Search Documents

By Robert I. Jaffee, Bruce W. Gonser

Recent work by the authors1 established the constitutional diagram of the gold-germanium system. Of particular interest in the simple euctectiferous system was the eutectic alloy at 12 per cent Ge, which melted at the very low temperature of 356°C and had an unusually fine eutectic structure. It was of interest to investigate the effect of third components on the melting point, microstructure, and strength of this alloy, and in this work the effect of copper is discussed rather completely, with less complete data on the effects of silver, platinum, nickel, and zinc. No reference in the literature has been found on ternary systems with gold-germanium. Materials and Alloying -4s in the work on the binary system, gold-germanium, the germanium used in this investigation was the cyanide-reduced, 99.9 per cent product, produced by the Eagle-Picher Co. Fine gold sheet from Handy and Harmon, pure platinum sheet from the American Platinum Works, copper magnet wire from Anaconda, nickel wire assaying 99.6 per cent Ni. and electrolytic zinc were used for alloying. To make the alloys, charges of the pure metals were put in a graphite crucible and melted in an atmosphere of pure hydrogen. The temperature was brought up to about I050 C, and the metal allowed to freeze in the crucible. Except with alloys containing zinc, melting losses were consistently less than a few milligrams. When zinc was a component, weight losses up to half the weight of the zinc present were incurred, and the alloy compositions were calculated by assuming the entire weight loss to be that of zinc. In all other cases the composition of the alloys could safely be taken as that of the charge. The ingots, as solidified, were segregated, the heavier primary phases being at the bottom and sides of the ingots and the lighter primary phases at the top, but by sectioning the entire ingot vertically for microscopic examination, this factor could be evaluated. Ingots for microscopic examination weighed one gram, and those for thermal analysis weighed three grams. Thermal Analysis In this work, the eutectic line composition and thermal arrests were desired, and, after microscopic exploration had established the position of the eutectic line at a given percentage of the third component, a thermal analysis was run at that composition. The method of thermal analysis used in the work on the binary Au-Ge system,' a method particularly well suited for a small quantity of material, was used in this work. Clearly defined arrests were obtained, although with some alloys containing platinum

Jan 1, 1946

By O. George Specht, Carl A. Zapffe

IN recent print, some remarkably contradictory statements have appeared regarding the importance to be attached to sponge iron,1-6 a metallurgical commodity whose history goes back at least to the time of Diodorus Siculus in the fourth century B.C. This disagreement, however, expresses the lack of a satisfactory method for producing sponge iron rather than defection in the commodity. The blast furnace is admitted to have certain inherent disadvantages, such as a general unsuitability for magnetite and the heating and blowing of vast quantities of undesirable nitrogen, so that a workable sponge-iron process remains attractive. In this respect, low-temperature gaseous reduction shows especial promise; but confusion persists regarding the factors involved. The present paper, therefore, has three principal divisions: (I) an exhaustive examination of all previous work on low-temperature gaseous reduction, (2) experimentation on the reduction of a magnetite with hydrogen, and (3) development of certain thermodynamic relationships in reduction, with a summarized depiction of the factors in the general process. PREVIOUS INVESTIGATIONS Gaseous media used in the reduction processes under discussion can be classified in three types: (I) H2, (2) CO, and (3) other gases. In the second, the CO is often admixed with H2. The third principally comprises hydrogeniferous gases, such as natural gas and producer gas, and in addition includes chlorine. Because hydrogen therefore features in all three, a study of hydrogen reduction based on investigations using pure hydrogen alone may be incomplete. The present paper reviews the three groups of investigations in the listed order, paying particular attention to hydrogen reduction. For the benefit of future workers, an exhaustive bibliography has been prepared and similarly classified. GROUP I: REDUCTION WITH HYDROGEN Equilibria Although the present problem is specifically one of kinetics, a first consideration is the equilibrium of the system, since the reactions to be studied comprise that equilibrium, and their direction and end points are defined by it. The historic development of these researches is interesting and informative.

