 1 due to Pearson.4 The dashed line in Fig. 1 was considered by Roberts3 to most reliably describe the variation with carbon content of the lattice parameter of retained austenite. This line is given by the equation: a (Å) = 3.555 + 0.044 wt % C and recent unpublished measurements by one of the authors (LZ) support this relationship. The object of this communication is to draw attention to a relationship which describes the variation of the room temperature lattice parameter of 'equilibrium' austenite with carbon content, and which is different from that for retained austenite. The relationship a(Å) = 3.573 + 0.033 wt % C has been obtained from lattice parameter measurements made on equilibrium Fe-C austenites at elevated temperatures, which have been extrapolated to room temperature. The room temperature lattice parameter of 3.555Å which the Roberts' relationship gives for pure y-Fe is no: in agreement with the value of 3.573Å obtained when the high temperature lattice parameter data of Basinski et aL.5 and of Goldschmidt6 is extrapolated to room temperature. A linear extrapolation was

Jan 1, 1970

By Thomas T., Read

T HE preceding chapter has recorded the initiation of mineral industry education during the period 1890-1910 in numerous institutions that had not previously offered it. It should also be emphasized that in many institutions where instruction had begun before 1890, as recorded in earlier chapters, but had not yet become firmly established,, this period was one of marked growth and development. This was not universally true, however, for at the Universities of Pennsylvania, Michigan, Illinois, Wisconsin, Washington (St. Louis), Iowa, Vanderbilt and Tennessee, and at the Polytechnic College of Pennsylvania, mineral industry instruction was being dropped during this period, instead of gaining in strength. It is necessary to emphasize this, because writers on the subject have not infrequently , attempted to make a much too simple correlation between mineral -discovery or production and the intensity of student interest in mineral industry curricula. It would naturally be true that periods of large mineral production would, in general, coincide with cycles of business prosperity, and the latter are conducive to starting new ventures, educational as well as business. It should be equally evident that opportunities for business and professional success might, in such periods, appear to increase at a more rapid rate in industries other than mineral, or in the utilization of minerals rather than in their production. The author has not been able to perceive any simple and clear relation between interest in mineral industry education and mineral discovery, production, and utilization, or general business prosperity. On the contrary, the more the problem is studied the more complex the factors involved in it appear to be. In a later chapter an attempt will be made to analyze them in more detail.

Jan 1, 1941

By E. F. Thomas

THE late George S. Rice was active in the inves--I- tigation of bumps, particularly in the last ten years of his career as chief mining engineer of the U. S. Bureau of Mines. Since most of his investigation was carried out in Great Britain, continental Europe, and—to a lesser extent—Canada, his thinking on prevention was influenced considerably by the experience of those countries. It is not surprising, therefore, that when he was called upon a few years before his retirement to investigate bumps in the U. S. and suggest ways to prevent them, he turned to longwall mining. A longwall method had been most successful in combating the bump hazard in mining coal under deep cover, especially in Great Britain, but the prevailing method there at the time was advancing longwall mining, which he knew was uneconomical under U. S. mining conditions. For this reason he proposed a modified retreating longwall system that he believed included the best features of the advancing method. As brought out by Rice,' if the cover is 2000 ft and 50 pct of the coal is extracted, the static load on the remaining pillars will be about 4000 psi, which exceeds the ultimate crushing strength in most instances. If the pillar coal is overloaded before a pillar line is established, then the abutment zone preceding a line of extraction is no place to split pillars or extract them by any method other than an open-end system. Rice therefore advocated open-end mining, preferably by longwall, but he was willing to compromise with long-face mining if the longwall method was not acceptable. Rice's system was put into operation in a mine in Harlan County, Kentucky,3 but subsequent experience has shown that it did not take into account two important factors—avoidance of pillar-line points and maintenance of adequate development in advance of the pillar-line abutment area. For ten years after Rice's retirement the USBM did little investigation and research on bumps, chiefly because so few were occurring that there was not much cause for alarm. But in 1951 there were three occurrences involving fatal injuries, and the Bureau began a statistical survey in that year. C. T. Holland, head of the department of mines at Virginia Polytechnic Institute, was retained as a consultant. The resulting study' of 117 case histories brought out these important conclusions: 1) Almost invariably the bump occurred in a locality affected by the abutment zones of one or more pillar lines. 2) In most cases the locality of the bump was influenced by the abutment zones of more than one pillar line. The term pillar-line point has been used for many years in the Appalachian region for such a situation. Point is used in the geographical rather than the mathematical sense. 3) In pillar-line extraction the following practices are safest in preventing bumps: a. The mine layout should provide for pillars of uniform size and shape along the extraction line. b. The mine layout should be planned so that no development need be done in the abutment zone of a pillar line. c. The layout should permit open-end extraction of pillar lines from the next goaf, so that it will not be necessary to resort to pocket mining, splitting pillars, or any practice that will involve driving in the direction of the goaf within the abutment zone. d. Pillars should be large enough to support area without undue roof and floor convergence before establishment of a pillar line. These are, of course, generalities, and while they are useful in laying out areas where bumps can be expected, they are of limited help in many mines that were committed to a system of mining before it was realized that they were subject to bumps. Under such conditions it becomes necessary to choose between the following alternatives: 1) Abandon the territory, except for pillars that offer no extraction problems. 2) Through experience select the pillars that are most heavily loaded, and, by augering, induce bumps from a safe vantage point so that impinged loads are relieved. This method was first developed at the Gary, W. Va. mines of U. S. Steel Corp. and later adapted to mining thick coal beds at Kaiser Steel's Sunnyside mine in Utah. No scientific method is available to determine where to drill within a loaded pillar. Although this method of unloading has worked very successfully at Gary—with one exception—

