Search Documents

A shrinkage stope is an overhand stope in which the broken ore accumulates until the stope is completed to, or near, the level above. As broken ore generally occupies at least 60 per cent. more space than ore in place, about a third of this must be drawn out as the stope advances to leave a working space under the back. The ore remaining supports the miners and gives temporary support to walls, and is all withdrawn when the stope is finished. The shrinkage-stope method is applicable to steep-dipping deposits of strong ore with strong walls. It may be applied to narrow or wide veins, and is simple and cheap. Five examples, which include important and varied types of deposits, are given: namely, Kennecott, Homestake, Jarbidge district, Mogollon district, and Cripple Creek district.

Jan 1, 1925

Utah Engineering Experiment Station, University of Utah, Salt Lake City, Utah. D. A Lyon, Director. Important work on ore dressing has been carried out at this station Before listing the Technical Papers and Bulletins available, it is well to point out especially that Technical Paper 1, Flotation fundamentals, 4, Flotation fundamentals (pt 2), and 5, Flotation fundamentals, pt 3, are out of print and can only be consulted at libraries or elsewhere. The Technical Papers and Bulletins available are as follows: Technical Paper 6, Recovery of zinc from ferrite compounds in the electrolytic zinc process, 25 cents; 7, Flotation fundamentals (pt 4), 40 cents; 8, The technique of preparing thin sections of rock, 75 cents; 9, Flotation fundamentals (pt. 5) 30 cents; 10, A new development in the preparation of briquetted mineral grains, 15 cents, 12, A method for the determination of cadmium in mill and smelter products, 25 cents; Bulletin 10 (revised 1931), Mine sampling and the commercial value of ores, 35 cents, 14, Report of research investigations (1922-23), with papers on these subjects Hydrometallurgy of zinc, Flotation experiments on Utah sulphur ore, Oil shale investigations, Zinc oxide investigations, 25 cents;

Jan 1, 1933

By J. E. Steiner, J. M. Hodge, M. A. Orehoski

Ingots of four steels (1045, 1080, Ni-Mo-V, and Ni-Cr-Mo-V) were cast at pressures varying from about 1 to 760 mm of mercury, so as to obtain a range of hydrogen contents in each steel. The susceptibility of these steels to flaking was evaluated by cooling hot-rolled blooms at a range of cooling rates, varying from water quenching to slag cooling, and studying the occurrence of flaking as a function of cooling rate. The steels exhibited differences in susceptibility to flaking, and a tlzreshold value for hydrogen content for each steel was found, below which the susceptibility was very low and above which the susceptibility increased markedly with increasing hydrogen content. Mechanical property evaluations, metallogvaplzic exantinations, and X-my diffraction determinations o,t retained austenite were made on samples from the blooms. A mechanism of flaking which is consistent with the observed behaviors, the effects of hvdrogen content, and the differences in susceptibility among the steels investigated is postulated, based on the results of mechanical property evaluations and metallographic and X-ray diffraction studies. ThE important role of hydrogen as a factor in the occurrence of "flakes" or "hair-line cracks" in steel has now been established by many investigations. These have included investigations by steel producers and forging manufacturers, to whom the prevention of flaking is a very real and serious problem, and many research studies aimed primarily at establishing the mechanism of this behavior Several investigators3 have reported that steels cast at reduced pressures (absolute pressures of about 1 mm) not only are low in hydrogen content but are essentially insensitive to the formation of flakes. These investigations have shown that a general relationship exists between hydrogen content and susceptibility to flaking. The difficulty of obtaining suitable samples of steels of a given composition with the desired range of hydrogen contents, particularly in the relatively large sections in which flaking most commonly occurs, has been the principal obstacle to quantitative evaluations of these relationships. Steels with intermediate hydrogen contents between 1 ppm, and the 4ppm or higher of air-cast steels are generally not available in commercially produced steels. Laboratory procedures, in which the hydrogen is introduced into solid steel samples by heating in a hydrogen atmosphere under pressure, generally involve a limitation in the size of the sample which can be treated, and thus are not representative of the behaviors in large sections. The availability of a facility at the South Chicago Works of U.S. Steel, in which several ingots could be cast from a single heat of steel at total air pressures ranging from 0.25 to 760 mm of Hg, has made it possible to overcome this obstacle and to obtain ingots of a given steel covering the intermediate range of hydrogen contents desired. These ingots, furthermore, are of a size suitable for the production of product with section sizes large enough to be representative of the products in which flaking most commonly occurs in commercial production. In these experiments, this facility was used to study the relationships between hydrogen content and the susceptibility to flaking of four steels, two plain carbon steels at 0.45 and 0.80 pct C and two low-carbon alloy steels representing a medium and a rather high hardenability level. These flaking studies were supplemented by evaluations of mechanical properties and by metallographic studies on samples from the blooms, in order to obtain pertinent information on the factors other than hydrogen content which influence the susceptibilities of these steels to flaking. Based on the results of these tests, a mechanism for the initiation and propagation of the flaking cracks, which is consistent with the observed behaviors, is postulated. MATERIALS AND EXPERIMENTAL WORK Steelmaking and Conversion. To provide material for the investigation, five 29- by 35-in., hot-topped, big-end-up ingots were cast from each of four 80-ton, basic electric-furnace heats of four different steels (a 1045 steel, a 1080 steel, a Ni-Mo-V steel, and a Ni-Cr-Mo-V steel). A double-slag practice was used on all steels and the two plain carbon steels were Si-A1 deoxidized with an addition of 2 lb of A1 per ton, while the Ni-Mo-V and Ni-Cr-Mo-V steels were deoxidized only with silicon and