Jan 1, 1946

By F. Lynwood Garrison

It is not intended to make in the present paper any deduction or to formulate any theories from the results obtained by experiments. The further expenditure of considerable time and labor would be required to obtain a sufficient basis for positive assertions as to the microscopic structure of the different varieties of iron and steel, and the structural changes which take place in them. It is therefore my purpose at this time to offer simply a synopsis of the general results arrived at in a few months' work, a brief description of apparatus used, and a few hints as to the preparation and preservation of the material which it is intended to investigate. The study of the microscopic structure of iron and steel is not altogether new. Some attention has been given it in both England and Germany. But the foreign publications on the subject have thus far been confined, so far as I am aware, to two papers, one by Herr Martens, of Berlin, contributed to the Verein zur Befoerderuny des Gewerbfleisses and the other a lecture by Dr. H. C. Sorby of Sheffield. Dr. Sorby, it seems, was induced to investigate the subject as bearing on the structure of meteoric iron ; and the results he obtained are certainly very interesting. At the Boston meeting of this Institute, in February, 1883, Mr. J. C, Bayles called attention to the subject in a neat and exceedingly interesting paper, in which the work of Messrs. Martens and Sorby was summarized,* and original suggestions were added. It is at present difficult to say what will he eventually the practical value of the microscope, thus employed, in the sciences of engineering. The role which it seems most likely to play is that of' an adjunct to the testing-machine, and not (as some have supposed) a rival to the chemical laboratory. That it will be a most valuable accessory seems, to say the least, highly probable. I need hardly go at length into the details of preparing the material for examination. Mr. Bayles has described the process in such a plain and comprehensive manner that if his instructions are

Jan 1, 1886

By W. H. Ode, W. A. Selvig

By plotting fixed carbon against British thermal units of coals free from mineral matter, and ranging in rank from anthracite to lignite, it is found that the coals of higher rank, from anthracite to the higher rank of the high-volatile bituminous coals, inclusive, can be separated into groups according to their degree of metamorphism by reference to their fixed carbon. Such charts show also that the coals lower in rank can be best separated into groups with respect to B.t.u., especially when plotted on the moist basis, that is, coal containing its natural bed moisture. A tentative scheme for coal classification was presented at the October, 1932, meeting of the Technical Committee on Scientific Classification, of the American Standards Association Sectional Committee on Coal Classification. This scheme was sponsored by Subcommittee IV on Tentative Classification of Coals, under the chairmanship of W. T. Thom, Jr. It proposed the grouping of coals according to rank by reference to fixed carbon and B.t.u., on the basis of coal containing its natural bed moisture but free from mineral matter. This scheme proposed classifying coals into four broad classes: (1) anthracitic, (2) bituminous, (3) subbituminous, (4) lignitic. The anthracitic class was divided into three groups designated as meta-anthracite, normal anthracite, and semianthracite. The bituminous class also was divided into three groups, low volatile, medium volatile, and high volatile. The high-volatile group was further subdivided into four subgroups according to moisture content, as fo1lows: (1) less than 5 per cent, (2) 5 to 10 per cent, (3) 10 to 15 per cent, and (4) 15 per cent and more. The subbituminous class was divided into two groups, group 1 including subbituminous coals having calorific values of 10,500 B.t.u. or more, and group 2 including those with less than 10,500 B.t.u. The lignitic class of coal was divided into two groups both below 8,000 B.t.u., the one group consisting of consolidated and the other of unconsolidated

