Search Documents

By P. W. Ramsey, E. J. Boyle, E. A. Anderson

ONLY a few zinc-rich alloys are in commercial use today, and these depend largely upon solid solution effects for their desirable properties. Typical examples are rolled alloys containing about I per cent of copper, with or without additions of elements such as magnesium,1 and die-casting alloys containing about 4 per cent of aluminum with small amounts of magnesium and sometimes copper.2 A number of elements are capable of forming alloys with zinc, which do not enter into solid solution except in limited degree. The present paper considers one such system, zinc-titanium, in which alloys having potentially useful properties in the rolled form were found. ZINC-TITANIUM SYSTEM The zinc-rich portion of the zinc-titanium diagram, as determined by standard methods in this laboratory,3 is shown in Fig. I. The portion of the diagram of significance in the present work extends from 0 to about 0.5 per cent titanium. Gebhardt4 places the eutectic at 0.45 per cent, but the evidence in favor of the composition given in Fig. I is considerable. The solid solubility of titanium in zinc is very low indeed and possibly places these alloys in a somewhat different category from the commercial alloys previously mentioned. ALLOY PREPARATION All of the alloys used in this work were prepared with titanium metal of 98.9 per cent purity. In most cases high-purity zinc (99.99 per cent) was used but sufficient work was done later to show that zinc of about high-grade composition would yield approximately equal results. Best practice in alloy manufacture seemed to be to prepare a zinc-titanium hardener by adding about 4 per cent of titanium metal to molten zinc and holding under a boric acid cover, with frequent stirrings, at 750°C. until the titanium had dissolved. The desired titanium content could readily be obtained in the final alloy by adding the calculated amount of this hardener. The alloys proved to be quite stable in composition, unless overheated, and, with reasonable temperature control, required no cover or flux to prevent loss of titanium content by oxidation. HOT-ROLLING TESTS Three alloys containing, by analysis, 0.05, 0.12, and 0.23 per cent titanium were selected for preliminary study. Slab cross sections revealed a marked grain refinement* (Fig. 2) in the two alloys of highest titanium content. Cast unalloyed zinc has a columnar grain structure similar to that shown for the alloy of lowest titanium content but without the scatter of small equiaxed grains at the center.

Jan 1, 1944

By L. G. E. Bignell, E. A. Hanson, J. O. Lewis

There was a general upward trend of all petroleum activities in Oklahoma during 1933, especially in the last quarter, though the average price for crude oil for the year was below 1932 and overproduction in East Texas demoralized conditions for several months. As the Federal Agencies established under the National Industry Recovery Act began to function conditions in Oklahoma were visibly affected and production of "hot oil" from Oklahoma City field practically ceased. More oil wells were completed, six new fields discovered, extensive geophysical prospecting carried on in many parts of the state, and an increased amount of clean-out and reconditioning work done in older pools during the past year. To increase quantity and rate of recovery of oil many wells producing from limestone formations were treated with hydrochloric acid. The Oklahoma City field had a reported production of 66,984,570 bbl. of oil during 1933, or almost exactly twice the amount reported for 1932. Potential tests and other indicators show that the wells are rapidly approaching the stage where mechanical lift must be applied to all of them, including the wells in the Wilcox sand zone. The major pipe-line companies serving the oil fields of Oklahoma have been anxious to make connections to all wells during 1933 and have indicated a willingness to accept all oil available. The amount offered has been restricted by proration orders, but the state did produce 178,356,-449 bbl. during the year, an increase of about 18.6 per cent over 1932. This increase was practically all due to the greater demand for Oklahoma City oil, as all other pools of any importance showed loss in production or very small gains last year. The U. S. Bureau of Mines' laboratory reports the lubricating distillate content of Oklahoma City crude from Arbuckle and Lower Simpson formations about 17 per cent by volume. East Texas oil is reported to contain about 5.6 per cent lubricating distillates. The desire of the transportation companies to keep their equipment operating at maximum capacity and the need of some refineries for more

