Search Documents

By J. W. Freeman, J. P. Rowe, R. F. Decker

HEAT-to-heat variations in properties of an alloy of constant nominal chemical composition have been a perplexing problem to the metallurgist. These heat-to-heat differences have been especially baffling in high-temperature metallurgy. In order to establish fundamental reasons for these heat-to-heat variations, the National Advisory Committee for Aeronautics has sponsored and financially assisted an extended research program on heat-resistant alloys at the University of Michigan. As part of the program to find the contribution of processing variables, Frey, Freeman, and white' studied effects of heat treating on nickel-base alloys and Ewing and reeman' investigated effects of hot-working practice on N155 alloy. To extend the program to the study of effects of melting practice on high-temperature properties, a 55 Ni-20 Cr-15 Co-4 Mo-3 Ti-3 pct A1 composition was selected for experimentation. The objective of this program was to establish the melting-practice variables which influenced the hot-working characteristics and creep-rupture properties and, at the same time, establish the metallurgical mechanisms for the effects. During the course of the investigation of practices using vacuum melting, it became increasingly evident through chemical analyses supplied by industrial concerns that a major variable was melt reaction with the crucible. This paper is devoted to the results of this phase of the melting-practice study. EXPERIMENTAL PROCEDURES Experimental 10-lb heats were induction melted in the University of Michigan vacuum-melting unit with the melting practices outlined in Table I. Aim analysis for the basic alloy, in wt pct, for all heats was as follows: Cr Co Mo Ti Al 20.0 15.0 4.0 3.1 3.1 Mn Si C Ni 0.12 0.12 0.08-0.15 Bal. Small amounts of boron and zirconium were added to certain heats as listed in Table I. These additions

Jan 1, 1959

By Akinobu Kasami, Keiji Maeda, Makoto Naito, Masaharu Toyama

Gap electroluminescent diodes have been prepared by the vapor phase diffusion of zinc into n-Gap crystals which were grown from a gallium solution (10 wt pct Gap) doped with tellurium and Ga203. A marked improvement in the efficiency of the red electrolumines -cence has been achieved by heat treatment after diffusion. External quantum efficiencies of diodes annealed under optimum conditions are 0.2 to 0.6 pct at room temperature, or about 200 times higher than the efficiencies of diodes quenched after diffusion. The optimum dopant concentrations in the gallium melt from which the crystals were grown are 3to6 x at. pct Te and 4 to 8 x 10-2 mol pct Ga203. The efficient diodes are characterized by linearly graded junctions with an i-layer 0.1 to 0.2u thick. Annealing increases the emission intensity by a factor of 20 to 50 and decreases the current density to 1/3 to 1/8 that of quenched diodes at a given bias. The decrease in current is attributed to an annihilation of deep recombination centers in the depletion layer. The increase in emission intensity is interpreted in terms of an increase in lifetime of minority carriers and an increase in the relative intensity of red-to-infrared emission. The dependence of these quantities on the tellurium and oxygen doping levels is also discussed. A number of studies have been made of the red light emission from for ward-biased Gap diodes.' At room temperature this emission band is centered at 7OOO? with a spectral width of nearly 1000?. Low-tempera-ture photoluminescence indicates that this emission is due to either the radiative annihilation of an exciton bound to a pair of zinc and oxygen atoms substituting on nearest neighbor lattice sites2,3 or the radiative recombination of an electron bound to this Zn-O pair with a hole bound to an isolated zinc shallow acceptor.3 An emission band is also observed with a spectral peak at 9800?. This infrared emission has been shown to be due to the recombination of an electron trapped at an isolated oxygen deep donor with a hole trapped at an isolated zinc acceptor.4 The red emission from Gap diodes is fairly efficient at room temperature because the nearest neighbor Zn-0 pair forms a deep electron trap at 0.3 to 0.4 ev below the edge of the conduction band.2'4 In diodes grown by liquid epitaxy an external quantum efficiency of 2.1 x 10-2 (photon/electron) has been attained by heat treatment at relatively low temperatures.5 This heat treatment was found to increase the efficiency by a factor of 3 to 6. However, no detailed studies have-been reported on the effects of heat treatment. We can only cite Onton and Lorenz's work6 on the change ; in the relative intensity of red-to-infrared emission. Heat treatment has also been tried on junctions built in during growth, but contrary to expectations the efficiency decreased. In-diffusion is a simple and controllable method of fabricating p-n junctions. For Gap, zinc is generally used to form a p-type layer on n-type crystals. The emission efficiencies of in-diffused diodes are, however, extremely low in comparison with liquid epitaxial diodes.' Although efficiencies as high as 2 x 1O-3 have been reported, values from 10-6 to 10-4 are generally obtained by typical diffusion techniques. Out-diffused diodes are known to be a little more efficient than in-diffused diodes. Nevertheless, the quantum efficiency is at most 7 x 10- 3 and ordinarily of the order of 10-4.8 NO results have been reported on heat treatment of either in-diffused or out-diffused diodes. This paper reports a marked improvement in the efficiency of the red emission observed for in-dif-fused diodes as a result of heat treatment after diffusion. The method described reproducibly yields diodes with external quantum efficiencies of 2 to 6 x 10-3. The observed dependence of efficiency on annealing time and on doping level will be discussed in terms of the lifetime of minority carriers and the formation of Zn-O complex pairs. EXPERIMENTAL A) Diode Fabrication. The n-Gap crystals used in this study were grown from a saturated gallium solution by a slow cooling method.8 The Gap content in the gallium melt was fixed to 10 wt pct corresponding to a growth temperature of about 1100 Tellurium was chosen as the n-type dopant and added to the melt in concentrations ranging from 0.001 to 0.06 at. pct. Oxygen was added in the form of Ga2O3, whose concentration was varied from 0.004 to 0.2 mol pct. The resulting crystals were platelets with well-developed (111) surfaces. Typical electrical properties were Hall mobilities of 130 to 30 sq cm per v-sec and carrier concentrations of 1016 to 10" cm-3 at room temperature. Diodes prepared from crystals with relatively low doping levels, in which u = 130 to 100 sq cm per v-sec and n = 0.6 to 6 x 1017 Cm-3, were examined in detail. The p-n junctions were produced in these n-Gap crystals by the diffusion of zinc from the vapor phase by the following procedure. The platelets were carefully lapped on both sides to a thickness of 150 to 200 u while maintaining the (111) orientation. After being etched in hot aqua regia, the crystals together with the zinc were sealed in an evacuated 12 mm ID quartz ampoule 20 cm long. The crystals and the zinc were then separated from each other at opposite ends