Jan 1, 1959

By Pedro Bolsaitis, Paul M. Sullivan

The activities of zinc in liquid Zn-A1 alloys in the temperature range of 1000' to 1160°K were determined by means of the isopiestic technique. The results are in reasonable agreement with the previous values determined by the radioactive tracer dew point method. Slightly negative excess entropies of mixing were found. The measured activities suggest that the a function for these alloys is not a constant, as has frequently been assumed, but is better represented by two straight line segments of different slopes. THE thermodynamic data of Al-Z alloys have been the subject of investigation by many authors. However, in the recent compilation of such data by Hult-gren et al.,5 the conclusion is reached that none of the previous measurements are reliable or consistent with each other. Since then two new sets of measurements have been reported,2, 8 both laying claim to good accuracies, yet showing very significant disagreement in the measured activity coefficients of zinc in Zn-A1 alloys and in the magnitude and sign of the excess entropies of mixing. Information on the thermodynamics of the system is of particular interest for interpreting results of the Bureau of Mines research on refining of zinc by distillation of die cast scrap. The present study was undertaken as an independent check on the recent values obtained from dew point measurements 8 and electromotive force measurements.' The isopiestic method, first introduced by Herasy-menko,' was chosen because it is one of the few thermodynamic techniques which, in principle at least, is carried out under perfect equilibrium conditions. The disadvantage of the method is that data are obtained at various random compositions and temperatures, which makes the interpretation somewhat cumbersome. The random errors arising from temperature gradients and fluctuations appear to be comparable to those of other techniques, as evidenced by the magnitude of the estimated uncertainties in the calculated integral thermodynamic quantities. An advantage of the method is that each run provides a relatively large amount of data; thus, it is less time consuming than those methods where samples of each composition must be measured individually. EXPERIMENTAL PROCEDURE The activities of zinc in liquid Zn-A1 alloys were measured by the isopiestic method which uses the principle of the tendency toward equilibrium of a series of samples at various temperatures under an imposed vapor pressure of the more volatile component (i.e., zinc, in this case). The basic apparatus is shown in Fig. 1. The small graphite crucibles that contained the metal samples were 15 mm ID and 13 mm deep with approximately 3 mm wall thickness. Each crucible was notched at the top and bottom to allow easy passage of vapor from one to another. At the beginning of an experiment each crucible was weighed on an analytical balance. Zinc and aluminum of spectrographic purity (99.999 pct) were then weighed into the crucibles. The amounts of each metal added were such that initial compositions varied above and below equilibrium values. One crucible contained only pure zinc. After weighing, the crucibles were stacked with the pure zinc on the bottom (corresponding to the lowest temperature in the furnace) and richest aluminum alloys at the top. The entire stack of crucibles was then placed in the silica glass container "E" which was then sealed under vacuum. Sixteen to twenty calibrated Chromel-Alumel thermocouples were attached by wire along the length of the silica tube, one or more adjacent to each sample.