Jan 1, 1964

By Robert McKay

THE practical study of corrosion requires consideration off its economic aspects. It must be based on sound scientific principles, but it should be borne in mind that probably the most important object of a corrosion test is to determine what metal in corrosion-resisting construction will produce the greatest operating profit. Thus the corrosion test must be directly connected with money values or it is not a practical corrosion test. This, perhaps unusual, connection between corrosion and economics is partially due to the fact that corrosion deals only with the time factor or duration of equipment, and it is almost the only test which deals with this feature. In these statements a departure is made from the academic definition of the word corrosion and it is done deliberately. The use of the term corrosion is unusual. It is as though we spoke of a tensile test as. a "breaking" test. We are not interested primarily in the break but in the strength of the metal. There is no English word which expresses our main interest in corrosion-testing, but let us have clearly in mind that we make corrosion tests to prevent corrosion. Our real interest is in this corrosion-prevention, not in the corrosion. Previous to 1922, it was common comment that "it is impossible to determine the course of corrosion by laboratory testing." This statement was true at that time in that the technique of laboratory testing for corrosion resistance was so vague that tests in the laboratory gave untrue results almost as often as true ones. This was so, even in the simple case of determining which one of two metals better resists a given solution. While this is no longer true the number of misleading "corrosion tests" still being ground out by laboratories is too large in the light of our present knowledge. There are two important features of corrosion testing whose neglect is a large contributing factor to misleading results: (1) The economic relations of the corrosion tests to other tests; (2) testing technique.

Jan 1, 1929

[NORTH AMERICA UNITED STATES ALABAMA ADAMSVILLE U. S. Steel Corp. Neason, James E. ALBERTVILLE Thompson Floral Co. Loudermilk, E. L. ANNISTON No Data Supplied Bonnichsen, Bill BESSEMER U. S. Steel Corp.-TCI Div. Beck, Adolph W., Jr. Boyle, James R. Cofield, William H. *Evans, James D. F., II *Guyton, Jesse C. Johnson, Leland H. Tetley, Albert L. No Data Supplied Crockard, F. H. Fisher, Joe T. Griffin, Joseph M. McFarland, E. A. Mohr, Henry E. Neal, George M. Walker, Wilber D.]

Jan 1, 1961

By V.K. Zworykin

Throughout its development the science of electronics, like so many other branches of science and industry, has been indebted to the metallurgist. Metallurgy has provided the electronic engineer with conductors to furnish passage for electrons outside of his evacuated tubes: it has developed tungsten and tantalum wires for emitting electrons and various refractory metals and alloys suitable for electrodes, which receive them and guide them within the tube; finally it has supplied ferromagnetic materials both for shielding electronic apparatus from magnetic fields and for forming highly concentrated fields for deflecting electron . Today I hope to show you that electronics has not been altogether ungrateful for this assistance. More specifically, I wish to indicate the role that the electron microscope, a relatively recent product of electronic engineering, is playing even now in the study of metals. Every metallographer is aware that his standard metallographic microscope will not reveal structural detail involving separations smaller than a certain fraction —at the very best a tenth—of a micron. This limitation, he knows, is a consequence of the fact that the wave length of the light employed for forming the image has this order of magnitude. It is, thus, a property of all light microscopes. TO overcome it, a different imaging medium must be employed, The existence of such a medium became evident when it was demonstrated1 that electrons were affected by magnetic and electric fields with axial symmetry just as light is affected by glass lenses; these fields, or "electron lenses," curve the paths of electrons reaching them from an object located on the axis of symmetry in such a manner that, at some distance from the lens, a true image of the object is formed. Furthermore, although a wave length may . be ascribed to electron beams just as to light, this wave length is much shorter; for electrons accelerated through a difference of potential of 50 kilovolts, the wave length is only about one hundred-thousandth of that of visible light. Actually, the elcctron microscopes of today resolve detail one hundred times as fine as light microscopes; if the maximum useful magnification of the latter is taken to be a thousand, that of electron microscopes is one hundred thousand. The Electron Microscope Since electrons are readily scattered and absorbed by matter, specimens to be observed in the electron microscope must be prepared to be less than one micron in thickness; furthermore, the interior of the microscope must be carefully evacuated to prevent collisions between the clectrons and the molecules of the air. Finally, as already mentioned, the lenses are formed by axially symmetric magnetic or electric fields, and not by any material medium such as glass. Apart from these basic differences, the electron microscope closely