Jan 1, 1934

By L. E. Snow, L. F. Pett

AT the Utah Copper Pit of Kennecott Copper Corp. a versatile mobile drill unit has been developed and tested. Through increased drilling speed and additional available drilling time, an improvement of 233 pct in drill performance has been realized. Operators using drill power can quickly and easily convert the unit from a vertical to a toe hole drill. Drilling is done with the machine in line with the unit or at right angles to it. Table I covers the 1950 drill record at the mine, showing the types of machines used and the footage obtained. [ ] Development of the new units was prompted by a desire for solution of the following problems: 1-The ever-expanding operations within the Utah Pit, requiring some 65 miles of transmission pipe lines radiating from a central compressed air plant, have now taxed this compressor plant beyond capacity. While 100 lb per sq in. pressure is maintained at compressors, transmission losses from innumerable small leaks result in low terminal pressure at the drills. Fig. 1 illustrates that while terminal pressure varies according to size of air hose and fittings used, the average drill is operating on air pressures within the 60 to 70-lb range. The compressor plant is operated primarily for air rock drills. All drilling is done on day shift, but it is necessary to run two of the three 3720 cu ft capacity compressors during night shift in order to prevent drastic loss of pressure through leaks. On day shift all three compressor units are operated at capacity, so that there is no reserve safeguard available for extensive repairs to any compressor. The calculated volume of compressed air required for operation of 25 drills is but 33 pet of three day-shift compressors. While compressed air is being used to a minor extent for purposes other than drilling, it is felt that satisfactory substitute facilities could be provided in the event that air lines were no longer available. 2-Drill performance has increased beyond the capacity of present 3 ½ -in. drifter machines. 3-The installation, maintenance, and moving of air lines in routine mining is a growing problem. The 2-in. level lines are placed outside electrification towers and must be moved to new location upon completion of each shovel cut. In addition to these moves it is often necessary to dismantle level lines so that excessive shovel spillage, or material covering track following a blast, can be pushed in the clear with bulldozers. Where level room is limited, it is often necessary to remove air lines in giving bulldozers room to prepare grades for wagon drills. In spite of precautions taken, many level lines become buried, twisted, and constricted, with excessive air loss resulting. Excessive back break in blasting often leaves several sections of air line suspended in mid-air. Occasionally air lines come in contact with defective electric transmission towers, so that holes are burned through pipe. 4-Rail-handling of drilling equipment such as wagon drills from one location to another requires considerable locomotive crane crew time. Any new unit developed should travel under its own power. 5-Present practice requires accessory material including hose, water pressure tanks, water barrels, drill steel, and bits to be transported by means of push cars when drill locations are changed on any level. 6-In order to supply numerous drill locations with material, many stock piles of new drill rods, drill bits, and other essentials must be left at strategic points, usually in the vicinity of powder magazines. This practice makes for poor housekeeping and contributes to the loss of supplies. Planning the Unit It was felt that a mobile drill unit which would rectify the foregoing problems should meet certain demands: 1-It must furnish compressed air to operate a 4-in. rock drill at a pressure of 90 to 100 lb.

Jan 1, 1952

By W. Gundaker, F. C. Schwerer

Natural chromium-bearing spinels (chromites), which are used as refractory materials in basic steelmaking, are the only commercially important chromium ore and are also encountered as difficult-to-separate contaminants in ore deposits of potential economic value. Techniques for characterization and separation of ore materials frequently are dependent on the magnetic properties of the constituent minerals. An experimental program was initiated to explore the effects of temperature and of simple mechanical and thermal treatments on the static magnetic properties of several ore-grade natural chromites. Studies of the temperature dependence of the magnetic properties showed that the natural chromites, which are dilute in the magnetic ions Fe and Cr, order magnetically only at cryogenic temperatures. However, mechanical treatment in the form of crushing produces a magnetic component that is ordered at room temperature and that is of sufficient strength to alter magnetic-separation characteristics. The additional magnetic component apparently is associated with surface structures which develop during crushing and disappear after heating to above about 500°C. Preliminary studies indicate that this surface structure enhances the susceptibility of the chromite grain surfaces to gas reactions at moderate temperatures.