Jan 1, 1970

By Frederick Prime

The Great or Cumberland Valley, which (under a variety of names) extends from Canada, through Vermont, Massachusetts, Connecticut, New York, Pennsylvania, Maryland, Virginia, and East Tennessee, to Alabama, is composed in part of limestones lying immediately above the Potsdam sandstone. Geologically, they belong to the era between the Potsdam and Trenton, and are commonly termed Calciferous. A peculiarity of these limestones is their great richness in limonite or brown hematite ores, which form a large part of the charges of the many blast-furnaces situated on their outcrops. The mines from which the ores are obtained are (properly speaking) only pits or quarries, from which 'the ore is extracted by means of picks or shovels, powder being rarely employed. The ore does not occur casually at any point in the limestone, but forms regular lines, following apparently the outcrops of certain beds. In Lehigh County, Penn., where 1 have been engaged on the Geological Survey of the State, during the past season, there are three or four of these lines. During the progress of the survey I was much struck by the fact that the two most important and promising lines of outcrop were, one at the base of the crystalline schists (forming the South or Lehigh Mountain), and overlying the Potsdam sandstone conformably; the other, near the line of junction of the calciferous limestone with the slates of the Cincinnati epoch. The mines along these two lines, following the topography of the country, were in place, richer and more permanent than those of the belts between, which were generally leaner. A peculiarity of these two lines of outcrop, and one to which I particularly desire to draw attention, is the occurrence of what I at first mistook for a highly altered slaty limestone, but which subsequent analysis proved to consist in great part of damourite (hydrated potash mica). The following are analyses of this damourite slate: I. From Fogelsville, Lehigh County, within a few hundred feet of the contact of limestone and slate, by Dr. F. A. Genth. 11. From Hensingerville, Lehigh County, within 300 feet of gneiss, by Mr. Sydney Castle, of the University of Pennsylvania. 111. From Allentown, Lehigh County, within 150 feet of con

By William A. Johnson, Robert F. Mehl

It is now recognized that several important types of reactions in metallic systems proceed by the formation of nuclei and the growth of these nuclei. The process of freezing is a simple example of this, as Tammann pointed out years ago.1 Tammann held that the rate of freezing is determined by a rate of nucleation, expressed as the number of nuclei formed per unit volume of unfrozen liquid per second, and a rate of growth of these nuclei, expressed as the linear rate of radial growth in units of length per second. For isothermal freezing the conception is simple; for ordinary freezing, extending over a range of temperature, it is not as simple, for the values of the two constants must change with change in temperature. There is ample evidence that the postulated mechanism is correct even though a quantitative derivation of the rate of isothermal or of ordinary freezing in terms of the two constants has been lacking. In recent years other reactions have been found to proceed in a similar fashion. It has been well established, particularly by Bain12-8 that the formation of pearlite from the eutectoid decomposition of the solid solution austenite proceeds in such a way, and Polanyi and Schmid, Tammann and Crone, Karnop and Sachs, and others9-11 have shown that the process of recrystallization proceeds in a similar way. Isothermal reaction rates have been determined for eutectoid decomposition by a number of investigators. Bain's2-8 work on the formation of pearlite from austenite is especially valuable in this respect—the type of isothermal reaction curve obtained, as illustrated in Fig. 13, showed an initial slow rate, accelerating to an intermediate maximum rate which then decelerated to the completion of the reaction; similar curves have been obtained by Wever and his collaborators.12 Other eutectoid decompositions show similar behavior: for example, the decomposition of the beta eutectoid in the copper-aluminum system, studied by Smith

Jan 1, 1939

By William A. Johnson, Robert F. Mehl

It is now recognized that several important types of reactions in metallic systems proceed by the formation of nuclei and the growth of these nuclei. The process of freezing is a simple example of this, as Tammann pointed out years ago.1 Tammann held that the rate of freezing is determined by a rate of nucleation, expressed as the number of nuclei formed per unit volume of unfrozen liquid per second, and a rate of growth of these nuclei, expressed as the linear rate of radial growth in units of length per second. For isothermal freezing the conception is simple; for ordinary freezing, extending over a range of temperature, it is not as simple, for the values of the two constants must change with change in temperature. There is ample evidence that the postulated mechanism is correct even though a quantitative derivation of the rate of isothermal or of ordinary freezing in terms of the two constants has been lacking. In recent years other reactions have been found to proceed in a similar fashion. It has been well established, particularly by Bain12-8 that the formation of pearlite from the eutectoid decomposition of the solid solution austenite proceeds in such a way, and Polanyi and Schmid, Tammann and Crone, Karnop and Sachs, and others9-11 have shown that the process of recrystallization proceeds in a similar way. Isothermal reaction rates have been determined for eutectoid decomposition by a number of investigators. Bain's2-8 work on the formation of pearlite from austenite is especially valuable in this respect—the type of isothermal reaction curve obtained, as illustrated in Fig. 13, showed an initial slow rate, accelerating to an intermediate maximum rate which then decelerated to the completion of the reaction; similar curves have been obtained by Wever and his collaborators.12 Other eutectoid decompositions show similar behavior: for example, the decomposition of the beta eutectoid in the copper-aluminum system, studied by Smith