Jan 1, 1943

By V. K. Zworykin

Throughout its development the science of electronics, like so many other branches of science and industry, has been indebted to the metallurgist. Metallurgy has provided the electronic engineer with conductors to furnish passage for electrons outside of his evacuated tubes: it has developed tungsten and tantalum wires for emitting electrons and various refractory metals and alloys suitable for electrodes, which receive them and guide them within the tube; finally it has supplied ferromagnetic materials both for shielding electronic apparatus from magnetic fields and for forming highly concentrated fields for deflecting electron . Today I hope to show you that electronics has not been altogether ungrateful for this assistance. More specifically, I wish to indicate the role that the electron microscope, a relatively recent product of electronic engineering, is playing even now in the study of metals. Every metallographer is aware that his standard metallographic microscope will not reveal structural detail involving separations smaller than a certain fraction —at the very best a tenth—of a micron. This limitation, he knows, is a consequence of the fact that the wave length of the light employed for forming the image has this order of magnitude. It is, thus, a property of all light microscopes. TO overcome it, a different imaging medium must be employed, The existence of such a medium became evident when it was demonstrated1 that electrons were affected by magnetic and electric fields with axial symmetry just as light is affected by glass lenses; these fields, or "electron lenses," curve the paths of electrons reaching them from an object located on the axis of symmetry in such a manner that, at some distance from the lens, a true image of the object is formed. Furthermore, although a wave length may . be ascribed to electron beams just as to light, this wave length is much shorter; for electrons accelerated through a difference of potential of 50 kilovolts, the wave length is only about one hundred-thousandth of that of visible light. Actually, the elcctron microscopes of today resolve detail one hundred times as fine as light microscopes; if the maximum useful magnification of the latter is taken to be a thousand, that of electron microscopes is one hundred thousand. The Electron Microscope Since electrons are readily scattered and absorbed by matter, specimens to be observed in the electron microscope must be prepared to be less than one micron in thickness; furthermore, the interior of the microscope must be carefully evacuated to prevent collisions between the clectrons and the molecules of the air. Finally, as already mentioned, the lenses are formed by axially symmetric magnetic or electric fields, and not by any material medium such as glass. Apart from these basic differences, the electron microscope closely

Jan 1, 1943

By C. H. Mathewson

MICROSCOPIC rnetallography has been exploited quite well enough to bring about a very general understanding that the typical metal or alloy is composed of minute crystalline particles blended into a coherent microstructural mosaic. One does not have to be a specialist in metallography to realize that the properties of such an aggregate are essentially a summation in appropriate form of individual effects derived from the shape, size, placement or orientation and cohesive characteristics of the component particles. It is clearly of great importance to consider the various forms of discontinuity which may occur at the boundaries between these crystalline particles. When a number of particles each possessing the same orderly arrangement of atoms are brought together into a close-fitting system of purely haphazard contacts, not unlike a handful of snowflakes compacted into a snowball, the particles are said to possess random orientation. There are no generally accepted views concerning the arrangement of the atomis or the constitutional reaction between atoms where one crystal meets another, but these contact regions are characterized by strength rather than weakness and it is customary to require the presence of many rather than few boundaries in preparing metal for useful service. Under certain circumstances all of the particles in a metal may be nearly alike in orientation. Other general tendencies of orientation may be associated with particular forms of mechanical and thermal treatment. In contrast with these cases of fortuitous or statistical diversity of orientation, we often find adjacent particles united along a plane which possesses a grouping of atoms belonging equally well to both structures. This, of course, determines a fixed relationship between the two orientations and it is always possible to derive one from the other by some form of rotation or reflection prescribed by the symmetry of the crystal structure under consideration. Particles united in this manner are known as twin crystals although the term refers to the form of association rather than the number of individuals concerned.

By Henry Rawdon

THE RELATION between the course, or path, of the fracture of metals and alloys, produced in service or as a result of certain laboratory tests, and the crystalline units of which such materials are composed is of utmost importance. The fracture of normal material is, in general, intracrystalline, i.e., it consists of a break across the grains rather than of a separation between them. An intercrystalline fracture indicates either that the metal is of very inferior quality or that the break occurred under very unusual conditions, e.g., at a very high temperature. The usual mechanical tests, when applied to metals of the type that breaks with an intercrystalline fracture, merely measure the coherence of adjacent grains for one another and reveal little as to the real properties of the metal itself. Even such a soft plastic substance as lead, under suitable conditions, may be rendered so weak and brittle that the metal can be easily crumbled into powder by the fingers although the constituent grains have lost none of the intrinsic properties of lead. Various erroneous explanations of this behavior of lead have appeared in the scientific literature, the change being described usually as an allotropic one. The importance, in an industrial sense, of a proper explanation of this type of the corrosion of lead justifies the description of the type of metal deterioration that follows.