Jan 1, 1976

By R. I. Jaffee, H. R. Ogden, D. J. Maykuth

IN THE past year, Jaffee and Campbell&apos; and Finlay and Snyder2 reported on the mechanical properties of titanium-base alloys, some of which were in the same ranges of composition as are covered in this paper. In this paper, evidence confirming that given by Finlay and Snyder on the effects of carbon, oxygen, and nitrogen on titanium will be presented; and, in addition, new data will be given on the effects of these elements on the flow properties and phase transformation of titanium. Materials and Preparation of Alloys The preparation and general properties of iodide titanium have been adequately described elsewhere.&apos; , As-deposited iodide titanium rod, prepared at Battelle, of Vickers hardness less than 90 was employed as the base metal in the present work. This was the same material as that used by Finlay and Snyder.2 The probable analysis reported by them for standard quality metal holds here also: N 0.005 pct, 0 0.01 pct, C 0.03 pct, Fe <0.04 pct, A1 <0.05 pct, Si <0.03 pct, and Ti 99.85 pct. Carbon was added in the form of flake graphite supplied by the Joseph Dixon Crucible Co. Oxygen was added in the form of c.p. grade TiO, powder, produced by J. T. Baker Chemical Co. Nitrogen was added in Ti3N4 powder, supplied by the Remington Arms Co. Individual ingots weighed 7 or 8 g. Carbon, oxygen, or nitrogen was added by placing the corresponding powder in a capsule made from as-deposited iodide titanium rods and melting the capsule with the balance of the charge. The charge was are-melted with a tungsten electrode on a water-cooled copper hearth under a partial vacuum of very pure argon (99.92 pct minimum). Melting was practically contamination free. Vick-ers hardness increases of less than 10 points were normal for unalloyed iodide titanium control melts. Nitrogen analyses of are-melted iodide titanium showed a nitrogen content of 0.005 pct, about the same as is present in the as-deposited rod. No tungsten pickup was found in a melt of iodide titanium analyzed for tungsten. Weight losses in melting nitrogen-free alloys were very small and varied consistently from nil to 0.015 g (0 to 0.2 pct). This permitted the use of nominal composition for these alloys. Chemical analyses made for carbon, which can be analyzed conveniently by combustion methods, justified this procedure. Where nitrogen was added, considerable splattering took place. Here it was necessary to analyze for nitrogen by the Kjeldahl method. The ingots were hot rolled at 850°C to about 0.045 in. thick. After hot rolling, the strips were descaled by mechanical grinding, and then given a cold reduction of 5 to 10 pct to insure a uniform thickness throughout the length of the specimen. The edge strips and the tensile strips were annealed in a vacuum of 1x10-4 mm Hg pressure for 3 1/2 hr at 850°C and furnace cooled. Methods of Investigation Hardness Measurements: At least five Vickers hardness measurements were taken using a 10-kg load on each sample in the following conditions: (1) top and bottom of each ingot, (2) top and bottom surface of as-rolled and annealed sheet, and (3) on cross-section of annealed sheet and all quenched specimens. Tensile Tests: Tensile tests were conducted on Baldwin-Southwark testing machines having load ranges of 600 or 2000 lb. Tests were made on 1-in. gauge-length specimens, 3 1/4-in. overall length, 1/2 in. wide, 0.040 in. thick, with a reduced section 1 1/4 in. long and 0.250 in. wide. Two SR-4, A-7 strain gauges, one mounted on each side of the specimen, were used to measure the strain over a limited range to determine the modulus of elasticity. After the modulus of elasticity readings had been taken, load vs. strain readings were taken, using only one strain gauge, at increments of 0.0001 in. until the yield points were passed and then at 0.001-in. increments to the limit of the strain-gauge indicator (0.02 in.). Strain readings above 0.02 in. per in. were taken every 0.01 in., using dividers to measure the strain between the 1-in. gauge marks until the maximum load had been reached. Crosshead speed, when using the SR-4 gauges, was 0.005 in. per min, and, when using dividers, 0.01 in. per min. Flow Curves: Flow curves were determined using the true stress-true strain data obtained during the tension test. The usefulness of this type of information has been dealt with very adequately elsewhere by L. R. Jackson,&apos; J. H. Hollomon,6 and many others. Flow curves of true stress vs. true strain could be converted to the more conventional cold-work curve of 0.2 pct offset yield strength vs. percentage of cold reduction by means of the transformation, 1/1 = 1/1-R, where R is the fraction reduction in cold working. Thus, the true strains corresponding to percentage reduction can be calculated, and the 0.2 pct offset yield strengths scaled off the — 6 curve by taking the true stresses corresponding to the values of 6 + 0.002 strain. Heat Treatment: For the transformation studies, the alloys were heat treated in a horizontal-tube furnace using a dried 99.92 pct argon atmosphere, and quenched into water. Essentially no contamination was found after several hours of heat treatment at temperatures up to 1050°C. Metallography: Specimens were prepared in the