Jan 1, 1939

By Claus Guenter Goetzeil

(New York Meeting, February, 1937) The object of this investigation was to determine whether silver alloys could be used instead of the currently employed insert of high-expansion Average Coefficient per Deg. C. over Range 20° to 200° C. Pure aluminum..................................... 24.6 X 10-6 Cast low-expansion Si-Cu-Ni-A1 piston alloy............ 20.0 X 10-6 High-expansion austenitic Cu-Ni cast iron.............. 19.3 X 10-6 Cast steel (0.25-0.35 C, 0.40-1.0 Mn).................. 12.6 X 10-6 Cast iron (3.15 total C, 2.16 Si)....................... 12.8 X 10-6 Pure silver.......................................... 18.9 X 10-6 austenitic ferronickel alloy, to reduce the wear of ring grooves in light metal pistons. A typical example of a piston containing a ferronickel insert is shown in Fig. 1. The high coefficient of expansion of silver made it worthy of consideration, while the small size of the insert would render its use feasible in Germany as an emergency measure. The coefficients of linear expansion of several metals and ailoys are as shown in the table above. Obviously the melting point of the insert must be high enough to prevent it from melting when the light alloy is cast around it. This imposes a lower limit of about 850" C. for the solidus of the silver alloy. Pure silver melts at about 961" C., so that the tolerable depression in the solidus is rather small. To avoid deformation of the insert during use a Brinell hardness number of at least 60 appears necessary.

Jan 1, 1937

By F. G. Miller

Earlier studies of the mechanism of flotation showed that coal flotation products are contaminated by composite coal and mineral particles. The mineral matter of these particles has the dual effect of increasing the specific gravity and decreasing the coal surface of the particle available for bubble attachment. The present study showed that these particles are more loosely held in the froth column than the high grade coal particles, especially in the coarser sizes. Consequently, it is possible in the laboratory to produce a secondary concentration of the product by sprinkling the froth product with water to wash these loosely held particles from the froth during formation and recovery. To improve coal flotation, Bethlehem Steel Corp.'s research department has been working on a number of related problems based on both physical and chemical factors. The ideal is of course full understanding of the interrelated effects of both sets of factors. However, detailed studies1 of each physical factor have produced immediately usable results in commercial coal flotation and are providing the basis for our current work on the effect of chemical factors. Since these detailed studies provided the basis for the present investigation of froth sprinkling, their key results are highlighted here. For example, for a highly floatable bituminous coal, particle floatability was shown to be directly related to the percentage of coal surface available for bubble attachment and inversely related to particle mass. The data also underscored that in a given size range the addition of mineral matter to a particle makes flotation more difficult both by adding to the mass of the particle and by decreasing the amount of coal surface available for bubble attachment. Size also affects particle floatability in that as the size of particles of a given specific gravity increases, mass increases and the ratio between coal surface area and mass of the particle decreases. Flotation tests showed that any recovery of the coarsest particles in a coal feed is accompanied by progressively higher recovery of finer and finer particles. Consequently, fine high-specific-gravity particles are recovered with the coarse good coal. As a result, when the entire 14 mesh x 0 size range is processed by froth flotation, the good coarse coal is contaminated with high-specific-gravity fines. It is the small quantities of these fines that must be rejected from the froth product if flotation efficiency is to be increased above its present level. These principles and findings, together with work by Professor V. I. Klassen,' led to the froth sprinkling investigation reported in this paper. Working with Russian coals, Klassen had shown that froth sprinkling washes loosely held refuse particles from the froth and compensates for the water lost in the upper froth layers and increases its stability. As a result, the coal particles are retained in the froth and the loss of coarse coal from the froth is prevented. Decreases in ash of 0.1% to 1.5% were reported by Klassen. Working with a 28 mesh x 0 American coal, the author of the present paper found that single-stage flotation coupled with froth sprinkling produced a product comparable to that obtained by the more expensive method of roughing and cleaning.3 The investigation reported in the present paper expanded study of the effect of froth sprinkling to include each of the standard size fractions of a bituminous coal. The main findings are as follows: (1) For those size fractions between 48 mesh and 150 mesh, froth sprinkling produces a marked reduction in both sulfur and ash. In the case of those sizes coarser than 48 mesh, while this reduction is not as significant, the additional benefit of shorter retention time is still a plus for froth sprinkling. Furthermore, when froth sprinkling is coupled with normal fast flotation, the product purity approaches that obtained by starvation reagent feeding, i.e., gradual feeding of flotation reagent to float the recoverable coal from the pulp slowly in several increments. The specific results for these two size groups are: (a) 14 x 48 Mesh. By using froth sprinkling with fast flotation, product sulfur can be reduced to a level