Jan 2, 1920

By S. Brunauer

The hydration of portland cement is treated as a chemical reaction and the changes in matter, in energy and the rate of change of the process are discussed, Portland cement is a mixture of four major and at least as many important minor constituents. In the hydration process, the four major compounds (trical-cium silicate, dicalcium silicate, tricalcium alumi-nate and tetracalcium aluminoferrite), plus gypsum and water form five or six new compounds. In spite o the great complexity of the reaction, considerable progress has been made in its understanding, primarily with the help of such research tools as X-ray diffraction and electron microscopy. The rate of the reaction can be followed by direct and indirect methods of measurements. The effects o composition, particle size (or specific surface), temperature and water-cement ratio on the rates of hydration are discussed. The hydration of portland cement is a chemical reaction accompanied by such highly important physical phenomena as heat evolution, setting and hardening. It is a vast and complex subject, on which hundreds of papers have been published. At the time of the writing of this paper, in October 1962, a two-volume book, which alone contains dozens of papers pertaining to cement hydration appeared in print.' The present paper deals with a few aspects of this vast subject, and the selection was not easy. The work reported here deals with some of the most recent investigations in the field. In any chemical reaction, the physical chemist is primarily interested in three things: changes in matter, changes in energy and the rate of change of the process or the speed of the reaction. This is true also of the chemical reaction between portland cement and water, and all three aspects of the reaction will be discussed. These three aspects are of vital interest to the engineer as well. Portland cement is not a cementing material — the hydration products, the new materials which form in the reaction, have the cementing action. The energy changes manifest themselves in a considerable evolution of heat, which may be useful or harmful. It is useful, for example, in winter concreting, but in very large concrete structures like dams, a large evolution of heat, which cannot be easily dissipated, may produce distress in the structure. Primarily for such a purpose was the Type IV or low heat portland cement developed. The speed of the chemical reaction is important because it determines the time of setting and hardening. The initial reaction must be slow enough to permit placing of the concrete before setting occurs. On the other hand, after the placing of concrete it is often highly desirable to obtain as rapid chemical reaction as possible. For this purpose the Type 111 or high early strength portland cement was developed. CHANGES IN MATTER Portland Cement: In a basic investigation, before one begins to study a reaction, one either knows the quantities and compositions of the starting materials, the reactants, or one determines them. This is obvious; the chemist expresses the changes in matter that occur in a reaction by a chemical equation, which has the quantities and compositions of the reactants on the left side of the equation and the quantities and compositions of the reaction products on the right side. The first question is then what to put on the left side of the equation in the reaction between portland cement and water? It is not very easy to answer this question. Portland cement is not a single chemical compound but a mixture of many compounds. Four of these are considered the major compounds, and at least four of the minor compounds also play important roles in the hydration reaction. In order to avoid complicating matters, the present discussion will be restricted primarily to the four major compounds, which constitute usually more than 90% of a portland cement. The relative amounts of these compounds vary from cement to cement. Actually not only the amounts but the compositions of these constituents also vary to some extent, but the variation in composition of the individual components will be neglected for simplicity.

Jan 1, 1963

By H. W. Morse

The experimental work on the oxidized copper ore at the New Cornelia mine at Ajo, Ariz., ended on Jan. 12, 1916. On that date final decision was made on the general nature of the process to be used in the 5,000-ton leaching plant, and on many of the details, as far as experience on a 40-ton scale could decide them. With the approval of the Board of Directors and the General Manager, John C. Greenway, we have compiled what seem to be the most interesting data on the results obtained during the experimental period. The most important part of the data resulted from the operation of a 1-ton and a 40-ton plant at Ajo. Experimental work on Cornelia oxidized ore dates back to April, 1912, and has been going on nearly continuously since that time. A good many variations from the original idea have been tried, but the process finally decided upon is in principle and in all of its details a simple one. The history of the leaching work on this ore has been brought down to about a year ago in papers presented to this Institute by Stuart Croasdalel and Dr. L. D. Ricketts.2 The present paper will, therefore, deal principally with the results obtained during the last year of the work. Preliminary Tests by Mb. Croasdale Preliminary tests were begun by Stuart Croasdale in July, 1912. A number of important points were definitely decided by his work. Among these were: 1. New Cornelia oxidized ore, not very finely crushed (to about 2-to 3-mesh) showed good extraction with 5 per cent. sulphuric acid. It appeared that better than 80 per cent. extraction could be expected. 2. The consumption of acid for this extraction was not prohibitive. It was apparently 3.5 to 4 1b. gross per pound of copper recovered.

Jan 1, 1917

By Robert J. Anderson

DURing the past 5 years no subject has aroused more interest or received more attention among mill operators than flotation. One reason for this is, undoubtedly, the remarkable success of the process in Australia where that country has risen to the position of furnishing one-fifth of the world's supply of zinc. The plant of the Butte & Superior Copper Co., designed by James M. Hyde in 1912, was the first important large flotation plant in this country; other installations have been made since then with considerable frequency, particularly so in the last 2 years. Without going into complete detail, it may be safely said that although flotation is a highly successful commercial process, it is more or less on an empirical basis. Upon scanning the literature, it is found that the flotation investigations have, in the main, dealt with a solution of the problems which accrue to practise; until recently no attempt was made to remove the difficulties in the way of the formulation of a consistent and harmonious theory. Of late this phase of the work has been receiving considerable attention, particularly by the United States Bureau of Mines at its Salt Lake City station, by the Mellon Institute at Pittsburgh, by the General Engineering Co. at Salt Lake City, by many of the mining schools, and private individuals almost ad infinitum. There is, at present, an enormous amount of laboratory work being carried on in flotation research, and probably the time is not far away when a generally acceptable explanation of flotation phenomena can be set forth. However, at this time, it seems as though the current technology is befogged with a superabundance of contradictory evidence; this confusion can only be dispelled as time proceeds and the knowledge of the subject becomes more complete. Many phenomena are supposed to contribute to the flotation of minerals, whether in whole or in part is a mooted question. I shall only sketch roughly the present tendency of ideas and make no reference to the first early and crude notions which have little value other than histori-

