Search Documents

Jan 1, 1922

By B. Blumenthal

THE present investigation was planned as a survey of the lead-rich portion of the ternary lead-antimony-silver system by thermal analysis. Since, however, a rigorous application of the conventional thermal analytical method is time consuming, an attempt was made to speed up the investigation by reducing the time required for a single thermal analysis. This was done by increasing the rate of cooling to 12° to 18°C. per minute. Since such a rate does not permit even an approach to equilibrium conditions, the melt was stirred vigorously by a stirrer operating at the high rate of 665 r.p.m. This proved to be effective in obtaining cooling curves with distinct points of arrest and of excellent reproducibility, which satisfactorily compare with those obtained at a rate of 1° to 2°C. per min. with or without slow stirring (Fig. 1). By this method the lead-rich end of the lead-antimony system and a series of ternary alloys in sections parallel to the lead-antimony side of the ternary system were investigated and it was observed that the two branches of the' liquidus curve of the .binary alloys did not intersect at the eutectic temperature. An equivalent effect was observed in the ternary system. The eutectic temperature of the binary lead-antimony system was found to be 252.0°C., which confirms the recent investigation by Pellini and Rhines,1 who determined the eutectic temperature to be 251.5°C. The observation that the curves of primary crystallization of the lead-antimony system do not intersect at the eutectic temperature was previously made by Dean.2 Dean explains the phenomenon by assuming the existence of a compound Sb4Pb. He felt that super-cooling was not the cause of the phenomena because he was unable to influence them by inoculation. The X-ray investigation by Solomon and Morris-Jones,3. the metallographic investigations by Stead,4 Charpy,5 Gontermann,6 and Dean, Zickrick and Nix,7 and the numerous investigations of physical properties, definitely disprove the occurrence of any compound. The work of Dean was not confirmed by Broniewski and Sliwoski,8 whose experiments did not show any irregularity and who report a eutectic composition of 13 per cent antimony and a eutectic temperature of 250° to 252°C. at a rate of cooling of about 6°C. per min. Abel, Redlich and Adler9 then report a eutectic composition of 12.1 per cent upon reviewing the previous, publications and adding a few of their own cooling curves. In 1934 Quadrat and Jiriste10 found from careful analyses of the bottom portion of slowly cooled hypereutectic melts that the eutectic contains only 11,4 to 11.5 per cent antimony. (Previous analyses by Stead4 in 1881 gave 13 per cent:) Weaver," however, reported in 1935 that cooling curves indi-

Jan 1, 1943

By E. G. Leonardon, C. Schlumberger, M. Schlumberger

Last year the authors presented a paper that discussed the various electrical measurements they perform in drill holes, which they name "electrical coring."' The object of the present paper is to give a brief account of the points of scientific interest that have been elucidated by further field work and laboratory research, as well as the economic results that have been attained recently. The practical examples given in this paper are drawn, for the most part, from the field work performed in Russian oil fields during the years 1931 and 1932. This is due to the fact that, thanks to the comprehensive cooperation of the Russian geologists and scientists, the authors are allowed to make public a large amount of recant information. In other countries in which the authors are engaged in similar work, the competition between private companies makes it imperative, for a considerable lapse of time, to avoid publication of the results obtained. The following points will be discussed successively, under separate headings: 1. Electrochemical phenomena in drill holes. 2. Stratigraphic correlations and tectonic studies. 3. Relations' between the productivity of oil horizons and their electrical resistivity. 4. Location of coal seams. 5. Summary and conclusions. Electrochemical Phenomena in Drill Holes Technical Publication 462l described the author's discovery concerning the existence of important differences of potential spontaneously gener-