Jan 1, 1934

By L. D. Clark, S. S. Saluja

A physical law, governing the rupture of rock by confined explosive charge correspondent to current expressions for determining weight of charge to rupture rock burden, W, was developed in the form Q = cVw3 by two early investigators performing unique experiments with ice. The coefficient C, is found by trial blast. Recent physical tests conducted with rock, synthetic materials and ice to establish the validity of the theory on which it and other related formulae are based indicated: (a) that failure under hydrodynamic impact pressure is by tension rather than shear as was assumed; (b) that the fundamental law of mechanics, enabling the determination of Q = cvw3, modified to the form P = R x Sa x Wb is valid when low velocity explosives are used; (c) that rock breakage under the action of low velocity explosives is entirely due to explosion gas pressure, as was believed; (d) that under the action of high velocity explosive it is due to the joint effects of scabbing and gas pressure; and that further possible modification could make the above equation also applicable to these joint mechanisms. shape could be easily frozen and because large loads would not be required. They found: (a) that the not unfamiliar shearing equation for metals was applicable to ice where P = load in lb; S = periphery of pressure surface, in.; W = burden, in.; K = modulus of rupture by shear in lb per in.2; and (b) that "the form of cavity produced by the application of gradual pressure is similar to that obtained by blasting in rock under similar conditions of free face and pressure surface!" This similarity in crater shapes leads to the conclusion that rock would rupture by shear, as did ice, and its behavior under the force of a blast could be governed by such a relationship as P = S x W x K. Three important interrelated empirical expressions were derived and rock, charging and spacing coefficients C,, C, and e were established and substantiated by trial blasts. In checking the accuracy of the main assumptions, duplication of the ice tests, substituting rock, suggested that K is not constant and that P = K x W x S, though valid for ice, does not necessarily hold for homogeneous limestone.' Conclusions from this later work raised questions making continued investigation desirable because such conclusions do not destroy the practical value of the empirical equations or theory. Further study for the establishment of the relationship between load, burden and periphery of the pressure surface and possible application of these to the mechanism of rock blasting was undertaken by the authors of this paper. MECHANICAL TESTING - EXPERIMENTAL PROCEDURE Certain inconsistencies in the results of the aforementioned tests repeated on three types of limestone suggested these inconsistencies be attributed to rock inhomogeneity. It was also suspected that the loading speed, which could not be held uniform, may have contributed. The earlier work with both rock and ice

Jan 1, 1964

By Theodore J. Hoover

WHAT are the chief branches of the mining engineering profession today? In an effort to analyze the structure of the profession, for practical purposes, a quantitative study has been made of the membership of the A.I.M.E., and is herein reported for the first time. In spite of the effect that a long history and a relatively small group of professional workers have had in limiting specialization in mining engineering, there has nevertheless grown up a wide variety of specialties in this field. More than a hundred different kinds of engineers were discovered among the titles given by Institute members in the Directory, ranging from "advisory engineer" and "American engineer" down to "wire-rope engineer" and "works engineer." How should all these titles be defined and interpreted? How many of them should be relegated as meaningless or confusing? What are the relationships among the remaining useful designations? Should some of them be grouped as "metallurgical" or "chemical," or under some other head?

Jan 1, 1935

By Elliot Rexford

The quality of aggregate materials is of major importance in governing durability and permanence of concrete structures. The problem of selecting suitable aggregate materials is two-fold. Geological factors include the type and character of the aggregate source, presence of known or suspected reactive constituents, and presence of thermally incompatible materials. Laboratory investigations include petrographic studies, soundness and reactivity tests, and tests of thermal properties. The importance of each factor in the selection of satisfactory aggregate material is considered in detail.