Jan 1, 1917

By David B. Brooks

INTRODUCTION Resources are not; they become (Zimmermann 100) . The companion concepts of reserves and resources appear, one way or another, in almost all considerations of mineral supply. Yet, no other concepts in the economics of the mineral industries have occasioned so much confusion. Whereas everyone agrees that in general the terms refer to the amounts of material that-depending upon technology, market conditions, and institutions-will become available for production in the near or more distant future, the apparent agreement disappears when we come to more specific definitions or to application of the definitions. Some definitions emphasize the physical aspects of reserves and resources, while others emphasize the economic. Some treat reserves and resources as fixed quantities, while others regard them as continually varying. Some consider that reserve and resource estimates have validity only for individual deposits, while others insist that they can be measured with sufficient accuracy for regional or national planning. This confusion in concepts that lies at the very heart of mineral economics is both strange and not so strange. It is common in the social sciences to find concepts that have been adopted into scientific jargon from popular usage and given rather special meanings -at the same time that they continue to be widely used without such qualifications. Psychologists have the same trouble with personality and sociologists, with community. Nevertheless, an attempt must be made to straighten out the various meanings of reserves and resources, or at least to clarify the conditions under which different meanings are applicable, before much progress in analysis of mineral problems can be expected. That is the objective of this chapter. Throughout the chapter, an attempt has been made to provide enough references to guide the interested reader to the most pertinent works on the concepts under study. However, even in a review article, it is no longer feasible to provide a comprehensive set of citations; there are simply too many. In many instances the works cited will themselves include the bibliographies needed to complete a literature search; those that are particularly useful in this respect are so noted. Also, because of the limited availability of foreign periodicals, some important works -originating largely in Canada, France, the

Jan 1, 1976

By John Wellington Finch

THE- impression which the public has of northern Canada is that it is a' vast wilderness of forests; river's, and. lakes, sparsely inhabited by. a few Indians and `containing a few, scattered trading posts of the Hudson Bay Co. This is far from the facts. The building of the Canadian Pacific Railway led to the discovery, in 1883, of the nickel deposits of Sudbury, Ont.; these are the largest known nickel deposits in the world and produce about 90 per cent. of the world's output of nickel. The building of the Temiskaming and Northern Ontario Railway north, from North Bay, to open up farming lands along Lake. Temiskaming, resulted in the discovery and development of the great silver deposits of the Cobalt area, Ontario. Since the discovery of these deposits in 1903 to Dec. 31, .1923, Cobalt has produced a total of ' 327,301,897 oz. of silver, valued at $212,668,434, and paid in. dividends $88,338,185. In 1923 the production of Cobalt amounted to 10,285,247 oz. of silver. Just south of Cobalt, in South Lorrain,. a. new silver district has recently been developed and mills have started production. These deposits are of such extent that 'a branch railroad is under construction from Cobalt to that area. Northwest of Cobalt is the Gowganda silver area which is also a producer of silver ore and is now attracting outside attention. This area is not connected by railroad.

Jan 1, 1924

By David C. Jonson, W. Bruce MacKenzie, Arthur A. Bookstrom, Vaughn E. Surface, Neil K. Muncaster, Stewart R. Wallace

In mid-Tertiary time a wet silici-alkalic magma penetrated the Precambrian rocks of what is now the Tenmile Range of Central Colorado and formed the Climax Stock. The stock is a composite one and was intruded in four separate irruptions, each giving rise to a major hydrothermal event. The first three of these produced large stockwork ore bodies that cap and flank the tops of their respective source intrusives; the fourth, and last, yielded almost no commercial mineralization. The ore bodies and their related zones of alteration are circular to ring-shaped in plan and arcuate in section. The different phases of the stock are so positioned with respect to each other that many of the circular and arcuate zones of mineralization and alteration overlap or are juxtaposed. Evidence of a time separation between the different ore bodies is found in certain dikes that were intruded between periods of mineralization and are well mineralized in one ore body but are barren in another. If it is assumed that the parent magma at Climax contained 10 per cent "water," that the "water" contained 0.1 grams per liter of molybdenum, and that the processes of extraction were 100 per cent efficient, then approximately 10 cubic miles of magma would be required for the formation of each ore body. The volume requirements, taken in conjunction with the cross-sectional areas of the different phases of the stock to explored depths, suggest to the authors that each magma chamber was columnar, extended to a depth of thousands of feet, and was connected with a much larger master reservoir. The repetition of similar intrusive, structural, and hydrothermal events, indicates periodic tapping of this reservoir. A regular chemical evolution of the parent magma is suggested by the systematic change in metal ratios and differences in the sites of deposition, relative to the source intrusive, in each of the four separate igneous hydrothermal stages. The preparation of ground was due to changes in magmatic and/ or hydrothermal pressures within the igneous-hydrothermal columns; small, repeated, up and down movements of the rock enclosing the tops of the columns formed the stockwork fractures into which the mineralizers penetrated. The forceful emplacement of each successive phase of the Climax Stock resulted in a slight doming and rotation to the westward of the earlier-formed geologic features. Postore normal displacement along the Mosquito fault is estimated at about 9000 feet. Part of one ore body was cut by the fault and lies at depth below the Paleozoic sedimentary strata on the hanging wall. On the footwall side of the fault, subaerial erosion and glaciation removed a large part of one ore body and uncovered the top of a second.