Jan 1, 1934

By Harrison R. Cooper

With problems of diminishing ore grades and increasing cost of facilities, the mineral industry is acutely aware of the needs for improving beneficiation processes. Industry and universities are directing intensive technical effort to develop- ment of techniques with potential for using digital computers in automation and process analysis. The main problem of early attempts at on-line computer process control methods was that of economics. Now, with new advances in analysis and modeling making practical application economically important, it appears that minerals beneficiation is on the threshold of a significant jump in operating technology. In reviewing this work, particular note was taken of research and development applied to fundamental processes and the significant areas of effort where operations research techniques are used for process applications leading to the current state-of-the-art. Development of data automation and on-line control methods for process industries is deferred to the next section of this volume. This section deals with computer-facilitated mathematical-modeling development and reviews this work in conjunction with associated prior fundamental research leading to development of the methods. Flotation The 1960 state-of -the -art in flotation modeling was com- piled by Arbiter and Harris in the volume, 50th Anniversary of Froth Flotation, edited by Fuerstenau1. Many workers in the field of flotation initiated their research through flotation models, and this effort has led to use of simulation and operations re search methods employing computer techniques to facilitate advance of this work. The flotation model of Imaizumi and Inoue, published with supporting data in 1962, was expanded in 1968 with the objective of developing a basis for process automation.2,3 The fundamental work of Woodburn and Loveday in 1965 has led to techniques applicable to flotation circuit design optimization.4 This analysis is described in this volume by Woodburn in conjunction with King, Buchalter, and Piper. Niemi5,6 derived models for dynamics of a flotation circuit which were employed in developing a model describing

Jan 1, 1969

By George F. Comstock

It has been known for many years that the alloy containing 90 per cent. copper and 10 per cent. aluminum can be hardened, like steel, by quenching from a suitable temperature, and that the hardened alloy can be softened again by annealing or drawing the temper. It does not seem to be generally appreciated, however, that the effect of the first slight reheating after quenching is actually increased hardness, the softening effect not taking place until a certain temperature of "drawing" has been exceeded. This paper gives the results of a few experiments on various specimens of cast 10 per cent. aluminum bronze, quenched for maximum hardness, and subsequcntly annealed at different temperatures. The hardness measurements were made with both a scleroscope and a standard Swedish Brinell machine; some peculiarities of the scleroscope test on this material are described. The author is not aware of many previous investigations of the hardness of this alloy when quenched and drawn, but two important papers on the subject should be mentioned. The earliest was by Portevin and Arnou,1 in which it was stated that tempering quenched 10 per cent. aluminum bronze at 400" C. increased the hardness as compared with the quenched untempered alloy and that reheating above that temperature ' was necessary to obtain any softening effect. A later paper was by Seidell and Horvitz,2 who mentioned Portevin and Arnou's work, but did not report any increase in hardness obtained

Jan 1, 1925

By A. T. Tye

REGARDING the results of preferential flotation at Cananea, Weinig has stated that "The concentrating mill of the Cananea Consolidated Copper Company at Cananea, Mexico, furnishes an excellent example of modern flotation practice. The complete figures are given because they present so forcibly the advantages of modern selective flotation."' L. 0. Howard notes that "Perhaps the outstanding example so far published of improvements in results through the use of selective flotation is that at Cananea, Mexico."2 The following notes indicate the conditions under which the results were obtained at Cananea; also the effect of preferential flotation at the concentrator and at the smelter. In the majority of cases the full benefit of selective flotation is not fully realized, as the concentrates are shipped from the mill to smelters owned by other companies. The saving made at a certain concentrator by this method of flotation may be well understood but the saving resulting at the smelter from the results of preferential flotation at the mill is not so apparent, as the data are contained in the smelting records of some other company. Even at the smelter the great gains following preferential flotation may not be noted, as a variety of ores and concentrates from various sources are received and the difference from the changed concentrator operations of a certain mill may be obscured. As noted by Professor Weinig and Professor Howard, the results obtained at Cananea brought about a veritable metallurgical revolution at the smelter.

Jan 1, 1927

By Charles Catlett

(Chattanooga Meeting, October, 1M.) THE terms " developed " and " undeveloped " are necessarily relative and cover a wide range; but the latter is here applied to cases in which the information at hand falls short of a clear demonstration of values, and conclusions must be reached from a study of the geological conditions of the particular deposit, interpreted in the light of similar and closely related deposits. Such an inquiry might be characterized as an effort to reach reliable conclusions from insufficient data. But the engineer engaged in commercial work finds himself often face to face with apparently such problems; and while he may realize with regret that a small amount of intelligent development would add enormously to the value of his conclusions, he is compelled to recognize the demand of a business situation for a prompt decision as the basis of immediate action. In a case within my knowledge, the question involved was the purchase of 50,000 acres of coal-land, and 10 days was the limit within which this question must be decided. Of course, it was impossible to make a satisfactory examination within that time; but the 'instructions were "to make the most complete examination and the most positive recommendation possible." Such instructions are often given; for, no matter how much time an investor may have, he is likely to put of his decision until the last moment, and then discover that he needs more light and advice. It does not follow that engineers, after full explanation and mutual understanding of the situation, should decline to undertake examinations thus limited. In the case just mentioned, while only the broadest view was possible, half the time available was sufficient to show that the property was a good purchase. The timber alone was subsequently resold for more than the entire purchase-price of the