Jan 3, 1950

Jan 1, 1967

By Harry P. Hohenadel

DURING the past few years the amazing developments of the chemical industry have inspired so much publicity that the feature writers assure us that we are entering a "Chemical Age," industrially as important as the "Steel Age" and the "Electric Age," so-called. Whether or not these assurances are overstatements, it is a fact that the expansion of the chemical industry during the past 25 years has been enormous. The Chemical Bureau of the War Production Board calculates the value of chemicals produced during 1944 at $8,300,000,000, no small sum even in inflated dollars. As concerns us of the Southwest oil and gas country, four significant trends of the chemical industry are most important. (1) Many of the recently developed chemical products are new creations, not substitutes,. as new and original as the invention of the light bulb, and with a field for exploitation almost as wide. (2) Many of these chemical products will enter the mass consuming markets, which require enormous tonnages of products, and such markets are setting up an industrial demand for chemicals on a mass volume basis, compared to the relatively high-priced low-volume basis ordinarily considered as the chemical outlet of the past. (3) Most of the processes involved in producing these chemicals are adapt. able to the use, all or in part, of natural gas, oil, or refinery gases as raw mate-

Jan 1, 1945

By H. H. Klepfer, K. J. Gill, P. Chiotti

SOME observations relative to the U-Zn system have been made by other investigators. Chipman1 and Carter2 have reported the preparation of several U-Zn alloys and point out that these alloys are generally difficult to prepare. Chipman1 reported evidence for a high melting compound at about 90 atomic pct Zn and the possible existence of a eutec-tic between the compound and uranium. Raynor," in a theoretical discussion of the alloying properties of uranium, included zinc among the elements predicted to have little or no solubility in a, p, or y uranium. In the present investigation, thermal analyses, X-ray, metallographic, and vapor-pressure data were obtained to determine the phase boundaries. The relatively high zinc pressure over most of the alloys at temperatures of 900 °C and above proved troublesome and special techniques had to be employed in preparing suitable alloys. Materials and Preparation of Alloys The metals employed in this investigation were Ames Laboratory biscuit uranium containing less than 500 ppm total impurities and Bunker Hill slab zinc or Baker Analyzed reagent granulated zinc, both with a purity of 99.99+ pct. Due to the high vapor pressure of zinc and the high reactivity of both uranium and zinc with oxygen at only moderately high temperatures, alloys were prepared in closed containers which had either been evacuated or evacuated and filled with helium. High purity magnesia, magnesia containing 10 pct calcium fluoride, and tantalum proved to be suitable crucible materials. Tw-o different procedures, described below, were used to prepare alloys, the latter being the most satisfactory. The metals, uranium turnings and granulated zinc, were cleaned with dilute nitric acid, rinsed, dried, and placed immediately in a helium-fill'ed dry box. The two metals were placed' in a 10 mil Ta crucible. The charge was enclosed in the tantalum crucible by welding on a preformed tantalum cap. This assembly was enclosed inside a stainless steel (AISI 309) bomb. The bomb was made by welding a piece of stainless steel plate on each end of a stainless steel pipe. All these operations were carried out in a helium atmosphere. These assemblies were heated in a muffle furnace at temperatures between 1100" and 1200°C for 10 to 15 min or held as long as 15 to 20 hr in the 950" to 1000°C temperature range before quenching. Spectrographic and chemical analyses showed no tantalum pickup by the alloys, indicating no reaction between the alloys and the crucibles. However, some of these crucibles failed, probably due to imperfections in the welds of the stainless steel or tantalum crucibles. The second and most satisfactory method was to prepare the alloys by powder metallurgy techniques. The procedure was to press degreased and acid-etched uranium turnings with granulated zinc into 20 g compacts under 20,000-psi pressure. The compacts were placed in MgO crucibles, and sealed in evacuated Vycor or fused silica tubes. The alloys were then heated as long as two weeks at about 550°C in a muffle furnace. The pressed compacts were observed to expand by several volume percent during heating and it was necessary to make allowances for this expansion in order to avoid breaking the crucible and Vycor tube. This method was found very satisfactory for preparing alloys which were suitable for thermal analysis or vapor pressure studies. Experimental Methods and Results The phase diagram for the U-Zn system at 1 atrn pressure, shown in Fig. 1, is based primarily on vapor pressure measurements and on thermal analysis taken at temperatures below 950°C. Fig. 2 shows the U-Zn diagram at 5 atrn pressure, constructed on the basis of thermal analysis of alloys in sealed containers up to 1150°C and on the basis of metallographic, X-ray, and analytical data. The alloys sealed under vacuum were actually under their own vapor pressure and those sealed in an atmosphere of helium were under an additional pressure due to the helium. At temperatures up to 1100°C the zinc pressure is 5 atrn or less for these alloys; consequently the maximum pressure over the alloys sealed under a helium atmosphere was 10 atrn or less at temperatures up to 1100°C. Changes in pressure of this order of magnitude do not appreciably alter the position of most solid-solid or liquid-solid phase boundaries. In constructing the phase diagram for a pressure of 5 atm, the effect of pressure on all phase boundaries except those for liquid-vapor or solid-vapor regions was considered negligible.