Jan 1, 1970

By Ernest Burchard

A RECONAISSANCE of the chrome and manganese'1ore deposits of Culm was made in the spring of 191s by Albert Burch representative of the U. S. Bureau of Mines and the writer representing the U. S. Geological Survey. The object of the study was to obtain authentic information for use of the: United States Government as to the location, character, size, and availability of the Cuban deposits of the ores of these important steel-alloy metals. The Cuban Government courteously detailed Sr. E. I. Montoulieu, a mining engineer connected with the Treasury Department, to act as escort and associate throughout the work on the Island. Mr. George A. Wright, of Baracoa, Cuba, a mining engineer especially familiar with the chromite deposits of Oriente Province, was a member of the party from Feb. 25 to Mar. 20. It was possible to visit most of, the chrome-ore deposits that seemed to be of promise, but there was not sufficient time to visit all that were brought to our attention, some of which may have merit. Furthermore, no attempt was made to examine the extensive chromiferous iron-ore deposits of the Mayari, Moa, and Cubitas districts, as these deposits cannot be regarded as sources of chromium except indirectly. At the close of the field work the essential data concerning the quantity and quality of ore probably available for shipment during 1918 and 1919, in the event of the continuation of the European war, and of the tonnage of ore in reserve, were furnished to such Government bureaus as were interested, including the Shipping Board and the War Industries Board, and as soon as chemical analyses of the chrome ores could .be obtained, a press bulletin on the subject was published by the Geological Survey. In the present paper the engineering data, and tonnage estimates contained in the unpublished notes of Mr. Burch have been freely used, and their helpfulness is hereby gratefully acknowledged. Many thanks are due Senor Montoulieu and Mr. Wright for their valuable work in the field; to the officials of the Spanish American Iron Co. and of the various other companies; and to individuals holding chromite claims, for courteously facilitating the work of the party. In the study of material for the present paper, chemical analyses have been made by R. C. Wells and petrographic determinations and descriptions were furnished by Miss E. F. Bliss, both of the U. S. Geological Survey.

Jan 9, 1919

By E. W. Felegy

THE need for improved mine communication to increase efficiency and to insure greater safety has long been recognized. General and unrestricted communication between all points underground, and between the surface and all points underground, is probably the least advanced phase of the mining industry. An ideal system of mine communication must require no fixed wire installations. The equipment must be small, lightweight, and readily portable, and the power requirements low. A system that can be used not only under normal circumstances but also in an emergency, when the continuity of wires, tracks, and pipelines may be disrupted, must function independently of any aid furnished by standard installations. Radio communication offers possibilities of meeting all the requirements necessary for an ideal communication system in underground mines. Transmission of signals must be achieved through one or both of two mediums, through the air in mine openings or through the strata. The results or lack of results obtained by early investigators showed conclusively that radio communication by space transmission cannot be accomplished effectively beyond line-of-sight distances in underground passageways. A radio system underground therefore must depend solely upon transmission through soil and strata. The application of radio to underground mine communication was investigated by many individuals and agencies at different times in the last several decades, but little success was achieved before World war 11.2-0, The results of experiments during the war, and further knowledge gained in experiments with vastly improved communication methods and equipment after the war provided the background for additional research in radio communication in underground mines. During 1950 to 1.952 the University of Minnesota sponsored an investigation to determine the possibility of developing: a system of radio communication universally applicable in underground metal mines in the Lake Superior district. The possibility of using radio equipment to determine the imminence of rock bursts in deep copper mines in that district also was investigated. The investigation supplemented previous and concurrent emergency mine communication studies of the U. S. Bureau of Mines. Testing equipment and laboratory facilities maintained by the Bureau of Mines at Duluth, Minnesota, were used in the research program, which was conducted as a mining engineering graduate research problem by the present writer under the direction of T. L. Joseph and E. P. Pfleider. The radio units used in the research program were designed and built to specification solely to conduct tests of radio communication in mines. Two identical units were used in all tests. Each unit contained a transmitter section, a receiver section, and a power-supply section, mounted on a single chassis. The entire unit was enclosed in a single 10x12x18-in. metal case provided with a leather-strap handle for carrying purposes. The front of the case was hinged to open upward and provide easy access to the single control panel on which all controls were mounted. Storage batteries supplied the operating power for all tests. Standard 6-v automobile batteries were utilized to provide adequate capacity to conduct tests for a full day without exhausting the battery. A frequency range from 30 to 200 kc was covered in eight pre-fixed steps on each unit. The carrier frequencies were crystal-controlled and amplitude-modulated. The receiver employed an essentially standard superheterodyne circuit and was sufficiently sensitive to detect signal strengths of 5 micro v. A heterodyne circuit was employed in the transmitter to obtain the low-carrier frequencies used in the units. Power output of the transmitter, usually less than 2 w, rarely exceeded 3 w in any test. Tests were conducted in mines on the Vermillion iron range in Minnesota, the Gogebic iron range in Wisconsin, the Menominee and Marquette iron ranges in Michigan, and a copper mine in the upper Michigan peninsula. All tests were conducted when the mines were operating normally, and usual mining, maintenance, and transportation activities were in progress, so that any interference caused by normal production activities could be evaluated during the tests. Tests were made between different points underground in each mine, and between underground and surface points at some mines. Test readings obtained at any one mine were calibrated in the laboratory before another series of tests were begun at the next mine. The transmitter and receiver were separated by one or more levels in each test, and generally there was no other means of communication between test points. Two 100-ft lengths of rubber-covered wire were used for antenna wires on each unit in both transmission and reception. The ends of the wires were connected to ground points in one of several methods, depending upon physical conditions at each test site. The wires were clipped to metal rods about 200 ft apart in the back, side, or bottom of the mine opening where the character of the rock permitted driving rods. Both wires were clipped to points about