Mar 1, 1909

By Ford R. Bryan, Edward F. Runge

BECAUSE of the need for ductile heat resistant alloys of non-strategic composition, there has been metallurgical development of Fe-A1 alloys possessing improved ductility and hot strength, together with high oxidation resistance. Iron and alu- minum form solid solutions up to approximately 35 pct Al. Alloys in the 8 to 12 pct A1 range are characterized by excellent oxidation resistance, high electrical resistivity' and, when appropriately alloyed, have creep rupture strength equivalent to that of the austenitic stainless steels.' At higher aluminum levels, the magnetic properties are of considerable interest. Nachman and Buehler" have recently reported on the desirable magnetic characteristics of the 16 pct alloy.

Jan 1, 1957

By E. J. Quinn, M. F. Fogler

In a recent paper, Rawdon and Mutchlerl gave some exceptionally interesting results on the Brinell and scratch hardness of severely cold-worked metals. In their work, they found that, on continued cold rolling, the metal hardened up to a particular point and then reversed and became softer; this was true for both Brinell and scratch hardness values. The generally reported behavior2 of metals, with respect to Brinell tests on cold-worked material, is that the metals harden up to a certain point and then, on further cold rolling, no change in Brinell hardness occurs. Jeffries and Archer3 state that there is little difference between the scratch hardness of annealed and cold-worked metals; the work of Faust and Tammann4 also indicated no difference between the hardness of annealed and cold-worked copper. Rawdon and Mutchler found, when they plotted the reduction ratio (initial thickness divided by thickness after rolling) against the hardness value for the cold-rolled material, that the hardness number increased up to a reduction ratio of about 3 and then decreased and became even smaller than that for the annealed metal. This behavior was reported for both scratch and Brinell hardness; Figs. 1 and 2 show their results for Brinell hardness on the metals for which they published data. This is an exceptionally interesting phenomenon, if it occurs under all conditions of rolling, and would have an important bearing on the practice of cold

Jan 1, 1925

By R. W. Newcomb

THE constancy of calibration, and to a great extent the life, of a thermoelement is dependent on the suitability of the primary protecting tube in which the wires are mounted, particularly when used at high temperatures. An ideal thermocouple protecting tube would be com-posed of materials that would not contaminate the thermoelement wires contained in it-one that would remain absolutely gas-tight ,it all temperatures of usage, that will not be attacked by gases, or other surrounding agencies, that is not destroyed by heat, that withstands sudden and extreme temperature changes, that affords a high degree of mechanical protection and does not deform at high temperatures, that is a good heat conductor and obtainable in small diameters so as to keep down lag factors. It has not yet been possible to produce tubes of any known mate-rials that will meet all of these conditions. In selecting protecting tubes, therefore, one should be chosen the characteristics of which best fit it to the particular conditions of usage. Frequently conditions are such that two tubes have to be used, a primary gas-tight protecting tube inside of a secondary protecting tube, because certain agencies will attack the primary gas-tight tube unless it is guarded by the outside tube.

Jan 9, 1919

By D. F. Coolbaugh

Successful mine exploration requires sound planning and modern exploration techniques, but it also requires perseverance and the right timing. The La Caridad mineral area has been known for over 70 years, but as with many mines, it was not "discovered" until viewed under new economic conditions and exploration philosophies. Present exploration of the La Caridad area began in 1964 and was carried out under a joint Mexican Government-United Nations Project. Detailed exploration was begun by Asarco Mexicana S.A. in late 1968. The geology of the La Caridad deposits conforms, generally, to the "porphyry copper" deposits of Arizona. However, breccias and pegmatites play a very important part in the emplacement of mineralization.