Jan 1, 1951

By H. M. St. John

THE melting department is the heart of the foundry. From it clean metal flows to the molding floor, in the right quantity, at the right time and at a sufficiently low cost-or, if not, the foundry fails to thrive. Since it is our purpose here to discuss present-day melting practice in the foundry, it may be well at the start to emphasize the wide differences in foundries and the conditions under which they must operate in order to reach the goal stated in the first paragraph. In every foundry, large or small, jobbing or captive, the same factors must be dealt with but they are of varying consequence and must be dealt with in varying ways in different foundries. Particularly in the nonferrous industry, there is so wide a variation in the composition of alloys used and in the character of castings made that no one type of furnace, nor any one method of operation, can be expected to produce the best results at all times. The present discussion will not attempt to include all nonferrous metals. It is intended to cover only the copper-base alloys in which copper is the dominant element, most of which are commonly known as brass or bronze. The discussion is further limited to the melting of these copper-base alloys for use in sand-casting foundries. Die-casting plants, the brass-rolling mills and certain other metal industries have melting problems peculiar to those industries, which will not be considered here. The following considerations are elemental in all foundries and are listed in what is believed to be the relative order of their present-day importance: I. The melting department must meet the foundry&apos;s requirement for dean, fluid metal, of specified composition and purity, at a temperature suitable for the work the foundry has in hand. This is the prime consideration in any foundry, at any time, anywhere. 2. Working conditions surrounding the melting furnaces and attending their use must be good. 3. The cost of molten metal at the mold must be as low as possible. 4. The operating characteristics of the furnaces must be sufficiently flexible, to meet normal variations in foundry requirements. 5. The operation and maintenance of the melting equipment must not require more skill and experience than is available in the particular foundry in question. METAL QUALITY It is not a function of the melting furnace to refine or improve the quality of the metal but simply to melt it without impairing its quality. Good practice requires, therefore, that care must be taken to supply the melting department with metal of inherently good quality, assured by specification or otherwise, having all the properties necessary to produce the castings desired. An alloy contains a number of primary elements, which must be present in definite proportions if the castings made from it are to have the desired properties. If the castings are made to a customer&apos;s specification, this will state the range within which these principal elements (for example, copper, tin, lead and zinc) are permitted to vary.

Jan 1, 1946

By G. W. Josephson

VIRTUALLY every year inventors find one or more startling new uses for one of the varied products of the nonmetallic mineral industries. For example, in November a major step toward positive control of rainfall was made when an experimenter converted a cloud to snow by dropping a few pounds of solid carbon dioxide into it. Other examples of ingenuity in the development of markets and production methods are noted in the following pages. For most of the industrial mineral products one of the outstanding features of 1946 has been the high level of production. There are exceptions, such as quartz crystal and lithium, whose production capacity during the war outgrew current peacetime needs, but they are few. Some technical men point out that this prosperity is not an unmixed blessing to technologic progress, because so much effort must go into day-to-day production problems that relatively little opportunity is left for the pursuit of new developments.