Jan 1, 1958

By C. A. Bruch, J. F. Duffey

On the basis of metallographic and cooling-rate studies of 15 U-Zr alloys, a new version of the 6 phase region of the U-Zr phase diagram is proposed. IN several published diagrams of U-Zr alloy system:' there is good agreement that at elevated temperatures complete solid solubility exists between y uranium and ß zirconium. Similarly, there is reasonably good agreement concerning the uranium-rich and zirconium-rich ends of the diagram. However, there is no agreement concerning the nature of the diagram at intermediate compositions and at temperatures below about 650°C. The early work of Saller et al.8 hows an intermediate phase, 6. In a later diagram by Saller and Rough' shown in Fig. 1, the d phase field is drawn with dotted lines, indicating doubt that this phase exists. The diagram of Summers-Smith2 does not show the d phase. More recently Holden and Seymour' have shown that in the composition range 40 to 60 wt pet Zr, the high-temperature ? phase, which is body-cen-tered-cubic, transforms to an ordered structure, 8. They found that the order-disorder transformation occurs between 595° and 610°C, and presented a diagram based on the study of four different alloy compositions. Most recently Saller et a1.5 presented a new diagram which differs with respect to the composition limits of the 8 field from the others proposed by these authors. The purpose of the present investigation was to determine the boundaries of the d phase field. Experimental Procedures and Results Alloys—Buttons, weighing 80 g of 15 different alloy compositions were prepared by arc melting Mal-linckrodt uranium and iodide-process zirconium in a water-cooled crucible. A controlled atmosphere of argon and helium was maintained in the furnace. Prior to making each button, a sacrificial button of zirconium was melted to increase the purity of the furnace atmosphere. Each alloy was then melted six times to improve its homogeneity. Subsequently the alloy buttons were jacketed in copper and hot rolled to slabs at 775°C. From these slabs, specimens were machined for chemical, thermal, and metallographic analyses, Table I gives both the estimated chemical composition of the alloys, and the values which were obtained by analysis. The oxygen contents varied from 0.013 to 0.032 pet, nitrogen from 0.0014 to 0.014 pet, and carbon from 0.0013 to 0.011 pet. The purity of the alloys ranged from 99.947 to 99.975 pet. Thermal Analysis—The specimens for thermal analysis were blocks 11/4 x 1/4 x % in. The bead of a calibrated thermocouple was placed between two of these blocks and molybdenum wire was wrapped around the assembly. Each assembly was sealed in a quartz capsule having an argon atmosphere. The capsule was placed inside a refractory crucible which was heated in a furnace. Using a method described by Smith,' the emf of a differential thermocouple, with junctions inside and outside of the refractory crucible, was used to activate the