Jan 1, 1968

By P. Shahinian, H. H. Smith, M. R. Achter

Crack growth rates are measured at elevated temperature in a resonant fatigue machine from vibration frequency decreases calibrated in terms of crack depth. Crack growth rates in Type 316 stainless steel at 500º and 800°C show a sharp increase with oxygen pressure in an intermediate pressure range and little or no change at high and low pressures. At 500°c, I torr of oxygen reduces the fatigue life by almost a factor of 100 in comparison to that in vacuum and raises the growth rate of shallow cracks by the same At At 800°C the effects are smaller. Changes in slope in the crack growth rate curves are discussed in terms of a model in which rates of surface production and of surface coverage by gas are compared. The use of a calculation method in which the surface exposure time is equal to X/v, where x is the interatomic spacing and v is the growth rate, makes it possible to obtain order of magnitude agreement at 500°C between the observed pressure and the predicted pressure at these slope changes. At 800°C oxidation becomes a .factor and the data cannot be treated by simple adsorption theory. THE decrease in the fatigue life of metals as a function of gas pressure usually follows a stepped curve with virtually all of the decrease concentrated in a sharp drop in a transition zone at intermediate pressures and little or no change at low and high ranges. A number of models, differing in the details of the mechanism, have been offered to explain the shape of the curve. Measurements of crack growth in aluminum as a function of gas pressure by Bradshaw and Wheeler' and Hordon2 demonstrated opportunities for quantitative comparison to evaluate the proposed models. Since comparable data were lacking at high temperatures, in the present work rates of crack propagation were measured in Type 316 stainless steel at 500" and 800°C as a function of oxygen pressure. Choice of this material was dictated by two considerations; it is stiff enough at these elevated temperatures to resonate with the regenerative drive on our fatigue machine and it is known to display a large effect of environment. A new method of calculation is described to predict the gas pressure at the critical point. EXPERIMENTAL PROCEDURE Because of the difficulty of measuring crack depths directly at high temperatures, an indirect method was developed based on the decrease in the resonant frequency with the growth of a crack. A reversed bending, constant amplitude fatigue machine, described previously,3 vibrates a specimen at its resonant frequency, automatically records any changes in it and shuts itself off after it has reached a preset value of frequency decrease. The record of frequency change is used to determine the rate of crack growth. Sheet type specimens of Type 316 stainless steel, Fig. 1, incorporated a sharp, shallow notch to localize the formation of a single crack. After machining, they were annealed in a vacuum of l0-6 torr either at 1066" (lot A) or 871°C (lot B) and then electropolished in an acetic-chromic acid solution. Bending strains were measured at 500" and 800°C by an optical technique4 and reported as total strain without correction for the notch. At 500°C, the 0.141 pct strain was 0.085 pct elastic and the remainder plastic. At 800°C the 0.062 pct strain was all elastic. To convert frequency decrease to crack length, calibration curves were obtained by interrupting the vibration at stated intervals of frequency decrease. The crack depth was measured microscopically at a magnification of X400 and reported as the average of the measurement on each edge. Some specimens were sectioned for crack measurement while others were returned to the machine and fatigued further. There was good agreement between the two methods. Before beginning the vibration, the vacuum chamber was first evacuated cold to 1 x 1O-6 torr, then heated to the operating temperature and held there until the pressure was again reduced to 1 x10-6 torr at which time oxygen was introduced to the desired pressure. In this investigation the vibration frequency was nominally 10 cps and a decrease of 0.6 cps was taken as the failure point. The choice of the frequency decrease to represent failure has no appreciable effect on the fatigue life because the crack is growing very fast at this point.