Jan 1, 1947

By Frederic H. Wright

The secondary metals industry might well be defined as the group of remelters, smelters, refiners, and manufacturers that convert scrap metals or residues to commercial forms. In this industry, scrap metals and residues are processed to pro- duce refined metals, ingot alloys, fabricated shapes, and chemical products. Secondary metal is defined as metal recovered from commercial scrap, that is, scrap that has entered the processor&apos;s plant in scrap form. Metal recovered by a manufacturer from "home scrap" generated in his own plant is not considered to be secondary, because it represents part of the original stock that simply requires additional treatment before emerging as a finished product. In any economic study, a basic point of measurement must be chosen, and in the case of secondary metals, the melting pot or its counterpart represents the stage in which metal is converted from scrap to some more usable form. Beyond this point there is often no means to distinguish between secondary metal recovered from scrap and virgin metal produced directly from ore. In the last fifteen or twenty years the secondary metals industry has grown to major importance. Some consumers distrust secondary metals, but frequently this distrust serves only to prove an inability to keep up with the times. A rapidly decreasing number of manufacturers like to boast that they use only virgin metals, but a little investigation would show them that more than one third of all

Jan 1, 1943

By J. L. Gillson

Historically, rock deposits and sand deposits of titanium minerals came into production about the same time, although there may be some argument as to what is meant by production. Beach de- posits of heavy minerals in India (Figs. 1-4) and Brazil (Figs. 5) were worked for monazite about the turn of century, but as there was then no market for titanium minerals, these were thrown away. The rock rutile deposits at Roseland, Va., Fig. 6, were worked to supply rutile for titanium chemicals and for coloring ceramics long before there was a titanium pigment business. The pigment industry started about the middle twenties, both in Europe and the U. S., and almost simultaneously the rock deposits at Ponte Vedra Beach near Jacksonville, Fla., were worked for titanium content. Since those days, production from both types of deposits has continued to grow at a rapid rate; many deposits of both types have been found, and reserves have grown to very large figures. In total tonnage of reserves, there is no doubt that the rock deposits are far ahead of the sand deposits; nevertheless there is a very large tonnage of commercial sands available. It is the quality of titanium mineral in the sand and the relatively lower costs of operating sand deposits that have kept them abreast, at least in annual tonnage produced, with the rock deposits.

Jan 4, 1959

By R. S. Dean

BLUE HEAT PHENOMENA IN constructing a theory of the flow and hardening of metals, we necessarily make use of such phenomena as seem to be, universally observed in metals. It is, therefore, a matter of. concern to the constructors of such mnemonic systems if one or two of the group classified as metals show anomalous behavior. Such egregious phenomena are observed in pure or nearly-pure iron in the reaction of its mechanical properties to low-temperature annealing after cold work and to increased temperature of testing. In short it has been generally observed that iron," as an outstanding exception among metals, increases its hardness and strength by low-temperature annealing. after cold work,1 and also by increase of testing temperature to the range of 150° to 300° C. The investigation here recorded was made then with the object of ascertaining if similar phenomena were observed in high purity iron and, if not, to the presence of which impurities these phenomena could be traced.

Jan 1, 1929

By R. H. Ogburn

THE GROUND now being worked by the Fairbanks Exploration Co., near Fairbanks, Alaska, has been known to be gold bearing since 1901. In the early days it was worked by drift mining and other small-scale methods. In 1922, Hammond started prospecting the gold-bearing ground and obtaining options on the properties desired. Two years later the present Fairbanks Exploration Co. started taking up the options, and preparing to exploit the ground. For the prospect drilling Keystone drills were used, with holes at the points of equilateral triangles 600 ft. apart. Holes were also put down more closely spaced to determine the limits of dredging ground. In the first drilling casing was used to the bottom of the holes, but in later work the casing was put down only to the bottom of the thawed ground, and the rest of the hole put down without casing. The gold content was determined by panning, each 2 ft. of depth being determined separately. Where no casing was used the size of the hole was determined by using water to measure its volume. The greatest concentration of gold occurs at or near bedrock. All the gold-bearing streams head in one big dome. Gold, however, is not found clear to the head of the creeks, the pay being first found some distance downstream from the head.