Jan 1, 1959

By R. I. Jaff, H. R. Ogden, D. J. Maykuth

A phase diagram for alloys containing from 0 to 66.9 pct Mn was determined. Two compounds, tentatively labeled 6 and y, were found in this range. The 6 compound is located at about 66.9 pct Mn and melts congruently at 1330°C. The ? compound has a composition near 53 pct Mn and originates in a peritectic reaction at 1200°C between liquid and 6. ß and Y enter into a eutectic reaction at 1175°C. The ß phase field terminates in a very sluggish eutectoid reaction between a and ? at 550°C. MANGANESE is one of the important alloying addition elements to titanium. As a ß-stabiliz-ing addition for a-ß and ß alloys, it provides high strength with adequate ductility.' Two of the earliest commercial alloys contain manganese as a major alloying component.' The earliest published data on the constitution of Ti-Mn alloys was that of Wallbaum,~ who reported the existence of the compound TiMn2. The transformation range of commercial-purity Ti-Mn alloys was investigated by Craighead, Simmons, and Eastwood' who found limited a solubility and a lowering of the ß transus to about 790°C at 7 pct Mn. Preliminary work by the authors of this paper, using high-purity titanium, confirmed the ß-stabilizing action of manganese and showed the existence of several intermediate phases in the Ti-Mn system." More recently, McQuillan3 determined the ß transus temperatures for high-purity Ti-base alloys containing up through 4.4 pct Mn. These data are given in Fig. 1. The present investigation covered alloys made with a high-purity base. The constitution of titanium-rich alloys made with commercial titanium has been reported4," by Holladay, Kura, and Jackson. The alloy range covered in the present investigation was from 0 to 69.5 pct Mn. This alloy range extends slightly beyond the composition of the first congruent-melting compound encountered on proceeding from the titanium end of the system. A description of the materials and methods used in the determination of the diagram is given in the Appendix. The partial phase diagram determined for the Ti-Mn system is shown in Fig. 2. Details on equilibria in the titanium-rich alloys are given in Fig. 3. Liquid-Solid Relationships Observations on the cast structures of the arc-melted ingots showed that the terminal solid solution of manganese in ß titanium enters into a eutectic reaction with an intermetallic compound labeled ?. As will be shown later, this compound has a composition around 53 pct Mn. The eutectic reaction temperature was determined as 1175°C by thermal analysis which also showed that the ? phase originates in a peritectic reaction at 1200°C. Fig. 4 shows typical eutectic structures for alloy compositions on both sides of the eutectic composition which is located at 42.5 pct Mn. In alloys over the range of 45.4 through 69.5 pct Mn, a second intermetallic compound, labeled 6, was identifield as the primary phase. This phase consistently increased in amount as the manganese content approached 66.9 pct, and, as shown in Fig. 5, an alloy structure containing 66.9 pct Mn consisted essentially of the 6 compound. Thermal-analysis data indicate a melting point of about 1330°C for the 6 intermediate phase. At 67.0 pct Mn, small quantities of a new, higher manganese-content phase were observed in the form of Chinese-script eutectic particles. Comparison of Fig. 6a and b shows an increasing quantity of this phase as the composition was increased to 69.5 pct Mn. The formation of peritectic ? in arc-melted alloys containing 45.4 pct Mn and above appears to be almost entirely suppressed, as shown in Fig. 7a and b. This is because of the narrow freezing range available for its formation by peritectic reaction and because of the very high cooling rates obtained in