Jan 1, 1970

By Donald D. Smythe

Tars paper describes briefly the topography and geology of the region where the mica-bearing pegmatites are found and discusses prospecting, the quality of the mica, its preparation, and evaluation of the deposits. Muscovite mica occurs in a number of widely separated localities in Brazil, but production has come largely from deposits in the southeastern and eastern part of the State of Minas Gerais (Fig. I). There the deposits form a discontinuous zone, which starts at a point 90 km. north of the city of Rio de Janeiro and extends north for some 500 km., roughly parallel to the coast. A maximum width of 180 km. is reached along the Rio Doce. To the west in Minas Gerais, and extending east into the states of Espirito Santo and Rio de Janeiro, the mica zone proper is fringed by areas in which there are scattered occurrences of mica-bearing pegmatites. A few of these outlying deposits have produced commercial mica, but most of them are unimportant. To the southwest, in the State of São Paulo, there are a number of mines, which at one time produced a very considerable amount of sheet mica, largely as a by-product of kaolin mining. These deposits, and, a few others lying between them and the main productive areas to the northeast, appear to be the southwestern continuation of the strong Minas Gerais mica zone. In the vicinity of Conquista, just north of the Minas Gerais boundary in the State of Bahia, and still farther north, near Jacobina, there are several known mica deposits. Their location indicates that they may be the northern continuation of the main mica zone. The major part of Brazilian mica production has come from four areas within the mica zone proper; from north to south, Governador Valadares, Raul Soares, Espera Feliz, and Muriaé. The first is 190 km. from north to south and reaches a maximum width of 180 km. The Raul Soares area extends 135 km. from northeast to southwest, and in places is 80 km. wide. The Espera Feliz area is 100 km. from north to south, and reaches a width of 35 km. The Muriaé area extends 150 km. from northeast to southwest and its width reaches 40 kilometers. Between the known productive areas, and in the areas directly to the southwest and to the north of them, little mica has been produced. These gaps, as well as certain irregularities in the outline of the mica zone itself, are to be ascribed either to lack of prospecting or to conditions preventing the discovery of mica, rather than to its nonexistence. Elsewhere in Brazil mica has been reported from eastern Goiaz, Ceará, Pernambuco, Rio Grande do Sul, Matto

Jan 1, 1946

By Ernest F. Burchard

(Pittsburg Meeting, March, 1910.) IN connection with the work of testing structural materials for the use of the U. S. Government at the laboratories of the technologic branch of the U. S. Geological Survey at St. Louis, Mo., from September, 1904, to April, 1909, and since then at Pittsburg, Pa., large quantities of sand, gravel, and crushed stone have been needed from time to time, besides samples of building-stone, clays, and other quarry-products. In many instances it has been necessary to obtain single samples of sand, gravel, or crushed stone in lots of a car-load or more. For obvious reasons all these collections have had to be made by a representative of the Survey. As the work progressed it was found essential that numerous geologic data should be gathered regarding the materials collected, in order that they might be properly classified as to kind of material, source, geologic age, etc., and that they might be rated according to quantity available, accessibility to transportation facilities, approximate costs, suitability for special purposes, etc., and that notes might be taken regarding undeveloped deposits of possible value. Furthermore, it was desired that the selection of materials for tests should be made broadly, so as to cover, first, the representative types of material, and later, if possible, the typical materials of the more important building-centers in the United States. In order to insure a certain degree of uniformity in this work and economy of effort and expense, it was decided that as much of the sampling as was practicable should be done by a member of the. geologic branch, whose regular field-trips could be combined conveniently with those necessary for procuring materials for the laboratory. During parts of the last three years I have been engaged in field-work of this sort.