Jan 1, 1954

By F. J. Plecity, J. T. Michalak, W. C. Leslie

Isothermal recrystallization and grain growth in zone- and vacuum-melted irons and Fe-Mn alloys, up to 0.60 pct Mn, were studied in the range 480° to 650° C, after 60 pct cold reduction. In initial stages, rate of grain growth and rate of recrystallization of iron decrease with time. The recrystallization is typical of a growth-controlled process, and rate of growth is determined by the extent of recovery. Mn decreases rates of growth and of recrystallizatzon. The recrystallization process changes at about 0.30 pct Mn and nucleation may become time-depetzdet~t. In recent years, considerable effort has been expended in determining the effects of solute elements on recrystallization and boundary migration in fcc metals. The results have indicated that the effects produced by single solute additions are dependent upon both the element added and its concentration.'-' In contrast, there have been very few attempts to determine the characteristics of recrystallization and boundary migration in high-purity bcc metals, especially after heavy deformation, and the effects thereon of single solute elements.9-11 This study was undertaken to determine the recrystallization characteristics of various "high-purity" irons and the effects of manganese additions at two levels of base purity. It was hoped that the information obtained would improve our understanding of the recrystallization of pure metals and aid in formulating a theory for the effect of solute elements. The interest was not entirely academic, for the annealing of low-carbon steels, which is of very great commercial importance, is but poorly understood. MATERIALS The compositions of the irons and iron-manganese alloys used are listed in Table I. The zone-melted iron and Fe-Mn alloys were made by Battelle Memorial Institute. Iron S-1 was arc-melted in a water-cooled steel mold in an argon atmosphere. The ingot was forged into a bar, then given two horizontal zone-refining passes in an alumina boat. Iron V-4 was treated in a similar manner, but was not zone-refined. The iron for the zone-melted Fe-Mn alloys was induction melted in vacuum in MgO crucibles and cast into alumina molds. The ingots were forged into bars, machined to shape, and a groove milled down one side of each. The best available electrolytic Mn was placed in the grooves, and the bars were zone melted. The vacuum-melted Fe-Mn alloys were induction melted in this Laboratory in MgO crucibles and poured into cast-iron molds. Iron V-5 was purchased from National Research Corp. in the form of a small vacuum-cast ingot. The low-carbon steel was made by induction melting in air at the U.S. Steel Corp. Applied Research Laboratory. The history of the materials prior to the final cold reduction differed; these details are given in the Appendix. The penultimate grain size of the principal materials was kept in the range ASTM 2 to 4, except for the low-carbon steel. PROCEDURES The cold work prior to the final recrystallization anneal was kept constant at 60 pct. It is known that rolling procedure can influence the kinetics of recrystallization of ironI2; therefore, all specimens were rolled in one direction only, between clean,

Jan 1, 1962

ALBERT Ladd Colby, who died suddenly of influenza at Torquay, England, on Apr. 30,1924, was born in New York City, on June 26,1860. He was educated in the public schools of New York, at the College of the City of New York, and received the degree of Ph. B. from the Columbia School of Mines in 1881. He continued his studies at Columbia, acting occasionally as assistant to Prof. C. F. Chandler, until 1883. For the next three years he was Assistant Professor of Chemistry in Lehigh University; then head chemist and metallurgical engineer of the Bethlehem Steel Co., at Bethlehem, Pa., occupying the latter position until 1903. As head chemist his active and inventive mind devised several improvements in apparatus for increasing the rapidity and accuracy of the analytical work; as metallurgical engineer, he was, from time to time, in charge of the blast-furnace, open-hearth, bessemer, and puddling departments; he had entire charge of the inspection, assignment, and economic use of all metallurgical materials, and he early gave his attention to the formulation of specifications for metallurgical materials—an activity in which he long held a distinguished part in this country, and as a representative of his own country in England and Europe. He also sewed as expert for his company in patent suits, again laying the foundation for valuable service later as a consulting engineer. In this latter capacity he was excelled by few, if any, contemporaries in the iron and steel industry. His mind was ingenious, thorough, clear, and keen, both in the preparation of evidence and its presentation to the Court. He very quickly appraised the value of evidence, or of an answer to a question, and knew how to secure the infermation, either from the available literature of any language, or by special researches or plant studies. In the executive control of literary research for patent purposes, his long training, infinite capacity for digging through long series of articles in English, German or French, and clear formulation of the vital subject matter for the guidance of assistants, made him invaluable. He was also an adept in collecting information on special branches of his profession. For example, when the science of metallography began to assume importance, he made the first really comprehensive bibliography covering the literature of all siderurgical countries; for the newly formed International Nickel Co. he gathered all the information extant on the subject of nickel steel, both in the literature and in the minds of experts in America and Europe. Two books testify to the thoroughness of his work in this capacity, vie.: "American Standard Specifications for Steel,"