Jan 1, 1954

By D. M. James, J. C. Martin

The results are presented of a study of the application of analytical methods to the solution of two-phase flow into single wells. Approximate analytical expressions for the pressure distribution in two-phase flow are found ;;; a number of conditions. The results obtained from the analytical solutions me found to be in good agreement with results obtained by finite difference techniques using a high speed digital computer. Mathematical solutions for four sets of boundary conditions are presented. All of these solutions are composed of a short-term transient plus a steady or quasi-steady state. The rates of decay of the short-lived transients are analyzed. It is found that the durations of the short-term transients may be characterized by a parameter defined as the time constant which can be determined from simple relations. It is shown also that if the outer radius is much greater than the radius of the well. the short term transients decay at rates which are proportional to the square of the exterior radius, and the rates of decay are only slightly dependent upon the radius ratio. Numerical solutions based on finite difference techniques are presented for a number of conditions. The numerical solutions are in good agreement with the predictions based on the theoretical analysis for small and moderate drawdowns. Examples involving large drawdowns indicate that the nonlinearities in the equations of flow do not appreciably alter the longevity of the short-term transients. In all cases the time required for the short-tern transients to disappear is predicted satisfactorily. INTRODUCTION The mechanism by which oil and gas flow into a single well is of vital interest to the petroleum industry. The fundamental equations of two-phase flow which describe this mechanism are nonlinear partial differential equations. Numerical solutions of these equations describing pressure transients have been obtained with the aid of electronic computers. Although solutions obtained in this manner take into account a large number of effects, the reduction of this information to useful generalities is difficult. One method of obtaining generalities is the use of linearized approximations of the nonlinear equations. Since it is possible to obtain explicit solutions of the linearized equation, general properties of the role of pressure in the flow mechanism may be ascertained. Results obtained from this approach are limited to some extent by the linearizing assumptions. The severity of these limitations may be evaluated by comparing solutions of the linear equation with numerical solutions of the more exact nonlinear equations of two-phase flow. In the past considerable amount of work has been devoted to studying pressure build-up using the single-phase flow theory. Unfortunate1y, most prep sure build-up tests involve multiphase flow. A small amount of work has been done studying pressure build-up where the flow is two-phase. The encouraging results of these studies suggest that useful results may be found from additional studies of not only pressure build-up, but also the rapid transients associated with placing a well on production. This paper presents the basic theory of the pressure transients associated with placing a well on production and with closing it in. The paper is concerned chiefly with two-phase compressible flow; however, the results also apply to single-phase flow. The results are based on analytical solutions of the flow equations, and they are verified by numerical solutions using finite difference techniques. Much of the previous work on compressible flow into wells has been confined to single-phase flow. Some work has been done on compressible two-phase steady state flow, and solutions of the equations of flow have been found by finite difference techniques using high-speed computers. Muskat1 presents some rather general solutions to the equations of single-phase compressible flow into wells. Much work has been done on pressure build-up in wells (see, for example, Refs. 2-6). Almost all of the work on pressure build-up concerns single-phase flow with the exception of Ref. 5 and part of Ref. 2. Some work has been done on pressure fall-off in injection wells.718 Muskat9 presents the solution of the equations for radial steady state two-phase compressible flow. Handyl0 extends Muskat's solution to obtain

Sec. 1. The membership of the Institute shall comprise six classes, namely: 1. Members; 2. Honorary Members; 3. Senior Members; 4. Associates; 5. Junior Members; 6. Rocky Mountain Members. All shall be equally entitled to the privileges of membership, excepting that no member of any class whom residence shall be outside of the United States of America, except those residing in Mexico and Canada, shall be entitled to vote. SEC. 2. Members: A person to be eligible for election or transfer into the claw of Member must be at least 27 years of age and must have had at least six years' employment in the practice of engineering, mining, geology, metallurgy, or chemistry, during at least three years of which he must have held positions of responsibility in one or more of these fields. This shall not apply to Rocky Mountain members.

Jan 1, 1934

By Charles W. Bloomquist

The profitability of miscible flooding in a hypothetical target oilfield is examined. The major costs, including Windfall Prof it Tax, are identified and their re1ative importance are discussed. The sensitivity of profit to important physical and economic variables is evaluated and discussed, including variance in oil recovery, oil price, injectant requirements, injectant cost, and capital requirements. Economic sensitivities to important development and operating decisions such as timing, Spacing, Slug size, and gas recycling are also analyzed. The Windfall Profit Tax (WPT) as it applies to gas miscible EOR projects is reviewed. The effect of WPT on each of the various project cases is analyzed and the effect of reduced WPT on remaining production from existing operations is evaluated. Tax implications are compared for integrated vs. "independent" controlled projects and the alternative of expensing vs. capitalizing tertiary injectants is also evaluated. The impact of the Net Income Limitation in reducing WPT. during early and late project life is determined and discussed.