Jan 1, 1972

CONTENTS PAGE SOUTHWARD, GLENN B.-Coal Mining by the V System. Discussed by Glenn B. Southward, Howard N. Eavenson, Edward B. Raiguel, Thomas de Venny, J.. J. Rutledge, Graham Bright 1 ARMS, RAY W.-Dry Cleaning of Coal. Discussed by Ray W. Arms, S. A. Taylor, Howard N. Eavenson, W. R. Crane, F. F. Jorgenson, G. R. Delamater. 6 EAVENSON, HOWARD N.-Data About Labor Employed in Various Bituminous Coal Mines. Discussed by Howard N. Eavenson, George H. Ashley, E. A. Holbrook, S. A. Taylor, R. V. Norris 14 Coal Mining by the V System Discussion of the paper of GLENN B. SOUTHWARD presented at the New York Meeting, February, 1924, and issued as Paper No. 1300-C, with MINING AND METALLURGY, February, 1924. MEMBER.-How do you pay your men for loading? GLENN B. SOUTHWARD.-Everything is on time basis. MEMBER.-How many men do you have loading across one of the diagonal faces? GLENN B. SOUTHWARD.-From four to five, depending on the length of the face. Our loaders are so arranged that each will give about twenty-five tons per loader a day. MEMBER.-How much timber do you use? GLENN B. SOUTHWARD.-A little more than will be used in room-and-pillar work, but not a great deal more. We have not attempted to recover much of our timber. MEMBER.-IS the mine union or non-union? GLENN B. SOUTHWARD.-Non-union. HOWARD N. EAVENSON, Pittsburgh, Pa.-I went .through that mine some weeks ago, and think that the author has been very conservative in his statements about the amount of loadings, etc. EDWARD B. RAIGUEL, Huntington, W. Va. (written discussion).¬Page 7 shows 60 men employed in day and night shifts, inside the mine, producing 750 tons per day. Let us reduce these figures to a man-hour basis, for comparison with Mr. Eavenson's figures on West Virginia mines, as follows:

Jan 6, 1924

By William H. Morris

At the Glen Summit meeting, the question of controlling the silicon in pig-iron WAS raised; and as this has been deemed by most furnace-men for years past a matter of special difficulty, an account of our experience in the matter may be of interest. When running on mill-iron, some years ago, we aimed to keep

Jan 1, 1893

By B. M. Larsen

Attempting to review the fundamental aspects of segregation in steel ingots of all types in a paper of reasonable length, we encounter two difficulties: (I) the fact that a large number of different physical and chemical effects are involved, and (2) rather incomplete and confusing evidence on certain aspects of detail and mechanism in the freezing process in which the segregation effect is involved. The best solution seemed to be to link together most of the underlying factors into a simplified theoretical picture that appears to the writer to explain most of the observed data, in the hope that this will serve as a reasonably good target for discussion and criticism. Segregation effects, especially in steel ingots or castings, are often divided into " microscopic" and "macroscopic," depending on whether the variations in concentration of solutes or dissolved elements in the iron occur as: (I) a periodic variation over the small distances between the nuclei and the surfaces of the primary grains, or (2) as a larger scale effect involving concentration gradients over distances of the order of several inches, more or less. The reason for this somewhat artificial division is, of course, that it is only the macroscopic scale effect that has much practical importance. About the only effect of practical importance that results from microscopic segregation is the banded structure often left in rolled sections, and even this is relatively harmless in most cases. However, the causes of microscopic segregation also untlerly the larger scale effect, so we must first consider matters such as the formation and growth of crystal nuclei, selective freezing and diffusion, and others that are fundamental to all sepregation effects. Undercooling and Nuclei Formation It is probable that although the degree of undercooling is small in iron, as in metals in general, a certain amount of it takes place, and also that the number of crystal nuclei increases very rapidly with increased undercooling below the liquidus temperature. In practical terms this means that the nuclei number illcreases very rapidly with increased cooling or freezing rate, thus being dependent on the rate of heat flow out from the zone of crystallization. Temperature Gradients and Heat Dissipation during Freezing Each pound of steel evolves about 100 B.t.u. when freezing. In addition to this, the temperature gradient in the solidified portion (required to dissipate the heat as freezing progresses into the axis) necessitates a loss of heat required to cool the solid metal below its freezing range, which is equivalent to an amount of not so much less in magnitude. In a 5-ton ingot, the total would include about one million B.t.u. for freezing alone and about 0.4 to 0.5 million B.t.u. for the gradient, up to the end of the freezing period. Thus the rate of freezing depends primarily on the rate of heat dissipation. In the ordinary ingot shapes, the axial rate of growth of the solid