Jan 1, 1924

By W. J. Reagan

IN a study of the life of ingot molds, it is essential to eliminate all of the variables. In the commercial manufacture of steel this is almost an impossibility. In this study many of the variables have been eliminated, and because of the unusually consistent furnace practice, with small variations in the type of steel manufactured, and a similar type of mold design for all ingot sizes, it is possible to determine with some degree of accuracy the cause of variations in ingot-mold life. All of the ingot molds in this study were used in the production of basic open-hearth killed steel with chemical analyses within the following range: C, 0.50-0.85 per cent; Mn, 0.60-0.80; Si, 0.20-0.30; S, 0.04 max.; P, 0.04 max. All ingot molds were of the closed-bottom type and used for bottom casting only. None of the molds in the study failed from cutting of the sides due to top casting; in fact, on only rare occasions are any molds used for top casting. The general type of this mold is shown in Fig. 1. All sizes have rather a heavy band of metal, about 6 in. wide, at the top to give mechanical strength at this point, and all have cast lugs. Cross sections of the vari-ous sizes from top and bottom sections are shown in Fig. 2. Ratios of wall thickness to ingot weight, ratio of ingot diameter to ingot length, and other figures of interest are shown in Table 1. In. the majority of cases, the cause of failure in this type of mold is due to heavy fire cracking on the "flats" at a point from 3 to 6 in. from the bottom radius of the mold. Fig. 3 pictures this type of failure. The start of failure at these points usually begins with a very small section of the interior surface becoming involved. As a rule, a section of 1 or 2 sq. in. is the first noticeable 'indication that mold failure is taking place. Gradually the small section increases until a sizable cavity develops, causing a protuberance on the bottom of the ingot, which eventually becomes too large to be stripped. The mold is then removed from service. At the time of failure, this cavity often reaches a size of about 5 sq. in. and about 1/2 in. deep. Sometimes cavities are found on only two or three sides and at other times all twelve sides appear to be involved.

Jan 1, 1936

By W. J. Reagan

In a study of the life of ingot molds, it is essential to eliminate all of the variables. In the commercial manufacture of steel this is almost an impossibility. In this study many of the variables have been eliminated, and because of the unusually consistent furnace practice, with small variations in the type of steel manufactured, and a similar type of mold design for all ingot sizes, it is possible to determine with some degree of accuracy the cause of variations in ingot-mold life. All of the ingot molds in this study were used in the production of basic open-hearth killed steel with chemical analyses within the following range: C, 0.50-0.85 per cent; Mn, 0.60-0.80; Si, 0.20-0.30; S, 0.04 max.; P, 0.04 max. All ingot molds were of the closed-bottom type and used for bottom casting only. None of the molds in the study failed from cutting of the sides due to top casting; in fact, on only rare occasions are any molds used for top casting. The general type of this mold is shown in Fig. 1. All sizes have rather a heavy band of metal, about 6 in. wide, at the top to give mechanical strength at this point, and all have cast lugs. Cross sections of the various sizes from top and bottom sections are shown in Fig. 2. Ratios of wall thickness to ingot weight, ratio of ingot diameter to ingot length, and other figures of interest are shown in Table 1. In the majority of cases, the cause of failure in this type of mold is due to heavy fire cracking on the "flats" at a point from 3 to 6 in. from the bottom radius of the mold. Fig. 3 pictures this type of failure. The start of failure at these points usually begins with a very small section of the interior surface becoming involved. As a rule, a section of 1 or 2 sq. in. is the first noticeable indication that mold failure is taking place. Gradually the small section increases until a sizable cavity develops, causing a protuberance on the bottom of the ingot, which eventually becomes too large to be stripped. The mold is then removed from service. At the time of failure, this cavity often reaches a size of about 5 sq. in. and about 1/2in. deep. Sometimes cavities are found on only two or three sides and at other times all twelve sides appear to be invoIved.

Jan 1, 1937

By P. D. I. Honeyman, P. A. Faust

At the Miami plant of the International Smelting Co., Inspiration, Ariz., there are four reverberatory furnaces, all 120 ft. long. At present only one of these furnaces is in operation. It is operated as a wet-charge furnace, the charge being distributed for about 65 ft. down the furnace length. Usually this charge contains about 12 per cent moisture and runs 25 per cent sulfur, of which there is eliminated in the furnace from 25 to 30 per cent. The furnace is oil-fired, the fuel being burned in a battery of Cananea-type, low-pressure burners. The flame is kept short and conditions so adjusted as to obtain complete combustion within the furnace. The average furnace draft, taken through the verb arch, amounts to only 0.02 in. of H2O. Draft is purposely kept low to cut down infiltration through the flues and boiler settings, and control dampers are regulated to maintain this uniform condition throughout the charging as well as the smelting period. Hot gases discharge from the furnace uptake through a common header flue to the waste-heat boilers. The general layout and dimensions of the plant are shown in Fig. 1. Four Stirling boilers, two of class M-26 (713 hp.) and two class M-31 (850 hp.), serve the furnace. Three usually are sufficient to take care of normal operation, the fourth boiler being used as a spare when necessary. The distribution of hot gases to the various boilers is regulated by the dampers in the boiler exit flues. Normally the boilers closest to the furnace uptake would evaporate more water than do those farther away, but dampers are regulated so as to distribute fairly well the load between the several boilers. Steam from the waste-heat plant is delivered to the adjoining power house of the Inspiration company, where it is used both in the Nordberg blowing engines and for electrical generation. Steam pressures and temperatures recorded are those in the main power-plant header and are thus inclusive of all losses in about 500 ft. of 10-in. line. Steam for smelter heating and auxiliary use is taken from the main waste-heat header, is reduced to 125 lb. and distributed through separate lines. Boiler feed water is supplied by the power plant and consists of returned condensate, augmented to a large extent by make-up water