Jan 1, 1970

By William Greenawalt

The Greenawalt electrolytic copper extraction process is applicable to suitable oxide ores, sulfide ores and concentrates, and low-grade matte. The process is self-sustaining in acid on sulfide ores or concentrates, on mixed ores, on high-grade oxidized ores; and on low-grade oxidized ores the amount of acid to be purchased or manufactured is greatly reduced. The ferric iron is under easy control, and copper may be effectively deposited from solutions of any acid or iron content likely to be used in copper leaching. From 60 to 75 per cent. of the copper may be removed from the solution in passing through the electrolytic department, before returning the solution to the ore. The amount of copper requiring chemical precipitation, from the waste and foul solutions, is only about 5.0 per cent, of the total copper produced, and this 5.0 per cent. is converted into the electrolytic metal in the regular operation of the process. The entire process can be made practically automatic, and can be carried out mechanically. There is no uncertain departure of any kind in the application of the process; no unusual or unproved apparatus is used. EVER since electrolytic copper refining gave promise of success, about a half century ago, efforts have been made to apply the idea to the extraction of copper from its ores. The methods of attack have, usually, been to leach with a dilute acid and then to deposit electrolytically the copper from the resulting solution with the simultaneous regeneration of the solvent used in the process. Many efforts have been made, and many patents have been taken out, both in the United States and abroad, to give this idea practical application, but only within the past few years have the difficulties been surmounted. Leaching and electrolysis, as applied to copper ores, are among the most promising fields in modern metallurgy. New conditions are arising, which will bring the wet methods into prominence; while high freight rates and increasing cost of fuel will tend to limit smelting to highly favored localities. The possibilities offered by the installation of hydro-electric plants and the greatly enlarged range of power transmission will greatly widen the field of electrolytic methods.

Jan 1, 1924

By R. W. Hertzberg, F. D. Lemkey, J. A. Ford

The technique of unidirectional solidification has been applied to the A1-AI3Ni and A1-CuAl2 ezltectic alloy systems; the controlled microstructure of A1-A3Ni consists of parallel A13Ni whiskers emhedded in an aluminum matrix while the Al-CuAl2, system solidifies as parallel alternate lamellae of aluminm and CuAl2. Mechanical tests (tension and flexure) have shown that the particle-matrix interface bond formed during unidirectional solidification allowes for efficient load transfer from the matrix to the reinforcing phase. Strength and fracture characterstics of the alloys were studied as a function of phase orientation; the tensile strength of controlled Al-Al3Ni samples was 43,000 psi (three times greater than that of as-cast specime~s). The strength of the Al-CIA2, cutectic was studied as a function of lamellae-flexure stress-axis orientation using a microbend apparatus. A twofold increase in outer fiber stress was observed as the lamellae were rotated from a position of no reinforcing (perpendicular to the stress axis) to one of maximum reinforcing (parallel to the stress axis), The brittle reinforcing constituent in each alloy (A13Ni and CuAl2) was observed to he the nucleating phase for fracture. It is to be concluded from this investigation that unidirectionally solidified eutectic alloys have a potential use as reinforcing coniposite) materials. In a recent review article, Chadwick1 has described the work of many investigators in the area of controlled solidification of binary eutectic alloys. Thus far, more than twenty eutectic alloys have been unidirectionally solidified to produce structures consisting of two phases in the form of alternating lamellae or as whiskers embedded within a continuous matrix; in either case, the phases are aligned parallel to the growth direction. In particular, Kraft and Albright2 have shown that the Al-CuA1, eutectic alloy exhibits a lamellar microstruc- ture as a result of unidirectional solidification while Lemkey, Hertzberg, and Ford3 have studied the A13Ni whisker-aluminum matrix morphology in the A1-A13Ni system. Whether these alloys could exhibit reinforcing behavior would have to depend upon the strength and volume fraction of the reinforcing phase (AI3Ni and CuA12) and the nature of the bond between the reinforcing phase and the matrix. Hertzberg and Kraft4 have shown that the interface bond between chromium whiskers and a copper matrix in unidirectionally solidified Cu-Cr is particularly good while Lemkey and Kraft5 have reported chromium-whisker tensile strengths in excess of 1,000,000 psi. However, with the chromium volume fraction being less than 2 pct, no reinforcing behavior was displayed by the Cu-Cr alloy.6 In view of the encouraging results concerning the good interfacial bond and high strength of the reinforcing phase in the Cu-Cr system and preliminary mechanical test data reported by Lemkey et al.3 for the A1-A13Ni system, the A1-CuA1, and A1-A13Ni eutectic alloys containing 50 and 10 vol pct, respectively, of the reinforcing phase give promise of possessing mechanical reinforcing behavior. Based on this premise, the objective of the investigation was to study the strength and fracture behavior exhibited by these anisotropic microstructures. EXPERIMENTAL PROCEDURE Controlled Solidification Procedure. An extensive description of the technique of unidirectional solidification has been presented elsewhere.' However, the pertinent details for each eutectic system studied are discussed below. Al-A13Ni System. Several master heats of this alloy were prepared by vacuum-induction melting in an A12O3crucible and casting in SiO2 mold or by induction melting in alumina crucibles under argon. The initial heats were prepared from 99.99 pct A1 and 99.99+ pct Ni, while later heats used 99.999+ pct A1 and 99.99+ pct Ni. Specimens of these master heats were unidirectionally solidified using induction and resistance heating sources and argon atmospheres at growth rates from 1.1 to 28.7 cm per hr. The thermal gradients in the liquid were controlled in the range of 26" to 36°C per cm for these runs. Al-CuA12 System. The master heat and controlled