Jan 1, 1945

By Erhard Hornbogen

Twins were propagated into large, well-annealed crystals of a, iron-phosphorous and a, iron-molybdenum solid solutions. Strain fields caused by interaction of these twins were made visible by precipitation. These strain fields can be explained by assuming that transmitted and reflected plastic waves are created when a twin strikes an obstacle with high velocity. The twin front itself can be regarded as a shear wave that may be able to develop a one-dimensional shock front. The occurrence of {WO} fracture by the reflected stress is also discussed. The described effects were not found when twins propagated at lout velocity into disturbed crystals, for example, into crystals previously deformed by slip. DEFORMATION twinning leads to shearing of a crystal lattice under external load. The shear appears to be homogeneous over a large number of crystal layers. In a iron, shear occurs on the (112) planes and in the <1ll> directions. The formation of a twin proceeds by the movement of partial dislocations that change the stacking at the twinning plane.l, In the bcc lattice, this partial dislocation can be created by dissociation of a sessile a/2[111] dislocation that lies in the (112) plane: Cottrell and Bilby&apos;s spiral mechanism can explain the homogeneous shear, but has not been proven experimentally. Nevertheless, this mechanism can explain the possible high velocity of formation of a twin. In Cottrell and Bilby&apos;s model, as in other models of twinning or phase transformation, a much higher energy is required to spread the first stacking fault than to add new layers by further movement of the partial dislocations. The dislocations will therefore become accelerated proportional to the difference between the stress, tN, to nucleate and tp to propagate the twin. It has been assumed3,4 that tn is the stress required to make two partial dislocations of apposite sign pass for the first time. After the first layer of new stacking has been formed, the maximum stress is TN=Gb/4pd where G is the shear modulus, b is the Burgers vector of the partial dislocation, and d is their perpendicular spacing so that the amount of shear is S = b/d. From this formula, a value of 25 kg per mm2 has been estimated for twinning in Zn3. The measured values are smaller, but local internal stresses may help to provide the necessary stress. For a iron, a higher value can be expected, mainly due to the higher value of G. That agrees with the observation that "burst" twinning occurs if the yield strength is in-

Jan 1, 1962

By Hugh H. Waesche

AN adequate supply of crystalline quartz of piezoelectric grade and size continues to be of fundamental importance to the U. S. Army Signal Corps. Current electronic development programs of the Armed Forces depend upon the use of quartz crystals in all applications where accurate frequency control is necessary. In peacetime this&apos; may not seem too significant, but in planning for possible national defense emergencies, an adequate supply of piezoelectric grade raw quartz is just as important as an adequate supply of some of the more publicized strategic minerals. Prior to World War II, the Signal Corps accepted the use of quartz crystals for frequency-control purposes in essentially all electronic communication, navigation, and radar equipment operating in the audio and radio frequency spectra up to and including the ultra-high-frequency channels. Over 4,000; 000 lb of radio-grade quartz was required between January 1942 and V.J Day. Use of such a large quantity of crystal units was necessary in order to establish and maintain, with a minimum of effort, clear and definite frequency channels of greater stability than could be obtained by any other means. This policy was justified on the basis that quartz was without a peer as a frequency-controlling element. Military and civilian uses of quartz in the field, as well as laboratory studies, have confirmed this premise and no means of highly stable frequency control, superior to quartz, has been discovered. It appears certain that the demand for use of quartz for frequency control purposes will continue at a high level.