Jan 1, 1934

By J. A. Roberson, Robert A. Rapp

From the observation of platinum wire marker movement in the oxidation of columbium at high lemperatures and low oxygen pressures, predonzinant cation diffusion in CbO, has been demonstrated. The Cu,0 molecule was used as an oxidizing species to study the nature of the porous scale and the location of the reduction site in the oxidation of colum-bium. The Cb205 scale contains microporosity and forms by alternate ionic diffusional growth and fracture. The oxidation of columbium at high temperatures and very low po, results in a relatively compact and protective Cb205 layer. THE observation of marker movements during oxidation is one means for the identification of the mobile ionic species in an oxide lattice. Previous marker experiments in the oxidation of columbium have all resulted in the markers being found on the outside surface of the Cbz05 scale. The Cr203 powder markers of Klopp et a1.,' the gold film marker of Kofstad and ~jijllesdal,' and the platinum wire marker of Cathcart et a1 .3 were found at the oxide/gas interface for oxidation temperatures ranging from 450" to 120O0C. However, in all experiments relatively high oxygen pressures were used. As discussed by Mrowec, even the interpretation of marker experiments in simple scales containing only one compound is not without ambiguities. In brief, it can be said that a marker may be found almost anywhere in the scale layer if the metal oxidizes by cation diffusion through the scale; the position of the marker depends upon morphological happenings in the scale. When considering marker movement in a polyphase scale one must proceed with extreme caution. For example, in the past (and present) work markers have never been found at the columbium-scale interface, and one might infer that the oxygen ion is mobile in CbO and CbO,. However, only trace quantities of CbO and CbOz have been present on any of the specimens, so no firm statement is justified on this basis. Despite previous experimental work, considerable doubt still exists concerning the role of the oxides CbO and CbOz in the oxidation of columbium. The identification of the mobile ionic species in CbO and CbOz from the observation of platinum wire markers was one goal of the present investigation . The linear kinetics of columbium oxidation at high temperatures (T - 1000°C) suggests that the Cbz05 scales which form on columbium are porous. From mercury absorption measurements on a Cbz05 scale formed at 500"C, Aylmore et al.' reported a minimum volume fraction of connected voids equal to 0.15. While these scales often appear to be quite porous when viewed in metallographic cross section, they are so brittle that metallographic preparation is likely to exaggerate any porosity originally present. In this investigation, porosity developed during the oxidation of pure columbium and present at the high temperature was detected by oxidizing specimens in sealed evacuated capsules containing large compacts of mixed copper and CuzO powders. wooda has demonstrated that the CuzO, or (CuzO),, molecule is volatile and that oxygen is transferred by the CuzO molecule from a Cu/CuzO mixture to materials having a greater affinity for oxygen. For each molecule of CuzO that is reduced at a sink for oxygen, two atoms of copper are deposited. Quantitatively, essentially all of the oxidation carried out by a Cu-Cu20 compact results from a displacement reaction involving the CuzO molecule. When a metal which oxidizes to form a porous scale is exposed to the CuzO vapor, the CUZO molecules are reduced in the pores leaving a deposit of metallic copper to mark the site of the reduction. This technique has the rather unique advantage that any copper-coated pores found in the scale are unambiguously related to the reduction site in the growth of the scale under consideration. Pores or cracks which form in a msition*- external to the reduction site or which occur as a result of cooling or handling of the specimen will not exhibit the copper deposit. EXPERIMENTAL PROCEDURE Marker experiments were made on columbium metal, and on pellets of CbO which had been pressed and sintered. Platinum wire markers (0.001 and

Jan 1, 1968

By Wallace E. Pratt

TO SERVE their primary function of balancing supply with demand. crude-oil prices must not only return full cost plus a reasonable earning to the efficient producer but they must also offer an additional reward to stimulate exploration sufficiently to maintain adequate reserves. High prices increase the volume and efficiency of exploration; low prig e- -Idle exploration. Over the last decade average prices for crude oil have been much lower than for the proceeding ten years, and lower even than the average over the life of industry. Under these circumstances no one should be surprised to learn that over this same recent period of discovery of new oil fields has also lagged and fallen below its average level for the previous decade. Crude oil prices have been too ion to support the required activity in wildcatting.