Jan 1, 1982

By D. S. Sanders

IN the four mills of the Cerro de Pasco Copper Corp. in Peru, some 3000 tons of complex sulphide ores are treated daily, with four kinds of concentrates produced: copper, lead, zinc, and pyrite, each containing values in silver, gold, bismuth, and some other metals. Copper occurs in the various ores as chalcopyrite, enargite, tetrahedrite, tenantite, bournonite, and chalcocite; lead as galena; and zinc as sphalerite and marmatite. Small amounts of silver and tungsten minerals are also present. The gangue consist mainly of shale, quartzite, calcite, rhodochrosite, pyrite, and pyrrhotite. In general the values are freed with a relatively coarse grind, about 70 prr cent minus 200 mesh being the finest to which the pulps are ground. In Morococha and Casapalca however. sphalerite particles much finer than this contain inclusions of chalcopyrit r. At Cerro de Pasco the silver and gold are present in all sizes of the ground pyrite.

Jan 1, 1945

By Thomas V. Falkie

Mining and exploration, in the year 1971, can be characterized as a year of politics and the beginning of an era of legislation. Certainly the activities of our state and federal lawmakers and international politicians over-shadowed technical developments, which are outlined in the following pages. The nationalization of the Chilean copper industry was the most far-reaching event of the year. Not only will it have an effect on international metal trade, but the nationalization will also affect the major mining companies in such a way as to cause strategic, managerial and technical adjustments in metal mining and exploration efforts in other parts of the world.

Jan 2, 1972

By S. P. Ray, B. D. Sharma

THE activation energy values for self-diffusion in pure metals have been correlated with a number of physical properties such as melting points,1 valences,' Debye temperatures,3 and cohesive energy densities.4 Extending the melting point correlation, the self-diffusion activation energy values for the alloys can be similarly correlated with the solidus temperatures. For metals and alloys which exhibit phase transformations, such a correlation is not feasible because of the uncertainty of various physical properties of the corresponding phases. Using thermodynamical approach, Ardell5 calculated the hypothetical melting points of the low melting phases of the polymorphic metals. However, these calculated melting points do not show reasonable correspondence with the activation energy of self-diffusion. Recently, a new approach treating metals and alloys as electron concentration phases has been developed by Engel6 and Brewer.7 These workers have attempted to correlate the crystal structures with the electron configurations of the atoms existing either in ground state or in an excited state of low promotion energy. The basic postulate of this theory is that whereas the contribution to the bonding of the metal comes from the interaction of both d and (s-p) electrons existing either independently or in hybridized states, the existing crystal structure is controlled by the (s-p) electrons alone. Specifically, a metal is supposed to crystallize in bcc, hcp, or fcc phase provided the metal has one, two, or three valence electrons per atom in the (s-p) configurations. The diamond, or ZnO and ZnS structures, occur with four (s-p) electrons per atom. Secondly, the contribution of d electrons to bonding is supposed to increase with atomic number

Jan 1, 1970

By R. A. David, D. J. Vink, D. L. Katz

A phase diagram showing boundary curve and quantity of liquid in the two-phase region was determined for a mixture of natural gas and natural gasoline in the region of its critical conditions. The temperatures and pressures of phase measurements were in the range of 85 to 212 F. and 1300 to 2600 Ib. per sq. in., respectively, with the critical conditions at 169.5 F. and 2615 Ib. per sq. in. abs. Color phenomena were observed in the region of the boundary curve from 102' to 192 F. Approximate densities of the single-phase and two-phase regions and analysis of the system are included. Boundary curves between the single-phase and the two-phase regions have been determined for several binary mixtures containing hydrocarbons. 2,3,4.6,7,10,11,12,14 These investigators did not report the relative amounts of liquid and vapor within the two-phase region. The equilibrium values obtained from the dew-point and bubble-point data can be used to compute the lines showing percentage of liquid on the pressure-temperature phase diagram8 but the positions of the lines near the critical temperature and pressure are uncertain. Relative amounts of vapor and liquid were obtained for a gasoline and a naphtha1 within the two-phase area but not in the region of the critical temperature and pressure. The bubble-point and dew-point lines, as well as the percentage liquid lines within the two-phase region, were determined by visual observations in glass apparatus. Apparatus An arrangement of the apparatus is given in Fig. 1, showing the Jerguson gauge A with glass windows B. Pressure was supplied by the