Jan 1, 1933

By Raymond Ward

Jan 1, 1945

By Harrison Schmidt

Since the U. S. Geological Survey published the data on the Central Mining District collected by Lindgren and Gratonl and by Paige2 much new information has been obtained by development and mapping, but none of it had been published until recently when Kniffin3 published on Fierro, Lasky4 on the Ground Hog mine, Thorne5 on Santa Rita and Landon6 filed a thesis on the Fierro-Hanover-Santa Rita area at the University of Chicago. During the years 1927-1930 much of the writer&apos;s time was spent in mapping the geology and ore deposits of this district, particularly in the area of the zinc deposits at Hanover. Some of the data collected are presented here. Previous publications have been freely drawn upon and additional data used that were generously supplied by L. M. Kniffin, Wilfred Wright and Gerald Ballmer. Thanks are due Augustus Locke, Samuel G. Lasky, Kniffin, Wright and Ballmer for suggestions and critical readings of the manuscript, and to the Empire Zinc Co. (a subsidiary of the New Jersey Zinc Co.) for the privilege of publishing material compiled largely at its expense. The relation of the Central or the Santa Rita-Hanover-Fierro district to the Silver City district is shown on Paige&apos;s geologic map in the Silver City folio.7 Granodiorite porphyry and quartz-monzonite porphyry

Jan 1, 1935

By Harrison Schmidt

Since the U. S. Geological Survey published the data on the Central Mining District collected by Lindgren and Gratonl and by Paige2 much new information has been obtained by development and mapping, but none of it had been published until recently when Kniffin3 published on Fierro, Lasky4 on the Ground Hog mine, Thorne5 on Santa Rita and Landon6 filed a thesis on the Fierro-Hanover-Santa Rita area at the University of Chicago. During the years 1927-1930 much of the writer&apos;s time was spent in mapping the geology and ore deposits of this district, particularly in the area of the zinc deposits at Hanover. Some of the data collected are presented here. Previous publications have been freely drawn upon and additional data used that were generously supplied by L. M. Kniffin, Wilfred Wright and Gerald Ballmer. Thanks are due Augustus Locke, Samuel G. Lasky, Kniffin, Wright and Ballmer for suggestions and critical readings of the manuscript, and to the Empire Zinc Co. (a subsidiary of the New Jersey Zinc Co.) for the privilege of publishing material compiled largely at its expense. The relation of the Central or the Santa Rita-Hanover-Fierro district to the Silver City district is shown on Paige&apos;s geologic map in the Silver City folio.7 Granodiorite porphyry and quartz-monzonite porphyry

Jan 1, 1935

Since the U. S. Geological Survey published the data on the Central Mining District collected by Lindgren and Gratonl and by Paige2 much new information has been obtained by development and mapping, but none of it had been published until recently when Kniffin3 published on Fierro, Lasky4 on the Ground Hog mine, Thorne5 on Santa Rita and Landon6 filed a thesis on the Fierro-Hanover-Santa Rita area at the University of Chicago. During the years 1927-1930 much of the writer&apos;s time was spent in mapping the geology and ore deposits of this district, particularly in the area of the zinc deposits at Hanover. Some of the data collected are presented here. Previous publications have been freely drawn upon and additional data used that were generously supplied by L. M. Kniffin, Wilfred Wright and Gerald Ballmer. Thanks are due Augustus Locke, Samuel G. Lasky, Kniffin, Wright and Ballmer for suggestions and critical readings of the manuscript, and to the Empire Zinc Co. (a subsidiary of the New Jersey Zinc Co.) for the privilege of publishing material compiled largely at its expense. The relation of the Central or the Santa Rita-Hanover-Fierro district to the Silver City district is shown on Paige&apos;s geologic map in the Silver City folio.7 Granodiorite porphyry and quartz-monzonite porphyry