Jan 1, 1941

By A. G. McGregor

During the past 5 years, five new copper-smelting plants have been built and put into operation in the State of Arizona. The monthly copper output from these plants averages from 5,000,000 to 18,000,000 lb. Previously, there never was as much activity in copper-smelting plant construction in the same length of time in all the rest of the world. Naturally, in this amount of work, some new problems were met and new features in plant design and equipment developed. Some of these features are described in this paper. Concentrate Hauling, Unloading and Sampling System (a) Concentrate Car The International Smelting Co. has provided at its plant at Miami specially designed cars for hauling the concentrates from the mills of the Inspiration Copper Co. and the Miami Copper Co. The car has a bottom that is readily made tight to hold flotation concentrates and is quickly and cheaply unloaded. Figs. 1, 2 and 3 show views and details of the car. The main feature of this car is the slot in the bottom throughout its length, which is closed by means of short planks that overlap like ship-lap as shown by Fig. 1. At one end of the car an iron gate operated by a screw and hand wheel is provided, which clamps or presses the planks together, making the bottom tight. A removable tapered plug rests vertically over this gate when the loading of the concentrates at the mill commences. A concentrate unloading pocket (Fig. 4), 180 ft.long, is provided at the smelting plant, which has a conveyor belt running throughout its length underneath the track. To unload a car, the vertical plug at the end of the car is lifted by means of a chain hoist which is supported by a trolley overhead. The gate at the end of the car is opened approximately 18 in. The removal of the plug leaves a hole down through the concentrates. The concentrates are poked through the hole from the top of the car until it is convenient for a man to stand on the bottom and draw one of the slats in the bottom toward the gate end of the car. The concentrates are then raked down with hoes on their natural angle of repose,

Jan 1, 1917

By E. C. Truesdale

A FEW years ago H. M. Cyr, working in the Research Laboratories of The New Jersey Zinc Co., produced a few pounds of zinc1 of such purity that no other elements were detected in it by spectrographic analysis, using the facilities then available. This zinc contained less than one ten-thousandth of one per cent of metallic impurities.2 During the decade that followed upon the laboratory production of this "spectro-graphically pure" zinc, commercial developments brought about the production of large tonnages of zinc of purity exceeding 99.99 per cent, and today zinc of 99.999 per cent purity is produced and marketed as "chemically pure" zinc. Typical analyses of present supplies of high-purity zinc are given in Table 1. TABLE 1.-Typical Analyses Percentage by Weight Sum of Zinc Pb, Fe, Pb Fe Cd Al Cd Special High Grades 0.007b 0.005b 0.0056 none 0.0106 C.P. (chemically pure) <0.0002 0.0005° 0.000052 S.P. (spectrographically pure).. <0.0002d <0.00005d a A.S.T.M. Standard Specification for Special High Grade Slab Zinc (A.S.T.M. Designation: B 6-37). b Maximum. c Fe chemically determined. Pb and Cd are spectrographically determined. d Differences between composition of C.P. and S.P. zinc are discussed later in this paper. The availability of commercial tonnages of special high-grade zinc has been the basis for the development of the zinc-base die-casting alloy industry which, in the year 1936, consumed one-eighth of the zinc used in the United States for all purposes. This and the C.P. and S.P. grades have given impetus to scientific investigations into the properties of pure

Jan 1, 1939

By Robert T. MacMillan

Of all the mineral substances utilized by man, salt or sodium chloride has one of the longest and most varied histories. Because all animal life is descended from marine organisms, sodium and chlorine became necessary to life, and as sodium chloride meets requirements most readily, common salt has been essential to human and animal diets from earliest times. As civilization progressed, man learned to evaporate sea water and brines of saline lakes and springs to obtain salt, and gradually ceased to depend on the flesh of animals and the occasional salt outcrops or "salt licks" they frequented. He also learned that salt had a multitude of uses, particularly as a preservative of meat and other foods. The importance of salt in the minds of early men may be readily seen from many allusions in the Bible and other ancient writings. Expressions such as "not worth his salt," and "the salt of the earth" are deeply embedded in the English language. Salt has symbolized friendship, fidelity, purity, and hospitality. It has been used as currency; had religious significance; caused wars; and has been a favorite commodity for taxation. The English word "salary" stems from the Latin word for salt, in which Roman soldiers received part of their pay. Although salt today retains its dietary importance, it has thousands of other uses. Of each 100 pounds produced in the United States less than three pounds is for table use. The other 97 pounds goes for agricultural, industrial, and chemical uses. Fortunately, reserves of salt are enormous and reasonably well distributed on the face of the earth. The sea is an inexhaustible source of salt which may be had at prices which vary with climate and other factors. In addition, large underground salt deposits and many salt lakes, springs and playas are scattered throughout the world. Most countries have access to a salt supply, although some are more favored than others. Properties Crystallized sodium chloride or common salt is known as halite. Its molecular weight is 58.454 and it contains, by weight, 39.34 pct sodium and 60.66 pct chlorine. Alternate positions in the cubic lattice are occupied, respectively, by negative chloride and positive sodium ions; the crystal form is isometric. Crystallization from water produces concentric shells, and when broken, a crystal shows conchoidal fracture. Salt has a hardness of 2.5; its specific gravity ranges from 2.1 to 2.6 for rock salt and is 2.165 for the pure crystal. The refractive index is 1.554; it melts at 800.8 ± 0.5°C and boils at 1413°C. Its heat of fusion is 123.59 cal/ gram. Salt is transparent or translucent and highly diathermous. It is colorless when pure and has a vitreous luster. Salt containing traces of iron oxides has varying shades of yellow, orange, brown, pink, or red. The peculiar shade of red sometimes found in that produced by solar evaporation of sea water has been attributed to tiny organisms. Blue mottlings sometimes seen in halite crystals have been attributed to colloidal sodium. Salt is soluble in water to the extent of 35.7 parts per 100 parts of water at 0°C and 39.8 parts per 100 of water at 100°C. The small difference in solubility with increasing temperature is important in the economics of producing salt by evaporating brine. Salt has a negative heat of solution which is 1.281 kg-cal/ mole at 18°C in 200 moles of water.