Jun 1, 1910

By A. M. Turkalo

IT is a well-known fact that martensitic steels show a greater resistance to brittle fracture than do pearlitic and bainitic steels. It was, therefore, thought worthwhile to investigate the mode of brittle fracture with respect to structure by studying the effect of various austenite decomposition products on the propagation of brittle fracture in steel by means of electron microscopy. Newly developed replication techniques together with the advantages of the electron microscope such as great depth of field, available high magnification and easy adaptation to stereophotography make electron microscopy very suitable for fracture studies. EXPERIMENTAL PROCEDURE An essentially plain carbon steel containing 0.56 pct C, 1.30 pct Mn, 0.02 pct P, 0.03 pct S and 0.22 pct Si was used in this investigation. The following table gives the heat treatments used to obtain the various austenite decomposition products: The resulting austenite grain size from the 870°C austenitization treatment was about an ASTM No. 7 grain size. The specimens which were 2 in. long, 1/4-in. diam bars were austenitized in a tube furnace through which argon gas was blown. The tube was not, however, air-free and the specimens were not completely oxide-free. Isothermal treatments were done in a lead bath. With the exception of the fully hardened specimen and the one as-isothermally transformed at 300°C the heat treated specimens were notched in the following fashion with a jeweler's saw. A cut about 0.08 in. deep was made perpendicular to the length of the bar. The specimen then was rotated about 45 deg and another cut about 0.08 in. deep was made. In the case of the hard martensitic and bainitic specimens, only one cut was made and the depth was not controlled. The design of the two-cut notch caused fracture to initiate at the point of intersection of the two saw cuts. The specimens were broken at -196°C in a Charpy impact testing machine. In order to hold the specimens securely in the impact machine two square pieces of mild steel were made about 5/8 in. long having the same cross section as that of a standard Charpy specimen but containing a hole 1/4 in. diam through the center of the cross-section. These adapters were slipped over the ends of the test specimen which was then secured tightly by means of set screws in the adapters. The specimen with the adapters was cooled to -196°C in liquid N,, then placed in the impact machine and broken within 3 sec. One half of the broken specimen was used for the electron microscope study of the actual fracture surface. The other half was nickel-plated and a cross section through the notch and fracture was polished for electron microscope examination. Carbon replicas of the fracture specimens for the electron microscope study were made essentially according to Bradley's evaporation technique.' Both direct carbon and two-stage carbon replication techniques were used. In the case of the direct carbon technique, a thin layer of carbon was evaporated first at an angle of about 45 deg to the mean fracture surface and then another film of carbon was evaporated normally to the fracture surface. The carbon replica was freed electrolytically.2 The specimen was made an anode in a 10 pct Nital polishing solution. It was etched intermittently by shutting off the power now and then. The freed replica was washed in 40 to 50 pct water solution of nitric acid for 10 min or so, then washed in water and picked up on a screen for examination. The two-stage carbon replication technique involved first making a primary replica of cellulose * acetate from which a carbon replica was then made. One side of a strip of cellulose acetate wet with acetone was pressed lightly against the surface of the specimen, allowed to dry and then stripped. Prior to the deposition of carbon, which was done at 90 deg to the cellulose acetate replica surface, chromium was evaporated at 45 deg. After the carbon evaporation the cellulose acetate was dissolved in acetone according to the Jaffe method3 leaving the carbon replica preshadowed with chromium for examination.

Jan 1, 1961

By J. B. Dilworth

OUTCROPS of coal have bees discovered is many localities is the Philippine archipelago, and practically all of the larger islands contain deposits of this mineral. Very little prospecting has been done to determine the value of the various coal-bearing areas, but so far as known, the largest and most promising fields are found : (1) is northern Cebu; (2) is the small island of Batan, a part of the province of Albay is southeasten Luzon; (3) is the somewhat larger island of Polillo, off the east coast of Luzon, and (4) is southern Mindoro, sear the small coast tows of Bulalacao. Northern Panay, south-central Cebu, and various localities is southern Luzon, Masbate, Negros, and Mindanao also afford evidences of the existence of coal-beds, the extent and value of which have not yet bees proved. The general position of these islands and districts is shows on the map of a portion of the Philippine Islands, Fig. 1. Some of these coal-fields have been known for many years (coal was discovered is Cebu 1827 and is Batas is 1842),1 and several futile attempts were made by the Spaniards to operate mines is these districts. But owing to many circumstances, chief among which were indifferent management, the political unrest of the islands, natural difficulties of transportation, and those inherent in the mining of steeply-inclined and somewhat irregular seams, no considerable output was ever obtained from any of these mines, and the fuel required is the many departments of industrial and political life has continued to be drawn largely from Australia and Japan. These conditions exist to a great degree at present, and though much interest is the coal-deposits of the Philippines

Jan 1, 1909