Jan 1, 1948

By Tkeoclore Marvi

IT is singular that an industry quite the antithesis of flying should record tremendous strides in the utilization of aviation through- out the entire depression period, .while in the same years private interests lagged and airplatie manufacturing plants closed to such an extent that he purchase of new planes of certain types was practically impossible. Though receiving little notice from aviation publications and national associations, this use of the airplane progressed by sheer merit. It saved money, conserved energies, and made minutes in the air the equal of weeks on foot or water. The advent of aviation into mining and petroleum operations dates back many years, yet it \vas not until the depression that this new facility of the mineral industry was put on its proper economic basis. There, by its possibilities for saving effort, time, and money, it takes its place equally with other great technical advances in nietl

Jan 1, 1934

By Claiborne C. Van Zandt

THE heavy postwar demand for Portland Cement has created shortages that are gradually being overcome by increases in plant capacity. In the post-war period, the Lone Star Cement Corp. has expanded several of its existing 15 plants and has built 2 new plants, now in operation, with a third new plant under construction in Brazil, of design somewhat different from that of the two preceding ones. The new domestic plants are located at Lone Star, Va., near Roanoke, and at Maryneal, Tex., near Sweetwater, and went into operation during 1951. Each plant is equipped with two rotary kilns and has an initial capacity of 1,500,000 bbl per year, or 6,000,000 sacks. The total cost of each plant was about $10,500,000, and on this basis $7.00 in 1951 money are required per bbl of annual capacity; at 376 lb per bbl, this corresponds to $37.00 per ton of output. The investment corresponds to approximately $80,000 per hourly-wage earner employed. The purpose of this paper is to describe the most interesting design features of the two new and almost identical Lone Star plants. Why the Dry Process Was Chosen The two new domestic Lone Star mills employ the dry process because: 1-The raw materials at both properties are particularly suitable and can be dried very, readily. 2-The Maryneal, Tex., plant does not have water available for slurry. 3-Very substantial kiln fuel savings can be obtained. 4-Dry raw grinding reduces ball and liner wear and- general maintenance, without any sacrifice in power. Operating costs to date have more than justified the choice of the dry process for these two plants. Raw Materials The chemical composition of Portland Cement raw material after crushing, grinding, and mixing, but before burning, is about as follows: [ ] sometimes tailings from an iron ore concentrating plant. Certain objectionable materials occur in raw mix: magnesia, limited in cement to 5 pct, in excessive amounts; alkalies, as sodium and potassium; phosphorous; and sulphur, generally present in coal and oil. The Roanoke raw, materials are dense limestone and shale. The Maryneal materials are soft limestone and a hard brittle clay that can be handled much like shale. Sand and iron ore are required in small quantities. General Plant Layout and Construction The two plants are so similar that one joint description will cover both, with such exceptions as will be especially indicated. The crushing plant is located in the quarry, and raw material is conveyed by belt to the storage building, where all materials are stored and handled. Fig. 1 identifies the various structures of the Roanoke plant. The large storage building is used for the storing and handling of all materials, including limestone, shale, sand, iron ore, coal, clinker, and gypsum. Directly adjoining the storage building is a structure under a similar arched roof, containing the raw and clinker grinding departments and the electrical substation. The discharge ends of kilns and coolers, and coal or gas burning equipment are also placed at one end of the mill building. The 340ft long kilns extend away from the main buildings to form the long leg of an L, at the end of which is the feeding and kiln dust collecting equipment, and the raw blending silos are conveniently located adjacent to the feed end of the kilns. The machine shop, storeroom, electrical shop, foremen&apos;s office, service rooms, and meeting hall are combined in one structure in the center of the plant, and the office and laboratory are close by. The cement silos and packhouse do not have to be tied directly into the manufacturing process and are therefore located at a point convenient to the railroad tracks.