Jan 1, 1960

By J. S. Hromatko, L. J. Gurevich

In the course of the examination, at the BureLu of Standards, of fusible tin boiler plugs for the Steamboat Inspection Service, it became evident that an investigation should be undcrtaken to determine the precautions necessary in the manufacture of acceptable plugs. The results of the tests of these plugs show that their manufacture has improved, though at present not all of the plugs tested are, satisfactory. Table 1 gives the result of tests of some 1500 plugs from about 100 makers. Records of the tests show that several of the makers were able to produce satisfactory plugs with every pouring. The Steamboat Inspection Service has the following specifications for fusible plugs: "Fusible plugs for use in boilers of steam vessels under the jurisdiction of the Steamboat Inspection Service shall be made of bronze casing with the bore tapering continuously and openly from end to end, and filled from end to end with tin not less than 99.7 per cent. pure and to contain not more than 0.1 per cent. of lead and not more than 0.1 per cent. of zinc. The small end of the bore may be countersunk not more than 1/32 in. in depth and width, but no recess, thread, or cavity other than this countersink shall be allowed." Table 1.—Thirty-"five-mdh Testing Record of Fusible Plugs Causes of Rejection Inspection Period June-November, 1916.................. 311 32.8 47.2 3.8 11.5 15. 1 10.9 1 1.9 4.5 December, 1916-May, 1917............. 318 71.4 28.6 2.2 4.4 12.8 5.9 i ... 2.8 June-November, 1917.................. 228 73.0 27.01 ... 9.6, 5.2 9.6&apos; ... 0.8 December, 1917-May. 1918............. 214 72.028.0 0.9 0.4 11.6 7.0 ... 7.9 June-November, 1918...............250 70.7 29.3 ... 2.0 20.0 5.2 ....2.8 December, 1918-April. 1919............ 23378.121.9 7.2 1.2 1 4.7 3.0 ... 6.0 Total 35 months....................1544.69.7 30.3 2.3 4.8 11 0 6.9 0.3 4.1

Jan 1, 1921

By E. S. Moore

ALTHOUGH nickel was in use in alloys long before the Christian era, the metal was not discovered until 1751, when Cronstedt recognized it in niccolite from Sweden. The Chinese apparently used a nickel alloy, known as "pahfong" thousands of years ago and Persian coins dating farther back than 200 B.C. consist of a copper-nickel alloy similar to some of those now in use in coins. The pure metal was first prepared about 1775 and the metal was refined for commercial purposes some years later. The nickel industry did not attain much prominence until the ores in New Caledonia were discovered. Exports of ore from that country began in 1875 and since that date there has been an ever-increasing world output of nickel and a great expansion in the uses of the metal except during short periods of commercial and industrial depression. Previous to 1875, for a number of years, Norway was the chief producer, although the metal was mined also in Sweden, Finland, Italy, Germany, Austria, France, China, the United States and other countries. With the dis-covery of nickel deposits in the Sudbury district, Ontario, a new factor was introduced into the nickel industry and Sudbury has since become the overwhelmingly dominant feature in the world&apos;s nickel markets. Although nickel was first discovered in Canada as early as 1848 near the north shore of Lake Huron and nickel-copper sulfides were found in 1856 by surveyors working close to the present location of the important mine at Creighton, in the Sudbury field, it was not until 188.3 that any importance was attached to this field. In that year copper sulfide attracted attention where the main line of the Canadian Pacific railroad was being projected across Canada to the Pacific coast. Mining began near this discovery in 1889 but in the meantime operations had begun in 1886 in other parts of the field and by 1890 about 100,000 tons of ore had been raised. In the Sudbury field, as in Norway and at the old Lancaster Gap mine in Pennsylvania, the ore was first mined for its copper content and difficulty in the refining of the copper led to the discovery of the important proportions of nickel in the ore. No. 3 property of the Inter-national Nickel Co., now known as the Frood, the greatest deposit in the

Jan 1, 1932

By R. M. Brick

THE etched microstructures of cold-worked alpha brasses, after reduc-tions in excess of about 20 per cent, exhibit dark lines or markings, which have been termed "deformation bands," "etch bands," and "strain markings." The terms will be used synonomously in this report. The markings are similar in their general appearance to etch figures found in cold-worked iron, aluminum and other cubic metals but in certain respects may differ noticeably. At reductions of from about 20 to 50 per cent in brass, they appear as straight dark lines of irregular spacing and at random directions in different grains, but apparently intimately associated with definite crystallographic planes, usually {111}, in each crystal. At higher reductions, the markings on the rolling plane tend to appear in a direction transverse to the rolling direction in all crystals but may bend away at considerable angles, particularly near grain boundaries. Samans,1 on the basis of X-ray and micrographic studies of two single crystals of brass, rolled to a 50 per cent reduction, showed that the lines of deformation were the edges of thin mechanical twins parallel to octahedral planes. Barrett and Levenson2-4 have made comprehensive studies of the deformation of iron and of aluminum. They show that in these two metals the deformation markings originate by division of the original homogeneous crystal into banded areas differing in orientation by an amount that increases with the degree of deformation. The markings thus cannot be twin bands, and Barrett, in a review of this subject,2 attributed Samans&apos; results on brass to an accidental choice of deformation that left the bands in approximately a twinned relationship. On the other hand, Mathewson5 has suggested that in some cases mechanical twinning offers a better rationalization of the coverage of some (111) pole figures of worked brass than the assumption of band rotation into sym-metry positions. Considering next a deformed and annealed alpha brass, the most striking aspect of its microstructure is the multiplicity of twin bands.