Jan 1, 1965

By J. L. Huitt, D. K. Lowe

This laboratory flow study covers propping agent transporl in horizontal fractures as influenced by the characteristics of the propping particles, fluid and fracture. Correlations are presented for the transport of particles, deposition and fingering through dunes. For particles moving individually, the article velocity in some cases may be low compared to the hulk average fluid velocity; in other cases, the particle velocity may exceed the bulk average fluid velocity. At high propping agent concentration or low fluid velocity, the likelihood of particle deposition and dune formation increases. Fingering and channeling accompany dune formation. Dune formation can be limited to the outer region of tile fracture by adjustment of pump rate, fluid viscosity and particle concentration. A method is presented by which pump rate and fluid vircosity may he selected to control dune formation for given propping agent concentrations. INTRODUCTION The area and flow capacity of a fracture predominantly control the stimulation derived from hydraulic fracturing. Generation of fracture area exposes the rock matrix to a flow channel; the flow capacity of the fracture controls the flow through the channel to the wellbore under a given pressure gradient. This paper pertains to an important factor that affects the flow capacity of a fracture: the transport of the propping particles in the fracturing during the hydraulic fracturing treatment. With a better understanding of particle transport, fracturing treatments may be designed to obtain more effective distribution of the propping agent. RELATED STUDIES In recent years, the approach to obtaining high fracture flow capacity has been partial monolayer propping. Three papers1-3 have dealt with various facets of this concept. However, in some papers dealing specifically with particle transport, the results generally indicate that packing the propping particles within a fracture is inevitable. In early work&apos; with a sand slurry flowing in a pie-shaped flow cell, qualitative results showed that particle deposition in a fracture during transport should be expected. In other studies"" correlations based on slurry flow in vertical linear flow cells showed particle deposition was primarily a function of fluid velocity. In a recent paper the rate of sand advance (movement of dunes) in a horizontal linear flow cell was discussed. Subsequently, a method was given for designing fracturing treatments, based on the extent of sand advance during a treatment. In this work, particles whose diameter was small relative to the fracture width (i.e., dl W< 0.2) were primarily considered. The particle transport approaches that of sand transport in a stream bed. The industry trend, however, has been to use larger size propping agents. That is, particles with diameters approaching fracture widths predicted by Perkins and Kern.&apos;&apos; This trend has led to generally better fracturing treatments with particle relative sizes in the range 0.2 <d/W < 1.0. In all of the particle transport studies previously cited, the fluid characteristics were discussed. However, little or no attention was given to the parzicle characteristics. In this study the particles. as well as the fluid and fracture, are considered. VARIABLES AFFECTING PARTICLE TRANSPORT In the exploratory work to set LIP a program for this study, it was noted that particles within a batch moved at different velocities in a horizontal linear flow cell. In some cases the particles moved independently. In others there was particle interference. Also, particle deposition and fluid fingering occurred in some cases (Fig. 1). As a result of observing the easily distinguishab&apos;le types of particle movement, the particle variables as well as the fluid variables were included. In addition, the fracture width was included because the fluid velocity profile surely must affect the movement of the larger particles differently than that of smaller particles. Particle variables were density, diameter (based on a sphere of equal volumetric displacement), long and short dimensions, drag coefficient and velocity. Fluid variables were density, viscosity, yield shear strength and velocity. Fracture variables were the width and the angle between the plane of flow and a horizontal plane. Two factors which may prove to be important were omitted because of the complexity resulting from the parameters cited above. These are the fracture-surface roughness and gross irregularities that cause changes in the direction of flow. EXPERIMENTAL EQUIPMENT AND PROCEDURE A linear parallel-plate flow cell (Fig. 2) was used in the study. Lucite plates 1 in. thick formed the test section and permitted a viewing section 11 ft long and 10 in. wide. Spacing between the plates was adjusted with shims to give fracture widths 1/36 to 1/2 in. The model could be tilted to an angle of 45" with the horizonltal plane. Fluid flow was maintained with a Moyno positive displacement pump. Single particles were placed in the flow stream with a particle injector. A .4 - in. diameter plunger moving at a constant rate in a

Jan 1, 1967

By Fred Allison

THE magneto-optic method of analysis had its origin in experiments1 which were designed to detect and measure a time lag in the Faraday effect and later to study this time lag as a function of the wave length of the light.2 Faraday discovered in 1845 that a beam of plane polarized light, when passed through a transparent, isotropic medium traversed by a magnetic field of force parallel to the direction of the light, suffers a rotation. The direction of rotation is reversed with the reversal of the magnetic field and its magnitude depends upon the strength of the field, the length of the path of light in the substance and the nature of the substance. This phenomenon of magnetic rotation is known as the Faraday effect. A question which had been of some interest for years was whether this power of a liquid to rotate polarized light is acquired instantly with the application of the magnetic field, that is, whether it is a case of instantaneity or whether there is a very small interval of time which intervenes between the application of the magnetic field and the consequent rotation of the light by the liquid; in other words, whether there is a time lag in the Faraday effect. Efforts to measure such a lag previously had met with failure. It was recognized at the outset&apos; that since a time lag had escaped detection it must be extremely small, if to a measurable extent it exists at all. It became necessary therefore to adopt a timing device capable of making measures of almost infinitesimally small intervals. The velocity of light served as this timing device, a modification of a method originally employed by Abraham and Lemoine3 being adapted to the requirements of the problem. Since light travels about 30 cm. in a billionth of a second and since settings in our observations may be repeated with deviations not exceeding 3 mm.,

Jan 1, 1932