Jan 1, 1952

By M. F. Burr, F. V. Lenel, G. S. Ansell

The mechanism of materials transport was studied in a model experiment in which a silver sphere was sintered to a silver plate under an applied external stress near 800° C. For this purpose the rate of growth of the neck between the sphere and the plate which is proportional to the strain rate of the creep process involved in a neck growth was determined by measuring the change in electrical resistance of the away. This rate of neck growth will depend upon the magnitude of the applied external stress. By measuring the rate just before and just after a change in the external load and therefore the applied stress, the relationship between strain rate and stress can be derived. For material transport by slip in a pure metal it is expected that the strain rate should be proportional to the 4.5th power of the stress, while for transport by diffusional flow the strain rate should be proportional to the first power of the stress. It was found that for stresses above 5 X 10&apos; dynes per sq cm (70 psi) the exponent in the stvain rate-stress relationship was near 4.5 while for a stress of 0.7 x 108 dynes per sq cm (10 psi) an exponent of 1.8 was determined indicating that under the conditions of the experiment the transport mechanism for creep in silver shifts from diffusional flow to slip in the region of 0.7 x 106 dynes per sq cm (10 psi). The importance of these findings for an understanding of the mechanism of material transport in conventional sintering (without an external load) is pointed out. In a paper by Early et al.,&apos; the mechanism of material transport during sintering was treated as a creep process. It was pointed out that two possible types of creep processes could operate during sintering. In one of these material transport takes place by vacancy diffusion due to a gradient in chemical potential. The vacancy sinks in this diffusion process may be either grain boundaries, as in Herring-Nabarro microcreep, or regions beneath a surface of small radius of curvature. The diffusive transport may be by volume, grain boundary, or surface diffusion. In the other mechanism, creep takes place by slip, i.e., dislocation motion with its rate generally controlled by dislocation climb. One method of distinguishing between these two modes of materials transport is to investigate the creep rate, i.e., the rate of material transport as a function of stress. For material transport by vacancy diffusion, the creep rate is proportional to the stress.&apos; For creep by slip, controlled by dislocation climb, the creep rate is proportional to a power of the stress. For pure metals this power is 4.5;374 for dispersion-strengthened material a fourth power relationship can be derived.5 This difference in the stress dependence of the strain rate is illustrated schematically in Fig. 1, in which the logarithm of strain rate is plotted vs the logarithm of the stress for material transport in a pure metal by vacancy flux and by dislocation climb. The stress range in which the two types of material transport overlap would be expected to be relatively small. In the experiments described by Early and coworkers compacts pressed from spherical copper powder were sintered isothermally under an applied axial external load in a dilatometer. During sintering the magnitude of the applied external load was changed and the rate of axial shrinkage of the compact before and after the load change determined. In order to find the stress dependence of the strain rate the magnitude of the stress acting on the neck area between the spherical particles before and after the load change had to be calculated. This stress is the resultant of the stresses due both to the externally applied load and to surface tension. The stress due to surface tension is a function of the geometry of the powder compacts. It can be determined, at least for simple geometrical arrays,&apos;76 but it is difficult to obtain exact values of the stresses for actual powder compacts when only average values of particle diameters and of neck diameters between particles are available. The calculation of stress and the strain rate-stress relationship is therefore only very approximate.

Jan 1, 1968

By Charles E. Lundin, Albert S. Yamamoto

The phase eqrtilibria of the binavy system, Nb-Al, weye established by metallographic, X-ray diffraction, hardness, and thermal-analysis techniques. Three intermediate phases were identijied, Nb3.41, Nb2Al, and NbAl,. The N6,Al and NbAl phases have extensiue ranges of solubility. The maximum solubility of aluminum in niobiuitz is 23.0 i0.5 at. pct (8.0 wt pct) A1 clt 1960" i 10°C. The maximumt solinbility oj niobiunz in alunzinutz is less than 0.3 i0.1 at. pct (1.0 tut pct) fib. The A&apos;h,Al and Nbgl interinediate phases forr peritectically at 1960° 1UcC and 1870" i 1U9C, respectively, zuhereas the NbAl, phase fornts congvuently fio11t the melt at 1605" 10°C. A eutectic reaction oc- The intent of an over-all research program was to develop niobium-aluminide-base coatings for refractory metals since these coatings exhibit useful high- curs at 57.8 i 0.5 at. pct (28.5 wt pet) A1 and 1500" 10°C between NbAl and NbAl3. The aluminum-rich region of the system has a peritectic reaction where liquid reacts with NbAL, to form aluminum solid solution. Structural and lattice -pavarneter data /or the intermediate phases were determined by X-ray diffraction analyses. An unusual transfov?nation having charactevistics of nucleation-growth and martensitic nleclanisils occurs on cooling the niobium solid solution in the region from 18 at. pct (6 wt pct) Al to 23 at. pct (8 wt pct) Al. The transfornzed product on rapid quenchirzg is an acicular NhAl. temperature resistance to oxidation. As a prerequisite, the phase equilibria of the system, Nb-A1, were necessary. A literature survey revealed that the phase-equilibria data reported by various investigators were rather incomplete and conflicting. Therefore a complete determination of the system was undertaken by the authors from 0 to 100 pct of solute addition.&apos; In 1959 Savitskiyz presented a tentative diagram which

Jan 1, 1967