Jan 1, 1940

By George Bell

THE mine and milling plant of Demonstration Gold Mines, Ltd., is near the city limits of Baguio, Mt. Province, P. I. The mine road connects with the main highway to Manila. The nearest railway point is near sea level, approximately 40 miles distant. The Baguio district is very mountainous and has one of the heaviest rainfalls in the world. It is therefore difficult to maintain roads or to impound tailings and mine dumps. All supplies are trucked into the district direct from Manila or the nearest railway point, which means uncertain deliveries and high freight rates. Installation of equipment is difficult and costly. The average elevation at the mine is 4000 ft. and the climatic condi-tions.are ideal except for a three months rainy season. The company generates its own power for mining and milling opera-tions with three 400-hp. Ruston Diesel engines direct connected to 250-kw. General Electric alternating current generators. Labor conditions have been excellent, although at present social security laws are causing some unrest. Labor receives a higher average wage rate in this district than other labor in the Islands. The com-pany also furnishes free living quarters, hospitalization and work-men&apos;s compensation. Taxation has been reasonable up to the present time, but some of the new mining legislation may make it difficult to operate and pay dividends. The future depends largely upon the continuation of $35 gold and the political outcome in the Islands.

Jan 1, 1939

By Edward Saibel

The various theories that have been advanced to explain or predict the conditions under which a metal fractures may be divided into two categories: First, there are the macroscopic theories generally used in engineering practice. These are empirical in nature and limited in application. For example, the maximum normal stress criterion, which is quite satisfactory for a mild steel in simple tension at atmospheric pressure,&apos; no longer suffices when this steel is pulled under hydrostatic pressure.2 In all of these empirical theories, the critical condition characteristic of the material and of the loading conditions must be obtained experimentally. Secondly, there are the theories based on interatomic forces,3&apos;4 or on the energy required to form new surfaces.5,6 These have all dealt with the theoretical evaluation of the tensile stress necessary to bring about rupture in a purely brittle manner; that is, without plastic flow preceding fracture. All of these attempts have led to values of the tensile strength of crystals or of polycrystalline bodies that are 100 to 1000 times higher than observed values. On this account, it has been thought necessary by some investigators to conceive of a microcrack structure or distribution of flaws throughout the specimen such that the resulting stress concentrations provide the factor necessary to bring about agree- ment between calculation and experiment. It has been pointed out by several observers&apos; that this point of view is highly unrealistic, in that the weakening effect of these flaws or microstructures must be very uniform from specimen to specimen, since the fracture stresses found for various specimens of the same material tested under similar conditions are so nearly constant. Furthermore, since calculations based on atomic forces or atomic energy are for purely brittle fracture, a condition probably never satisfied in tests, agreement is hardly to be expected. Thermodynamic Theory of Fürth In order to resolve this apparent discrepancy between the theoretical cohesive strengths and the observed fracture strengths, Fürth8 advanced a thermodynamic theory of the tensile strength of isotropic bodies based on work of Born relating to the melting of crystals. Assuming an isotropic material free from imperfections and flaws, behaving elastically up to the breaking point, and assuming a connection between rupture and the melting phenomenon, Fürth obtains an expression for the rupture stress a, in the form where Q is the melting energy per unit mass, p is the density, and is Poisson&apos;s ratio. Furth compares fracture stresses computed from Eq I with the fracture stresses of metals as given in the Landolt-Bernstein Tables (1927) and in the Hand-

Jan 1, 1947

By Edward Saibel

The various theories that have been advanced to explain or predict the conditions under which a metal fractures may be divided into two categories: First, there are the macroscopic theories generally used in engineering practice. These are empirical in nature and limited in application. For example, the maximum normal stress criterion, which is quite satisfactory for a mild steel in simple tension at atmospheric pressure,&apos; no longer suffices when this steel is pulled under hydrostatic pressure.2 In all of these empirical theories, the critical condition characteristic of the material and of the loading conditions must be obtained experimentally. Secondly, there are the theories based on interatomic forces,3&apos;4 or on the energy required to form new surfaces.5,6 These have all dealt with the theoretical evaluation of the tensile stress necessary to bring about rupture in a purely brittle manner; that is, without plastic flow preceding fracture. All of these attempts have led to values of the tensile strength of crystals or of polycrystalline bodies that are 100 to 1000 times higher than observed values. On this account, it has been thought necessary by some investigators to conceive of a microcrack structure or distribution of flaws throughout the specimen such that the resulting stress concentrations provide the factor necessary to bring about agree- ment between calculation and experiment. It has been pointed out by several observers&apos; that this point of view is highly unrealistic, in that the weakening effect of these flaws or microstructures must be very uniform from specimen to specimen, since the fracture stresses found for various specimens of the same material tested under similar conditions are so nearly constant. Furthermore, since calculations based on atomic forces or atomic energy are for purely brittle fracture, a condition probably never satisfied in tests, agreement is hardly to be expected. Thermodynamic Theory of Fürth In order to resolve this apparent discrepancy between the theoretical cohesive strengths and the observed fracture strengths, Fürth8 advanced a thermodynamic theory of the tensile strength of isotropic bodies based on work of Born relating to the melting of crystals. Assuming an isotropic material free from imperfections and flaws, behaving elastically up to the breaking point, and assuming a connection between rupture and the melting phenomenon, Fürth obtains an expression for the rupture stress a, in the form where Q is the melting energy per unit mass, p is the density, and is Poisson&apos;s ratio. Furth compares fracture stresses computed from Eq I with the fracture stresses of metals as given in the Landolt-Bernstein Tables (1927) and in the Hand-

Jan 1, 1947