Jan 1, 1935

By Harrison Schmidt

Since the U. S. Geological Survey published the data on the Central Mining District collected by Lindgren and Gratonl and by Paige2 much new information has been obtained by development and mapping, but none of it had been published until recently when Kniffin3 published on Fierro, Lasky4 on the Ground Hog mine, Thorne5 on Santa Rita and Landon6 filed a thesis on the Fierro-Hanover-Santa Rita area at the University of Chicago. During the years 1927-1930 much of the writer&apos;s time was spent in mapping the geology and ore deposits of this district, particularly in the area of the zinc deposits at Hanover. Some of the data collected are presented here. Previous publications have been freely drawn upon and additional data used that were generously supplied by L. M. Kniffin, Wilfred Wright and Gerald Ballmer. Thanks are due Augustus Locke, Samuel G. Lasky, Kniffin, Wright and Ballmer for suggestions and critical readings of the manuscript, and to the Empire Zinc Co. (a subsidiary of the New Jersey Zinc Co.) for the privilege of publishing material compiled largely at its expense. The relation of the Central or the Santa Rita-Hanover-Fierro district to the Silver City district is shown on Paige&apos;s geologic map in the Silver City folio.7 Granodiorite porphyry and quartz-monzonite porphyry

Jan 1, 1935

Jan 1, 1957

By A. E. Dwight, Paul A. Beck

Known CsCl-type phases in transition metal alloys are shown to be formed preferentially at an electron concentration of approximately 6; a tetragonally distorted version of the CsCl structure is stable at -e/a = 6.5. The relationship of the distortion to electron concentration is verified by experimental data for the quasibinary systems Time ,Os) , Ti(Re,Ir), and Ti(Re,Pt) and the ternary system Ti-Ru-Rh. It was noted some years ago1j2 that the occurrence of CsC1-type ordered structures in equiatomic binary alloys, AB, of transition metals correlates with the location of the component elements in the periodic table. One of the components, A, must be to the left and the other component. B, must be to the right of the chromium group. It was pointed out2 that the CsCl structure does not occur in CrFe. is metastable in VFe,3 and is stable in TiFe up to high temperatures, and that this progressively increasing stability may correspond to an increase in electron transfer between the two components and to a correlated decrease of the magnetic moment associated with the iron atoms. Such a decrease was in fact later demonstrated by Nevitt. 4 The binary CsC1-type phases that are formed by a transition metal with either another transition metal or a lanthanide are listed in Table I. Thirty-three of these phases occur at an average electron concentration (average number of electrons outside of closed shells) of e/a = 6. The five phases that are formed at an electron concentration of e/a = 5.5 appear to be borderline cases. This is suggested for instance by the fact that TiRe is bcc. without any long-range order, while TiTc (at the same electron concentration) has a CsCl ordered structure. Six of the undistorted CsCl phases formed by transition metals with one another have an average electron concentration of e/a = 6. 5. Table I. With the exception of Zr4,Rhs4 and Hf48Rh52. the B component in these phases is a first long-period transition metal, i.e.. iron or cobalt. TiNi. with an electron concentration of e/n = 7, appears to undergo transformation at around room temperature to a more complex ordered struct~re.~ The five other CsCl structures known to occur at e/a = 6.5 have either scandium or a lanthanide metal as the A component; the difference in the elec-tronegativity and in the e/a ratio between the component elements is in these phases very large, A(e/a) - 7, and they may be expected to have a rather strong ionic bond component. Presumably the ionic bond stabilizes the CsCl-type structure at the equiatomic composition and it overrides the electron concentration requirement. When the B element is not from the first long period and the A component is not a rare earth metal. equiatomic (AB) alloys of transition metals with an average electron concentration of e/a = 6.5 in most cases have a crystal structure closely related to the CsC1-type, but slightly distorted tetragonally, Table I. This was first found6 for VRu, NbRu. and TaRu. It was noted6 that the undistorted CsCl structure is also stable in the three systems. but at a lower electron concentration, near e/a = 6. In these systems this requires a deviation from equiatomic stoichiometry. which is otherwise ideally suited for the CsC1-type structure. A similar situation was later found in the Ti-Rh7 and the Ti-Ir systems. 8 The Ti-Rh alloys undergo a second distortion and become orthorhombic when the rhodium content becomes somewhat larger than 50 pct. As mentioned previously. TiRe does not have the CsC1-type ordered structure. In order to investigate how close TiRe is to the borderline of stability of the

Jan 1, 1970