Jan 1, 1940

By R. A. David, D. L. Katz, D. J. Vink

A phase diagram showing boundary curve and quantity of liquid in the two-phase region was determined for a mixture of natural gas and natural gasoline in the region of its critical conditions. The temperatures and pressures of phase measurements were in the range of 85 to 212 F. and 1300 to 2600 Ib. per sq. in., respectively, with the critical conditions at 169.5 F. and 2615 Ib. per sq. in. abs. Color phenomena were observed in the region of the boundary curve from 102' to 192 F. Approximate densities of the single-phase and two-phase regions and analysis of the system are included. Boundary curves between the single-phase and the two-phase regions have been determined for several binary mixtures containing hydrocarbons. 2,3,4.6,7,10,11,12,14 These investigators did not report the relative amounts of liquid and vapor within the two-phase region. The equilibrium values obtained from the dew-point and bubble-point data can be used to compute the lines showing percentage of liquid on the pressure-temperature phase diagram8 but the positions of the lines near the critical temperature and pressure are uncertain. Relative amounts of vapor and liquid were obtained for a gasoline and a naphtha1 within the two-phase area but not in the region of the critical temperature and pressure. The bubble-point and dew-point lines, as well as the percentage liquid lines within the two-phase region, were determined by visual observations in glass apparatus. Apparatus An arrangement of the apparatus is given in Fig. 1, showing the Jerguson gauge A with glass windows B. Pressure was supplied by the

Jan 1, 1940

By Utley Wedge

(Cleveland :Meeting, October, 1012.) In general, the art of securing copper from sulphide ores or concentrates may be said to consist of : (1) separation, in the molten state, of copper sulphide with some iron sulphide, from the great bulk of gangue-material, followed by (2) elimination of sulphur and iron from the molten matte, by oxidation and fluxing, leaving metallic copper. The definition is made broad enough to cover the general practice, whether or not the ore or concentrate is given a preliminary roast for the removal of surplus sulphur. The above process, which I will designate as the smelting process, makes necessary the presence in the ore, or the addition thereto, of such silica, lime, and iron as may be necessary for the formation of a light and fusible slag, together with sufficient sulphur and iron for the formation of copper-matte, and also the addition to the matte of sufficient silica for the oxidation and fluxing-out of the iron. These items, together with the cost of fuel sufficient for melting the mass, constitute important items of cost in the copper-smelting process. Numerous cases where fluxing-materials are scarce or dear, or where fuel is expensive, have caused special attention to be given recently to the wet process of copper-extraction, which may be designated as consisting of forming soluble copper salts which are then washed or leached out of the ore or concentrates by dissolving in water or acid. Metallic copper may then be secured from the solution of copper salts by electrolysis; by cementation; or copper can be brought out of the solution as a * Presented also at the Joint Meeting of the Institute and Section IIIa, Metallurgy and Mining, of the Eighth International Congress or Applied Chemistry, New York, N. Y., September, 1912, and here published by mutual agreement.

Dec 1, 1912

By T. S. Fuller

The work of D. J. McAdam, Jr.1,2 at the U. S. Naval Engineering Experiment Station, Annapolis, Md., on what has been called by him "corrosion-fatigue" has focussed the attention of the engineering profession in general, and of those interested especially in the study of corrosion in particular, on the importance of making tests which will indicate as nearly as possible what can be expected from a given material in service. Pitting is unquestionably the chief agent operating so tremendously to reduce fatigue limits, but in the light of previous work3, 4, 5, 6, 7, 8 it is fair to assume that absorbed hydrogen resulting from the action of the corroding medium upon steel may, under certain conditions, have a perceptible influence. The experiments described in this paper deal more precisely with stressless corrosion, or "prior-corrosion fatigue,"9 and have been carried out to test such an assumption, to segregate, if possible, the effect of pitting from that of absorbed hydrogen, and although very preliminary in nature they indicate results which are striking.

Jan 1, 1929